046-Paraffin Wax Instruction Sheet-V2.Ai

Total Page：16

File Type：pdf, Size：1020Kb

046-Paraffin Wax Instruction Sheet-V2.Ai

USING PARAFFIN WAX FOR CANDLE MAKING. GOOD RULES TO FOLLOW... Paraffin Wax has many practical and hobby uses! This instruction sheet focuses on candle making for pillar, votive & container candles. This wax is not formulated for spa/therapy use on body parts. 1. Place our Paraffin Wax into a pouring pitcher that is itself placed in 1lb (450g) Paraffin Bars a pan of water (essentially, a double-boiler setup). Use a thermometer to monitor the wax’s temperature, and heat it to a liquid state (85°C / 185°F is a good target temperature). 2. If you’re going to add colouring to your Paraffin Wax, do so at about 80°C / 175°F. 3. Once liquified, stir the Paraffin Wax for 4-5 minutes, to ensure evenness between the wax and any additives / colouring you might be using. 4. If you’re going to add fragrance oils to your Paraffin Wax, do so just before pouring. Once added, stir the Paraffin Wax again. (This will maximize the fragrance effect.) 5. For pouring, turn your heat down and let the wax cool (71°C/160°F). Pouring into a preheated container/mold is best. 3lb (1.36kg) Paraffin Granules 6. Pour at a consistent temperature - wax that is too cool when poured may create air bubbles; wax that is too hot may shrink undesirably. For best results, pour the wax just above its melting point. Save about 20% of your wax from your original pour, for top-ups. After pouring, you may have to top up your candle containers because wax will typically shrink after it cools down. If desired, do a re-pour of additional wax into your candle’s container to top it up and level it out. Let the wax completely solidify first. NOTES FOR SAFE USE 7lb (3.2kg) Paraffin Granules 1. Paraffin Wax is excellent for candle-making. Do not heat or melt the wax over an open flame or in a microwave. 2. Do not overheat - like most wax, Paraffin Wax is flammable. 3. Remove wax pieces/granules from their box or pail before melting. Never melt the wax while still inside its container. 4. Always follow the operating instructions of your wax warmer if you’re using one. Paraffin Wax is usable in all warmers. 5. Paraffin Wax is a food grade wax, and is safe for canning. It is FDA approved: 21 CFR 172.886 Percheron Plastic Inc. 789 O’Brien Drive +1.800.780.3609 Home of Canadian Paraffin Wax Peterborough, ON, K9J 6X7 sales @ percheronplastic.com 046-V.2-2020 percheronplastic.com.

Copy Link

Recommended publications

Packaging Food and Dairy Products for Extended Shelf-Life Active Packaging: Films and Coatings for Ex- 426 Shelf Life, ESL Milk and Case-Ready Meat
Packaging Food and Dairy Products for Extended Shelf-Life Active packaging: Films and coatings for ex- 426 shelf life, ESL milk and case-ready meat. In the last two years, there tended shelf life. Paul Dawson*, Clemson University. has been substantial growth in extended shelf life milk packaged in sin- gle serve PET or HDPE containers. The combination of ESL processing Shelf life encompasses both safety and quality of food. Safety and and a plastic container results in an extended shelf life of 60 to 90 days, spoilage-related changes in food occur by three modes of action; bi- and at the same time provides consumers with the attributes they are ological (bacterial/enzymatic), chemical (autoxidation/pigments), and demanding from the package: convenience, portability, and resealabil- physical. Active packaging may intervene in the deteriorative reactions ity. The second example of how polymers are part of the solution to by; altering the package film permeability, selectively absorbing food extend shelf life is focused on case-ready beef. Here, a combination of components or releasing compounds to the food. The focus of this re- a polymer with the appropriate gas barrier and a modified atmosphere port will consider research covering impregnated packaging films that re- allows beef to retain its bright red color longer, extending its shelf life. lease compounds to extend shelf life. The addition of shelf life extending Plastics are increasingly used in food packaging and will be part of the compounds to packaging films rather than directly to food can be used future of extended shelf life products. to provide continued inhibition for product stabilization.
