Ships in 2-10 Days All Plywood Construction Soft Close Doors & Drawers 40 Door Styles SPECIFICATION GUIDE READY-TO-ASSEMBLE KITCHEN AND BATH CABINETRY hdckitchens.com Ready-to-Assemble Kitchen & Bath Cabinetry 5 Year Limited Warranty

Home Decorators Collection Cabinetry (warrantor) warrants to the original consumer purchaser only, that the Home Decorators Collection branded Ready-to-Assemble (RTA) products will be free from defects in material and workmanship. This warranty is for a period of five years as long as you own the cabinetry and is not transferable to subsequent owners.

This warranty does not cover damage resulting from normal wear, accident, misuse or lack of reasonable and necessary maintenance and service; nor does it warranty the improper installation or unauthorized repair, alteration, or modification or defects in the product when the product is installed. This warranty is limited to the repair or replacement of the defective part at the sole discretion of warrantor. Warranty is limited to Home Decorators Collection Cabinetry branded products excluding all electrical components: Excluded items may carry separate warranties as provided directly by the manufacturer of these products.

It is our option to provide repair parts or replace with functionally equivalent product. Return of product may be required for replacements. Such repair parts or replacement shall be at warrantor's expense, but customer shall bear all other expenses, including, but not limited to, cost of removal, transportation, re-installation, communication and any special service required by customer such as, overtime labor, etc. Due to the nature of the product, replacement product may vary in color from original purchased product.

Natural woods vary in color and grain pattern and exhibit color change over time. Cabinets may darken or lighten with age due to exposure to certain environmental conditions including but not limited to sunlight, moisture, household cleaners, smoke, etc. These variations are considered the natural characteristics of the material and are not covered under this warranty.

In the event of a Home Decorators Collection Cabinetry brand warranted product performance issue, submit request including proof of purchase documentation, specific description of warranty issue (include photos where possible) in writing to:

Warranty Department 210 Century Boulevard Bartow, FL 33830

EXCEPT TO THE EXTENT PROVIDED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE SHORTER OF THE PERIOD PROVIDED BY LAW OR THE PERIOD OF THIS WARRANTY, AND UNDER NO CIRCUMSTANCE SHALL HOME DECORATORS COLLECTION CABINETRY BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES SUSTAINED IN CONNECTION WITH THE PRODUCT. THE EXPRESS WARRANTY ABOVE CONSTITUTES THE ENTIRE WARRANTY AND IS IN LIEU OF ALL OTHERS EXPRESSED OR IMPLIED.

Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitation on how long an implied warranty lasts, therefore, the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.

INDEMNITY

Home Decorators Collection Cabinetry shall not be liable for either its failure to perform or its delays in performance hereunder arising out of or resulting from causes beyond its control, including but not limited to, acts of God, acts of Representation, acts of Government, wars, fires, floods, epidemics, quarantine, strike, freight embargoes, weather or default by suppliers due to any such causes. Table of Contents

Door Styles & Colors ...... 4-7

Construction Details ...... 8

Finished Ends ...... 9

Wall Cabinets ...... 10-13

Base Cabinets ...... 14-19

Tall Cabinets ...... 20-21

Vanities ...... 22

Decorative Moldings ...... 23-26

Interior Accessories ...... 27-29

Required Items List ...... 30-31

Decorative Hardware ...... 32-34 Ships in 2-3 Days! Express Select Door Styles

Ancona - Birch Available Colors:

• 3/4" thick x 2" wide solid birch frame doors with solid birch raised center panels • 3/4" thick birch veneer over MDF flat panel drawer fronts with solid birch edging • Concealed hinges with 6-way Mocha (AMG) adjustment and Soft Close damper • 5/8" thick plywood drawers with full-extension Soft Close runners • Full Overlay door style – decorative hardware required

Cumin (ACN)

Anzio - MDF/Thermofoil Available Colors:

• 3/4" thick solid MDF raised panel vinyl clad doors • 3/4" thick solid MDF flat panel vinyl clad drawer fronts • Concealed hinges with 6-way adjustment and Soft Close damper • 5/8" thick plywood drawers with Polar White (AAW) full-extension Soft Close runners • Full Overlay door style – decorative hardware required

4 Ships in 2-3 Days! Express Select Door Styles

Elice - Birch Available Colors:

• 3/4" thick x 3" wide solid birch Shaker frame doors with birch veneer over MDF recessed center panels • 3/4" thick birch veneer over MDF flat panel drawer fronts with solid birch edging Mocha (EMG) • Concealed hinges with 6-way adjustment and Soft Close damper • 5/8" thick plywood drawers with full-extension Soft Close runners • Full Overlay door style – decorative hardware required

Cumin (ECN)

Elice - Painted MDF Available Colors:

• 3/4" thick x 3" wide solid MDF Shaker frame doors with 5/8" thick solid MDF recessed center panels • 3/4" thick solid MDF flat panel drawer fronts • Concealed hinges with 6-way adjustment and Soft Close damper Polar White (EPW) • 5/8" thick plywood drawers with full-extension Soft Close runners • Full Overlay door style – decorative hardware required

Salerno - Painted MDF Available Colors:

• 3/4" thick solid MDF flat panel doors • 3/4" thick solid MDF flat panel drawer fronts • Concealed hinges with 6-way adjustment and Soft Close damper • 5/8" thick plywood drawers with full-extension Soft Close runners Polar White (SPW) • Full Overlay door style – decorative hardware required

5 Ships in 7-10 Days! Special Order Door Styles

Monaco - Laminate The styles on this page are available in the following DESIGNER SERIES and ARCHITECT SERIES colors:

DESIGNER SERIES

Bianco (BO) Almond (AL)

Available in both Designer and Architect Series

• 3/4" thick particleboard fl at panel doors with durable thermo- fused melamine fi nish

• 3/4" thick particleboard fl at panel drawer fronts with durable Cognac (CC) Cherry (CH) thermo-fused melamine fi nish • Edges sealed with color-matched PVC edge banding • Concealed hinges with 6-way adjustment and Soft Close damper • Full Overlay door style – decorative hardware required

Espresso (ES) Genoa - Laminate ARCHITECT SERIES

3D 3D texture texture Glacier (GL) Beach (BE)

Available in both Designer and Architect Series

• 3/4" thick particleboard fl at panel wall and base doors with durable thermo-fused melamine fi nish • 3/4" thick particleboard fl at panel drawer fronts with durable thermo-fused melamine fi nish • Edges sealed with color-matched PVC edge banding 3D 3D • Concealed hinges with 6-way adjustment and Soft Close damper texture texture • Full Overlay door style includes integrated brushed nickel pulls Platinum (PL) Twilight (TW) 6 Ships in 7-10 Days! Special Order Door Styles

