Mini Bag Have Fun with KOKKA Fabric!

Total Page：16

File Type：pdf, Size：1020Kb

produced by Mini Bag have fun with KOKKA fabric! The craft projects and works featured in kokka-fabric.com are strictly for personal use and enjoyment. Please refrain from selling handmade items using the same exact design (including the pieces Design & work: Kokka Fabric made in diﬀerent fabrics) featured in kokka-fabric.com. Instructions Size： about 16cm (l) x about 30cm (w) about 9cm (d) ※not including the handle 1. Attach the fusible interfacing to the outer main part, 6. Create a tuck on the main part and gusset respectively. outer gusset and outer handle. 2. With the front sides facing each other, 3㎝ Center Center sew the gusset at the bottom side. 【Main part】 Sew with 1cm seam Materials Outer gusset Lining main part Outer gusset Outer main part 4㎝ □ Outer fabric: 50cm x 110cm or wider (reverse side) (front side) (reverse side) (front side) □ Lining fabric: 40cm x 110cm or wider Press the seam open Magnetic button □ Fusible interfacing: 50cm x 90cm or wider *Repeat the same process for the lining fabric. Magnetic button inside □ Magnetic button: 1 pair (15mm diameter) 【Gusset】 2㎝ 3. With the front sides facing each other, Attach the magnetic button Fabric shown for this sample: P37400-400 (B) sew together the main part and gusset. and stich like letter L. Outer Outer gusset Baste for 5cm Outer gusset main part (reverse side) Outer main part (reverse side) (front side) (front side) Sew with 1cm seam Outer gusset Pattern (front side) 7. With the front sides facing All measurements are in centimeters (cm.) Numbers in 【】 denote seam allowance. each other, sew together the handles. Add 1cm seam unless otherwise stated. *Repeat the same process for the lining fabric. Sew up to hereHandle (reverse side) *side with interfacing Sew up to here 5 4. With the front sides facing outside, baste together side with interfacing 5 5 the outer and lining fabrics at the top opening. Sew up to here Sew up to here Sew up to here Sew at 0.5cm from the top edge. Handle (front side) Lining main part Sew up to here 【3】 Turn it inside out and fold the seam for 1cm. 9 (front side) Outer gusset 8. Sew together the gusset and handle to ﬁnish. 33 40 (front side) Place the handle in-between up to where the stitch Outer main part 13.5 Tuck here 10.5 【3】 line stops and sew together. (front side) Main part (front side) 0.5cm ８ 30 27.5 Handle 16 Center (front side) Gusset (front side) Sew up to here Sew up to here Main part 5. Double fold the top opening and run stitches. side with interfacing ８ 1.3cm wide stitch Bottom 5 5 Main part 0.2cm wide stitch 3 Outer fabric side (front side) Lining fabric Two pieces each Lining main part (front side) Gusset Handle 1.5 ㎝ 1.5 ㎝ Fusible interfacing Outer fabric Outer fabric Handle Outer main part Lining fabric Fusible interfacing (front side) Gusset (front side) (front side) Fusible interfacing Two pieces each Two pieces each.

Copy Link

Recommended publications

Historic Costuming Presented by Jill Harrison
Historic Southern Indiana Interpretation Workshop, March 2-4, 1998 Historic Costuming Presented By Jill Harrison IMPRESSIONS Each of us makes an impression before ever saying a word. We size up visitors all the time, anticipating behavior from their age, clothing, and demeanor. What do they think of interpreters, disguised as we are in the threads of another time? While stressing the importance of historically accurate costuming (outfits) and accoutrements for first- person interpreters, there are many reasons compromises are made - perhaps a tight budget or lack of skilled construction personnel. Items such as shoes and eyeglasses are usually a sticking point when assembling a truly accurate outfit. It has been suggested that when visitors spot inaccurate details, interpreter credibility is downgraded and visitors launch into a frame of mind to find other inaccuracies. This may be true of visitors who are historical reenactors, buffs, or other interpreters. Most visitors, though, lack the heightened awareness to recognize the difference between authentic period detailing and the less-than-perfect substitutions. But everyone will notice a wristwatch, sunglasses, or tennis shoes. We have a responsibility to the public not to misrepresent the past; otherwise we are not preserving history but instead creating our own fiction and calling it the truth. Realistically, the appearance of the interpreter, our information base, our techniques, and our environment all affect the first-person experience. Historically accurate costuming perfection is laudable and reinforces academic credence. The minute details can be a springboard to important educational concepts; but the outfit is not the linchpin on which successful interpretation hangs.
