DOCSLIB.ORG

Performance Plus Racing Oils SK-12042 and SK-12242 Safety Data Sheet SDS ID: 820275

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Performance Plus Racing Oils SK-12042 and SK-12242 Safety Data Sheet SDS ID: 820275 Performance Plus Racing Oils SK-12042 and SK-12242 Safety Data Sheet SDS ID: 820275 Section 1 - PRODUCT AND COMPANY IDENTIFICATION Material Name Performance Plus Racing Oils SK-12042 and SK-12242 Product Code Prefix 11 Product Use Motor oil. If this product is used in combination with other products, refer to the Safety Data Sheet for those products. Restrictions on Use None known. FOR PRODUCT MANUFACTURED IN THE U.S.A.: MANUFACTURER SUPPLIER (in Canada) Safety-Kleen Systems, Inc. Safety-Kleen Canada, Inc. 42 Longwater Drive 25 Regan Road Norwell, MA 02061-9149 Brampton, Ontario, L7A 1B2 U.S.A. Canada FOR PRODUCT MANUFACTURED IN CANADA: MANUFACTURER SUPPLIER (in the U.S.A.) Safety-Kleen Canada Inc. Safety-Kleen Systems, Inc. 25 Regan Road 42 Longwater Drive Brampton, Ontario, L7A 1B2 Norwell, MA 02061-9149 Canada U.S.A. www.safety-kleen.com Phone: 1-800-669-5740 Emergency Phone #: 1-800-468-1760 Issue Date June 3, 2020 Supersedes Issue Date January 12, 2017 Original Issue Date January 12, 2017 Section 2 - HAZARDS IDENTIFICATION Classification in accordance with Schedule 1 of Canada’s Hazardous Products Regulations (HPR) (SOR/2015-17) and paragraph (d) of 29 CFR 1910.1200 in the United States Acute Toxicity - Inhalation - Vapor - Category 3 Skin Corrosion/Irritation - Category 2 Skin Sensitization - Category 1A GHS Label Elements Symbol(s) Safety Data Sheet Material Name: Performance Plus Racing Oils SK-12042 and SK-12242 SDS ID: 820275 Signal Word Danger Hazard Statement(s) Toxic if inhaled. Causes skin irritation. May cause an allergic skin reaction. Precautionary Statement(s) Prevention Avoid breathing dust/fume/gas/mist/vapors/spray. Use only outdoors or in a well-ventilated area. Wear protective gloves/protective clothing/eye protection/face protection. Wash thoroughly after handling. Contaminated work clothing must not be allowed out of the workplace. Response IF INHALED: Remove person to fresh air and keep comfortable for breathing. Call a POISON CENTER or doctor/physician if you feel unwell. IF ON SKIN: Wash with plenty of soap and water. If skin irritation or rash occurs: Get medical advice/attention. Take off contaminated clothing and wash before reuse. IF SWALLOWED: Do NOT induce vomiting. Immediately get medical attention. Storage Store in a well-ventilated place. Keep container tightly closed. Store locked up. Disposal Dispose of contents/container in accordance with local/regional/national/international regulations. Statement(s) of Unknown Acute Toxicity Inhalation 88.4% of the mixture consists of ingredient(s) of unknown acute toxicity. Section 3 - COMPOSITION / INFORMATION ON INGREDIENTS CAS Component Name Percent 64742-58-1 Lubricating oils, petroleum, hydrotreated spent 40-45 68037-01-4 1-Decene, homopolymer, hydrogenated 0-30 1-Dodecene, polymer with 1-decene and 1-octene, 163149-28-8 0-30 hydrogenated 151006-60-9 1-Dodecene, polymer with 1-decene, hydrogenated 0-30 68649-11-6 1-Decene, dimer, hydrogenated 0-20 Lubricating oils, petroleum, C20-50, hydrotreated 72623-87-1 1-10 neutral oil-based Phosphorodithioic acid, O,O-di-C1-14-alkyl esters, 68649-42-3 1-5 zinc salts 64742-79-6 Gas oils, petroleum, hydrodesulfurized 0.1-5 64742-46-7 Distillates, petroleum, hydrotreated middle 0.1-5 Lubricating oils, petroleum, C15-30, hydrotreated 72623-86-0 0.1-1 neutral oil-based ____________________________________________________________ Page 2 of 12 Rev. 06/20 Safety Data Sheet Material Name: Performance Plus Racing Oils SK-12042 and SK-12242 SDS ID: 820275 97-88-1 Butyl methacrylate 0.01-0.1 Section 4 - FIRST AID MEASURES Inhalation IF INHALED: Remove person to fresh air and keep comfortable for breathing. Call a POISON CENTER or doctor/physician if you feel unwell. If breathing is difficult, oxygen should be administered by qualified personnel. Skin IF ON SKIN: Wash with plenty of soap and water. If skin irritation or rash occurs: Get medical advice/attention. Eyes IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists, get medical advice/attention. Ingestion IF SWALLOWED: Do NOT induce vomiting. Immediately get medical attention. If spontaneous vomiting occurs, keep