Dolomiti - Laminate • 3/4" thick wrapped MDF frame with The styles on this page recessed melamine faced MDF are available in the center panel following DESIGNER • 3/4" thick wrapped MDF frame SERIES colors: drawer fronts with recessed melamine faced MDF center panel • Concealed hinges with 6-way adjustment and Soft Close damper • Full Overlay door style – decorative hardware required

2⅜"

¾" Bianco (BO) ¼" Pillow Top Profile

Livorno - Laminate • 3/4" thick wrapped MDF frame doors with recessed melamine faced MDF center panel • 3/4" thick wrapped MDF frame drawer fronts with recessed melamine faced MDF center panel Almond (AL) • Concealed hinges with 6-way adjustment and Soft Close damper • Full Overlay door style – decorative hardware required

2⅜"

¾" Cognac (CC) ¼" Shaker Profile

• 7/8" thick wrapped MDF frame doors Verona - Laminate with recessed melamine faced MDF center panel • 7/8" thick wrapped MDF frame drawer fronts with recessed melamine faced MDF center panel Cherry (CH) • Concealed hinges with 6-way adjustment and Soft Close damper • Full Overlay door style – decorative hardware required

2⅞"

⅞" Espresso (ES) ¼" Beaded Profile 7 Quick Assembly Cabinet Construction

END PANELS INTERIOR 3/4" thick FINISH plywood, Natural birch unfi nished veneer with birch veneer durable exterior* clear coat

ADJUSTABLE BACK PANEL SHELVES 3/16" thick 3/4" thick plywood plywood

Cabinets are packed fl at in

FIXED SHELVES INSTALLATION RAILS Ready-to-Assemble (RTA) kits: 3/4" thick plywood 3/4" thick plywood, dowelled in with hardwood place behind back panel dowels

BACK BEAM 3/4" thick plywood, grooved Quality Construction to capture back panel All RTA Kitchen & Bath Cabinets END FRONT BEAM PANELS feature all-plywood construction 3/4" thick plywood 3/4" thick plywood, unfi nished ADJUSTABLE birch veneer SHELVES exterior* 3/4" thick plywood Easy to Build BACK PANEL Pre-inserted dowels and sturdy 3/16" thick plywood 2" long assembly screws

Easy Door Mount Concealed door hinges include FIXED SHELVES 3/4" thick plywood Soft Close and a clip on/off feature with hardwood dowels

For assembly instructions go to: www.AssemblySheet.com

DRAWER BOX DOOR HINGES SIMPLE 5/8" thick plywood with 3/16" Concealed 6 way ASSEMBLY thick plywood captured adjustable clip on/ All screw holes are bottom panel. Full Extension off with Soft Close pre-drilled with Soft Close runners.** damper.** precise alignment.

*Matching End Panels are available to cover exposed ends **Soft Close feature not available in Wall Angle Corner and Easy Reach Base cabinets

5 Year Manufacturer Warranty

8 Specifications subject to change without notice. Color Matched Finished Ends

WALL All cabinet exterior sides are unfinished birch veneer. Exposed sides, which will be visible after installation, will require a Finished End panel. These panels are FINISHED CABINET END TOP VIEW 3/4" thick with matching finish on both faces and all four edges. Please make allowances for this additional thickness when designing! DOOR

Wall Finished Ends are 13" wide which will extend beyond the front edge of 12" deep wall cabinets, flush with the face of the door. They can be scribed back to the depth of the cabinet if desired. Wall Finished Ends are available 30" high and 38" high.

Base Finished Ends are 25" wide x 34½" high, which will extend beyond the front edge of 23-7/8" deep base cabinets, flush with the face of the door. They can be scribed back to the depth of the cabinet if desired. You can choose to run the matching toe kick into the Finished End, or you can notch the base in order to run the toe kick in front of the panel.

Tall Finished Ends are 25" wide, which will extend beyond the front edge of 23-7/8" deep pantry cabinets, flush with the face of the doors. They can be scribed back to the depth of the pantry cabinet if desired. You can choose to run the matching toe kick into the Finished End, or you can notch the base in order to run the toe kick in front of the panel. Tall Finished Ends are available in 84" high and 92" high.

Other Uses: Because the Finished Ends are 3/4" thick with finished edges, they can be used for other applications, such as open shelving, or to clad the underside of wall cabinets to cover the generic natural birch finish. 9 Wall Cabinets

18" High Double Door WALL CABINET CODING W3018 STANDARD (12" DEEP) W 30 30 30" 12"

Cabinet Cabinet Cabinet Code Width Height 18" · Standard wall cabinets are 12" (305 mm) deep. · Add door thickness for total cabinet depth · Standard cabinet exterior is unfi nished veneer, exposed sides require Finished Ends · All cabinet interiors are natural birch veneer · See page 30 & 31 for items required to assemble - No adjustable shelf each cabinet model

12" High Double Door 21" High Double Door W3012 W3021 W3612 W3621 30", 36" 12" 30", 36" 12"

12" 21"

- No adjustable shelf - One ¾" thick plywood adjustable shelf

15" High Double Door 24" High Double Door

W3015 30" 12" W3024

30" 12"

15" 233/4"

- No adjustable shelf - One ¾" thick plywood adjustable shelf

10 Wall Cabinets

30" High Single Door 30" High Wall Pull-down Shelves Frosted

W1230 24" 12" W2430-PDSFR 12", 15", 18" 12" W1530 W1830 - Features 5 removable acrylic storage bins - Lowers items 10" and 30" brings forward 14¾" 30" - Gas assisted mechanism smoothly raises and lowers unit - Install at desired height in cabinet

- Two ¾" thick plywood adjustable shelves - Can be assembled with hinges on left or right

30" High Double Door 38" High Single Door

W2430 12", 15", 18" 12" W1238 24", 30", 36" 12" W3030 W1538 W3630 W1838

38" 30"

- Two ¾" thick plywood adjustable shelves - Three ¾" thick plywood adjustable shelves - Can be assembled with hinges on left or right

30" High Wall Pull-down Shelves Chrome 38" High Double Door

W2430-PDSCR 12" W2438 24" 12" 24", 30", 36" W3038 - Two tier chrome W3638 shelves lowers 10" and brings items forward 14¾"

