DOCSLIB.ORG

Column Study of the Adsorption of Phosphate by Using Drinking Water Treatment Sludge and Red Mud

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Column Study of the Adsorption of Phosphate by Using Drinking Water Treatment Sludge and Red Mud International Journal of Civil Engineering and Technology (IJCIET) Volume 6, Issue 9, Sep 2015, pp. 08-19, Article ID: IJCIET_06_09_002 Available online at http://www.iaeme.com/IJCIET/issues.asp?JTypeIJCIET&VType=6&IType=9 ISSN Print: 0976-6308 and ISSN Online: 0976-6316 © IAEME Publication ___________________________________________________________________________ COLUMN STUDY OF THE ADSORPTION OF PHOSPHATE BY USING DRINKING WATER TREATMENT SLUDGE AND RED MUD Prof. Dr. Alaa Hussein Al-Fatlawi College of Engineering / Babylon University/Iraq Mena Muwafaq Neamah College of Engineering / Babylon University/Iraq ABSTRACT The present study investigates the efficiency of phosphate removal from wastewater by the Drinking Water Treatment Sludge (DWTS), and Red Mud (RM) sorbent. Wastewater was taken from the effluent channel of Almuamirah wastewater treatment plantin at Al-Hilla city/Iraq. Drinking Water Treatment Sludge (DWTS), was taken from the sedimentation tanks of Al-Tayara drinking water treatment plant, in the same city. Column experiment was carried out to study the adsorption isotherm of phosphorus at 25±1⁰C and solution of different pH and adsorbent dosages. The effects of (DWTS) dose, bed height (H), contact time (T), agitation speed (S), hydrogen ion concentration (pH), (DWTS –RM) ratio, were studied. All continuous experiments were conducted at constant conditions, bed depths 25 cm, initial phosphate concentration 4 mg/L, flow rate 5 mL/min, particle size (1mm) for (DWTS), and (0.425mm) for (RM) and solution pH of 4. The results show that the use of (RM) reduces the operating time by about 21% compared to the use of (DWTS).Increasing (RM) ratio increasing the removal efficiency and decreasing the equilibrium time in about 57% and 38% for 50% and 33% (RM) ratio respectively. At the highest phosphate concentration of 4 mg/l, the (DWTS) bed was exhausted in the shortest time of less than 9 hours leading to the earliest breakthrough. Percent of phosphate removal decreased with the increase in initial concentration. Both the breakthrough and exhaustion time increased with increasing the bed height. The results show that a significant increase in the operating time is achieved by adding different ratios of (RM) to (DWTS). Adding 33%, and 50 % (RM) weight ratios to the (DWTS) bed decreases the operating time by about 18%, and 30% respectively. http://www.iaeme.com/IJCIET/index.asp 8 [email protected] Column Study of The Adsorption of Phosphate by Using Drinking Water Treatment Sludge and Red Mud Key words: Column Study, Adsorption, Drinking Water Treatment Sludge (DWTS), and Red Mud (RM), phosphate. Cite this Article: Prof. Dr. Alaa Hussein Al-Fatlawi and Mena Muwafaq Neamah. Investigating Column Study of The Adsorption of Phosphate by Using Drinking Water Treatment Sludge and Red Mud. International Journal of Civil Engineering and Technology, 6(9), 2015, pp. 08-19. http://www.iaeme.com/IJCIET/issues.asp?JTypeIJCIET&VType=6&IType=9 1. INTRODUCTION Phosphorus (P) is an essential nutrient for the growth of organisms in most ecosystems, but superfluous phosphorus can also cause eutrophication and hence deteriorate water quality. Phosphorus is released into aquatic environments in many ways, of which the most significant are human industrial, agricultural, and mining activities. Although phosphorus removal is required before discharging wastewater into bodies of water, phosphorus pollution is nevertheless increasing. Therefore, there is currently an urgent demand for improved phosphorus removal methods which can be applied before wastewater discharge. In wastewater treatment, enhanced biological phosphorus removal (EBPR) is becoming an increasingly popular alternative to chemical precipitation (CP) because of its lower costs and reduced sludge production. Much water treatment sludge is produced in the production of service water and drinking water. It is impossible to prevent the production of water treatment sludge. The water treatment sludge is liquid and solid and is regarded as a waste. Consequently, the water treatment sludge must be handled in accordance with regulations in forces. The quantity of the water treatment sludge is rather high. The water treatment sludge is placed mostly in landfills. In some countries, for instance in the Netherlands, about 25 per cent of the produced water treatment sludge is re-used, (Miroslav, 2008). It is still an issue to choose a disposal or liquidation method for the water treatment sludge that would be reasonable in terms of technology and economy. According to environment protection regulations it is required to minimise the quantity of wastes produced. If possible, the wastes should be re-used or processed