head below hips to avoid breathing the product into the lungs. Never give anything by mouth to an unconscious person. Most Important Symptoms/Effects Acute Toxic if inhaled. Causes skin irritation. May cause allergic skin reaction. May cause eye irritation. Delayed No information on significant adverse effects. Indication of any immediate medical attention and special treatment needed Treat symptomatically and supportively. Treatment may vary with condition of victim and specifics of incident. Call 1-800-468-1760 for additional information. Section 5 - FIRE FIGHTING MEASURES Extinguishing Media Suitable Extinguishing Media Carbon dioxide, regular foam, dry chemical, water spray, or water fog. Unsuitable Extinguishing Media Do not use high-pressure water streams. Special Hazards Arising from the Chemical Fire may produce irritating, poisonous and/or corrosive fumes. Containers may rupture or explode if exposed to heat. Empty product containers may retain product residue and can be dangerous. Product is not sensitive to mechanical impact or static discharge. Hazardous Combustion Products Burning may produce: Oxides of carbon, miscellaneous decomposition products. Fire Fighting Measures Move container from fire area if it can be done without risk. Keep storage containers cool with water spray. For massive fire, use unmanned hose holders or monitor nozzles; if this is impossible withdraw from area and let fire burn. Special Protective Equipment and Precautions for Firefighters A positive-pressure, self-contained breathing apparatus (SCBA) and full-body protective equipment are required for fire emergencies. ____________________________________________________________ Page 3 of 12 Rev. 06/20 Safety Data Sheet Material Name: Performance Plus Racing Oils SK-12042 and SK-12242 SDS ID: 820275 Section 6 - ACCIDENTAL RELEASE MEASURES Personal Precautions, Protective Equipment and Emergency Procedures Wear personal protective clothing and equipment, see Section 8. Avoid release to the environment. Methods and Materials for Containment and Cleaning Up Remove all ignition sources. Do not touch or walk through spilled product. Stop leak if you can do it without risk. Wear protective equipment and provide engineering controls as specified in SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION. Isolate hazard area. Keep unnecessary and unprotected personnel from entering. Ventilate area and avoid breathing vapor or mist. A vapor suppressing foam may be used to reduce vapors. Contain spill away from surface water and sewers. Contain spill as a liquid for possible recovery, or sorb with compatible sorbent material and shovel with a clean, sparkproof tool into a sealable container for disposal. Additionally, for large spills: Water spray may reduce vapor, but may not prevent ignition in closed spaces. Dike far ahead of liquid spill for collection and later disposal. There may be specific federal regulatory reporting requirements associated with spills, leaks, or releases of this product. Also see SECTION 15: REGULATORY INFORMATION. Section 7 - HANDLING AND STORAGE Precautions for Safe Handling Keep away from sparks or flame. Where flammable mixtures may be present, equipment safe for such locations should be used. Use clean tools and explosion-proof equipment. When transferring large volumes of product, metal containers, including trucks and tank cars, should be grounded and bonded. However, when aerosolizing, misting, or heating this product, do not breathe vapor or mist. Use in a well ventilated area. Avoid contact with eyes, skin, clothing, shoes. Conditions for Safe Storage, Including any Incompatibilities Store in a well-ventilated place. Keep container tightly closed. Store locked up. Keep container tightly closed when not in use and during transport. Store containers in a cool, dry place. Do not pressurize, cut, weld, braze, solder, drill, or grind containers. Keep containers away from flame or other sources of ignition. Empty product containers may retain product residue and can be dangerous. Incompatible Materials Strong oxidizing agents. Section 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION Component Exposure Limits ACGIH, OSHA, and NIOSH have not developed exposure limits for any of this product’s components. ACGIH - Threshold Limit Values - Biological Exposure Indices (BEI) There are no