30" - Gas assisted 38" mechanism smoothly raises and lowers unit - Locking arm feature holds shelf in down position - Install at desired height in cabinet - Three ¾" thick plywood adjustable shelves

11 Wall Cabinets

38" High Wall Pull-down Shelves Chrome 30" High Wall Angle Corner

24" 24" 12" W2438-PDSCR WAC2430

- Two tier chrome shelves lowers 10" and brings items forward 14¾" 30" - Gas assisted 38" mechanism smoothly raises and lowers unit - Locking arm feature holds shelf in down position 12" - Install at desired height in cabinet - Two ¾" thick plywood adjustable shelves - Can be assembled with hinges on left or right - Clipped back corner provides clearance for installation - SOFT CLOSE DOOR NOT AVAILABLE

38" High Wall Pull-down Shelves Frosted 38" High Wall Angle Corner

24" 12" W2438-PDSFR 24" WAC2438

- Features 5 removable acrylic storage bins 38" - Lowers items 10" 38" and brings forward 14¾" - Gas assisted mechanism smoothly raises and lowers unit 12" - Install at desired height in cabinet - Three ¾" thick plywood adjustable shelves - Can be assembled with hinges on left or right - Clipped back corner provides clearance for installation - SOFT CLOSE DOOR NOT AVAILABLE

ready-to-assemble design tip Compliment our solid-color slab door and drawer fronts with contrasting color or texture.

Combine white or almond cabinetry with wood grain trims and finished panels to add interest and texture.

12 Wall Cabinet Trim Items

Range Hood Combo Kit - Straight Valance Wall Finished Ends

17.38" WRHC36S WFE1330A WFE1338A

9.69" - Available 36" width - 3/4" thick plywood for CN, 31" 19.32" - Includes Hood, Chimney, MG, and PW Trimmable Hood Liner and Blower 10.84" - 3/4" thick melamine faced - Chimney is trimmable to 30" particleboard all other colors adjust the height or 38" - Matching finish 2 sides and - Blower is 390 CFM, 6.0 all 4 edges sones, enclosed light - Use to cover exposed sides 22.88" - Available in CN, MG of wall cabinets 36" and PW only 19" - Field modified and installed - Clearance of 3" on each 38.31" side is recommended - Loose matching edge tape 20.08" included 13"

Filler Strips ¾" Scribe Molding

F330A SM96A F338A

30" F630A 38" 8' ¼" F638A ¾"

3" or 6"

- 3/4" thick solid wood for CN and MG - 3/4" thick MDF painted for PW - 1/4" thick solid wood - 3/4" thick melamine faced particleboard all other colors - Available in AL, CN, MG and PW only - Face and two long edges finished * See pg. 23 for addtional trim moldings

Wall Cabinet Framing Strip Outside Corner Molding TKFS96A OSC8 ¾" ¾" 8' 96" ¼" ¾"

4½"

- 3/4" thick plywood for CN, MG and PW - 3/4" thick solid wood - 3/4" thick melamine faced particleboard all other colors - Available in AL, CN, MG and PW only - Install above or below wall cabinets flush with front edge * See pg. 23 for addtional trim moldings of finished ends - Face and two long edges finished - 24" of loose matching edge tape included 13 Base Cabinets

Single Door with 1 Drawer and 1 Roll-Out Tray BASE CABINET CODING B 18 - 2T 15", 18" B15-1T 7 23 ü8" B18-1T

Cabinet Cabinet Customization Code Width (2ROTS)

· Standard Base Cabinets are 23-7/8" (605 mm) deep and 34½" high 34½" · Add door thickness for total cabinet depth · All drawers feature Full-Extension Soft Close drawer runners · Standard cabinet exterior is unfi nished veneer, exposed sides require Finished Ends - Can be assembled with hinges on left or right · All cabinet interiors are natural birch veneer - One half depth adjustable shelf · See page 28 & 29 for items required to assemble - One adjustable roll-out tray with Full-Extension runners each cabinet model

Single Door Base with 1 Drawer Single Door with 1 Drawer & 1 Wire Roll-Out Tray

15", 18" B12 7 B15-1WT 23 �8" 12", 15", 18" 7 23 �8" B15 B18-1WT B18

34½" 34½"

- Can be assembled with hinges on left or right - Can be assembled with hinges on left or right - One half depth adjustable shelf - One full width chrome wire rollout tray - Features Full-Extension runners

Single Door with 1 Drawer & Chrome Tray Divider Single Door with 1 Drawer & 2 Roll-Out Trays

12" 7 B12-TD 15", 18" B15-2T 23 �8" 7 23 ü8" B18-2T

34½" 34½"

- Can be assembled with hinges on left or right - Can be assembled with hinges on left or right - Chrome wire divider - Two adjustable roll-out trays with Full-Extension runners 14 - Divider is 3"W x 9-7/8"H x 11¾"D Base Cabinets

Single Door Base with 1 Drawer & 2 Wire Double Door with 1 Drawer & 1 Roll-Out Tray Roll-Out Trays

15", 18" 24" 7 B15-2WT B24-1T 23 �8" 23-7/8" B18-2WT

34½" 341/2"

- One full width drawer with two drawer fronts - Can be assembled with hinges on left or right - One half depth adjustable shelf - Two chrome finish wire roll-out trays - One adjustable roll-out tray with Full-Extension runners - Features Full-Extension runners

Single Door with 1 Drawer & 2 Tier Double Door with 1 Wire Roll-Out Tray Cookware Organizer 24" B15-CWO 7 B24-1WT 15" 23 �8" 7 23 �8"

34½" 34½"

- Can be assembled with hinges on left or right - One full width chrome wire roll-out tray - Two chrome wire tiers operate independently - Features Full-Extension runners - Adjustable dividers accomodate different size cookware

Double Door with 1 Drawer Double Door with 1 Drawer & 2 Roll-Out Trays

B24 24" B24-2T 24", 30", 36" 7 23-7/8" 23 �8" B30 B36

341/2" 34½"

- One full width drawer with two drawer fronts - One full width drawer with two drawer fronts - One half depth adjustable shelf - One half depth adjustable shelf - Two adjustable roll-out trays with Full-Extension runners 15 Base Cabinets

Double Door with 1 Drawer & 2 Wire Roll-Out Trays Single Door with 1 Drawer & Single Waste Basket Pull-Out 24" 7 B24-2WT B15-SWB 23 �8" 15", 18" 7 23 �8" B18-SWB

34½" 34½"