as secondary raw materials as much as possible. If this is not possible, the solid wastes should be put back in the environment where the space occupied should be as little as possible and minimum costs should be incurred, (Moldan et al., 1990). Phosphorus removal from wastewater has been widely investigated and several techniques have been developed including adsorption methods, physical processes (settling, filtration), chemical precipitation (with aluminum, iron and calcium salts), and biological processes that rely on biomass growth (bacteria, algae, plants) or intracellular bacterial polyphosphates accumulation (de-Bashan et al., 2004). Recently, the removal of phosphate from aqueous solutions via adsorption has attracted much attention. The key problem for many phosphorus adsorption methods, however, is finding an efficient adsorbent. Several low-cost or easily available clays, waste materials and by-products. http://www.iaeme.com/IJCIET/index.asp 9 [email protected] Prof. Dr. Alaa Hussein Al-Fatlawi and Mena Muwafaq Neamah 2. MATERIAL AND METHODS 2.1 Adsorbate Phosphate was selected as a representative of a contaminant because the it is the main nutrient for the growth of aquatic microorganisms like algae but the excess content of phosphorus in receiving waters leads to extensive algae growth (eutrophication). The samples was collected from the effluent channel of Almuamirah wastewater treatment plant in Al-Hilla city, Iraq. These samples were immediately transported to the laboratory for processing. The total amount of plant nutrients and other pollutants present in a sewage plant effluent is subjected to seasonal, daily, and hourly variation. Table 1 summarizes the composition and variability of the effluent under study. The wastewater sample was used as stock solution to provide the specific value of phosphate concentration. Where necessary, pH adjustment was made on each sample by addition of 0.1 M HNO3 and NaOH solutions using a HACH-pH meter. Table 1 Physico-chemical analysis of secondary wastewater effluent sample, (Almuamirah wastewater treatment plant, 2014) parameters Quantitative composition E.C, µs/cm 3.5 T.D.S, mg/L 1288 Salinity, mg/L 2.18 Total hardness, as CaCo3, mg/L 1200 pH 7.9 Mg, mg/L 232.8 Ca, mg/L 160.3 So4, mg/L 769.4 Cl, mg/L 289.9 Po4, mg/L 2.7 No3, mg/L 0.46 T.S.S, mg/L 40 BOD5, mg/L 32 COD, mg/L 54 DO, mg/L 2.3 Fecal coliform, mpn/100 ml 120000 Total coliform, mpn/100 ml 128000 2.2 Adsorbent Two types of adsorbent were used in the present study for adsorption of phosphate from secondary effluents of wastewater treatment plant they are: 1. Drinking Water Treatment Sludge (DWTS), 2. Red Mud (RM). 2.2.1. Drinking Water Treatment Sludge (DWTS) The composition and properties of the water treatment sludge depends typically on the quality of treated water as well as on types and doses of chemicals used during the http://www.iaeme.com/IJCIET/index.asp 10 [email protected] Column Study of The Adsorption of Phosphate by Using Drinking Water Treatment Sludge and Red Mud water treatment. Depending on the quality of the treated water, the water treatment sludge contains suspensions of inorganic and organic substances. The (DWTS) used in this study was taken from the sedimentation tanks of Al- Tayara drinking water treatment plant, in Al-Hilla city, Iraq. This sludge was dried at atmospheric temperature for 5 days, and then sieved on 2 mm mesh to achieve satisfactory uniformity. The sludge had a particle size distribution ranged from 150 μm to 10 mm (Fig. 1) with an effective grain size, d10, of 250 μm, a median grain size, d50, of 460 μm and a uniformity coefficient, Cu= d60/d10, of 2.24. 120 100 80 60 40 % of cumulative passing cumulative of % 20 0 0.1 1 10 Partical size (diameter , mm) Figure 1 Gradation curve for (DWTS) used in the present study. The geometric mean diameter (1.19) is given by where d1 is the diameter of lower sieve on which the particles are retained and d2 is the diameter of the upper sieve through which the particles pass (Alexander and Zayas, 1989). Table 2 presents the physical and chemical characteristics of this (DWTS). Table 2 Physical and chemical characteristics of DWTS Element Quantitative composition T.O.C, mg/L 4.29 E.C, µs/cm 620 T.D.S, mg/L 312 Salinity, mg/L 0.2 pH 8.1 L.O.I, mg/L 15.76 Fe2O3, mg/L 3.6 CaO, mg/L 15.32 SO3, mg/L 0.63 MgO, mg/L 3.66 Al2O3, mg/L 11.56 R2O3, mg/L 15.16 SiO2, mg/L 45 2.2.2. Red Mud (RM) The Red Mud (RM) used in this study was supplied by the Iraqi commercial markets. It is a solid waste produced in the process of alumina production from bauxite following the Bayer process. Red mud, as the name suggests, is brick—red in colour and slimy, having an average particle size of <10μm. A few particles greater than http://www.iaeme.com/IJCIET/index.asp 11 [email protected] Prof. Dr. Alaa Hussein Al-Fatlawi and Mena Muwafaq Neamah 20μm are also available [Liu et al., 2011].The mesh size of red mud used in the study was of 1mm.