biological limit values for any of this product's components. Engineering Controls Provide general ventilation. Where adequate general ventilation is unavailable, use process enclosures, local exhaust ventilation, or other engineering controls. Individual Protection Measures, such as Personal Protective Equipment Eye/face protection Wear safety glasses. Additional protection like goggles, face shields, or respirators may be needed dependent upon anticipated use and concentrations of mists or vapors. Eye wash fountain and emergency showers are recommended. Contact lens use is not recommended. Respiratory Protection A respiratory protection program which meets USA's OSHA General Industry Standard 29 CFR 1910.134 or Canada's CSA Standard Z94.4-M1982 requirements must be followed whenever workplace conditions warrant a respirator's use. Consult a qualified Industrial Hygienist or Safety Professional for respirator selection guidance. ____________________________________________________________
Load more

Recommended publications
  • Alfa Olefins Cas N
    OECD SIDS ALFA OLEFINS FOREWORD INTRODUCTION ALFA OLEFINS CAS N°:592-41-6, 111-66-0, 872-05-9, 112-41-4, 1120-36-1 UNEP PUBLICATIONS 1 OECD SIDS ALFA OLEFINS SIDS Initial Assessment Report For 11th SIAM (Orlando, Florida, United States 1/01) Chemical Name: 1-hexene Chemical Name: 1-octene CAS No.: 592-41-6 CAS No.: 111-66-0 Chemical Name: 1-decene Chemical Name: 1-dodecene CAS No.: 872-05-9 CAS No.: 112-41-4 Chemical Name: 1-tetradecene CAS No.: 1120-36-1 Sponsor Country: United States National SIDS Contract Point in Sponsor Country: United States: Dr. Oscar Hernandez Environmental Protection Agency OPPT/RAD (7403) 401 M Street, S.W. Washington, DC 20460 Sponsor Country: Finland (for 1-decene) National SIDS Contact Point in Sponsor Country: Ms. Jaana Heiskanen Finnish Environment Agency Chemicals Division P.O. Box 140 00251 Helsinki HISTORY: SIDS Dossier and Testing Plan were reviewed at the SIDS Review Meeting or in SIDS Review Process on October 1993. The following SIDS Testing Plan was agreed: No testing ( ) Testing (x) Combined reproductive/developmental on 1-hexene, combined repeat dose/reproductive/developmental on 1-tetradecene and acute fish, daphnid and algae on 1- tetradecene. COMMENTS: The following comments were made at SIAM 6 and have been incorporated in this version of the SIAR: 2 UNEP PUBLICATIONS OECD SIDS ALFA OLEFINS 1. The use of QSAR calculations for aquatic toxicity, 2. More quantitative assessment of effects; and 3. Provide more details for each endpoint. The following comments were made at SIAM 6, but were not incorporated into the SIAR for the reasons provided: 1.
    [Show full text]
  • Radical Approaches to Alangium and Mitragyna Alkaloids
    Radical Approaches to Alangium and Mitragyna Alkaloids A Thesis Submitted for a PhD University of York Department of Chemistry 2010 Matthew James Palframan Abstract The work presented in this thesis has focused on the development of novel and concise syntheses of Alangium and Mitragyna alkaloids, and especial approaches towards (±)-protoemetinol (a), which is a key precursor of a range of Alangium alkaloids such as psychotrine (b) and deoxytubulosine (c). The approaches include the use of a key radical cyclisation to form the tri-cyclic core. O O O N N N O O O H H H H H H O N NH N Protoemetinol OH HO a Psychotrine Deoxytubulosine b c Chapter 1 gives a general overview of radical chemistry and it focuses on the application of radical intermolecular and intramolecular reactions in synthesis. Consideration is given to the mediator of radical reactions from the classic organotin reagents, to more recently developed alternative hydrides. An overview of previous synthetic approaches to a range of Alangium and Mitragyna alkaloids is then explored. Chapter 2 follows on from previous work within our group, involving the use of phosphorus hydride radical addition reactions, to alkenes or dienes, followed by a subsequent Horner-Wadsworth-Emmons reaction. It was expected that the tri-cyclic core of the Alangium alkaloids could be prepared by cyclisation of a 1,7-diene, using a phosphorus hydride to afford the phosphonate or phosphonothioate, however this approach was unsuccessful and it highlighted some limitations of the methodology. Chapter 3 explores the radical and ionic chemistry of a range of silanes.