[Show full text]
CO Guide to Judging Clothing
Colorado 4-H Guide for Clothing Judges Standards of Quality Clothing Construction Introduction One of our basic tasks in evaluating or judging is to be able to recognize and identify the standards that give a garment a finished, professional look. There are many techniques that can be used to accomplish the same end product. Each of us has techniques that we like and techniques that we dislike. In an objective evaluation it is essential to play down our personal preferences and to build upon identified and accepted standards. In general, there are some standards that apply to almost all techniques. Almost all construction techniques should result in an area, finish or detail that is: • Inconspicuous o Flat and smooth o Free from bulk o Stitching a uniform distance from an edge or fold • Functional • Durable –stitching uniform and secure Specific standards that can be expected in good construction are listed on the following pages. They are organized by techniques and/or areas, and the techniques are presented in alphabetical order. Overall Appearance Be objective when considering the overall appearance and appeal of a garment. It may be helpful to think about there being at least one especially pleasing feature about this garment, reflecting the many hours of though, effort and creativity that went into its construction. It may be the design, fabric, use of unusual technique or detail. Particularly neat and well-done machine or handstitching, etc. o Overall neatness and cleanliness o Plaids, stripes, checks and other designs matched at seams o Fabric with a direction in design or nap issued in garment in one direction unless garment design requires variation.
[Show full text]
Design Iterations Through Fusion of Additive and Subtractive Design
DESIGN ITERATIONS THROUGH FUSION OF ADDITIVE AND SUBTRACTIVE DESIGN A thesis submitted to the College of the Arts of Kent State University in partial fulfillment of the requirements for the degree of Master of Arts by Gordon Stumpo May 2016 i Thesis written by Gordon Stumpo B.A., Washington State University, 2014 M.A., Kent State University, 2016 Approved by Vince Quevedo, Thesis Supervisor Brian Peters, Committee Member Margarita Benitez, Committee Member Dr. Catherine Amoroso Leslie, Graduate Studies Coordinator, The Fashion School Dr. Linda Hoeptner Poling, Graduate Studies Coordinator, The School of Art Mr. J.R. Campbell, Director, The Fashion School Dr. Christine Havice, Director, The School of Art Dr. John Crawford-Spinelli, Dean, College of the Arts ii TABLE OF CONTENTS Page LIST OF FIGURES ……………………………………………………………………………………….……….…….….vi LIST OF TABLES………………………………………………………………………………………...……….………..xi ACKNOWLEDGMENTS……………………………………………………………………………...………..………..xii CHAPTER I. INTRODUCTION…………………………………………………………………………………………..………….13 Concept……………………………………………………………………………………...................................13 Design Framework…………………………………………………………………………………………..…13 Surface and Structure Frameworks…………………………………………………………….….……14 Additive Design…………………………………………………………………………………………..…..….18 Subtractive Design……………………………………………………….……………………………....….…18 Tension…………….……………………………………………………………………………….…………..…..18 Price Point…………….…………………………….………………………………………………………...…..19 Personal Skills & Background…………….……………………………………………………….…..…..19 Problem Statement &
[Show full text]
LAPTOP SHOULDER BAG by Jackie Robinson, Animas Quilts - 2017
