Product Information
CompactPCI® Pentium® M CPU Board • CD2-BEBOP
Document No. 3236 • Edition 2008-02
Equipped with the Intel® Pentium® M processor up to For mass storage attachment, the CD2-BEBOP provides 2GHz, the CD2-BEBOP is a high performance, low power both Ultra ATA/100 IDE and RAID capable S-ATA 6U (double size Eurocard) CompactPCI® CPU board. interfaces. In addition, a socket for CompactFlash cards allows utilization of a silicon disk. The CD2-BEBOP is provided with an embedded graphics controller. The user can choose between a DVI-I The main memory is a SO-DIMM 200 DDR-SDRAM receptacle, which allows for attachment of both, module up to 1GB capacity. An on-board USB2.0 FLASH advanced (digital) and legacy (analog) flat panel displays disk drive up to 2GB is available as an option. and CRT monitors, or the classic VGA D-Sub connector. The Pentium® M (in particular the Low Voltage 1.4GHz The PMC mezzanine card socket enables on-board chip) reduces the power consumption considerably expansion of the CD2-BEBOP. Alternatively, an on-board compared to previous processor generations, thus hard disk drive module is optionally available which fits enabling a reliable passive heatsink solution for thermal on the PMC slot as well. discharge. In addition to the front panel connectors, the optional In addition to several USB2.0 ports, the CD2-BEBOP is CDY-RIO rear I/O transition module offers a variety of on- equipped with four independent Ethernet controllers for board and back panel connectors for a versatile usage of high speed networking up to 1000Mbps. The PICMG® the CD2-BEBOP. 2.16 Packet Switching Backplane is also supported (Dual Link Port).
CD2-BEBOP
- 1 - EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 HAMM • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • E-Mail [email protected] • Internet www.ekf.com CD2-BEBOP • CompactPCI Pentium® M CPU
Feature Summary CD2-BEBOP
Form Factor Double size CompactPCI style Eurocard (160x233mm2), front panel width 4HP (20.3mm)
Processor Designed for Intel® Pentium® M Micro FC-BGA 479 processors (0.13 Banias, 0.09 Dothan), maximum junction temperature 100°C • 600MHz ULV Celeron® M, 512KB L2 cache, 7W • 1.4GHz LV Pentium® M (Dothan733), 2MB L2 cache, 10W • 1.8GHz Pentium® M (Dothan745), 2MB L2 cache, 21W • 2.0GHz Pentium® M (Dothan755), 2MB L2 cache, 21W
Chipset Intel® i855 chipset consisting of: • 82855GME Graphics/Memory Controller Hub (GMCH) - Montara • 82801D I/O Controller Hub (ICH4) • 82802 Compatible Firmware Hub (FWH)
Memory • 200-pin SO-DIMM socket (notebook style module), PC2100/2700 DDR266/333- SDRAM, 1GB maximum • USB FLASH drive on-board (option), up to 2GByte bootable NAND Flash with USB2.0 controller
Video Analog monitor and digital flat-panel display support by DVI-I connector (front panel), up to 2048x1536 pixel 16M colours @75Hz refresh rate (analog), up to 1600 x 1200 pixel 16M colours @60Hz (digital), incorporates PanelLink Digital technology (Silicon Image). Front panel option: D-Sub (female HD15) VGA connector available, replaces DVI-I connector
USB All ports over-current protected, data transfer rate of up to 480Mbps, conforming to USB2.0 • USB port 1-2: Type A connector (front panel) • USB port 6: Expansion interface option (CCA-LAMBADA mezzanine companion board) • USB port 3-5: J4/P4 Rear I/O option (CDY-RIO rear I/O transition module) • USB port 4 dedicated to the optional on-board USB Flash drive
Ethernet • 3 x 10/100/1000Mbps Gigabit Ethernet controllers (82541ER) • Jumbo Frame support up to 16KB • 1 x 10/100Mbps Fast Ethernet Controller (82562) • 1 x Gigabit and Fast Ethernet accessible via RJ45 jacks from the front panel • 2 x Gigabit Ethernet as rear I/O according to PICMG® 2.16 across J3 (alternatively accessible via RJ45 jacks from the CDY-RIO back panel)
