DOCSLIB.ORG

Investigating the Relationship Between Hardness and Yield Strength of Ss400 Steel Using Nanoindentation

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Investigating the Relationship Between Hardness and Yield Strength of Ss400 Steel Using Nanoindentation International Journal of Advances in Mechanical and Civil Engineering, ISSN: 2394-2827 Volume-4, Issue-2, Aprl.-2017 http://iraj.in INVESTIGATING THE RELATIONSHIP BETWEEN HARDNESS AND YIELD STRENGTH OF SS400 STEEL USING NANOINDENTATION 1NGOC-VINH NGUYEN, 2VIET-HUNG TRUONG, 3THAI-HOAN PHAM, 4SEUNG-EOCK KIM 1,2PhD Student, Dept. Of Civil and Environmental Engineering, Sejong University, Seoul, Korea. 3PhD, Dept. Of Civil Engineering, Vinh University, 182 Le Duan, Vinh City, Viet Nam. 4Professor, Dept. Of Civil and Environmental Engineering, Sejong University, 98 Gunja-dong, Gwangjin-gu, Seoul, 143- 747, Korea. E-mail: [email protected], [email protected], [email protected], [email protected] Abstract - In this study, Nano Hardness test was carried out at room temperature with different strain rates from 0.002 s-1 to 0.2 s-1,. A reverse algorithm was used to determine the yield strength from the load-displacement curve of the indentation test. From the obtained yield strength and hardness at different strain rates, the hardness-yield strength relationship was constructed. Keywords - Hardness; Nanoindentation; Reverse algorithm; Yield strength. I. INTRODUCTION II. METHODS Structural steel is one of the most widely used A. Determination of the Hardness materials in the bridge and building construction due The hardness of the material can be extracted from to several advantages, such as the low cost and easy the load-penetration depth curve of indentation, as machinability and weldability. The hardness (H) and follows [1]: the yield strength (y) are the important material properties of structural steels. In order to determine the hardness and yield strength, several tests must be where Pm is a maximum applied load, Ac is the carried out, such as the tensile, compressive, and projected contact area. In the indentation technique, indentation tests, in which the indentation test is a the project area is calculated by using the following good choice since this test allows extracting both the equation [2] hardness and yield strength of materials [1]-[3]. Furthermore, the indentation technique has several advantages, such as the short testing time and the low where hc is the contact depth. cost. In early works, the relationship between hardness and B. Determination of the Yield Strength The true stress - strain curve of structural steel can be yield strength has been constructed by combining the expressed as follows [3]: results from tensile and indentation tests [4], [5]. In these studies, the yield strength was obtained from the tensile test, while the hardness was obtained from indentation test. However, determining the H/y ratio by using these both tensile and indentation tests is a high cost and time-consuming task. The relationship between hardness and yield strength was also where y is a yield strain, st is the strain at the investigated based on the open literatures for the starting-point of strain hardening, is a plastic indentation technique [6]. Although that method is property defined as the ratio of st and y, E is acceptable, the inconsistent input data of the yield elastic modulus, and n is strain hardening exponent. strength and hardness values are a limitation of the The yield strength of structural steel can be study because the hardness-yield strength correlation determined from the indentation data by using a is constructed based on the data collected from seven reverse algorithm, which consists of following different studies [6]. The yield strength now can be dimensionless equations [3] calculated by using a reverse algorithm for indentation technique [3]. The aim of this study is to investigate the relationship between the hardness and the yield strength by using indentation technique. Investigating the Relationship Between Hardness and Yield Strength of Ss400 Steel Using Nanoindentation 31 International Journal of Advances in Mechanical and Civil Engineering, ISSN: 2394-2827 Volume-4, Issue-2, Aprl.