- Can be assembled with hinges on left or right - Door mount kit included to mount cabinet door - Two full width chrome wire roll-out trays to waste container - Features Full-Extension runners - Features Full-Extension Soft Close ball-bearing slides - 35 quart container is removable for easy cleaning

Double Door with 1 Drawer & 2 Tier Single Door with 1 Drawer & Double Cookware Organizer Wastebasket Pull-out B24-CWO B15-DWB 24" 15", 18" 7 7 23 �8" 23 �8" (2) 27QT B18-DWB (2) 35QT

34½"

34½"

- Can be assembled with hinges on left or right - Door mount kit included to mount cabinet door to waste container - Two chrome wire tiers operate independently - Features Full-Extension Soft Close ball-bearing slides - Adjustable dividers accomodate different size cookware - Removable containers for easy cleaning

Base with 3 Drawers Sink Base

12", 15", 18", 30" 7 BD12 SB30 8 23 � " 30", 36" 7 BD15 23 �8" SB36 6" BD18 BD30 12" 34½" 34½"

12"

- One standard top drawer - No shelf, two false drawer fronts - Two deep drawers - May also be used as drop-in cook top base 16 - All Full-Extension runners Base Cabinets

Deluxe Sink Base with Shelf Liner Deluxe Sink Base with 2 U-Shape Pull-Outs

SB30-SL SB36-2USWP 30", 36" 23 7�8" 36" 7 SB36-SL 23 �8"

1 34 /2" 34½"

- No shelf, two false drawer fronts - No shelf, two false drawer fronts - Liner helps protect cabinet from damage due to leaks in pipes or drain - Two full-width chrome wire U-shaped pull-out baskets fit around plumbing under sink - Grey polystyrene easy to clean surface

Sink Base with Pull-Out Caddy 36" x 36" Easy Reach Corner

SB30-POC Corner of wall EZR36 7 " 30", 36" 23 �8" 36 3" void SB36-POC 33"

34½" 341/2"

- No shelf, two false drawer fronts - Can be assembled with hinges on left or right - One removeable chrome wire caddy 11¼"W x 19¼"H x 16¼"D - One half depth “L” shaped shelf - Adjustable handle works around plumbing and - Doors open 170 degrees for easy access other obstructions - SOFT CLOSE DOOR NOT AVAILABLE

Deluxe Sink Base with U-Shape Pull-Out 36" x 36" Easy Reach Corner with 2 Wire Lazy Susans

Corner of wall

36" 7 23 �8" 36" SB36-1USWP 3" void EZR36-2WLS 33"

34½" 341/2"

- No shelf, two false drawer fronts - Can be assembled with hinges on left or right - One full-width chrome wire U-shaped pull-out baskets - Two 28" kidney shaped chrome lazy susan shelves fit around plumbing under sink - Doors open 170 degrees for easy access - SOFT CLOSE DOOR NOT AVAILABLE 17 Base Cabinets

Blind Corner Base Base Finished End

42" 36" 7 23 �8" BBC42 BFE2534A

- 3/4" thick plywood for CN, MG, and PW 34½" 34½" - 3/4" thick melamine faced particleboard all other colors - Matching finish 2 sides and all 4 edges - Field modified and installed - 35" of loose matching edge tape included 25" - Can be assembled with blind on left or right (right shown) ¾" - Cabinet can be pulled for exact fit (42"-45") - One half depth adjustable shelf - 21" wide blind closure panel included - 6" filler and 3" return filler included Toe Kick / Tall Filler Strip

Blind CornerBlind Corner Base Base Cabinet Installation • Comes with 24" wide panel - 18" panel and 6" profiled filler TKFS96A • Cabinets widths exact - add 3" for pull clearance ¾" • Blind left shown 42" 36" 96"

BLIND CORNER BASE BLIND 21"24" LEFT 15"18" 6"6" 15" SHOWN OPEN SPACE

OPEN SPACE 4½"

3" return filler - 3/4" thick plywood for CN, MG and PW

BASE TOP VIEW - 3/4" thick melamine faced particleboard all other colors CABINET - Face and two long edges finished - 24" of loose matching edge tape included - Available in all finishes

Filler Strips Rollout Tray Kits F330A ROTK15 3" F630A ROTK18 4 ROTK24

- 3/4" thick solid wood for CN and MG 4" - 3/4" thick MDF painted for PW 20" 30" - 3/4" thick melamine faced particle board all other colors - Face and two long edges finished - Available in all finishes - Full-Extension Soft Close undermount runners - To fit 15", 18" and 24" wide base cabinets - 5/8" thick plywood construction with screw assembly - 3/16" thick plywood captured bottom 3" or 6" - Natural birch veneer finish 18 Base Cabinets

Island Skin ISK4848 ready-to-assemble design tip - 3/16" thick matching exterior - Field modified and installed 48" - Available in all finishes - CN and MG are veneer faced plywood - PW is painted plywood - All other colors are melamine over MDF

48"

Island V-Groove Skin IVGSK4848 Our fi nished end panels are 3/4" thick, - 3/16" thick wood veneer v-groove exterior so adding them to - Grooves spaced 1¼" unfi nished sides can on center sometimes throw off 48" - Field modified and installed alignment of uppers - Available in CN, MG and to bases. Balance PW only out wall and base alignment with fi llers used as 'spacers' to

48" keep wall and base measurements even.

ready-to-assemble design tip Use a Toe Kick/Framing Strip (TKFS96) to trim out the tops and bottoms of wall cabinets. Align the face of the framing strips with the face of Wall Finished End Panels for a truly "inset" appearance.