LAPTOP SHOULDER BAG by Jackie Robinson, Animas Quilts - 2017 Hydrangea Embroidery - digitized by OESD adapted from Hydrangea fabric by Jackie Robinson & Benartex LLC Outer Fabric - 7/8 yd Fusible Woven Interfacing - 1-3/4 yds if 40” wide or 3-1/2 yds if 20” wide Pellon Fleece - 1/2 yd Lining Fabric - 1/2 yd Medium weight Tear-Away, preferably Ultra Clean & Tear from OESD OESD Perfect Press Cloth Begin by measuring your laptop – width, height, and thickness. MacBook is: 14.125 x 9.75 x .75 I wanted a 6” flap, 2” of gusset (it has to include that on top, plus 9.75” height for the back = 17.75” x 14.125. Add 1” to both measurements (1/4” seams plus ease for the included batting) = 18.75” x 15.125” That’s the measurement I trimed to after embroidery. Therefore, begin with a 20” x 17” for the Back & Flap. It’s large, so fuse two layers of woven iron-on interfacing to the wrong side. Double interface all the pieces for strength, as well because of embroidery on the back as well as the flap. Use two layers of stabilizer also. Flap embroidery is 5” x 12”. At the Raw edge of the flap, mark center 2.5” + .5” = 1.125” + 4.125” up from the edge. Strap - Cut fabric at least 7” x 42” Two layers of Interfacing. Place leaves as desired, with two layers of stabilizer. After stitching, trim to 6-1/8” x 36” Cut front 10.75” x 15.125”. Double Interface.
[Show full text]
" 47.4% Attorney United States Patent Office
C, A, TURNER. ONE BUTTON UNION SUIT, 1,204,615. APPLICATION FLED NOW, 8, 1915. Patented Nov. 14, 1916. Fig.5 INVENTOR CHARLES A TL/FNER " 47.4% ATTORNEY UNITED STATES PATENT OFFICE. CHARLES A TURNER, OF UTICA, NEW YORK. oNE-BUTTON UNION-suIT. 1,204,615. Specification of Letters Patent. Paterated Nov. 14, f$91 6, , Application filed November 8, 1915. Serial No. 60,215. To all whom, it may concern; will eliminate, the double thickness of cloth Be it known that I, CHARLEs A. TURNER, at the crotch and obviate bulkiness in this a citizen of the United States, residing at section. However, if a double flap should Utica, in the county of Oneida and State of be found desirable, a small gusset can be New York, have invented certain new and readily attached to the corresponding edge 60 useful Improvements in One-Button Union of the garment to obtain this effect. Suits, of which the following is a specifica The flap or gusset, at the back of the gar tion, reference being had therein to the ac ment, is designed to be sewed to one edge of companying drawing. the slit or opening in the rear of the garment 0 My invention relates to one button union and to extend from the top or neckportion 65 suit, and I declare the following to be a full, to the crotch. The flap is cut with a greater clear, 'concise and exact description thereof width in that part opposite the lower per sufficient to enable anyone skilled in the art manent opening of the garment, whereby to to which it appertains to make and use the prevent the accidental opening of the same 15 same, reference being had to the accompany and the consequent exposition of the body.
[Show full text]
Princess & the Pea Pincushions
Princess & the Pea Pincushions Materials Required Granny Square Cushion Selvage String Cushion Fabric: Fabric: • 8 - 1 3/4” squares The Sweetest Thing • Variety of strips between 1” and 1 1/2” to blue & green prints make 4” x 6” string piece • 3 - 3 1/8” squares Bleached Denim solid • 1 - 4” x 6” rectangle Main Flower Blue • 1 - 4” x 6” rectangle Main Flower Blue • 1 - 2” x 21” strip Chevron Blue • 1 - 2” x 21” strip Chevron Blue Notions: Notions: • Sewing Machine • Sewing Machine • Fiberfill Stuffing • Fiberfill Stuffing • Vase Filler or Crushed Walnut Shells • Vase Filler or Crushed Walnut Shells • Hand sewing needle & thread • Hand sewing needle & thread • Scissors or rotary cutter • Scissors or rotary cutter 1 Granny Square Cushion 1. Cut Setting Triangles & Piece Top First, cut the three 3 1/8” squares into four quarter square triangles for setting, you will need 10 triangles for this project, two are leftover as scraps. Next arrange prints as shown and sew together in diagonal rows. Press seams in opposite directions, as shown, to make lining up points easy. Sew the rows together; then add the corner triangles to the piece. 2. Trim & Round Corners Trim the block so that 1/4” of the Bleached Denim fabric extends beyond the prints. Using a circle with a 1” diameter (I used a small spray bottle, but have provided a circle on the printer friendly pattern), draw a rounded corner on each corner triangle. Place the backing piece wrong sides together with the top and cut around the curves through both layers.
