Exposed Rafter Eaves Detail

Total Page：16

File Type：pdf, Size：1020Kb

CONCRETE INTERLOCKING ROOF TILES ON 50x25 SW BATTENS. RECOMMENDED GAUGE ON TYVEK SUPRO BREATHER MEMBRANE. ALL TRUSSED RAFTERS AT MAX 600cts. CONCRETE INTERLOCKING ROOF TILES INSULATION QUILT BETWEEN ON 50x25 SW BATTENS. RECOMMENDED TRUSSES THROUGHOUT ROOF GAUGE ON TYVEK SUPRO BREATHER SPACE & TAKEN INTO REAR OF MEMBRANE. ALL TRUSSED RAFTERS AT JABLITE INSULINK - REFER TO MAX 600cts. HOUSE TYPE WORKING DRAWING FOR DEPTH INSULATION QUILT BETWEEN TRUSSES THROUGHOUT ROOF NOGGIN POSITIONED 10mm OVER SPACE & TAKEN INTO REAR OF WALLPLATE. JABLITE INSULINK - REFER TO HOUSE TYPE WORKING DRAWING FOR DEPTH 150 x 6 CONTINUOUS NOGGIN POSITIONED 10mm OVER PLY TILTING FILLET ON WALLPLATE. 400 WIDE X 6MM PLY 100mm DIA. HR PVC. 150 x 6 CONTINUOUS EAVES GUTTER. PLY TILTING FILLET ON 400 WIDE X 6MM PLY 38x38mm TREATED NOGGIN POSITIONED BETWEEN RAFTERS, TO 100mm DIA. HR PVC. TIMBER GUTTER EAVES GUTTER. COINCIDE WITH LOWER EDGE OF THE BOARD (100 X 25) RAFTERS TO SUPPORT PLASTERBOARD EBONY STAIN FINISH CEILING EDGES, NOGGIN TO BE NAIL FIXED TO SIDES OF RAFTERS. PLASTER 150 EXPOSED RAFTER JUNCTIONS TO HAVE CONTINUOUS ENDS 38x38mm TREATED NOGGIN TIMBER GUTTER RIBBON OF PLASTER TO OVERCOME POSITIONED BETWEEN RAFTERS, TO BOARD (100 X 25) AIR LEAKAGE. 100 x 50 mm SW COINCIDE WITH LOWER EDGE OF THE EBONY STAIN FINISH WALLPLATE ON RAFTERS TO SUPPORT PLASTERBOARD MORTAR BED CEILING EDGES, NOGGIN TO BE NAIL 150 EXPOSED RAFTER INSULATED LINTEL STRAPPED AT MAX 300 FIXED TO SIDES OF RAFTERS. PLASTER ENDS 2000mm CTS WITH 30 x JUNCTIONS TO HAVE CONTINUOUS 40 DEG. PITCH 5 GALV. MS STRAPS. 100 x 50 mm SW RIBBON OF PLASTER TO OVERCOME WALLPLATE ON AIR LEAKAGE. MORTAR BED CONCRETE INTERLOCKING ROOF TILES STRAPPED AT MAX ON 50x25 SW BATTENS. RECOMMENDED 2000mm CTS WITH 30 x GAUGE ON TYVEK SUPRO BREATHER 5 GALV. MS STRAPS. MEMBRANE. ALL TRUSSED RAFTERS AT INSULATED LINTEL MAX 600cts. INSULATION QUILT BETWEEN 50 DEG. PITCH TRUSSES THROUGHOUT ROOF 300 SPACE & TAKEN INTO REAR OF JABLITE INSULINK - REFER TO HOUSE TYPE WORKING DRAWING FOR DEPTH NOGGIN POSITIONED 10mm OVER WALLPLATE. 150 x 6 CONTINUOUS PLY TILTING FILLET ON 400 WIDE X 6MM PLY 100mm DIA. HR PVC. EAVES GUTTER. 38x38mm TREATED NOGGIN TIMBER GUTTER POSITIONED BETWEEN RAFTERS, TO BOARD (100 X 25) COINCIDE WITH LOWER EDGE OF THE EBONY STAIN FINISH RAFTERS TO SUPPORT PLASTERBOARD CEILING EDGES, NOGGIN TO BE NAIL 150 EXPOSED RAFTER FIXED TO SIDES OF RAFTERS. PLASTER ENDS JUNCTIONS TO HAVE CONTINUOUS 100 x 50 mm SW REFER TO WORKING DRAWING MILTON AVENUE, CLITHEROE RIBBON OF PLASTER TO OVERCOME WALLPLATE ON AIR LEAKAGE. MORTAR BED FOR TRUSS VARIATIONS STRAPPED AT MAX INSULATED LINTEL 2000mm CTS WITH 30 x PLEASE REFER TO ACCREDITED DETAILS FOR 5 GALV. MS STRAPS. RAFTER EAVES DETAILS 35 DEG. PITCH 300 REDUCING AIR PERMEABILITY 02/12/16 RDL 1:20 N286/DET/001.