19 Tall Cabinets

84" high Two Door Pantry with 4 Roll-out Trays PANTRY CABINET CODING 18" 7 P182484-4T 23 �8" P 18 24 84

- Can be assembled with Cabinet Cabinet Cabinet Cabinet hinges on left or right Code Width Depth Height - One fixed and four adjustable shelves · Standard Pantry Cabinets are 23-7/8" deep 84" - Four rollout trays · Add door thickness for total cabinet depth - Exposed sides require TFE2584 · Standard cabinet exterior is unfinished veneer, exposed sides require Finished Ends NOTE: Lower door in Madrid · All cabinet interiors are natural birch veneer and Grenada styles is (2) · See page 30 & 31 for items required to build each model panels joined together

84" high Two Door Pantry 84" high Two Door Pantry with 4 Wire Shelf Pull-Outs

P182484 18" 7 P182484-4WS 18" 23 �8" 7 23 �8" - Can be assembled with hinges on left or right - One fixed and two adjustable shelves - Can be assembled with hinges - Slide-out unit includes 4 on left or right chrome baskets and optional door mounts 84" 84" - One fixed and four adjustable shelves - Top and bottom glides are soft closing and 250 lb. - Optional rollout trays available weight rated - Exposed sides require TFE84 - Exposed sides require TFE2584 NOTE: Lower door in Madrid and Grenada styles is (2) NOTE: Lower door in Madrid panels joined together and Grenada styles is (2) panels joined together

84" high Two Door Pantry with 2 Roll-out Trays 92" high Two Door Pantry

18" 18" 7 P182484-2T 7 P182492 23 �8" 23 �8"

- Can be assembled with hinges on left or right - Can be assembled with - One fixed and four hinges on left or right adjustable shelves - One fixed and four adjustable shelves - Optional rollout trays 84" 92" available - Two rollout trays - Exposed sides require - Exposed sides require TFE2592 TFE2584 NOTE: Lower door in NOTE: Lower door in Madrid and Grenada Madrid and Grenada styles styles is (2) panels joined is (2) panels joined together together 20 Tall Cabinets

92" high Two Door Pantry with 2 Roll-out Trays Rollout Tray Kits

18" 7 P182492-2T ROTK18 23 �8"

- Can be assembled with hinges on left or right 4" - One fixed and four 20" adjustable shelves 92" - Two rollout trays - Exposed sides require TFE2592 - Full-Extension Soft Close undermount runners - Fits 18" wide base and tall cabinets NOTE: Lower door in Madrid and Grenada styles is (2) - 5/8" thick plywood construction with screw assembly panels joined together - 3/16" thick plywood captured bottom - Natural birch veneer finish

92" high Two Door Pantry with 4 Roll-out Trays Tall Filler Strip 18" P182492-4T TKFS96A 7 23 �8" ¾"

- Can be assembled with - 3/4" thick plywood for CN, hinges on left or right MG and PW - One fixed and four - 3/4" thick melamine faced adjustable shelves particleboard all other colors - Four rollout trays - Face and two long edges 92" finished - Exposed sides require TFE2592 96" - 24" of loose matching edge tape included NOTE: Lower door in Madrid and Grenada styles is (2) panels joined together

4½"

92" high Two Door Pantry with 4 Wire Shelf Pull-Outs Tall Finished End

18" 7 23 �8" P182492-4WS TFE2584A - Can be assembled with TFE2592A hinges on left or right - One fixed and two - 3/4" thick plywood for CN, adjustable shelves MG, and PW - Slide-out unit includes 4 - 3/4" thick melamine faced chrome baskets and optional 84" particleboard all other door mounts colors 92" or - Top and bottom glides are 92" - Matching finish 2 sides soft closing and 250 lb. and 4 edges weight rated - Field modified and - Exposed sides require installed TFE2592 - 84" or 92" of loose matching edge tape NOTE: Lower door in Madrid included and Grenada styles is (2) panels joined together 25" 21 Vanity Base Cabinets

Vanity Sink Base with Pivot Waste Bin VANITY CABINET CODING VSB3021-PWB 30", 36" 21" VSB3621-PWB VSB 30 21

Cabinet Cabinet Cabinet Code Width Depth

341/2"

· Standard Vanity Base Cabinets are 21" deep and 34½" high · Add door thickness for total cabinet depth · Standard cabinet exterior is unfinished veneer, exposed sides require Finished Ends · All cabinet interiors are natural birch veneer - No shelf, two false drawer fronts - 15 liter pivot-out waste bin · See page 30 & 31 for items required to build each model - Pivot-out design opens lid when cabinet door is opened - Features an inner polymer container with handle for easy removal

Vanity Sink Base Vanity Base with 3 Drawers VSB2421 VBD1221 12", 15" 24", 30", 36" 21" VSB3021 21" VBD1521 VSB3621 6"

12" 1 341/2" 34 /2"

12"

- No shelf, two false drawer fronts - One standard top drawer - Two deep drawers

Vanity Sink Base with Liner Two Door Linen Cabinet

VSB2421-SL 18" L182184 24", 30", 36" 21" VSB3021-SL 21" VSB3621-SL

- Can be assembled with hinges on left or right 1 34 /2" - One fixed and four adjustable shelves 84" - Exposed sides require TFE2584 (trimmed on site)

NOTE: Lower door in - No shelf, two false drawer fronts Madrid and Grenada styles - Liner helps protect cabinet from damage due to leaks is (2) panels joined together in pipes or drain - Grey polystyrene easy to clean surface 22 Decorative Moldings

Crown Molding Classic Crown Molding CM96A CCM8

8' 2 5/ 8 " 8'

3" 1" x 2"TMMS8 3 5/ 8 "

¾" 1" x 2"

Framing Finished Strip End Framing Finished Strip End

- 3/4" thick solid wood - 3/4" thick solid wood - Install at top of Framing Strip - Install at top of Framing Strip - Recommended Top Molding Mounting Strip TMMS8 (pg. 24) - Recommended Top Molding Mounting Strip TMMS8 (pg. 24) - Available in CN, MG and PW only - Available in CN, MG and PW only

Angle Crown Molding Dentil Molding ACM8 DM8

8'

5 2 / 8 " 1" x 2" 8' ½"

5/8" Framing Finished Strip End

- 3/4" thick solid wood - 3/4" thick solid wood - Install at top of Framing Strip - Available in CN, MG and PW only - Recommended Top Molding Mounting Strip TMMS8 (pg. 24) - Available in CN, MG and PW only

Soffit Crown Molding Rope Molding SCM8 RM8

8' 9 1 / 16 " 8' 5/8 9 1" x 2" " 1 / 16 "

3/8" Framing Finished Strip End

- 3/4" thick solid wood - 3/4" thick solid wood - Install at top of Framing Strip - Available in CN, MG and PW only - Recommended Top Molding Mounting Strip TMMS8 (pg. 24) - Available in CN, MG and PW only 23 Decorative Moldings

Top Molding Mounting Strip Light Rail TMMS8 LR96A

½" Mounting Strip ¾" 8' 8'

¾" 2¼" Molding 13 /16 " ¾" - Solid wood - Install along bottom framing strip of wall cabinets - 3/4" thick solid wood - Available in CN, MG and PW only - Can be used with ACM8, CM96A, CCM8 and SCM8 - BO, CC, CH, and ES available in Wrapped Universal Light Rail (ULR96), see below

