N-06C INSTRUCTION MANUAL ’11.6 Introduction Please keep a separate record of the information (e.g., Contacts) you have saved in Thank you for your purchase of "N-06C". your FOMA terminal. Even if the data may be For proper use of the N-06C, read this lost as a result of malfunction, repair, changing, manual before and while you use the N-06C. or other handling of the FOMA terminal, under no condition will DOCOMO be held liable for Before using the FOMA terminal any lost data saved in the FOMA terminal. The N-06C supports W-CDMA, GSM/GPRS, It is recommended that you save your and wireless LAN connectivity. important data into microSD cards. Because a FOMA terminal operates using radio Your FOMA terminal is the same as a PC. frequencies, it cannot be used inside a tunnel, Depending on the applications or other items underground, in a building or other locations that you install, the operation of your FOMA where radio waves do not reach the FOMA terminal may become unstable and your location terminal, in locations with weak radio wave or personal information saved on the FOMA condition, or outside of the FOMA's service terminal may be disseminated on the Internet area. The FOMA services may not be available and used improperly. You should therefore on high upper floors of high-rise apartments thoroughly check the provider and operation or buildings, even if you can see no status of an application before using it. obstructions around you. On occasion, your Operation of your FOMA terminal may calls may become disconnected even in areas become unstable if original product with strong signal, even if you are not moving, information contained in it is altered or or even if all four antenna icons are displayed. deleted. Under no condition will DOCOMO be Note that because the FOMA terminal operates held liable for any resulting inconvenience. on radio frequencies, your calls are at risk of This manual gives descriptions assuming use being intercepted by the third party. However, of the DOCOMO UIM. the W-CDMA, GSM/GPRS system automatically scrambles all calls through a private call feature. SIM unlocking Therefore, even if the third party successfully Your FOMA terminal supports SIM intercepts your call, they will only hear noise. unlocking. Unlocking the SIM enables use of The FOMA terminal operates on radio other-brand SIM cards. frequencies by converting voice into digital SIM unlocking can be requested at any signals. If the caller moves into an area of DOCOMO shop. adverse radio wave condition, the digital Separate charges apply for SIM unlocking. signal may not be restored accurately, and the Services, functions, etc. are limited when voice received in the call may differ slightly using other-brand SIM cards. DOCOMO does from the actual voice. not guarantee operation under such The FOMA terminal has FOMA Plus-Area and conditions. FOMA HIGH-SPEED Area support. For details on SIM unlocking, refer to the NTT DOCOMO website. Supplied Accessories and Optional Accessories
■■Supplied accessories
N-06C (with warranty and N-06C Quick Start Guide Battery Pack N28 Contents/Notes back cover N54) (Japanese)
Desktop Holder N34 microSDHC card (8 GB)* (with manual) (sample)
* This has been attached to the FOMA terminal when purchased.
1 Contents/Notes FOMA microUSB Adapter N01 Earphone Adapter microUSB cable for PC for charging (with manual) (sample) connection (with manual) (sample)
■■Optional accessories FOMA AC Adapter 01/02 (with warranty and manual)
2 About This Manual Viewing the operations manual in the FOMA terminal Notes When Reading Tap "Instruction Manual" and launch the instruction manual application to see Contents/Notes In this manual, operations are simplified as operation methods in the FOMA terminal. follows. Some functions can be activated from the Description Operation screen explaining about it. On the Home Tap m on the Home The latest information on this manual can screen, m ▶ screen, tap "Setting", and be downloaded at the NTT DOCOMO "Setting" ▶ then tap "Call settings" website. "Call settings" • User's Manual (PDF file) Download Please note that "N-06C" is called the "FOMA http://www.nttdocomo.co.jp/support/ terminal" in this manual. trouble/manual/download/index.html If you use a FOMA card, "UIM" should be * The URL and manual contents are subject to read as "FOMA card" in this manual. change without prior notice. Display examples used in this manual are images for explanation only and may be different from the actual display. This manual assumes the settings configured when you purchased the terminal, so the views and operation on your FOMA terminal may differ if you have changed the settings. The screens shown as examples in this manual are displayed when "English" is set for m ▶ "本体設定" (Setting) ▶ "言語とキーボード" (Language & keyboard) ▶ "言語を選択" (Select language). Set "English" for "言語を選択" (Select language) in advance. The reproduction or reprinting of all or part of this manual without prior permission is prohibited. The contents of this manual are subject to change without prior notice. 3 Supplied Accessories and Optional Accessories···················· 1 About This Manual····························································· 3 Notes on using N-06C························································· 6 Contents/Notes Contents Precautions (Always follow these directions)························ 7 Handling Precautions························································ 21 Waterproof Function························································· 27
Getting Part Names and Functions········34 Settings Wireless & Networks················82 Started UIM·········································36 P.82 Call Settings·····························88 P.34 microSD Card··························37 Sound······································88 Battery Pack·····························38 Display·····································88 Charging·································39 eco mode································89 Turning Power ON and OFF······44 Location & Security··················89 Switching the Screen Display Applications·····························92 Orientation······························44 Accounts & Sync······················93 Basic Operations······················44 Privacy·····································93 Initial Settings··························46 Storage····································94 Home Screen···························51 Search·····································94 Reading the Status Bar·············53 Language & Keyboard··············94 Application List Screen·············56 Voice Input & Output···············95 Using the Search Function········63 Accessibility·····························96 Task Manager··························63 Date & Time····························96 Text Entry·································64 About Phone···························96 Calling/ Making/Receiving Calls············70 Email/ Email·······································98 Network Call Log···································72 Browser sp-mode Mail···························99 Services Contacts (Phonebook)··············73 P.98 Gmail·······································99 P.70 Available Network Services·······76 SMS·······································102 Google Talk····························103 Browser·································104
4 Multimedia Camera··································109 Appendix/ Introduction to Options and P.109 Gallery···································112 Index Related Devices······················143 Music Player···························112 P.143 Troubleshooting (FAQs)··········143 Warranty and After-Sales Infrared Data Exchange··········115
File Contents/Notes Service···································148 Management Bluetooth Communication·····116 Updating Software·················151 P.115 Connecting to a PC················117 Major Update························158 Using PC Link·························117 Main Specifications················160 Applications Android Market·····················120 Specific Absorption Rate (SAR), P.120 docomo market·····················122 etc. of Mobile Phones············163 GPS·······································123 Export Administration 1Seg······································126 Regulations····························167 Osaifu-Keitai··························130 Intellectual Property Right······167 ToruCa···································132 Index·····································171 Clock·····································133 Calendar································134 Calculator······························134 Quickoffice····························135 iD設定アプリ (iD appli)············135 News & Weather····················135 Days······································136 Topics····································136 Using Overview of International Overseas Roaming (WORLD WING)·······137 P.137 Services Available Overseas····137 Check Before Using Your Terminal Overseas··················138 Network Settings for Use Overseas································140 Making/Receiving Calls while at Destination····························141
5 Notes on using N-06C When the memory capacity of a microSD card or the FOMA terminal become nearly The FOMA terminal does not support full, running applications may not function accessing i-mode sites (programs), i-αppli, correctly. If this happens, delete some of Contents/Notes etc. your saved data. Google applications and service content Set the screen lock password to ensure the may change in the future without prior security of your FOMA terminal for its loss. notice. → P.89 The FOMA terminal automatically performs Refer to the Google Inc. terms of usage communication for synchronizing data, regarding services that Google provides. checking the latest software version, Also refer to the respective terms of usage maintaining connection with the server, for other web services. etc. Also, operations such as downloading When using the UIM (blue), you cannot applications and viewing videos cause a use the FOMA terminal overseas. If you large volume of packet to be transmitted want to take the FOMA terminal with you, and incurs high communication charges. visit a docomo Shop Service Counter to Subscription to packet flat-rate service is have the UIM replaced. highly recommended. If your FOMA terminal is lost, change your Public mode (Drive mode) is not supported. password of each account using a PC to Setting the phone to Silent mode does not prevent other persons from using Google mute sounds (playback of video or music, services such as Google Talk, Gmail, alarm, etc.) other than the ringtone and Android Market, as well as Twitter and notification sounds. mixi. You can update the software of your The FOMA terminal does not support FOMA terminal. → P.151 service providers other than sp-mode, Updates for quality improvement of FOMA mopera U or ビジネスmoperaインターネッ terminals and operating system (OS) ト (Business mopera Internet) (only PPTP is upgrades may be applied. Such an update supported for VPN). or upgrade may cause applications you are A subscription to sp-mode is required to using to be unusable or have unexpected use Wi-Fi access points. errors.
6 By default, security is not configured for Precautions (Always follow Wi-Fi access points. Configure security if required. these directions) Packet communication charges for using
Wi-Fi access points differ depending on ■■To ensure that you use your FOMA Contents/Notes your fee plan. A flat-rate packet rate is terminal correctly, read "Precautions" strongly recommended. carefully before use. Keep this manual When using a flat-rate packet rate, all after reading for future reference. packet communication (including browser, ■■The precautions must be observed at email, etc.) using a Wi-Fi access point, even all times since they contain when a Wi-Fi-compatible device is not information intended to prevent the connected, is handled as communication bodily injury or damage to property. with a connected external device such as a ■■The following symbols indicate the PC. Be sure to disable the Wi-Fi access different degrees of injury and damage point as soon as communication with the that may occur if the information Wi-Fi-compatible device ends. provided is not observed and the For details on charges during use, refer to: FOMA terminal is used incorrectly: http://www.nttdocomo.co.jp/english/ Indicates that death or serious bodily injury DANGER may result directly and immediately from improper use. Indicates that death or WARNING serious bodily injury may result from improper use. Indicates that death or CAUTION serious bodily injury may result from improper use.
7 ■■The following symbols indicate specific 4. Precautions for the Adapter (including directions: Charger Adapter) and Desktop Holder ...... P.15 5. Precautions for the UIM ...... P.17 Indicates that it is prohibited. Contents/Notes 6. Precautions for Use Near Electronic Don't Medical Devices ...... P.17 1. Precautions for the FOMA terminal, Indicates that it must not be Battery Pack, Adapter (including disassembled. No disassembly Charger Adapter), Desktop Holder and UIM (Common) Indicates that you must not
No wet hands touch it with wet hands. DANGER Do not use, keep or leave the Indicates that it must not be used devices in locations subject to high near water, which means that Don't temperatures, such as near fire, No liquids you must not let it become wet. indirect sunlight or inside a car on Indicates that it is an a hot day. Doing so may cause fire, burns, or instructionbased compulsory injury. Do conduct (must be acted). Indicates that you must unplug Do not put the devices in a microwave oven or pressurized the power cord from the Don't container. Unplug outlet. Doing so may cause fire, burns, injury ■■ Safety precautions are explained in the or electric shock. following categories: Do not disassemble or modify the 1. Precautions for the FOMA terminal, equipment. Battery Pack, Adapter (including Charger No disassembly Doing so may cause fire, burns, injury Adapter), Desktop Holder and UIM or electric shock. (Common)...... P. 8 2. Precautions for the FOMA terminal...... P.10 3. Precautions for the Battery Pack...... P.13
8 Do not allow the devices to Do not cover or wrap the devices become wet with liquids, such as with bedding, etc. while in use or No liquids water, drinking water or pet urine. Don't charging. Doing so may cause fire, burns, injury Doing so may cause fire or burns. Contents/Notes or electric shock. For waterproof function, refer to the Make sure to turn off the FOMA following: terminal and stop charging before Do → P.27 "Waterproof Function" you get close to the places like a gas station where a flammable gas Use the battery pack and adapter is generated. (including charger adapter) Doing so may cause the gas to ignite. Do specified by NTT DOCOMO for the Turn off the power, when you use FOMA terminal. Osaifu-Keitai at a gas station (if the Failure to observe this precaution may Osaifu-Keitai lock is set, turn the cause fire, burns, injury or electric power off after the lock is released). shock. If something unusual happens, such as unusual odor, overheating, WARNING Do discoloration or deformation during use, charge or storage, be Do not throw the FOMA terminal sure to: or expose it to strong shocks. • Unplug the power cord from the Don't Doing so may cause fire, burns, injury power outlet or the cigarette or electric shock. lighter socket. Do not place electrically conductive • Turn off the power. objects (wires, pencil leads, etc.) in • Remove the battery pack from Don't contact with the charging terminals the FOMA terminal. or external connector terminal. Do Failure to observe these precautions not insert those materials inside may cause fire, burns, injury or electric the terminal. shock. Doing so may cause fire, burns, injury or electric shock.
9 CAUTION Pay special attention when you use Do not leave the devices on a slope the FOMA terminal connected to Do or unstable surface. the adapter (including charger Don't adapter) for a long period. Contents/Notes The devices may fall and cause injury. If you use a game or watch 1Seg Do not leave the devices in humid, programs for a long time while dusty or hot places. charging, the temperature of the Don't Doing so may cause fire, burns or FOMA terminal, battery pack or electric shock. adapter (including charger adapter) may rise. If your child uses the FOMA If you touch the warm part of these terminal, instruct him/her on how devices for a long period of time, it Do to use it. Check if he/she always may cause redness, itch, skin irritation uses the FOMA terminal correctly or low temperature burns depending as you instruct. on your constitution or physical Improper usage could result in bodily condition. injury. 2. Precautions for the FOMA terminal Keep the FOMA terminal out of young children's reach. WARNING Do A young child may try to swallow it or suffer injury. Do not direct the infrared data port towards your or another person's Don't eyes. Doing so may cause eye injury.
Do not direct the infrared data port towards consumer equipment with Don't infrared devices during infrared communication. Doing so may cause malfunction of the infrared devices and result in an accident.
10 Do not turn on the light near a Please turn off your FOMA terminal person's eyes. Especially when when inside an airplane, hospital, Don't photographing infants, maintain at Do or other area where use is least 1 m. prohibited. Contents/Notes The light may affect eyesight. Also, this The terminal may adversely affect may dazzle or surprise him/her and electronic or medical equipment. cause injury. Follow the instructions provided by the medical facility for the use of mobile Do not put fluids such as water or phones. substances such as pieces of metal Use of the phone in an airplane is Don't or flammable materials into the prohibited, and be punished by law. UIM slot or microSD card slot inside However, to enable use inside an of the FOMA terminal. airplane such as by using a non- Doing so may cause fire, burns, injury emission setting, follow the or electric shock. instructions of the airline before using.
Do not turn on the light against Make sure to hold the FOMA the car drivers, etc. terminal at a safe distance from Don't Doing so may interfere with driving Do your ear when you talk with the and cause a traffic accident. speaker ON or the ring tone sounds. Also, when you play games or music with an earphone/ microphone etc. connected to the FOMA terminal, adjust the volume properly. Too large a volume may lead to defective hearing. Also, hearing difficulties may cause an accident.
11 If you have a weak heart, take If the display or camera lens is precautions when setting the broken, be careful with the broken Do Vibrator or Ring volume. Do glass and any exposed FOMA Failure to observe this precaution may terminal parts. Contents/Notes affect your heart. A protective film is used for the display, and a plastic panel is used for the If you are wearing electronic camera lens surfaces to avoid glass medical devices, ask the scattering. However, touching broken Do manufacturer or sales agent or exposed parts may cause injury. whether the devices can be affected by radio waves before using your FOMA terminal. CAUTION The terminal may adversely affect The display has a protective film electronic medical devices. on its surface. It helps you ensure Don't Please turn off the power near safety even when the display gets electronic equipment that contains damaged due to a fall or shock Do high-precision mechanisms or (shatterproof hardened glass). Do handles delicate signals. not remove or scratch the The terminal may interfere with the protective film. operation of sensitive electronic If you use the FOMA terminal with the equipment. protective film removed, you may get * Electronic equipment to watch out injured if the display becomes for: damaged. Hearing aids, implanted pacemakers, Do not swing the FOMA terminal ICDs and other electronic medical by its antenna, strap or other parts. devices; fire alarms, automatic doors, Don't The terminal may strike you or others and other automatically controlled around you, resulting bodily injury. apparatus. Users of implanted pacemakers, ICDs, Do not use the damaged FOMA and other electronic medical devices terminal. are advised to ask the manufacturer or Don't Doing so may cause fire, burns, injury sales agent whether or not these or electric shock. devices can be affected by radio waves. 12 When using motion sensor, make There may be cases where the sure you are in a safe place, hold customer's physical condition or Don't the FOMA terminal securely, and Do predisposition leads to itchiness, do not shake it more than rashes, or sores. If this occurs, Contents/Notes necessary. immediately stop using the FOMA Failure to observe this precaution may terminal and see a doctor. cause injury. Material used in each part → P.19 "Material list" If the display is broken and the liquid crystal leaks, do not touch it When viewing the display, keep a Don't with your face, hands, etc. proper distance between your eyes Failure to observe this precaution may Do and it in a bright place. cause loss of eyesight or damage to Failure to observe this precaution may your skin. If the liquid crystal comes impair your vision. into your eyes or mouth, immediately rinse with clean water and see a doctor. 3. Precautions for the Battery Pack If the liquid crystal adheres to your skin or clothing, immediately wipe it off ■■Refer to the information shown on the with alcohol and wash with soap and battery pack label to check the type of water. battery pack. Display Battery type Before using your FOMA terminal Li-ion00 Lithium-ion in a vehicle, ask the manufacturer Do or sales agent whether the DANGER operation of the vehicle can be affected by radio waves. Do not place metal items such as In some types of vehicle, using the wires in contact with the charging FOMA terminal may interfere with the Don't terminals. Also, do not carry or store operation of the vehicle's electronic the battery with metal items such as equipment. In this case, stop using the necklaces. FOMA terminal immediately. Doing so may cause the battery pack to ignite, explode, overheat or leak.
13 WARNING Check the orientation of the battery pack before attaching it. If Never use the battery pack if it has Don't you have difficulty attaching it to fallen to have something abnormal the FOMA terminal, do not put Don't Contents/Notes such as deformation and damage. excessive pressure on the battery. Failure to observe this precaution may Failure to observe this precaution may cause the battery pack to ignite, cause the battery pack to ignite, explode, overheat or leak. explode, overheat or leak. If the battery pack leaks or emits Do not throw the battery pack into an unusual odor, stop using it fire. Do immediately and move it away Don't Doing so may cause the battery pack from any flame or fire. to ignite, explode, overheat or leak. The battery fluid is flammable and could ignite, causing a fire or Do not puncture the battery pack, explosion. hit it with a hammer or step on it. Don't Doing so may cause the battery pack Keep your pets away from the to ignite, explode, overheat or leak. battery pack as they may Do accidentally bite it. If battery fluid etc. comes into Failure to observe this precaution may contact with your eyes, do not rub cause the battery pack to ignite, Do your eyes but immediately rinse explode, overheat or leak. your eyes with clean water and see a doctor. Failure to observe this precaution may CAUTION result in loss of eyesight. Do not dispose of used battery packs with ordinary garbage. Don't Doing so may cause fire and create an environmental hazard. Put insulation tape on the terminals of used battery pack and return it to a docomo Shop or Service Counter, or dispose of the battery pack in accordance with your local regulations. 14 Do not use or charge the wet Do not use the AC adapter or battery pack. desktop holder in humid locations Don't Doing so may cause the battery pack Don't such as a bathroom. to ignite, explode, overheat or leak. Doing so may cause fire, burns or Contents/Notes electric shock. If the battery pack leaks, do not touch battery fluid etc. with your The DC adapter must be used only Do face, hands, etc. in vehicles with a negative ground. Failure to observe this precaution may Don't Do not use the adapter in vehicles cause loss of eyesight or damage to with a positive ground. your skin. If the battery fluid etc. Doing so may cause fire, burns or comes into your eyes or mouth or it electric shock. adheres to your skin or clothing, immediately rinse with clean water. In Do not touch the adapter the case that it comes into contact (including charger adapter) when Don't with your eyes or mouth, see a doctor you see lightning or hear thunder. immediately after rinsing. Doing so may cause electric shock.
4. Precautions for the Adapter Do not short-circuit the charging (including Charger Adapter) and terminals when the adapter is Don't plugged into the power outlet or Desktop Holder cigarette lighter socket. WARNING Also, do not let the charging terminals contact with your body Do not use the adapter (including (hand, finger, etc.). charger adapter) if its power cord Doing so may cause fire, burns or Don't is damaged. electric shock. Doing so may cause fire, burns or Do not put heavy objects on the electric shock. power cord of the adapter Don't (including charger adapter). Doing so may cause fire, burns or electric shock.
15 When plugging/unplugging the AC If the fuse in the DC adapter blows, adapter into/from the power always replace it with the specified Don't outlet, make sure that no metallic Do type of fuse. straps or other metallic objects are Failure to observe this precaution may Contents/Notes caught between the plug and the cause fire, burns or electric shock. Refer socket. to the respective manuals for the Metallic objects may cause fire, burns information on the specified fuse. or electric shock. Wipe off any dust on the plug. Do not touch the power cord of Failure to observe this precaution may the adapter (including charger Do cause fire, burns or electric shock. No wet hands adapter), desktop holder or the power outlet with wet hands. When plugging the AC adapter Doing so may cause fire, burns or into the power outlet, make sure Do electric shock. to insert it firmly. Failure to observe this precaution may Use the specified voltage and cause fire, burns or electric shock. current. Use the AC Adapter for Do Global use to charge the battery Always grasp the adapter overseas. (including charger adapter) when Do Using the adapters with incorrect unplugging the plug from the voltage may cause fire, burns or power outlet or cigarette lighter electric shock. socket. Do not pull the cord itself. AC Adapter : AC 100V Failure to observe this precaution may DC Adapter : DC 12V/24V cause fire, burns or electric shock. (specific to vehicle with negative Unplug the adapter from the ground) power outlet or cigarette lighter AC Adapter for Global Use : Unplug socket when the adapter will be AC 100V to 240V (household AC left unused for a long period. outlet only) Failure to observe this precaution may cause fire, burns or electric shock.
16 WARNING If water or other liquid gets into the adapter, immediately unplug it Take care of the following inside Unplug from the power outlet or cigarette hospitals. lighter socket. Do • Do not take your FOMA terminal Contents/Notes Failure to observe this precaution may into an operating room, intensive cause fire, burns or electric shock. care unit (ICU), or coronary care unit (CCU). Unplug the adapter from the • Turn off the power inside hospital power outlet or cigarette lighter wards. Unplug socket before cleaning it. • Turn off the power even in hospital Failure to observe this precaution may lobbies, waiting rooms, and cause fire, burns or electric shock. corridors if electronic medical devices may be in use near you. 5. Precautions for the UIM • For use inside medical institutions, please follow the instructions given CAUTION at individual locations.
Be careful with sharp edges when Turn off the power in crowded places removing the UIM. such as peak-hour trains if implanted Do Do Sharp edges may cause injury. pacemakers and ICDs may be in use near you. Radio waves emitted by the FOMA 6. Precautions for Use Near Electronic terminal may adversely affect Medical Devices implanted pacemakers and ICDs when used in close proximity. ■■According to the Guidelines on the Use of Radio communication Equipment such as Cellular Telephones - Safeguards for Electronic Medical Equipment established by the Electromagnetic Compatibility Conference Japan.
17 A person with an implanted pacemaker or ICD should use or Do carry the FOMA terminal at a distance more than 22 cm from the Contents/Notes site of implantation. Radio waves emitted by the FOMA terminal may adversely affect implanted pacemakers and ICDs when used in close proximity.
Electronic medical devices other than implanted pacemakers and Do ICDs may also be used outside hospitals. Users of electronic medical devices are advised to ask the manufacturer whether these instruments can be affected by radio waves. Radio waves from the FOMA terminal can adversely affect electronic medical devices.
18 ■■Material list Part Material/Surface treatment Outer case Display surface Nylon resin, Tin deposition/UV coating Battery side Nylon resin/UV coating Contents/Notes Display panel Hardened glass, Shatter-proof film/UV coating Camera ring Aluminum/Alumite painting Camera panel Acrylic, Polycarbonate composite resin/UV coating Light and infrared data port panel PC resin/UV coating Display-side panel Acrylic, Polycarbonate composite resin/UV coating Keys Power key PC resin, Tin deposition/UV coating (body color
19 Part Material/Surface treatment 1Seg antenna Upper portion cover ABS resin/UV coating Middle portion Stainless alloy Lower portion Nickel titanium alloy Contents/Notes Base hinge Stainless alloy Mounting Stainless alloy Screw Stainless alloy Battery pack recess Recess surface Side: Nylon resin Bottom: Polyester film UIM tray POM resin Battery terminal Terminal connector LCP resin Terminals Phosphor-bronze/Gold plating Battery pack Battery pack Resin: PC resin (terminal) Label: PET resin Terminals Glass epoxy resin/Gold plating
20 Handling Precautions Occasionally clean the connection terminals with a dry cotton swab, etc. Soiled connectors may result in poor General Notes connections, loss of power, or incomplete
charging. Wipe with dry cloth or cotton swab. Contents/Notes N-06C is waterproof, however, do not Do not place the FOMA terminal near an air allow water to seep in the FOMA conditioning vent. terminal. Also, do not allow accessories Condensation may form due to rapid changes and options to get wet. in temperature, and this may cause internal The battery pack, adapter (including charger corrosion and malfunction. adapter), desktop holder and the UIM are not waterproof. Do not use them in a humid place Do not put excessive pressure on the such as a bathroom or in the rain. If you carry FOMA terminal or battery. the FOMA terminal on your body, perspiration Do not put the FOMA terminal in a bag filled may corrode the internal parts of the FOMA with many objects or sit down with it in a hip terminal and cause malfunction. Note that if pocket. trouble is diagnosed as exposure to water or Excessive pressure may result in malfunction other liquid, repair of the FOMA terminal may or damage to the display, internal circuit or not be covered by the Warranty or repair may the battery pack, etc. not be possible. Repair, when possible, is not Also, if an external device is connected to the covered by warranty and is carried out at cost. external connector terminal (earphone/ microphone terminal), excessive pressure may Wipe with a soft, dry cloth (such as an result in malfunction or damage to the eyeglass cleaning cloth). connector. • Rubbing the display of the FOMA terminal with a dry cloth may scratch the display Do not scratch the display with metallic surface. objects. • The display surface may be stained if Doing so may cause scratches, malfunction or moisture or dirt is left on it for a long period. damage. • Never use chemicals such as alcohol, Read the separate manuals supplied with thinners, benzene or detergents as these the battery pack and adapter (including agents may erase the printing on the FOMA charger adapter) carefully. terminal or cause discoloration.
21 Handling the FOMA Terminal It is normal for the FOMA terminal to become warm while being used or Do not forcefully push or use a pointed charged. This is not a malfunction. Keep object (nails, ballpen, pin, etc.) on the using it. touch panel. Contents/Notes Do not leave the camera exposed to Doing so may damage the touch panel. direct sunlight. Avoid using the FOMA terminal in Doing so may discolor or burn the extremely high or low temperatures. components of the camera. The ambient temperature of the room should Keep the external connector terminal be 5˚C to 40˚C (limited to the temporary use (earphone/microphone terminal) cap in a bathroom etc. when temperature is above closed when not in use. 36˚C) with humidity of 45% to 85%. Failure to observe this precaution may cause Reception may be affected if you use malfunction due to dust or water getting in. your FOMA terminal near a land-line Do not use FOMA terminal with the back phone, television, or radio in use. Use the cover removed. FOMA terminal away from such devices. Doing so may cause the battery pack to fall Please keep a separate record of the out, or cause malfunction or damage. information you have registered in your Do not insert hard, sharp objects into FOMA terminal. earpiece/speaker. Please be aware that DOCOMO bears no Doing so may cause malfunction or damage obligation or responsibility in the event that to the FOMA terminal. data is altered or lost. Do not remove the microSD card or turn Do not drop the FOMA terminal or expose off the power while in use. it to strong shocks. Doing so may cause data loss or malfunction. Doing so may cause malfunction or damage. Do not let magnetic cards, etc. come close Ensure the FOMA terminal does not come to FOMA terminal parts. near a fire (stove, etc.) or fall from a The magnetic data in cash cards, credit cards, tabletop due to the vibrator. telephone cards, floppy disks, etc. may be When connecting an external device to erased. the external connector terminal Do not let strong magnetic objects come (earphone/microphone terminal), do not close to the FOMA terminal parts. insert at an angle or pull the cord. Strong magnetic objects may cause Doing so may cause malfunction or damage. misoperation.