Copy Link

Recommended publications

A Concise Dictionary of Middle English
A Concise Dictionary of Middle English A. L. Mayhew and Walter W. Skeat A Concise Dictionary of Middle English Table of Contents A Concise Dictionary of Middle English...........................................................................................................1 A. L. Mayhew and Walter W. Skeat........................................................................................................1 PREFACE................................................................................................................................................3 NOTE ON THE PHONOLOGY OF MIDDLE−ENGLISH...................................................................5 ABBREVIATIONS (LANGUAGES),..................................................................................................11 A CONCISE DICTIONARY OF MIDDLE−ENGLISH....................................................................................12 A.............................................................................................................................................................12 B.............................................................................................................................................................48 C.............................................................................................................................................................82 D...........................................................................................................................................................122
[Show full text]
Chapter 2: TRUSS and ROOF TERMINOLOGY
Chapter 2: TRUSS AND ROOF TERMINOLOGY APEX: The highest point on a truss where the sloping top chords meet (Figures 3, 4 & 6). AXIAL FORCE: A push (compression) or pull (tension) acting along the length of a member. Usually measured in Newtons (N) or kiloNewtons (kN). (Figure 18) AXIAL STRESS: The axial force acting at a point along the length of a member, divided by the cross- sectional area of the member. Usually measured in MegaPascals (MPa) or Newtons per square millimeter (N/mm2). (Figure 18) BARGE BOARDS: Trim boards applied to gable ends of buildings. (Figure 2 & 10) BATTENS: Small-section timber members – usually 36x36 (See SANS 1783-4) spanning between trusses, connected to the top of the top chord of the truss and usually supporting a roof covering of tiles or slates (Figure 4). BATTEN CENTRES: The distance between centre lines of battens, measured along the slope of the top chord (Figure 8). BAY LENGTH: Also called PANEL LENGTH. In a truss this refers to the horizontal distance between the centres of joints or nodes in either the top or bottom chord. In a roof, it refers to the space between trusses, e.g. a single or double truss spacing where bracing occurs. (Figure 7 & 8) BRACED BAY: The space between 2 or more trusses in a roof section where bracing is positioned (Figure 2) BEAM: A solid or composite timber lintel that usually supports trusses or rafters. (Figure 11) BEAM POCKET: A void deliberately set into a wall to allow a beam, truss horn or floor truss to bear on the wall.