IDE/ATA (Parallel) • Ultra ATA/100 connector (Secondary IDE), handover to CCA-LAMBADA mezzanine expansion board with CCA on-board hard disk drive or external device • CompactFlash socket (mezzanine module) for CFA ATA cards (Secondary IDE) • J4/P4 Rear I/O option: Primary IDE accessible from CDY-RIO rear I/O transition module • CD2 on-board hard disk drive module option (Primary IDE)
Serial ATA On-board dual port Serial ATA controller, ports available across J5/P5 on CDY-RIO rear I/O module (alternatively accessible via Serial ATA connectors on board), RAID and non-RAID drivers available
FLASH Drive Optional on-board USB2.0 FLASH drive controller and 2 pcs. NAND FLASH up to 8Gbit each (total memory capacity up to 2GByte), can be configured as bootable disk, data transfer rates up to 18MB/s for read, 13MB/s for write (dual channel mode)
Mezzanine Facility Optional usage of either • 1 Slot for a PMC module, I/O from the front panel and across J5 • On-board 2.5-inch hard disk module (Primary IDE)
Expansion • On-board LPC/USB/AC97 Super-I/O, USB and audio expansion interface connector Interface • Suitable CCA-LAMBADA 3U mezzanine companion board available
- 2 - EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 HAMM • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • E-Mail [email protected] • Internet www.ekf.com CD2-BEBOP • CompactPCI Pentium® M CPU
Feature Summary CD2-BEBOP
Rear I/O • 2 x Gigabit Ethernet (J3) • 2 x Serial ATA (J3) • Primary IDE (J4) • 2 x USB (J4) • LPT, COM, GPIO (J4) • PMC mezzanine rear I/O (J5) • Suitable rear I/O transition module CDY-RIO available
CompactPCI® 32-bit PCI bridge chip PLX PCI 6150 (HB4), 133MBps CPCI master, transparent mode (CPCI system slot operation). When using the CD2-BEBOP on a peripheral slot the PCI bridge must be removed (special board versions available on request)
Hot Swap Function Board hot insertion/extraction without adversely effecting a running system, 'Basic Hot Swap' implementation according to CompactPCI Hot Swap Specification PICMG® 2.1. In order to use the CD2-BEBOP as a peripheral slot board, the local PCI bridge must be removed (stand-alone operation or PICMG 2.16 communications path required instead of PCI bus data exchange), special board versions are available on request
PICMG® 2.16 Dual Link Port Node, complies with the PICMG® 2.16 CompactPCI® Packet Switching Backplane Specification
BIOS Phoenix BIOS
Typical Power • +5V +0.25V/-0.15V tbd A max. Consumption • +3.3V +0.17V/-0.1V tbd A max.
Thermal • Operating temperature: 0°C ... +70°C (CPU dependent) Conditions • Storage temperature: -40°C ... +85°C, max. gradient 5°C/min Environmental • Humidity 5% ... 95% RH non condensing Conditions • Altitude -300m ... +3000m • Shock 15g 0.33ms, 6g 6ms • Vibration 1g 5-2000Hz
EC Regulations EN55022, EN55024, EN60950-1 (UL60950-1/IEC60950-1)
Performance Board Processor CPU/MEM Score Rating CD2-1X-BEBOP 1.4GHz LV Pentium® M (Dothan 738) 4745/8489 Measured with PCMark2002 CD2-2X-BEBOP 1.8GHz Pentium® M (Dothan 745) 6100/10441 under Windows XP, 512MB CD2-3X-BEBOP 2.0GHz Pentium® M (Dothan 755) 6773/11398 PC2700 DDR
MTBF tbd h
subject to change
- 3 - EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 HAMM • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • E-Mail [email protected] • Internet www.ekf.com CD2-BEBOP • CompactPCI Pentium® M CPU
CD2-BEBOP with DE2-TIGER PMC Module
CD2-BEBOB with on-Board CompactFlash Module & DB1-FALCON PMC Module
- 4 - EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 HAMM • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • E-Mail [email protected] • Internet www.ekf.com CD2-BEBOP • CompactPCI Pentium® M CPU
CD2-BEBOP with 2.5-Inch Hard Disk Module on-Board
CD2-BEBOB with on-Board 1.8-Inch Hard Disk