[Show full text]
Atlanta Attachment Company Innovative Technology for the Sewn Products Industry Worldwide © 2006 Atlanta Attachment Company
Atlanta Attachment Company Innovative Technology for the Sewn Products Industry Worldwide © 2006 Atlanta Attachment Company. All rights reserved. All materials contained herein are additionally protected by United States copyright law and may not be used, disclosed, reproduced, distributed, published or sold without the express written consent of Atlanta Attachment, which consent may be withheld in Atlanta Attachment’s sole discretion. You may not alter or remove any copyright, trademark or other notice from copies of these materials. Atlanta Attachment Company, AAC, Atlanta Parts Depot, “Sudden Service”, Sewing Automation, individually and when used in combination are registered trademarks of Atlanta Attachment Company. 05087011506 Welcome to Atlanta Attachment Company Innovative Technology for the Sewn Products Industry Worldwide Equipment Indexed by Category Category Page Corporate . iv - xi Binding . 0 - 3 Border - Foundation . 4 - 11 Border - Mattress . 12 - 25 Embroidery . 26 - 27 Flanging . 28 - 35 Handle Making . 36 - 37 Label . 38 - 41 Packaging . 42 - 43 Panel Cutting / Border Slitting . 44 - 45 Quilting . 46 - 49 Repair . 50 - 51 Ruffler . 52 - 67 Serger . 68 - 73 Springs . 74 - 81 Table . 82 - 83 Tape Edge . 84 - 93 Tufting . 94 - 95 Zipper . 96 - 101 Attachments & Folders . 102 - 103 Climate Control: Cool-Space . 104 Material Handling: ZRack, Mattress Trucks . 105 Plant Information & Control System: Satelite Plus . 106 Serial Bus Control System . 107 Parts . 108 ii Equipment Index by Model Number Model Description Page 1303 . Automatic Pocket Spring Production Line . 74 1304 . Wire Straightening Machine . 76 1305 . Pneumatic Border Bending Machine . 76 1309 . Spring Unbaler . 77 1312 . Automatic Decorative Border Workstation . 12 1313 & 1313M . Automatic Pocket Spring Machine . 78 1314 & 1314M .
[Show full text]
Gusset Plate Stress
GUSSET PLATE STRESS Gusset plates are used in steel buildings to connect bracing members to other structural members in the lateral force resisting system. Figure 1 shows a typical vertical bracing connection at a beam-to-column intersection. Gusset plates are also used to connect diagonal members to the chords and vertical members of trusses. Fig. 1. Vertical brace connection. A large number of research projects have been dedicated to the stresses in gusset plates. The research includes laboratory tests, finite element models, and theoretical studies. Many different failure modes have been identified, and design methods and specification requirements have been formulated based on the research. Design information for gusset plates can be found in the AISC Steel Construction Manual (AISC, 2005); however, the behavior of gusset plates is very complex and cannot be fully defined by the available design procedures. Engineering judgment is critical in the design process; therefore, it is important that engineers understand the background of the guidelines. This paper provides a design-based review of the available information on gusset plates and references for engineers who want to study the topic in-depth. Only the documents relevant to the evolution of the current design procedures are presented; however, additional references are listed in the bibliography. Other aspects of gusset plate design, such as stability, calculation if interface loads, and seismic design will be presented in future papers in this series. This paper is organized into three sections: Effective Width, Normal and Shear Stresses, and Combined Stresses. Connection Design for Steel Structures Chapter 7a, Page 1 of 21 Copyright © 2011 by Bo Dowswell EFFECTIVE WIDTH Existing Literature The first major experimental work on gusset plates was done by Wyss (1923).
