DOCSLIB.ORG

EXOTHERMIC FLUX FORGE WELDING of STEEL TUBULARS by Jeremy Joseph Iten

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
EXOTHERMIC FLUX FORGE WELDING of STEEL TUBULARS by Jeremy Joseph Iten EXOTHERMIC FLUX FORGE WELDING OF STEEL TUBULARS by Jeremy Joseph Iten Copyright by Jeremy Joseph Iten 2020 All Rights Reserved A thesis submitted to the Faculty and the Board of Trustees of the Colorado School of Mines in partial fulfillment of the requirements for the degree of Doctor of Philosophy (Materials Science). Golden, Colorado Date Signed: Jeremy Joseph Iten Signed: Dr. Michael Kaufman Thesis Advisor Golden, Colorado Date Signed: Dr. Eric Toberer Professor and Program Director Materials Science ii ABSTRACT Welding processes inevitably alter the local microstructure and in turn affect the properties. For many grades of steels that require high strength, ductility, and toughness, it is difficult to maintain this combination of properties after welding. While full part heat treatments can sometimes be used to recover the microstructure and properties, this approach is impractical for welding of tubular strings in service. Therefore, advanced welding and localized post weld heat treatment methods are needed that can economically produce high integrity welds in tubular strings while maintaining strength, ductility, and toughness property requirements. A novel exothermic flux forge welding method is introduced for solid-state welding of steel tubulars and aspects of the development are discussed including constituent and heating rate effects on self- propagating high-temperature synthesis of metal and oxide products. The exothermic flux forge welded process was investigated for solid-state welding of a high strength low alloy (HSLA) steel and American Petroleum Institute (API) Q125 grade high-strength casing with a 14-inch (355.6 mm) outer diameter and 0.866-inch (22 mm) wall thickness. Post weld heat treatment approaches, including a multi-step heat treatment that included an intercritical heating stage, were investigated on the welded steel for their effects on microstructure and properties. Welded steel performance was characterized by methods including tensile, bend, impact energy absorption, and strain life fatigue testing. Corrosion response was investigated by salt spray and by submersion in NACE Solution A. Heat affected zone microstructure and hardness were also examined along with bond plane fracture using the nick break method. The results include achievement of (1) material specified strength, ductility, and toughness requirements in welded Q125 steel and (2) demonstration of strain life fatigue mean reversals to failure in welded HSLA steel of 2.5 times higher than gas tungsten arc welded specimens. iii TABLE OF CONTENTS ABSTRACT... ................................................................................................................................ iii LIST OF FIGURES ..................................................................................................................... viii LIST OF TABLES ....................................................................................................................... xvi CHAPTER 1 INTRODUCTION .................................................................................................... 1 1.1 Background of the Problem ............................................................................................... 1 1.2 Research Questions and Hypotheses ................................................................................. 3 1.3 Importance of the Study ..................................................................................................... 5 1.4 Summary ............................................................................................................................ 6 CHAPTER 2 BACKGROUND AND REVIEW OF THE LITERATURE ................................... 7 2.1 Welding Flux Development ............................................................................................... 7 2.1.1 Introduction ............................................................................................................. 7 2.1.2 Definition ................................................................................................................. 7 2.1.3 Background .............................................................................................................. 8 2.2 Self-Propagating High-Temperature Synthesis (SHS) .................................................... 12 2.2.1 Introduction ........................................................................................................... 13 2.2.2 Background ............................................................................................................ 13 2.2.3 Reaction Thermodynamics .................................................................................... 14 2.2.4 Reaction Kinetics ................................................................................................... 17 2.2.5 Reaction synthesis related to fluxes and welding .................................................. 18 2.3 Established Welding Processes and Selected Theory ...................................................... 20 2.3.1 Weld Microstructure .............................................................................................. 21 2.4 Oil Country Tubular Goods (OCTG) Overview .............................................................. 28 iv 2.4.1 Threaded Connections Background ...................................................................... 29 2.4.2 Welded Connections Background ......................................................................... 30 2.4.3 Governing Standards ............................................................................................. 