- 5 - EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 HAMM • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • E-Mail [email protected] • Internet www.ekf.com CD2-BEBOP • CompactPCI Pentium® M CPU
Block Diagram CD2-BEBOP 1/2
Block Diagram CD2-BEBOP Sheet 1/2
FSB 400MHz
DVI Panel DVO DDR-SDRAM 512MB/1GB Link GMCH PC2100/2700
DVI-I RGB 855GME 1GB (max) 1GB Digital/Analog DDR SO-DIMM Hub Sheet 2J4 Link J4 Sheet 2
VGA J4 PIDE USB VGA D-SUB USB ICH4 SIDE IDE I/F
USB C10-CFA CompactFlash AC'97 82 ATA 82 LPC 802 FWH BIOS
Expansion Board 802 Expansion I/F Expansion Opt. CCA-LAMBADA Opt. LCI LPC Local PCI
10/100 82 ETH 6150 562 Ethernet Controller PCI to PCI Bridge CompactPCI CompactPCI ETH 82 10/100/1000 541 J1 J2
Sheet 2 GMCH VGA USB ICH4 PIDE ICH4 Front Panel I/O COM KB PS/2 GPIO Super I/O CompactPCI MS 8761 PS/2 J4
- 6 - EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 HAMM • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • E-Mail [email protected] • Internet www.ekf.com CD2-BEBOP • CompactPCI Pentium® M CPU
Block Diagram CD2-BEBOP 2/2
Sheet 1 Block Diagram CD2-BEBOP Sheet 2/2 82 ETH Gigabit 541 PICMG Ethernet 10/100/1000 2.16 Controller 82 ETH 541 CompactPCI J3 Local PCI Serial ATA Dual Controller 35 SATA-1 SATA SATA-0 12 Front PanelI/O
PMC Rear I/O CompactPCI J5 PCI 12 PMC Mezzanine
4 PIDE
C11-HDD 2.5-" HD Module
1 x PMC Module or 1 x 2.5-" Hard Disk Module Sheet 1
USB4 UT Sheet 1 168 up to 2GBytes NAND Flash NAND FLASH Drive Option
Basic Hot Swap Local Power 16 CPCI Power Controller PICMG 2.1 46
- 7 - EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 HAMM • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • E-Mail [email protected] • Internet www.ekf.com CD2-BEBOP • CompactPCI Pentium® M CPU
Orientation of Connectors CD2-BEBOP
JRTC JRST SATA CON1 SATA CON2 1 1 CompactPCI JFD
12 12 J5
MJ1 MJ2 SATA
USB4 Flashdrive
1 2 Com p J4
MJ4 actPCI
PMC Mezzanine
541
541 PS2
ETH
ATA / IDE Module Expansion Module USB2 1 1 LPC / AC’97
USB1 855 GMCH Reset
G- Pentium ETH M ICH4 541
DVI-I
CompactFlash / 1.8-Inch Hard Disk Option
VGA DDR SOReset -DIMM 200
- 8 - EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 HAMM • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • E-Mail [email protected] • Internet www.ekf.com CD2-BEBOP • CompactPCI Pentium® M CPU
Front Panel I/O Functions CD2-BEBOP
CD2- BEBOP
P M C
M E Z Z A N I N E
ETH3
K B / M S
E T H 2 ETH4
USB
G P
I D E PWR/RES
H S
ETH1
D V I
- 9 - EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 HAMM • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • E-Mail [email protected] • Internet www.ekf.com CD2-BEBOP • CompactPCI Pentium® M CPU
CD2-BEBOB with CDY-RIO (Rear I/O Transition Module Option)
CDY-RIO Rear I/O Module
- 10 - EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 HAMM • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • E-Mail [email protected] • Internet www.ekf.com CD2-BEBOP • CompactPCI Pentium® M CPU
CDY-RIO Block Diagram 1/2
Serial ATA P-SA2 optional PMC
SA back panel PMC adapter SATA SATA PMC Rear I/O J5 Mezzanine I/O P-PMC
Block Diagram USB5 CDY-RIO LM 35 USB3 26 Rear I/O CD2-BEBOP P-CU
ADM COM (RS-232) CU USB SA 211 COM COM (TTL) P-SA1 JMP-COM GPIO P-GPIO GPIO PS/2
VGA KB
CompactPCI MS J4 IDE VGA
P-IDE2 BCT C00-HD 16 (optional) 245 IDE 40 IDE 44
JMP-IDE P-IDE1 Back Panel I/O Back Panel
ETH 10/100/1000Mbps Ethernet (J3 Option) ETH CompactPCI CompactPCI
J3 6U 4/8HP
- 11 - EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 HAMM • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • E-Mail [email protected] • Internet www.ekf.com CD2-BEBOP • CompactPCI Pentium® M CPU
CDY-RIO Block Diagram 2/2
Block Diagram C00-HD
2.5" Hard Disk
IDE 44 P-IDE5
CDY-RIO IDE 44 P-IDE3
IDE 44 P-IDE4
2.5-" Hard Disk CDY-RIO Back PanelCDY-RIO I/O
6U 8HP