-2017 http://iraj.in where aijk and bijk are coefficients, and C is the assembled from the hardness and the yield strength 2 values at the different strain rates. loading curvature calculated as C Pm/ h m . III. EXPERIMENTS In this study, the relationship between hardness and yield strength is found to be described by an exponent A. Specimen Preparation equation as follows: The specimen for the indentation test is a flat plate with a size of 20 mm x 12 mm x 8 mm. Fig. 1 shows the samples of SS400 steel after being mounted and where a and b are material dependent constants, polished. which are 71.12 and 0.00089, respectively. Fig. 1. Specimen of structural steel after polishing. B. Nano Hardness test Nanohardness tests are carried out at room temperature using Continuous Stiffness Measurement Fig. 3. The relationship between hardness and yield strength. (CSM) technique by controlling a loading strain rate. Berkovich indenter made of industrial diamond with It can be recognized that (6) well describes the an elastic modulus of 1140 GPa and Poison’s ratio of hardness-yield strength relationship with an R-square 0.07 is imployed. The maximum displacement is of 0.85. The correlation between hardness and yield 2000 nm, which is applied to all points during strength constructed based on the indentation results indentation tests. is reliable and acceptable. I. IV. RESULTS AND DISCUSSIONS CONCLUSIONS A. Load-Displacement curves In this study, the nanoindentation test is performed on Fig. 2 presents the load-displacement curves of structural steel with different strain rate. The structural steel. The results show that the maximum relationship between the hardness and the yield load increases when the strain rate increases. From strength was investigated based on assembling the the indentation data that are extracted from the load- values of hardness and yield strength at different displacement curves, several material properties can strain rates. The hardness-yield strength relationship be calculated, such as the hardness and the yield can be described by an exponent equation. strength. REFERENCES [1] Oliver WC, Pharr GM, “An improved technique for determining hardness and elastic-modulus using load and displacement sensing indentation experiments,” J Mater Res, vol. 7, pp. 1564–1583, June 1992. [2] Dao M, Chollacoop N, Van Vliet KJ, Venkatesh TA, Suresh S, “Computational modeling of the forward and reverse problems in instrumented sharp indentation,” Acta Mater, vol. 49, pp. 3899–3918, Aug. 2001. [3] Pham T-H, Kim J-J, Kim S-E, “Estimating constitutive equation of structural steel using indentation,” Int J Mech Sci, vol. 90, pp. 151-161, April 2014. [4] Cahoon JR, Broughton WH, Kutzak AR, “The determination of yield strength from hardness measurements,” Metall Trans, Fig. 2. The load-displacement curves of nanohardness test at vol. 2, pp. 1979–83, July 1971. different loading strain rates. [5] Currey JD, Brear K, “Hardness, Young’s modulus and yield stress in mammalian mineralized tissues,” J Mater Sci Mater, B. The Relationship between Yield Strength and vol. 1, pp. 14–20, June 1990. [6] Busby JT, Hash MC, Was GS, “The relationship between Hardness hardness and yield stress in irradiated austenitic and ferritic Fig. 3 shows the correlation between hardness and steels,” J Nucl Mater, vol. 336, pp. 267–278, Sep. 2004. yield strength. The input data of this correlation are Investigating the Relationship Between Hardness and Yield Strength of Ss400 Steel Using Nanoindentation 32 .
Load more

Recommended publications
  • 10-1 CHAPTER 10 DEFORMATION 10.1 Stress-Strain Diagrams And
    EN380 Naval Materials Science and Engineering Course Notes, U.S. Naval Academy CHAPTER 10 DEFORMATION 10.1 Stress-Strain Diagrams and Material Behavior 10.2 Material Characteristics 10.3 Elastic-Plastic Response of Metals 10.4 True stress and strain measures 10.5 Yielding of a Ductile Metal under a General Stress State - Mises Yield Condition. 10.6 Maximum shear stress condition 10.7 Creep Consider the bar in figure 1 subjected to a simple tension loading F. Figure 1: Bar in Tension Engineering Stress () is the quotient of load (F) and area (A). The units of stress are normally pounds per square inch (psi). = F A where: is the stress (psi) F is the force that is loading the object (lb) A is the cross sectional area of the object (in2) When stress is applied to a material, the material will deform. Elongation is defined as the difference between loaded and unloaded length ∆푙 = L - Lo where: ∆푙 is the elongation (ft) L is the loaded length of the cable (ft) Lo is the unloaded (original) length of the cable (ft) 10-1 EN380 Naval Materials Science and Engineering Course Notes, U.S. Naval Academy Strain is the concept used to compare the elongation of a material to its original, undeformed length. Strain () is the quotient of elongation (e) and original length (L0). Engineering Strain has no units but is often given the units of in/in or ft/ft. ∆푙 휀 = 퐿 where: is the strain in the cable (ft/ft) ∆푙 is the elongation (ft) Lo is the unloaded (original) length of the cable (ft) Example Find the strain in a 75 foot cable experiencing an elongation of one inch.