Load more

Recommended publications
  • Eparation of the Purest Aluminum Chemicals
    III. MINERAL COMMODITIES A. INDIVIDUAL MINERAL COMMODITY REVIEWS ALUMINA & ALUMINUM A. Commodity Summary Aluminum, the third most abundant element in the earth's crust, is usually combined with silicon and oxygen in rock. Rock that contains high concentrations of aluminum hydroxide minerals is called bauxite. Although bauxite, with rare exceptions, is the starting material for the production of aluminum, the industry generally refers to metallurgical grade alumina extracted from bauxite by the Bayer Process, as the ore. Aluminum is obtained by electrolysis of this purified ore.1 The United States is entirely dependent on foreign sources for metallurgical grade bauxite. Bauxite imports are shipped to domestic alumina plants, which produce smelter grade alumina for the primary metal industry. These alumina refineries are in Louisiana, Texas, and the U.S. Virgin Islands.2 The United States must also import alumina to supplement this domestic production. Approximately 95 percent of the total bauxite consumed in the United States during 1994 was for the production of alumina. Primary aluminum smelters received 88 percent of the alumina supply. Fifteen companies operate 23 primary aluminum reduction plants. In 1994, Montana, Oregon, and Washington accounted for 35 percent of the production; Kentucky, North Carolina, South Carolina, and Tennessee combined to account for 20 percent; other states accounted for the remaining 45 percent. The United States is the world’s leading producer and the leading consumer of primary aluminum metal. Domestic consumption in 1994 was as follows: packaging, 30 percent; transportation, 26 percent; building, 17 percent; electrical, 9 percent; consumer durables, 8 percent; and other miscellaneous uses, 10 percent.
    [Show full text]
  • FOILING the ALUMINUM INDUSTRY: a TOOLKIT for COMMUNITIES, ACTIVISTS, CONSUMERS, and WORKERS by International Rivers Network FOILING the ALUMINUM INDUSTRY
    FOILING THE ALUMINUM INDUSTRY: A TOOLKIT FOR COMMUNITIES, ACTIVISTS, CONSUMERS, AND WORKERS by International Rivers Network FOILING THE ALUMINUM INDUSTRY: A TOOLKIT FOR COMMUNITIES, ACTIVISTS, CONSUMERS, AND WORKERS By Glenn Switkes Published by International Rivers Network, August 2005 Copyright © 2005 International Rivers Network 1847 Berkeley Way Berkeley, CA 94703 USA IRN gratefully acknowledges the support of The Overbrook Foundation, whose funding made this toolkit possible. Design by: Design Action Collective Graphic chart: Soft Horizons & Chartbot Foiling the Aluminum Industry Table of Contents INTRODUCTION ............................................................................................................1 THE ALUMINUM INDUSTRY TODAY AND TOMORROW ................................................................3 FIRST STEP : ..............................................................................................................5 Stripping forests for bauxite ................................................................................5 Stripping the Amazon ..........................................................................................6 Bauxite mining brings violence against indigenous people ......................................8 SECOND STEP : ............................................................................................................9 Alumina refining—white powder and red mud ........................................................9 Jamaicans demand to know whether their water supplies
    [Show full text]
  • Iron Recovery from Bauxite Tailings Red Mud by Thermal Reduction with Blast Furnace Sludge
    applied sciences Article Iron Recovery from Bauxite Tailings Red Mud by Thermal Reduction with Blast Furnace Sludge Davide Mombelli * , Silvia Barella , Andrea Gruttadauria and Carlo Mapelli Dipartimento di Meccanica, Politecnico di Milano, via La Masa 1, Milano 20156, Italy; [email protected] (S.B.); [email protected] (A.G.); [email protected] (C.M.) * Correspondence: [email protected]; Tel.: +39-02-2399-8660 Received: 26 September 2019; Accepted: 9 November 2019; Published: 15 November 2019 Abstract: More than 100 million tons of red mud were produced annually in the world over the short time range from 2011 to 2018. Red mud represents one of the metallurgical by-products more difficult to dispose of due to the high alkalinity (pH 10–13) and storage techniques