[Show full text]
BRACING USING NZS 3604:2011 – PART 1 Providing Sufficient Bracing Capacity for Wind and Earthquake Is an Integral Part of the Design Process
DESIGN RIGHT BRACING USING NZS 3604:2011 – PART 1 Providing sufficient bracing capacity for wind and earthquake is an integral part of the design process. This series starts by looking at the information needed for bracing calculations. By Tom Edhouse, BRANZ Technical Advisor racing for a timber-framed building h = height of is required to resist horizontal wind roof above eaves and earthquake forces. The bracing H for subfloor (Table 5.5) demand to resist wind is expressed H for top or single storey (Table 5.6) Bin bracing units (B/Us) per lineal metre and 10 m max. for bracing units per square metre for earthquakes. NZS 3604 scope upper floor level Before starting bracing calculations, the H for lower of 2 storeys (Table 5.7) designer will need to collect the following lower floor level information for the specific building. average ground height NZS 3604:2011 Is the building being considered within the scope of NZS 3604:2011? For this, it must be lowest ground point no more than 2-storeys and a maximum height of 10 m from the lowest ground level to the Figure 1: How to work out H and h. uppermost portion of the roof. W where roof pitch is Designs within the scope of NZS 3604:2011 wind direction along ridge greater than 25° must provide bracing capacity that exceeds the higher of the minimum requirements in NZS 3604:2011 for: ❚ wind demand – Tables 5.5, 5.6 and 5.7 ❚ earthquake demand – Tables 5.8, 5.9 and 5.10. W where roof pitch is Wind zone less than 25° Some territorial authorities have maps with wind bracing elements in line with zones.
[Show full text]
Dutch Gable Freestanding Carport
DUTCH GABLE FREESTANDING CARPORT STRATCO OUTBACK® ASSEMBLY INSTRUCTIONS. Your complete guide to building a FREESTANDING Outback DUTCH GABLE CARPORT BEFORE YOU START Carefully read these instructions. If you do not have all the necessary tools or information, contact Stratco for advice. Before starting lay out all components and check them against the delivery docket. The parts description identifies each key part, and the component location diagram indicates their fastening position. PARTS DESCRIPTION RIDGE KNUCKLE FOOTING PLATE EAVES KNUCKLE FOOTING COLUMNS AND Slots inside the gable rafters to Slots inside column Slots inside gable rafter and KNUCKLE RAFTERS form connection at the ridge to form on concrete column to form connection at Slots inside Pre cut 120 outback footing connection. eaves. column to form beam make up an in ground rafters and columns footing connection PURLINS HIP PLATE RIDGE CAP BARGE CAP INFILL PANELS Purlins provide support for Connects purlins to This flashing covers the roof The barge cap covers Sufficient number of sheets are cladding the hip rafter. sheets at the gable ridge. the area where the provided, from which the required deck finishes at portal dutch gable infill panels can be HIP FLASHING frame cut. Covers the roof sheet ends along the hip rafter. WEATHER STRIP HEX HEAD SELF DRILLING BOLTS AND RIVETS 68 mm PURLIN Weather strip supports infill SCREWS Bolt types vary depending BRACKET panel and covers the sheet Screw types vary depending upon upon the connection, ensure This bracket ends at the collar
[Show full text]
Roof Truss – Fact Book
Truss facts book An introduction to the history design and mechanics of prefabricated timber roof trusses. Table of contents Table of contents What is a truss?. .4 The evolution of trusses. 5 History.... .5 Today…. 6 The universal truss plate. 7 Engineered design. .7 Proven. 7 How it works. 7 Features. .7 Truss terms . 8 Truss numbering system. 10 Truss shapes. 11 Truss systems . .14 Gable end . 14 Hip. 15 Dutch hip. .16 Girder and saddle . 17 Special truss systems. 18 Cantilever. .19 Truss design. .20 Introduction. 20 Truss analysis . 20 Truss loading combination and load duration. .20 Load duration . 20 Design of truss members. .20 Webs. 20 Chords. .21 Modification factors used in design. 21 Standard and complex design. .21 Basic truss mechanics. 22 Introduction. 22 Tension. .22 Bending. 22 Truss action. .23 Deflection. .23 Design loads . 24 Live loads (from AS1170 Part 1) . 24 Top chord live loads. .24 Wind load. .25 Terrain categories . 26 Seismic loads . 26 Truss handling and erection. 27 Truss fact book | 3 What is a truss? What is a truss? A “truss” is formed when structural members are joined together in triangular configurations. The truss is one of the basic types of structural frames formed from structural members. A truss consists of a group of ties and struts designed and connected to form a structure that acts as a large span beam. The members usually form one or more triangles in a single plane and are arranged so the external loads are applied at the joints and therefore theoretically cause only axial tension or axial compression in the members.