    [Show full text]
  • Transportation Vehicle Light-Weighting with Polymeric Glazing and Mouldings
    GCEP Final Report for Advanced Transportation Transportation Vehicle Light-Weighting with Polymeric Glazing and Mouldings Investigators Reinhold H. Dauskardt, Professor; Yichuan Ding, Graduate Researcher; Siming Dong, Graduate Researcher; Dongjing He, Summer student; Material Science and Engineering, Stanford University. Abstract Polymeric glazing and mouldings are an extremely high “want” from the transportation community, enabling more creative designs as well as improved part consolidation。 However, plastic windows and mouldings must have high-performance and low-cost protective coating systems with lifetimes in excess of 10 years. Current polymeric glazings do not meet durability/performance requirements for near-term implementation. Our project targets new coating system manufacturing to address durability and cost issues necessary to meet or exceed transportation engineering requirements. Atmospheric plasma deposition (APD) is an emerging technique that enables plasma deposition of coatings on large and/or complex geometry substrates in ambient air without the need for expensive vacuum or inert manufacturing platforms. It is an environmentally friendly and solvent-free technique, minimizing chemical waste throughout the process as well as greenhouse gas emissions when compared to current wet chemistry aqueous sol-gel manufacturing techniques. Low deposition temperatures (<50°C) allows the deposition on plastic and organic substrates. Using our state-of-the-art APD coating capabilities, we have demonstrated the ability to deposit highly transparent bilayer organosilicate coatings with superior combinations of elastic modulus and adhesion compared to commercial sol-gel coatings. The bilayer is deposited on large substrates by atmospheric plasma, in ambient air, at room temperature, in a one-step process, using a single inexpensive precursor. The significantly improved elastic modulus translates into improved durability and resistance to scratching and environmental degradation.
    [Show full text]
  • Correlation of Hardness Values to Tensile Strength
    Correlation of Hardness Values to Tensile Strength Semih Genculu, P.E. Various procedures and approaches are utilized to determine if a given material is suitable for a certain application. The material may be tested for its ability to deform satisfactorily during a forming operation, or perhaps for its ability to operate under a certain stress level at high temperatures. For technological purposes, economy and ease of testing are important factors. Hardness tests: In many cases it is possible to substitute for the relatively time consuming and costly tensile test with a more convenient test of the plastic deformation behavior of metals, a hardness test. Hardness is defined as resistance of a material to penetration of its surface, and the majority of commercial hardness testers force a small penetrator (indenter) into the metal by means of an applied load. A definite value is obtained as the hardness of the metal, and this number can be related to the tensile strength of the metal. In the Rockwell test, hardness is measured by the depth to which the penetrator moves under a fixed load. The elastic component of the deformation is subtracted from the total movement. In the Brinell and Vickers/Knoop scales, on the other hand, the hardness is measured by dividing the load by the area of an indentation formed by pressing the corresponding indenters into the metal. Therefore while the Rockwell number is read directly from a gage, which is part of the tester, the Brinell and Vickers/Knoop require optical measurements of the diameters or diagonals, respectively. While all indentation hardness tests may be thought to serve the same purpose, each one has definite advantages with some being more applicable to certain types of materials and size and shape parts than the others.
    [Show full text]
  • Guide to Copper Beryllium Wire Bar Tube Plate
    strip rod Guide to Copper Beryllium wire bar tube plate Brush Wellman is the leading worldwide supplier of High Performance Copper Alloys, including Copper Beryllium. We provide manufacturing excellence in the form of high reliability products and services to satisfy our customers’ most demanding applications. We provide these services in a culture of local support and global teamwork. © 2002 Brush Wellman Inc. Cleveland, Ohio Product Guide - Strip Content Alloy Guide . 3 Wrought Alloys. 4 Wrought Products . 5 Physical Properties . 6 Product Guide . 7 Strip . 8 Temper Designations . 9 Mechanical and Electrical Properties. 10 Forming . 12 Stress Relaxation . 13 Wire. 14 Rod, Bar and Tube . 16 Plate and Rolled Bar. 18 Forgings and Extrusions . 20 Drill String Products . 21 Other Products and Services . 22 Engineering Guide. 23 Heat Treatment Fundamentals. 24 Phase Diagrams . 24 Cold Work Response . 25 Age Hardening . 26 Microstructures . 29 Cleaning and Finishing. 30 Joining-Soldering, Brazing and Welding. 31 Machining. 32 Hardness . 33 Fatigue Strength . 35 Corrosion Resistance . 36 Other Attributes . 37 Your Supplier . 39 This is Brush Wellman . 40 Company History. 40 Corporate Profile. 40 Mining and Manufacturing.. 41 Product Distribution . 42 Customer Service . 43 Quality . 43 Safe Handling . 44 2 Alloy Guide Wrought Alloys 4 Wrought Products 5 Physical Properties 6 The copper beryllium alloys commonly supplied in wrought product form are highlighted in this section. Wrought products are those in which final shape is achieved by working rather than by casting. Cast alloys are described in separate Brush Wellman publications. Although the alloys in this guide are foremost in the line that has established Brush Wellman’s worldwide reputation for quality, they are not the only possibilities.