22 Handling the Battery Pack Handling the Adapter (including The battery pack is consumable. Charger Adapter) Battery life varies depending on usage The ambient temperature of the room conditions, etc., but it is time to change should be 5˚C to 35˚C. Contents/Notes battery packs when the usage time has Do not charge the battery pack: become extremely short even though the • In a humid, dusty or unstable place battery pack has been fully recharged. • Near a land-line phone, TV or radio In this case, please purchase a new battery It is normal that the adapter (including pack. charger adapter) become warm while The ambient temperature of the room charging. Keep using it. should be 5˚C to 35˚C. Do not use the DC adapter to charge the The available operating time of the battery when the car engine is not battery pack depends on the conditions running. of usage and battery pack. Doing so may drain the car battery. Depending on the usage condition, the If you use an electrical outlet with an battery pack may inflate slightly when unplugging-protection mechanism, follow the battery life is almost over. This is not the instructions of the manual for the a malfunction. outlet. Do not store the battery pack in the Do not expose the adapter to strong following cases: shocks. Do not deform the charging • The battery is fully charged (immediately terminal. after the charging is complete) Doing so may cause malfunction. • The battery has run out (the phone cannot power on) Handling the UIM The performance and life of the battery pack may deteriorate. Do not apply excessive force to the UIM It is recommended that you store the battery when attaching/removing it. pack with around 40% battery level. Note that the warranty does not cover damage caused by inserting the UIM into another type of IC card reader or writer. Always keep the IC part clean. Wipe with a soft, dry cloth (such as an eyeglass cleaning cloth). 23 Please keep a separate record of the Please be aware that DOCOMO is not information you have registered in your responsible for data leak when making UIM. data communications using Bluetooth. Please be aware that DOCOMO bears no You can use a headset, handsfree, audio,
Contents/Notes obligation or responsibility in the event that object push, serial port, and phonebook data is altered or lost. access on the FOMA terminal. The audio/ To preserve the environment, bring video remote control may be available for discarded UIM to a docomo Shop or audio. (Only on compatible Bluetooth Service Counter. devices) Do not damage, scratch, unnecessarily Frequency band touch, or short-circuit the IC. The following are frequency bands that the Doing so may cause data loss or malfunction. FOMA terminal's Bluetooth function uses: Do not drop the UIM or expose it to ① ② ③ strong shocks. Doing so may cause malfunction.
Do not bend the UIM or place a heavy ④ object on it. Doing so may cause malfunction. ① 2.4 : The radio equipment uses the 2400 MHz band. Do not put a label or sticker on the UIM ② FH : Modulation scheme is the FH-SS when attaching it to the FOMA terminal. system. Doing so may cause malfunction. ③ 1 : The estimated interference Using the Bluetooth® Function distance is 10 m or less. ④ : The full band between 2400 To secure the Bluetooth communication MHz and 2483.5 MHz is used security, the FOMA terminal supports the and the band of the mobile security function compliant with identification device cannot be Bluetooth standards, but the security may avoided. not be sufficient depending on the setting. Concern about the communication using the Bluetooth function.
24 ■■Bluetooth cautions When Using a Wireless LAN The operating frequency band of this A wireless LAN (WLAN) uses radio waves equipment is used by industrial, for transmission, and thereby has the scientific, consumer and medical benefit of allowing a LAN connection Contents/Notes equipment including microwave ovens, anywhere in an area reachable by radio premises radio stations for identifying waves. Conversely, eavesdropping by a mobile units used in the manufacturing third party or wrongful intrusion are lines of plants (radio stations requiring possible if security settings are not a license), specified low power radio configured. Users are recommended to stations (radio stations requiring no use discretion and configure security license) and amateur radio stations settings before using. (hereinafter referred to as "another Wireless LAN station"). Do not use wireless LAN near magnetic 1.Before using this terminal, confirm devices such as electrical appliances or AV/OA that "another station" is not being devices, or in radio waves. operated nearby. • Magnetism or radio waves may increase 2.In the event of this terminal causing noises or disable communications (especially harmful radio wave inter ference when using a microwave oven). with "another stations", promptly • When used near TV, radio, etc., reception interference may occur, or channels on the change the operating frequency or TV screen may be disturbed. stop radio wave emission by turning • If there are multiple wireless LAN access off the power, etc. points nearby and the same channel is used, 3.If you have further questions, please search may not work correctly. contact General Inquiries on the last Frequency band page of this manual. The frequency band used by the WLAN device is indicated on a label in the battery pack recess of the FOMA terminal. The following figure explains the indications on the label.
25 ① ② ③ ④ ■■2.4 GHz device cautions The operating frequency band of this WLAN device is used by home electrical ⑤ appliances such as microwave ovens, as Contents/Notes ① 2.4 : This radio equipment uses the well as industrial, scientific and medical 2400MHz band. equipment including private radio ② DS : Modulation scheme is the DS-SS stations on factory premises for system. identifying mobile units used in ③ OF : Modulation scheme is the OFDM manufacturing lines (radio stations system. requiring a license), specified low power ④ 4 : The estimated interference radio stations (radio stations requiring distance is 40m or less. no license), and amateur radio stations ⑤ : The full band between (radio stations requiring a license). 2400MHz and 2483.5MHz is 1.Before using the device, confirm that used and the band of the mobile private radio stations for identifying identification device can be mobile units, specified low power avoided. radio stations and amateur radio • Available channels vary depending on the stations are not being operated country. nearby. • For use in an aircraft, contact the airline 2.If the device causes harmful radio beforehand. • For use of WLAN in a foreign country, the interference to private radio stations country may have limitations on such as for identifying mobile units, locations where you can use it. Before using immediately change the frequency WLAN in a foreign country, confirm the band or stop use, and contact available frequencies, laws, regulations, and "docomo Information Center" other conditions for use of WLAN of the described on the last page of this country. manual for crosstalk avoidance, etc. (e.g. partition setup). 3.If the device causes radio interference to specified low power radio stations or amateur radio stations, contact "General Inquiries" described on the last page of this manual. 26 Handling the FeliCa Reader/Writer Use the Bluetooth function only in Japan. The Bluetooth function of the FOMA terminal The FeliCa reader/writer function of the complies with radio standards of Japan and is FOMA terminal handles delicate signals certified. You may be punished if you use it that require no radio station license. overseas. Contents/Notes The 13.56 MHz frequency band is used. If Use the FeliCa reader/writer function only there is another reader/writer near the in Japan. FOMA terminal, keep enough distance The FeliCa reader/writer function of the FOMA between the FOMA terminal and the terminal complies with radio standards of reader/writer. Also, make sure that there Japan. You may be punished if you use it is no radio station using the same overseas. frequency band nearby. Waterproof Function Cautions *1 *2 Do not use the altered FOMA terminal. N-06C is waterproof to IPX5 and IPX7 Using an altered device is a violation of standards if the external connector the Radio Law. terminal cap is closed as well as the back A "Technical Conformity Mark " affixed on cover is securely attached. the manufacturer's specification sticker certifies *1 IPX5 means that the N-06C continues to that the FOMA terminal meets technical function as a phone after being sprayed regulations for specified radio equipment based from all directions with 12.5 liters of water on the Radio Law. If you remove the screws per minute from a 6.3 mm diameter nozzle and alter the inside of the FOMA terminal, the for at least 3 minutes, from a distance of technical regulations conformity certification approx. 3 meters. becomes invalid. Do not use the FOMA *2 IPX7 means that the N-06C retains phone terminal with the certification invalid, as it is a functionality after slowly immersing in still, violation of the Radio Law. room-temperature tap water to a depth of Be careful when using the FOMA terminal 1 meter and leaving it there for 30 minutes while driving. before bringing it out of the water. A penalty may be imposed for holding a You can talk or watch 1Seg without an mobile phone while driving. However, umbrella in the rain (approx. 20 mm of rain exceptions are made in case of emergency, in an hour). such as to safeguard injured persons or to maintain public safety. 27 Do not attach/remove the back cover or do Things to keep in mind not open/close the external connector Before use, ensure that you securely close the terminal cap when your hands are wet or external connector terminal cap and back when your FOMA terminal has water drops cover so that they are completely attached. If Contents/Notes on it. any fine dirt (fine fibers, hairs, or sands) is You can rinse the FOMA terminal by between the cap/cover and the FOMA immersing and slowly moving in tap water terminal, water could enter the inside of the of room temperature filled in a bowl, or FOMA terminal. rinse it with hands under light running Do not use the FOMA terminal (operate keys, water from the faucet. etc.) under water. • Rinse the FOMA terminal with the back Do not spray or immerse the FOMA terminal cover securely attached while covering in liquids other than water of room the external connector terminal cap to temperature as illustrated below. prevent it from opening.
Do not immerse or drop in pool water or Soap/Detergent/ Sea water Pool sea water. Bath powder You can use the FOMA terminal in the bathroom. However, do not immerse it in the bathtub. • Never immerse the FOMA terminal in hot spring water or water containing soap, Hot spring Sand/mud detergent or bath powder. • Avoid using the FOMA terminal for a long time in the bathroom.
28 Opening/closing the external connector Attaching/removing the back cover terminal cap ■■Removing ■■Opening Hold the FOMA terminal, then
Hook your finger on the slot and open the cap in 1 Contents/Notes the direction of arrow. hook your finger on the slot and remove in direction ① without too much force
Slot
■■Closing Slot Insert the tab on the back of the cap in direction ①, then close the cap by pressing securely in direction ②. Tab
29 ■■Attaching NOTE Insert the tab on top of the back When attaching the back cover, make sure that 1 the UIM, the microSD card and the battery pack cover into the FOMA terminal are attached securely. If the UIM or microSD card
Contents/Notes slot, slide it in direction ① and is not securely inserted, the battery pack sits on push it down securely in the UIM or microSD card which causes a gap direction ② between the FOMA terminal and the back cover when attaching the back cover. The waterproof Slot function might deteriorate because of the gap. To maintain waterproof function, Tab replacement of parts is required once every 2 years regardless of whether the FOMA terminal appears normal or abnormal. DOCOMO replaces the parts as a chargeable service. Bring the FOMA terminal to a repair counter specified by DOCOMO.
Securely push the areas illustrated by and make sure that there is no space between the Important notices back cover and the FOMA terminal. If the FOMA terminal gets wet with water or other liquids with the external connector NOTE terminal cap or the back cover open, the When removing the back cover, make sure that liquid may get inside the FOMA terminal you drain water and wipe moisture off the causing electric shock or malfunction. Stop FOMA terminal. using the FOMA terminal, turn off the power, When attaching the back cover, make sure that remove the battery pack and contact a repair no dust or dirt adheres to the back cover counter specified by DOCOMO. (especially to the rubber packing). The external connector terminal cap and the Water might enter the inside of the FOMA rubber packing of the back cover play an terminal unless you attach the back cover important role in maintaining waterproof securely. function. Do not remove or scratch them.
30 Also, prevent dust from adhering to them. If Do not put the FOMA terminal in hot water, the external connector terminal cap and the use it in a sauna or apply hot air flow (from a rubber packing of the back cover is damaged hair dryer etc.) to it. or deformed, replace it at a repair counter Do not leave the FOMA terminal on the sand
specified by DOCOMO. at a beach. Contents/Notes Do not insert sharp objects through the gap • Sand might enter the mouthpiece or of the external connector terminal cap or back earpiece/speaker and result in smaller sound. cover. Doing so may damage the rubber • Using the FOMA terminal with water or packing and allow water to seep in. sand still in it may result in unclear sound. If the back cover is damaged, replace it. Water • Water may enter by the external connector may seep into the inside of the FOMA terminal cap or back cover even if only a tiny terminal through a damaged section causing amount of sand lodges in them. electric shock, corrosion of the battery pack, Do not poke the mouthpiece or earpiece/ or other malfunctions. speaker with cotton swabs or sharp objects. Do not leave the FOMA terminal with water The waterproof function may deteriorate. drops. In cold places, water may freeze and Do not leave the FOMA terminal wet. Doing cause malfunction. so may cause short-circuit of the supply To prevent condensation, do not bring the terminal. FOMA terminal from a cold place to a The FOMA terminal does not float on water. bathroom, etc. without letting the FOMA Do not drop the FOMA terminal. Scratches terminal get back to room temperature. may lead to lowered waterproof capability. Do not apply water flow stronger than allowed Do not leave water on the mouthpiece or (e.g., such water flow that gives you pain when earpiece/speaker. If water adheres to the applied to your skin directly from a faucet or FOMA terminal, the volume during a call or shower head). Doing so may cause malfunction ringtone may be decreased or sound quality though N-06C is waterproof to IPX5 standard may deteriorate. In such a case, drain the (P.27). water to recover the function. Do not wash the FOMA terminal in a washing DOCOMO does not guarantee all operations machine etc. under actual use conditions. Malfunctions Accessories and options are not waterproof. deemed to be caused by inappropriate When watching 1Seg etc. with the FOMA operation by the customer are not covered by terminal attached to the provided desktop the warranty. holder, do not use it in a bathroom, shower room, kitchen or washroom even if it is not connected to the AC adapter. 31 Even if the back cover is securely attached, Wipe the surface of the FOMA removing the sealing shown may result in a 1 terminal with a clean dry cloth, loss of waterproof capability. Do not remove sealing. etc. Contents/Notes
Sealing
Draining water when the FOMA terminal gets wet When the FOMA terminal gets wet, drain the water following the steps below. If water adheres to the mouthpiece or earpiece/speaker, the volume of the other Securely hold the FOMA terminal party's voice or melody may be decreased or 2 and shake it approx. 20 times sound quality may deteriorate. In such a case, until there is no more water drain the water following the steps below and dry the FOMA terminal in open air to recover splattering the function.
32 3 Softly press a clean dry cloth etc., When charging the battery on the FOMA terminal to wipe Accessories and options are not waterproof. off water remaining in the Check the following before and after charging.
mouthpiece or earpiece/speaker Contents/Notes • Do not wipe off water remaining in gaps Make sure that the FOMA terminal is not wet. directly with a cotton swab etc. If the FOMA terminal is wet, thoroughly drain the water and wipe off with a clean dry cloth, etc. before placing it on a provided desktop holder or opening the external connector terminal cap. When the external connector terminal cap is opened for charging, close the cap securely after charging. It is recommended that the desktop holder be used for charging to prevent water from seeping in through the external connector terminal. • Never try to charge the battery pack when the FOMA terminal is wet. • Do not touch the AC adapter or desktop holder with wet hands. Doing so may cause electric shock. • Use the AC adapter or desktop holder in a Thoroughly wipe off water place free from water splashes. Do not use 4 drained from the FOMA terminal them in a bathroom, shower room, kitchen, washroom and other places subject to water. with a clean dry cloth, etc. Otherwise, it may cause fire or electric • Water, if any, remaining in the FOMA shock. terminal may leak out after wiping off.
33 Getting Started
Part Names and Functions Getting Started
34 ❶Earpiece (receiver)/Speaker GPS antenna section* ❷Proximity/Illuminance sensor emark • Hides tappable icons on the touch panel • Put the mark close to the reader when using when your face comes close to the touch おサイフケータイ (Osaifu-Keitai). → P.130 panel. This prevents you from unintentionally 1Seg antenna activating functions when you are engaged • For 1Seg reception. → P.126 in a call. UIM slot
• Detects the brightness around the terminal • Set the UIM to the slot. → P.36 Getting Started and automatically adjusts the illuminance of microSD card slot the display. → P.88 • Set the microSD card to the slot. → P.37 ❸Notification LED Back cover ❹Display (Touch panel) FOMA antenna* • Allows you to scroll the screen on the display Charging terminal or tap to select objects. → P.44 * The antennas are built-in. To ensure good ❺mMenu key → P.45 signal quality, avoid covering the antenna ❻hHome key → P.45 section with your hands. ❼rBack key → P.45 NOTE ❽Mouthpiece/microphone Do not put labels or stickers on the sensors. ❾Power key • Powers the terminal on/off or sets it in sleep mode. Using an earphone
External connector terminal External connector terminal cap Switch • Provides connections to the adapters, microUSB (to answer an earphone/headphone, and PC, etc. plug incoming call) *Surface with tabs Strap slot downwards Infrared data port
• Serves for infrared data exchange. → P.115 Microphone Light Earphone plug • Turn it on when taking a picture as needed. Earphone adapter Volume key • Adjusts the volume. Camera Plug the earphone plug into the • You can use the camera to take videos or 1 Earphone Adapter (sample) photos. → P.109 switchside terminal 35 Open the external connector Hold the tab to pull out the tray 2 terminal cap (P.29), and plug 1 the microUSB terminal of the Tab Earphone Adapter into the external connector terminal
Getting Started UIM UIM is an IC card that stores your phone number and other information. Some functions are not available if the UIM is not inserted. For details on the UIM, refer to the manual for the UIM. You should insert/remove the UIM after turning the power off and removing the Place the UIM on the tray, setting battery pack (P.39). Hold the FOMA 2 the IC surface on the upside terminal firmly with both hands. Notch
IC
UIM
UIM slot
Set UIM with the IC surface (gold-colored) up 36 Insert the tray to the end If saved data becomes lost or is altered, 3 DOCOMO will not be held liable. Do not turn off the power while the microSD NOTE card is being accessed. The data may be Forceful insertion/removal may damage the UIM destroyed or the card may no longer function or tray. properly. Data from another device saved to microSD
microSD Card card may not be displayable or playable on Getting Started the FOMA terminal. Data saved to microSD You can save data in the FOMA terminal card from the FOMA terminal may also not be to microSD card or transfer data on a displayable or playable on another device. microSD card to the FOMA terminal. You should insert/remove a microSD card after The N-06C supports a microSD card of up turning the power off and removing the to 2 GB, and a microSDHC card of up to battery pack (P.39). Hold the FOMA 32 GB (as of June 2011). Refer to the terminal firmly with both hands. following website for information on the ■■Attaching latest operation check information, Insert the microSD card into the including microSD card manufacturers and 1 microSD slot until it is locked card capacities. Note that microSD cards • Insert the microSD card into the slot other than those given may not function. slowly and straight in with the metal • http://www.n-keitai.com/ (in Japanese only) contacts facing down. When the card is Given information is the result of operation fully inserted, it is locked. checks, and is not a guarantee of operation. Handling precautions
Make sure to format microSD card on N-06C. You may not be able to use microSD card formatted on another terminal or PC. → P.94 Note that formatting the microSD card deletes all data in it. Be sure to make a backup or otherwise microSD card separately store data saved to a microSD card.
37 ■■Removing Battery Pack Push the microSD card in, and 1 then release it Use the Battery Pack N28 for the FOMA terminal. • The microSD card comes out slightly. You should insert/remove the battery pack Note that the card may jet completely out of its slot. after turning the power off. Hold the FOMA terminal firmly with both hands. Getting Started 2 Hold the microSD card at its Attaching/removing the back cover groove, and then pull it straight → P.29 out slowly ■■Attaching With the product name label on the 1 battery pack facing up, insert in the ❶ direction ① by hooking the tabs on the battery pack in the slots in the FOMA terminal, so that the "▲" ❷ marks and terminals are aligned. Then set the battery pack in the direction ②
Hook tabs in slots
Align "▲" marks
38 NOTE Charging Do not press forcefully if tabs are not hooked in slots. May break tabs. The battery pack is not fully charged at time of purchase. Be sure to fully charge ■■Removing before use. Push the tab of the battery pack 1 ■■Battery charging in the direction ① then pull it up • For more details, see the respective manuals in the direction ② of the FOMA microUSB Adapter N01 for Getting Started charging, the FOMA AC Adapter 01/02 (optional), the FOMA AC Adapter 01 for Global use (optional) and the FOMA DC Adapter 01/02 (optional). • The FOMA AC Adapter 01 is only compatible with AC 100V. The FOMA AC Adapter 02 and the FOMA AC Adapter 01 for Global use are compatible with AC 100V-240V. • The AC adapter has an AC 100V plug (Japanese specification). When using an AC 100-240V adapter overseas, you will need a Tab converter plug adapter compatible with local voltage. Do not charge the FOMA terminal using a travel transformer. • You must attach the battery pack to the FOMA terminal if you want to charge using the FOMA microUSB Adapter N01 for charging and an AC or DC adapter. • Do not force the connector when inserting/ pulling it out. Instead, insert or pull it out slowly. • If you start charging when the battery pack is empty, you may not be able to power ON the FOMA terminal for a while.
39 • Depending on conditions of use, charging Continuous call time may stop before the battery level is 100%. If FOMA/3G: Approx. 250 minutes this happens, charge again after exiting all GSM: Approx. 250 minutes functions in use. Before charging again, first Continuous 1Seg viewable time disconnect the FOMA terminal from the FOMA microUSB Adapter N01 for charging or Approx. 300 minutes microUSB cable for PC connection (sample), ■■Battery pack life
Getting Started and then reconnect it. • The battery pack is a consumable accessory. ■■Charging time (estimate) The usage time of the battery per 1 charge Charging time is an estimate of the time decreases gradually each time the battery is required to charge a completely empty battery recharged. pack while the FOMA terminal is powered off. • When the usage time from 1 charge becomes FOMA AC Adapter 01/02 Approx. 170 minutes about half of a new battery pack, the life of the battery pack is assumed to be almost over. FOMA DC Adapter 01/02 Approx. 170 minutes We recommend that you replace the battery * Charging when connected to FOMA microUSB ahead of time. Adapter N01 for charging. • If you view 1Seg while charging for a long ■■Usage time when fully charged period, the life of the battery pack may (estimate) decrease. Usage time differs with the operating To prevent damage to the environment and the condition of the battery environment, bring used battery pack. packs to a docomo service Usage time for the FOMA terminal becomes counter, a docomo agent or a shorter as you view 1Seg or use GPS. recycling center. Continuous standby time FOMA/3G ■■Waterproof capability • Stationary (Automatic):Approx. 340 hours • The battery pack, AC adapter, and supplied • Moving (3G static): Approx .260 hours desktop holder are not waterproof. You must • Moving (Automatic): Approx. 180 hours not charge when the FOMA terminal is wet. GSM • To prevent intrusion of water from the • Stationary (Automatic):Approx. 220 hours external connection terminal, charging is recommended using the desktop holder.
40 • After charging is completed, securely close Holding the desktop holder, the external connection terminal cap. 3 insert the FOMA terminal as Otherwise, water may enter. shown in direction ① , then Charging with the desktop holder attach firmly in direction ② After charging is complete, hold 4 down the desktop holder, then Getting Started With the arrow remove the FOMA terminal side facing up tilting it in the direction of the arrow
Notification Connector LED 100V AC power outlet
Plug
Desktop Holder N34
FOMA AC Adapter 01/02 Plug the connector of the AC 1 adapter (optional) horizontally to the terminal on the back of the provided desktop holder Plug the AC adapter into the 2 outlet
41 Charging with the AC adapter/DC 2 Open the external connector adapter terminal cap (P.29), and plug Be sure to refer to the manuals for the FOMA the microUSB plug of the FOMA AC Adapter 01/02 (optional) or FOMA DC microUSB Adapter N01 for Adapter 01/02 (optional). charging horizontally into the Notification LED External connector FOMA terminal's external Getting Started terminal cap connector terminal ■For DC Adapter (option) microUSB To AC100V • Insert the microUSB plug horizontally plug outlet To lighter socket with the engraved side facing up. *Surface with the engraved Insert the AC adapter plug mark upwards 3 Connection horizontally into the power Power terminal plug FOMA microUSB Connector outlet/the DC adapter plug into Adapter N01 for Plug AC the car’s lighter socket charging adapter Release clips When charging is completed, Insert the AC adapter/DC adapter 4 remove the microUSB plug 1 connector horizontally into the horizontally from the FOMA connection terminal of the FOMA terminal and close the external microUSB Adapter N01 for connector terminal cover (P.29) charging Remove the AC adapter/DC • Insert the connector with the engraved 5 adapter connector horizontally side facing up horizontally into the connection terminal with print side facing from the connection terminal of up. the FOMA microUSB Adapter N01 for charging Remove the AC adapter from the 6 power outlet/DC adapter from the car’s lighter socket
42 Charging with the microUSB cable 3 When charging is completed, for PC connection remove the microUSB plug You can charge your FOMA terminal by horizontally from the FOMA connecting the FOMA terminal and a PC terminal and close the external with the microUSB cable for PC connection connector terminal cover (P.29) (sample). Remove the USB plug 4 horizontally from the PC USB Getting Started Surface with engraved mark upwards port NOTE Notification LED turns red while charging, green microUSB cable for when the battery level is over 90%, and off when PC connection (sample) charging is complete. Open the external connector terminal cover When you begin charging, such as when the battery is depleted, the notification LED may not Open the external connector immediately light. However, charging has 1 terminal cap (P.29), and plug started. the microUSB plug of the
43 Turning Power ON and OFF The display may not switch depending on the content being displayed. ■■Turning power ON Operate on the terminal, setting the display vertically to the ground. If the display is 1 Press the power key for 2 placed horizontally to the ground, the seconds or longer display orientation does not switch. • When turning power on for the first time, You can disable screen rotation by pressing
Getting Started the initial setting screen appears. m in the Home screen ▶ "Setting" ▶ → P.46 "Display", and unmarking the "Auto- • The Home screen appears. → P.51 rotate screen" checkbox. ■■Turning power OFF Basic Operations 1 Press the power key for 1 second or longer ▶ "Power off" ▶ "OK" Operate the FOMA terminal by directly touching the touch panel (display). Sleep mode ■■Precautions on using the touch panel When the power key is pressed or the FOMA The touch panel has been designed for light terminal is not operated for a specified finger touches. Do not press it hard with your duration of time, the display turns off and finger or with sharp objects (nail, ballpoint pen, the terminal enters sleep mode. pin etc.). Pressing the power key quits sleep mode. The following user actions may cause the touch panel not to work properly. They may also cause Screen lock malfunction. When you turn power on or quit sleep • Touching the screen with gloved hands mode, the touch panel is locked. • Touching the screen with the tip of a Drag to to unlock the screen. fingernail • Placing a foreign object on the screen Switching the Screen Display • Sticking a protective sheet or seal on the Orientation screen • Touching the screen when it is wet The FOMA terminal can automatically • Touching the screen with sweaty or wet switch the display orientation by sensing fingers the sideway tilt of the body.
44 Tap Flick Select or run items. Quickly scroll in direction you want to view.
Touch the panel Quickly slide your then release your finger and release it.
finger. Getting Started
■■Touch and hold Pinch with two fingers In some screens, continuing to touch the touch panel displays a menu. Zoom in or zoom out.
Slide Touch the touch Scroll up/down/left/right in direction you want panel with two to view. fingers, then slide them apart or together. Slide your finger while touching the touch panel. The WmWhWr keys You can use the mhr keys mainly ■■Drag for the following. Slide your finger while touching an item (icon, • m : Display the menu available for the etc.) to move it. current screen. Depending on the current screen, menu items may include search, settings, or delete options. • h : Display the Home screen. You can return to the Home screen when using a function. Touch and hold to carry out task management.