[Show full text]
Bracing Supplement
Supplement Bracing WWW.BRANZ.CO.NZ YOU’RE PROTECTED WITH GIB EZYBRACE® SYSTEMS. For over 30 years, Kiwi building professionals like you have been relying on GIB® bracing systems. Designed and tested in New Zealand for local conditions, they meet and exceed New Zealand’s stringent building codes and are backed by local technical support. So you can build with confidence and complete peace of mind.* GIB EzyBrace® Systems software and technical literature is available at gib.co.nz/ezybrace. Or for technical support call the GIB® Helpline on 0800 100 442. J1/WWB0020/BLD DOWNLOAD THE GIB® APP NOW Go to your App Store or Google Play Store. 2 — Build — Bracing GIB® is a registered trademark. *Provided they are used, stored, installed and maintained strictly in accordance with current Winstone Wallboards technical information. WWB0020 LBTS Trust BLD ad.indd 1 21/02/14 9:40 AM YOU’RE PROTECTED WITH GIB EZYBRACE® SYSTEMS. For over 30 years, Kiwi building professionals like you have been relying on GIB® bracing systems. Designed and tested in New Zealand for local conditions, they meet and exceed New Zealand’s stringent building codes and are backed by local technical support. So you can build with confidence and complete peace of mind.* GIB EzyBrace® Systems software and technical literature Supplement is available at gib.co.nz/ezybrace. Or for technical support call the GIB® Helpline on 0800 100 442. Bracing 3 19 1. Introduction 7. Bracing for steps in ﬂoors and ceilings 4 21 2. Bracing using NZS 3604:2011 8. Wall bracing 8 26 3.
[Show full text]
Kotes-Kenny House
VILLAGE OF DOWNERS GROVE ARCHITECTURAL DESIGN REVIEW BOARD JANUARY 13, 2021 AGENDA SUBJECT: TYPE: SUBMITTED BY: 20-ADR-0001 Gabriella Baldassari 200 Shady Lane Designation of a Historic Landmark Development Planner REQUEST The petitioners are seeking a Historic Landmark Designation for their home at 200 Shady Lane based on the criteria that the property represents the distinguishing characteristics of an architectural style. NOTICE The application has been filed in conformance with applicable procedural and public notice requirements. GENERAL INFORMATION OWNER/PETITIONER: Christie and John Kenny 200 Shady Lane Downers Grove, IL 60515 PROPERTY INFORMATION ARCHITECTURAL STYLE: Mid-Century Modern BUILDING DATE: Circa 1960 HISTORICAL BUILDING USE: Single Family Residence EXISTING BUILDING USE: Single Family Residence PROPERTY SIZE: 11,104 Square Feet (.25 acres) PIN: 09-04-108-018 ANALYSIS SUBMITTALS This report is based on the following documents, which are on file with the Department of Community Development: 1. Project Summary 2. Plat of Survey 3. Owner Consent Form 4. Certificate of Acknowledgement Form 5. Historic Landmark Information Form 6. Photographs 7. Village of Downers Grove Architectural and Historical Survey 2013 PROJECT DESCRIPTION The petitioners are seeking a Historic Landmark Designation for their property at 200 Shady Lane under criteria 12.302.B.3 of the Historic Preservation Ordinance: representation of distinguishing characteristics of an architectural style. The Mid-Century Modern style home was constructed circa 1960. 20-ADR-0001, 200 Shady Lane Page 2 January 13, 2021 The Mid-Century Modern style was popularized between the 1940s and 1960s. The use of brick, stucco and wood siding (installed both vertically and horizontally) varied depending on geography.