31 2.5 Introduction to Exothermic Flux Forge Welding (EFFW) .............................................. 31 2.5.1 Heating Examination ............................................................................................. 34 2.5.2 Forging Pressure .................................................................................................... 38 2.5.3 Exothermic Flux .................................................................................................... 39 2.6 Summary .......................................................................................................................... 43 CHAPTER 3 RESEARCH METHODS ....................................................................................... 44 3.1 Exothermic Investigations ............................................................................................... 44 3.2 Exothermic Flux Ring Processing ................................................................................... 47 3.3 Exothermic Flux Forge Welding Investigations .............................................................. 49 3.3.1 Small-scale exothermic flux forge welding systems ............................................. 50 3.3.2 Full-scale exothermic flux forge welding .............................................................. 53 3.3.3 Post weld heat treatment development .................................................................. 54 3.3.4 Weld testing and analysis ...................................................................................... 55 3.4 Summary .......................................................................................................................... 57 CHAPTER 4 SELF-PROPAGATING HIGH TEMPERATURE SYNTHESIS INVESTIGATIONS TOWARDS AN EXOTHERMIC FORGE WELDING FLUX ...................................................................................................................... 58 4.1 Abstract ............................................................................................................................ 58 4.2 Introduction ...................................................................................................................... 59 4.3 Materials and Methods .................................................................................................... 60 4.4 Results and Discussions ................................................................................................... 61 v 4.5 Conclusions...................................................................................................................... 76 CHAPTER 5 INVESTIGATION OF EXOTHERMIC FLUX FORGE WELDING AND POST WELD HEAT TREATMENT ON THE MICROSTRUCTURE AND PROPERTIES OF HSLA STEEL .......................................................................... 77 5.1 Abstract ............................................................................................................................ 77 5.2 Introduction ...................................................................................................................... 78 5.3 Materials and Methods .................................................................................................... 78 5.4 Results and Discussions ................................................................................................... 82 5.4.1 Tensile Results ....................................................................................................... 83 5.4.2 Bend Results .......................................................................................................... 84 5.4.3 Impact Energy ....................................................................................................... 85 5.4.4 Corrosion Testing .................................................................................................. 86 5.4.5 Strain Life Fatigue Testing ...................................................................................
Load more

Recommended publications
  • Study and Characterization of EN AW 6181/6082-T6 and EN AC
    metals Article Study and Characterization of EN AW 6181/6082-T6 and EN AC 42100-T6 Aluminum Alloy Welding of Structural Applications: Metal Inert Gas (MIG), Cold Metal Transfer (CMT), and Fiber Laser-MIG Hybrid Comparison Giovanna Cornacchia * and Silvia Cecchel DIMI, Department of Industrial and Mechanical Engineering, University of Brescia, via Branze 38, 25123 Brescia, Italy; [email protected] * Correspondence: [email protected]; Tel.: +39-030-371-5827; Fax: +39-030-370-2448 Received: 18 February 2020; Accepted: 26 March 2020; Published: 27 March 2020 Abstract: The present research investigates the effects of different welding techniques, namely traditional metal inert gas (MIG), cold metal transfer (CMT), and fiber laser-MIG hybrid, on the microstructural and mechanical properties of joints between extruded EN AW 6181/6082-T6 and cast EN AC 42100-T6 aluminum alloys. These types of weld are very interesting for junctions of Al-alloys parts in the transportation field to promote the lightweight of a large scale chassis. The weld joints were characterized through various metallurgical methods including optical microscopy and hardness measurements to assess their microstructure and to individuate the nature of the intermetallics, their morphology, and distribution. The results allowed for the evaluation of the discrepancies between the welding technologies (MIG, CMT, fiber laser) on different aluminum alloys that represent an exhaustive range of possible joints of a frame. For this reason, both simple bar samples and real junctions of a prototype frame of a sports car were studied and, compared where possible. The study demonstrated the higher quality of innovative CMT and fiber laser-MIG hybrid welding than traditional MIG and the comparison between casting and extrusion techniques provide some inputs for future developments in the automotive field.