    [Show full text]
  • Self-Metathesis of 1-Octene Using Alumina-Supported Re2o7 in Supercritical CO2
    Top Catal DOI 10.1007/s11244-008-9154-4 ORIGINAL PAPER Self-Metathesis of 1-Octene Using Alumina-Supported Re2O7 in Supercritical CO2 Massimo Fabris Æ Cindy Aquino Æ Antony J. Ward Æ Alvise Perosa Æ Thomas Maschmeyer Æ Maurizio Selva Ó Springer Science+Business Media, LLC 2009 Abstract In this contribution we describe the use of basic science has been applied for the benefit of man, heterogeneous catalysts for the liquid-phase self-metathesis society and the environment’’.1 Their contribution was of 1-octene in supercritical CO2. Our work aims at recognized for understanding the mechanism, and for addressing the mass-transfer problems associated with such developing very efficient and selective discrete metal- reaction systems. By coupling a heterogeneous supported based catalysts. Re2O7 catalyst with the use of scCO2, the self-metathesis Nonetheless, one should not forget that the metathesis of 1-octene takes place by and large much more rapidly reaction using heterogeneous catalysis has been an estab- than in traditional solvent media, and furthermore, by using lished industrial process since 1966, based on the use of scCO2 the overall efficiency and sustainability of the supported (usually on silica and alumina) metal oxides transformation can be improved. such as tungsten, nickel, cobalt, rhenium, and molybde- num. Three significant examples come to mind and are Keywords Metathesis Á 1-Octene Á Supercritical CO2 Á here recalled briefly. [1]. Re/Al O 2 3 1. The historic Phillips triolefin process for the produc- tion of ethene and 2-butene from propene using a WO /SiO catalyst, [2] that was shut down in 1972 1 Introduction 3 2 after 6 years of operation due to increased demand for propene, and later reutilized in the reverse direction to The metathesis of olefins is a very elegant and widely produce propene.
    [Show full text]
  • Selective Oxidation of Polynuclear Aromatic Hydrocarbons
    SELECTIVE OXIDATION OF POLYNUCLEAR AROMATIC HYDROCARBONS Thesis submitted in accordance with the requirements of Cardiff University for the degree of Doctor of Philosophy EWA NOWICKA July 2012 DECLARATION This work has not been submitted in substance for any other degree or award at this or any other university or place of learning, nor is being submitted concurrently in candidature for any degree or other award. Signed ………………………………………… (candidate) Date ................................. STATEMENT 1 This thesis is being submitted in partial fulfillment of the requirements for the degree of Doctor of Philosophy Signed ………………………………………… (candidate) Date ………………………… STATEMENT 2 This thesis is the result of my own independent work/investigation, except where otherwise stated. Other sources are acknowledged by explicit references.The views expressed are my own. Signed ………………………………………… (candidate) Date ………………………… STATEMENT 3 I hereby give consent for my thesis, if accepted, to be available for photocopying and for inter-library loan, and for the title and summary to be made available to outside organisations. Signed ………………………………………… (candidate) Date ………………………… STATEMENT 4: PREVIOUSLY APPROVED BAR ON ACCESS I hereby give consent for my thesis, if accepted, to be available for photocopying and for inter-library loans after expiry of a bar on access previously approved by the Academic Standards & Quality Committee. Signed ………………………………………… (candidate) Date ………………………… “You never fail until you stop trying.” Albert Einstein Abstract This thesis targets the selective oxidation of polynuclear aromatic compounds, which is considered as a preliminary step of upgrading of heavy oils, resids and bitumens to higher value materials in the liquid phase using different catalytic systems. Oxidation studies concentrated on simple model polyaromatic compounds and their alkylated derivatives.