[Show full text]
Easy Loft Installation Guide
A• Dolwnotaatytemspt two woorkrokn thse ajoisftse themselves, this can be dangerous and you could cause substantial damage to the ceiling of the room below should your footing slip. You should use a plank INSTALLATION of wood to slide over the joists that you can lean/stand on to support your weight. • If you do not have a good light source in the loft space, you should arrange for a lighting solution to INSTRUCTIONS be introduced. This could be either a temporary solution in the form of using an extension lead to run a cable through the loft to hang a light from one of the beams or you could even choose to fix a light permanently. Do not rely solely on using torchlight – use a torch in conjunction with another fixed light source. 1. OSntceepin l1 oft, remove product 2. Statretinpg f2 rom the eaves, ensure 3. WShtenpthe3 insulation has 4. ISnstuelapte a4 nd draft proof the loft from packaging and shake to the wall plate is covered and reached the tops of the joists, hatch sit back and enjoy the work towards the centre of the speed its recovery to nominal extra heat saving is achieved savings of a more energy thickness loft by unrolling the product – . by “cross layering” (at right efficient home see note below regarding . adequate ventilation. angles to the joists). The Lay EasyLoft between the Government advises that loft joists to achieve a depth of insulation should be a 100mm – EasyLoft can be minimum depth of 270mm used in conjunction with (including joist insulation). existing insulation.
[Show full text]
Roofline Windowline Cladding Roofline
Roofline Windowline Cladding Edition 7 PVC-UE...the roofline, specifier's windowline choice of Roofline and cladding products Windowline Cladding Specification Guide Contents Contents Celuform 3 Benefits of Celuform PVC-UE & PVC-U 4 Roofline Range and Colours 5 Fascia Installation Details 7 Fascia Installation Details 8 Bargeboard Installation Details 9 Soffit Installation Details 10 Roofline Range & Dimensions 11 Roofline Range & Dimensions 12 Boxed End Installation Details Roofline 13 Roofline Ventilation 14 Roofline Ventilation & Eaves Protection 15 Soffit Range 16-17 Typical Jointing Details 18 Working with Woodgrain Products: Roofline 19 Rafter Foot Covers 20 Fixing Summary - Roofline 21 White Cladding Installations 22 White Cladding Installations 24 White Cladding Installations 26 Cladding Range Celuform 27 Fixing Summary - Cladding Clading the UK’s first 28 Celuex Textured Cladding Installations 30 Celutex Cladding Range manufacturer of 31 Fixing Summary - Celutex Cladding PVC-UE building 32 Windowboard & Internal Trims products 34 Windowboard Range & Trims 35 Trim Range Window boards Window boards 36 Frequently Asked Questions 37 Product Characteristics 38 Product Characteristics Technical 39 Fixing Summary - General Head Office, Scunthorpe 2 ROOFLINE, CLADDING, WINDOWBOARDS & TRIMS Celuform Benefits of PVC-UE & PVC-U Celuform’s popularity in the new build, specification, Product Guarantees architectural and refurbishment sector stems from its Celuform’s white products are guaranteed for 20 years and product reliability and wide acceptance amongst the woodgrains for 10 years provided that approved installation trade and the general public. Refurbishment and maintenance instructions are followed. Copies of the programmes by housing associations and local guarantees are available from marketing on 0870 240 6107 GUARANTEE authorities acknowledge Celuform products as the Twenty Year Ten Year Colour route to lower maintenance costs.
[Show full text]
Junior High-High School Edition)
1 Glossary for the Virtual Tour (Junior High-High School Edition) A Acanthus – Representation of Acanthus plant leaf used in architecture and decorative arts as an ornamental motif, specifically in Classical architecture of the Greeks and Romans. Also used in the capital of the Corinthian order. Ad valorem taxes – Ad valorem is a Latin phrase meaning “according to the value,” meaning it is a tax proportional to the value of the underlying asset. Usually a type of property tax. Alabaster – A type of fine-grained gypsum that has been used for statuary, carvings, ornaments, church fittings, and monuments. Normally snow-white in color, however, it can be dyed or even be translucent depending on the treatment. Ante-chamber – A room that serves as a waiting area and entry to a larger chamber. Anthemion – A decoration in architecture consisting of radiating petals and used widely in Classical architecture. Arch – A curved structure, usually a doorway or gateway, that serves as support for a structure. Architect – A skilled person in the art of building, who designs complex structures such as government buildings, monuments, housing, etc. Architecture – The art and technique of designing and building. Architrave – In Classical architecture, the lowest section of the entablature (see entablature) directly above the capital of a column. Art Nouveau – Meaning “new art,” Art Nouveau is a style of art and architecture that was popular in the late 19th and early 20th centuries. It is known by its floral designs, flowing lines, and curved tendrils. Attic – Denotes any portion of a wall above the main cornice (see cornice).