[Show full text]
Phase Change Materials Based on Polyethylene, Paraffin Wax and Wood Flour
PHASE CHANGE MATERIALS BASED ON POLYETHYLENE, PARAFFIN WAX AND WOOD FLOUR by MFISO EMMANUEL MNGOMEZULU (B.Sc. Hons.) 2002121057 Submitted in accordance with the requirements for the degree MASTER OF SCIENCE (M.Sc.) Department of Chemistry Faculty of Natural and Agricultural Sciences at the UNIVERITY OF THE FREE STATE (QWAQWA CAMPUS) SUPERVISOR: PROF A.S. LUYT CO-SUPERVISOR: DR I. KRUPA November 2009 DECLARATION I declare that the dissertation hereby submitted by me for the Masters of Science degree at the University of the Free State is my own independent work and has not previously been submitted by me at another university/faculty. I furthermore, cede copyright of the dissertation in favour of the University of the Free State. ________________ __________________ Mngomezulu M.E. (Mr) Luyt A.S. (Prof) i DEDICATIONS Kubazali bami abathandekayo: UBaba Vusimuzi Josiah Mngomezulu noMama Mafahatsi Jerminah Mngomezulu. Ngiswele imilomo eyizinkulungwane ngothando nemfundiso yenu kimi kusukela ngizalwa kuzekube kusekugcineni. Ngibonga abazali benu (Ogogo nomkhulu bami-Umkhulu Christmas Meshaek Mbuti Mngomezulu (odukile) nogogo Teboho Linah Mngomezulu, kanye nomkhulu Lehlohonolo Petrus Monareng (osekwelamathongo) nogogo Kukkie Violet Monareng). Anginalo iGolide neSiliva ukunibonga ngoba ningenze umuntu ebantwini. Ngakho ngiyakunibonga ngokuphila impilo ehlanzekile phambi kukaMvelinqangi naphambi kwenu. Thokozani niphile boMfiso nani boSebei abahle!!! ii ABSTRACT Phase change material (PCM) composites based on high-density polyethylene (HDPE) with soft (M3) and hard (H1) Fischer-Tropsch paraffin waxes and alkali-treated wood flour (WF) were investigated in this study. Both the blends and composites were prepared using a melt- mixing method with a Brabender-Plastograph. SEM, DSC, TGA, DMA, tensile testing and water absorption were used to characterize the structure and properties of the blends and composites.
[Show full text]
Paraffin Wax Dispenser Instruction Book
PARAFFIN WAX DISPENSER MH8523B, MH8523Bx1. INSTRUCTION BOOK Page 1 of 20 M6880 issue 4.1 Please take your time to read this Instruction book in order to understand the safe and correct use of your new Electrothermal product. It is recommended the Responsible Body for use of this equipment reads this Instruction book and ensures the user(s) are suitably trained in its operation. CONTENTS Section 1 Introduction Page 3 Section 2 Symbols and using this Instruction book Page 4 Section 3 Safety Information. Page 5 Section 4 Unpacking and contents Page 7 Section 5 Installation Page 8 Section 6 Environmental Protection. Page 9 Section 7 Product Operation. Page 10 Section 8 Technical Specification. Page 12 Section 9 Maintenance Page 13 Section 10 Customer Support Page 16 Section 11 Spares and Accessories Page 18 Section 12 Notes Page 19 Section 13 EC declaration of Conformity Page 20 Appendix A Decontamination Certificate. Page 17 © The copyright of this Instruction book is the property of Electrothermal. This instruction book is supplied by Electrothermal on the express understanding that it is to be used solely for the purpose for which it is supplied. It may not be copied, used or disclosed to others in whole or part for any purpose except as authorised in writing by Electrothermal. Electrothermal reserve the right to alter, change or modify this instruction book with out prior notification. In the interest of continued development Electrothermal reserve the right to alter or modify the design and /or assembly process of their products without prior notification. This product is manufactured in Great Britian by Electrothermal Engineering Limited.
[Show full text]
Physiotherapy Department Wax Therapy
Patient Information Physiotherapy Department Wax Therapy What is wax therapy? Paraffin wax bath therapy is an application of molten paraffin wax and mineral oil to parts of the body. The combination of paraffin and mineral oil has a low specific heat which enhances the patient’s ability to tolerate heat better than from water of the same temperature. It is one of the most effective ways of applying heat to improve mobility by heating connective tissues. Wax therapy is mainly used on your hands in a hospital setting. Wax therapy is used to alleviate: Pain and stiffness associated with Osteoarthritis and Rheumatoid Arthritis Fibromyalgia Eczema (a dry skin disorder) Joint stiffness and muscle soreness from a variety of causes, such as following fractures, some minor surgical conditions, ligament sprains and strains What are the benefits of wax therapy? Paraffin wax acts as a form of heat therapy and can help improve circulation, relax muscles and reduce stiffness in the joints. It can also help soften skin and may help reduce swelling. Are there side effects? Paraffin wax is tested in a lab to make sure it’s safe and hygienic to use on the body. It’s completely natural and has a low melting point, which means Patient Information it can be easily applied to the skin at a temperature low enough not to cause burns or blisters. However, if you have very sensitive skin, paraffin wax may cause heat rash. Heat rash results in small red bumps on the skin that can be itchy and uncomfortable. If you have a chemical sensitivity, you may develop minor swelling or breakouts from the wax treatment.