    [Show full text]
  • Section 1 (Parts 1 - 4) of This Specification Includes Rail Welding by Electric Flash-Butt Welding Method
    SECTION 05091 RAIL WELDING NOTE: Section 1 (Parts 1 - 4) of this specification includes rail welding by Electric Flash-Butt Welding method. Section 2 (Parts 5 - 8) of this specification includes rail welding by the Thermite Rail Welding method. SECTION 1 - ELECTRIC FLASH-BUTT WELDING PART 1 - GENERAL 1.01 SECTION INCLUDES A. The work specified in this section shall include the fabrication of continuous welded rail (CWR) strings by electric flash-butt welding, including testing, inspection, and qualification of welding and welders. B. The work specified in this section shall also include movement of rail from the manufacturer to the Contractor’s welding plant, from the welding plant to the welded string storage location and from the storage location to the final placement in track location. 1.02 RELATED SECTIONS A. Section 05651- General Track Construction B. Section 05652 - Ballasted Track Construction C. Section 05653 - Direct Fixation Track Construction D. Section 05656 - Running Rail 1.03 REFERENCES A. American Railway Engineering and Maintenance-of-Way Association (AREMA) Manual for Railway Engineering, Vol. I, Chapter 4, Specification for Fabrication of Continuous Welded Rail (latest addition). B. ASTM E18 C . ASTM E709 (replaced E109) D . ASTM E94 (replaced E142) E. ASTM E164 F . ASTM E709 (duplicate) G. AWS D1.1 1X0000 (11/07) 05091 - 1 H. USNRC Rules and Regulations, Title 10, Atomic Energy, Part 20. I. ASNT SNT-TC-1A Recommended Guidelines for Qualification and Certification of Non- Destructive Testing Personnel. 1.04 SUBMITTALS A. The Contractor shall submit procedures and documentation in accordance with the Section 01300 and as follows.
    [Show full text]
  • Download/Pdf/ 71319287.Pdf (Accessed on 13 July 2020)
    metals Article Optimization of PWHT of Simulated HAZ Subzones in P91 Steel with Respect to Hardness and Impact Toughness Gorazd Lojen * and Tomaž Vuherer Faculty of mechanical engineering, University of Maribor, Smetanova ulica 17, 2000 Maribor, Slovenia; [email protected] * Correspondence: [email protected]; Tel.: +386-2-220-7864 Received: 30 July 2020; Accepted: 4 September 2020; Published: 9 September 2020 Abstract: Appropriate post weld heat treatment (PWHT) is usually obligatory when creep resistant steels are welded for thermal power plant components that operate at elevated temperatures for 30-40 years. The influence of different PWHTs on the microstructure, hardness, and impact toughness of simulated heat affected zone (HAZ) subzones was studied. Thereby, coarse grained HAZ, two different fine grained HAZ areas, and intercritical HAZ were subjected to 20 different PWHTs at temperatures 740–800 ◦C and durations 0.5–8 h. It was found that the most commonly recommended PWHT, of 3 h or less at 760 ◦C, is insufficient with respect to the hardness and impact toughness of coarse grained HAZ. To obtain a Vickers hardness 265 HV and impact toughness at least equal to ≤ the impact toughness of the base metal (192 J) in the coarse grained HAZ, it took 8 h at 740 ◦C, 4 h at 760 ◦C, more than 1 h at 780 ◦C, and 0.5 h and 800 ◦C. Even after 8 h at 800 ◦C, mechanical properties were still within the target range. The most recommendable post weld heat treatments at 780 ◦C for 1.2–2 h or at 760 ◦C for 3–4 h were identified.