45 • r : Go back one screen. Use when you Check the explanation for want to return to the previous screen. 7 updating software ▶ "Next" Initial Settings "Completed" 8 • Tap "Go To the site NOW" to access the MEDIAS official website. Settings when power is first turned Setting an access point
Getting Started ON When the FOMA terminal power is first The access points (sp-mode, mopera U) turned ON, the following settings are required for connecting to the Internet are required. preset. You may add or change them as When the initial setting screen required. 1 The sp-mode is set as the default access point. appears, tap the language ▶ "次 へ" Configuring access point to be used 2 Check the displayed content ▶ From the Home screen, m ▶ "Next" 1 "Setting" ▶ "Wireless & To configure a Google account, networks" ▶ "Mobile networks" 3 "Settings" ▶ "Access Point Names" ▶ tap • Follow onscreen instructions to configure the radio button for the access a Google account and back up data, and point then tap "Next". Adding an access point 4 To use Google Location Service, mark the checkbox ▶ "Agree" ▶ From the Home screen, m ▶ "Next" 1 "Setting" ▶ "Wireless & To use GPS, mark the checkbox ▶ networks" ▶ "Mobile networks" 5 "Agree" ▶ "Next" ▶ "Access Point Names" To initialize Osaifu-Keitai, m ▶ "New APN" 6 "Initialize" 2 • Follow onscreen instructions to initialize Osaifu-Keitai, and then tap "Next". 46 3 "Name" ▶ enter the name of the sp-mode new network profile ▶ "OK" sp-mode is an ISP for NTT DOCOMO "APN" ▶ enter the access point smartphones. In addition to Internet 4 name ▶ "OK" connection, this also provides an email service that uses the same email addresses as Enter any other items requested i-mode (@docomo.ne.jp). 5 by your network operator sp-mode is a paid service that requires subscription. For details about sp-mode, refer Getting Started 6 m ▶ "Save" to the NTT DOCOMO website. mopera U NOTE Do not change MCC to anything other than mopera U is an NTT DOCOMO ISP. If you 440, or MNC to anything other than 10. If you have subscribed to mopera U, you can use do this, registered/added access points will no the Internet after making the simple longer display on the screen. If access points no settings. longer display due to the MCC and MNC mopera U is a paid service that requires settings being changed, you can either restore subscription. default settings or manually set the access points again. Setting mopera U m Initializing an access point From the Home screen, ▶ 1 "Setting" ▶ "Wireless & When you initialize an access point, it returns to its default settings. networks" ▶ "Mobile networks" ▶ "Access Point Names" 1 From the Home screen, m ▶ "Setting" ▶ "Wireless & 2 Tap to select the "mopera U (ス networks" ▶ "Mobile networks" マートフォン定額)" (Smartphone ▶ "Access Point Names" flat-rate)/"mopera U 設定" (mopera U settings) radio button 2 m▶ "Reset to default"
47 NOTE Wi-Fi settings Subscription to flat-rate packet communication Wi-Fi is a function that allows you to use service is required if you want to use "mopera email and the Internet, via access points for U (スマートフォン定額)" (Smartphone flat-rate). household/corporate networks or public For details on mopera U (Smartphone flat-rate), refer to the NTT DOCOMO website. wireless LAN services. "mopera U設定" (mopera U settings) is the ■■Radio wave interference with
Getting Started access point for setting mopera U. When you Bluetooth devices use the access point for setting mopera U, Since a Bluetooth device and a wireless LAN packet communication charges for setting do (IEEE802.11b/g/n) device use the same not apply. Note that you can only connect to the frequency ranges (2.4GHz), radio wave initial setting screen or the setting change screen for mopera U. For details on mopera U settings, interference may occur when the Bluetooth refer to the mopera U website. device is used near a device equipped with a wireless LAN. This may cause deterioration in the communication speed, noise and connection problems. If this occurs, take the following measures: Keep a distance of at the nearest 10 m from a wireless LAN device when you connect the Bluetooth device or the FOMA terminal. Turn off the Bluetooth device in case you should use the Bluetooth device within 10 m from the wireless LAN device.
Turning Wi-Fi ON to connect to a network From the Home screen, m ▶ 1 "Setting" ▶ "Wireless & networks" ▶ "Wi-Fi settings"
48 Mark the "Wi-Fi" checkbox • Again, keep touching the easy setup 2 • A scan for Wi-Fi networks begins button until the POWER LED is lit Orange automatically. A list of available networks on the access point. appears. • When the status bar shows , you are accessible to the Wi-Fi network. Tap the name of the Wi-Fi ■■WPS 3 network that you want to • Push Button Control method: Search for
connect to access points begins, so you should press Getting Started • To connect to a protected Wi-Fi network, the pushbutton on an access point itself enter the required information and tap or an access point’s setting screen. "Connect". Continue by following onscreen instructions. Connecting to a Wi-Fi network with • PIN method: Search for access points easy Wi-Fi settings begins. Continue by following onscreen When an access point-capable device supports instructions. When "PIN code" (Pin code "らくらく無線スタート" (Easy Wireless Setup) for WPS) appears on the FOMA terminal, and "WPS", you can easily complete required register the displayed number in the settings, including ESSID and the security access point. method. • When the status bar shows , you are accessible to the Wi-Fi network. 1 From the Home screen, m ▶ "Setting" ▶ "Wireless & Adding a Wi-Fi network manually networks" ▶ "Wi-Fi settings" For information on using an access point, refer to the manual for the access point. 2 Mark the "Wi-Fi" checkbox 1 From the Home screen, m ▶ "Wi-Fi Easy Settings" ▶ "Easy "Setting" ▶ "Wireless & 3 Wireless Setup"/"WPS" networks" ▶ "Wi-Fi settings" ■■Easy Wireless Setup 2 Mark the "Wi-Fi" checkbox • Keep touching the easy setup button until the POWER LED blinks in Green on "Add Wi-Fi network" the access point. 3
49 Enter the network SSID for the Enter the email address and 4 Wi-Fi network to be added, and 2 password ▶ "Next" then select the security (Open, • For an email account with preset provider WEP, WPA/WPA2 PSK, 802.1x information, settings for the send/receive mail servers are complete automatically. EAP) • For an email account without preset Enter additional security provider information, settings must be Getting Started 5 information as required ▶ "Save" completed manually. Contact your provider for settings information. Disconnecting a connected Wi-Fi Enter the account name and user network 3 name ▶ "Done" m From the Home screen, ▶ Setting a Google or other account 1 "Setting" ▶ "Wireless & By configuring a Google account, you can networks" ▶ "Wi-Fi settings" use Gmail, market, and other services. 2 Tap the connected Wi-Fi network From the Home screen, m ▶ ▶ "Forget" 1 "Setting" ▶ "Accounts & sync" ▶ Setting an Email account "Add account" Setting an email account provided by 2 Tap the type of account mopera U or any general providers, you can use email. Follow onscreen instructions to Obtain information required for completing 3 settings from your service provider configure the account beforehand. In the application list screen, 1 "Email" ■■To set an additional account ▶ m ▶ "Accounts" ▶ m ▶ "Add account"
50 Home Screen ■■To delete Home screens ▶ Touch and hold the thumbnail of the The Home screen is the starting screen for Home screen to delete ▶ drag it to the using applications. You can tap h to trash icon at the bottom of the screen and open the screen. release your finger ■■Repositioning Home screens Indicator ▶Touch and hold the thumbnail of the Home
Number of Home screen pages screen to reposition ▶ drag it to where you Getting Started and position want to move it and release your finger Widgets Adding an application shortcut to the Home screen Touch and hold the Home screen Application shortcuts 1
"Shortcut" Dock 2 ■■Adding a widget Launch browser ▶"Widget" Launch sp-mode mail Launch phone/call log, contacts ■■Adding an application group Open the application list screen (P.56) You can move the Home screen to a page on ▶ "Group" ▶ tap the group to add the right or left by sliding the screen. ■■Adding a web page (P.106) ▶ "Web page" ▶ tap the bookmark for Adding a Home screen the web page to add ▶ tap the update interval ▶ "OK" 1 From the Home screen, m ▶ "Home screen list" 3 Tap the shortcut that you want • Thumbnails of Home screens appear. to add " " • An application shortcut is added to the Home screen. 2 • You can add up to 12 Home screens.
51 Moving a shortcut 2 "Folder" 1 From the Home screen, touch and hold the shortcut that you want 3 Tap the type of folder that you to move want to create 2 Drag it to the desired position Adding a shortcut to a folder Getting Started and release your finger Shortcuts can only be added to the folder type • To move a shortcut to another page, drag "New Folder". the shortcut to the right or left edge of Touch and hold the shortcut you the screen, and the Home screen moves 1 to the right or left page. want to add to a folder Drag the shortcut to the desired Docking a shortcut 2 folder and release your finger From the Home screen, touch and • You can tap a folder to open it and 1 hold the shortcut to add access shortcuts. Drag it to the desired position in Renaming a folder 2 the Dock and release your finger Tap the folder that you want to • The shortcut changes places with the 1 icon where it is dragged to. rename NOTE 2 Touch and hold the title bar cannot change places. Enter a title ▶ "OK" Creating a folder on the Home 3 screen Add a folder for grouping shortcuts, a Deleting a shortcut or folder contacts folder, or other folder to the Home screen. Touch and hold the shortcut or 1 folder to delete 1 Touch and hold the Home screen
52 Drag it to the trash icon at the Reading the Status Bar 2 bottom of the screen and release your finger Notification icons for new information and status icons for FOMA terminal status Switching the Home screen are displayed in the status bar. Notification icons are displayed on the From the application list screen, left side, and the FOMA terminal status 1 "Homescreen Switcher" ▶ tap icons are displayed on the right side of Getting Started the Home screen to switch to the status bar. Status bar Changing the Home screen wallpaper 1 Touch and hold the Home screen Status icons 2 "Wallpaper" ▶ "Gallery"/"Live wallpapers"/"Wallpaper gallery"/ Icon Description "Wallpapers" ▶ tap the image to The battery needs to be charged / set ▶ "Set wallpaper" / / Battery level / The battery is • If you have selected "Gallery", select the charging image to set as wallpaper, and then drag * Signal status the trimming frame to where wallpaper * International roaming will be used. Out of service area Tap "Save" to set the wallpaper. • If you have selected "Live wallpapers", / * 3G communicating / available tap "Settings" depending on the / * GPRS communicating / available wallpaper to set the wallpaper. Airplane mode activated * Connected to Wi-Fi Bluetooth is ON / connected to / compatible device Synchronizing data
53 Icon Description Icon Description Osaifu-Keitai lock activated Music is playing UIM not inserted Unsecured Wi-Fi network found The alarm is set Newly received file via Bluetooth Speaker ON during call communication Microphone is mute USB is connected Getting Started / Silent mode with vibration ON/OFF / In call / On hold eco mode is ON Missed call GPS is positioning Data upload/send Enterable text type (hiragana / Data download/receive / / alphabet / numerals / smileys, Application installation completed / / emoticons, symbols, fixed phrases, Update of installed application character codes / T9 input) available * When a Google account is configured Some notification icons (synchronized), the icon appears blue, and undisplayed when not configured (not synchronized), grey. Sending/receiving data by infrared data exchange Notification icons Viewing 1Seg Icon Description Recording 1Seg New Gmail MEDIAS NAVI update notification New Email Software update notification New sp-mode mail Major software update New SMS message notification, updating Failed to send SMS PC Link is connected New Voice Mail message PC Link available New instant message PC Link confirmation message Upcoming calendar event Connected by USB PC Link Alarm is snoozed Tap searching Error/Alert message 54
: GPS function on/off → P.124 Icon Description No available space in phone : Bluetooth function on/off → P.82 Wi-Fi access point available : Wi-Fi function on/off → P.82
/ VPN is connected / Unconnected : Brightness level → P.88
Using the Notifications panel : Account auto-synchronization on/off → P.93 When a notification icon appears, you can Getting Started ③Shows the name of the network carrier open the Notifications panel to check a you are connecting to. message or event notification. ④Shows the name of the network carrier 1 Drag the status bar downwards that provides services. ① ⑤Tap this to delete the checkmarked (⑦) notifications and the notification icons displayed on the status bar. ② ⑥Shows the missed call log and other ③ ⑤ information such as completion of a ④ download. ⑦ ⑦Mark a checkbox for the notifications you ⑥ want to delete, and then tap ⑤; the notification icons are deleted. ■■Close the Notifications panel ▶ Drag bottom of Notifications panel to top
①Activates Tap search. → P.63 ②Tap the following icons to change the function status. / : Silent mode (vibration on/off) on/off → P.88
: eco mode on/off → P.89
55 Application List Screen "Edit name" ▶ enter the group 2 name ▶ "OK" The application list screen shows a list of ■■Changing a group color the applications installed in the FOMA ▶ "Change color" ▶ tap the color terminal in groups. ■■Deleting a group 1 From the Home screen," " ▶ "Delete" ▶ "Yes" Getting Started Adding a group From the application list screen, Group name/number of 1 m applications Tap the group to "Add group" show/hide application 2 icons. 3 Enter a group name ▶ "OK"
Applications Repositioning groups
■■Change to list display 1 From the application list screen, ▶ m ▶ "List view" touch and hold the group to • In list display, m ▶ "Tile view" to reposition change to group display. Drag it to where you want to Editing a group 2 move it and release your finger
Changing a group name From the application list screen, 1 touch and hold the group you want to change
56 Adding a group shortcut to the Home Adding an application shortcut to the screen Home screen From the application list screen, Touch and hold the application 1 touch and hold the group to add 1 you want to add on the ▶ "Add to home" application list screen ▶ "Add to home"
NOTE Getting Started "Recently" automatically displays the preceding Applications list eight applications used. Group names cannot be changed or deleted Applications Description with "Recently" or "Download Application". Osaifu-Keitai → P.130
Editing applications Music → P.112
Repositioning the applications Voice Search Your spoken words are recognized, then searched 1 Touch and hold the application in the Browser by Google you want to reposition on the search. application list screen Camera → P.109 Drag it to where you want to Calendar → P.134 2 move it and release your finger
Uninstalling an application Gallery → P.112 Touch and hold the application Google → P.63 1 you want to uninstall on the Search application list screen ▶ "Uninstall" ▶ "OK" ▶ "OK"
57 Applications Description Applications Description Koe no Use this service to record a 地図アプリ This application supports Takuhaibin voice message over the ("Chizu your outings using docomo phone, and notify the Appli" map map navi’s maps/ other party by SMS that application) navigation/train there is a recording. Using connections. Available free this application allows you of charge throughout the
Getting Started to simply record a voice trial period. message and play it back. Twipple You can easily use Twitter 書籍・コミック You can view topical through Twipple. E★エブリスタ electronic books and comics, TV → P.126 (E★ EVERYSTAR from original works by books/comics) professional writers and Calculator → P.134 celebrities to popular contents by ordinary persons. Phone → P.70 Viewing the works by professional writers and PhoneBookCopy You can use a microSD celebrities will be charged. card to copy contacts data Settings → P.82 between your and another FOMA terminal. Contacts sotomemo Edit photographs and data registered to a Google comments to create your account can also be copied own map. Great as a to your docomo account. memo tool when out and → P.75 about. Downloads Display a log of files downloaded with the browser. 旅比較ねっと Besides simul-searching (tabihikaku-net) vacation packages from travel agency web sites, you can use GPS to search nearby lodgings.
58 Applications Description Applications Description Phonebook This service allows you to ToruCa You can view, search, and backup back up Contacts data to update ToruCa including the Phonebook backup shop information and center automatically on a coupons. → P.132 regular basis, so you can Navigation → P.125 restore data if you have lost
your FOMA terminal or News & You can check news and Getting Started accidentally erased data. Weather weather forecast. → P.135 For details on Phonebook Video Camera → P.109 backup, refer to "ご利用ガ イドブック (spモード<スマー Browser → P.104 トフォン>編)" (Mobile Phone User's Guide Places → P.126 [sp-mode], in Japanese only). Homescreen → P.53 Talk → P.103 Switcher Pedometer You can use a pedometer. Clock → P.133
Market → P.120 ドコモ海外利用 Supports packet transmission (docomo while while overseas and settings/ overseas) confirmation of overseas マクドナルド Application allowing you to flat-rate packet service. (McDonald’s) use MacDonald’s member coupons and a locations docomo You can access docomo search feature. market market and search applications and movies. Maps → P.124 → P.122 Instruction The manual for your FOMA Email → P.98 Manual terminal. You can also launch functions directly Messaging → P.102 from the explanations. → P. 3
59 Applications Description Applications Description Melody Call This service plays a chosen BOOKストア This is an electronic book melody for a caller. You can 2Dfacto store where you can listen to and select, buy, (BOOK Store purchase and browse a and specify settings for 2Dfacto) variety of books such as melodies with Melody Call. literary books, popular Melody Call is a pay-for comics, famous business
Getting Started service requiring books. subscription. Days → P.136 mosimo Detects a subject’s camera movement and face and Evernote This service allows you to allows effects to be added. save various kinds of 楽天 Easily search for popular information, such as オークション fashion items and other goods website content, (Rakuten available on Rakuten Auction. photographed images, and Auction) memos, to a server for Contacts → P.73 searching and viewing when needed. In addition andronavi You can use "andronavi" to your FOMA terminal, which is an information site you can save and browse by NEC Biglobe, dedicated information from a PC or for Android terminals. other device. Creation of an Evernote account is ATOK → P.67 required to use this application. BeeTV BeeTV is a broadcast station for mobile phone. Gmail → P.99 You can view all programs of BeeTV by registering as paid member.
60 Applications Description Applications Description Gガイド番組表 With this application you MEDIAS Navigate get-in-shape and (G-GUIDE EPG) can view program guides WELLNESS health maintenance for terrestrial digital, BS programs. Choose training digital, and other broadcast and recording that suits services. You can search your likes, and keep up an programs by keyword, enjoyable health regimen.
genre, etc., book viewing/ Quickoffice → P.135 Getting Started recording of 1Seg programs, and use other spモードメー You can use an i-mode functions. → P.129 ル (sp-mode email address (@docomo. iD 設定アプリ iD is electronic money that mail) ne.jp) to send and receive (application allows you to pay for a email. → P.99 for iD purchase simply by holding Topics → P.136 settings) the FOMA terminal up to a reader in a store. You can Twonky Allows wireless playback easily set and start using Mobile on DLNA-compatible TV or iD. → P.135 Special audio of movies, ｉチャネル Distributes a variety of photographs, and music (i-Channel) information, including stored in a smartphone or weather and news. The downloaded over the latest information Internet. automatically received is To enjoy contents available displayed by a widget on over the Internet, an access the Home screen. point enabling connection i-Channel is a pay-for is required. service requiring YouTube You can watch/upload subscription. YouTube videos. Latitude → P.126
MEDIAS NAVI Connect to the manufacturer’s site "MEDIAS NAVI".
61 Widgets list Widget Description You can add widgets to the Home screen to Clock (world) Display the local time and use the following functions. the time for a specified city. Clock Add an analog clock. Widget Description (analog) Rate Places Display information for Clock (digital) Add a digital clock. nearby shops.
Getting Started Music (small) Display a simple music Docomo A widget that regularly control panel. Market obtains and displays the Music (large) Display a music control Widget latest docomo market panel that includes album information. cover images. News & Display news and weather Calendar Display upcoming events Weather forecast. (upcoming scheduled in the calendar. Call Logs A widget that displays a events) history of outgoing and Calendar Add a small-size calendar. incoming calls, allowing (small) you to make calls, add Calendar Add a large-size calendar. contacts, etc. (large) Photo Frame A widget that displays the Google Add a search box. → P.63 images in a specified Search album. Picture frame Add an image. Market Display information for Android Market. Soradas This widget displays the Days Display information for (small) day’s weather forecast. Days. Soradas This widget displays a ｉチャネル A widget that obtains and (large) four-day weather forecast. ウィジェット displays information for Twipple Add a Twipple shortcut. (i-Channel i-Channel. widget) Digital Clock A widget that displays a Latitude Display information for digital clock. Latitude. Topics Display information for Topics. 62 Widget Description ■■Searching by voice Web Page A widget that regularly ▶ " " ▶ say the search words clearly into obtains and displays a the microphone specified web page. • Not usable with some search items. YouTube Search and view YouTube. Using Tap search Make a search by tapping words that appear
NOTE on the screen you want to search. Getting Started Application/widget content and icon positions Open the Notifications panel, may change by performing either a software or 1 major update. " " Tap the text you want to search Using the Search Function 2 by on the screen ▶ "OK" You can search for contacts or • You can tap the text box and edit the text before searching. applications in the FOMA terminal, or search web pages. NOTE For information on search settings → P.94 Tap search has the following requirements for recognizing text. From the application list screen, 1 • Recognizable text: black kanji/alphabet/ "Google Search" katakana on a white background " " ▶ tap the search item • Recommended size: 20 to 40 dots 2 Some applications may be not displayed correctly in Tap search mode. Enter the search text ▶ "実行" 3 • Search results are displayed. Task Manager • After entering search text, search candidates are displayed. You can select a The Task manager shows the running candidate to search with. applications and allows you to switch to • Tap an application from a candidate to the one you want to use. It also allows launch the application. you to quit applications you do not use. Touch and hold h 1 • Running applications are displayed.
63 ■■To close an application ■■10-key keyboard ▶ " " This is an ordinary keyboard of mobile phones. ■■To close all applications ⑩ ▶ "Close all" ▶ "Yes" ⑨ ⑦ Tap the application that you ⑤ ⑤ 2 want to display ② ③ Getting Started NOTE ① ⑥ Running more than one application may consume more energy and make the operation of the terminal unstable. Doing so may cause ① / : Toggle the QWERTY keyboard applications to be terminated forcibly or slow and 10-key keyboard. down. → P.66 Change text to hiragana/kana/ Text Entry alphabet/etc. With the 10-key keyboard, changes The FOMA terminal has an onscreen text to kana/alphanumeric/etc. keyboard that is displayed in the screen. Also toggle half-width/full-width. Tap a text box on the screen to display ② ■QWERTY keyboard (Japanese Input Mode) the onscreen keyboard. Toggle enterable text in the order You can use the following two kinds of "Hiragana" → "Alphabet" keyboards. Touch and hold to display the ATOK menu. ■■QWERTY keyboard [ATOK Menu] This keyboard uses a PC keyboard layout. • "ATOK Settings": "Configuring text Enter Japanese in romaji. entry settings" → P.67 ⑩ • "Register Words": Add words. Added words are usable when converting kana to kanji. • "English Input Mode ⇔ Japanese Input Mode": Toggle entry modes. ⑧ ⑦ ■QWERTY keyboard (English Input Mode) ① ⑥ The ATOK menu is displayed. ② ③④ ⑤ 64 ② ■10-key keyboard (Japanese Input Mode) ⑧ Tap once to change the next character Toggle enterable text in the order to be entered to upper case ( ), tap "Hiragana" → "Alphabet"→ twice to lock in upper case ( ). Some "Numeral" symbols can also be entered. Touch and hold to display the ATOK ⑨ Display one character before (reverse). menu. ■10-key keyboard (English Input Mode) Undo one action before.
Toggle enterable text in the order Getting Started ⑩ Prediction candidates are displayed "Alphabet" → "Numeral" - when entering text, and you can tap Touch and hold to display the ATOK to enter text. menu. ③ Enter a space. Selecting the 10-key keyboard entry Convert entered text. method Select a text entry method for the 10-key ④ Change the keyboard to symbol entry. keyboard. ⑤ Move the cursor. When converting, On a text entry screen, touch and change the conversion range. 1 / hold / ▶ "ATOK Settings" ▶ "Software keyboard" ▶ "Input ⑥ Enter a line feed or confirm entered mode" text. "Numeric keypad input"/"Gesture When there is a text entry box such as 2 input"/"Flick input"/"T9 input" for Contacts, completes entry and moves to the next item. ■■Numeric keypad input Tap the key with the desired character assigned When entering text for a web page or on repeatedly until you get to the character. for search words, runs the function of the text box. ■■Gesture input ⑦ Delete text to the left of the cursor. Keep touching on the key with the desired For the 10-key keyboard, you can also character; the associated gesture guide set "Character delete key" (P.67) to (characters) is displayed around the key. Slide delete text to the right ( ). your finger to the target character without releasing it from the panel.
65 You can slide the finger you tapped downward Example: To enter "春" once or twice to display a gesture guide with a ▶ Tap "は" then "ら" voiced consonant, unvoiced consonant, or small Tap "春" displayed in the kana (during alphabet entry, toggle upper/lower prediction candidates. case). • If desired text does not Example: To enter "ぱ" appear in the candidates, tap and
Getting Started enter the reading. • To enter a voiced/ unvoiced consonant, tap Slide . downward twice • To toggle English and Japanese, tap / . ■■Flick input • You can tap to Keep touching on the key with the desired toggle display of character; the associated flick guide (characters) candidates between "漢 is displayed on the key. Flick your finger toward 字／かな" (kanji/kana). the target character without releasing it from A "はる" candidate appears the panel. in "変換" (convert), so tap After flick input, you can tap once or twice "春". Prediction candidates to enter a voiced consonant, unvoiced from "はる" appear in "予 consonant, or small kana. 測" (prediction). ■■T9 input • To change the Tap each key with a desired character once, and conversion range, tap then select the desired text from the displayed / . prediction candidates to enter it. Entering with the smiley/emoticon/ symbol palette Smileys are available only with sp-mode mail. 1 In a text entry screen, tap
66 2 " "/" "/" " 2 Select any item: • The palette for the keyboard is displayed. Software keyboard ■■Entering from fixed phrases/ Keypad sound······Set sound for when character codes keys are pressed. ▶" "/" " Keypad vibration······Set vibration for ■■Quoting Contacts data when keys are pressed. 電話帳／ ダイレクト ▶ " " ▶ " ATOK " ▶ Getting Started Input mode → P. 65 tap the contact ▶ checkmark the item to quote ▶ "OK" Multi-tap input······Enable numeric keypad input for both gesture input and Switching to the Android keyboard flick input. Mark the "Enable auto cursor moving" To enter alphabet, you can also change to checkbox to move the cursor to the the Android keyboard and enter text. right after a period of no entry during Japanese cannot be entered with the Android numeric keypad input. Also set how keyboard. quickly the cursor moves. Mark the In a text entry screen, touch and "Enable multi-tap input when gesture / 1 hold a text box flick input" checkbox to automatically move the cursor during both gesture 2 "Input method" ▶ "Android input and flick input. keyboard" The setting for auto cursor moving • Tap "ATOK" to enter Japanese. changes with each "Input mode" setting. Configuring text entry settings Character delete key······When Configure settings for text entry including deleting text, set to delete to the left of sound/vibration for key operation and text the cursor ("BS ( )") or the right ("CLR size. ( )"). In a text entry screen, touch and Gesture guide······Set whether the 1 hold / ▶ "ATOK Settings" gesture guide is displayed at entry by gesture. Mark the checkbox to display the gesture guide. You can set the time length before the guide is displayed.
67 Flick guide······Set whether the flick Use half-width space······Set to enter guide is displayed at entry by flicking. half-width spaces also when entering Flick Sensitivity······Set the sensitivity Japanese text. of character selection for a character Initializing learning data······Reset input by flicking. learning data and smiley/emoticon/ Auto alphanumeric select······Set to symbol entry panel log. enter in half-width letters when Design Getting Started switching to the QWERTY keyboard Font size······Set the font size of the from the 10-key keyboard. candidate list. Show numeric keys (vertical number of lines to display (vertical screen)······Set to display numeric keys screen) ······Set the number of lines for when displaying the QWERTY keyboard the candidate list on the vertical screen. in the vertical screen. When set not to display, enter numbers by flicking. number of lines to display (horizontal screen)······Set the number Show numeric keys (horizontal of lines for the candidate list on the screen)······Set to display numeric keys horizontal screen. when displaying the QWERTY keyboard in the horizontal screen. When set not Tools to display, enter numbers by flicking. Dictionary utility······Maintains the Entering/Converting user dictionary. Input prediction······Set to display the Common phrase utility······Maintains prediction candidates for conversion. user-registered fixed phrases. Common phrases that use smileys are not Showing prediction candidates displayed in text boxes that do not before next input······Set to predict support smileys. and display candidates for words to follow confirmed (converted) text. Initializing settings → P. 69 Selectable when the "Input prediction" checkbox is marked. Auto space insert······Set to automatically put a space following a word after it is confirmed in English Input Mode. 68 Initializing text entry settings You can restore the "ATOK Settings" to their defaults. In a text entry screen, touch and 1 hold / ▶ "ATOK Settings" ▶ "Initializing settings" ▶ "OK" Getting Started NOTE Learning data, user-registered words, and user-registered fixed phrases are not initialized.