[Show full text]
Extraction-Based Recovery of RDX from Obsolete Composition B
G Model JIEC 3540 1–5 Journal of Industrial and Engineering Chemistry xxx (2017) xxx–xxx Contents lists available at ScienceDirect Journal of Industrial and Engineering Chemistry journal homepage: www.elsevier.com/locate/jiec 1 Extraction-based recovery of RDX from obsolete Composition B 2 Q1 a a a a, b Hyewon Kang , Hyejoo Kim , Chang-Ha Lee , Ik-Sung Ahn *, Keun Deuk Lee 3 a Department of Chemical and Biomolecular Engineering, Yonsei University, Seoul 120-749, South Korea 4 b Agency for Defense Development, Daejeon 305-600, South Korea A R T I C L E I N F O A B S T R A C T Article history: Received 3 November 2016 Recovery of explosives from obsolete ammunition has been considered an eco-friendly alternative to Received in revised form 20 July 2017 conventional dumping or detonation disposal methods Composition B, made of 2,4,6-trinitrotoluene Accepted 26 July 2017 (TNT), hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX), and paraffin wax, has been used as the main Available online xxx explosive filling in various munitions. It was selected as a model explosive for this study. TNT was extracted from Composition B by exploiting the different solubilities of TNT and RDX in acetonitrile. After Keywords: removing paraffin wax by hexane washing, RDX was recovered from unused Composition B with a purity Composition B higher than 99% and a yield of 84%. Recovery © 2017 Published by Elsevier B.V. on behalf of The Korean Society of Industrial and Engineering RDX Chemistry. Extraction Demilitarization 5 29 Introduction destroyed using the following techniques: dumping at sea, outdoor 30 burning, open detonation, and detonation in a mine tunnel [9,10].
[Show full text]
Impact of Polymer Binders on the Structure of Highly Filled Zirconia Feedstocks
polymers Article Impact of Polymer Binders on the Structure of Highly Filled Zirconia Feedstocks Claire Delaroa 1,2, René Fulchiron 1 , Eric Lintingre 2, Zoé Buniazet 2 and Philippe Cassagnau 1,* 1 Ingénierie des Matériaux Polymères, Univ Lyon, Université Lyon 1, CNRS UMR 5223, 15 Boulevard Latarjet, 69622 Villeurbanne CEDEX, France; [email protected] (C.D.); [email protected] (R.F.) 2 Saint-Gobain CREE, Grains et Poudres, 550 Avenue Alphonse Jauffret, BP 20224, 84306 Cavaillon, France; [email protected] (E.L.); [email protected] (Z.B.) * Correspondence: [email protected] Received: 7 September 2020; Accepted: 28 September 2020; Published: 29 September 2020 Abstract: The impact of polypropylene and high-density polyethylene backbone binders on the structure of organic matrix, feedstock, and ceramic parts is investigated in terms of morphology in this paper. The miscibility of wax with polyethylene and polypropylene is investigated in the molten state via a rheological study, revealing wax full miscibility with high-density polyethylene and restricted miscibility with polypropylene. Mercury porosimetry measurements realized after wax extraction allow the characterization of wax dispersion in both neat organic blends and zirconia filled feedstocks. Miscibility differences in the molten state highly impact wax dispersion in backbone polymers after cooling: wax is preferentially located in polyethylene phase, while it is easily segregated from polypropylene phase, leading to the creation of large cracks during solvent debinding. The use of a polyethylene/polypropylene ratio higher than 70/30 hinders wax segregation and favors its homogeneous dispersion in organic binder. As zirconia is added to organic blends containing polyethylene, polypropylene, and wax, the pore size distribution created by wax extraction is shifted towards smaller pores.