[Show full text]
The Well Dress'd Peasant
TheThe WWellell DrDress’dess’d Peasant:Peasant: 1616thth CenturCenturyy FlemishFlemish WWorkingwomen’orkingwomen’ss ClothingClothing by Drea Leed The Well-Dress’d Peasant: 16th Century Flemish Workingwoman’s Dress By Drea Leed Costume & Dressmaker Press Trinidad, Colorado ACKNOWLEDGEMENTS The author and publisher wish to thank the following institutions for their help with the color images for the cover and interior color plates. Copyright for these images is retained by them, in accordance with international copyright laws. The images are used with permission. Cover A Marketwoman and Vegetable Stand, by Pieter Aertsen © Bildarchiv Preüssuscher Kulturbesitz Märkishes Ufer 16-18 D-10179 Berlin Germany Inside front cover Harvest Time by Pieter Aertsen and Plates 1, 3 The Pancake Bakery by Pieter Aertsen Harvest Time (A Vegetable and Fruit Stall) by Pieter Aertsen © Museum Boijmans van Beuningen Museumpark 18-20 CX Rotterdam The Netherlands Plate 2 (Centerfold) The Meal Scene (Allegorie van de onvoorzichtigheid) by Joachim Beuckelaer © Koninklijk Museum voor Schone Kunsten Plaatsnijderstraat2, B-2000 Antwerp Belgium © November 2000 by Drea Leed © November 2000 by Costume & Dressmaker Press Published by Costume & Dressmaker Press 606 West Baca Street Trinidad Colorado 81082 USA http://www.costumemag.com All rights reserved. No part of this work covered by the copyright hereon may be reproduced or used in any form or by any means - graphic, electronic or mechanical, including scanning, photocopying, recording, taping or information storage
[Show full text]
Metraflex Quality Products FLEXIBLE RUBBER PIPE
NON-METALLIC EXPANSION JOINTS APPLICATION & DESIGN GUIDE 2323 W. HUBBARD ST. • CHICAGO, IL 60612 • 312-738-3800 • FAX 312-738-0415 • http://www.metraflex.com How to Order Metraflex Non-Metallic Expansion Joints Please Provide the Following Information (as a minimum): 1. Size of Line: Nominal Pipe Diameter 2. System Application: Flowing Media, Requirements 3. Pressure or Vacuum: Internal, External 4. Temperature: Operating, Ambient 5. Movement: Direction, Amount 6. Need for Control Units: Based on System Anchoring 7. End Fittings: ANSI, DIN, British Standard, Metric, etc. This guide provides additional information on the details of choosing a joint for a given application. However, with the above information our engineers can choose a joint right for your needs. Metraflex has been supplying industry with quality piping products for over 40 years. Our reputation for superior products and technical support sets us apart from our competition. In addition to non-metallic expansion joints, Metraflex is a supplier of metallic expansion joints, braided hose, expansion loops, and other specialty piping products using bellows technologies. For more information or to order, Contact us at: (312) 738-3800 (312) 738-0415 Fax or contact the representative in your area - see back cover. Page 1 Non-Metallic Expansion Joints Elastomer (rubber) and Teflon® expansion joints have been specified for many years to accommodate movement in piping runs and insure efficient systems. Elastomer joints are widely used to provide efficient ways to relieve movement stresses, reduce noise, isolate vibration, compensate for misalignment. Teflon joints are used with highly corrosive media, with glass piping, or in systems where space is at a premium.