69 Calling/Network Services
Making/Receiving Calls ■■Muting your voice to the other party ▶ "Mute" Making a call • Tap to toggle the mute ON/OFF. From the application list screen, ■■Using the Bluetooth function 1 ▶ "Bluetooth" "Phone" • Tap to toggle the function ON/OFF. Calling/Network Services Enter the phone number Available when connected to a Bluetooth 2 • If you enter a wrong number, tap to device compatible with your headset, delete the number. handsfree, etc. • Enter "186"/"184" before entering the When the call is finished, " " number to notify/not notify your number, 4 for that call only. NOTE ■■Entering a push tone (pause) ▶ m ▶ "Add 2-sec pause"/"Add wait Tap " " or touch and hold "1" to make a call to 1417 (Voice Mail service). pause" 3 " " ■■Emergency call ■■Adjusting the call volume Emergency call Phone number ▶ Press the volume key Police emergency 110 ■■Muting the microphone Fire brigade/Ambulance 119 emergency ▶ "Hold" • Tap "Unhold" to cancel call hold. Maritime distress call 118 • To place a call on hold, a subscription to Call Waiting service is required. ■■Putting the other party on the speaker ▶ "Speaker" • Tap to toggle the speaker ON/OFF.
70 Your FOMA terminal supports "Emergency NOTE Location Report". When you have set PIN1 code entry and Airplane Calls made to emergency service organizations mode, you need to enter the PIN1 code to make (e.g. by dialing 110, 119 or 118) disclose an emergency call. information on the caller's location to the When you have locked the screen, you can make organization receiving the call. an emergency call without drawing screen The location information and phone number unlock pattern and entering PIN code for each are not disclosed when, before each individual screen. On each screen, tap "Emergency call". call made, "184" or another blocking prefix is The "Emergency Dialer" screen appears; you can dialed first. If the information is deemed make phone calls only to the emergency phone necessary for the protection of life, etc., this numbers. Calling/Network Services information may be acquired by the In Japan, the 110, 119, and 118 emergency organization being called. numbers cannot be dialed from the FOMA Locations/timing planned for adoption of this terminal when the UIM is not set to it. feature vary according to the status of the In Japan, the 110, 119, and 118 emergency preparations by the relevant emergency numbers cannot be dialed by tapping service organizations. "Emergency call" from the PIN code input screen When calling 110, 119 or 118 from the FOMA on startup. For details on PIN code, see "Security terminal, first say you are calling from a codes used with the FOMA terminal" (P.90). mobile phone, give your number, and state your location clearly, because the police or fire Making an international call department may call you back for (WORLD CALL) confirmation. WORLD CALL is an international phone Also, do not move around when making the service that can be used from DOCOMO call. Do not turn off the power immediately mobile phones. Customers who have after ending the call, but leave it turned on subscribed to the FOMA service would also for ten minutes or so, so that you can receive have automatically subscribed to "WORLD a call. CALL" at the same time (excepting those Depending on the area you are calling from, who have declined it). you may not be connected with the nearest For details on WORLD CALL, refer to police or fire department, etc. DOCOMO "International Services website". From the application list screen, 1 "Phone"
71 Touch and hold "0" Call Log 2 • A plus sign "+" appears. Enter the country code → area You can check the outgoing/incoming calls history. 3 code (city code) → recipient's phone number ▶ " " From the application list screen, 1 "Phone" ▶ "Call log" NOTE If the area code begins with "0", omit "0". ① However, "0" may be required for calling some countries or areas, such as Italy. ③ ② Calling/Network Services Receiving a call ④ When a call is received, drag 1 to (to the right) ■■Declining a call ▶ Drag to (to the left) When the call is finished, " " 2 ①The names of other parties to/from which calls were made are displayed. NOTE ②Make a call. If you decline an incoming call when Voice Mail ③Log icons are displayed. service or Call Forwarding service are set to : Outgoing call "Activate", the call is forwarded to the Voice : Incoming call Mail service center or the designated forwarding : Missed call number. ④A series of calls to/from a same party are displayed as one entry with . The number in parentheses is the number of logged calls.
72 ■■Adding a phone number from the Contacts (Phonebook) call log to Contacts ▶ Touch and hold the entry you want to You can add data such as phone numbers, add ▶ "Add to contacts" ▶ "Create new email addresses, and SNS (Twitter, contact" ▶ enter required items ▶ "Save" Facebook, mixi) account information to • If multiple accounts are registered, select Contacts. You can easily make a call from one from the accounts. Contacts or check SNS update information. • If you want to select a contact already Communication charges may be incurred registered, just select the contact. when you enter or obtain information from ■■Deleting the log SNS.
▶ m ▶ "Clear call log" ▶ "OK" Calling/Network Services • To delete individual entries, touch and 1 From the application list screen, hold an entry to delete and then tap "Contacts" "Remove from call log". ② ① ③
④ ⑥
⑤ ⑧ ⑦
⑨
⑩ ⑪ ⑫ ⑬ ①Add a new contact. Enter required items such as name, number, and email address, and then tap "Save". • When several accounts are registered, select the account to add to.
73 ②Display contacts in the selected group. ■■Importing from/exporting to a microSD ③Enter keywords to search for contacts. card/the UIM ④Your profile (MyProfile) is displayed. ▶ m ▶ "More" ▶ "Import/Export" ▶ Select You can tap to edit MyProfile or add a any item: Twitter, Facebook, or mixi account. Import from SIM card······Load contacts from ⑤Contacts (profiles) are displayed. → P.74 the UIM to the FOMA terminal. ⑥Registered SNS icons are displayed. ⑦An icon is displayed for contacts collected Export to SIM card······Save contacts from the together (P.75). FOMA terminal to the UIM. ⑧Jump to the tapped or dragged index. Import from SD card······Load contacts from a ⑨You can select an image and tap the microSD card to the FOMA terminal. Calling/Network Services displayed icon to make a call, create Export to SD card······Save all contacts from the email, or go to an SNS site. FOMA terminal to a microSD card. ⑩Display the call log. → P.72 ⑪Display the screen for entering a phone Share visible contacts······Send all viewable number. → P.70 contacts via Bluetooth transmission, email, etc. ⑫Display contacts added to Favorites and contacts you call often. Displaying the profile screen You can add contacts to Favorites from the profile screen. 1 Tap the name of the contact you ⑬Check SNS update information for want to display in the contacts registered contacts. screen You can update SNS information or go to Twitter/Facebook or mixi pages. ① ③ ■■Deleting contacts ② ▶ m ▶ "More" ▶ "Delete contact" ▶ checkmark contacts you want to delete ▶ ④ "Done" • To delete individual contacts, touch and hold a contact to delete and then tap "Delete contact".
⑤
74 ①Image and name are displayed. From the application list screen, You can select an image tap the displayed 1 "PhoneBookCopy" icon to make a call, create email, or go to an • When you first use PhoneBookCopy, you SNS site. need to accept a "License agreement". ②Edit a contact (profile). ③Tap to set adding to Favorites ON/OFF. ■■Exporting Contacts data stored at ④Registered information is displayed. docomo account to a microSD card Displayed items differ with the registered ▶ "エクスポート" (export) ▶ "開始" (start) content. ▶ "OK" Depending on the registered content, you can ■■Importing Contacts data from a tap or touch and hold an item to do actions microSD card to your docomo Calling/Network Services such as make a call, send email and SMS, or account launch Google Maps or Calendar. ▶ "インポート" (import) ▶ tap the contacts ⑤Check contacts history or display SNS update to import ▶ "上書き"/"追加" (overwrite/ information. add) ▶ "OK" NOTE ■■Copying Google account contacts If the same contact (same name, reading, etc.) is to your docomo account registered several times, you can collect (join) the ▶ "docomoアカウントへコピー" (copy to several instances of contact information together docomo account) ▶ tap the Google into one. account to copy ▶ "上書き"/"追加" In the contact edit screen, m ▶ "Join" ▶ tap (overwrite/add) ▶ "OK" the contacts to join Use the following procedure to cancel joining. NOTE In the contact edit screen, m ▶ "Separate" If the designation of a contacts item (phone ▶ "OK" number, etc.) on another FOMA terminal differs with that on your FOMA terminal, the PhoneBookCopy designation may be changed or deleted. The number of characters registerable to a You can use a microSD card to copy contacts contact varies with each FOMA terminal. Some data between your and another FOMA characters may be deleted during copying to terminal. You can also copy Contacts data another terminal. registered in a Google account to a docomo If exporting contacts to microSD card, you account. cannot copy data that does not have a name registered.
75 NOTE Voice Mail service If importing contacts from microSD card, files If you are in a location with no radio created with "Bulk backup" cannot be read. reception, the FOMA terminal is powered off, or you are unable to take the phone Available Network Services call, the Voice Mail service answers a call with a Voice Mail greeting and records the You can use the following DOCOMO caller's message. network services on the FOMA terminal. Up to twenty 3-minute messages can be Monthly recorded, and are storable for up to 72 hours. Service name Application charge Calls you are unable to answer after starting Calling/Network Services Voice Mail service Required Paid the Voice Mail service are recorded as "Missed call" to "Call log", and appears in the Call Waiting service Required Paid status bar. Call Forwarding service Required Free (indicating the number of messages) Caller ID notification Not Free appears in the status bar when a message is service required recorded. Public mode (power Not Free The FOMA terminal does not support video off) required voicemail for video phone calls. Make a call to You cannot use the network services when 1412 and disable the video phone support you are outside of the service area or in a setting. location with no radio reception. ■■Basic flow of Voice Mail service "Deactivate" does not result in a Activate the Voice Mail service cancelation of subscription to Voice Mail service, Call Forwarding service, or any ➡ other service. The FOMA terminal receives a call For subscriptions and inquiries, contact ➡ "General Inquiries" provided on the last page of this manual. The call is connected to the Voice Mail In this manual, the outlines of each service center if not answered network service are described with menu ➡ operations of the FOMA terminal. For details, see "Mobile Phone User's Guide [Network Services]". 76 The caller records a message Play messages······Connects to Voice Mail service center. Follow the audio guidance to If you are in a hurry and wish to record a play back recorded messages. message immediately without listening to the Setting······Connects to Voice Mail service answering message, enter "#" to interrupt the center. Follow the audio guidance to change answering message and switch to recording the Voice Mail service settings. mode. ➡ Check messages······Check whether there are new Voice Mail messages. You are notified that there is a message at the Voice Mail service center Message notification······Set whether to notify when there is a new message. ➡ Calling/Network Services Notice call······If there is a call while power Play back the message is OFF or during , an SMS message notifies you once you turn power ON or Using the Voice Mail service enter service range. Notify all calls with "All calls", and only calls m 1 From the Home screen, ▶ that notify their number with "Calls with "Setting" ▶ "Call settings" ▶ caller ID". "Network service" ▶ "Voice mail service" NOTE Select any item: After operating "Setting" or "Check messages" 2 or a Voice Mail message is recorded, an SMS Activate······Makes the Voice Mail service message "NTT DOCOMO:VM:XX" is received. activated. You can also set the ring time. Set ring time······Set time to wait before Call Waiting service connecting to the Voice Mail service. If the ring time is set to 0 seconds, calls are When there is a second incoming call while not recorded to the call log, and are instead you are in call, this service notifies you with connected to the Voice Mail service center a ringtone so you can place the first call on directly. hold to answer. You can also put your current call on hold and place a call to Deactivate······Makes the Voice Mail service another party. deactivated. Check setting······Check current settings. 77 Setting the Call Waiting service ■■Declining an incoming call ▶ Drag on the left of "Decline" to the 1 From the Home screen, m ▶ right. "Setting" ▶ "Call settings" ▶ When the call is finished, " " "Network service" ▶ "Call 2 • Calling with the second caller ends, and waiting" switches to the first caller. Select any item: ■■Placing a call on hold to switch 2 calling Activate······Makes the Call Waiting service ▶ "Swap" activated. • Tap "Swap" to toggle calls with other Calling/Network Services Deactivate······Makes the Call Waiting parties. service deactivated. Putting a call on hold and making a call Check setting······Check current settings. to another party NOTE 1 During a call, " " Even when on hold, a caller is charged a call fee. Enter the other party's phone Putting a call on hold and answering an 2 number ▶ " " incoming call • Put the first caller on hold, and calling switches to the second caller. 1 If you hear a beep during a call, drag on the left of "Answer 3 When the call is finished, " " and Hold" to the right • Calling with the new second caller ends, • Put the first call on hold and answer the and switches to the first caller. incoming call. Call Forwarding service ■■Ending a call and answering an The Call Forwarding service forwards a call incoming call to a preset forwarding number if you do not ▶ Drag on the left of "Answer and answer the call within the preset ring time, End" to the right. or if the FOMA terminal is outside of the • End the first call and answer the service area or is powered off. incoming call.
78 If you do not answer an incoming call after Select any item: the Call Forwarding service is set to "Active", 2 Activate······Set the number of the the call is stored as a missed call in the log, forwarding destination and the ring time and appears in the status bar. and then start the service. ■■Basic flow of Call Forwarding If the ring time is set to 0 seconds, calls are Register the forwarding number not recorded to the call log, and are instead forwarded directly. ➡ Deactivate······Makes the Call Forwarding Activate the Call Forwarding service service deactivated. ➡
Change forwarding No······Change the Calling/Network Services Your FOMA terminal receives a call number of the forwarding destination. ➡ Fwd number busy*······Set whether to connect the caller to the Voice Mail service The call is automatically forwarded to the center when the forwarding destination is specified forwarding number busy. ■■Call Forwarding service fees Check setting······Check current settings. Call Forwarding Forwarding * A subscription to the Voice Mail service is Caller ➡ ➡ required. service subscriber destination Charged to Call Setting forwarding guidance Charged to Forwarding service caller. Set audio guidance to inform a caller when subscriber. their call is being forwarded. Dial "1429" Using the Call Forwarding service 1 • Follow audio guidance to configure From the Home screen, m ▶ settings. 1 "Setting" ▶ "Call settings" ▶ "Network service" ▶ "Call forwarding"
79 Caller ID notification service Public mode (power off) When making a call, you can display your Public mode (power off) is an automatic phone number on the other party's phone. response service dedicated to etiquette Your phone number is important information. required in highly public locations. When Use caution when notifying your number. Public mode is enabled and the FOMA From the Home screen, m ▶ terminal is powered off, a message is played 1 to callers, telling that you cannot answer "Setting" ▶ "Call settings" ▶ the call because you are in a situation where "Network service" ▶ "Caller ID you have to power off the phone (e.g., you notification" are in a hospital or airplane, or close to a Calling/Network Services priority seat in a train), and the call is 2 Select any item: automatically terminated. Setting······Set whether to notify your The Voice mail service* and Call forwarding number. service* take precedence over Public mode Check setting······Check current settings. (power off). * When the ring time is not set to 0 second, the services operate after the Public mode (power NOTE off) message to incoming calls. This function is only active when the other Dial " 25251" party's phone can display the caller ID. 1 • Public mode (power off) is set (without If you hear an announcement requesting caller any indication on the Home screen). ID, activate Caller ID notification or add the "186" prefix to the phone number and call ■■Disabling Public mode (power off) again. Dial " 25250" ■■Confirming the Public mode (power off) setting Dial " 25259"
80 Once Public mode (power off) is enabled The FOMA terminal keeps in Public mode (power off) until you disable it. Simply powering it on does not disable Public mode. The Public mode (power off) message is also provided if the FOMA terminal is powered off or is outside of the service area. A message plays notifying callers that you are where you have to power off the phone and cannot answer, and the phone automatically Calling/Network Services hangs up.
81 Settings
Wireless & Networks Mobile networks Data enabled······Toggle data Configure settings for Airplane mode, communications on/off. Wi-Fi, Bluetooth function, etc. Data roaming → P. 140 1 From the Home screen, m ▶ Access Point Names → PP. 46, 140 "Setting" ▶ "Wireless & Network Mode → P. 140 networks" Network operators → P. 140 2 Select any item: PC Link······Set PC Link on/off. → P. 117
Settings Airplane mode → P. 83 PC Link settings Wi-Fi······Turns on/off Wi-Fi. PC Link······Set PC Link on/off. Wi-Fi settings → P. 48 USB PC Link······Set USB PC Link on/off. Bluetooth······Turns on/off Bluetooth. → P. 118 → P. 84 Destination URL······Display connection Bluetooth settings URL. Bluetooth······Turns on/off Bluetooth. Change Hostname······Set the host name used for the connection URL. Device name······When Bluetooth communication is performed, change Initialize User Name/Password······ the name displayed on a partner's Initialize user name and password. device. Discoverable······Allow the FOMA terminal to be detectable by another Bluetooth device. Scan for devices······Search for Bluetooth devices. Wi-Fi hotspot → P. 86 VPN settings → P. 87 82 Setting to Airplane mode NOTE When Airplane mode is set, all wireless Packet communication is still available when Wi-Fi is turned on. However, if the FOMA terminal is functions of the FOMA terminal (phone calls, connected to a Wi-Fi network, the Wi-Fi network packet communication, etc.) are disabled. takes precedence. When the Wi-Fi network is From the Home screen, m ▶ disconnected, the FOMA terminal automatically 1 "Setting" ▶ "Wireless & connects to the 3G/GPRS network. If you continue using the FOMA terminal connected to the 3G/ networks" ▶ mark the "Airplane GPRS network, note that you will incur costly mode" checkbox packet communication charges. NOTE Using other Wi-Fi network functions Checking "Airplane mode" also turns off the Wi-Fi and Bluetooth functions, but they can be Please turn on Wi-Fi beforehand. turned on again in Airplane mode. Do not use From the Home screen, m ▶ Settings Wi-Fi or Bluetooth in the areas such as hospitals, 1 airplanes, priority seat on the train where the use "Setting" ▶ "Wireless & of radio waves is prohibited. networks" ▶ "Wi-Fi settings" m ▶ select any item: Wi-Fi settings 2 Scan······A scan of Wi-Fi networks starts, From the Home screen, m ▶ and a list of available Wi-Fi networks is 1 "Setting" ▶ "Wireless & displayed. networks" ▶ "Wi-Fi settings" Change priority······Change the priority of Wi-Fi networks to be used. Touch and hold Select any item: 2 the name of a network you want to change Wi-Fi······Turns on/off Wi-Fi. to switch its priority. Network notification······Set whether to notify when an open Wi-Fi network is detected. Wi-Fi Easy Settings → P. 49 Add Wi-Fi network → P. 49
83 Advanced Bluetooth Communication Wi-Fi sleep policy······Configure sleep Connect the FOMA terminal and a Bluetooth- settings for Wi-Fi. compatible device via Bluetooth Set Wi-Fi to enter sleep if no keys are communication. You can connect a Wireless pressed for 15 minutes after the screen Earphone Set 02 (option), etc. to the FOMA dims. After entering sleep, Wi-Fi terminal, and talk on the phone or listen to connection will be closed, but it will music while the FOMA terminal is still in your connect to an access point automatically bag. once a screen lights. There is no guarantee that the FOMA terminal You can also set the Wi-Fi function not is capable of wireless communication with all to enter sleep either at any time or types of Bluetooth devices. during charging. For information about the settings and MAC address······A MAC address is operation procedures, see also the instruction
Settings displayed. manual of the Bluetooth-compatible device. IP address······The IP address currently Precautions when using Bluetooth devices used is displayed. Note the following in order to ensure a Use static IP······Set whether to specify good connection. static IP address for connecting with a • Connect with another Bluetooth device Wi-Fi network. If checkmarked, "IP within about a 10-meter viewable address", "Gateway", "Netmask", distance. Depending on surroundings "DNS 1", and "DNS 2" can be set. To (walls, furniture, etc.) and building use a static IP address, "IP address", structure, the connectable distance is "Gateway", "Netmask", and "DNS 1" shorter. The connectable distance will need to be set. also be shorter if an obstacle is between IP address······Set an IP address. the FOMA terminal and another Gateway······Set a gateway. Bluetooth device. Connection may be Netmask······Set a net mask. unestablishable if your FOMA terminal and the device are located on opposite DNS 1······Set DNS 1. sides of walls containing metal rods, such DNS 2······Set DNS 2. as on upper and lower storeys or in adjoining rooms, especially in a building made of reinforced concrete.
84 Also note that the above connection Bluetooth devices and wireless LAN (IEEE distances are not guaranteed. 802.11 b/g/n) use the same frequency • Connect the FOMA terminal distanced band (2.4 GHz). If you use the FOMA from other devices (electric products/AV terminal or Bluetooth device near a equipment/OA equipment, etc.) as much device equipped with a wireless LAN, as possible (since the terminal is easily radio wave interference may occur and affected by a microwave oven in use, can result in decreased communication distance the terminal as far as possible). speed, noise, a poor connection, etc. If If the terminal is brought closer when this happens, do the following. another device is on, it may be unable to • Keep the FOMA terminal and a Bluetooth connect normally or may be a cause of device in wireless connection at least television and radio noise or interference 10 m from a wireless LAN. (television picture may be unclear for • Turn off a wireless LAN when used within particular UHF or satellite channels). 10 m. Settings • If you cannot connect normally due to a The radio waves emitted by a Bluetooth nearby broadcasting station, wireless device may affect operation of medical transmitter, etc. change the location of electronics or other equipment. Since it the partner Bluetooth device. You may may be the cause of an accident not be able to connect normally if depending on circumstances, turn off the surrounding radio waves are too strong. FOMA terminal and any nearby Bluetooth • You can establish a wireless connection devices in the following places. while a Bluetooth device is in a bag or • Trains pocket. However, if you body is located • Airplanes between the Bluetooth device and the • Hospitals FOMA terminal, decreased • Locations near automatic doors and communication speed or noise may emergency alert devices occur. • Places with ignitable gas, such as gas stations
85 Connecting to a Bluetooth device ■■Canceling the Bluetooth device connection To connect the FOMA terminal with another ▶ Tap the Bluetooth device to disconnect Bluetooth device and exchange data, first ▶ "OK" carry out pairing (connection setting) with • To cancel pairing, touch and hold the the other Bluetooth device and then connect. Bluetooth device you want to disconnect, Some Bluetooth devices only pair, and some and tap "Disconnect" or "Disconnect & Bluetooth devices proceed all the way to unpair". connection. Turn on the partner's Bluetooth function and NOTE check that it is connectable beforehand. When not using the Bluetooth function, turn off From the Home screen, m ▶ the Bluetooth function to prevent battery 1 consumption. "Setting" ▶ "Wireless & If the Bluetooth device is not SCMS-T-compliant,
Settings networks" ▶ "Bluetooth sound cannot be heard regardless of the audio settings" data type. Mark the "Bluetooth" checkbox 2 Using the FOMA terminal as a Wi-Fi ▶ "Scan for devices" access point • A scan for devices starts and a list of available Bluetooth devices is displayed. You can use a tethering function via Wi-Fi • To let your FOMA terminal be connection. By using the FOMA terminal as recognizable by the partner Bluetooth a Wi-Fi access point (main device), you can device, tap "Discoverable". connect to the Internet with a Wi-Fi-compatible device (sub-device), or 3 Tap the Bluetooth device you enjoy services such as online gaming. want to communicate with This function is available only in Japan. • Connection may be established with this From the Home screen, m ▶ procedure, depending on the Bluetooth 1 device. "Setting" ▶ "Wireless & networks" ▶ "Wi-Fi hotspot" ▶ "Pair" or enter the passcode (PIN) "Wi-Fi hotspot settings" 4 ▶ "OK"
86 2 "Configure Wi-Fi hotspot" ▶ Set Connecting to a VPN (Virtual "Network SSID", "Security", and Private Network) "Password" ▶ "Save" A VPN (Virtual Private Network) is ■■Setting a communication channel technology allowing connection externally ▶ "Advanced settings" ▶ "Channel to information on a protected local network Selection" ▶ tap a communication channel such as in a corporation or university. When ▶ "Save" configuring VPN connection from your FOMA terminal, obtain security information 3 Mark the "Wi-Fi hotspot" from the network administrator. checkbox ▶ Check the usage A VPN (PPTP) is unavailable if the access point precautions ▶ "OK" is set to sp-mode. 4 Configure the Wi-Fi-compatible Adding a VPN device (sub-device) with the Settings m same network SSID and security 1 From the Home screen, ▶ as your FOMA terminal "Setting" ▶ "Wireless & • The Wi-Fi-compatible device (sub-device) networks" ▶ "VPN settings" and your FOMA terminal (main device) "Add VPN" ▶ tap the VPN type connect. 2 you want to add NOTE Follow the administrator's When using the FOMA terminal as a Wi-Fi access 3 point and two or more wireless LAN access instructions to configure each points are nearby using the same channel, the item of the VPN setting FOMA terminal may not be found correctly by m ▶"Save" the Wi-Fi-compatible device (sub-device). If not 4 able to be found, change the communication channel. You can connect up to five Wi-Fi-compatible Connecting to a VPN devices at the same time. From the Home screen, m ▶ "Security" is set to "Open" at time of purchase. 1 Configure as required. "Setting" ▶ "Wireless & networks" ▶ "VPN settings"
87 2 Tap the VPN you want to connect 2 Select any item: to Silent mode······Set the FOMA terminal not Enter the required information to to emit sound, etc. for etiquette when in a 3 public or similar place. connect ▶ "Connect" • Alternatively, press the power key for 1 second or longer, and then tap "Silent Disconnecting from a VPN mode". 1 Open the Notifications panel and Vibrator······Set vibration for incoming calls. tap the notification for the VPN Volume······Set the volume for ringtones, connection ▶ tap the connected media playback sound, alarm sound, etc. VPN Phone ringtone······Set the ringtone. Notification ringtone······Set sound for Settings Call Settings email and other notifications. Configure settings for network services, Audible touch tones······Set dial pad operation sound on/off when entering a international dialing assistance , etc. phone number, etc. From the Home screen, m ▶ 1 Audible selection······Set operation sound "Setting" ▶ "Call settings" on/off when selecting from a menu. Select any item: Screen lock sounds······Set operation 2 sound on/off when locking/unlocking the Network service → P. 76 screen. Int'l dial assistance → P. 141 Haptic feedback······Set vibration on/off for specific screen operations. Sound This allows you to configure various Display sound settings, such as Silent mode and Set brightness and other screen settings. ringtones. From the Home screen, m ▶ From the Home screen, m ▶ 1 "Setting" ▶ "Display" 1 "Setting" ▶ "Sound"
88 2 Select any item: 2 Select any item: Brightness······Adjust the brightness of the eco mode······Set eco mode. By setting display. Mark the "Automatic brightness" "Auto", eco mode turns on automatically checkbox to detect surrounding brightness according to battery level set with "Auto and adjust automatically. setting". Auto-rotate screen······Set whether the eco mode option settings······Set the display switches automatically according to action when entering eco mode. the orientation of the FOMA terminal. Brightness······Dims the display. Animation······Set the animation to display Screen timeout······Set the time until when the screen switches. the screen back light turns off. Screen timeout······Set the time until the Turn off Bluetooth······Set the screen back light turns off. About five Bluetooth function off.
seconds after the backlight turns off, you Settings can tap m, h, or r to turn it on Turn off Wi-Fi······Set the Wi-Fi again. function off. Unuse GPS satellites······Set the GPS function off. NOTE Stop sync······Stop application When the battery level becomes low, synchronization. "Brightness" automatically sets to its minimum to conserve power. Stop live wallpapers······Sets a still image as wallpaper when live wallpaper is set. eco mode Auto setting······Set the battery level at You can set eco mode to reduce power which eco mode turns on automatically, consumption. when eco mode is set to "Auto". From the Home screen, m ▶ 1 "Setting" ▶ "eco mode" Location & Security Configure settings such as for security lock and obtaining location information.
