SPD, Power Conditioning, PF Capacitors and Harmonic Filters
Industrial Surge Protection Products 10.1 Introduction 10 Industrial and Commercial Surge Protection ...... 2 Datacom Protection ...... 2 10 Critical Load Protection...... 2 Telecommunications Protection ...... 3 10 Power Conditioning ...... 3 10 10.2 Surge Protective Devices (SPD) Product Overview ...... 6 10 SPD Series for Integration into Electrical Distribution Equipment ...... 8 10 SPD Series for Mounting External to Electrical Distribution Equipment . . . . . 12 CVL Surge Protective Device ...... 17 10 AEGIS Powerline Filters ...... 19 CVX050/100 ...... 22 10 Datacom ...... 25 10 10.3 Power Conditioning Products 10 Sag Ride Through (SRT) ...... 26 Electronic Voltage Regulator (EVR) ...... 32 10 10.4 Power Factor Correction Capacitors 10 Product Overview ...... 34 UNIPUMP ...... 37 10 UNIPAK ...... 40 AUTOVAR 300 Automatic Power Factor Correction Capacitor Systems . . . . . 51 10 AUTOVAR 600 Automatic Power Factor Correction Capacitor Systems . . . . . 54 10 AUTOVAR Filter—LV Automatic Harmonic Filter ...... 59 Transient-Free Static Switching Power Factor Correction Units ...... 63 10 Active-Harmonic Filter-Harmonic Correction Unit—NEMA 1 Enclosure . . . . . 67 10 10 10 10 10 10 10 10 10 10 10 10 10 10
Distribution Products Catalog CA08101001E—July 2010 www.eaton.com 1
10.1 SPD, Power Conditioning, PF Capacitors and Harmonic Filters Introduction
10 Industrial and Commercial Surge Protection Contents Description Page 10 Telecommunications Protection ...... 3 Power Conditioning ...... 3 10 Application Description ...... 4 Facility-Wide Power Protection Solutions ...... 5 10 10 10 10 10 10
10
10 Industrial and Commercial Surge Protection Critical Load Protection Datacom Protection 10 ● SPD Series for Integration SPD Series Sidemount Units ● AEGIS-HW: Series filters Eaton’s line of data and into Electrical Distribution Specification grade surge for up to 20 amperes, communication surge Equipment protective devices for single-phase (protection for suppression products are 10 ● SPD Series for Mounting installation external to PLCs, control equipment) available for nearly any External to Electrical electrical distribution ● AEGIS-VL: Hardwired configuration and offer 10 Distribution Equipment equipment. surge filter that protects complete protection for critical loads up to computers and small to 10 SPD Series Integrated Units 5 amperes large networks, including the following: Specification grade surge ● OEM components: 10 protective devices installed A wide variety of ● Modular protection for within Eaton’s electrical components for domestic/ multi-pair applications assemblies. international applications 10 ● Hardwire connected (including military) (one or two pair protectors) 10 ● Wiring connectors (D89, DB25 and RJ11) 10 ● Coaxial cable protection ● Mounting hardware 10
10 SPD Series Sidemount Unit 10 10
10 Datacom Products
10 AEGIS Products 10 SPD Series Integrated Unit 10 10 10 10
2 Distribution Products Catalog CA08101001E—July 2010 www.eaton.com
SPD, Power Conditioning, PF Capacitors and Harmonic Filters 10.1 Introduction
Telecommunications Protection 10 Eaton’s Telecommunication Panelboards with Integrated surge suppression products Surge Protective Devices are designed to safeguard ● Available in standard and 10 against harmful and potentially custom configurations disastrous surges and spikes. ● Ratings: 10 Our data communication and ● 120/240 Vac, single- telecommunication surge phase, three-wire 10 suppression solutions protect your equipment from the ● 208Y/120 Vac, three- damage frequently caused by phase, four-wire 10 lightning strikes, brownouts, ● 480Y/277 Vac, three- electrical load switching, faulty phase, four-wire 10 wiring, downed power lines ● 600Y/347 Vac, three- and more. This unique line phase, four-wire (other Surge Protective Devices can be 10 Integrated within a variety of Eaton was developed to protect voltage configurations Electrical Assemblies against the harmful are available) 10 surges that threaten your telecommunication circuits. ● Copper bus ● 12, 18, 24, 30, 36 and 10 42 circuits ● Bolt-on branch breakers 10 ● A full range of factory installed modifications 10 and accessories ● Fully rated or series rated 10
Power Conditioning 10
Sag Ride Through (SRT) Electronic Voltage 10 The sag ride through (SRT) Regulator (EVR) is a power conditioner that The electronic voltage 10 corrects voltage sags to regulator (EVR) is designed maintain uptime and to meet the needs of 10 productivity. customers who experience voltage regulation problems due to brownout conditions 10 from their electric utilities. 10 10 10 10 Sag Ride Through (SRT) Electronic Voltage Regulator (EVR) 10 10 10 10 10 10 10 10 10
Distribution Products Catalog CA08101001E—July 2010 www.eaton.com 3
10.1 SPD, Power Conditioning, PF Capacitors and Harmonic Filters Introduction
10 Application Description
10 Application Recommendations for Surge Products 10 Application Type Eaton’s Surge Product Features and Competitive Advantages Light Commercial 10 Design build SPD Series integrated units Ideal package for any commercial facility Chain stores SPD Series sidemount units Cost-effective, reliable protection using the SPD Series or CVL units 10 Small facilities CVL units CVX units 10 Large Projects Including: SPD Series integrated units in panelboards, switchboards, Able to meet competitors’ SPD specifications 10 Commercial MCCs, switchgear, busway and automatic transfer switches Increased surge protection performance by using integrated SPD Series units Government SPD Series sidemount units Wall space savings by using integrated SPD Series units 10 Schools CVL units Quick-ship capabilities from Eaton assembly satellites and service centers Institution Datacom surge protectors Power conditioning capability for a wide variety of applications 10 Military AEGIS units for critical load applications Power conditioners (EVR and SRT units) 10 Industrial Including: SPD Series integrated units in panelboards, switchboards, Increased surge protection performance by using integrated SPD Series units 10 Small and large facilities MCCs, switchgear, busway and automatic transfer switches Wall space savings by using integrated SPD Series units 10 WWTP SPD Series sidemount units MCCs with SPD Series units installed protect drives from damage CVL units AEGIS products protect expensive critical loads from harmful damage AEGIS units for critical load applications such as PLCs, EVR units correct voltage regulation problems 10 robotics applications, etc. SRT units correct voltage sag problems Power conditioners (EVR and SRT units) 10 OEM Any OEM customer including: SPD Series integrated units Years of experience in a variety of OEM applications 10 Integrators SPD Series sidemount units Application assistance and recommendations Medical equipment CVL units Small footprint enables integration in a variety of applications 10 Automation and control CVX units Ability to meet customized requirements Datacom surge protectors 10 AEGIS units for critical load applications 10 Telecommunications Including: Panelboards and automatic transfer switches with integrated SPD Series units Ability to meet customized requirements 10 Cellular sites SPD Series sidemount units Application assistance and recommendations Microwave CVL units 10 PCS CVX units Paging systems 10 10 10 10 10 10 10 10 10 10
4 Distribution Products Catalog CA08101001E—July 2010 www.eaton.com
SPD, Power Conditioning, PF Capacitors and Harmonic Filters 10.1 Introduction
Facility-Wide Power Protection Solutions 10 A facility-wide protection recommended design 1. Ensure proper 2. Surge protection should approach should be approach for implementing grounding conditions be installed at key employed to address power facility-wide Eaton power exist. All forms of power distribution panels 10 quality issues. This approach protection solutions. protection/conditioning and critical loads. minimizes overall lifecycle rely on good grounding, 10 costs and optimizes facility The most accepted design bonding and earthing uptime. The following is a methodology is based on practices. two concepts: 10 10 Application of Surge Protection, Voltage Regulation and Sag Correction Devices 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10
Distribution Products Catalog CA08101001E—July 2010 www.eaton.com 5
10.2 SPD, Power Conditioning, PF Capacitors and Harmonic Filters Surge Protective Devices (SPD)
10 SPD Series Sidemount Units Contents Description Page 10 Surge Protective Devices (SPD) SPD Series for Integration into Electrical 10 Distribution Equipment ...... 8 SPD Series for Mounting External to Electrical 10 Distribution Equipment ...... 12 CVL Surge Protective Device ...... 17 10 AEGIS Powerline Filters ...... 19 CVX050/100 ...... 22 10 Datacom ...... 25 Learn 10 Online 10 10