[Show full text]
The Modified Research of Paraffin Material for Machining
2018 7th International Conference on Advanced Materials and Computer Science (ICAMCS 2018) The Modified Research of Paraffin Material for Machining Jin Hua, Minghua Chenb Aviation Maintenance NCO Academy, Xinyang, 464000, China [email protected], [email protected] Keywords: paraffin wax system; stearic acid; toughening agent A; polyethylene; NC machining. Abstract: The materials used in NC machine tools are usually steel, which is of high hardness. The influence factors for paraffin wax system performance are studied, which include the effects of stearic acid, toughening agent A, polyethylene and cooling-down methods. The material is prepared according to a certain proportion of the material by modification, which can be used in the mechanical processing of paraffin composite system to replace the material used in CNC processing. The practical application shows that the paraffin compound system can meet the requirements of NC machining and achieve the goal of energy saving and consumption, which is very effective. 1. Introduction Machining of material is usually using rolled steel. Because of its high hardness and great intensity, beginners easily damage equipment and tools by wrong operation during the process of practice [1-2]. Especially in numerical control machine tools, it always causes large amount of waste materials or even causes some accidents due to programming error and tool error. From the material saving and safety point of view, the paraffin can be used as training materials instead of rolled steel [3]. There are many advantages using paraffin, such as low hardness, low cost, recyclable used repeatedly, and so on. So it does not need cutting fluid in machining process and does not damage the cutter.
[Show full text]
Celebrating the Rich History of Waxes Bladel, the Netherlands What’S Inside: Watertown, Connecticut, Usa
CELEBRATING THE RICH HISTORY OF WAXES BLADEL, THE NETHERLANDS WHAT’S INSIDE: WATERTOWN, CONNECTICUT, USA 2-3 – HERITAGE 4-5 – INNOVATION 6-7 – WORLD RESOURCES 8-9 – NATURAL/ORGANIC 10-11 – SILICONYL WAXES 12-13 – CUSTOM BLENDS 14-15 – EMULSIFYING WAXES 16-17 – KESTER WAXES 18-19 – MILKS 20-41 – WAX SPECIFICATIONS 42 – WAX PROPERTIES KOSTER WAX FACT: Koster Keunen was founded in the Netherlands and is world renowned for supplying quality waxes. 1852 OUR HISTORY OF TRADITION AND INNOVATION Founded in 1852 as a family business, Koster Keunen has evolved into the world’s leading processor, refiner and marketer of natural waxes. From the early days of sun bleaching beeswax for the candle industry, we now specialize in processing and formulating quality waxes for cosmetics, pharmaceutical, food, coatings, and various other technical industries worldwide. For over 150 years we have sought perfection, constantly introducing new and innovative processes and waxes, while investing in experienced, knowledgeable people and the best equipment to help meet this goal. As a family business we believe very strongly in the need for developing 3 superior quality products, and supporting our customers with excellent service, throughout the formulation and marketing processes. From our two facilities, in the USA and Holland, we offer a huge range of natural waxes, synthetic waxes and wax derivatives, enabling our customers to produce thousands of products that look, feel and work superbly KOSTERKEUNEN.COM / 1 860.945.3333 KOSTER WAX FACT: Koster Keunen was the first natural wax company to manufacture waxes using a Sandvik Pastillator, starting in 1988. 1852 UNIQUELY KOSTER KEUNEN Our greatest strength is the experience and scientific expertise we have fostered for the development of new and innovative products.
[Show full text]
Paraffin Wax
Material Safety Data Sheet (MSDS) - Paraffin Wax 1. Chemical Product and Company Identification Product Name : Paraffin Wax Catalog Codes : SLW1045 CAS# : 8002-74-2 or 64742-43-4 RTECS : RV0350000 TSCA : TSCA 8(b) inventory: Wax (Paraffin) CI# : Not available. Synonym : Wax; White Cake Chemical Name : Paraffin Chemical Formula : Not available. COMPANY IDENTIFICATION Supplier: Pon Pure Chemicals Group CHENNAI, TAMILNADU, INDIA 24 Hour Health Emergency (91) 8939878447 (91) 9444038694 Transportation Emergency Phone (91) 8939768680 Company Name Place EMERGENCY TELEPHONE NUMBER Pon Pure Chemicals Group India Day Emergency – 044-26161803-26161809 2. Composition and Information on Ingredients Composition: Name CAS # % by Weight Wax ( Paraffin) Beads 8002-74-2 or 64742-43-4 100 Toxicological Data on Ingredients: Not applicable. 3. Hazards Identification Potential Acute Health Effects: Slightly hazardous in case of skin contact (irritant), of eye contact (irritant), of ingestion, of inhalation. Potential Chronic Health Effects: CARCINOGENIC EFFECTS : Not available. MUTAGENIC EFFECTS : Not available. TERATOGENIC EFFECTS : Not available. DEVELOPMENTAL TOXICITY : Not available. Repeated or prolonged exposure is not known to aggravate medical condition. Page 1 of 6 MSDS - Paraffin Wax 4.First Aid Measures Eye Contact: Check for and remove any contact lenses. In case of contact, immediately flush eyes with plenty of water for at least 15 minutes. Get medical attention if irritation occurs. Skin Contact: Wash with soap and water. Cover the irritated skin with an emollient. Get medical attention if irritation develops. Serious Skin Contact: Not available. Inhalation: If inhaled, remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get medical attention.