    [Show full text]
  • Radical Hydroacylation of C-C and N-N Double Bonds in Air
    University College London Radical Hydroacylation of C-C and N-N Double Bonds in Air by Jenna Marie Ahern Submitted in partial fulfilment of the requirements for the degree of Doctor of Philosophy Declaration I, Jenna Marie Ahern, confirm that the work presented in this thesis is my own. Where information has been derived from other sources, I confirm that this has been indicated in the thesis. Jenna Marie Ahern October 2010 Radical Hydroacylation of C-C and N-N Double Bonds in Air Jenna Marie Ahern Abstract The formation of C-C and C-N bonds in modern organic synthesis is a key target for methodological advancement. Current methods of C-C and C-N bond formation often involve the use of expensive catalysts, or sub-stoichiometric reagents, which can lead to the generation of undesirable waste products. This thesis describes a novel and environmentally benign set of reaction conditions for the formation of C-C and C-N bonds by hydroacylation and this is promoted by mixing two reagents, an aldehyde and an electron-deficient double bond, under freely available atmospheric oxygen at room temperature Chapter 1 will provide an introduction to the thesis and mainly discusses methods for C-C bond formation, in particular, radical chemistry and hydroacylation. Chapter 2 describes the hydroacylation of vinyl sulfonates and vinyl sulfones (C-C double bonds) with aliphatic and aromatic aldehydes with a discussion and evidence for the mechanism of the transformation. Chapter 3 details the synthesis of precursors for intramolecular cyclisations and studies into aerobic intramolecular cyclisations. Chapter 4 describes the hydroacylation of vinyl phosphonates (C-C double bonds) and diazocarboxylates (N-N double bonds) with aliphatic and aromatic aldehydes bearing functional groups.
    [Show full text]
  • Linear Alpha-Olefins (681.5030)
    IHS Chemical Chemical Economics Handbook Linear alpha-Olefins (681.5030) by Elvira O. Camara Greiner with Yoshio Inoguchi Sample Report from 2010 November 2010 ihs.com/chemical November 2010 LINEAR ALPHA-OLEFINS Olefins 681.5030 B Page 2 The information provided in this publication has been obtained from a variety of sources which SRI Consulting believes to be reliable. SRI Consulting makes no warranties as to the accuracy completeness or correctness of the information in this publication. Consequently SRI Consulting will not be liable for any technical inaccuracies typographical errors or omissions contained in this publication. This publication is provided without warranties of any kind either express or implied including but not limited to implied warranties of merchantability fitness for a particular purpose or non-infringement. IN NO EVENT WILL SRI CONSULTING BE LIABLE FOR ANY INCIDENTAL CONSEQUENTIAL OR INDIRECT DAMAGES (INCLUDING BUT NOT LIMITED TO DAMAGES FOR LOSS OF PROFITS BUSINESS INTERRUPTION OR THE LIKE) ARISING OUT OF THE USE OF THIS PUBLICATION EVEN IF IT WAS NOTIFIED ABOUT THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES THE ABOVE LIMITATION MAY NOT APPLY TO YOU. IN SUCH STATES SRI CONSULTING’S LIABILITY IS LIMITED TO THE MAXIMUM EXTENT PERMITTED BY SUCH LAW. Certain statements in this publication are projections or other forward-looking statements. Any such statements contained herein are based upon SRI Consulting’s current knowledge and assumptions about future events including without limitation anticipated levels of global demand and supply expected costs trade patterns and general economic political and marketing conditions.
    [Show full text]
  • Speciated Organic Gas Emissions Aircraft Turbofan Turbonjet Turboprop
    RECOMMENDED BEST PRACTICE FOR QUANTIFYING SPECIATED ORGANIC GAS EMISSIONS FROM AIRCRAFT EQUIPPED WITH TURBOFAN, TURBOJET, AND TURBOPROP ENGINES Federal Aviation Administration Office of Environment and Energy and U.S. Environmental Protection Agency Office of Transportation and Air Quality Version 1.0 May 27, 2009 ACKNOWLEDGEMENTS The Federal Aviation Administration (FAA) Office of Environment and Energy (AEE) and the U.S. Environmental Protection Agency (EPA) Office of Transportation Air Quality (OTAQ) would like to acknowledge the following agencies and individuals for their contribution to this document: FAA – Ralph Iovinelli, Mohan Gupta, Carl Ma, and Ed McQueen EPA – Bryan Manning, Rich Cook, Kent Helmer, Ken Petche, John Kinsey, Rich Wilcox, Kathryn Sergeant, Marion Hoyer, Laurel Driver, and Suzanne King California Air Resources Board – Steve Francis, Paul Allen, Wenli Yang, and Steve Church Aerodyne Research, Inc. – Rick Miake-Lye and Scott Herndon Montana State University – Berk Knighton KB Environmental Sciences, Inc. – Carrol Bryant, Mike Ratte, Paul Sanford, and Mike Kenney This document was prepared for the Federal Aviation Administration, Office of Environment and Energy by KB Environmental Sciences Inc. with assistance from CSSI Inc. in support of CSSI’s Contract DTFAWA-05-C-00044, Technical Directive Memorandum B-002-011. EXECUTIVE SUMMARY This document presents an approach to, and technical support for, the quantification of organic gas (OG) emissions including hazardous air pollutants (HAPs) from aircraft equipped with turbofan, turbojet and turboprop engines.1,2,3 This Recommended Best Practice (RBP) was produced through an inter-agency partnership and collaborative effort between the Federal Aviation Administration (FAA) Office of Environment and Energy (AEE) and the U.