10
10 Product Overview 10 Product Description Features, Benefits and Functions Eaton’s SPD series surge A complete offering of ● Utilizes thermally Safety Features 10 protective devices are the sidemount units designed protected metal oxide ● All units utilize thermally latest and most advanced for mounting external to varistor (MOV) technology protected metal oxide ® 10 UL 1449 3rd Edition certified electrical distribution ● Three feature package varistor technology (MOV) surge protectors. Units are equipment is also available. options as their core surge available integrated within Application of SPD Series 10 ● True protection status suppression component. Eaton electrical assemblies, units throughout a facility indicators report the status Usage of this technology including panelboards, will ensure that equipment of the protection elements, ensures safe operation 10 switchboards, motor is protected with the safest not the status of the when the unit is subjected control centers, switchgear, and most reliable surge applied power to abnormal conditions automatic transfer switches protective devices available. 10 ● such as temporary and bus plugs. SPD Series units are available Available integrated within the following overvoltage or high fault in all common voltages and current conditions. Under 10 configurations and also Eaton electrical assemblies: panelboards, switchboards, such conditions, the in a variety of surge current thermally protected MOVs 10 capacity ratings from 50 motor control centers, switchgear, automatic are removed from the through 400 kA. Three circuit quickly and safely feature package options are transfer switches and 10 bus plugs before a potentially unsafe also available to choose from, condition can occur ensuring the proper unit is ● 10-year warranty 10 ● SPD Series units contain available for a variety of no replaceable parts such 10 SPD Series Integrated Units applications. as surge modules, fuses, or surge counter memory backup batteries. This 10 prevents potential arc flash and shock hazards, as the 10 units require no periodic service or user intervention 10 after installation ● Integrated versions of the 10 unit are factory installed and sidemount versions 10 are factory sealed. These important safety measures further enhance user 10 safety 10 10
6 Distribution Products Catalog CA08101001E—July 2010 www.eaton.com
SPD, Power Conditioning, PF Capacitors and Harmonic Filters 10.2 Surge Protective Devices (SPD)
Three Feature Package Standard Feature Package Side-By-Side Comparison of the SPD Series’ Available Options Available The standard feature package Feature Packages 10 The SPD Series provides includes all of the features Standard with users with the option of found in the basic feature Feature Package Comparison Basic Standard Surge Counter 10 package, plus an audible alarm selecting between three ■ ■■ with silence button, EMI/RFI Surge protection using thermally protected feature packages. These MOV technology 10 feature packages are the filtering, and a form ‘C’ relay ■■ ■ basic, standard and standard contact that can be used for Dual-colored protection status indicators for each phase with surge counter. The remote annunciation of the 10 proper feature package SPD’s status. The audible Dual-colored protection status indicators ■■ ■ can be selected based on alarm activates and the form for the N-G protection mode 10 the requirements of the ‘C’ relay contact changes state Audible alarm with silence button ■■ application or specification. when any loss of protection is Form ‘C’ relay contact ■■ 10 A side by side comparison of detected or a fault condition ■■ the individual features found exists with the unit. Should EMI/RFI filtering, providing up to 50 dB of noise attenuation from 10 kHz to 100 MHz 10 in each package is below. such a condition occur, the audible alarm can be silenced Surge counter with reset button ■ Basic Feature Package by pressing the silence button. 10 The basic feature package is The EMI/RFI filter provides up Standards and Certifications Technical Data perfect for applications where to 50 dB of noise attenuation ● Integrated versions of and Specifications 10 basic, cost-effective, safe and over the range of 10 kHz the unit are UL 1449 ● reliable surge protection is through 100 MHz. 20 kA nominal discharge required, but budgets don’t 3rd Edition recognized current (In) rating 10 allow for extra, additional Standard with Surge components for the (maximum rating features. Rather than Counter Feature Package United States and Canada, assigned by UL) 10 sacrifice performance or The standard with surge covered by Underwriters ● 50 through 400 kA surge safety due to cost, SPD counter feature package Laboratories certification current capacity ratings 10 and follow-up service Series units with the basic includes all of the features ● 200 kA short-circuit current feature package provide you found in the standard feature ● Sidemount versions are rating (SCCR) 10 with high-performing surge package plus a six-digit surge UL 1449 3rd Edition listed protection without sacrificing counter with a reset button. devices and are also safety or reliability. The basic The surge counter indicates CSA approved 10 feature package provides the ongoing count of the the same level of surge number of surges the unit has 10 protection and safety been exposed to and stores provided by the standard and them in nonvolatile memory. 10 standard with surge counter Should power to the SPD feature packages minus Series unit be completely some of the features found in interrupted, the surge counter 10 them. The package contains will recall and display the dual-colored protection status surge count prior to the 10 LEDs that report the true interruption when power is status of the protection in restored. Unlike many surge 10 each phase/mode. All four- protectors, the SPD Series’ wire plus ground units also surge counter memory 10 contain an additional set of feature does not require a dual-colored protection status backup battery that would LEDs that report the status require periodic replacement 10 of the protection in the in order to achieve its neutral/ground mode. memory functionality. 10 10 10 10 10 10 10 10 10
Distribution Products Catalog CA08101001E—July 2010 www.eaton.com 7 10.2 SPD, Power Conditioning, PF Capacitors and Harmonic Filters Surge Protective Devices (SPD)
10 SPD Series Unit Integrated within an Eaton Panelboard Contents Description Page 10 Product Overview ...... 6 SPD Series for Integration into Electrical 10 Distribution Equipment Standards and Certifications ...... 9 10 Catalog Number Selection ...... 9 Technical Data and Specifications ...... 10 10 Dimensions ...... 11 SPD Series for Mounting External to Electrical 10 Distribution Equipment ...... 12 CVL Surge Protective Device ...... 17 10 AEGIS Powerline Filters ...... 19 CVX050/100 ...... 22 10 Datacom ...... 25 10
10
10 SPD Series for Integration into Electrical Distribution Equipment 10 Product Description Application Description Eaton’s SPD Series surge The SPD Series is available as The Integrated SPD 10 protective devices are the an integrated device within Performance Advantage latest and most advanced the following Eaton electrical Installation conductor length 10 UL 1449 3rd Edition certified assemblies: is the single most important surge protectors. SPD Series factor related to an SPD’s ● Panelboards units are available in all performance. Performance 10 common voltages and ● Switchboards decreases as the connected configurations, and also in ● Motor control centers conductor length increases. 10 a variety of surge current ● Switchgear Integrating the SPD within the capacity ratings from ● Automatic transfer electrical assembly provides 50–400 kA. 10 switches the best possible surge protection by keeping ● 10 Bus plugs installation conductor lead Features, Benefits lengths as short as possible. Integrating the SPD within In this installation, the SPD Series and Functions is mounted directly to the panelboard’s 10 an electrical assembly can ● bus bars. This type of installation Uses thermally protected decrease let-through will provide the best possible surge metal oxide varistor (MOV) protection by minimizing the 10 voltages by hundreds of volts, connected lead length. technology providing you with the best 10 ● Three feature package possible surge protection for options sensitive electronic loads. ● 10-year warranty 10 Remote Display Mounting Option Available 10 The SPD Series offers the option of mounting its display 10 remotely from the device. This is useful for applications 10 where OEMs or other integrators would like to embed the unit within a piece 10 of equipment and still be able 10 to view its display.