issues. Up to now, economically viable commercial processes for the recovery and the reuse of these waste were not available. Due to the high content of iron oxide (30–60% wt.) red mud ranks as a potential raw material for the production of iron through a direct route. In this work, a novel process at the laboratory scale to produce iron sponge ( 1300 C) or cast iron (> 1300 C) using blast furnace ≤ ◦ ◦ sludge as a reducing agent is presented. Red mud-reducing agent mixes were reduced in a muffle furnace at 1200, 1300, and 1500 ◦C for 15 min. Pure graphite and blast furnace sludges were used as reducing agents with different equivalent carbon concentrations. The results confirmed the blast furnace sludge as a suitable reducing agent to recover the iron fraction contained in the red mud.
    [Show full text]
  • Recovery of Value Added Products from Red Mud and Foundry Bag
    RECOVERY OF VALUE-ADDED PRODUCTS FROM RED MUD AND FOUNDRY BAG-HOUSE DUST by Keegan Hammond i A thesis submitted to the Faculty and the Board of Trustees of the Colorado School of Mines in partial fulfillment of the requirements for the degree of Master of Science (Metallurgical and Materials Engineering). Golden, Colorado Date ______________ Signed: ____________________________ Keegan Hammond Signed: ____________________________ Dr. Brajendra Mishra Thesis Advisor Golden, Colorado Date ______________ Signed: ____________________________ Dr. Chester VanTyne Interim Department Head Department of Metallurgical and Materials Engineering ii ABSTRACT “Waste is wasted if you waste it, otherwise it is a resource. Resource is wasted if you ignore it and do not conserve it with holistic best practices and reduce societal costs. Resource is for the transformation of people and society.”1 Red mud is a worldwide problem with reserves in the hundreds of millions of tons and tens of millions of tons being added annually. Currently there is not an effective way to deal with this byproduct of the Bayer Process, the primary means of refining bauxite ore in order to provide alumina. This alumina is then treated by electrolysis using the Hall-Héroult process to produce elemental aluminum. The resulting mud is a mixture of solid and metallic oxides, and has proven to be a great disposal problem. This disposal problem is compounded by the fact that the typical bauxite processing plant produces up to three times as much red mud as alumina. Current practice of disposal is to store red mud in retention ponds until an economical fix can be discovered.
    [Show full text]
  • Effect of Red Mud Content on Strength and Efflorescence in Pavement Using Alkali-Activated Slag Cement
    International Journal of Concrete Structures and Materials DOI 10.1186/s40069-018-0258-3 ISSN 1976-0485 / eISSN 2234-1315 Effect of Red Mud Content on Strength and Efflorescence in Pavement using Alkali-Activated Slag Cement Kim Hyeok-Jung1), Suk-Pyo Kang2),* , and Gyeong-Cheol Choe3) (Received September 28, 2017, Accepted February 6, 2018) Abstract: Efflorescence which severely occurs in alkali-activated slag cement can cause reduction of strength and durability due to calcium leaching. In the work, efflorescence characteristics in pavement containing red mud which can be affected by strong alkaline were investigated through various tests such as compressive strength, porosity, absorption, efflorescence area, alkali leaching content, and properties of the efflorescence compound. The compressive strength of pavement was evaluated to be higher over 15.0 MPa in all cases regardless of replacement ratio of red-mud and binder type, which can provide a reasonable strength for walking and bike lanes. The pavement with red mud was applicable to parking lots only when the replacement ratio of red-mud is within 10%. The efflorescence area increased with a higher replacement ratio of red mud and its propagation appeared though the efflorescence was removed through evaporation of moisture. However, the area of efflorescence gradually decreased with the repetition of the test. Keywords: pavement, alkali-activated slag cement, red mud, efflorescence, compaction. 1. Introduction 2017; Kang 2016). Another effort for utilizing red mud as an activator has been made for alkali slag red mud cement in With increasing significance of human-friendly environ- the construction industry, which is so called clinker-free ment and sustainability, eco-friendly pavement materials cement (Gonga and Yang 2000; Pan et al.