89 From the Home screen, m ▶ Clear storage······Delete all credentials 1 "Setting" ▶ "Location & security" information and reset the credentials information storage password. 2 Select any item: Use wireless networks → P. 124 Security codes used with the FOMA Use GPS satellites → P. 124 terminal Set up (Change) unlock Some features of your FOMA terminal security······Configure unlock security codes require security codes, to make various for unlocking the screen, Osaifu-Keitai, etc. functions more convenient. These include a You can set a pattern, PIN (security code), or password for locking the FOMA terminal password. and a network security code for network Screen lock security······Configure to enter services. By using different codes for an unlock security code for unlocking the different purposes, you can get the most Settings screen. out of your terminal. Set up Osaifu-Keitai lock → P. 132 Precautions for all security codes PIN setting → P. 91 Avoid setting security codes using your birthday, part of your phone number, your Visible passwords······Set to display address or room number, "1111" or characters when entering a password. "1234" that can be easily guessed by Select device administrators······Enable/ others. Be sure to write down the security disable administrators for the FOMA codes and store them in a safe location. terminal. Do not reveal your security codes to Use secure credentials······Permit access to others. DOCOMO is not responsible for safe certificates and other credentials damage caused by misuse of your information. revealed security codes by others. • A credentials information storage If you forget your security codes, you password must be set beforehand. need to bring your identification Install from SD card······Install an encrypted document (driver's license, etc.), the certificate from a microSD card. FOMA terminal and the UIM to a docomo Set password······Set a password for Shop Service Counter. For details, contact credentials information storage. "General Inquiries" provided on the last page of this manual. 90 Your PIN unblocking key is written in the PIN1 code is a 4- to 8-digit number (code) application form (copy for subscriber) that is entered to confirm the user when the given at the time of contract. If you have UIM is inserted in the FOMA terminal or the subscribed at a place other than a terminal power is turned on. It is intended docomo Shop, bring your identification to prevent unauthorized use by a third party. Entering PIN1 code makes the FOMA document (driver's license, etc.) and the terminal operable. UIM to a docomo Shop Service Counter, PIN2 code is a 4- to 8-digit number required or contact "General Inquiries" provided when using the user certificate, such as on the last page of this manual. when requesting issue. This FOMA terminal does not support PIN2 Network security code code. The network security code is a 4-digit If you want to use a UIM that has been used on a different FOMA terminal, use the same number necessary for using the docomo Settings Network Services or identification at PIN1/PIN2 code that had been set on the reception of your request in docomo Shop different terminal. The code is "0000" if the or at docomo Information Center. It can be default setting has not been changed. set any number at the subscription and also If you enter the incorrect PIN1/PIN2 code 3 changed later by yourself. times in succession, the PIN1/PIN2 code is You can change your network security code locked. Unlock using "PUK code". to the new one from your PC if you have a Enabling the UIM's PIN "docomo ID/Password" for General support site for PC "My docomo". Set to require entry of the PIN1 code when For information about "My docomo", see the power is turned on. inside of the back cover of this manual. 1 From the Home screen, m ▶ PIN1 code / PIN2 code "Settings" ▶ "Location & security" ▶ "PIN setting" The UIM has two settable security codes, PIN1 code and PIN2 code. These codes are "PIN1 code entry set" set to "0000" (four zeroes) at the time of 2 subscription, but you may subsequently change it. → P.89
91 ■■To change the PIN1 code Applications ▶ "Change SIM PIN" ▶ enter the current PIN1 code ▶ "OK" ▶ enter the new PIN1 This allows you to configure application code ▶ "OK" ▶ enter the new PIN1 code management settings. again ▶ "OK" m • "PIN1 code entry set" must be enabled 1 From the Home screen, ▶ beforehand. "Setting" ▶ "Applications" 3 Enter the PIN1 code ▶ "OK" 2 Select any item: Unknown sources······Set whether to allow installation of applications obtained from PIN unblocking key (PUK) non-Android Market sites, email, etc. The PIN unblocking key (PUK) is an 8-digit Manage applications······You can check number used to unblock the PIN1/PIN2 code. name, version, etc. of applications, or Settings You cannot change the key yourself. force-close/delete/etc. applications. If you enter the incorrect PUK code 10 times Running services······You can display a in succession, the UIM is locked. If this service that is running to stop it, change its happens, please contact a docomo Shop. settings, etc. ■■Unblocking the PUK locked UIM Storage use······Display the state of storage • When the message indicating that a SIM card use for an application. is locked by PUK is displayed, perform the following to unlock. Battery use······Check the amount of "Emergency call" ▶ Enter " 05 [PUK battery used for each application. code] [new PIN1 code] [new PIN1 code]#" Development······Configure various • For example, to change the UIM PIN1 code to settings required for application "2580" when the PIN unblocking key is development. "88888888", enter " 05 88888888 2580 2580#"
92 Accounts & Sync Tap the account you want to 2 synchronize You can configure accounts for online ■■Deleting an account services such as Twitter, Facebook, Google, ▶ Tap the account you want to delete ▶ mixi, Microsoft® Exchange ActiveSync®, to "Remove account" ▶ "Remove account" synchronize data as well as exchange data between the FOMA terminal and servers for 3 m ▶ "Sync now" the various services. If set to synchronize • To stop synchronization, tap m and automatically, the FOMA terminal is then tap "Cancel sync". automatically updated with update NOTE information via the web.
94 From the Home screen, m ▶ Block offensive words······Configure 1 "Setting" ▶ "Language & display of inappropriate results of voice recognition. keyboard" Text-to-speech settings Select any item: 2 Listen to an example······Plays a Select language······Change the language synthesized voice sample. used on the FOMA terminal. Always use my settings······Configure User dictionary······You can add any words application settings to operate to the dictionary, which are displayed as according to "Default Engine", "Install conversion candidates when entering text in voice data", "Speech rate", and the Android keyboard. "Language" settings. Android keyboard······Configure settings Default Engine······Configure the voice such as operation sound when using the synthesizer engine settings for text Settings Android keyboard and display of candidates reading out. for text entry. Install voice data······Install entities ATOK → P. 67 required for the voice synthesizer to run. Speech rate······Configure the text Voice Input & Output reading out speed. Language······Configure the language You can features such as voice search and for text reading out. the text-to-voice conversion function. Pico TTS······Configure the installed From the Home screen, m ▶ voice synthesis engine. 1 "Setting" ▶ "Voice input & output" 2 Select any item: Voice recognizer settings Language······Configure the language settings for voice recognition. SafeSearch······Configure search result filtering.
95 Accessibility Select time zone······Configure the time zone manually. Configure user-aide applications which Set time······Set the time manually. react with sound or vibration when Use 24-hour format······Set the clock to operated. 12-hour display or 24-hour display. Accessibility applications are not registered Select date format······Set the date display at time of purchase. You must download format. and install compatible applications beforehand from Android Market or other sites before you can set "Accessibility". About Phone 1 From the Home screen, m ▶ You can check your FOMA terminal's "Setting" ▶ "Accessibility" state, update software, or upgrade the
Settings Select any item: OS. 2 From the Home screen, m ▶ Accessibility······Set the accessibility 1 functions on/off. "Setting" ▶ "About phone" Power key ends call······Set to end a call 2 Select any item: by pressing the power key. However, in Software Update → P. 151 sleep mode, this does not end a call, and instead cancels sleep mode. Major updates → P. 158 MEDIAS NAVI······Set to receive update Date & Time notifications from MEDIAS NAVI. Status······Check battery level, your phone You can set the FOMA terminal's clock. number, etc. From the Home screen, m ▶ Battery use······Check the amount of 1 "Setting" ▶ "Date & time" battery used for each application. Legal information······Check the open Select any item: 2 source license and Google usage Automatic······Set the time to be adjusted agreement. automatically. Model number······Check your FOMA Set date······Set the date manually. terminal's model number.
96 Firmware version······Check the firmware version. Baseband version······Check the baseband version. Kernel version······Check the kernel version. Build number······Check the build number. Settings
97 Email/Browser
Email Creating and sending email By setting an email account provided by 1 From the inbox screen, m ▶ mopera U or any general service "Compose" providers on your FOMA terminal, you Enter the partner email address can send and receive emails in the same 2 way as your PC. in "To" "Setting an Email account"→ P.50 ■■Adding a Cc or Bcc ▶ m ▶ "Add Cc/Bcc" Displaying email 3 Enter a title in "Subject" 1 From the application list screen, "Email" Enter a message in "Compose Email/Browser • The inbox screen appears. 4 Mail" ■■Refreshing the Inbox ■■Adding an attachment ▶ m ▶ "Refresh" ▶ m ▶ "Add attachment" ▶ tap the • The FOMA terminal receives any new type of attachment ▶ tap the attachment email, and displays it in the "Inbox". "Send" 2 Tap the email you want to read 5 ■■Replying to email ▶ "Reply"/"Reply all" ▶ enter a message Opening mailboxes ▶ "Send" m ■■Forwarding email 1 From the inbox screen, ▶ m ▶ "Forward" ▶ enter the forwarding "Folders" email address in "To" ▶ "Send" • The Inbox, Outbox, etc. are displayed. ■■ Deleting email ■■Importing/exporting email from/to ▶ "Delete" a microSD card ▶ m ▶ "Import/Export" ▶ "Import from SD card"/"Export to SD card" 98 Changing email settings sp-mode Mail 1 From the inbox screen, m ▶ This allows you to send and receive emails "Account settings" using an i-mode mail address (@docomo. ■■Switching email accounts ne.jp). It allows you to use smileys and • You can switch email accounts when two Deco-mail, and also supports auto or more accounts are configured. receive. ▶ "Accounts" ▶ tap the email account to For more information on sp-mode mail, switch to refer to "ご利用ガイドブック (spモード＜ス マートフォン＞編) " (Mobile Phone User's Tap the item to set 2 Guide [sp-mode], in Japanese only). ■■Setting a notification for new email From the application list screen, ▶ Select any item: 1 "spモードメール" (sp-mode mail) Email notifications······Set whether a notification appears in the status bar for new email. Gmail Email/Browser Select ringtone······Set a ringtone for Gmail is an email service provided by notifying new email. Google. You can use Gmail to send and Vibrate······Set vibration for when there is receive email with your FOMA terminal. notification of new email. You must configure a Google account to use Gmail. → P.50 ■■Setting automatic check of new email Viewing an email • You can set the FOMA terminal to check automatically if new email has arrived at 1 From the application list screen, the server. "Gmail" ▶ "Inbox check frequency" ▶ "Never" or • The message thread list screen appears. set the interval to automatically check at • If you set to connect to the server at a certain interval, and if you are using a pay-as-you-go plan, you will incur a charge whenever the FOMA terminal checks for new email. 99 • In Gmail, email is displayed grouped into ■■Forwarding email a message thread according to reply. If ▶ " " ▶ "Forward" ▶ enter the newly arrived emails are replies to an forwarding email address in "To" ▶ m existing email, they will be grouped into ▶ "Send" the same message thread. A new thread ■■Deleting email is created for newly created email and ▶ "Delete" changes of subject name. ■■Switching accounts Creating and sending email ▶ m ▶ "Accounts" ▶ tap the account you want to display From the message thread list 1 m ■■Refreshing Gmail screen, ▶ "Compose" ▶ m ▶ "Refresh" Enter the partner email address • Synchronize the Gmail on your FOMA 2 in "To" terminal and on the website, and refresh the Inbox. ■■Adding a Cc and Bcc ▶ m ▶ "Add Cc/Bcc" ■■Searching email Email/Browser ▶ m ▶ "Search" ▶ enter a keyword in Enter a title in "Subject" the search box ▶ " " 3 2 Tap a message thread Enter a message in "Compose • When there are two or more emails, tap 4 Mail" "X read messages" to display a list of messages. You can tap the message you ■■Adding an attachment want to read and check it. ▶ m ▶ "Attach" ▶ tap the attachment • You can tap to add, check, etc. type ▶ tap the attachment contacts. m ▶ "Send" ■■Replying to email 5 ▶ " " ▶ enter a message ▶ m ▶ "Send" Managing message threads • To reply to all members, tap " " and tap "Reply all". From the message thread list 1 screen, touch and hold a thread
100 2 Select any item: Display message threads by label Read······Open a message thread. You can display only the message threads Archive······Archive (store) message threads. for which "Change labels" is set. Archived message threads are not displayed From the message thread list in the Inbox. 1 screen, m ▶ "Go to labels" Mute······Hide message threads. Tap the type of label you want to Mark unread/Mark read······Designate a 2 display message thread as unread/read. • You can also configure settings to only Delete······Delete a message thread. show message threads with a star (★), Add star/Remove star······Assign/remove a sent email, etc. star from a message thread. Change labels······Add/change the label of Changing Gmail settings a message thread. From the message thread list Report spam······The message thread is 1 screen, m ▶ "More" ▶ deleted and is reported to Google as spam. "Settings" Email/Browser Help······The Google mobile help page is displayed. 2 Tap the item to set ■■Setting a notification for new email ■■Showing archived or muted ▶ Select any item: message threads. From the message thread list screen, m Email notifications······Set whether a ▶ "Go to labels" ▶ "All Mail" notification appears in the status bar for new email. NOTE Select ringtone······Set a ringtone for Labels cannot be created on your FOMA notifying new email. terminal. Create labels on the Gmail website. Vibrate······Set vibration for when there is notification of new email. Notify once······Set whether to notify new email all at once.
101 SMS NOTE While entering a message, m ▶ You can use You can send and receive text messages "Insert smiley" to insert smileys that will be with a cell phone number as the address. displayable on any terminal with Android installed. They are displayed as emoticons while being 1 From the application list screen, entered, but are displayed as smileys once received "Messaging" by an Android terminal. • The message screen appears. You can also send/receive SMS messages to/from ■■Creating and sending SMS users of overseas network operators other than DOCOMO. For available countries/compatible ▶ "New message" ▶ enter the number in overseas network operators, see "Mobile Phone "To", and the message in "Type to User's Guide [International Services]" or the compose" ▶ "Send" DOCOMO "International Services website". ■■Displaying sent/received SMS To send SMS messages to users of overseas ▶ Tap a message thread network operators other than DOCOMO, enter ■■Replying to SMS "+" → "Country code" → "the recipient mobile phone number". Omit "0" if the recipient phone ▶ Tap the address you want to reply to ▶ Email/Browser number starts with "0". You can also send an enter the message ▶ "Send" SMS message by entering "010", "Country ■■Forwarding SMS code" and "the recipient mobile phone ▶ Tap a message thread ▶ touch and hold number". (To reply to an SMS message sent the SMS you want to forward ▶ "Forward" from overseas, enter "010".) ▶ enter the forwarding phone number in "To" ▶ "Send" Deleting SMS ■ ■Add an SMS phone number to From the application list screen, Contacts 1 ▶ Touch and hold a message thread ▶ "Messaging" "Add to Contacts" ▶ "Create new ■■Deleting one message contact" or tap a contact ▶ Tap a message thread ▶ touch and hold ■■Importing/exporting SMS from/to the SMS you want to delete ▶ "Delete a microSD card message" ▶ "Delete" ▶ m ▶ "Import/Export" ▶ "Import from SD card"/"Export to SD card"
102 ■■Deleting a message thread Select ringtone······Set a ringtone for ▶ Touch and hold the message thread you notifying new SMS. want to delete ▶ "Delete thread" ▶ Vibrate······Set vibration for when there is "Delete" notification of new SMS. • All SMS messages in a message thread are deleted. Google Talk ■■Deleting all message threads ▶ m ▶ "Delete threads" ▶ "Delete" Google Talk is an online instant ■■Setting automatic deletion for SMS messaging service by Google. You can ▶ m ▶ "Settings" ▶ mark the "Delete enjoy online chat (chatting by text) with old messages" checkbox ▶ "Text message a partner who has a Google account. limit" ▶ enter a messages limit for each Google Talk, you must set up your own message thread ▶ "Set" Google account. → P.50 NOTE Getting ready for Google Talk You can protect SMS with the following operations. From the application list screen, Email/Browser From the message screen, tap a thread ▶ touch 1 and hold the SMS you want to protect ▶ "Lock "Talk" message" • The talk screen appears. ■■Adding a chat member. Changing SMS settings ▶ m ▶ "Add friend" ▶ enter the Google account of the member you want to 1 From the message screen, m ▶ add ▶ "Send invitation" "Settings" • An invitation goes to the partner you are inviting. Tap the item to set 2 ■■Accepting an invitation ■■Configuring a notification for new • "Chat invitation" is displayed when you SMS get an invitation. ▶ Select any item: ▶ "Chat invitation" ▶ "Accept" Notifications······Set whether a notification appears in the status bar for new SMS.
103 ■■Changing your online status and Enter a message ▶ "Send" message 2 ■■Ending a chat ▶ Tap your account ▶ " " ▶ select the ▶ m ▶ "End chat" online status you want to set ▶ "Status • To end chat with specific members, touch message" ▶ enter a status message ▶ and hold the chat members' names, and "Done" tap "End chat". ■■Changing Google Talk settings ▶ m ▶ "Settings" Browser • You can configure whether log into Google Talk automatically, display chat You can browse web pages using the member classifications, erase search browser. Your FOMA terminal allows you history, display notification icons, and to browse sites via packet communication configure ringtone/vibration settings. and Wi-Fi. ■■Logging out ▶ m ▶ "Sign out" Launching the browser and displaying a web page NOTE Email/Browser When an invitation is accepted, it is removed From the application list screen, from the list of pending invitations. 1 "Browser" Chatting Address bar In the talk screen, tap a chat 1 member's name ■■Switching chat members ▶ m ▶ "Switch chats" ▶ tap a chat member's name ■■Chatting with two or more partners ▶ m ▶ "Add to chat" ▶ tap chat members' names
104 Tap the address bar ▶ enter an Search text contained in a web page 2 URL or keywords While browsing a web page, • Once you enter an URL or keywords in 1 the address bar, a list of candidates m ▶ "More" ▶ "Find on page" appears. Enter the search text ■■Using voice search 2 ▶ Tap the address bar ▶ " " ▶ clearly speak the search words into the microphone " "/" " 3 • Matching before/after text is displayed. 3 " " or tap the web page you want to display from the list of 4 " " candidates • End the search. NOTE Copying text contained in a web page If latest updates have not been installed in the While browsing a web page, FOMA terminal for Flash Player, web contents 1 may not be displayed. Access Android Market m ▶ "More" ▶ "Select text" Email/Browser (P.120) and check the update information for Drag the text to copy, and then Flash Player. 2 drag to the start position and Operation while viewing a web page to the end position ▶ tap the selected text ■■Scroll • Slide in the direction you want to scroll → NOTE P.45 The copied text can be pasted into other applications, such as a browser search box or ■■Zoom in/out email. Touch and hold the text box to paste to, • Slide two of your fingers apart/together and then tap "Paste". where you want to zoom in/out → P.45 • Double-tap (tap twice) where you want to zoom in, then double-tap again to return to Using bookmarks the original display Bookmarking a web page allows you to ■■Moving to before/after a web page quickly access that web page. • r to return to the previous page, m ▶ "Forward" to go to the next page 105 Adding to bookmarks NOTE While "Most visited" or "History" is displayed, 1 In a web page you want to add, appears to the right of the web page name. You m ▶ "Bookmarks" can tap this icon to add ( is gold)/delete ( is • The bookmark appears as a thumbnail. grey) from bookmarks. "★Add" 2 Pasting a web page to the Home screen (Web page widget) 3 Check/change the bookmark Pasting a captured web page to the Home name ▶ "OK" screen allows you to easily display the pasted web page. By setting an update Displaying web pages added to interval, you can update the pasted web bookmarks page automatically with the most recent information when displaying the page. While browsing a web page, 1 While browsing a web page you m ▶ "Bookmarks" 1
Email/Browser want to paste, m ▶ "More" ▶ ■■Viewing frequently visited web "Share page" ▶ "Web page pages ▶ "Most visited" ▶ tap the web page you widget (docomo Palette UI)" want to view ■■Selecting from bookmarks ■■Displaying web pages from browse Open bookmarks and then touch and hold history the web page you want to paste ▶ "Share ▶ "History" ▶ tap the web page you want link" ▶ "Web page widget (docomo Palette to view UI)" ■■Importing/exporting bookmarks 2 Tap the update interval ▶"OK" from/to microSD card ▶ m ▶ "Import"/"Export" Displaying the pasted web page in the Tap the bookmark you want to browser 2 view Tap the pasted web page ▶ m 1 ▶ "Launch browser"
106 Changing settings ■■Phone number • Tap to make a call. 1 " " ▶ select any item: Update interval······Set the interval for Saving images appearing in web updating to the most recent information. pages Target web page······Select a new web While browsing a web page, page for the pasted web page from 1 touch and hold an image you bookmarks. want to save ▶ "Save image"
Opening a new browser window Checking a saved image You can open up to 8 web pages and switch between them easily. While browsing a web page, 1 m ▶ "More" ▶ "Downloads" 1 While browsing a web page, m ▶ "New window" 2 Tap the list • A new browser window opens, and the set homepage is displayed. Email/Browser ■■Switching between windows Changing browser settings ▶ "Windows" ▶ tap the browser window While browsing a web page, you want to view 1 m ▶ "More" ▶ "Settings" Using links in web pages 2 Tap the items to set You can do the following with links ■■Displaying web pages always appearing in web pages. horizontally ■■URL ▶ Mark the "Landscape-only display" • Tap to open a web page. checkbox • Touch and hold to add an URL to bookmarks, ■■Amount of web page zoom when copy an URL, or display in a new window. double-tapped (tap twice) ■■Email address ▶ "Default zoom" ▶ "Far"/"Medium"/ • Tap to create email. "Close" • Touch and hold to copy an email address.
107 ■■Changing the text size ▶ "Text size" ▶ "Tiny"/"Small"/"Normal"/ "Large"/"Huge" ■■Setting the homepage • Set the page that is displayed when you open a new browser. ▶ "Set home page" ▶ enter the URL of the homepage you want to set ▶ "OK" Email/Browser
108 Multimedia
Camera Since the camera consumes more battery power during shooting, you are advised to ■■Before using the camera turn off the camera as soon as you finish While the camera is built with high-precision shooting. Operating the camera on low technology, there may be cases where you battery may result in a dark or blurry see one or more partially dark or constantly screen. bright points or lines. Note also that, when If image stabilization is set to OFF, moving you shoot in a dark place, the camera may the FOMA terminal during shooting may have more noise such as white lines. result in blurry images. Where practical, it Before shooting, clean the lens with a soft is recommended to set image stabilization cloth. A fingerprint or grease marked on to AUTO when shooting. the lens may put the camera out of focus If the battery is low, you may not be able or result in a blurry photo. to save your photos and videos. After the FOMA terminal is left in a warm Even in Silent mode, the camera makes the place for a long time, the image quality shutter sound for photo shooting and the may degrade. video recording start/end sound. You Multimedia The brightness and color in your photos cannot change the volume of these sounds and videos may differ from those of the or turn them off. actual object. Copyright and portrait rights Avoid leaving the lens exposed to direct Avoid copyright infringements when sunlight for a long time or directly shooting copying or editing photos and videos that the sun or a bright lamp. Doing so may have been shot on the FOMA terminal. You cause malfunction, such as discoloration of should also avoid infringing the portrait shot images. rights of other people by using or modifying When shooting, take care not to have your their portraits without their consent. Note finger or hair or the strap block the lens. that the shooting or recording of stage performances, shows or exhibitions may be prohibited, even for personal use.
109 If your use of the FOMA terminal is • Touch shutter: Allows you to shoot easily by inappropriate and a noticeable public tapping where you want to focus. ②Scene annoyance, you may be subject to ③Auto focus: Configures focus settings such as punishment according to federal or local Closeup, Face detection, etc. legislation (public nuisance ordinances, etc.). ④Size (image size) Please be considerate of the ⑤Other Settings: Configures the settings about privacy of individuals around you light, image quality, image stabilization, self when shooting and sending timer, etc. photos using camera-equipped ⑥Focus frame mobile phones. ⑦Number of remaining shots/Image stabilization/ Location information acquisition status ⑧Photo/video switch Viewing the camera screen ⑨Zoom ⑩Shutter ■■Photos ⑪Brightness ⑤ ⑫ ⑫Gallery: Shot photos can be viewed. ④ ⑪ ③ ⑩
Multimedia ② ⑨ ① ⑧ ⑦ ⑥ ①Camera Mode • Standard: The standard camera mode. • Quick Shot: Shoot rapidly in a short timeframe. To shoot more stunning photos, set the camera mode to "Standard". • Continuous Shot: A mode for shooting from 5 to 100 shots in succession. • High sensitivity: Shoot a subject in dark conditions with blur held down to a minimum.
110 ■■Videos Shooting with the camera ③ ⑨ Photos and videos shot on the camera are ② ⑧ automatically saved to a microSD card. If you do not have a microSD card inserted, you ① ⑦ cannot start shooting. ⑥ Shooting photos ⑤
Before shooting ④ From the application list screen, 1 "Camera" Point the camera at a subject ⑧ 2
⑦ " " ⑥ 3 • The camera shoots a photo with a shutter ⑩ click. During shooting Shooting videos
①Auto focus 1 From the application list screen, Multimedia ②Size (image size) "Video Camera" ③ Other settings: Configures the settings about Point the camera at a subject lighting, image quality, image stabilization, 2 etc. can be made. ④Remaining shooting time/Image stabilization " " ⑤Photo/video switch 3 • Recording starts with a recording start ⑥Zoom sound. ⑦Recording start/end ⑧Brightness " " ⑨Gallery: Shot videos can be played. 4 • Recording ends with a recording end ⑩Shooting time elapsed sound.
111 NOTE NOTE If there is a notification sound during video You cannot "Share" contents protected by shooting, it may also be recorded. Digital Rights Management (DRM) with other terminals. Gallery If you use "Factory data reset", contents protected by Digital Rights Management (DRM) This allows you to show or play photos/ can no longer be played. videos saved to microSD card from a camera, site download, etc. Music Player The following file formats can be played. H.263(3gp,mp4), H.264(3gp,mp4), The Music Player plays music files stored MPEG-4 SP(3gp), WMV(wmv,asf) on a microSD card. Save music files to microSD card from a PC 1 From the application list screen, beforehand.→ P.117 "Gallery" The following music file formats can be • Shot images, downloaded images, etc. played. are displayed in categories. AAC LC/LTP, HE-AACv1 (AAC+), HE-AACv2 Tap a category (enhanced AAC+) (3gp,mp4,m4a), 2 AMR-NB, AMR-WB (3gp), MP3 (mp3), MIDI
Multimedia (mid, xmf, mxmf, imy, rtttl, rtx, ota), Ogg 3 Tap the photo/video you want to Vorbis (ogg), PCM/WAVE (wav), WMA view (wma,asf) • Tap to arrange the photos by "Using an earphone"→ P.35 shooting period. • Touch and hold a category or photo/video Playing music to send data by Bluetooth communication or mail, or to delete data, check details, 1 From the application list screen, etc. "Music" NOTE Tap a category If you have many photos saved, Gallery may take 2 • Tap the "Artists", "Albums", "Songs", or time to read all the photos when it is activated. "Playlists" category. • You can also touch and hold m to enter text and search. 112 Tap an item ④Return to start of song, or skip to previous 3 • If you select the "Songs" category, tap song/Pause/Skip to next song the song you want to play to start ⑤Specify playback position playback. ■■Using party shuffle • Touch and hold an item then tap "Play" ▶ m ▶ "Party shuffle" to play all songs in that item. • Use this to randomly select and play ■■Setting as the ringtone several songs from all the songs. ▶ Touch and hold a song ▶ "Use as phone By setting to party shuffle, changes to ringtone" . Tap a song NOTE 4 If you use "Factory data reset", contents protected by Digital Rights Management (DRM) can no longer be played. ① Using playlists
② Creating a playlist
③ From the application list screen, 1 "Music" Multimedia ④ Touch and hold the artist name, ⑤ 2 album name, or song name ▶ ①Album cover image "Add to playlist" ②Song list display/Shuffle setting/Repeat setting Tap the playlist you want to add • In song list display, you can drag to 3 • When you have selected an artist or change the order of songs. album, all songs under the selected item ③Song details are added to the playlist. • You can touch and hold to search • Tap "Current playlist" to add the song to related information for each a current song list. You can check the application. added song by tapping in the playback screen.