    [Show full text]
  • Hydrocarbons Thermal Cracking Selectivity Depending on Their Structure and Cracking Parameters
    Master in Chemical Engineering Hydrocarbons Thermal Cracking Selectivity Depending on Their Structure and Cracking Parameters Thesis of the Master’s Degree Development Project in Foreign Environment Cláudia Sofia Martins Angeira Erasmus coordinator: Eng. Miguel Madeira Examiner in FEUP: Eng. Fernando Martins Supervisor in ICT: Doc. Ing Petr Zámostný July 2008 Acknowledgements I would like to thank Doc. Ing. Petr Zámostný for the opportunity to hold a master's thesis in this project, the orientation, the support given during the laboratory work and suggestions for improvement through the work. i Hydrocarbons Thermal Cracking Selectivity Depending on Their Structure and Cracking Parameters Abstract This research deals with the study of hydrocarbon thermal cracking with the aim of producing ethylene, one of the most important raw materials in Chemical Industry. The main objective was the study of cracking reactions of hydrocarbons by means of measuring the selectivity of hydrocarbons primary cracking and evaluating the relationship between the structure and the behavior. This project constitutes one part of a bigger project involving the study of more than 30 hydrocarbons with broad structure variability. The work made in this particular project was focused on the study of the double bond position effect in linear unsaturated hydrocarbons. Laboratory experiments were carried out in the Laboratory of Gas and Pyrolysis Chromatography at the Department of Organic Technology, Institute of Chemical Technology, Prague, using for all experiments the same apparatus, Pyrolysis Gas Chromatograph, to increase the reliability and feasibility of results obtained. Linear octenes with different double bond position in hydrocarbon chain were used as model compounds. In order to achieve these goals, the primary cracking reactions were studied by the method of primary selectivities.
    [Show full text]
  • Light Linear Alpha Olefin Market Study
    IHS CHEMICAL Light Linear Alpha Olefin Market Study Special Report Prospectus IHS CHEMICAL Contents Contents ..................................................................................................................................... 2 Introduction ................................................................................................................................ 3 Study Scope ............................................................................................................................... 5 Key Questions Addressed in the Study ...................................................................................... 7 Deliverables ............................................................................................................................... 8 Proposed Table of Contents ...................................................................................................... 9 Methodology ............................................................................................................................ 11 Study Team .............................................................................................................................. 15 Qualifications............................................................................................................................ 18 About IHS Chemical ................................................................................................................. 21 About IHS ................................................................................................................................
    [Show full text]
  • Fastest Formation Routes of Nanocarbons in Solution Plasma
    www.nature.com/scientificreports OPEN Fastest Formation Routes of Nanocarbons in Solution Plasma Processes Received: 18 August 2016 Tetsunori Morishita1, Tomonaga Ueno1,2,3, Gasidit Panomsuwan2, Junko Hieda1, Accepted: 24 October 2016 Akihito Yoshida1, Maria Antoaneta Bratescu1 & Nagahiro Saito1,2,3 Published: 14 November 2016 Although solution-plasma processing enables room-temperature synthesis of nanocarbons, the underlying mechanisms are not well understood. We investigated the routes of solution-plasma- induced nanocarbon formation from hexane, hexadecane, cyclohexane, and benzene. The synthesis rate from benzene was the highest. However, the nanocarbons from linear molecules were more crystalline than those from ring molecules. Linear molecules decomposed into shorter olefins, whereas ring molecules were reconstructed in the plasma. In the saturated ring molecules, C–H dissociation proceeded, followed by conversion into unsaturated ring molecules. However, unsaturated ring molecules were directly polymerized through cation radicals, such as benzene radical cation, and were converted into two- and three-ring molecules at the plasma–solution interface. The nanocarbons from linear molecules were synthesized in plasma from small molecules such as C2 under heat; the obtained products were the same as those obtained via pyrolysis synthesis. Conversely, the nanocarbons obtained from ring molecules were directly synthesized through an intermediate, such as benzene radical cation, at the interface between plasma and solution, resulting in the same products as those obtained via polymerization. These two different reaction fields provide a reasonable explanation for the fastest synthesis rate observed in the case of benzene. Liquid-phase plasma1–5 has attracted the attention of several researchers engaged in plasma science, especially for applications involving materials and water treatment6–10.