10 The SPD Series is also available as an integrated unit interfaced via a circuit breaker resident in the electrical 10 assembly. This installation keeps connected lead lengths short while providing a means of disconnecting 10 power to the unit quickly and easily.
8 Distribution Products Catalog CA08101001E—July 2010 www.eaton.com SPD, Power Conditioning, PF Capacitors and Harmonic Filters 10.2 Surge Protective Devices (SPD)
Standards and Certifications ● UL 1449 3rd Edition 10 recognized component for the United States 10 and Canada, covered by Underwriters Laboratories 10 certification and follow-up service 10 ● UL 1283 (Type 2 SPDs only) 10 10 10 Catalog Number Selection 10
SPD Series Units Mounted Internal to Electrical Distribution Equipment 10 SPD 250 480D 2 J 10 10 Series Application—Integrated Units SPD = Surge protective device kA Rating A = Panelboards (PRL1a, 2a, 3a, 3E), direct bus mounted 10 050 = 50 kA per phase Voltage Code B = Switchgear (includes remote display) 080 = 80 kA per phase 240S = 120/240 single split-phase C = Panelboards (PRL1a, 2a, 3a, 3E, 4), switchboards, 100 = 100 kA per phase 208Y = 120/208 wye (4W+G) busway 10 120 = 120 kA per phase 220Y = 127/220 wye (4W+G) J = Motor control centers 160 = 160 kA per phase 400Y = 230/400 wye (4W+G) 200 = 200 kA per phase 480Y = 277/480 wye (4W+G) 10 Feature Package 250 = 250 kA per phase 600Y = 347/600 wye (4W+G) 300 = 300 kA per phase 240D = 240 delta (3W+G) 1 = Basic 10 400 = 400 kA per phase 480D = 480 delta (3W+G) 2 = Standard 600D = 600 delta (4W+G) 3 = Standard + surge counter 240H = 240 high-leg delta (4W+G) on ‘B’ phase 10 Notes 10 Please consult the factory for 240 high-leg Delta (4W+G) applications with high leg on ‘C’ phase. Units used in PRL1a, 2a, 3a and 3E panelboard applications are available in 50–200 kA ratings only. Use the ‘C’ option for PRL1a, 2a, 3a and 3E panelboard applications when unit is connected through a circuit breaker. 10 Example: SPD250480D2J = SPD Series, 250 kA per phase, 480D voltage, standard feature package, motor control center application. 10 10 10 10 10 10 10 10 10 10 10 10
Distribution Products Catalog CA08101001E—July 2010 www.eaton.com 9 10.2 SPD, Power Conditioning, PF Capacitors and Harmonic Filters Surge Protective Devices (SPD)
10 Technical Data and Specifications
10 SPD Series Specifications 10 Description Specification Surge capacity ratings available 50, 80, 100, 120, 160, 200, 250, 300, 400 kA per phase
10 Nominal discharge current (In) 20 kA (maximum rating assigned by UL) Short-circuit current rating (SCCR) 200 kA 10 SPD type Basic feature package = Type 1 (can also be used in Type 2 applications) Standard and standard with surge counter feature packages = Type 2 10 Single split-phase voltages available 120/240 Three-phase wye system voltages available 120/208, 127/220, 230/400, 277/480, 347/600 10 Three-phase delta system voltages available 240, 480, 600 10 Input power frequency 50/60 Hz Power consumption (basic units): 10 208Y, 220Y, 240S, 240D and 240H voltage codes 0.5W 400Y, 480Y and 480D voltage codes 1.1W 10 600Y and 600D voltage codes 1.3W 10 Power consumption (standard and standard with surge counter units): 208Y, 220Y, 240S, 240D and 240H voltage codes 0.6W 10 400Y, 480Y and 480D basic voltage codes 1.7W 600Y and 600D voltage codes 2.1W 10 Protection modes Single split-phase L-N, L-G, N-G, L-L Three-phase wye L-N, L-G, N-G, L-L 10 Three-phase delta L-G, L-L 10 Three-phase high-leg delta L-N, L-G, N-G, L-L Maximum continuous operating voltage (MCOV): 10 240S, 208Y, 220Y and 240H MCOV 150 L-N, 150 L-G, 150 N-G, 300 L-L 400Y and 480Y MCOV 320 L-N, 320 L-G, 320 N-G, 640 L-L 10 600Y MCOV 420 L-N, 420 L-G, 420 N-G, 840 L-L 240D MCOV 320 L-G, 320 L-L 10 480D MCOV 640 L-G, 640 L-L 10 600D MCOV 840 L-G, 840 L-L Ports 1 10 Operating temperature –40°F through 122°F (–40°C through 50°C) Operating humidity 5% through 95%, noncondensing 10 Operating altitude Up to 16,000 ft (5000m) 10 Seismic withstand capability Meets or exceeds the requirements specified in IBC 2006, CBC 2007 and UBC Zone 4 Form C relay contact ratings 150 Vdc or 125 Vac, 1A maximum Form C relay contact logic Power ON, normal state—NO contact = open, NC contact = closed 10 Power OFF or fault state—NO contact = closed, NC contact = open 10 EMI/RFI filtering attenuation Up to 50 dB from 10 kHz to 100 MHz 10 10 10 10 10 10
10 Distribution Products Catalog CA08101001E—July 2010 www.eaton.com SPD, Power Conditioning, PF Capacitors and Harmonic Filters 10.2 Surge Protective Devices (SPD)
Dimensions Approximate Dimensions in Inches (mm) 10 10 50—200 kA Integrated Units
Mounting 10 0.22 3x Bus Mounting 8.80 (5.6) (223.5) 4.40 10 0.19 (111.8) 4x Mounting 0.04 2.02 2.02 0.34 (4.8) 10 Bus (1.0) (51.2) (51.2) (8.6)
0.95 NEUTRAL 10 NEUTRAL NEUTRAL (24.1) NEUTRAL
5.40 10
Mounting CAUTION SPD Series (137.2) 3.42 Surge Protective Device 10 (86.9) 4.66 3.42 (118.4)
(86.9) FORM “C” CONTACTS
TORQUE
GROUND 10 NEU/GND
36 IN. LBS. SURGE SURGE GROUND SURGE
SURGE SURGE GROUND GROUND 10
2.52 3.42 0.22 0.26 4x Mounting (64.0) (86.9) (5.6) 10 (6.6) 3.45 Terminals 4x #10–32 x 0.38 DP (87.6) 8.74 Brass Terminals 10 (222.0) 9.50 (241.3) 10 10 250—400 kA Integrated Units
Mounting 10 8.80 4x Mounting (223.5) 10 2.52 3.42
(64.0) (86.9) 10 GROUND GROUND
SURGE SURGE
SURGE GROUND SPD Series SURGE
36 IN. LBS. IN. 36 Surge Protective Device 10 NEU/GND GROUND
3.42 Mounting TORQUE FORM “C” CONTACTS (86.9) 3.42 CAUTION 5.40 10 (86.9) (137.2) 4.66 10 (118.4)
TORQUE NEU/GND 1.71 36 IN. LBS. 10
NEUTRAL NEUTRAL
NEUTRAL (43.4) NEUTRAL 10 Terminals 0.22 4.85 4x Mounting (123.2) 8.74 (5.6) (222.0) 10 5.78 9.50 4x #10–32 x 0.38 DP (146.8) (241.3) Brass Terminals 10 Weights 10 ● 50–200 kA units approximately 3.5 lbs (1.6 kg) 10 ● 250–400 kA units approximately 7.0 lbs 10 (3.2 kg) 10 10 10
Distribution Products Catalog CA08101001E—July 2010 www.eaton.com 11 10.2 SPD, Power Conditioning, PF Capacitors and Harmonic Filters Surge Protective Devices (SPD)
10 Eaton SPD Series Sidemount Unit Mounted Externally to an Eaton Panelboard Contents Description Page 10 Product Overview ...... 6 SPD Series for Integration into Electrical 10 Distribution Equipment ...... 8 SPD Series for Mounting External to Electrical 10 Distribution Equipment Catalog Number Selection ...... 13 10 Technical Data and Specifications ...... 14 Dimensions ...... 15 10 CVL Surge Protective Device ...... 17 AEGIS Powerline Filters ...... 19 10 CVX050/100 ...... 22 10 Datacom ...... 25 10
10