Wrapped Cove Molding Wrapped Universal Light Rail CVM96A ULR96

1" 1½"

2¼" 3¼"

¾" ¾" 3" - 96" in length - 96" in length - Laminate wrapped MDF core - Laminate wrapped MDF core - Includes under-mount installation leg - Includes top-mount installation leg - Available in BO, CC, CH, and ES colors - Available in AL, BO, CC, CH, and ES colors - CN, MG, PW Available in Light Rail (LR96A), see above

Beaded Light Rail Valance BLR8 VA48 ¾" 8' 48" 2"

1" 3"

- 1" thick solid wood - 3/4" thick solid wood - Install along bottom framing strip of wall cabinets - May be trimmed on each end - Available in CN, MG and PW only - Available in CN, MG and PW only

24 Decorative Moldings

Corbel Wood Outside Corner Molding CBL OSC8

6 1 / 16 " 5¾" ¾" 8' ¼" 8 7 / 8" ¾"

- 3/4" thick solid wood - Available in AL, CN, MG and PW only - Solid hardwood - BO, CC, CH, and ES colors are available - Available in CN and MG only in Wrapped Outside Corner Molding (OC96A), see below

Wood Scribe Molding Wrapped Outside Corner Molding SM96A OC96A ¼"

8' ¼" ¾" 1" ¾"

1"

- 96" in length - 1/4" thick solid wood - Paper laminate wrapped MDF core - Available in AL, CN, MG and PW only - Available in BO, CC, CH, and ES colors - BO, CC, CH, and ES are available in Wrapped Scribe - AL, CN, MG and PW available in Wood Outside Corner Molding (SCR96A), see below Molding (OSC8), see above

ready-to-assemble Wrapped Scribe Molding SCR96A design tip

5 /16"

11/8"

- 96" in length - Laminate wrapped MDF core Use Wall Finished End (WFE) or Tall Finished End - Available in BO, CC, CH, and ES colors (TFE) panels to clad the underside of cabinets - AL, CN, MG and PW available in Wood Scribe that will be visible at standing height instead of Molding (SM96A), see above a Toe Kick/Framing Strip (TKFS96). 25 Decorative Moldings

Wood Inside Corner Molding Wood Batten Molding ICM8 BM8

8' ¾" 8' ¼" ¾" ¾"

- 3/4 thick solid wood " - 1/4" thick solid wood - Available in CN, MG and PW only - Available in CN, MG and PW only - BO, CC, CH, and ES colors are available in Wrapped Inside Corner Molding (IC96A), see below

Wrapped Inside Corner Molding Wood Furniture Base Molding IC96A FBM8

3/16"

¾" 8'

¼" 4" 3½"

¾" ¾"

- 96" in length - Paper laminate wrapped MDF core - Available in BO, CC, CH, and ES colors - 3/4" thick solid wood - CN, MG and AW is available in Wood Inside - Available in CN, MG and PW only Corner Molding (ICM8), see above

Wood Quarter Round Decor•Edge Color Matched Cabinet Edging - 25ft. Roll QR8 PSEB-25

8' ¾"

¾"

¾"

- 3/4" thick solid wood - Available in CN, MG and PW only - Apply over cabinet front edge banding to color match door finish - Simple peel & stick application - Available in all finishes 26 Interior Accessories

24" Pull-down Shelves Chrome Single 35 Qt. Pull-out Waste Bin Kit PDWSS24-CR PWBK-S35-GR

- Install in 24 "x 30" - Install in 15" and 24" x 38" wall base cabinet cabinets - Door mount kit - Two tier chrome included to mount 18¼" shelves lowers 10" cabinet door and brings items forward 14¾" 18 7�8" - Features Full- Extension Soft Close - Gas assisted ball-bearing slides mechanism smoothly raises and lowers unit - 35 quart container is removable for 10" 22¼" - Locking arm feature 22" easy cleaning holds shelf in down position 10 3�8"

NOTE: 30" minimum cabinet height required NOTE: Not for use in vanity depth cabinets

24" Pull-down Shelves Frosted PDWSS24-FR Double Pull-out Waste Bin Kit PWBK-D27-GR PWBK-D35-GR

- Install in 24 "x 30" - D27 fits 15" base and 24" x 38" wall cabinet with (2) 27 qt. cabinets containers 21½" - Features 5 removable - D35 fits 18" base cabinet with (2) 35 qt. acrylic storage bins 7 18 �8" containers - Lowers items 10" and brings forward 14¾" - Door mount kit included to mount - Gas assisted cabinet door mechanism smoothly 22" - Features Full- raises and lowers unit 1�8" 10½" 22¼" 11 7�8", 14 Extension Soft Close - Locking arm feature ball-bearing slides holds shelf in down position - Removable NOTE: Not for use in containers for easy vanity depth cabinets cleaning underneath NOTE: 30" minimum cabinet height required

Pantry Pull-out 4 Chrome Wire Shelves Undersink Pull-out Caddy Kit USPCK12-CR 19½" PP4WS18-CR - Adjustable handle that - 250lbs. weight rated slides either direction slide system to work around plumbing or other - Ball Bearing Top Slide obstructions - Basket height: 4" - Completely removable - Door mount 19¼" to take cleaning 43½"-50¾" kit included products with you - Leak proof trays

NOTE: Not for use in 16¼" vanity depth cabinets 11¼"

14¾" 27 Interior Accessories

2-Tier Cookware Organizer for 15" Base Single Wire Roll-out Tray for 24" Base

2TCWO15-CR SWROT24-CR

- Adjustable dividers 6 5�8" to accommodate 18 1�8" different sizes of cookware 22" - Bottom, side and 20 3�8" 22" rear mount for total stability 11 5�8" - Heavy-gauge wire - Full-extension 100lb. rated ball-bearing slides construction - Fully-assembled and simple 4 screw installation - Two tiers operate independently - Heavy-gauge wire construction

NOTE: Not for use in vanity depth cabinets NOTE: Not for use in vanity depth cabinets

2-Tier Cookware Organizer for 24" Base Double Wire Roll-out Tray for 15" & 18" Base 2TCWO24-CR DWROT15-CR DWROT18-CR

- Adjustable dividers to accommodate 5" different sizes of - Bottom, side and cookware rear mountin for total stability - Bottom, side and 19" - Heavy-gauge wire 18 1�8" rear mount for total stability construction - Heavy-gauge wire - Two tiers operate independently 22" construction 22" - Two tiers operate 5�8" 20 5 8" independently 5 14 � 11 �8",