    [Show full text]
  • 1 Introduction to Hardness Testing
    Copyright © 1999 ASM International ® Hardness Testing, 2nd Edition, 06671G All rights reserved. Harry Chandler, editor www.asminternational.org 1 Introduction to Hardness Testing Hardness has a variety of meanings. To the metals industry, it may be thought of as resistance to permanent deformation. To the metallurgist, it means resistance to penetration. To the lubrication engineer, it means resis- tance to wear. To the design engineer, it is a measure of flow stress. To the mineralogist, it means resistance to scratching, and to the machinist, it means resistance to machining. Hardness may also be referred to as mean contact pressure. All of these characteristics are related to the plastic flow stress of materials. Measuring Hardness Hardness is indicated in a variety of ways, as indicated by the names of the tests that follow: • Static indentation tests: A ball, cone, or pyramid is forced into the sur- face of the metal being tested. The relationship of load to the area or depth of indentation is the measure of hardness, such as in Brinell, Knoop, Rockwell, and Vickers hardness tests. • Rebound tests: An object of standard mass and dimensions is bounced from the surface of the workpiece being tested, and the height of rebound is the measure of hardness. The Scleroscope and Leeb tests are exam- ples. • Scratch file tests: The idea is that one material is capable of scratching another. The Mohs and file hardness tests are examples of this type. • Plowing tests: A blunt element (usually diamond) is moved across the surface of the workpiece being tested under controlled conditions of load Copyright © 1999 ASM International ® Hardness Testing, 2nd Edition, 06671G All rights reserved.
    [Show full text]
  • Hardness - Yield Strength Relation of Al-Mg-Si Alloys with Enhanced Strength and Conductivity V.D
    IOP Conference Series: Materials Science and Engineering PAPER • OPEN ACCESS Related content - Precipitates studies in ultrafine-grained Al Hardness - Yield Strength Relation of Al-Mg-Si alloys with enhanced strength and conductivity V.D. Sitdikov, M.Yu. Murashkin and R.Z. Alloys Valiev - The Contrast of Electron Microscope To cite this article: Aluru Praveen Sekhar et al 2018 IOP Conf. Ser.: Mater. Sci. Eng. 338 012011 Images of Thick Crystalline Object. Experiment with an Al-Mg-Si Alloy at 50- 100 kV. Toshio Sahashi - Microstructure features and mechanical View the article online for updates and enhancements. properties of a UFG Al-Mg-Si alloy produced via SPD E Bobruk, I Sabirov, V Kazykhanov et al. This content was downloaded from IP address 170.106.33.14 on 24/09/2021 at 15:30 NCPCM 2017 IOP Publishing IOP Conf. Series: Materials Science and Engineering1234567890 338 (2018)‘’“” 012011 doi:10.1088/1757-899X/338/1/012011 Hardness - Yield Strength Relation of Al-Mg-Si Alloys Aluru Praveen Sekhar*, Supriya Nandy, Kalyan Kumar Ray and Debdulal Das Department of Metallurgy and Materials Engineering, Indian Institute of Engineering Science and Technology, Shibpur, Howrah - 711103, West Bengal, India *Corresponding author E-mail address: [email protected] Abstract: Assessing the mechanical properties of materials through indentation hardness test is an attractive method, rather than obtaining the properties through destructive approach like tensile testing. The present work emphasizes on the relation between hardness and yield strength of Al-Mg-Si alloys considering Tabor type equations. Al-0.5Mg-0.4Si alloy has been artificially aged at various temperatures (100 to 250 oC) for different time durations (0.083 to 1000 h) and the ageing response has been assessed by measuring the Vickers hardness and yield strength.