113 ■■Creating a new playlist NOTE ▶ "New" ▶ enter a playlist name ▶ "Save" Playlists cannot be deleted from "Recently • A new playlist is created for adding added". songs. Deleting a song from a playlist Changing the playback order of a playlist From the application list screen, From the application list screen, 1 "Music" ▶ "Playlists" 1 "Music" ▶ "Playlists" Tap a playlist 2 Tap a playlist 2 Touch and hold the song you Drag " " 3 3 • The song order changes where dragged. want to delete ▶ "Remove from playlist" Renaming a playlist From the application list screen, 1 "Music" ▶ "Playlists"
Multimedia Touch and hold the playlist you 2 want to change ▶ "Rename" ▶ enter a playlist name ▶ "Save" NOTE Playlist names cannot be changed in "Recently added".
Deleting a playlist From the application list screen, 1 "Music" ▶ "Playlists" Touch and hold the playlist you 2 want to delete ▶ "Delete" 114 File Management
Infrared Data Exchange
Your FOMA terminal can exchange 15° Contacts and MyProfile information with 15° another FOMA terminal or other terminal that features the infrared data exchange function. Be sure the infrared data ports are aligned Infrared data in parallel. Do not place anything between port the FOMA terminals or block their infrared ports. Within approx. 20 cm If the infrared data port has any dirt on it, wipe it off with a soft cloth so as not to damage the port. Damaging the port may Sending contacts by infrared data cause the infrared data exchange to fail. exchange When using infrared data exchange, make sure that your terminal is not more than 1 From the application list screen, 20 cm away from the other terminal. Do "Contacts" ▶ tap the contact you not move the terminals until a message want to send appears indicating exchange is complete. File Management m Under direct sunlight, fluorescent lighting, 2 ▶ "Share" ▶ "OK" ▶ "IrDA" or near infrared devices, the terminal may • Put the receiving FOMA terminal on not be able to communicate normally standby for reception. because of their effect. "OK" Depending on the other FOMA terminal, 3 • Point the infrared data port to the exchanging contacts may not be possible. receiving terminal. 4 "OK"
115 Receiving contacts by infrared data Sending data by Bluetooth exchange communication
116 Connecting to a PC Open the Notifications panel, "USB 2 Connection" ▶ "USB Mass Storage" ▶ "OK" ▶ "OK" Connecting the FOMA terminal and • You can now use your PC to display files a PC on a microSD card. Connect the FOMA terminal and a PC with the microUSB cable for PC connection Safely removing the microUSB (sample). cable for PC connection When you plug in/unplug the microUSB cable for PC connection from the PC, hold the USB Open the Notifications panel, plug horizontally. → P.43 1 "Turn off USB storage"/ NOTE "Disconnect" ▶ "OK" Connect the USB plug of the microUSB cable for Remove the microUSB cable for PC connection directly to the USB port of the PC. 2 If the cable is connected via a USB hub or USB PC connection (P.43) extension cable, a malfunction may occur. Do not unplug the microUSB cable for PC Using PC Link connection while data is being transferred. The data may be destroyed. You can connect your FOMA terminal and a PC via a Wi-Fi connection, USB PC Link, Using data on a microSD card etc., to access files on your terminal from your PC using dedicated software or a When you connect your FOMA terminal to a dedicated browser. File Management PC or other device by using the microUSB Use dedicated software to do the cable for PC connection (sample), you can following. read and write data on a microSD card from • Transfer PC files to a microSD card in your the PC. FOMA terminal 1 Connect the FOMA terminal to a • Import/export contacts, email, or PC using the microUSB cable for bookmarks from/to your FOMA terminal PC connection • Open a specified web site with your FOMA terminal • Search an application with your FOMA terminal 117 Use a PC browser to do the following. • The host name you enter here is the host • Browse/edit contacts and bookmarks on name you checked in step ②. your FOMA terminal • (User registration request) appears in • Browse the Gallery on your FOMA the Notifications panel on your FOMA terminal terminal. Open the Notifications panel, Using PC Link with dedicated 6 "User registration request" ▶ software check that the user name Install dedicated software on your PC displayed on your FOMA terminal beforehand. Refer to the following site for software download and operating details. is the same as the user name http://www.n-keitai.com/guide/download/ entered on your PC ▶ "Yes" ▶ (in Japanese only) "OK" From the Home screen, m ▶ • You can now access files on your FOMA 1 "Setting" ▶ "Wireless & terminal from your PC. networks" ▶ "PC Link settings" ■■Using PC Link with a browser From the Home screen, m ▶ "Setting" Mark the "PC Link" checkbox ▶ ▶ "Wireless & networks" ▶ "PC Link 2 check the host name ▶ "OK" settings" ▶ check "Destination URL", and • To change the host name, enter a host then enter the displayed URL in browser's name and tap "OK". address bar on your PC
File Management 3 Connect the FOMA terminal to Connecting your FOMA terminal and a your PC PC via USB PC Link • Connecting via Wi-Fi→ P.48 You can now connect your FOMA terminal • Connecting via USB PC Link→ P.118 and a PC using the microUSB cable for PC 4 Launch the dedicated software connection (sample) to use PC Link. on your PC 1 Connect the FOMA terminal to Enter a host name ▶ set the user your PC using the microUSB cable 5 name/password for PC connection • This step is done on your PC.
118 Open the Notifications panel, 2 "USB Connection" ▶ "USB PC Link" ▶ "OK" ■■Removing the microUSB cable for PC connection → P.117 NOTE Only one FOMA terminal can be connected via USB PC Link and recognized per one PC. File Management
119 Applications
Android Market NOTE If you need more information about Android You can use Android Market to directly Market, from the market screen, m ▶ tap access useful applications and enjoyable "Help". games which can be downloaded and installed on your FOMA terminal. Installing applications 1 From the application list screen, Search for an application from "Market" 1 the market screen • The market screen appears. • The first time you launch Android Market, 2 Tap the application you want to terms of service are displayed. After install confirming the terms of service, tap "FREE" "Accept". 3 • Carefully check the displayed content. NOTE By tapping "OK" in this screen, you Check the security of applications before accept responsibility for using the
Applications installing them. Applications are installed at application on your FOMA terminal. Use your own risk. The FOMA terminal may get particular care with applications that infected with a virus and all data on the terminal access a large number of functions or may be damaged. large amounts of data. NTT DOCOMO shall not accept liability for any "OK" malfunctions caused by the applications that you 4 have installed. If a malfunction results, repair will • Application download and install starts. be at cost, even if within the warranty period. You can check progress of the download NTT DOCOMO shall not accept liability for any from the Notifications panel. When disadvantage to you or a third party caused by installation is complete, a notification the applications that you have installed. appears in the Notifications panel. Some applications connect to the Internet and NOTE carry out communication automatically. Note To stop download, open the Notifications panel, that you may incur costly packet transmission tap the application, and then tap "Cancel". charges. 120 Purchasing applications ■■Requesting refund You can request a refund within a stipulated Fee-based applications must be purchased time after purchase. The application will be before download. deleted, and you will not be charged for it. You only make payment once for an You may obtain only one refund for each application. application. If you have previously requested and Once you have downloaded an application, obtained a refund for a purchased application, you do not need to make payment each time you cannot obtain another refund for that same you uninstall or redownload it. application after you purchase it again. From the market screen, search For information on payment methods and 1 for an application refund terms, from the market screen, m ▶ from "Help", see each item for "Buying apps". Tap the application you want to NOTE 2 purchase Customers using sp-mode can also make Tap the monetary amount box payment together with their monthly FOMA 3 • Carefully check the displayed content. terminal fees (Content Payment Service). For By tapping "OK" in this screen, you details, refer to the NTT DOCOMO website. accept responsibility for using the For an initial purchase by credit card, you must application on your FOMA terminal. Use enter information for the credit card you use for Google Checkout. Google Checkout is a fast, particular care with applications that Applications access a large number of functions or secure, and convenient method for purchasing large amounts of data. applications from your FOMA terminal. For more information on Google Checkout, refer to "OK" "http://checkout.google.com/". 4 • Continue by following onscreen Your Google Checkout information will be instructions. stored on your FOMA terminal. Set the screen • Tap the links for the displayed important lock to ensure the security of your FOMA notices including "Refund Policy" and terminal. → P.90 "Google Billing and Privacy Policy" and check their content.
121 Deleting applications NOTE DOCOMO shall not accept liability for any In the market screen, m "My damages caused by sites introduced from 1 apps" docomo market, or by information obtained from such sites. 2 Tap the application you want to DOCOMO shall not accept liability for the delete contents, suitability or reliability of applications "Uninstall" ▶ "OK" introduced from docomo market. Depending on the applications that you install, 3 • For fee-based applications, an "Uninstall the operation of your FOMA terminal may & Refund" screen appears. become unstable and your location or personal Select the reason for deletion ▶ information saved on the FOMA terminal may be 4 "OK" disseminated on the Internet and used improperly. You should therefore thoroughly check the provider and operation status of an docomo market application before using it. The copyright of materials on the docomo The docomo market provides you with market site (documents, photographs, easy access to sites recommended by illustrations, videos, sounds, software, etc.) are DOCOMO and to convenient applications. owned by DOCOMO or other third parties, and
Applications From the application list screen, are protected by the Copyright Act, other laws 1 and agreements. Excluding the extent of "docomo market" quotation and reproduction for private use that NOTE is approved in the Copyright Act, the Packet communication (3G/GPRS) or a Wi-Fi reproduction, adaptation or public transmission Internet connection is required for access to of copyrighted material is prohibited without the docomo market. consent of the party owning the copyright. Separate packet communication charges are incurred when connecting to docomo market and when downloading applications from docomo market. Some applications automatically perform packet communication. There are some paid applications in docomo market.
122 GPS Some wireless communications products (mobile phones, data detectors, etc.) block You can use your FOMA terminal's GPS satellite signals and cause instability of function and compatible software to signal reception. check your present location, find The display of some maps based on directions to a destination, etc. location information (latitude/longitude DOCOMO shall not accept liability for any information) may be inaccurate due to the damage caused by a malfunction of the regulations of some countries or regions. GPS system. You may find it impossible or difficult to DOCOMO shall not accept liability for any receive the GPS signal in the following purely economic damages caused by conditions because GPS uses radio waves missed opportunities to check the from a satellite. measurement (communication) results due • Inside or immediately underneath a to external factors, such as a failure or building malfunction of the FOMA terminal, or a • In a basement or tunnel, underground, or power failure (including the battery underwater running down). • In a bag or box You cannot use the FOMA terminal as a • In a built-up or residential area navigation device for an aircraft, vehicle or • In or under thick trees person. DOCOMO shall therefore not • Near a high-voltage cable Applications accept any liability for damages caused by • Inside cars or trains navigation using the location information. • In heavy rain, snow, or other bad weather You cannot use the FOMA terminal as a • When there are obstructions (people or high-accuracy measurement GPS. objects) near the FOMA terminal DOCOMO shall therefore accept no liability • When the GPS antenna section of the for damages caused by measurement error. FOMA terminal is covered with a hand GPS is operated by the U.S. Department of Defense. GPS signals are subject to control adjustments (reduced accuracy, stoppage of signal, etc.) at the discretion of the Department.
123 Enabling the Location Service Using Google Maps To use the Location Service, you must enable You can use Google Maps display your the GPS function beforehand. You can also current location, search other locations, configure your terminal to find approximate search directions, etc. location information based on information To use Google Maps, a 3G/GPRS or Wi-Fi from Wi-Fi and mobile network base connection enabling data communication is stations. required. Set the Location Service on beforehand. Enabling the GPS function → P.124 Google Maps does not cover all countries and From the Home screen, m ▶ cities. 1 "Setting" ▶ "Location & security" 1 From the application list screen, 2 Mark the "Use GPS satellites" "Maps" checkbox ▶"Agree" • The first time you launch this application, NOTE a screen presenting new map features appears. Tap "OK". By agreeing, Google Location Service gathers location information in a manner not enabling ■■Zooming in/out on the map pinpointing of individuals. Gathering of location • Zoom in :Tap , slide two of your
Applications information occurs regardless of whether an fingers apart, and then application is launched. double-tap (tap twice) • Zoom out :Tap , slide two of your Enabling search of current location by fingers together, and then tap wireless network with your two fingers m ■■Displaying current location From the Home screen, ▶ ▶ " " 1 "Setting" ▶ "Location & security" ■■Searching a location Mark the "Use wireless ▶ "Search Maps" ▶ enter a location to 2 networks" checkbox ▶ "Agree" search ▶ "実行" or tap a search candidate • You can tap a balloon to check details.
124
■■Viewing Street View 4 Tap the means ( (car)/ ▶ Touch and hold a point you want to view (public transport)/ (on foot)) in Street View ▶ tap a balloon ▶ " " • Some regions are not supported for ▶ "Go" Street View. • When several sets of directions are found, ■■Displaying layers tap the desired directions. • You can display information such as " " traffic conditions overlaid on a map, or 5 • The directions are displayed on a map. switch to an aerial photograph. ▶ " " ▶ tap the item you want to view Using Navigation • Traffic conditions and railway lines are provided for limited regions. You can use audio guidance to the destination. ■■Clearing a map • Clear all displayed layers and directions 1 From the application list screen, search results. "Navigation" ▶ " " ▶ "Clear Map" • The first time you launch this application, a description of Google Maps Navigation Looking up directions is displayed. Tap "Accept". You can view directions to your destination. Select any item: m 2 Applications 1 While viewing a map, ▶ Speak Destination······Enter your "Directions" destination by voice. Enter the starting point in the Type Destination······Enter your destination 2 textbox above by text entry. Contacts······Enter your destination from an Enter the arriving point in the address registered in your contacts. 3 textbox below Starred Places······Enter your destination • You can tap and specify a contacts from a location with a star added in Google address, a map location, etc. Maps. • Navigation starts. ■■Exiting navigation ▶ m ▶ "Exit Navigation" 125 NOTE For more information on Latitude, use the If driving a car, be sure someone other than the following to refer to mobile Help. driver operates the navigation. From the Latitude screen, m ▶ "See map" ▶ m ▶ "More" ▶ "Help" ▶ "Latitude" Using Places 1 From the application list screen, You can search for shops and facilities near "Latitude" your current location and display information. Shops and other locations that 1Seg were found can be displayed in the Google Maps screen. 1Seg is a terrestrial digital TV From the application list screen, broadcasting service for mobile devices 1 and enables these devices to receive data "Places" broadcasts in addition to video and audio Tap the facility, etc. you want to broadcasts. It allows users to obtain more 2 find detailed information about TV programs • A list of search results is displayed. and to readily participate in quiz shows and enjoy TV shopping and other 3 Tap the desired facility, etc. contents. • Detailed information is displayed. For details on the 1Seg service, refer to Applications the following website: Using Latitude The Association for Promotion of Digital Google Latitude enables you and your Broadcasting friends to check each others' locations on http://www.dpa.or.jp/english/ maps and share status messages with each other. It also enables you to send email and ■■Notes on the use of 1Seg SMS messages, make calls and search for The 1Seg service is provided by TV directions to friends' locations. broadcasters and other organizations. You will Location information is not shared not be charged for the video and audio automatically. You must first join Latitude and content you receive. For information about then invite friends to provide their locations, the viewing fees charged by NHK, please or accept invitations from friends to share contact the broadcaster. your location.
126 The data broadcast area displays two types of To get good reception, fully extend the antenna information: "Data broadcast" and "Data for the 1Seg service. Changing the orientation broadcast website". of the antenna, or moving to another location A "Data broadcast" is brought by airwaves, may result in better reception. together with video and audio, and a "Data ■■1Seg antenna broadcast website" is displayed by the mobile When changing 1Seg antenna direction, device connecting to a website prepared by a do not apply excessive force. TV broadcaster or other organization. Packet communication charges are incurred for viewing a "Data broadcast website" or other website. Some websites may charge you for the information they provide. ■■Airwaves 1Seg is a broadcasting service that operates on radio waves (airwaves) different from those for the FOMA service. Therefore, you cannot receive the 1Seg service in locations that airwaves cannot reach or during hours when program is not available, regardless of whether you are outside or inside the FOMA service area. Applications Even in areas where the terrestrial digital TV broadcasting service is available, you may have poor or no reception in the following places: NOTE • Place far away from a tower that transmits When stowing the 1Seg antenna, do not hold by airwaves its tip and forcibly stow it. May cause damage. • Place in a mountain area or behind a building Push the antenna straight down its length as far where radio waves are blocked by land or as it will go, then swing it inward to stow. structural features • Inside a tunnel, underground, inner area of a building or other place where radio waves are weak or nonexistent
127 Viewing 1Seg Viewing the 1Seg viewing screen From the application list screen, Change to vertical display to display data broadcast. 1 "TV" • The TV menu screen appears. • The first time you launch 1Seg, you are required to set channels. → P.128 ① 2 "TV" ■■Adjusting the volume ▶ Press the volume key ② ■■Set subtitles and audio ③ ▶ m ▶ "Subtitle/Sound" ①TV picture area Setting channels • Flick left/right to select a channel • Touch and hold to display the channel list 1 From the TV menu screen, "TV" ②Data broadcast area ③Controls m ▶ "Change area" Data broadcast Applications 2 controls
Tap the area Tap the TV picture area to switch the display 3 • By selecting a registered area, the TV switches to the selected area to view 1Seg. "OK" ▶ tap the prefecture or Display program 4 information Tap region for the area Display the channel list • Scan channels and register channel information. 5 "OK" Select channel : Start recording : Cancel recording 128 Using the program guide Playing a recorded program You can browse a program guide for In the TV menu screen, "Playback terrestrial digital TV and BS digital 1 broadcasting. Search for programs by Recorded Program" keyword, genre, etc., and book programs Tap the program you want to for viewing/recording. 2 play In the TV menu screen, "Program • The program plays. 1 guide" • The same as with the 1Seg viewing screen, operate programs with the ■■While viewing 1Seg controls.→ P.128 ▶ While viewing 1Seg, m ▶ "Program guide" • The first time you launch the program guide, a regional setting screen appears. Rewind Fast forward Choosing a program to view : Play : Pause 1 Tap a program you want to view on the program guide ▶ "ワンセ Frame forward/backward while paused ( / )
グ起動" (Launch 1Seg) Applications Using a TV link Booking viewing or recording Depending on the data broadcast, link Book programs for 1Seg viewing or information to related sites (TV links) are recording. An alarm sounds at the time you displayed, and can be added to allow you to set for the start of a program or recording. connect to related sites later. 1 Tap a program on the program To add TV links, tap an item that allows TV guide ▶ "ワンセグ視聴予約" (Book links in the data broadcast area. 1Seg viewing)/"ワンセグ録画予約" In the TV menu screen, "TV Link" (Book 1Seg recording) 1 Check each item ▶ "Save" ▶ Tap a link ▶ "YES" 2 "YES" 2
129 ■■Deleting a TV link Osaifu-Keitai ▶ Touch and hold the TV link you want to delete ▶ "Delete" ▶ "Delete one"/"Delete The Osaifu-Keitai function allows you to all" ▶ "YES" make payments, use coupons, participate in stamp rallies, etc. simply by waving the Configuring 1Seg settings FOMA terminal, equipped with an IC In the TV menu screen, "Settings" card, over the reader in the store. In 1 addition, by waving the FOMA terminal over the reader, you can access websites, 2 Select any item: obtain the latest coupons, receive Data Broadcasting settings electronic money and check the usage status of electronic money by data Confirm connection······Set a communication. Also, you can lock the confirmation message to appear before carrying out communication. Osaifu-Keitai function for security in case you lose the FOMA terminal. Use location info······Set to use For details on Osaifu-Keitai, see "ご利用ガ location information. イドブック (spモード＜スマートフォン＞編)" Use phone info······Set to use FOMA (Mobile Phone User's Guide [sp-mode], in terminal information. Japanese only) and docomo market. Applications Delete station data······Delete stations To use the Osaifu-Keitai service, you need from memory. to make settings on the relevant website Sleep Timer······Set the time until 1Seg or by using the relevant application. automatically ends. A fault in the FOMA terminal may cause Product Information······Display product the data stored in the IC card (including information. electronic money and earned points) to be lost or changed. Before submitting the FOMA terminal for repair, you should in principle delete all data from the terminal by yourself; the FOMA terminal will not be accepted if it contains any data.
130 For information about data reissuance, Make the settings related to the restoration, temporary storage, transfer 3 service and other forms of support, check with • Make necessary settings from the service your Osaifu-Keitai service provider. You are website or application. advised to use an Osaifu-Keitai service with a backup service for important data. Holding the FOMA terminal over a NTT DOCOMO shall not accept liability for reader any damages arising in relation to the You can hold the e up to a reader to Osaifu-Keitai service, including the loss or enable an electronic transaction. change of the IC card data, in any events The notification LED lights (blue) when you are including failures and phone model using Osaifu-Keitai. changes. If you have your FOMA terminal stolen or lost, contact your Osaifu-Keitai service provider immediately for information about necessary action. Using the Osaifu-Keitai To use an Osaifu-Keitai service, download an Applications Osaifu-Keitai application from an Osaifu- Hold the e mark over the reader Keitai website and then make necessary settings. Some Osaifu-Keitai services may not require downloading an Osaifu-Keitai Note the following when holding your FOMA application. terminal up to a reader. • Do not strike your FOMA terminal against 1 From the application list screen, the reader "Osaifu-Keitai" • Hold the e mark evenly with the reader • If initial settings have not been • Hold the e mark at the middle of the completed, the initialization screen reader as much as possible appears. • If unreadable by the reader, move the e Tap the service you want to use mark above/below, to the left/right of the 2 reader • Do not attach anything metal on the side of your FOMA terminal with the e mark 131 Locking Osaifu-Keitai ToruCa Lock Osaifu-Keitai to prevent it from being used by another person without permission. ToruCa is an electronic card that can be The Osaifu-Keitai function is not unlocked imported into the FOMA terminal. even if you turn off the power of the FOMA Available from a reader or online, it terminal. provides shopping information or serves This function is enabled when "Set up as a coupon. The imported ToruCa is (Change) unlock security" is any setting other saved in the "ToruCa" application that than "None". allows you to view, find or update a To set this function/unlock, you must enter ToruCa. the unlock security code you set with "Set up For details on ToruCa, see "ご利用ガイド (Change) unlock security". ブック (spモード＜スマートフォン＞編)" 1 From the application list screen, (Mobile Phone User's Guide [sp-mode], in "Osaifu-Keitai" ▶ m ▶ "おサイ Japanese only) and docomo market. フケータイ ロック設定" From the application list screen, 1 "ToruCa" 2 Select any item: OFF······Unlock Osaifu-Keitai. NOTE Packet communication charges may be incurred Applications ON when you import, view or update a ToruCa. Work with screen lock······Set to lock You may not be able to import, view or update a together with the screen lock. Unlocking ToruCa that has been provided for an i-mode the screen also unlocks Osaifu-Keitai. terminal. Turning ON always ······The lock Depending on the settings by the IP (Information always activates. To cancel locking, set Provider), the following functions may not be "おサイフケータイ ロック設定" to "OFF". available: • Import from a reader • Update • Transmission by email • Transfer or copy to a microSD card • Map display Depending on the IP settings, you may not be able to display a map from a ToruCa list, even if the ToruCa (details) supports map display. 132 NOTE NOTE When the Osaifu-Keitai is locked, a ToruCa Tap to start the "Music" application and play cannot be imported from a reader. music. → P.112 When the duplicate check is set to "ON" you cannot import an identical ToruCa more than Setting the alarm once. To import an identical ToruCa more than once, set the check to "OFF". While the clock is displayed, " " When sending a ToruCa by email, it is sent in its 1 • m ▶ from "Settings", you can set pre-import state. "Alarm in silent mode", "Alarm volume", You may not be able to save a ToruCa that has "Snooze duration", and "Volume key been emailed to you, depending on the email behavior". application that you are using. "Add alarm" Depending on the type of the browser, you may 2 not be able to import a ToruCa via it. When moving or copying a ToruCa to a microSD Set the alarm time ▶ "Set" card, it is moved or copied in its pre-import state. 3 When the initial setup of the Osaifu-Keitai has not been performed, a ToruCa cannot be Select any item: imported from a reader. 4 Turn alarm on······Set the alarm to operate.
Time······Set the alarm time. Applications Clock Repeat······Set the alarm to sound at the From the application list screen, same time on each day. 1 "Clock" Ringtone······Set the alarm sound. • Time and date, day, and the weather Vibrate······Set the terminal to vibrate forecast for the region set in "News & together with the alarm. Weather" are also displayed. Label······Assign a label to the set alarm. NOTE • When the alarm sounds, tap "Dismiss" to Tap to switch the backlight on/off. stop the alarm. By tapping "Snooze", the Tap to view the photos stored on the microSD alarm sounds again according to the card in a slideshow. Tap r to stop the "Snooze duration" setting. slideshow. 5 "Done" 133 Calendar ■■Changing/deleting events ▶ Tap an event you want to change ▶ You can manage your schedule by m ▶ "Edit event"/"Delete event" synchronizing your FOMA terminal calendar with an online calendar Changing calendar settings provided by Google or other service. While viewing the calendar, m • You must configure a Google account 1 ▶ "More" beforehand. → P.50 From the application list screen, 2 "Settings" ▶ change settings as 1 "Calendar" needed • You can set the schedule's notification ■■Switching the calendar display method and ringtone/vibration, and the ▶ m ▶ "Day"/"Week"/"Month" reminder's notification time. Creating a schedule ■■Synchronizing with Google or other Calendar While viewing the calendar, ▶ "Calendars" ▶ tap the account of the 1 touch and hold the day to enter calendar to display, and then set to synchronize/display ▶ "OK" an event in ▶ "New event" Applications 2 Set each item ▶ "Done" Calculator From the application list screen, NOTE 1 appears in the status bar when the set time "Calculator" arrives. You can open the Notifications panel and • Flick to left/right to switch between check the details. Tap "Dismiss all" to clear all functions and +/-/×/÷. notifications, and tap "Snooze all" for the • You can touch and hold the formula box notifications to appear again in 5 minutes. to copy/paste a formula. • Tap "CLEAR" to delete entered digits and Checking the agenda operators, or touch and hold to delete all of a formula. While viewing the calendar, m • You can tap and to display the 1 ▶ "Agenda" formula history.
134 Quickoffice If using iD with an Osaifu-Keitai, you will need to apply to a credit card issuer You can view and edit documents that compatible with iD, as well as make have been saved on a microSD card. The configurations with iD appli. following files are supported. Expenses (annual fees etc.) for using iD • Excel (Excel 97 to Excel 2010): xls, xlsm, services differ by the credit card issuer. xla, xlam, xlt, xltm, xlsx, xltx Overseas usage charges for packet • Word (Word 97 to Word 2010): doc, docx, communication are different from those in docm, dot, dotx, dotm Japan. • PowerPoint (PowerPoint 97 to PowerPoint For more information on iD, see the iD site 2010): ppt, pptx, pot, pptm, ppsm, potx, (http://id-credit.com/) (Japanese). potm, ppsx From the application list screen, • Acrobat (Acrobat 5 to 9)*: pdf 1 "iD設定アプリ (iD appli)" • TEXT*: txt * Uneditable News & Weather 1 From the application list screen, "Quickoffice" From the application list screen, 1 "News & Weather"
iD設定アプリ (iD appli) Applications Changing weather forecast settings "iD" is convenient e-money that uses a credit system. You can shop easily and While news and weather are conveniently by simply waving an Osaifu- 1 displayed, m ▶ "Settings" Keitai or an iD-enabled card with credit card information over the reader unit. 2 "Weather settings" You can register up to two credit cards on an Osaifu-Keitai. This allows you to use Select any item: your credit cards appropriately for 3 giveaways, etc. Use my location······Set the location for Depending on the credit card issuer, you displaying weather forecasts to automatically set to your current location. can withdraw cash.
135 Set location······Enter a city name or postal From the application list screen, code to set a location for displaying weather 1 "Topics" forecasts. Use metric······Toggle metric and Imperial measurements.
NOTE
Days
Applications You can create and view a journal automatically from email, call logs, or SNS exchanges. From the application list screen, 1 "Days"
Topics Automatically gather everything from Twipple trends to the most talked-about topics, as well as you and your friends’ hot topics from SNS services, for easy browsing.