10 SPD Series for Mounting External to Electrical Distribution Equipment 10 Product Description Features, Benefits Standards and Certifications Eaton’s sidemount versions and Functions ● UL 1449 3rd Edition 10 of the SPD Series surge ● Uses thermally protected listed device protective devices are the metal oxide varistor (MOV) ● Canadian Standards 10 latest and most advanced technology Association (CSA) UL 1449 3rd Edition listed ● Three feature package ● UL 1283 (Type 2 surge protectors. Application options SPDs only) 10 of SPD Series units ● 10-year warranty throughout a facility will 10 ensure that equipment is protected with the safest and 10 most reliable surge protective devices available. Units are All SPD Series sidemount units come available in all common prewired and include a factory- 10 voltages and configurations, installed conduit interface, and also in a variety of surge making installation very easy. 10 current capacity ratings from 50 through 400 kA. Three 10 feature package options are also available to choose from. 10 10
All SPD Series units are factory sealed, 10 ensuring that the user/installer has no potential of coming into contact with harmful voltages present 10 inside the unit. 10 10 10 10 10 10
12 Distribution Products Catalog CA08101001E—July 2010 www.eaton.com SPD, Power Conditioning, PF Capacitors and Harmonic Filters 10.2 Surge Protective Devices (SPD)
Catalog Number Selection 10 SPD Series Units for Mounting External to Electrical Distribution Equipment 10 SPD 250 480D 2 K 10
Series Application—Sidemount Units 10 SPD = Surge protective device kA Rating K = NEMA 1 enclosure 050 = 50 kA per phase Voltage Code L = NEMA 1 flushmount enclosure 10 080 = 80 kA per phase 240S = 120/240 single split-phase M = NEMA 1 enclosure with internal disconnect 100 = 100 kA per phase 208Y = 120/208 wye (4W+G) N = NEMA 4 enclosure 10 120 = 120 kA per phase 220Y = 127/220 wye (4W+G) O = NEMA 4 enclosure with internal disconnect 160 = 160 kA per phase 400Y = 230/400 wye (4W+G) P = NEMA 4X enclosure (stainless steel) 200 = 200 kA per phase 480Y = 277/480 wye (4W+G) Q = NEMA 4X enclosure with internal disconnect 10 250 = 250 kA per phase 600Y = 347/600 wye (4W+G) (stainless steel) 300 = 300 kA per phase 240D = 240 delta (3W+G) 400 = 400 kA per phase 480D = 480 delta (3W+G) 10 600D = 600 delta (4W+G) Feature Package 240H = 240 high-leg delta (4W+G) on ‘B’ phase 1 = Basic 10 2 = Standard 3 = Standard + surge counter 10 Notes Please consult the factory for 240 high-leg delta (4W+G) applications with high leg on ‘C’ phase. 10 NEMA 1 flushmount units are available in 50–200 kA ratings only. Example: SPD250480D2K = SPD Series, 250 kA per phase, 480D voltage, standard feature package, housed in NEMA 1 enclosure. 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10
Distribution Products Catalog CA08101001E—July 2010 www.eaton.com 13 10.2 SPD, Power Conditioning, PF Capacitors and Harmonic Filters Surge Protective Devices (SPD)
10 Technical Data and Specifications 10 SPD Series Specifications Description Specification 10 Surge capacity ratings available 50, 80, 100, 120, 160, 200, 250, 300, 400 kA per phase Nominal discharge current (In) 20 kA (maximum rating assigned by UL) 10 Short-circuit current rating (SCCR) 200 kA SPD type Basic feature package = Type 1 (can also be used in Type 2 applications) 10 Standard and standard with surge counter feature packages = Type 2 Single split-phase voltages available 120/240 10 Three-phase wye system voltages available 120/208, 127/220, 230/400, 277/480, 347/600 10 Three-phase delta system voltages available 240, 480, 600 Input power frequency 50/60 Hz 10 Power consumption (basic units): 208Y, 220Y, 240S, 240D and 240H voltage codes 0.5W 10 400Y, 480Y and 480D voltage codes 1.1W 600Y and 600D voltage codes 1.3W 10 Power consumption (standard and standard with surge counter units): 10 208Y, 220Y, 240S, 240D and 240H voltage codes 0.6W 400Y, 480Y and 480D basic voltage codes 1.7W 10 600Y and 600D voltage codes 2.1W Protection modes Single split-phase L-N, L-G, N-G, L-L 10 Three-phase wye L-N, L-G, N-G, L-L 10 Three-phase delta L-G, L-L Three-phase high-leg delta L-N, L-G, N-G, L-L 10 Maximum continuous operating voltage (MCOV): 240S, 208Y, 220Y and 240H MCOV 150 L-N, 150 L-G, 150 N-G, 300 L-L 10 400Y and 480Y MCOV 320 L-N, 320 L-G, 320 N-G, 640 L-L 600Y MCOV 420 L-N, 420 L-G, 420 N-G, 840 L-L 10 240D MCOV 320 L-G, 320 L-L 10 480D MCOV 640 L-G, 640 L-L 600D MCOV 840 L-G, 840 L-L 10 Ports 1 Operating temperature –40°F to 122°F (–40°C to 50°C) 10 Operating humidity 5% through 95%, noncondensing Operating altitude Up to 16,000 ft (5000m) 10 Seismic withstand capability Meets or exceeds the requirements specified in IBC 2006, CBC 2007 and UBC Zone 4 10 Enclosure dimensions and weights Refer to figures on pages 15–16 for enclosure dimensions and weights Form C relay contact ratings 150 Vdc or 125 Vac, 1A maximum 10 Form C relay contact logic Power ON, normal state—NO contact = open, NC contact = closed Power OFF or fault state—NO contact = closed, NC contact = open 10 EMI/RFI filtering attenuation Up to 50 dB from 10 kHz to 100 MHz 10 10 10 10 10 10
14 Distribution Products Catalog CA08101001E—July 2010 www.eaton.com SPD, Power Conditioning, PF Capacitors and Harmonic Filters 10.2 Surge Protective Devices (SPD)
Dimensions Approximate Dimensions in Inches (mm) 10 50–200 kA Units in a NEMA 1 Rated Enclosure, 50–200 kA Units in a NEMA 1 Rated Flushmount Enclosure, 10 Weight = 6.8 lbs Weight = 6.8 lbs
7.28 7.28 10 (184.9) 1.00 Flushmount Panel (184.9) 1.00 5.27 (25.4) (4) #8–32 Flat Hd Screws 5.27 (25.4) (133.9) (133.9) 10 10
10.48 12.05 (306.1) (266.2) 8.00 10 (203.2) 12.05 10.48 11.25 11.25 10 (306.1) (266.2) (285.8) 0.68 (285.8) 0.68 5.24 (17.3) 14.00 5.24 (17.3) (133.1) (355.6) 10 (133.1) Ø0.20 (Ø5.1) Ø0.20 10 (Ø5.1) 0.78 5.00 2.00 (19.8) 0.11 0.40 3.48 (127.0) 10 (50.8) 7.47 0.40 2.00 (88.4) (2.8) (10.2) 7.47 0.78 (189.7) (10.2) (50.8) 4.41 3.48 1.76 (189.7) 0.98 (19.8) (88.4) (112.0) (44.7) 11.00 (24.9) 10 4.41 (279.4) (112.0) 10 250–400 kA Units in a NEMA 1 Rated Enclosure, 50–400 kA Units in a NEMA 1 Rated Enclosure with Internal 10 Weight = 13.5 lbs Disconnect, Weight = 14.7 lbs
1.00 6.69 9.14 10 5.47 (25.4) (169.9) (232.2) (138.9) 10
12.30 0.66 10 12.05 (312.4) (16.8) 10.48 11.50 (306.1) 11.25 10 (266.2) 2.61 10.73 (292.1) (285.8) (66.3) (272.5) 0.67 5.24 (17.0) 10 (133.1) 10 Ø0.20 Ø0.20 2.75 2.00 0.78 (69.9) (Ø5.1) 11.14 (Ø5.1) 7.47 0.78 (50.8) 0.40 (19.8) 5.76 (283.0) 10 5.76 (189.7) (19.8) (10.2) (146.3) (146.3) 6.69 6.55 (169.9) (166.4) 10 10 10 10 10 10 10 10 10 10
Distribution Products Catalog CA08101001E—July 2010 www.eaton.com 15 10.2 SPD, Power Conditioning, PF Capacitors and Harmonic Filters Surge Protective Devices (SPD)