    [Show full text]
  • General Disclaimer One Or More of the Following Statements May Affect This Document
    General Disclaimer One or more of the Following Statements may affect this Document This document has been reproduced from the best copy furnished by the organizational source. It is being released in the interest of making available as much information as possible. This document may contain data, which exceeds the sheet parameters. It was furnished in this condition by the organizational source and is the best copy available. This document may contain tone-on-tone or color graphs, charts and/or pictures, which have been reproduced in black and white. This document is paginated as submitted by the original source. Portions of this document are not fully legible due to the historical nature of some of the material. However, it is the best reproduction available from the original submission. Produced by the NASA Center for Aerospace Information (CASI) MASSACHUSETTS INSTITUTE OF TEC'.-INOLOGY DEPARTMENT OF OCEAN ENGINEERING SEP 83 CAMBRIDGE. MASS. 02139 RECEIVED FAVUV wrw STI DEPI- , FINAL REPORT "Wo Under Contract No. NASW-3740 (M.I.T. OSP #93589) ON FEASIBILITY OF REMOTELY MANIPULATED WELDING IN SPACE -A STEP IN THE DEVELOPMENT OF NOVEL JOINING TECHNOLOGIES- Submitted to Office of Space Science and Applications Innovative Utilization of the Space Station Program Code E NASA Headquarters Washington, D.C. 20546 September 1983 by Koichi Masubuchi John E. Agapakis Andrew DeBiccari Christopher von Alt (NASA-CR-1754371 ZEASIbILITY CF RZ,1JTL": Y `84-20857 MANIPJLATED WELLINu iN SPAI.E. A STEP IN THE Uc.Y1;LuPdENT OF NUVLL Ju1NING Tkk ;HNuLUGIES Final Peport (c;dssachu6etts Irist. or Tccli.) U11CIds ibJ p HC Al2/Mk AJ 1 CSCL 1jI G:i/.i7 OOb47 i i rACKNOWLEDGEMENT The authors wish to acknowledge the assistance provided by M.I.T.
    [Show full text]
  • Mechanical Testing and Evaluation of High-Speed and Low
    MECHANICAL TESTING AND EVALUATION OF HIGH-SPEED AND LOW- SPEED FRICTION STIR WELDS A Thesis by Nitin Banwasi Bachelor of Engineering, Bangalore University, Bangalore, India 2000 Submitted to the College of Engineering and the faculty of the Graduate School of Wichita State University in partial fulfillment of the requirements for the degree of Master of Science Fall 2005 EXPERIMENTAL TESTING AND EVALUATION OF HIGH-SPEED AND LOW- SPEED FRICTION STIR WELDS I have examined the final copy of this thesis for form and content and recommend that it be accepted in partial fulfillment of the requirements for the degree of Master of Science, with a major in Mechanical Engineering. George E. Talia, Committee Chair We have read this thesis and recommended its acceptance: Dr. Hamid M. Lankarani, Department Chair, Committee Member Dr. Krishna K. Krishnan, Committee Member ii DEDICATION To My Parents iii ACKNOWLEDGEMENTS I am grateful to all that are part of my efforts during my work both academically and personally. I am thankful to my committee chair, Dr.George E.Talia, for being not only supportive in my endeavors but also patient and informative. I appreciate the involvement of both Dr. Hamid M. Lankarani and Dr. Krishna K. Krishnan for their involvement in its fulfillment. I also want to remember fellow student’s help and suggestions in making it possible with gratitude. iv ABSTRACT The potential of the Friction Stir Welding (FSW) process is easily observed in the creation of defect free welds in almost all of the Aluminum alloys. The success and applicability of the process, however, will depend on the performance of the welds compared to other joining processes.