    [Show full text]
  • Natural Radioactivity in Egyptian and Industrially Used Australian Bauxites and Its Tailing Red Mud
    NATURAL RADIOACTIVITY IN EGYPTIAN AND INDUSTRIALLY USED AUSTRALIAN BAUXITES AND ITS TAILING RED MUD. N. ffiRAHIEM ' XA9953147 National Center for Nuclear Safety & Radiation Control, AEA, Cairo, Egypt T. ABD EL MAKSOUD ,B.EL EZABY , A.NADA, H.ABU ZEID . Physics Department,Women's College, Ain Shams University, Cario, Egypt Abstract Red mud is produced in considerable masses as a waste product in the production of aluminum from bauxite. It may be used for industrial or agricultural purposes. According to it's genesis by weathering and sedimentation bauxites contain high concentrations of uranium and thorium. Three Egyptian bauxites , Australian industry used buaxite and its red mud tailing were analyzed by a high resolution gamma spectrometer, with a hyper pure germanium detector. The three Egyptian bauxites show high concentrations in uranium series, and around 120 Bq kg"1 for uranium -235. K-40 concentrations for these samples ranged from 289 to 575 Bq kg"1. Thorium series concentrations show lower values. The industrially used bauxite shows very low concentrations for all radioactive nuclides. Its tailing red mud as a low level radioactive waste LLRW, shows low concentrations for uranium - series, thorium - series and also 40K, so it is recommended to be used in industrial and agricultural purposes, which is not permissible for the normal red mud. Introduction Laterites vary widely in composition, but most contain aluminum hydroxides and iron hydroxides and oxides, mixed with a little residual quartz. A rare variety called bauxite is almost pure hydrous aluminum oxide AI2O3 nH^O, and hence valuable as an ore of aluminum production. [1].
    [Show full text]
  • Fundamental Study of Red Mud Based Fluxes for Desulphurization and Dephosphorization of Hot Metal
    FUNDAMENTAL STUDY OF RED MUD BASED FLUXES FOR DESULPHURIZATION AND DEPHOSPHORIZATION OF HOT METAL by Abdolkarim Danaei B.Sc. Isfahan University of Technology, Iran, 1985 M.Sc. Sharif University of Technology, Iran, 1993 A dissertation presented to Ryerson University in partial fulfillment of the requirements for the degree of Doctor of Philosophy in the Program of Mechanical and Industrial Engineering Toronto, Ontario, Canada, 2015 © Abdolkarim Danaei, 2015 AUTHOR’S DECLARATION FOR SUBMISSION OF ELECTRONIC DISSERTATION I hereby declare that I am the sole author of this dissertation. This is a true copy of the dissertation, including any required final revisions, as accepted by my examiners. I authorize Ryerson University to lend this dissertation to other institutions or individuals for the purpose of scholarly research. I further authorize Ryerson University to reproduce this dissertation by photocopying or by other means, in total or in part, at the request of other institutions or individuals for the purpose of scholarly research. I understand that my dissertation may be made electronically available to the public. ii Abstract FUNDAMENTAL STUDY OF RED MUD BASED FLUXES FOR DESULPHURIZATION AND DEPHOSPHORIZATION OF HOT METAL Doctor of Philosophy, 2015 Abdolkarim Danaei B.Sc. Isfahan University of Technology, Iran M.Sc. Sharif University of Technology, Iran Mechanical and Industrial Engineering Ryerson University Bauxite residue, also known as red mud, is generated during alumina production and is an abundant industrial waste material. Continuously increasing environmental concerns, together with scarcity of traditional mineral resources, have created a thrust to re-use the material. Red mud contains significant amounts of iron oxide and sodium hydroxide, hence a highly basic (pH > 10) slurry.