10 Approximate Dimensions in Inches (mm) 50–200 kA Units in a NEMA 4 or 4X Rated Enclosure, 50–400 kA Units in a NEMA 4 or 4X Rated Enclosure with 10 Weight = 14.6 lbs Internal Disconnect, Weight = 27.5 lbs
10 13.50 SPD Series SPD Series (342.9) Surge Protective Device 12.50 Surge Protective Device 12.75 (317.5) 11.75 11.98 (323.9) 10 (304.3) (298.5) 12.28 10.98 3.12 (311.9) 10 (278.9) 11.28 (79.2)
(286.5)
0.65 Device Protective Surge
5.49 Series SPD
0.65 Device Protective Surge (16.5) (139.4) Series SPD 10 (16.5)
0.76 3.36 10.18 Ø0.33 10 2.60 (19.3) (85.3) (258.6) (Ø8.4) 0.76 6.00 12.47 (66.0) 7.68 (19.3) (152.4) Ø0.33 (195.1) (316.7) 10 5.39 8.65 (Ø8.4) (136.9) (219.7) 10 250–400 kA Units in a NEMA 4 or 4X Rated Enclosure, 10 Weight = 14.6 lbs 10 SPD Series Surge Protective Device 10.98 11.28 10 (278.9) (286.5) 11.75 12.50 (298.5) 10 (317.5)
5.49 0.65 Device Protective Surge
10 (139.4) (16.5) Series SPD
10 4.10 6.00 0.76 (104.1) (152.4) Ø0.33 (19.3) 7.68 8.65 (8.4) 10 (195.1) (219.7) 10 10 10 10 10 10 10 10 10 10 10 10 10 10
16 Distribution Products Catalog CA08101001E—July 2010 www.eaton.com SPD, Power Conditioning, PF Capacitors and Harmonic Filters 10.2 Surge Protective Devices (SPD)
CVL Contents 10 Description Page Product Overview...... 6 10 SPD Series for Integration into Electrical Distribution Equipment ...... 8 10 SPD Series for Mounting External to Electrical Distribution Equipment ...... 12 10 CVL Surge Protective Device Catalog Number Selection ...... 18 10 AEGIS Powerline Filters ...... 19 CVX050/100 ...... 22 10 Datacom ...... 25 10 10 10
10
CVL Surge Protective Device 10 Product Description Features, Benefits Standards and Certifications 10 This surge protection device and Functions ● UL 1449 listed, UL 1283 is used to prevent downtime ● SurgePlane™ technology listed, CSA approved 10 and equipment damage. to ensure reliability and ● The UL 1283 listed filter performance by using a Eaton’s CVL is a commercial protects against ringing 10 low impedance copper grade and light industrial transients and EMI/RFI platform surge protective device noise disturbances. The 10 (SPD) that combines surge ● Compact design to tuned suppression filter suppression components and enable close mounting achieves 40 dB attenuation 10 EMI/RFI filtering to provide to electrical distribution at 100 kHz effective protection for equipment sensitive electronic loads. ● Parallel hybrid filter 10 technology ● Individually fused surge 10 suppression components ● Status indicator lights to 10 monitor supply power, surge suppression 10 component status and fusing 10 ● Can be remotely monitored using Form C contacts 10 ● Audible alarm 10 ● Ideal for OEM panel applications 10 ● Proven track record in international applications 10 10 10 10 10 10
Distribution Products Catalog CA08101001E—July 2010 www.eaton.com 17 10.2 SPD, Power Conditioning, PF Capacitors and Harmonic Filters Surge Protective Devices (SPD)
10 Catalog Number Selection 10 CVL 10 CVL CH BD
10 kA Rating Voltage Code Enclosure 050 = 50 kA/phase 240S = 120/240 Single split-phase RSX = NEMA 1 10 080 = 80 kA/phase 208Y = 120/208 Wye (4W+G) R3R = NEMA 3R 100 = 100 kA/phase 400Y = 230/400 Wye (4W+G) 120 = 120 kA/phase 480Y = 277/480 Wye (4W+G) 10 160 = 160 kA/phase 240D = 240 Delta (3W+G) 200 = 200 kA/phase 480D = 480 Delta (3W+G) 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10
18 Distribution Products Catalog CA08101001E—July 2010 www.eaton.com SPD, Power Conditioning, PF Capacitors and Harmonic Filters 10.2 Surge Protective Devices (SPD)
AEGIS Solutions Contents 10 Description Page Product Overview...... 6 10 SPD Series for Integration into Electrical Distribution Equipment ...... 8 10 SPD Series for Mounting External to Electrical Distribution Equipment ...... 12 10 CVL Surge Protective Device ...... 17 AEGIS Powerline Filters 10 Standards and Certifications ...... 20 Catalog Number Selection ...... 21 10 Technical Data and Specifications ...... 21 CVX050/100 ...... 22 10 Datacom ...... 25 10 10
10
AEGIS Powerline Filters 10 Product Description Application Description Features, Benefits and Functions 10 Eaton’s AEGIS solutions are The AEGIS is the ideal AEGIS powerline filters specifically designed to protection solution for your protect against the full 10 protect expensive electronics critical loads and facilities. spectrum of transient from the hazards that exist disturbances. within a facility. This critical Loads 10 AEGIS filters the entire sine load protection is effective ● Programmable wave and is effective against at reducing harmful surges controllers (PLCs) 10 both frequently occurring low and noise. Applying this ● Scanning devices high performance series energy and occasional high 10 ● powerline filter at your ATMs (Automatic Teller energy transients. High critical loads results in Machines) energy transients can create 10 “clean” power entering the ● Cash registers immediate damage, while electronics and reduction of ● Alarm systems low energy transients cause microprocessor failure 10 “soft” errors, operational ● Microprocessor-controlled over time. malfunction and damage OEM products AEGIS VL Hardwired Critical Load Filter to components. 1, 3 and 5 Ampere Modules Only 10 ● Robotics ● CAD/CAM systems 10 ● Control equipment ● Medical electronics and 10 devices
Why Should Sensitive Electronic 10 Loads be Protected? PLC manufacturers 10 and service technicians recommend the use of 10 surge suppressors and filters Hardwired Surge Filter that Protects Critical Loads (3, 5, 10, to prevent downtime and 15 or 20 Ampere Models) 10 equipment damage due to surges and electrical line noise. One study shows 10 failure to protect sensitive electronic loads costs 10 American manufacturing, commercial and service 10 industries over $39 billion per year in lost time and revenue. Preventing these losses is a 10 major cost-saving opportunity. 10
Distribution Products Catalog CA08101001E—July 2010 www.eaton.com 19 10.2 SPD, Power Conditioning, PF Capacitors and Harmonic Filters Surge Protective Devices (SPD)