NOTE: Not for use in vanity depth cabinets NOTE: Not for use in vanity depth cabinets

Single Wire Roll-out Tray for 15" & 18" Base Double Wire Roll-out Tray for 24" Base

SWROT15-CR DWROT24-CR SWROT18-CR

5" - Full-extension - Bottom, side and 100lb. rated ball- rear mountin bearing slides 19" 6 5�8" for total stability - Fully-assembled - Heavy-gauge wire and simple 4 construction 22" screw installation 3�8" 22" - Two tiers operate 11 3�8", 14 - Heavy-gauge wire 5 8" independently construction 20 �

NOTE: Not for use in vanity depth cabinets NOTE: Not for use in vanity depth cabinets 28 Interior Accessories

Undersink U-shaped Wire Pull-out Shelf 15 Liter Pivot Waste Bin

USWPK36-CR RPOVWB15L

4¼" - Perfect for vanity or kitchen 5 5 �8" applications - Pivot-out design opens lid when 21¾" 15½" cabinet door is 32½" opened - Chrome finish - Features an inner 10½" polymer container - Fits in 36" cabinet with handle for - Fits around obtrusive plumbing under the kitchen sink easy removal

NOTE: Not for use in vanity depth cabinets

Double Wire Lazy Susan Kit - Chrome Kitchen Sink Base Liner DWLSK-CR SBL2730 SBL3336

2¾" 23¼" 17 7�8" 28½", 34½"

- Helps protect sink cabinet from damage due to leaks 28" in piping or drains - SBL2730 can be trimmed to fit SB30 - 2-Shelf 28" Kidney Shape Chrome Lazy Susans - SBL3336 can be trimmed to fit SB36 - Fits inside EZ36 Base Cabinet (page 17) - Not for use in vanity base cabinets - Chrome 2-Shelf Set with telescoping shaft - Grey polystyrene wipes clean with ease - Heavy-gauge wire construction

U-Shaped Tray Divider 3" - Chrome Vanity Sink Base Liner

USTD3-CR VSBL2124 VSBL2730 VSBL3336 - Bakeware Organizer 20¼" - Simple installation 22½", 28½", 34½" with only 4 screws 9 7�8" - Use 2 or more to organize cabinet 11¾" - Can be used - Helps protect sink cabinet from damage due to leaks in base or wall in piping or drains 3" cabinet - VSBL2124 can be trimmed to fit VSB2421 - VSBL2730 can be trimmed to fit VSB3021 - VSBL3336 can be trimmed to fit VSB3621 - Grey polystyrene wipes clean with ease 29 Required Items List

Wall Cabinets Pantry Cabinets Model Required Items Model Required Items W3012 1 x W3012 Cabinet Kit P182484 1 x P84EP End Panel Pack 1 x Door Pack Q 1 x P1824SP Shelf Pack W3612 1 x W3612 Cabinet Kit 1 x Door Pack D 1 x Door Pack R 1 x Door Pack P W3015 1 x W3015 Cabinet Kit P182484-2T 1 x P84EP End Panel Pack 1 x Door Pack S 1 x P1824SP Shelf Pack W3018 1 x W3018 Cabinet Kit 1 x Door Pack D 1 x Door Pack T 1 x Door Pack P W3021 1 x W3021 Cabinet Kit 2 x ROTK18 Tray Kit 1 x Door Pack U P182484-4T 1 x P84EP End Panel Pack W3621 1 x W3621 Cabinet Kit 1 x P1824SP Shelf Pack 1 x Door Pack V 1 x Door Pack D W3024 1 x W3024 Cabinet Kit 1 x Door Pack P 1 x Door Pack W 4 x ROTK18 Tray Kit W1230 1 x W1230 Cabinet Kit P182492 1 x P92EP End Panel Pack 1 x Door Pack A 1 x P1824SP Shelf Pack W1530 1 x W1530 Cabinet Kit 1 x Door Pack H 1 x Door Pack B 1 x Door Pack P W1830 1 x W1830 Cabinet Kit P182492-2T 1 x P92EP End Panel Pack 1 x Door Pack D 1 x P1824SP Shelf Pack W2430 1 x W2430 Cabinet Kit 1 x Door Pack H 2 x Door Pack A 1 x Door Pack P W3030 1 x W3030 Cabinet Kit 2 x ROTK18 Rollout Tray Kit 2 x Door Pack B P182492-4T 1 x P92EP End Panel Pack W3630 1 x W3630 Cabinet Kit 1 x P1824SP Shelf Pack 2 x Door Pack D 1 x Door Pack H WAC2430 1 x WA2430 Cabinet Kit 1 x Door Pack P 1 x Door Pack C 4 x ROTK18 Rollout Tray Kit W1238 1 x W1238 Cabinet Kit 1 x Door Pack E W1538 1 x W1538 Cabinet Kit 1 x Door Pack F W1838 1 x W1838 Cabinet Kit 1 x Door Pack H W2438 1 x W2438 Cabinet Kit 2 x Door Pack E W3038 1 x W3038 Cabinet Kit 2 x Door Pack F W3638 1 x W3638 Cabinet Kit 2 x Door Pack H WAC2438 1 x WA2438 Cabinet Kit 1 x Door Pack G