    [Show full text]
  • The Right Tool for Every Job...Big Or Small
    The right tool for every job.... big or small TRANSMIG MULTI-PROCESS WELDING INVERTERS The CIGWELD complete range of TRANSMIG multi-process MIG, Stick & TIG welding inverters, come loaded with features sure to satisfy any trade professional in any industry regardless of the welding application. 1300 654 674 I www.cigweld.com.au Sponsors Index Shindaiwa Structural Steel Standards 2 http://www.shindaiwa.com.au/ South Pacific Welding Group Pressure Equipment 6 http://www.spwgroup.com.au/home.asp Standards Smenco http://www.smenco.com.au Thermadyne – Transmig 9 Thermadyne - Cigweld Range www.thermadyne.com.au SafeTac Company Bio – Boston 11 http://www.safetac.com.au Engineering Bureau Veritas http://www.bureauveritas.com.au Smenco – Mining Spec 13 Southern Cross Industrial Welder Supplies http://www.scis.com.au 1300 Apprentice 15 Technoweld http://www.technoweld.com.au MSA - Australian Government 16 Hardface Technologys Skills Connect http://www.hardface.com.au 3834 Weld Management Letter to the Editor 18 [email protected] Welding Duplex – Lincoln 19 Cover Page Electric CIGWELD have released a complete family of six Transmig 3‐in‐1 MIG, STICK and TIG welding inverters to Progress Update 20 the market, ranging from 175 Amps right up to 550 Amps. In November 2011, the Transmig 200i and Transmig 250i single phase portable Multi‐Process Inverters with power factor correction (PFC) hit the market and created quite a stir, and now in early 2012 CIGWELD have realised the 3 phase versions to complete the Transmig inverter range. AWI operates this service for members. Information and comments in AWI publications are the opinions of specific individuals and companies, and may not reflect the position of AWI or its Directors.
    [Show full text]
  • Welding Operations
    WELDING OPERATIONS Date Initiated: February 1, 1993 Dates Modified / Updated: September 15, 1993 October 16, 1998 PROCESS DESCRIPTION: Many industrial and manufacturing facilities regularly use a variety of welding processes and materials. The processes include; - Gas Metal Arc Welding (GMAW) - a. k. a. Metal Inert Gas Welding (MIG), - Gas Tungsten Arc Welding (GTAW) - a. k. a. Tungsten Inert Gas Welding (TIG), - Shielded Metal Arc Welding (SMAW) - a. k. a. Manual Metal Arc Welding (MMA), - Flux Core Arc Welding (FCAW), - Submerged Arc Welding (SAW), - Arc Spot Welding, - Electrogas Welding, - Electrostag Welding, - Brazing, - Thermal Cutting, - Resistance Welding, - Plasma Arc Welding, - Electron Beam Welding, - Laser Beam Welding The majority of the common welding processes can be classified as either gas metal arc welding (GMAW) or shielded metal arc welding (SMAW). GMAW generally uses an electrical current to melt and apply a filler metal under a blanket of inert gas. SMAW traditionally uses an electrical current to melt specially coated electrodes which form a protective flux over the weld during application. Both processes use electrodes, filler metals, wire, coatings, and/or gases that may contain and emit several listed substances including NOx, CO, cadmium, cobalt, copper, chromium, manganese, nickel, lead, zinc, and fluorides. Welding operations release fumes and particulates with diameters of 0.001 to 100 microns. Previous studies of welding emissions have been primarily focused on worker exposure and safety. Many technical difficulties have been identified regarding proper sampling and analytical procedures due, in part, to the wide variety of processes, welding materials, and field conditions. The majority of existing test data which can be used to quantify welding emissions is based on studies performed by the American Welding Society (AWS).