AEGIS Powerline Filters 10 Features Benefits Unique series hybrid design Protection against high and low energy transients and noise. 10 (AEGIS-HW) The tracking filter reacts instantly to changes in frequency and voltage, regardless of phase angle, magnitude or polarity. Active at all times, providing more protection than a conventional surge suppressor. 10 Extends the life of your microprocessors by eliminating degrading power disturbances. High performance suppression capabilities AEGIS-HW and AEGIS-PR have up to 45,500 amperes of surge current suppression and 75 dB of noise attenuation at 100 kHz. 10 (AEGIS-HW) This guarantees a superior level of protection and reliability. Status monitoring lights No more testing or guessing whether your unit is working properly. Filter indicator lights expedite your troubleshooting efforts during 10 (AEGIS-HW) downtime situations. 5-year downstream equipment warranty Eaton provides a 5-year extended warranty on the microprocessor power supply protected by AEGIS. No other manufacturer offers this level 10 (AEGIS-HW only) of assurance in backing up its claim of product performance, quality and reliability. Value (AEGIS-HW) AEGIS provides superior value when considering the level of performance and benefits offered. It truly delivers the best “bang” for your dollar. 10 Optional remote monitoring capabilities Observe all your operations on a remote basis, including the power protection devices used to safeguard your critical and sensitive (AEGIS-HW, AEGIS VL only) electronic loads. 10 DIN rail, J-rail or flange mounting connections The DIN rail mountable enclosures greatly reduce installation time, effort and cost. This unique container is the preferred choice among OEMs (AEGIS-HW only) and contractors. 10 Thermal cut-off protection (TCO) Thermal fuse improves indication, monitor and control during fault conditions. (AEGIS-HW only) 10 AEGIS Hybrid Series Powerline Filters 10 Three-Wire Design has Normal and Common Mode Protection (L-N, L-G, N-G) 10 Primary Transient High Series High Status Optional Voltage Surge Frequency Blocking Performance Secondary Indicator Form C 10 Suppression (TVSS) Capacitor Inductors Track ing Filter TVSS Lights Contacts Power Input Power 10 Output L Normal Normal LED Form C L 10 Mode Mode
10 N N 10 Common Common G G 10 Mode Mode 10 Standards and Certifications 10 ● UL 1283 ● CSA 10 10 Note 10 Option for AEGIS. 10 10 10 10 10 10 10
20 Distribution Products Catalog CA08101001E—July 2010 www.eaton.com SPD, Power Conditioning, PF Capacitors and Harmonic Filters 10.2 Surge Protective Devices (SPD)
Catalog Number Selection 10 AEGIS-HW AEGIS-VL 10 AGSHW CH X AGSVL 10
Voltage Code Current Capacity Options Voltage Code Current Capacity 10 120N 03 = 3A S = Standard 120N 1 = 1A 230L 05 = 5A C = Form C contact for 230L 3 = 3A 10 10 = 10A remote monitor 5 = 5A 15 = 15A 20 = 20A 10 10 Technical Data and Specifications
Specifications 10 AEGIS-HW AEGIS-VL Application 2 W&G Grounded Systems 2 W&G Grounded Systems 10 Input voltage single-phase 120, 220, 240 Vac, single-phase 120, 220, 240 Vac, single-phase 10 Amperage 3, 5, 10, 15, 20 amperes 1, 3, 5 amperes Frequency 50/60 Hz 50/60 Hz 10 Protection modes L-N, L-G, N-G L-N, L-G, N-G MCOV 150, 320 volts 150, 320 volts 10 Noise attenuation 10 Normal mode: 75 dB at 100 kHz 75 dB at 100 kHz Common mode: 50 dB at 5 MHz 50 dB at 5 MHz 10 Filter bandwidth 10 kHz to 100 MHz 10 kHz to 100 MHz Total peak surge current 45.5 kA per phase 39 kA per phase 10 Operating temperature –40ºF to +122°F (–40ºC to +50°C) –40ºF to +122°F (–40ºC to +50°C) Response time Less than 1 nanosecond Less than 1 nanosecond 10 Options Form C relay contacts N/A 10 IEEE C62.41 (2002) Test Waveforms for AEGIS-HW and VL Versions 10 Category A Ringwave (Line-to-Neutral) (6000V, 200A) Category B Combination (Impulse) Wave (6000V, 3000A) 10 8000 7000 700 6000 600 6000 5000 500 400 4000 400 10 4000 300 3000 300 ts 2000 ts
l 200 2000 200 l 100 1000 100 Vo Vo 10
Volts 0 0 0 0
Volts -1000 -2000 -100 -100 -2000 -200 -200 -4000 -3000 -300 10 -300 -4000 -400 -6000 -400 20 Microseconds/ 20 Microseconds/ 2 Microseconds/Division 2 Microseconds/Division Division Division 10 Before After Before After 10 Let-Through Voltages (L-N) Description AEGIS-HW (L-N Mode) 10 Category A ringwave (600V, 200A) 6V 10 Category B ringwave (600V, 500A) 9.6V Category B combination (impulse) wave (6000V, 300A) 70V 10 (206V, dynamic at 90°) Notes 10 230V applies to 220 and 240 volt applications. Model rated at 15 amperes UL/CSA = 16 amperes CE. 10 Based on ANSI/IEEE C62.41, 1991 and C62.45, 1992. Static testing. 10
Distribution Products Catalog CA08101001E—July 2010 www.eaton.com 21 10.2 SPD, Power Conditioning, PF Capacitors and Harmonic Filters Surge Protective Devices (SPD)
10 CVX050/100A Contents Description Page 10 Product Overview ...... 6 SPD Series for Integration into Electrical 10 Distribution Equipment ...... 8 SPD Series for Mounting External to Electrical 10 Distribution Equipment ...... 12 CVL Surge Protective Device ...... 17 10 AEGIS Powerline Filters ...... 19 CVX050/100 10 Catalog Number Selection ...... 23 Technical Data and Specifications ...... 23 10 Dimensions ...... 24 10 Datacom ...... 25 10
10
10 CVX050/100 10 Product Description Application Description Features, Benefits Standards and Certifications With over two decades of Eaton’s CVX050 and CVX100 and Functions ● UL 1449 3rd Edition for 10 experience in the surge SPDs protect electronic ● Advanced surge path surge protective devices suppression industry and equipment from damaging technology for high fault ● CE marked extensive R&D initiatives, transients. These units are 10 current capacity, low ● Vibration tested IEC Eaton is considered a world suitable for medium and low impedance, high frequency 60255-21-1 and -2 10 leader in surge protective exposure level applications design device (SPD) manufacturing. that require cost-effective, ● Rugged NEMA 4X (IP65) All of Eaton’s products are high quality system enclosure 10 manufactured in an ISO protection including: ● Large diameter, thermally 9001:2000 and ISO 14001 ● protected metal oxide 10 certified facility. Residential/small business ● Light industrial varistors provide long life Eaton’s CVX050/100 models and fail-safe operation ● Light commercial 10 are rugged, cost-effective, ● LED monitoring of each ● Branch panel protection high-quality SPDs that feature phase 10 thermally protected MOVs ● Wide range of voltage that eliminate the failure applications from characteristics of standard 100 to 480 Vac 10 Metal-Oxide-Varistors. The ● 10-year free replacement TPMOV is a fail-safe device warranty 10 that monitors the status of the metal-oxide disk and Optional Features 10 connects itself from the power system when the disk ● Available flushmount for 10 is approaching breakdown. recessed installations The CVX050/100 is easy 10 to install adjacent or even internal to electrical 10 equipment. When installing an SPD in a retrofit environment, it is important to mount the 10 device as close to the electrical equipment as 10 possible. Keep the wiring (lead length) between the electrical 10 equipment and SPD as short as possible, and twist or wire 10 tie the conductors together to reduce the wire’s 10 impedance factor.