[Show full text]
January 2021
LEXINGTON COUNTY SCHOOL DISTRICT ONE DISBURSEMENTS BY CHECK/EFT NO. From 1/1/2021 to 1/31/2021 Check/ EFT Check/ EFT Vendor No. Date Account Key Object No. Vendor Name PO # Invoice # Description Amount 00100296 01/07/2021 1000000000 245570 V15433 ASIFLEX 2400/2101010 AP INTERFACE 1-10-2021 41,823.94 00100296 01/07/2021 1000000000 245550 V15433 ASIFLEX 2402/2101010 AP INTERFACE 1-10-2021 3,980.21 00100296 01/07/2021 1000000000 245470 V15433 ASIFLEX 2410/2101010 AP INTERFACE 1-10-2021 5,206.63 Check Total 51,010.78 00100297 01/07/2021 1000000000 245540 V15443 ASIFLEX 2492/2101010 AP INTERFACE 1-10-2021 713.40 00100297 01/07/2021 1000000000 245540 V15443 ASIFLEX 2494/2101010 AP INTERFACE 1-10-2021 27.84 00100297 01/07/2021 1000000000 245540 V15443 ASIFLEX 2496/2101010 AP INTERFACE 1-10-2021 36.00 Check Total 777.24 00100298 01/07/2021 1000000000 245710 V01954 WELLS FARGO BANK NA CUSTODIAN 2600/2101010 AP INTERFACE 1-10-2021 55,017.96 00100298 01/07/2021 1000000000 245730 V01954 WELLS FARGO BANK NA CUSTODIAN 2610/2101010 AP INTERFACE 1-10-2021 20,110.14 00100298 01/07/2021 1000000000 245980 V01954 WELLS FARGO BANK NA CUSTODIAN 2650/2101010 AP INTERFACE 1-10-2021 5,315.53 00100298 01/07/2021 1000000000 245970 V01954 WELLS FARGO BANK NA CUSTODIAN 2660/2101010 AP INTERFACE 1-10-2021 1,094.91 00100298 01/07/2021 1000000000 245820 V01954 WELLS FARGO BANK NA CUSTODIAN 2770/2101010 AP INTERFACE 1-10-2021 8,828.00 00100298 01/07/2021 1000000000 245850 V01954 WELLS FARGO BANK NA CUSTODIAN 2775/2101010 AP INTERFACE 1-10-2021 1,747.00 Check Total 92,113.54
[Show full text]
The Development and Use of Bib Overalls in the United States, 1856-1945 Ann Revenaugh Hemken Iowa State University
Iowa State University Capstones, Theses and Retrospective Theses and Dissertations Dissertations 1993 The development and use of bib overalls in the United States, 1856-1945 Ann Revenaugh Hemken Iowa State University Follow this and additional works at: https://lib.dr.iastate.edu/rtd Part of the American Material Culture Commons, Fashion Business Commons, Fashion Design Commons, and the Other History Commons Recommended Citation Hemken, Ann Revenaugh, "The development and use of bib overalls in the United States, 1856-1945 " (1993). Retrospective Theses and Dissertations. 337. https://lib.dr.iastate.edu/rtd/337 This Thesis is brought to you for free and open access by the Iowa State University Capstones, Theses and Dissertations at Iowa State University Digital Repository. It has been accepted for inclusion in Retrospective Theses and Dissertations by an authorized administrator of Iowa State University Digital Repository. For more information, please contact [email protected]. The development and use of bib overalls in the United States, 1856-1945 by Ann Revenaugh Hemken A Thesis Submitted to the Graduate Faculty in Partial Fulfillment of the Requirements for the Degree of MASTER OF SCIENCE Department: Textiles and Clothing Major: Textiles and Clothing Signatures have been redacted for privacy Iowa State University Ames, Iowa 1993 ii TABLE OF CONTENTS LIST OF FIGURES................................................ iii ACKNOWLEDGMENTS. • • • • • • . • • • • • • • • • • . • • • . • • • • • • • • • • • • • . • • • • • • • . • •• i v INTRODUCTION
[Show full text]