    [Show full text]
  • Guidelines for the Welded Fabrication of Nickel-Containing Stainless Steels for Corrosion Resistant Services
    NiDl Nickel Development Institute Guidelines for the welded fabrication of nickel-containing stainless steels for corrosion resistant services A Nickel Development Institute Reference Book, Series No 11 007 Table of Contents Introduction ........................................................................................................ i PART I – For the welder ...................................................................................... 1 Physical properties of austenitic steels .......................................................... 2 Factors affecting corrosion resistance of stainless steel welds ....................... 2 Full penetration welds .............................................................................. 2 Seal welding crevices .............................................................................. 2 Embedded iron ........................................................................................ 2 Avoid surface oxides from welding ........................................................... 3 Other welding related defects ................................................................... 3 Welding qualifications ................................................................................... 3 Welder training ............................................................................................. 4 Preparation for welding ................................................................................. 4 Cutting and joint preparation ...................................................................
    [Show full text]
  • Magnetically Impelled Arc Butt (MIAB) Welding of Chrome Plated Steel
    MAGNETICALLY IMPELLED ARC BUTT (MIAB) WELDING OF CHROMIUM- PLATED STEEL TUBULAR COMPONENTS UTILIZING ARC VOLTAGE MONITORING TECHNIQUES DISSERTATION Presented in Partial Fulfillment of the Requirements for the Degree Doctor of Philosophy in the Graduate School of The Ohio State University By David H. Phillips, M.S.W.E ***** The Ohio State University 2008 Dissertation Committee: Professor Charley Albright, Advisor Approved by Professor Dave Dickinson _________________________________ Professor John Lippold Advisor Welding Engineering Graduate Program ABSTRACT Magnetically Impelled Arc Butt (MIAB) welding is a forge welding technique which generates uniform heating at the joint through rapid rotation of an arc. This rotation results from forces imposed on the arc by an external magnetic field. MIAB welding is used extensively in Europe, but seldom utilized in the United States. The MIAB equipment is robust and relatively simple in design, and requires low upset pressures compared to processes like Friction welding. In the automotive industry, tubular construction offers many advantages due to the rigidity, light weight, and materials savings that tubes provide. In the case of automotive suspension components, tubes may be chromium-plated on the ID to reduce the erosive effects of a special damping fluid. Welding these tubes using the MIAB welding process offers unique technical challenges, but with potential for significant cost reduction vs. other welding options such as Friction welding. Based on published literature, this research project represented the first attempt to MIAB weld chromium-plated steel tubes, and to utilize voltage monitoring techniques to assess weld quality. ii Optical and SEM microscopy, tensile testing, and an ID bend test technique were all used to assess the integrity of the MIAB weldments.
    [Show full text]
  • An Analysis of the Metal Finds from the Ninth-Century Metalworking
    Western Michigan University ScholarWorks at WMU Master's Theses Graduate College 8-2017 An Analysis of the Metal Finds from the Ninth-Century Metalworking Site at Bamburgh Castle in the Context of Ferrous and Non-Ferrous Metalworking in Middle- and Late-Saxon England Julie Polcrack Follow this and additional works at: https://scholarworks.wmich.edu/masters_theses Part of the Medieval History Commons Recommended Citation Polcrack, Julie, "An Analysis of the Metal Finds from the Ninth-Century Metalworking Site at Bamburgh Castle in the Context of Ferrous and Non-Ferrous Metalworking in Middle- and Late-Saxon England" (2017). Master's Theses. 1510. https://scholarworks.wmich.edu/masters_theses/1510 This Masters Thesis-Open Access is brought to you for free and open access by the Graduate College at ScholarWorks at WMU. It has been accepted for inclusion in Master's Theses by an authorized administrator of ScholarWorks at WMU. For more information, please contact [email protected]. AN ANALYSIS OF THE METAL FINDS FROM THE NINTH-CENTURY METALWORKING SITE AT BAMBURGH CASTLE IN THE CONTEXT OF FERROUS AND NON-FERROUS METALWORKING IN MIDDLE- AND LATE-SAXON ENGLAND by Julie Polcrack A thesis submitted to the Graduate College in partial fulfillment of the requirements for the degree of Master of Arts The Medieval Institute Western Michigan University August 2017 Thesis Committee: Jana Schulman, Ph.D., Chair Robert Berkhofer, Ph.D. Graeme Young, B.Sc. AN ANALYSIS OF THE METAL FINDS FROM THE NINTH-CENTURY METALWORKING SITE AT BAMBURGH CASTLE IN THE CONTEXT OF FERROUS AND NON-FERROUS METALWORKING IN MIDDLE- AND LATE-SAXON ENGLAND Julie Polcrack, M.A.