22 Distribution Products Catalog CA08101001E—July 2010 www.eaton.com SPD, Power Conditioning, PF Capacitors and Harmonic Filters 10.2 Surge Protective Devices (SPD)
Catalog Number Selection 10 CVX050/100 10 CVX - 10
Per Phase Peak Configuration and Voltage Ranges (Vac) 10 Surge Current 230L = Single-phase–200, 208, 220, 230, 240, 277 050 = 50 kA 240S = Split-phase–100/200, 110/220, 120/240 10 100 = 100 kA 208Y = Three-phase wye (star)–100/175, 110/190, 120/208, 127/220 480Y = Three-phase wye (star)–220/380, 230/400, 240/415, 277/480 240D = Three-phase delta–200, 208, 220, 230, 240 10 480D = Three-phase delta–380, 400, 415, 440, 480 10 Technical Data and Specifications 10 CVX050/100 Model Specifications 10 Description Specification kA per phase 50, 100 10 kA per mode 50 Protection modes Wye system: L-L, L-N, L-G and N-G/delta system: L-L, L-G split 10 Wye system voltages 100/175, 110/190, 120/208, 127/220, 220/380, 230/400, 240/415, 277/480 10 Delta system voltages 200, 208, 220, 230, 240, 380, 400, 415, 440, 480 Split-phase voltages 100/200, 110/220, 120/240 10 Single-phase voltages 200, 208, 220, 230, 240, 277 Weight 2.0 lbs (1.0 kg) 10 Operating temperature –13ºF (–25ºC) to + 140ºF (+60ºC) 10
CVX050/100 Let-Through Voltage Ratings 10 Voltage Protection Ratings 10 Model System Nominal System MCOV UL VPR , UL 1449-3 Type Configuration Voltage L-N L-G N-G L-L L-N L-G N-G L-L 10 CVX050 230L Single-phase, two-wire + ground 200, 208, 220, 230, 240, 277 320 640 320 — 1200 2000 1200 — 10 240S Split-phase, three-wire + ground 100/200, 110/220, 120/240 150 300 150 300 700 1200 800 1200 208Y Three-phase wye/star, four-wire + ground 100/175, 110/190, 120/208, 127/220 150 300 150 300 700 1200 800 1200 10 480Y Three-phase wye/star, four-wire + ground 220/380, 230/400, 240/415, 277/480 320 640 320 640 1200 2000 1200 2500 240D Three-phase delta, three-wire + ground 200, 208, 220, 230, 240 — 320 — 320 — 1200 — 2000 10 480D Three-phase delta, three-wire + ground 380, 400, 415, 440, 480 — 550 — 1100 — 1800 — 3000 10 CVX100 230L Single-phase, two-wire + ground 200, 208, 220, 230, 240, 277 320 320 320 — 1200 1200 1200 — 10 240S Split-phase, three-wire + ground 100/200, 110/220, 120/240 150 150 150 300 700 800 700 1200 208Y Three-phase wye/star, four-wire + ground 100/175, 110/190, 120/208, 127/220 150 150 150 300 600 700 700 1000 10 480Y Split-phase, three-wire + ground 100/200, 110/220, 120/240 320 320 320 640 1200 1200 1200 1800 10 240D Three-phase delta, three-wire + ground 200, 208, 220, 230, 240 — 320 — 320 1200 — — 1800 480D Three-phase delta, three-wire + ground 380, 400, 415, 440, 480 — 550 — 1100 1800 — — 3000 10 Notes U.S. voltages in bold. 10 CVX100 model only. Test environment: All tests performed with 6-inch lead length, positive polarity. Voltages are peak ±10%. 10 10 10
Distribution Products Catalog CA08101001E—July 2010 www.eaton.com 23 10.2 SPD, Power Conditioning, PF Capacitors and Harmonic Filters Surge Protective Devices (SPD)
Dimensions 10 Approximate Dimensions in Inches (mm) 10 CVX050/100 Standard Dimensions
10 5.60 (142.2) 10 4.72 (119.9) 0.75 Internally Threaded 10 4.17 (19.1) Conduit Fitting (105.9) 10 10 3.39 (86.1) 10 4.17 (105.9) 2.36 10 (59.9) 10 A A Mounting 1.12 Holes (28.4) 10 Under 3.53 Lid (4) (89.7) 10 10 10 Mounting Hole Ø 0.17 Shafts 10 (4.3) 10 SECTION A-A 10 10 10 10 10 10 10 10 10 10 10 10 10 10
24 Distribution Products Catalog CA08101001E—July 2010 www.eaton.com SPD, Power Conditioning, PF Capacitors and Harmonic Filters 10.2 Surge Protective Devices (SPD)
Datacom Products Contents 10 Description Page Product Overview...... 6 10 SPD Series for Integration into Electrical Distribution Equipment ...... 8 10 SPD Series for Mounting External to Electrical Distribution Equipment ...... 12 10 CVL Surge Protective Device ...... 17 AEGIS Powerline Filters ...... 19 10 CVX050/100 ...... 22 10 10 10 10
10
Datacom 10 Product Description Features and Benefits 10 Eaton’s Datacom surge Exceptional performance is protection products are achieved using three-stage 10 designed for all industries hybrid technology: and applications. The wide ● range of products offers Gas tubes for shunting 10 rugged surge protection in high energy convenient, easy-to-install ● Silicon avalanche 10 configurations. components for responsive, low 10 let-through voltages ● PTC resettable fuses for 10 mitigating fault current ● Our modular design 10 enables customers to protect complete facilities or individual loads. 10 Customers also save significant time and money 10 due to our unique plug-in components and 10 protection modules 10 10 10 10 10 10 10 10 10
Distribution Products Catalog CA08101001E—July 2010 www.eaton.com 25 10.3 SPD, Power Conditioning, PF Capacitors and Harmonic Filters Power Conditioning Products
10 Sag Ride Through (SRT) Contents Description Page 10 Sag Ride Through (SRT) Application Description ...... 27 10 Features, Benefits and Functions ...... 27 Catalog Number Selection ...... 28 10 Technical Data and Specifications ...... 29 Dimensions ...... 31 10 Electronic Voltage Regulator (EVR) ...... 32 10 10 10 10
10
10 Sag Ride Through (SRT) 10 Product Description Eaton’s sag ride through is Today’s industrial and large Depending on the proximity Regularity of Voltage Sags 10 the first of its kind. commercial electricity to the fault, which can be EPRI conducted a two-year customers are becoming hundreds of miles away, study of power quality levels The SRT power conditioner more sensitive to power the voltage during the sag 10 prevents expensive on distribution systems in the disturbances and are is typically 40%–90% of United States. A variation electrical downtime. The demanding better electric nominal utility voltage. The SRT represents Eaton’s event was recorded every 10 quality. However, the quality operation of circuit breakers, time the voltage dropped state-of-the-art solution to of power grids is not fuses and reclosers limits today’s power conditioning below 90% of the nominal. 10 significantly improving. most sags to less than The results are shown below. challenges. Customers still experience 15 cycles. 10 power quality problems A typical distribution system The Problem—Voltage Sags that affect plant operations Voltage sags are experienced customer experiences about and Brownouts and profitability. 