    [Show full text]
  • Factors Influencing the Competitive Rates of Free-Radical Addition of Ethyl 2-Bromo
    AN ABSTRACT OF THE THESIS OF Vahid Ghodoussi for the degree of Master of Science in Chemistry presented on May 14, 1986 Title: Factors Influencing the Competitive Rates of Free-Radical Addition of Ethyl 2-Bromo- carboxylates to Selected Alkene Pairs Redacted for Privacy Abstract approved: v Gerald Jay Gleicher A study of the effects of structural modification at the alpha position of ethyl 2-bromocarboxylates on their rates of addition to two alkene pairs was undertaken. In the competition between 3-propoxypropene and 1-octene at 70°, a 37% increase in selectivity was observed in going from carboxylates generating primary radicals to those generating tertiary radicals. These results yield good correlations with electronic and/or steric parameters. When the competition between 1-methylcyclohexene and 1-octene was examined, no simple systematic variation of selectivity with structure was observed. An explanation is offered, which is based on the greater persistence of hindered carboethoxyalkyl radicals and the resultant changes in transition state structure. Factors Influencing the Competitive Rates of Free-Radical Addition of Ethyl 2-Bromocarboxylates to Selected Alkene Pairs by Vahid Ghodoussi A THESIS submitted to Oregon State University in partial fulfillment of the requirements for the degree of Master of Science Completed May 14, 1986 Commencement June 1987 APPROVED: Redacted for Privacy Professor of Chemistry in charge of major Redacted for Privacy Head of Department of Chemistry Redacted for Privacy Dean of Grrlate Sehootf Date thesis is presented May 14, 1986 Typed by Violet Jonas for Vahid Ghodoussi ACKNOWLEDGMENT First and foremost, I wish to express deep gratitude to my parents, my brother, and other members of my family for their continuous understanding and support.
    [Show full text]
  • Chm 416 Course Title: Organic Synthesis
    NATIONAL OPEN UNIVERSITY OF NIGERIA SCHOOL OF SCIENCE AND TECHNOLOGY COURSE CODE: CHM 416 COURSE TITLE: ORGANIC SYNTHESIS Course Developer/Writer: Adeniran, Oluremi Isola Department of Chemistry Faculty of Science University of Abuja, Abuja, Nigeria. MODULE 1 Oxidation Reactions Unit 1 Oxidation reactions Unit 2 Transformation of alkenes Unit 3 Transformation of alcohols Unit 4 Transformation of arenes UNIT 1 Oxidation reactions Contents 1.0 Introduction 2.0 Objectives 3.0 Main Content 3.1 Definitions 3.2 Oxidizing Reagents 4.0 Conclusion 5.0 Summary 6.0 Tutor-Marked Assignment 7.0 References/Further Reading 1.0 Introduction Oxidation as defined in ionic and free radical reactions, is a process by which an element undergoes a net loss of electrons. The concept as applied to organic covalent compounds, where elements share electrons rather than losing or gaining them is the same, but it’s often simplified and narrowed down to make it easier to recognize this process. Therefore it must be kept in mind that, while the following definition in this unit is grossly simplified, it serves the goal of quickly identifying oxidation process in many organic reactions. 2.0 Objectives At the end of this unit, students should be able to: i. Define oxidation reaction ii. Recognize oxidation in organic reactions iii. List some oxidizing reagents 3.0 Main content 3.1 Definitions Oxidation in inorganic chemistry is considered as a loss of electrons. For inorganic ions, as when Fe2+ is oxidized to Fe3+, this concept works well. Since most organic compounds are uncharged, electron gain or loss is not apparent.
    [Show full text]