    [Show full text]
  • Calculation of the Hardness of a Multi-Element Equiatomic Metal Alloy
    Modern Approaches on Material Science DOI: 10.32474/MAMS.2020.02.000136 ISSN: 2641-6921 Mini Review Calculation of the Hardness of a Multi-Element Equiatomic Metal Alloy Zakarian DA* and Khachatrian AV Frantzevich Institute for Problems of Materials Science NAS Ukraine, Kiev *Corresponding author: Zakarian DA, Frantzevich Institute for Problems of Materials Science NAS Ukraine, Kiev Received: December 20, 2019 Published: January 16, 2020 Abstract A phenomenological approach has been developed for the mathematical description of the hardening of high-entropy alloys (HEAs) and a quantitative assessment of their hardness. It is shown that in HEAs with a bcc lattice, the degree of hardening is always greater than in HEAs with a fcc lattice (with the same number of elements in alloys). To calculate the relative hardening of the alloy, hardnessthe type of and crystal degree lattice of hardening and its parameter of multi-element value are alloys required. (HEAS). The calculation results are consistent with experimental data. Basic parameters of HEAs are calculated from first principles. The proposed method can be considered acceptable for assessing the Keywords: Multielement alloys; energy of interaction of elements; mismatch parameter; distortion density; hardness; heas Introduction difference in the radii of the atoms present in the alloy. Basically, One of the most common characteristics that determine the the mean quadratic displacement of atoms from the equilibrium quality of metals and alloys, the possibility of their use in various position in an ideal, undistorted lattice is used as a mismatch designs and under various working conditions, is hardness. parameter [1,2]. Hardness tests are performed more often than determining other mechanical characteristics of metals: strength, elongation, etc.
    [Show full text]
  • 5. Mechanical Properties and Performance of Materials
    5. MECHANICAL PROPERTIES AND PERFORMANCE OF MATERIALS Samples of engineering materials are subjected to a wide variety of mechanical tests to measure their strength, elastic constants, and other material properties as well as their performance under a variety of actual use conditions and environments. The results of such tests are used for two primary purposes: 1) engineering design (for example, failure theories based on strength, or deflections based on elastic constants and component geometry) and 2) quality control either by the materials producer to verify the process or by the end user to confirm the material specifications. Because of the need to compare measured properties and performance on a common basis, users and producers of materials use standardized test methods such as those developed by the American Society for Testing and Materials (ASTM) and the International Organization for Standardization (ISO). ASTM and ISO are but two of many standards-writing professional organization in the world. These standards prescribe the method by which the test specimen will be prepared and tested, as well as how the test results will be analyzed and reported. Standards also exist which define terminology and nomenclature as well as classification and specification schemes. The following sections contain information about mechanical tests in general as well as tension, hardness, torsion, and impact tests in particular. Mechanical Testing Mechanical tests (as opposed to physical, electrical, or other types of tests) often involves the deformation or breakage of samples of material (called test specimens or test pieces). Some common forms of test specimens and loading situations are shown in Fig 5.1.
    [Show full text]
  • Rock and Mineral Identification for Engineers
    Rock and Mineral Identification for Engineers November 1991 r~ u.s. Department of Transportation Federal Highway Administration acid bottle 8 granite ~~_k_nife _) v / muscovite 8 magnify~in_g . lens~ 0 09<2) Some common rocks, minerals, and identification aids (see text). Rock And Mineral Identification for Engineers TABLE OF CONTENTS Introduction ................................................................................ 1 Minerals ...................................................................................... 2 Rocks ........................................................................................... 6 Mineral Identification Procedure ............................................ 8 Rock Identification Procedure ............................................... 22 Engineering Properties of Rock Types ................................. 42 Summary ................................................................................... 49 Appendix: References ............................................................. 50 FIGURES 1. Moh's Hardness Scale ......................................................... 10 2. The Mineral Chert ............................................................... 16 3. The Mineral Quartz ............................................................. 16 4. The Mineral Plagioclase ...................................................... 17 5. The Minerals Orthoclase ..................................................... 17 6. The Mineral Hornblende ...................................................