[Show full text]
Sustainable Packaging on the Shelf Today - Paramelt Turns to Nature for the Easy Answer
Sustainable packaging on the shelf today - Paramelt turns to nature for the easy answer Whether it comes to repellent properties to keep leaves clean or barrier requirements to prevent moisture loss in harsh environments, nature has a simple answer - Wax. Today thousands of tons of paper based, barrier packaging is being commercially produced every year based on effective and sustainable vegetable wax technology. For over a century paraffin wax has been used in a similar way to provide release and barrier properties to paper and board. Over recent years the industry has been working hard to harness a more sustainable solution based on renewably sourced vegetable fats. By combining paper produced from responsibly managed forests with sustainably sourced fats it is now possible to produce a fully efficient packaging material based on over 90% renewable bio materials. In a European setting all the talk today is about a shift towards a sustainable, bio-based economy. In the packaging industry this is being translated into many complex and expensive structures, combining bio- plastics with paper and other cellulosic materials. For many existing applications however bio sourced wax can easily be overlooked as it seems just too easy… These products are commercially available and provide excellent barrier and release properties. They can be run on existing equipment and can meet all renewability and ‘end of life’ requirements. Despite its long history, the use of wax paper today has been confined mainly to a small number of niche applications like confectionery packaging, cheese and meat wrappings; since it has been largely superseded by plastic films, extrusion coating or laminated structures.
[Show full text]
Well Stimulation Using Scrap Tires Final Report
Well Stimulation Using Scrap Tires – Final Report DOE Award Number: 4188‐RJLG‐DOE‐2098 RJ Lee Group Well Stimulation Using Scrap Tires Final Report RJ Lee Group Project Number GSH007011 Report Issue Date: December 2011 Principal Authors: Michael Silsbee PhD, Alan Levine PhD, Mark Sparrow RJ Lee Group, Inc. 350 Hochberg Rd. Monroeville, PA 15146 DOE Award Number: 4188‐RJLG‐DOE‐2098 March 2012 i Well Stimulation Using Scrap Tires – Final Report DOE Award Number: 4188‐RJLG‐DOE‐2098 RJ Lee Group Disclaimer This report was prepared as an account of work sponsored by an agency of the United States Government. Neither the United States Government nor any agency thereof, nor any of their employees, makes any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product, or process disclosed, or represents that its use would not infringe privately owned rights. Reference herein to any specific commercial product, process, or service by trade name, trademark, manufacturer or otherwise does not necessarily constitute or imply its endorsement, recommendation, or favoring by the United States Government or agency thereof. The views and opinions of authors expressed herein do not necessarily state or reflect those of the United States Government or any agency thereof. Abstract The following is the final report summarizing the results of the testing performed under grant 41880‐RJLG‐DOE‐2098. Three wells were located for field testing. One gas well is near Chautauqua, New York and two oil wells are near Yawkey, West Virginia. Samples of paraffin and oil from each of the sites have been characterized and evaluated for dissolution/suspension in DESolv™ at various temperatures.
[Show full text]
In-Situ Electrochemical Remediation of Underwater Unexploded Ordinance
FINAL REPORT In-Situ Electrochemical Remediation of Underwater Unexploded Ordinance SERDP Project MR18-1466 NOVEMBER 2018 Kyoo Jo U.S. Army Corps of Engineers, ERDC-CERL Distribution Statement A Page Intentionally Left Blank This report was prepared under contract to the Department of Defense Strategic Environmental Research and Development Program (SERDP). The publication of this report does not indicate endorsement by the Department of Defense, nor should the contents be construed as reflecting the official policy or position of the Department of Defense. Reference herein to any specific commercial product, process, or service by trade name, trademark, manufacturer, or otherwise, does not necessarily constitute or imply its endorsement, recommendation, or favoring by the Department of Defense. Page Intentionally Left Blank Form Approved REPORT DOCUMENTATION PAGE OMB No. 0704-0188 The public reporting burden for this collection of information is estimated to average 1 hour per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing the burden, to Department of Defense, Washington Headquarters Services, Directorate for Information Operations and Reports (0704-0188), 1215 Jefferson Davis Highway, Suite 1204, Arlington, VA 22202-4302. Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number. PLEASE DO NOT RETURN YOUR FORM TO THE ABOVE ADDRESS.
[Show full text]