30 Required Items List

Base Cabinets Model Required Items Model Required Items B12 1 x B12 Cabinet Kit B30 1 x B30 Cabinet Kit 1 x Door Pack I 2 x Door Pack J BD12 1 x BD12 Cabinet Kit BD30 1 x BD30 Cabinet Kit 1 x Door Pack L 1 x Door Pack O B15 1 x B15 Cabinet Kit SB30 1 x SB30 Cabinet Kit 1 x Door Pack J 2 x Door Pack J B15-1T 1 x B15 Cabinet Kit B36 1 x B36 Cabinet Kit 1 x Door Pack J 2 x Door Pack K 1 x ROTK15 Rollout Tray Kit SB36 1 x SB36 Cabinet Kit B15-2T 1 x B15 Cabinet Kit 2 x Door Pack K 1 x Door Pack J EZR36 1 x EZR36 Cabinet Kit 2 x ROTK15 Rollout Tray Kit 1 x Door Pack EZ B15-SWB 1 x B15 Cabinet Kit BBC42 1 x BBC42 Cabinet Kit 1 x Door Pack J 1 x Door Pack J 1 x PWBK-S35 Waste Bin Kit 1 x F630 Filler Strip B15-DWB 1 x B15 Cabinet Kit 1 x F330 Filler Strip 1 x Door Pack J 1 x PWBK-D27 Waste Bin Kit BD15 1 x BD15 Cabinet Kit Vanity Base Cabinets 1 x Door Pack M B18 1 x B18 Cabinet Kit VSB2421 1 x VSB2421 Cabinet Kit 1 x Door Pack K 2 x Door Pack I B18-1T 1 x B18 Cabinet Kit VSB3021 1 x VSB3021 Cabinet Kit 1 x Door Pack K 2 x Door Pack J 1 x ROTK18 Rollout Tray Kit VSB3621 1 x VSB 3621 Cabinet Kit B18-2T 1 x B18 Cabinet Kit 2 x Door Pack K 1 x Door Pack K VBD1221 1 x VBD1221 Cabinet Kit 2 x ROTK18 Rollout Tray Kit 1 x Door Pack L B18-SWB 1 x B18 Cabinet Kit VBD1521 1 x VBD1521 Cabinet Kit 1 x Door Pack K 1 x Door Pack M 1 x PWBK-S35 Waste Bin Kit L182184 1 x L84EP End Panel Pack B18-DWB 1 x B18 Cabinet Kit 1 x L1821SP Shelf Pack 1 x Door Pack K 1 x Door Pack D 1 x PWBK-D27 Waste Bin Kit 1 x Door Pack P BD18 1 x BD18 Cabinet Kit 1 x Door Pack N B24 1 x B24 Cabinet Kit 2 x Door Pack I B24-1T 1 x B24 Cabinet Kit 2 x Door Pack I 1 x ROTK18 Rollout Tray Kit B24-2T 1 x B24 Cabinet Kit 2 x Door Pack I 2 x ROTK18 Rollout Tray Kit 31 Decorative Hardware

- Euro railing pull - Brushed steel - Brushed nickel - Brushed nickel - Features dual mounting hole options

DH45-100 - 7" Euro Pull DH44-346 - 8" Square Bar Pull DH116-120 - 10" Quadra Pull 3¾" center (96mm) 7½" center (196mm) 5" inside center (128mm) 8-13/16" outside center (224mm) DH44-348 - 9" Square Bar Pull DH45-102 - 10" Euro Pull* 8-13/16" center (224mm) DH116-122 - 11" Quadra Pull 6-15/16" center (176mm) 6-5/16" inside center (160mm)

DH44-350 - 13" Square Bar Pull* 10-1/16" outside center (256mm)

DH45-104 - 13" Euro Pull* 12-5/8" center (320mm) 9¾" center (248mm) DH116-126 - 14" Quadra Pull DH44-352 - 19" Square Bar Pull* 8-13/16" inside center (224mm) 18-7/8" center (480mm) 12-5/8" outside center (320mm)

DH116-134 - 20" Quadra Pull* 15-1/8" inside center (384mm) 18-7/8" outside center (480mm)

DH116-136 - 24" Quadra Pull* 18-7/8" inside center (480mm) 22-11/16" outside center (576mm)

* Due to the overall length of this hardware, it is not compatible with drilling template HDWE TEMPLATE-TK or RTA.

32 Decorative Hardware

DH43-826 DH43-630 DH43-618

- Elongated oval knob - Elongated oval knob - Octagon knob - Antique pewter - Oiled bronze - Oiled bronze - 2" length - 2" length - 1-3/8" diameter

DH43-828 DH43-632 DH43-614

- Classic pull - Classic pull - Traditional pull - Antique pewter - Oiled bronze - Oiled bronze - 3-3/4" center (96mm) - 3-3/4" center (96mm) - 3-3/4" center (96mm) - 4-3/4" outside length - 4-3/4" outside length - 4-1/2" outside length

DH43-824 DH43-628 DH43-628

- 1" Backplate for - 1" Backplate for - 1" Backplate for DH43-828 DH43-632 DH43-614 - Antique pewter - Oiled bronze - Oiled bronze - 3¾" center (96mm) - 3¾" center (96mm) - 3-3/4" center (96mm) - 5¼" outside length - 5¼" outside length - 5-1/4" outside length

DH43-820 DH43-624 DH43-624

- Screw-head cup pull - Screw-head cup pull - Screw-head cup pull - Antique pewter - Oil rubbed bronze - Oil rubbed bronze - 2-1/2" center (64mm) - 2-1/2" center (64mm) - 2-1/2" center (64mm) - 4-1/8" outside length - 4-1/8" outside length - 4-1/8" outside length

DH99-188 DH93-152 DH43-124

- Round knob - Raised mitered knob - Octagon knob - Brushed nickel - Antique pewter - Antique silver - 1-1/4" diameter - 1-3/8" square - 1-3/8" diameter DH99-128 DH93-112 DH43-114

- Contemporary bow pull - Raised mitered pull - Traditional pull - Brushed nickel - Antique pewter - Antique silver - 3-3/4" center (96mm) - 3-3/4" (96mm) & - 3-3/4" center (96mm) - 5-1/4" outside length 5" (128mm) center - 4-1/2" outside length - 6-3/8" outside length 33 Decorative Hardware

DH65-432 DH65-200 DH88-104

- Birdcage knob - Birdcage knob - Arrowhead knob - Stainless steel - Antique iron - Antique pewter - 2-1/2" length - 2-1/2" length - 3-1/2" length

DH65-402 DH65-120 DH88-110

- Birdcage pull - Birdcage pull - Arrowhead pull - Stainless steel - Antique iron - Antique pewter - 3-3/4" center (96mm) - 3-3/4" center (96mm) - 5" center (128mm) - 4" outside length - 4" outside length - 7-1/2" outside length

DH95-144 DH87-102 HDWE TEMPLATE-TK HDWE TEMPLATE-RTA Hardware Drilling Template Align with door frame to quickly and accurately mark hole locations.

- Square dimpled knob - Square ribbed knob - Matte nickel - Brushed nickel - 1-1/4" square - 1" square

DH95-104 DH87-112 11-3/8"

2-7/8"

- Square dimpled pull - Ribbed bow pull NOTE: Refer to the individual - Matte nickel - Brushed nickel decorative hardware size - 6-5/16" center (160mm) - 3-3/4" center (96mm) specifications to determine - 7-1/2" outside length - 4-11/16" outside length 34 compatibility with this template. Notes

35 hdckitchens.com Ready-to-Assemble Kitchen & Bath Cabinetry

Instant Kitchen Cabinet Estimator Quality

Free Color Measuring Samples Guide

5 Year Manufacturer Warranty

HDC-RTA-SPECBOOK-0317