[Show full text]
ADDING EAVES a Common Feature of Many Leaky Buildings Is That They Were Constructed Without Eaves, Usually with Walls Terminating with a Parapet
DESIGN RIGHT ADDING EAVES A common feature of many leaky buildings is that they were constructed without eaves, usually with walls terminating with a parapet. Changing this design detail can greatly enhance a building’s weathertightness. By Trevor Pringle, ANZIA, BRANZ Principal Writer aves can, depending on their width and Typically, pitched roofs can have outriggers Questions to ask the height above the ground, provide flitched to the side of the rafters or truss top Engineering advice may be needed on the significant shelter to a wall cladding chords to create eaves. Doing this involves total extension of rafters, particularly where and penetrations, such as windows, by removal of the parapet wall and its cladding and proposed eaves are wider than 400 mm. Edeflecting water away. the repair of any damaged wall framing. new profiled metal roofing matching existing, lapped under existing roofing 150 mm and sealed to prevent condensation running between sheets (see Metal Roofing Manufacturers Code of Practice 7.1.1) new roofing underlay lapped 150 mm min. under existing purlins to support roof extension roofing underlay and dressed into gutter, lift roofing as required to install new underlay minimum back span = 2 × eaves overhang new rafter extensions fixed to side of existing trusses/rafters minimum 10° pitch for corrugate profile turn-down to trapezoidal two M12 hot-dip galvanised and trough profile roofing if bolts with 50 × 50 × 5 mm roof pitch less than 10° washers each side blocking between existing roof trusses/rafters rafter extensions to support soffit new framing, wall underlay, insulation new edge purlin and lining as required new gutter and new soffit lining fascia, block beneath rafter behind as extensions required and paint fascia before installing new cladding on drained and vented gutter cavity on new wall underlay Note: 1 Roofing warranty not usually provided.
[Show full text]
Design Guide for Timber Roof Trusses
TFEC 4-2020 Design Guide for Timber Roof Trusses August 2020 This document is intended to be used by engineers to provide guidance in designing and evaluating timber roof truss structures. Do not attempt to design a timber roof truss structure without adult supervision from a qualified professional (preferably an experienced timber engineer). The Timber Frame Engineering Council (TFEC) and the Timber Framers Guild (TFG) assume no liability for the use or misuse of this document. TFEC-4 Committee: Jim DeStefano, P.E., AIA, F.SEI chairman Ben Brungraber, Ph.D., P.E. David Connolly, P.E. Jeff Hershberger, E.I. Jaret Lynch, P.E. Leonard Morse-Fortier, Ph.D., P.E. Robin Zirnhelt, P.Eng Illustrations by Ken Flemming and Josh Coleman Copyright © 2020 Timber Frame Engineering Council TFEC 4-2020 Page 2 Table of Contents Background 5 Truss Analysis 7 Ideal Trusses 7 Classical Methods 8 Graphical Methods 10 Squire Whipple 11 Computer Modeling 12 Truss Deflection and Camber 16 Development of Truss Forms 17 King Post Trusses 21 Queen Post Trusses 23 Howe Trusses 25 Pratt Trusses 26 Fink Trusses 27 Scissor Trusses 28 Hammer-Beam Trusses 31 Parallel Chord Trusses 34 Truss Joinery and Connections 36 Howe Truss Example 37 Scissor Truss Example 40 Scissor Truss with Clasping King 42 Block Shear 43 Friction and Joinery 45 Free Body Diagram 49 Steel Side Plates 50 Hardwood Pegs 53 Nuts and Bolts 55 Ogee Washers 57 TFEC 4-2020 Page 3 Split Rings and Shear Plates 58 Tension Joinery 59 Special Considerations 60 Truss Bracing 60 Raised and Dropped Bottom Chords 61 Curved Members 63 Grain Matched Glulams 68 Seasoning Shrinkage Considerations 69 Epilogue – Topped Out 71 TFEC 4-2020 Page 4 Background Man has been building with timber trusses for over 2,000 years.
[Show full text]