- 12 - EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 HAMM • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • E-Mail [email protected] • Internet www.ekf.com CD2-BEBOP • CompactPCI Pentium® M CPU
Back Panel CDY-RIO
M E Z Z A N I N E
CDY- RIO
U S B SATA S S 1 2 U S B
C O M
K B M / S M S
V G A
E T H 2
E
8HP Panel 8HP Width w Option C00-HD T H 3
- 13 - EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 HAMM • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • E-Mail [email protected] • Internet www.ekf.com CD2-BEBOP • CompactPCI Pentium® M CPU
Ordering Information
Alias Ordering No. Short Description
BEBOP CD2-1A-BEBOP 6U, LV Pentium M 1.4GHz 738, 512MB DDR SDRAM, 6 x USB, 4 x Ethernet (3 x GB), PICMG 2.16 Dual Link, IDE, SATA, CompactFlash ATA slot, 1 x PMC mezzanine, DVI-I video, rear I/O, on-board USB Flash drive
BEBOP CD2-1B-BEBOP similar to CD2-1A-BEBOP, w/o on-board USB Flash drive
BEBOP CD2-1C-BEBOP similar to CD2-1A-BEBOP, w/o on-board USB Flash drive, w/o 2.16 rear I/O Ethernet
BEBOP CD2-1H-BEBOP similar to CD2-1A-BEBOB, on-board 2.5-inch hard disk mezzanine module (replaces PMC slot)
BEBOP CD2-2A-BEBOP 6U, Pentium M 1.8GHz 745, 512MB DDR SDRAM, 6 x USB, 4 x Ethernet (3 x GB), PICMG 2.16 Dual Link, IDE, SATA, CompactFlash ATA slot, 1 x PMC mezzanine, DVI-I video, rear I/O, on-board USB Flash drive
BEBOP CD2-2B-BEBOP similar to CD2-2A-BEBOP, w/o on-board USB Flash drive
BEBOP CD2-2C-BEBOP similar to CD2-2A-BEBOP, w/o on-board USB Flash drive, w/o 2.16 rear I/O Ethernet
BEBOP CD2-2H-BEBOP similar to CD2-2A-BEBOB, on-board 2.5-inch hard disk mezzanine module (replaces PMC slot)
BEBOP CD2-3A-BEBOP 6U, Pentium M 2.0GHz 755, 512MB DDR SDRAM, 6 x USB, 4 x Ethernet (3 x GB), PICMG 2.16 Dual Link, IDE, SATA, CompactFlash ATA slot, 1 x PMC mezzanine, DVI-I video, rear I/O, on-board USB Flash drive
BEBOP CD2-3B-BEBOP similar to CD2-3A-BEBOP, w/o on-board USB Flash drive
BEBOP CD2-3C-BEBOP similar to CD2-3A-BEBOP, w/o on-board USB Flash drive, w/o 2.16 rear I/O Ethernet
BEBOP CD2-3H-BEBOP similar to CD2-3A-BEBOB, on-board 2.5-inch hard disk mezzanine module (replaces PMC slot)
BEBOP CD2-H-BEBOP On-board 1.8-inch hard disk module option, replaces CompactFlash socket adapter
BEBOP CD2-Z-BEBOP 1GB Memory option
RIO CDY-1-RIO J3/J4/J5 rear I/O transition module 6U/4HP
RIO CDY-2-RIO J3/J4/J5 rear I/O transition module 6U/8HP with 2.5-inch rear I/O hard disk
LAMBADA CCA-1-LAMBADA 3U mezzanine module, local expansion board complementing the CD2-BEBOP, front panel width 4HP, optional AC'97 codec
FALCON DB1-1-FALCON PMC module, USB2.0 host adapter
TIGER DE2-2-TIGER PMC module, SATA controller + 1.8-inch hard disk drive
280.7.400 External PS/2 keyboard/mouse Y-splitter-cable mini-DIN male to 2 x mini-DIN female
908.51.02.01 DVI-D to DVI-D cable assembly, 2m, connects the CD2-BEBOP to DVI monitors (digital way)
908.57.02.01 DVI-I to HD DSUB15 cable assembly, 2m, connects the CD2-BEBOP to VGA monitors (analog way)
908.57.12.01 DVI-I to VGA adapter (plug to receptacle), to be plugged onto the CD2-BEBOP DVI output, with HD DSUB15 socket, suitable especially for analog monitors with attached VGA cable
- 14 - EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 HAMM • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • E-Mail [email protected] • Internet www.ekf.com CD2-BEBOP • CompactPCI Pentium® M CPU
Suitable 1U CPCI System Rack CR1
Suitable 7U CPCI System Rack CR7
- 15 - EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 HAMM • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • E-Mail [email protected] • Internet www.ekf.com CD2-BEBOP • CompactPCI Pentium® M CPU
DB1-FALCON Five-Port USB PMC Module
DE2-TIGER Quad-Port SATA RAID PMC Module
EKF Elektronik GmbH Fax. +49 (0)2381/6890-90 Philipp-Reis-Str. 4 Tel. +49 (0)2381/6890-0 59065 HAMM Internet www.ekf.com Germany E-Mail [email protected]