10 to 20 times more 50 events per year when the 10 The ability of a plant to frequently than complete voltage drops below 90%, ride through voltage sags Deep, Single-Phase Sag outages. However, voltage and only about two events 10 can have a significant sags are equally disruptive per year when the voltage Input A Input A Input A impact on operations and to sensitive equipment. drops below 30% of nominal. competitiveness. In the 600 10 400 Voltage Sags The utility study concluded United States, voltage sags 200 that sags represented almost 0 cost billions of dollars in 1. Fault occurs on all of the events experienced -200 10 lost production, interruption, the transmission at a typical facility. -400 Generation or distribution damaged materials, retooling -600 system 10 and scrap. In addition, Events per Year End sags can cause: increased Users operating costs, the need Definition of Voltage Sag 10 Transmission 6 for product reworks, safety A voltage sag is a sudden, Distribution 10 hazards, equipment damage momentary decrease in 5 and/or failure, reduced supply voltage. It can last 2. Creates a sag 4 product quality, increased from a cycle to several Feeder event for all Breakers users on the 3 10 clean-up, additional labor seconds. Voltage sags are End system costs, increased scrap most often caused by faults User 2 10 material and costs associated on the electrical transmission 1 End User or distribution system. They 0 with investigations into – 70 50 5 the problem. can be caused by lightning – 10 2 1 – 40 10 – – 10 strikes, animal contact, 20 10 6 starting of large motors 10 or an internal fault within a customer’s facility. 10 10
26 Distribution Products Catalog CA08101001E—July 2010 www.eaton.com SPD, Power Conditioning, PF Capacitors and Harmonic Filters 10.3 Power Conditioning Products
Application Description Features, Benefits and Functions 10 Industries and Applications Sag Correction Using the SRT Continuous Regulation Affected by Sags The SRT is a high The Sag Ride Through is an 10 Key industries: Equipment or processes: performance, inverter- active voltage conditioner. based voltage conditioning This means it will constantly ● Semi-conductor ● Manufacturing process 10 device developed to provide respond to voltage sags and manufacturers controllers protection to sensitive loads swells in the +/–10% range ● ● 10 Communications Variable speed drives against commonly occurring with a regulated output in the ● Steel mills ● Robotics voltage sags. +/–1% range. The SRT can be ● Petroleum and chemical ● Motor conductor applied to the main service 10 The SRT monitors the processing ● entrance, at branch locations Telephone systems incoming supply voltage and ● or in front critical loads. The 10 Health care ● HID lighting when it deviates from the SRT provides an outstanding ● Paper mills ● HVAC controls nominal voltage level, the return on investment. It 10 ● Automotives ● Medical equipment SRT achieves voltage delivers operation productivity ● conditioning by injecting the Textile ● Computers that is just not possible with appropriate correction voltage 10 ● Printing traditional tap switching or in series with the power ferroresonant technologies. ● Plastics supply. The SRT provides an The SRT consists of a voltage 10 ● Other manufacturing extremely fast reaction time source inverter, bypass circuit and subcycle response to sag and an injection transformer 10 events that would otherwise Block Diagram of the SRT Active Voltage Conditioner connected in series between cause loads to drop out. the incoming utility supply 10 The SRT is designed for low and the load, as shown in voltage systems (600 to 208, the figure below. For the 10 three-phase) and is also standard sag correcting offered in medium voltage model, the injection 3-Phase Compensating applications from 25 kVA transformer consists of a 10 Voltage boost component. The SRT Secondary to 4 MVA. Installation is 3-Phase 3-Phase simple and the SRT monitors the incoming supply 10 Utility Injection Load provides customers with voltage and when it deviates Supply Distribution Primary Transformer Voltage from the nominal voltage Transformer a new solution to improve 10 productivity and reduce level the SRT inserts an appropriate compensating Bypass Circuit downtime for sag related 10 SRT Input problems. voltage using the IGBT SRT Output inverter and series injection The SRT meets the transformer. Energy is 10 Voltage Source stringent requirements sourced from the supply Inverter of the Semi-F47 standard; during this time. This 10 a key requirement for SAG regulates the load voltage correction in the semi- to its nominal value, conductor industry. thus eliminating voltage 10 disturbances from the utility ● Complete correction supply affecting the load. 10 of single-phase voltage sags down to 63% for 30 seconds 10 ● Partial correction of three- phase sags down to 50% 10 for 30 seconds ● Correction of utility voltage 10 unbalance (from network side of transformer) 10 ● Attenuation of voltage flicker 10 10 10 10 10 10
Distribution Products Catalog CA08101001E—July 2010 www.eaton.com 27 10.3 SPD, Power Conditioning, PF Capacitors and Harmonic Filters Power Conditioning Products
10 Catalog Number Selection 10 SRT2 10 SRT2 1200 480 A A – TC
10 Load kVA, 30% Load kVA, 40% Options 0200 0600 1500 0150 0600 1500 Voltage Frequency Correction Blank = None 10 0225 0800 2000 0225 0750 1800 208 A = 60 Hz A = 40% (+10/–40%) TC = Terminal cabinet 0300 1000 2400 0300 0900 480 B = 50 Hz B = 30% (+10/–30%) 0400 1200 0450 1200 600 C = 15% (+10/–15%) 10 Three-phase/three-wire 10 SRT (30% Correction) SRTS (40% Correction) 10 SRT 0075 480 A A SRT 0050 480 A A 10
Model Bypass Model Bypass 10 Load Voltage Frequency A = No Load Voltage Frequency A = No kVA 208 A = 60 Hz B = Yes kVA 208 A = 60 Hz B = Yes 10 0025 480 B = 50 Hz 0017 480 B = 50 Hz 0050 600 0033 600 0075 Three-phase/ 0050 Three-phase/ 10 three-wire three-wire
Notes 10 For 50% Hz international applications, consult factory. For 15% correction, consult factory. 10 Optional mechanical bypass, refer to factory for details. For 50 Hz international applications, consult factory. 10 Terminal cabinet required on all units 200 kVA and larger except when a bypass is required. 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10
28 Distribution Products Catalog CA08101001E—July 2010 www.eaton.com SPD, Power Conditioning, PF Capacitors and Harmonic Filters 10.3 Power Conditioning Products
Technical Data and Specifications 10 SRT Specifications 10 Description Specifications Load Capacity 10 Capacity (kVA) 25 kVA to 50 MVA (as specified per model) Displacement power factor of connected load 0–1, leading or lagging 10 Crest factor for rated kVA 2.0 at 100% of rated load for continuous operation (including up to 10% voltage correction) Overload—30 seconds 150% with up to 10% of voltage correction 10 Input Supply 10 Nominal supply voltage 208/480/600V, 60 Hz three-phase, three-wire plus ground (higher system voltages supplied to requirement up to 36 kV) Maximum supply voltage 110% of nominal supply voltage 10 Minimum three-phase supply voltage Running 50% of nominal supply voltage 10