    [Show full text]
  • Enghandbook.Pdf
    785.392.3017 FAX 785.392.2845 Box 232, Exit 49 G.L. Huyett Expy Minneapolis, KS 67467 ENGINEERING HANDBOOK TECHNICAL INFORMATION STEELMAKING Basic descriptions of making carbon, alloy, stainless, and tool steel p. 4. METALS & ALLOYS Carbon grades, types, and numbering systems; glossary p. 13. Identification factors and composition standards p. 27. CHEMICAL CONTENT This document and the information contained herein is not Quenching, hardening, and other thermal modifications p. 30. HEAT TREATMENT a design standard, design guide or otherwise, but is here TESTING THE HARDNESS OF METALS Types and comparisons; glossary p. 34. solely for the convenience of our customers. For more Comparisons of ductility, stresses; glossary p.41. design assistance MECHANICAL PROPERTIES OF METAL contact our plant or consult the Machinery G.L. Huyett’s distinct capabilities; glossary p. 53. Handbook, published MANUFACTURING PROCESSES by Industrial Press Inc., New York. COATING, PLATING & THE COLORING OF METALS Finishes p. 81. CONVERSION CHARTS Imperial and metric p. 84. 1 TABLE OF CONTENTS Introduction 3 Steelmaking 4 Metals and Alloys 13 Designations for Chemical Content 27 Designations for Heat Treatment 30 Testing the Hardness of Metals 34 Mechanical Properties of Metal 41 Manufacturing Processes 53 Manufacturing Glossary 57 Conversion Coating, Plating, and the Coloring of Metals 81 Conversion Charts 84 Links and Related Sites 89 Index 90 Box 232 • Exit 49 G.L. Huyett Expressway • Minneapolis, Kansas 67467 785-392-3017 • Fax 785-392-2845 • [email protected] • www.huyett.com INTRODUCTION & ACKNOWLEDGMENTS This document was created based on research and experience of Huyett staff. Invaluable technical information, including statistical data contained in the tables, is from the 26th Edition Machinery Handbook, copyrighted and published in 2000 by Industrial Press, Inc.
    [Show full text]
  • Heat Treating Copper Beryllium Parts
    Tech Brief Heat Treating Copper Beryllium Parts Heat treating is key to the ver- satility of the copper beryllium alloy system Unlike other copper base alloys which acquire their strength through cold work alone, wrought copper beryllium obtains its high strength, conductivity, and hardness through a combina- tion of cold work and a thermal process called age hardening. 800.375.4205 | materion.com/copperberyllium Age hardening is often referred to as precipitation hardening strength with moderate to good conductivity; and High or heat treating. The ability of these alloys to accept this Conductivity Copper Beryllium features maximum conduc- heat treatment results in forming and mechanical property tivity and slightly lower strength levels. advantages not available in other alloys. For example, Both the High Strength and High Conductivity Copper intricate shapes can be fabricated when the material is in Beryllium are available as strip in the heat treatable and its ductile, as rolled state and subsequently age hardened to mill hardened tempers. Mill hardened tempers are supplied the highest strength and hardness levels of any copper base in the heat treated condition and require no further heat alloy. treatment. Heat treating the copper beryllium alloys is a two step pro- Copper beryllium is produced in tempers ranging from cess which consists of solution annealing and age hardening. solution annealed (A) to an as rolled condition (H). Heat Because Materion Brush Performance Alloys performs the treating maximizes the strength and conductivity of these required solution anneal on all wrought products prior alloys. The temper designations of the standard age harden- to shipping, most fabricators’ primary concern is the age able copper beryllium tempers are shown in Table 2.
    [Show full text]
  • The Hardness of Additively Manufactured Alloys
    Preprints (www.preprints.org) | NOT PEER-REVIEWED | Posted: 5 October 2018 doi:10.20944/preprints201810.0096.v1 Peer-reviewed version available at Materials 2018, 11, 2070; doi:10.3390/ma11112070 The hardness of additively manufactured alloys J.S. Zuback and T. DebRoy* Department of Materials Science and Engineering, The Pennsylvania State University, University Park, PA 16802 *Corresponding author: [email protected] (T.D.) Table of Contents Abstract ........................................................................................................................................... 2 1. Introduction ................................................................................................................................. 3 2. Influence of process variables ..................................................................................................... 5 2.1 Energy input .......................................................................................................................... 5 2.2 Cooling rates ......................................................................................................................... 6 3. Effects of microstructure............................................................................................................. 9 3.1 Iron based alloys ................................................................................................................... 9 3.2 Aluminum alloys .................................................................................................................
    [Show full text]