    [Show full text]
  • Carbon Capture and Storage Realising the Potential? Energy Materials Availability Handbook Introduction
    A handbook by the Technology and Policy Assessment theme of the UK Energy Research Centre Carbon Capture and Storage Realising the potential? Energy Materials Availability Handbook Introduction Welcome to the Energy Materials Availability Handbook (EMAH), a brief guide to some of the materials that are critical components in low carbon energy technologies. In recent years concern has grown regarding the availability of a host of materials critical to the development and manufacturing of low carbon technologies. In this handbook we examine 10 materials or material groups, presenting the pertinent facts regarding their production, resources, and other issues surrounding their availability. Three pages of summary are devoted to each material or material group. A ‘how to use’ guide is provided on the following pages. The UK Energy Research Centre, which is funded by Research Councils UK, carries out world-class research into sustainable future energy systems. It is the hub of UK energy research and the gateway between the UK and the international energy research communities. Our interdisciplinary, whole systems research informs UK policy development and research strategy. Follow us on Twitter @UKERCHQ Authors Jamie Speirs Bill Gross Rob Gross Yassine Houari Selection of Materials Concern over the availability of low carbon materials is increasing, with numerous materials highlighted throughout the debate. Identifying which materials are most important is therefore a complex and potentially subjective process. To select the 10 materials presented here we first systematically reviewed the literature on materials criticality assessment, focusing on materials with particular relevance to low-carbon energy technologies. We then normalised the results of these assessments.
    [Show full text]
  • A Partial Glossary of Spanish Geological Terms Exclusive of Most Cognates
    U.S. DEPARTMENT OF THE INTERIOR U.S. GEOLOGICAL SURVEY A Partial Glossary of Spanish Geological Terms Exclusive of Most Cognates by Keith R. Long Open-File Report 91-0579 This report is preliminary and has not been reviewed for conformity with U.S. Geological Survey editorial standards or with the North American Stratigraphic Code. Any use of trade, firm, or product names is for descriptive purposes only and does not imply endorsement by the U.S. Government. 1991 Preface In recent years, almost all countries in Latin America have adopted democratic political systems and liberal economic policies. The resulting favorable investment climate has spurred a new wave of North American investment in Latin American mineral resources and has improved cooperation between geoscience organizations on both continents. The U.S. Geological Survey (USGS) has responded to the new situation through cooperative mineral resource investigations with a number of countries in Latin America. These activities are now being coordinated by the USGS's Center for Inter-American Mineral Resource Investigations (CIMRI), recently established in Tucson, Arizona. In the course of CIMRI's work, we have found a need for a compilation of Spanish geological and mining terminology that goes beyond the few Spanish-English geological dictionaries available. Even geologists who are fluent in Spanish often encounter local terminology oijerga that is unfamiliar. These terms, which have grown out of five centuries of mining tradition in Latin America, and frequently draw on native languages, usually cannot be found in standard dictionaries. There are, of course, many geological terms which can be recognized even by geologists who speak little or no Spanish.
    [Show full text]
  • Draft Letter to the Swedish Government
    EUROPEAN COMMISSION Brussels, 23.XII.2008 C(2008) 8997 PUBLIC VERSION WORKING LANGUAGE This document is made available for information purposes only. Subject: N 143/2008 – Slovak Republic ZSNP a.s. Sir, 1. PROCEDURE By letter dated 18 March 2008, registered on the same day (A/5354), the Slovak authorities notified to the Commission of the above mentioned individual ad hoc aid measure, in accordance with Article 88 (3) of the EC Treaty. The Commission asked for additional information by letters of 22 April 2008 (D/51615), 11 July 2008 (D/52763) and 19 September 2008 (D/53604). The Slovak authorities submitted the requested information by letters of 14 May 2008, registered on the same day (A/8922), 6 August 2008, registered on the same day (A/16455), 31 October 2008, registered on the same day (A/23014), 18 November 2008, registered on the same day (A/ 24606) and on 18 December 2008, registered on the same day (A/27397). 2. DESCRIPTION OF THE MEASURE 2.1 Objective The primary objective of the notified ad hoc aid measure is the remediation of an industrial site contaminated by the production of primary aluminium from bauxite ore through isolation of a mud disposal site in order to avoid seepage of rain waters through disposal site and creation of alkaline waters with pH 13.5. More specifically, the aid measure is aimed at: Commission européenne, B-1049 Bruxelles / Europese Commissie, B-1049 Brussel - Belgium. Telephone: (32-2) 299 11 11. - eliminating risks of contamination of the adjacent lands, surface and underground water by alkaline water; - significant decrease of infiltration of rain water into the mud disposal site, - ensuring the stability of mud disposal site (prevention from landfall and erosion); - eliminating dust emissions; - increase in landscape aesthetic level of the area.