136 Using Overseas
Overview of International Services Available Overseas Roaming (WORLD WING) Communication service 3G GSM/GPRS GSM The WORLD WING international roaming Calling ○ ○ ○ service allows you to use your FOMA SMS ○ ○ ○ terminal in the service areas of overseas Email*1 ○ ○ × operators affiliated with DOCOMO, with *1 Browser ○ ○ × the same phone number and email GPS location verification*2 ○ ○ × address. You can use the call and SMS functions without changing settings. (○: Available ×: Not available) *1 If you are using services in sp-mode, you do ■■Available areas not need to change access point. This FOMA terminal can be used in 3G network Turn on the data roaming setting to perform and GSM/GPRS network service areas, as well as in data communication when roaming. countries and areas supporting 3G850MHz/ → P.141 GSM850MHz network. Please check the available If you are using mopera U (スマートフォン定 areas. 額) (Smartphone flat-rate), you need to Before using the FOMA terminal overseas, see change access point. → P.140 the following items. *2 Packet communication charges are incurred Using Overseas • "Mobile Phone User's Guide [International during GPS measurement (finding current Services]" location). • DOCOMO "International Services website" NOTE NOTE Some services are not available depending on For a country code, international call access the overseas operator or network being used. code, universal number international prefix, and For information about overseas operators that information about countries, regions, overseas you can access, see "Mobile Phone User's Guide operators that you can access, see "Mobile [International Services]" or the DOCOMO Phone User's Guide [International Services]" or "International Services website". the DOCOMO "International Services website".
137 Check Before Using Your Preliminary Settings Terminal Overseas ■■About network services If you are subscribed to the network services, Checks to do before departure you can operate the Voice mail service, Call forwarding service, and Caller ID display request When you use the FOMA terminal overseas, service overseas. However, some network check the following while you are still in services are unavailable. Japan. To use network services overseas, you must ■■Your contract set "Remote access" to start. You can also set Check whether you have applied for WORLD "Remote access" once reaching your WING. For more details, contact "General destination. For more information, see Inquiries" at the last page of this instruction "Mobile Phone User's Guide [International manual. Services]". The network services, even if they can be set ■■Battery charging on/off, may not be available depending on the Using the FOMA terminal overseas may overseas operator you connect. consume battery power more than in domestic use. Checks to do in the country you Details on the handling of the AC adapter (optional) → P.23 stay Charging with the AC adapter (optional) When you arrive overseas, the FOMA → P.39 terminal automatically connects to an Using Overseas ■■Charges available network operator when it is powered on. Overseas usage charges (call and packet communication) are different from those in ■■About connections Japan. The FOMA terminal automatically searches for Some FOMA terminals and applications make and then connects to the network of another communications automatically and may incur available operator when you enable "Select high communication charges. automatically" for "Network operators" in the Please confirm the application's behavior with "Mobile networks" setting. its developers.
138 You can use packet communication service ■■Setting the date and time overseas at a flat-rate pricing by manually If the date and time are configured to update connecting to the operator providing desired automatically, the time and time zone of the service in "Network operators". To use the FOMA terminal's clock will be automatically flat-rate pricing service, you are required to changed when information about the local time subscribe to it. For details, see "Mobile Phone and time zone is received from the network of User's Guide [International Services]" or the the overseas operator to which you are DOCOMO "International Services website". connected. → P.96 If you are using mopera U, data Automatic setting may not work properly communication is available when roaming by depending on the network of the overseas setting access point for a pay-for-use plan. operator. Set manually in such a case. You can use that access point at a flat rate if The timing of these changes varies depending you are subscribing to a flat-rate service and on the overseas operator. set the network operator providing the If you stay in a country that uses daylight flat-rate pricing service. saving time, check the difference between the If you have used the access point for a local time and the time displayed on the pay-for-use plan, switch the access point to FOMA terminal. Automatic clock setting may "mopera U (スマートフォン定額)" (Smartphone not be available depending on the network flat-rate) before returning to Japan.→ P.140 operators. If you do not switch the access point in Japan, ■■Inquiries you may incur costly communication charges. If your FOMA terminal or UIM is lost or stolen ■■About screen display overseas, contact DOCOMO immediately from Using Overseas The type of network you are using is indicated in your current location and carry out the the status bar on the screen. procedure to suspend usage. For contact : Roaming information, contact "General Inquiries" / : Connected to/using GPRS provided on the last page of this manual. / : Connected to/using 3G (packet) Please note that you are liable for any call or The network operator you are connecting is communication charges incurred after the loss shown on Notifications panel. or theft of the FOMA terminal. You will need the country's international call access code or universal number international prefix if calling from a land-line phone from overseas.
139 After returning to Japan ■■Setting an operator ▶ "Network operators" ▶ "Select When you return to Japan, the FOMA automatically" or tap the network of the terminal automatically connects to the operator you want to use FOMA network. If it is unable to connect, • The operator names that are displayed change the following settings. vary depending on the setting of the Set "Network Mode" to "WCDMA/GSM "Network Mode". auto". → P.140 In the settings of "Network operators", set ■■Enabling data roaming "Available networks" to "Select ▶ Mark the "Data roaming" checkbox ▶ automatically". → P.140 "OK" ■■Switching access points → P.140 Network Settings for Use Overseas Switching access points If an access point is set to "mopera U (スマー Your FOMA terminal is configured to トフォン定額) (Smartphone flat-rate)", you automatically detect and switch the must switch the access point to use the network mode, operator, etc. by default, network overseas. but you can also manually switch. If an access point is set to "spモード", you can use the access point without any changes. 1 From the Home screen, m ▶ "Setting" ▶ "Wireless & 1 From the Home screen, m ▶ Using Overseas networks" ▶ "Mobile networks" "Setting" ▶ "Wireless & ■■Configuring Network Mode networks" ▶ "Mobile networks" ▶ "Network Mode" ▶ select any item: ▶ "Access Point Names" WCDMA only······Uses 3G network. 2 m ▶ "New APN" GSM only······Uses GSM network. WCDMA/GSM auto······Automatically "Name" ▶ enter the name of the switches to network that can be connected 3 network profile to create ▶ "OK" to. "APN" ▶ enter "mopera.net" ▶ 4 "OK"
140 5 m ▶ "Save" 3 " "
Tap the radio button of the Using international dialing assistance 6 created access point You can easily make an international call to NOTE a country registered with "Init'l dial If you have used mopera.net, switch the access assistance", when calling from your point to "mopera U スマートフォン定額" destination to another country, using the (Smartphone flat-rate) when you return to Japan international roaming service. (P.47). If you do not switch the access point, You must set "Init'l dial assistance" you may incur costly communication charges, so beforehand. → P.141 be sure to switch. Only enabled when a number begins with "0". Making/Receiving Calls while From the application list screen, at Destination 1 "Phone" ▶ enter the number ▶ " " Making calls to other countries "Dial (XX)" (XX: country/region (including Japan) while overseas 2 name) You can use the international roaming • "+" and "Country code" are added and service to make calls to other countries the international call is made. while overseas. Using Overseas ■■Configuring international dialing 1 From the application list screen, assistance "Phone" From the Home screen, m ▶ Enter + (touch and hold "0") ▶ 1 "Setting" ▶ "Call settings" ▶ 2 country code ▶ area code (city "Init'l dial assistance" code) ▶ enter the number Select any item: • If the area code (city code) begins with 2 "0", omit "0". Automatic int'l call······Set whether to You may need to dial "0" at the make an international call using the beginning of the number for calls to international dialing assistance setting. some countries and regions, such as Italy. 141 Country code······Register the country/ NOTE region name and country code used when When you receive a call while using the using the international dialing assistance international roaming service, the call is setting. forwarded internationally from Japan, regardless of the country from which the call is made. The Making domestic calls while caller incurs call charges for the call to Japan, overseas and the receiver incurs incoming call charges. Dial the other party's land-line phone Procedure for the other party to make a number or mobile phone number in the call to you same way as in Japan. → P.70 ■■Having the other party call you Making calls to WORLD WING users overseas from Japan overseas Have the other party call you simply by dialing When the other party that you are calling is your number in the same way as when you are a WORLD WING user, make an international in Japan. call to Japan, even if the other party is in ■■Having the other party call you the country in which you are staying. overseas from outside Japan Dial "+" and "81" (country code of Japan) You need to have the other party dial the first and then dial the phone number omitting international access code + "81" (Japan country the "0" at the beginning, as when you make code) regardless of the destination. an international call to Japan, because the call International access code-81-90 (or 80) Using Overseas is routed through Japan regardless of where -xxxx-xxxx the other party is. Receiving calls while overseas You can receive calls overseas in the same way as when in Japan.
142 Appendix/Index
Introduction to Options and Troubleshooting (FAQs) Related Devices You can expand the range of the FOMA Troubleshooting terminal's uses, in both the personal and First, check whether a software update is business realms, by combining it with required. If required, update the software. various optional devices. Some products → P.151 may not be available in certain areas. If a symptom does not improve after its cause For more details, please contact a service has been identified, contact "Repairs" (in counter such as a docomo Shop. Japanese only) at the last page of this For details on optional devices, see the instruction manual or a repair counter specified by DOCOMO. related instruction manuals. • Battery Pack N28 ■■Power supply • Back Cover N54 Power does not turn ON. • Desktop Holder N34 Is the battery pack inserted P.38 • FOMA microUSB Adapter N01 for charging correctly? • FOMA AC Adapter 01*/02* Is the battery pack charged? P.41 • FOMA AC Adapter 01 for Global use* • Carry Case 02 ■■Charging • FOMA DC Adapter 01*/02* Cannot charge (Notification LED does not light
• Wireless Earphone Set 02 or blinks). Appendix/Index • Wireless Earphone Set P01 Is the battery pack inserted P.38 • Bluetooth Headset F01 correctly? • AC Adapter F01 for Bluetooth Headset Is the adapter power plug securely P.42 • FOMA Portable Charging Adapter 02* connected to an electric outlet or • FOMA Dry Battery Adapter 01* cigarette lighter socket? • Bone Conduction Microphone/Receiver 02 * FOMA microUSB Adapter N01 for charging is required.
143 If you are using the FOMA microUSB P.41 If you use the camera function or - Adapter N01 for charging and the view/record 1Seg for a long time, AC adapter (optional), is the FOMA the FOMA terminal may become hot microUSB Adapter N01 for charging and the camera function or 1Seg correctly connected to the AC may end. Wait a while before adapter and to the FOMA terminal? restarting to use the camera If using the supplied desktop holder, function or 1Seg. is the AC adapter securely Battery usage time is short. connected to the desktop holder? Has the FOMA terminal been out of - If using the desktop holder, are the - the network service area for a long FOMA terminal's charging terminals time? soiled? If soiled, wipe the terminals with As the FOMA terminal searches for a dry cotton swab. radio waves in order to enable If you are using a microUSB cable - communication when out of the for PC connection (sample), is the network service area, more PC powered on? electricity is consumed than usual. If you make a call, perform data - The battery pack usage time varies P.40 communication, or use some other depending on the usage conditions function for a long time while and the degradation level. charging, the FOMA terminal may The battery pack is a consumable. P.40 become hot and charging may be The available usage time shortens stopped. In this case, charge again every time the battery pack is after the FOMA terminal cools recharged. down. If the usage time significantly
Appendix/Index reduces compared to the time of ■■Operation of the terminal purchase even if the battery pack is Becomes hot during operations or charging. fully charged, purchase the specified The FOMA terminal, battery pack, or - battery pack. adapter may become hot during operations or charging, or if you use the camera function or view/record 1Seg for a long time while charging. This is not a safety hazard, so you can continue to use them. 144 Power turns off or automatic restart occurs. Screen response to tapping or key press is slow. If the battery pack terminal is dirty, - The screen response may slow down - the contact may become poor and if large amounts of data are saved in the power may be turned off. If the FOMA terminal or transferred dirty, wipe the battery pack between the FOMA terminal and terminals with, for example, a dry the microSD card. cotton swab. The UIM is not recognized. No operation occurs by tapping or pressing a Is the UIM inserted in the right P.36 key. direction? Is the FOMA terminal turned off? P.44 The clock shows wrong time. Are you touching the touch panel P.44 If power is kept on for a prolonged P.96 correctly? time, the clock may show the wrong Is the screen locked? P.44 time. Is the FOMA terminal in sleep P.44 Check that the date and time are set mode? Press the power key to to "Automatic", and turn the cancel sleep mode. terminal off then back on in a Tapping does not work properly. location with good signal reception. Do you tap the screen with gloved P.44 ■■Telephone call hands? The ringtone does not sound. Do you tap with the tip of a P.44 Is the FOMA terminal in Silent P.88 fingernail, or is there any foreign mode? matter between your hand and the screen? Is the ring time for the Voice mail PP.76, service or Call forwarding service set 78 Is the display covered with a P.44 Appendix/Index to "0 sec."? protective sheet? Some types of protective sheets prevent correct Is the ringtone volume set to its P.88 operation. minimum? If you cover the proximity sensor P.34 with your hand, the ringtone volume may be lower. Cannot make a call with shown. Are you out of the service area or in P.53 a place with poor signal strength? 145 Cannot make a call ( does not disappear ■■Camera when you move, or calls cannot be made or Photos and videos shot with the camera are received even when the radio wave is strong blurred. enough). Check whether the lens is cloudy or - Turn the power off and then on, or - has dirt on it. remove and reinsert the battery pack When shooting an object close to P.110 or UIM. you, switch auto focus to "Close- You may not be able to make or - up". receive calls, depending on the type Is image stabilization set to "OFF"? P.110 of radio signal, even when is Is auto focus set to "AF OFF"? P.110 shown. Move to another place and call again. When shooting a person, switch P.110 auto focus to "Face detection (AF Depending on how congested the - ON)". radio waves are, it may be difficult to establish a connection in crowded ■■1Seg places due to a congestion of calls Cannot view 1Seg. and emails. Are you out of the terrestrial digital - ■■Screen TV broadcasting service area or in a The display is dim. place where airwaves are weak? Has the time set with "Screen P.88 Are the channels set? P.128 timeout" elapsed? ■■Osaifu-Keitai Is the FOMA terminal in eco mode? P.89 Cannot use the Osaifu-Keitai. Has "Brightness" setting changed? P.88
Appendix/Index Is Osaifu-Keitai lock set? P.132 Is battery level low? P.88 You may not be able to use the - ■■Sound Osaifu-Keitai function regardless of the Osaifu-Keitai lock setting if the During a voice call, the other party's voice is battery pack is removed from the difficult to hear or is too loud. FOMA terminal. To use the Osaifu- Has the call volume been changed? P.70 Keitai function, turn on the power once.
146 Do you wave the FOMA terminal P.131 Suddenly FOMA terminal becomes unusable over a reader with the e mark while overseas. facing the reader? Have you exceeded you maximum - call charge limit? ■■Using overseas A maximum call charge limit is FOMA terminal becomes unusable while preset in the WORLD WING overseas (although is displayed). international roaming service. If you Have you applied for WORLD CALL? - have exceeded your maximum call Check the subscription status. charge limit, you can restart the FOMA terminal becomes unusable while services by paying the accumulated overseas ( is displayed). call charges. Are you outside the international - No caller ID is displayed/A notified caller ID is roaming service area or in a place different from that of the caller/Functions that with poor signal strength? use Contacts data or caller ID notifications do Refer to "Mobile Phone User's not work. Guide [International Services]" and Even when a caller notifies the caller - DOCOMO "International Services ID, it is not displayed on the FOMA website" to check whether a service terminal unless notified from the area or network operator is network or network operator used. available. And, a notified caller ID may be Change the network settings and P.140 different from that of the caller by operator settings. some networks or networks • Set "Network Mode" to "WCDMA/ operators you use. GSM auto". ■■Data management • Set "Network operators" to "Select Appendix/Index automatically". Data transfer is not working. The FOMA terminal may be usable by - Are you using a USB hub? If you use P.117 rebooting. a USB hub, data transfer may not Data communication is not available while work properly. overseas. Activate "Data roaming" setting. P.141
147 ■■Infrared data exchange This message appears if you turn on P.92 Cannot receive all contact data. the power or attempt to perform an Is there available space in FOMA - operation related to the UIM while terminal memory? the PIN unblocking key is locked. In case of space shortage while Contact a docomo Shop Service receiving data, data transfer is Counter. stopped at that point. The received data is saved to the destination. Warranty and After-Sales ■■Bluetooth function Service FOMA terminal cannot find or be connected to a Bluetooth enabled device. Warranty Put the Bluetooth enabled device P.84 Be sure to receive a warranty at the time of (commercial) on standby and register purchase of the FOMA terminal. Read it on the FOMA terminal. If you contents of the warranty, confirm information want to delete a registered device such as the "Shop name and date of and register it again as a new purchase" and keep it in a safe place. If device, you must delete the necessary items are not described, registered device from both the immediately contact the shop of purchase. Bluetooth enabled device The warranty for free repair is valid for one (commercial) and the FOMA terminal year from the date of purchase. before you register it again. This product and its accessories are subject to modified, in part or whole, for improvement Error message without prior notice. Appendix/Index Data saved in your contacts, etc. may be SIM card is PUK-locked. modified or lost due to the malfunction, repair Refer to the user's guide or contact customer or other handling of the FOMA terminal. You support. should therefore make a copy of your contacts This message appears when you P.92 data, etc. as a precautionary measure. If you turn on the power while PIN1 code have the FOMA terminal repaired, most of the is locked. Tap "Emergency call" and previously downloaded data will not be enter " 05 [PUK code] transferred to the repaired terminal, as [new PIN1 code] [new PIN1 prohibited by the Copyright Act. code]#". * You can back up contacts data from the 148 FOMA terminal to a microSD card. After-sales service ■■Repair may not be possible in the following cases: For problems with your FOMA terminal • When a repair counter judges the cause of malfunction is exposure to water (Example: Before requesting repairs, read when wet-indication sticker reacts) "Troubleshooting" in this instruction • When, as the result of inspection, corrosion is manual. If the problem still persists, contact found due to exposure to water, condensation "Repairs" (in Japanese only) at the last page or sweat, or any of the internal boards are of this manual. damaged or deformed (damage to the external connector terminal (earphone/ For repairs after inquiry microphone terminal) or LCD or cracked body Bring your FOMA terminal to a repair could be the case as well) counter specified by DOCOMO. Repairs are * Since these conditions are outside the scope accepted during business hours of a repair of the warranty, any repairs, if at all possible, counter. Also, you must bring the warranty. will be charged. Note that it may take some days to repair ■■After expiration of the warranty the terminal depending on the malfunction All repairs that are requested are charged. state. ■■Replacement parts ■■During the warranty period Replacement parts (parts required to maintain • The FOMA terminal is repaired at no charge functions) will in principle be kept in stock for 6 under the conditions of the warranty. years after termination of production. However, • Make sure to bring the warranty for repair. depending on the malfunctioning part, repair You will be charged even during the warranty may not be possible due to a lack of period if the warranty is not presented or the replacement parts. Even after the stock period
trouble or damage is caused by your has expired, the repair of some malfunctioning Appendix/Index inappropriate handling (such as damage to parts may be possible. You should therefore LCD or connector, etc.). contact "Repairs" (in Japanese only) at the last • You will be charged even during the warranty page of this manual. period if malfunction is caused by the use of devices and consumables other than those specified by DOCOMO.
149 Precautions It should be noted that if the plate is Never modify the FOMA terminal or removed or is replaced with a different accessories. plate, and the original model plate • Doing so may result in fire, injuries or cannot be verified, it may disqualify the malfunctions. unit from repairs due to not being able to • The modified FOMA terminal may be determine the technical standards of that repaired only if the owner agrees on particular phone. that all the modified parts are restored Note that the settings and other to the original conditions. However, information may be reset (cleared) as a repairs may be refused depending on result of malfunction, repair or other the modifications. handling of the FOMA terminal. In this The following cases may be considered as case, make the settings again. modifications. When the repair is executed, MAC • Put a sticker on portions such as of address of Wi-Fi/Bluetooth address in the the LCD or keys. terminal may be changed regardless of • Glued decorations on the FOMA repaired part. terminal using adhesion bond, etc. Magnetic components are used in the • Change the parts such as exterior to parts of the FOMA terminal that are other than DOCOMO standard parts. described below. Do not allow cash cards • Malfunction and damage due to or other devices that are vulnerable to modifications will be repaired at the magnetism to come into contact with the owner's expense, even if the warranty phone. period is still effective. Parts where magnetic components are
Appendix/Index The model plate must not be removed used: area under camera, speaker, from the FOMA terminal. earpiece, and around mouthpiece The model plate certifies that the FOMA terminal satisfies technical standards.
150 The FOMA terminal has waterproof Updating Software capability, however, if the inside of the FOMA terminal has gotten wet or moist, Software Update is a function that immediately power off the terminal and connects to the network to check remove the battery pack from it, and whether software on FOMA terminal then bring it to the DOCOMO-specified needs to be updated, downloads a repair office as soon as possible. portion of the software by packet However, note that we may not repair communication as and when required, the FOMA terminal depending on the and updates the software. The NTT extent of the damage. DOCOMO website provides information about required software updates. There are three ways to update software: Memory dial (Contacts function) auto update, immediate update, and and downloaded data booked update. When you change the model or repair the • Auto update: FOMA terminal, data that has been imported, Automatically download software, and downloaded or created by you may be overwrite (update) it at a time set changed or lost. DOCOMO shall have no beforehand. liability for any change or loss of any kind. • Immediate update: Under some circumstances, DOCOMO may Update whenever you want to update. replace your FOMA terminal with its • Booked update: equivalent instead of repairing it. The data Book a time to install an update package, stored in your FOMA terminal will not be and the software is updatead transferred to the new terminal (some of the
data may be able to be transferred). automatically at the booked time. Appendix/Index Before updating software Do not remove the battery pack while updating software. This may result in a failed update. Fully charge the battery pack before updating software. Software cannot be updated in the following circumstances. 151 • During a call/when outside service area If the software has already been updated, a • During international roaming message appears to inform you that no • Airplane mode update is needed when you check for • When connected to a Wi-Fi network software updates. • During a major update SMS messages sent to you during a software • When the date/time are not correctly set update are stored at the SMS center. • When the battery level is too low for During a software update, your FOMA software update terminal information (model and • When there is insufficient free space for manufacturing numbers) are automatically software update sent to a software update server managed by Software update (download, installation) may DOCOMO. DOCOMO shall not use this take a long time. information for any purpose other than During a software update, you cannot make software update. or receive calls, use any communication If the software update fails, a message function, or use any functions (calls can be appears to inform you that the rewrite failed received during downloading). and no further operation may be possible. In When updating software, the FOMA terminal this case, please take the FOMA terminal to a performs SSL/TLS communication with the repair counter specified by DOCOMO. server (DOCOMO site). If a PIN code has been set, you will need to We recommend that you update software enter the PIN code when you restart the without moving and when you have strong FOMA terminal after the update has been reception (4 wave-level bars). installed. * If the reception deteriorates during a Do not start any other applications during a software update or the download is software update. stopped, move to a location with a better
Appendix/Index NOTE reception and start the software update You can update software while still retaining again. data (such as contacts, camera images, email, A message appears to inform you that you downloaded data, etc.) on the FOMA terminal. cannot update during international roaming Please note, however, that such data may not be or when outside the service area. protected, depending on the state of the FOMA When there is insufficient battery level for a terminal (malfunction, damage, exposure to software update, a message appears to inform water, etc.). It is recommended to back up you that charge is insufficient for updating. necessary data. Please note that some data, such as downloaded data, cannot be backed up.
152 Automatically updating software Configuring automatic update (auto update) From the Home screen, m ▶ You can automatically download new 1 "Setting" ▶ "About phone" ▶ software, which will overwrite the old software at a time you set beforehand. "Software Update" ▶ "Configure The auto update setting is set to "Automatic the software update" Update" by default. Once the FOMA terminal becomes ready to overwrite the old software, (Software update is available) appears in the status bar, and after checking the overwrite time, you can select to change the overwrite time, immediately overwrite, etc. When the overwrite time arrives while (Software update is available) is displayed, the old software is automatically overwritten, and (Software update is available) is no longer displayed. At times such as when there is insufficient battery level or you are in a call when the overwrite time arrives, the software update does not start, and instead starts at the same time on the next day. Software cannot automatically update when
the automatic update setting is "Manual Appendix/Index Update", during data communication for an immediate software update, etc. Tap the action when a 2 notification appears for software update • To update software automatically: "Automatic Update"
153 • Not to update software automatically: Select the overwrite method "Manual Update" 2 • When a software update is required, the overwrite time is displayed. Operation when an update is required ■■Starting overwriting at a specified (Software update is available) appears in time the status bar once software is automatically ▶ "OK" downloaded. • The display returns to the Home screen. Overwriting starts when the set time arrives. • appears in the status bar when overwriting is completed. no longer appears after being checked. ■■Changing the overwrite start time • Set the time for installing the update package. ▶ Go to step 1 of "Booking a time to update software" → P.157 ■■Starting overwriting immediately ▶ Go to step 1 of "Updating software immediately" → P.156 NOTE (Software update is available) appears in the status bar if the software update was not able to
Appendix/Index launch at the automatic update time.
Open the Notifications panel, 1 " "
154 Launching a software update 2 "OK" (immediate update) • Update starts after the terminal restarts. • All operations are disabled during an From the Home screen, m ▶ update. You also cannot cancel an 1 "Setting" ▶ "About phone" ▶ update. "Software Update" ▶ "Start the • The terminal restarts twice automatically during an update. software update" ▶ "Yes" • Once download starts, the software automatically updates. • Canceling a download partway deletes all data downloaded until then. Appendix/Index
The Home screen appears 3 • appears in the status bar. no longer appears after being checked.
• If an update is not required, "No update is needed." appears. 155 Updating software immediately After the terminal restarts, 3 software update starts 1 "Starts update" automatically • All operations are disabled during an update. You also cannot cancel an update. • Once an update is completed, the terminal restarts automatically in about 5 seconds. Open the Notifications panel, 4 " " • The software update completes, and the Home screen is displayed. 2 "Ready for update. Please keep • (Update completed) appears in the application clear" ▶"OK" status bar to indicate an update is • Overwriting starts automatically about 3 completed. (Update completed) no seconds after "Ready for update. Please longer appears after being checked. keep application clear" is displayed. • All operations are disabled during overwriting. You also cannot cancel overwriting. • Once overwriting is completed, the terminal restarts automatically. Appendix/Index
156 Display after a software update is Booking a time to update software completed (booked update) appears in the status bar. Open the If you want to book a different time for Notifications panel and tap the notification. installing an update package, you can set a A message notifying you that a software time for updating software beforehand. update is completed appears. "Sets Time" 1 • The screen for setting an overwrite start time appears. • The current FOMA terminal time is displayed.
Enter the desired time ▶ "Set" 2 • Set the time. • Tap "+" / "-" to change the update time, Appendix/Index and then tap "Set".
157 When the booked time arrives • If the FOMA terminal is turned off when the time booked for a software update arrives, the software is updated when the same time is again reached after turning on the terminal. Major Update You can upgrade the version of your FOMA terminal's OS (major update). For precautions on a major update, refer to "Before updating software" under "Updating Software". → P.151 1 "Ready for update. Please keep For the latest software information, refer application clear" appears ▶ to the manufacturer's site (MEDIAS NAVI): "OK" http://www.medias.net/ (in Japanese only) • The software update starts automatically From the Home screen, m ▶ about 3 seconds after "Ready for update. 1 "Setting" ▶ "About phone" ▶ Please keep application clear" is displayed. "Major updates" • Before the time booked for a software Select any item: update arrives, be sure to display the 2 Home screen and be in a location with Update now······Launch a major update. good signal reception. Updates by network······Upgrade the
Appendix/Index • If there is insufficient battery level for a OS version via a network. software update at the booked time, Updates by SD card······Upgrade the software is updated at the same time on OS version via an microSD card. the next day. Confirmation of update······Check • Software is not updated at the booked whether the FOMA terminal is able to time if during a major update. update. • If an alarm or other function is set for a time that coincides with a booked time, Auto update······Regularly check update the software update takes priority. information automatically, and check whether you can upgrade the version.