    [Show full text]
  • Reductive Smelting of Red Mud for Iron Recovery
    Chemie Ingenieur Research Article 1535 Technik Reductive Smelting of Red Mud for Iron Recovery Frank Kaußen*, and Bernd Friedrich DOI: 10.1002/cite.201500067 The reductive smelting of red mud is calculated and investigated regarding the necessary amount of reduction agents and the final composition of the pig iron phase and the mineral (slag) phase as products of the process. Liquidus temperatures of slags with three different compositions are calculated during the reduction process and in dependency of the remaining sodium content in the slag. All calculations were done with FactSage and the results are confirmed by smelting experi- ments in a lab scale electric arc furnace. Keywords: Bauxite residue, Carbothermic reduction, Iron recovery, Red mud Received: June 02, 2015; revised: August 10, 2015; accepted: August 31, 2015 1 Introduction Table 1. Composition of different red muds and composition of the raw material used in the experiments. Red mud is the so-called bauxite residue after the solid- Component Average Red mud After After re-leaching liquid separation from alkaline high pressure leaching of [wt %] red mud Lu¨nen re-leaching with CaO (CaO/ aluminum bearing bauxite ore. Depending on the composi- (Germany) SiO2 ~ 0.5) tion of the primary mineral deposit, 4 – 7 t bauxite are nec- essary to gain 2 t alumina in order to produce 1 t aluminum Fe2O3 30 – 50 29.5 35.5 34.7 [1]. The leaching process is very selective on the extraction Al2O3 10 – 20 27 18.3 17.7 of aluminum and gallium and the undissolved minerals SiO 5 – 20 13.1 14.9 15 remain in the residue.
    [Show full text]
  • Technical Measures of Air Pollution Control in the Iron and Steel Industry
    COMMISSION OF THE EUROPEAN COMMUNITIES Technical measures of air pollution control in the iron and steel industry Reports and information on research work subsidized by the ECSC as at June 1968 COMMISSION OF THE EUROPEAN COMMUNITIES Technical measures of air pollution control in the iron and steel industry Reports and information on research work subsidized by the ECSC as at June 1968 Prepared by Kurt Guthmann and Gerhard Will CONTENTS Page FOREWORD 7 1. Introduction 1.1 Sources of air pollution in the iron and steel industry 9 1.2 ECSC activity in the field of air pollution control 13 1.3 Research and information groups ' 13 2. Dust and gas measurement 15 2.0 Scope and problems 15 2.1 Comparison and improvement of existing measuring instruments and methods and development of new ones ". 16 2.11 Comparison of sampling instruments and methods (Study PS 150) 16 2.12 Development of a portable dust-measuring instrument with a large air sample capacity (Study PS 139) 16 2.13 Micropore membranes (Study PS 10) 18 2.14 Research on the development of a simple method for determining free S1O2 content (Study PS 37) 18 2.15 Establishment of an international microscopic counting standard (Study PS 135) 18 2.16 Experimental electro-acoustic particle-size measurement (Study PS 141) 20 2.17 Establishing the source of dusts (Study PS 35) 22 2.18 Development of dust-measurement recording instruments (Studies PS 15 and PS 138) ... 22 2.2 Measurements of the dustiness of working areas 24 2.21 Dust survey in German steelworks (Study PS 20) 25 2.22 Dust survey in Italian steelworks (Studies PS 11 and 12) 25 2.23 Dust survey in Luxembourg steelworks (Studies PS 49 and PS 144) 26 2.24 Dust survey in Dutch foundries (Study PS 17) 27 2.3 Research on dust and gas emissions and their ground level concentration 27 2.31 Research on fluorine —and SO2 —containing waste gases discharged by steelworks (Study PS 129) 27 2.32 Detection and removal of fluorine in waste gases (Study PS 149) 28 3.
    [Show full text]