158 ■■Using "Updates by network" • if there is insufficient battery level for a Since major updates are carried out via major update microSD card, you must insert a microSD card • if there is insufficient free space on a beforehand. microSD card for a major update You cannot carry out a major update: • After the major update is completed, • During international roaming manually delete the update software • While in Airplane mode downloaded to your microSD card (the • While mounting during USB connection software can be safely removed once the • If there is insufficient battery level for a major update has completed normally). major update • If there is insufficient free space on a microSD card for a major update Packet communication charges are incurred for a major update using a 3G network. Since packet communication charges can become costly, a flat-rate packet rate is strongly recommended. Connection to a Wi-Fi network may be necessary depending on the version of the software to be updated. Before updating software via a Wi-Fi network, configure Wi-Fi settings beforehand and check that the terminal is connected to a Wi-Fi network. → P.48
■■Using "Updates by SD card" Appendix/Index To carry out a major update, connect your FOMA terminal to a PC (P.117), and download the update software from the manufacturer's site (MEDIAS NAVI) to a microSD card by the PC. For more information, refer to the manufacturer's site (MEDIAS NAVI). You cannot carry out a major update: • While mounting during USB connection 159 Main Specifications
■■Phone Product name N-06C Dimensions Approx. 128 mm (height) × approx. 64 mm (width) × approx. 7.9 mm (thickness) (Approx. 9.7 mm at the thickest part) Weight Approx. 113 g (with battery pack) Memory ROM 1,024 MB RAM 512 MB Continuous FOMA/3G Stationary (when "auto" is set*1): Approx. 340 hours standby time Moving (when "3G" is set*1): Approx. 260 hours Moving (when "auto" is set*1): Approx. 180 hours GSM Stationary (when "auto" is set*1): Approx. 220 hours Continuous FOMA/3G Approx. 250 minutes call time GSM Approx. 250 minutes Charging time AC adapter: Approx. 170 minutes DC adapter: Approx. 170 minutes 1Seg viewing time Approx. 300 minutes Display Type TFT 262,144 colors Size Approx. 4.0 inches Pixels 409,920 pixels (480 × 854 dots) Image pickup Type CMOS Appendix/Index device Size 1/4.0 inch Effective pixels Approx. 5.1 million pixels Camera Recorded pixels Approx. 5.0 million pixels (maximum) Digital zoom Approx. 6.7 times max.
160 Recorder Number of photos When recorded in the microSD card (2 GB): Approx. 9,999 that can be photos max.*2 recorded Continuous photo Shooting interval 0.04/0.1 seconds: 5 to 25 photos; Shooting shooting interval 0.5/1/2 seconds: 5 to 100 photos Photo file format JPEG Video recording When recorded in the microSD card (2 GB): Approx. 1,162 time minutes max.*3 Video file format MP4 1Seg recording When recorded in the microSD card (2 GB): Approx. 600 time minutes max. (total)*4 Audio WMA file Approx. 1,000 minutes*5 MP3 file Approx. 1,000 minutes*5 Wireless LAN*6 IEEE802.11b/g/n (2.4GHz band) compliant Bluetooth Compliant version Bluetooth Specification Version 2.1 + EDR compliant*7 Power Bluetooth Specification Power Class 2 Line-of-sight Up to approx. 10 m communication distance*8 Compliant profile HSP,HFP,A2DP,AVRCP,OPP,PBAP,SPP *1 To set the network connection change, use "Mobile networks" (P.82). *2 This is the maximum number of photos that can be saved to 1 folder, when Size = VGA (640 × 480) and Quality = Normal (file size = 95 KB). Appendix/Index *3 This is the recording time per video under the following conditions: Size = QCIF (176 × 144), Quality = Normal *4 The maximum recording time depends on the broadcaster and program recorded. *5 Background playback is supported. *6 The wireless LAN of this product has received Wi-Fi certification. *7 It is confirmed that this FOMA terminal and all Bluetooth devices are compliant with Bluetooth standards designated by Bluetooth SIG, and they are authenticated. However, procedures may differ or data transfer may not be possible depending on the device's characteristics or specifications.
161 *8 The available connection distance may be extremely shorter depending on the ambient environment (wall, furniture, etc.) or building structure. ■■Battery pack Product name Battery pack N28 Battery type Lithium ion battery Nominal voltage 3.8 V DC Nominal capacity 1230 mAh Appendix/Index
162 Specific Absorption Rate (SAR), The technical regulations and international guidelines set out limits for radio waves as etc. of Mobile Phones the Specific Absorption Rate, or SAR, which is the value of absorbed energy in any 10 Specific Absorption Rate (SAR) of grams of tissue over a 6-minute period. The SAR limit for mobile phones is 2.0 W/kg. The Mobile Phones highest SAR value for this mobile phone This model N-06C mobile phone complies when tested for use at the ear is 0.353 W/kg. with Japanese technical regulations and There may be slight differences between the international guidelines regarding exposure SAR levels for each product, but they all to radio waves. satisfy the limit. This mobile phone was designed in The actual SAR of this mobile phone while observance of Japanese technical operating can be well below that indicated regulations regarding exposure to radio above. waves*1 and limits to exposure to radio This is due to automatic changes to the waves recommended by a set of equivalent power level of the device to ensure it only international guidelines. This set of uses the minimum required to reach the international guidelines was set out by the network. Therefore in general, the closer International Commission on Non-Ionizing you are to a base station, the lower the Radiation Protection (ICNIRP), which is in power output of the device. collaboration with the World Health This mobile phone can be used in positions Organization (WHO), and the permissible other than against your ear. This mobile limits include a substantial safety margin phone satisfies the international guidelines designed to assure the safety of all persons, when used with a carrying case or a regardless of age and health condition. wearable accessory approved by NTT DOCOMO, INC.*2 In case you are not using Appendix/Index the approved accessory, please use a product that does not contain any metals, and one that positions the mobile phone at least 1.5 cm away from your body.
163 The World Health Organization has stated *1 Technical regulations are defined by the that present scientific information does not Ministerial Ordinance Related to Radio Law indicate that there are harmful effects (Article 14-2 of Radio Equipment attributed to the use of mobile devices. They Regulations). recommend that if you are worried about *2 Regarding the method of measuring SAR your exposure then you can limit your usage when using mobile phones in positions or simply use a hands-free kit to keep the other than against the ear, international mobile device away from the head and standards (IEC62209-2) were set in March body. of 2010. Please refer to the WHO website if you On the other hand, technical regulation is would like more detailed information. currently being deliberated on by national http://www.who.int/docstore/peh-emf/ council. (As of June 2011) publications/facts_press/fact_japanese.htm Radio Frequency (RF) Signals Please refer to the websites listed below if THIS MODEL PHONE MEETS THE U.S. you would like more detailed information GOVERNMENT'S REQUIREMENTS FOR regarding SAR. EXPOSURE TO RADIO WAVES. Ministry of Internal Affairs and Your wireless phone contains a radio Communications Website: transmitter and receiver. Your phone is http://www.tele.soumu.go.jp/e/sys/ele/index. designed and manufactured not to exceed htm the emission limits for exposure to radio Association of Radio Industries and frequency (RF) energy set by the Federal Businesses Website: Communications Commission of the U.S. http://www.arib-emf.org/index02.html (in Government. These limits are part of Japanese only) comprehensive guidelines and establish Appendix/Index NTT DOCOMO, INC. Website: permitted levels of RF energy for the http://www.nttdocomo.co.jp/english/ general population. The guidelines are product/sar/ based on standards that were developed by NEC CASIO Mobile Communications, Ltd. independent scientific organizations Website: through periodic and thorough evaluation http://www.n-keitai.com/lineup/sar/ (in of scientific studies. Japanese only) The exposure standard for wireless mobile phones employs a unit of measurement known as the Specific Absorption Rate (SAR).
164 The SAR limit set by the FCC is 1.6 W/kg.* The FCC has granted an Equipment Tests for SAR are conducted using standard Authorization for this model phone with all operating positions accepted by the FCC reported SAR levels evaluated as in with the phone transmitting at its highest compliance with the FCC RF exposure certified power level in all tested frequency guidelines. SAR information on this model bands. Although the SAR is determined at phone is on file with the FCC and can be the highest certified power level, the actual found under the Display Grant section at SAR level of the phone while operating can https://gullfoss2.fcc.gov/oetcf/eas/reports/ be well below the maximum value. This is GenericSearch.cfm after search on FCC ID because the phone is designed to operate at A98-PUL1905. multiple power levels so as to use only the For body worn operation, this phone has power required to reach the network. In been tested and meets the FCC RF exposure general, the closer you are to a wireless base guidelines when used with an accessory station antenna, the lower the output. designated for this product or when used Before a phone model is available for sale to with an accessory that contains no metal the public, it must be tested and certified to and that positions the handset a minimum the FCC that it does not exceed the limit of 1.5 cm from the body. established by the U.S. government-adopted requirement for safe exposure. The tests are Non-compliance with the above restrictions performed on position and locations (for may result in violation of FCC RF Exposure example, at the ear and worn on the body) guidelines. as required by FCC for each model. The ------highest SAR value for this model phone as * In the United States, the SAR limit for wireless reported to the FCC when tested for use at mobile phones used by the public is 1.6 watts/ the ear is 0.74 W/kg, and when worn on the kg (W/kg) averaged over one gram of tissue. body, is 0.48 W/kg. (Body-worn SAR values may vary depending upon national Appendix/Index measurements differ among phone models, reporting requirements and the network band. depending upon available accessories and FCC requirements). While there may be differences between the SAR levels of various phones and at various positions, they all meet the U.S. government requirement.
165 FCC Regulations • Consult the dealer or an experienced radio/TV technician for help. This mobile phone complies with part 15 of the FCC Rules. Operation is subject to the Changes or modifications not expressly following two conditions: (1) This device approved by the party responsible for may not cause harmful interference, and (2) compliance could void the user’s authority this device must accept any interference to operate the equipment. received, including interference that may cause undesired operation. Declaration of Conformity This mobile phone has been tested and found to comply with the limits for a Class B The product "N-06C" is declared to conform digital device, pursuant to Part 15 of the with the essential requirements of European FCC Rules. These limits are designed to Union Directive 1999/5/EC Radio and provide reasonable protection against Telecommunications Terminal Equipment harmful interference in a residential Directive 3.1(a), 3.1 (b) and 3.2. The installation. Declaration of Conformity can be found on This equipment generates, uses and can http://www.n-keitai.com/lineup/index.html radiate radio frequency energy and, if not (Japanese only). installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is This mobile phone complies with the EU no guarantee that interference will not requirements for exposure to radio waves. occur in a particular installation; if this Your mobile phone is a radio transceiver, equipment does cause harmful interference designed and manufactured not to exceed to radio or television reception, which can the SAR* limits** for exposure to radio- frequency (RF) energy, which SAR* value, Appendix/Index be determined by turning the equipment off and on, the user is encouraged to try to when tested for compliance against the correct the interference by one or more of standard was 0.568 W/kg. While there may the following measures: be differences between the SAR* levels of Reorient or relocate the receiving antenna. various phones and at various positions, • Increase the separation between the they all meet*** the EU requirements for RF equipment and receiver. exposure. • Connect the equipment into an outlet on a * The exposure standard for mobile phones circuit different from that to which the employs a unit of measurement known as receiver is connected. the Specific Absorption Rate, or SAR. 166 ** The SAR limit for mobile phones used by the Export Administration public is 2.0 watts/kilogram (W/kg) averaged over ten grams of tissue, recommended by Regulations The Council of the European Union. The This product and its accessories may be limit incorporates a substantial margin of safety to give additional protection for the under coverage of the Export public and to account for any variations in Administration Regulations of Japan measurements. ("Foreign Exchange and Foreign Trade *** Tests for SAR have been conducted using Control Laws" and the related laws and standard operating positions with the phone regulations). When exporting this transmitting at its highest certified power product and its accessories, take necessary level in all tested frequency bands. Although procedures on your responsibility and the SAR is determined at the highest expense. For details, contact Ministry of certified power level, the actual SAR level of Economy, Trade and Industry of Japan. the phone while operating can be well below the maximum value. This is because Intellectual Property Right the phone is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, Copyright and portrait rights the closer you are to a base station antenna, You have no right to copy, modify, or the lower the power output. distribute contents such as text, images, music, or software downloaded from websites on the Internet, or images captured by the camera of this product without permission from the copyright holder except when the copy or quote is for personal use Appendix/Index that is allowed under Copyright Law. Note that it may be prohibited to capture or record live performances or exhibitions even for personal use. Refrain from taking portraits of other people and uploading such portraits to websites using this product without their consent, as this violates portrait rights.
167 ® Trademarks • T9 is a trademark or registered trademark of Nuance • "FOMA", "i-mode", "i-αppli", "Deco-mail", Communications, Inc. and corporate "ToruCa", "mopera", "mopera U", "WORLD owners of Nuance in the United States and/or CALL", "iD", "WORLD WING", "sp-mode", other countries. "Melody Call" and "ToruCa" logo, "Osaifu- • PhotoSolid®, MovieSolid® and their logos are Keitai" logo, "iD" logo, "iC" logo are trademarks or registered trademarks of trademarks or registered trademarks of NTT Morpho Inc. in Japan and other countries. DOCOMO, INC. • "Google", "Android", "Android Market", • "Catch Phone (Call waiting service)" is a "Gmail", "Google Calendar", "Google Maps", registered trademark of Nippon Telegraph and "Google Talk", "Google Latitude", "YouTube", Telephone Corporation. "Picasa", "Google" logo, "Android" logo and • Powered by emblend™ Copyright 2010-2011 "Android Market" logo are trademarks or Aplix Corporation. All Rights Reserved. registered trademarks of Google Inc. emblend and emblend-related trademarks are • Wi-Fi®, WPA®, Wi-Fi CERTIFIED logo, and trademarks or registered trademarks of Aplix Wi-Fi Protected Setup logo are registered Corporation in Japan and other countries. trademarks of Wi-Fi Alliance. e • is a registered trademark of FeliCa • Wi-Fi CERTIFIED™ and Wi-Fi Protected Setup Networks, Inc. are trademarks of Wi-Fi Alliance. • The microSDHC logo is a trademark of SD-3C, LLC. • "PictMagic", "Quick Shot", "MEDIAS", "MEDIAS NAVI", and "PC Link" are • "らくらく無線スタート" is a registered trademarks or registered trademarks of NEC trademark of NEC AccessTechnica, Ltd. CASIO Mobile Communications, Ltd. • "Twitter" is a trademark or registered ® ® ®
Appendix/Index • Microsoft , Windows , Windows Media and trademark of Twitter, Inc. Windows Vista® are trademarks or registered • "mixi" is a registered trademark of mixi, Inc. trademarks of Microsoft Corporation in the • "Facebook" is a trademark or registered United States and/or other countries. trademark of Facebook, Inc. • Microsoft® Exchange ActiveSync® is a • "Evernote" is a trademark or registered trademark or registered trademark of trademark of Evernote Corporation. Microsoft Corporation in the United States • "BeeTV" is a trademark or registered and/or other countries. trademark of Avex Entertainment Inc. • "EVERYSTAR" is a registered trademark of EVERYSTAR Co., Ltd. 168 • "ATOK" is a registered trademark of • FeliCa is a contactless IC card technology JustSystems Corporation. developed by Sony Corporation. FeliCa is a registered trademark of Sony Corporation. • Contains Adobe® Flash® Player by Adobe • "andronavi", "ついっぷる" are trademarks or Systems Incorporated. registered trademarks of NEC BIGLOBE, Ltd. Adobe Flash Player Copyright© 1996-2011 • "mosimo camera" is a registered trademark Adobe Systems Incorporated. All rights of AITIA Corporation. reserved. • "Soradas" is a registered trademark of MTI Adobe, Flash and Flash logo are registered Ltd. trademarks or trademarks of Adobe Systems • This product uses "FontAvenue" of NEC Incorporated in the United States and/or other Corporation. countries. • Other company names or product names described in this manual are trademarks or registered trademarks of those companies. • The Bluetooth word mark and logos are owned by the Bluetooth SIG, INC. and any Others use of such marks by NTT DOCOMO, INC. is • This product is licensed in compliance with under license. Other trademarks and trade the MPEG-4 Visual Patent Portfolio License. names are those of their respective owners. You are allowed to use it for private nonprofit • ©MTI Ltd. purposes and only when: • Recording moving pictures that are Notational conventions for compliant with the standard of MPEG-4 Windows Visual (hereinafter referred to as MPEG-4 • The abbreviations of operating systems Video)
(Japanese versions) below are used in this Appendix/Index • Playing MPEG-4 Videos recorded personally manual. by consumers not engaged in profit activities • Windows 7 stands for Microsoft® Windows® • Playing MPEG-4 Video supplied from a 7 (Starter, Home Basic, Home Premium, provider licensed by MPEG-LA Professional, Enterprise and Ultimate). When using the product for any other • Windows Vista stands for Windows Vista® purpose, such as commercial promotion, (Home Basic, Home Premium, Business, internal use or profit, contact MPEG LA, LLC Enterprise and Ultimate). of the U.S.
169 • Windows XP indicates the Microsoft® For information on GPL and LGPL, from the Windows® XP Professional operating system Home screen, m ▶ "Setting" ▶ "About or Microsoft® Windows® XP Home Edition phone" ▶ "Legal information" ▶ "Open operating system. source licenses"
® ® ■■Obtaining source code Using Adobe Flash Player For information on obtaining source code, see • Adobe® Flash® Player embedded in this the following website. product ("Software") is protected by http://www.n-keitai.com/guide/download/ copyright laws. Be sure to observe the (in Japanese only) following rules when using the Software. Inquiries regarding the content of source code ①You shall not copy or distribute the cannot be responded to. Software. ②You shall not modify, adapt, translate or create derivative works based upon the Software. ③You shall not reverse engineer, decompile, disassemble, or otherwise attempt to discover the source code of the Software. ④You shall not make a claim for any consequential, indirect, incidental, special damages, or any lost profits by using the Software. GPL/LGPL-applicable software
Appendix/Index • This product contains software licensed complying with GNU General Public License (GPL) or GNU Lesser General Public License (LGPL). You can obtain the source code for the software and reproduce, redistribute, or modify the software in accordance with the GPL or LGPL.
170 Index Booking (1Seg)...... 129 Booking recording...... 129 Alphabets Booking viewing (1Seg)...... 129 Bookmarks...... 105 About Phone...... 96 Brightness (screen)...... 89 Accessibility (settings)...... 96 Browser...... 104 Accessories...... 1 Calculator...... 134 Access point...... 46 Calendar...... 134 Access point (overseas)...... 140 Caller ID notification service...... 80 Account...... 50 Call Forwarding service...... 78 Email account...... 50 Call Log...... 72 Setting...... 93 Call settings...... 88 After-sales service...... 148 Call volume...... 70 Airplane mode...... 83 Call Waiting service...... 77 Alarm...... 133 Camera...... 109 Alarm volume...... 88 Changing wallpaper...... 53 Android keyboard...... 67 Channel setting...... 128 Android Market...... 120 Charging...... 39 Applications Adapter...... 42 Installing...... 120 Desktop holder...... 41 List...... 57 PC...... 43 List screen...... 56 Charging with an AC adapter...... 42 Purchasing...... 121 Charging with an DC adapter...... 42 Setting...... 92 Charging with a PC...... 43 Appendix/Index Shortcuts...... 51 Charging with the adapter...... 42 Uninstalling...... 57 Charging with the desktop holder...... 41 Attaching/removing the back cover...... 29 Chat...... 103 Backlight...... 89 Check phone number (yours)...... 74 Battery pack...... 38 Clock (application)...... 133 Bluetooth Clock setting...... 96 Calling...... 70 Connecting to a PC...... 117 Communication...... 116 Contacts...... 73 Setting...... 116 171 Data roaming (overseas)...... 141 Formatting (microSD card)...... 94 Date setting...... 96 Gallery...... 112 Days...... 136 Gesture input...... 65 Declining calls...... 72 Gmail...... 99 Display (setting)...... 88 Google Maps...... 124 Docking a shortcut...... 52 Google Talk...... 103 docomo market...... 122 GPS...... 123 Drag...... 45 Gガイド番組表 (G-GUIDE)...... 129 Draining water...... 32 Handling precautions...... 21 Earphone/headphone connection...... 35 Home screen...... 51 eco mode...... 89 iD設定アプリ (iD appli)...... 135 Email Importing Email...... 98 Bookmarks...... 106 Email account...... 50 Contacts...... 74 Gmail...... 99 Email...... 98 SMS...... 102 SMS...... 102 sp-mode mail...... 99 Incoming calls history...... 72 Emergency call...... 70 Infrared data exchange...... 115 Entering emoticons...... 66 Initializing (FOMA terminal)...... 94 Entering smileys...... 66 Initial Settings...... 46 Entering symbols...... 66 Installing (applications)...... 120 Entering text...... 64 Intellectual propery right...... 167 Error messages...... 148 International dialing assistance setting Export Administration Regulations...... 167 ...... 141 Appendix/Index Exporting International roaming...... 137 Bookmarks...... 106 Keyboard Contacts...... 74 Android...... 67 Email...... 98 QWERTY...... 64 SMS...... 102 Settings...... 94 Flick...... 45 10-key...... 64 Flick input...... 66 Language (setting)...... 94 Folders (Home screen)...... 52 Latitude...... 126
172 Location Service...... 124 Options...... 1, 143 Location (setting)...... 89 Osaifu-Keitai...... 146 Main specifications...... 160 Osaifu-Keitai lock setting...... 132 Major update...... 158 Outgoing calls history...... 72 Making a call...... 70 Part names and functions...... 34 Making a call (overseas)...... 141 Party shuffle...... 113 Making a call overseas...... 71, 141 PC Link...... 117 Making an international call...... 71, 141 Phonebook (Contacts)...... 73 Market...... 120 PhoneBookCopy...... 75 Media playback volume...... 88 PIN1 code entry setting...... 91 microSD card...... 37 PIN1 code/PIN2 code...... 91 Accessing from a PC...... 117 PIN setting...... 90 Capacity...... 94 PIN unblocking key...... 92 Formatting...... 94 Places...... 126 Inserting/removing...... 37 Playback Mobile networks...... 82 Music...... 112 Mobile networks (overseas)...... 140 Photos...... 112 mopera U...... 47 Videos...... 112 Music Player...... 112 1Seg...... 129 MyProfile...... 74 Playlists (music)...... 113 Navigation...... 125 Precautions...... 7 Network Mode (overseas)...... 140 Privacy (setting)...... 93 Network operators (overseas)...... 140 Profile...... 74 Network security code...... 91 Program guide...... 129 Appendix/Index Network services...... 76 Public mode (power off)...... 80 Network (setting)...... 82 PUK code...... 92 Notification icons...... 54 Purchasing (applications)...... 121 Notification ringtone...... 88 Push tone...... 70 Notifications pannel...... 55 Putting a call on hold...... 70 Numeric keypad input...... 65 Quickoffice...... 135 Opening/closing the external connector QWERTY keyboard...... 64 terminal cap...... 29 Receiving a call...... 72
173 Receiving a call (overseas)...... 142 SMS...... 102 Receiving a call overseas...... 142 Sound (setting)...... 88 Receiving an international call...... 142 Specific Absorption Rate (SAR)...... 163 Related devices...... 143 sp-mode...... 47 Repositioning pages (Home screen)...... 51 sp-mode mail...... 99 Ringtone Status bar...... 53 Call...... 88 Status icons...... 53 Email...... 99 Street View...... 125 Gmail...... 101 Synchronize (setting)...... 93 SMS...... 103 T9 input...... 66 Ring volume...... 88 Tapping...... 45 SAR (Specific Absorption Rate)...... 163 Tap search...... 63 Screen Task Manager...... 63 Backlight...... 89 Time setting...... 96 Brightness...... 89 Toggling entry modes (text)...... 65 Display orientation...... 44 Topics...... 136 Lock...... 44 ToruCa...... 132 Screen lock security...... 90 Touch and hold...... 45 Settings...... 88 Touch panel operation...... 44 Zooming in/zooming out...... 45 Trademarks...... 168 Search Troubleshooting...... 143 Search-Google search...... 63 Turning power on/off...... 44 Search-Within web page...... 105 TV...... 126 Search (setting)...... 94 TV Link...... 129 Appendix/Index Security codes...... 90 UIM...... 36 Security (setting)...... 89 Uninstalling (applications)...... 57 Settings menu...... 82 Unlock security...... 89 Shooting photos...... 111 Updating software...... 151 Shooting videos...... 111 USB PC Link...... 117 Silent mode...... 88 Using overseas...... 137 Sleep mode...... 44 Vibration Slide...... 45 Email...... 99
174 Gmail...... 101 Incoming call...... 88 SMS...... 103 Voice Input & Output (setting)...... 95 Voice Mail service...... 76 Volume...... 88 VPN...... 87 Warranty...... 148 Waterproof function...... 27 Web page widget...... 106 Widgets List...... 62 Shortcuts...... 51 Wi-Fi access point...... 86 Wi-Fi settings...... 48, 83 Wireless (setting)...... 82 WORLD CALL...... 71 WORLD WING...... 137 Numerals 1Seg...... 126 10-key keyboard...... 64 Appendix/Index
175 You can view/change your contract contents, subscribe to services, and request information materials on the Internet. My docomo (http://www.mydocomo.com/) ⇒ 各種お申込・お手続き (Various Applications/Procedures) (in Japanese only) * You need your docomo ID and password in order to access this page. * If you do not have or you have forgotten your "docomo ID/password", contact "General Inquiries" at the last page of this instruction manual. * You may not be able to access the site depending on the content of your subscription. * You may not be able to access the site due to system maintenance, etc.
Using mobile phone with good manners! Please be considerate of others around you when using the FOMA terminal. Always turn OFF your FOMA terminal in the Be considerate of where you use your FOMA following situations terminal and keep your voice and ringtone down ■■In a place where the use of mobile phones is prohibited ■■Keep your voice down when using the FOMA Always turn off your FOMA terminal on an terminal in a quiet place such as a restaurant airplane and in a hospital. or hotel lobby. * Please note that medical electrical equipment is ■■If you are in an outdoor public place, make also used in other parts of a hospital in addition to sure you do not disturb others. its wards. Always turn off your FOMA terminal in lobbies and waiting rooms as well. Respect privacy ■■When you are in a place where you may be near to Please be considerate of the privacy of individuals people with implanted cardiac pacemakers or around you when shooting and sending photos implanted defibrillators, such as in a crowded train using camera-equipped mobile phones. The FOMA terminal may exert a harmful effect on implanted cardiac pacemakers and implanted defibrillators. The following functions will help you to keep Set your FOMA terminal to Public mode in the good manners in public following situations There are useful functions you can use to set your ■■While driving FOMA terminal not to answer incoming calls, and Using the mobile phone in your hand while driving to silence all sounds. is subject to punishment. However, this excludes ■■Airplane mode: enables/disables the function to situations when the use of a mobile phone is emit radio waves.→ P.83 unavoidable, such as the rescue of the sick and ■■Manner (Silent) mode: Silences the ringtone and injured or the maintenance of public safety. other sounds from the FOMA terminal.→ P.88 ■■When you are in a public place such as a ■■Public mode (Power off): A message plays theater, movie theater, or museum Using the notifying callers that you are where you have to FOMA terminal in a public place, where you power off the phone and cannot answer, and the phone automatically hangs up.→ P.80 need to be quiet, annoys people around you. ■■Vibrator: Notifies incoming calls by vibration. → P.88 General Inquiries Repairs
Loss or theft of FOMA terminal or payment of cumulative cost overseas Failures encountered overseas
Don’t forget your mobile phone … or your manners! When using your mobile phone in a public place, don't forget to show common courtesy and consideration for others around you. Sales: NTT DOCOMO, INC. To prevent damage to the environment, bring used battery Manufacturer: packs to a docomo service counter, a docomo agent or a 2011.06 (1st Edition) recycle center.