    [Show full text]
  • Part 2, Materials and Welding
    RULE REQUIREMENTS FOR MATERIALS AND WELDING 2002 PART 2 American Bureau of Shipping Incorporated by Act of Legislature of the State of New York 1862 Copyright 2001 American Bureau of Shipping ABS Plaza 16855 Northchase Drive Houston, TX 77060 USA Rule Change Notice (2002) The effective date of each technical change since 1993 is shown in parenthesis at the end of the subsection/paragraph titles within the text of each Part. Unless a particular date and month are shown, the years in parentheses refer to the following effective dates: (2000) and after 1 January 2000 (and subsequent years) (1996) 9 May 1996 (1999) 12 May 1999 (1995) 15 May 1995 (1998) 13 May 1998 (1994) 9 May 1994 (1997) 19 May 1997 (1993) 11 May 1993 Listing by Effective Dates of Changes from the 2001 Rules EFFECTIVE DATE 1 January 2001 (based on the contract date for construction) Part/Para. No. Title/Subject Status/Remarks 2-1-1/15.1 Permissible Variations in To clarify that mill scale is to be considered when the Dimensions – Scope plate is produced for compliance with the specified under tolerance Section 2-4-4 Piping To align ABS requirements with IACS UR P2 regarding fabrication of piping and non-destructive examinations, and to outline the requirements for the heat treatment of piping. This Section is applicable only to piping for installation on vessels to be built in accordance with the Rules for Building and Classing Steel Vessels. ii ABS RULE REQUIREMENTS FOR MATERIALS AND WELDING . 2002 PART 2 Foreword For the 1996 edition, the “Rules for Building and Classing Steel Vessels – Part 2: Materials and Welding” was re-titled “Rule Requirements for Materials and Welding – Part 2.” The purpose of this generic title was to emphasize the common applicability of the material and welding requirements in “Part 2” to ABS-classed vessels, other marine structures and their associated machinery, and thereby make “Part 2” more readily a common “Part” of the various ABS Rules and Guides, as appropriate.
    [Show full text]
  • Material Modelling for Simulation of Heat Treatment
    2003:07 LICENTIATE THESIS Material Modelling for Simulation of Heat Treatment Henrik Alberg Licentiate Thesis Department of Applied Physics and Mechanical Engineering Division of Computer Aided Design 2003:07 - ISSN: 1402-1757 - ISRN: LTU-LIC--03/07--SE II Preface This research has been carried out at Computer Aided Design at Luleå University of Technology in close cooperation with Volvo Aero in Trollhättan, where my workplace is. I would like to thank my supervisor Professor Lars-Erik Lindgren for all discussions, the critical review of my work and for your great enthusiasm. Thank you Lars-Erik! I would also like to thank Dr. Henrik Runnemalm at Volvo Aero who has made it possible for me to work in Trollhättan and for the discussion and advises. Thank you Henrik! Daniel Berglund, my colleague and co-author for two papers. Thank you Daniel for the encouragement in the beginning of my research, the discussions, advises and nevertheless all the laughs! The financial support has been provided by the MMFSC1-project a European Union funded project within the 5th framework and Luleå University of Technology. All are gratefully acknowledge. My daily work has been carried out at the division of Advanced Manufacturing Technology at Volvo Aero. I would like to thank all persons at the division for a good working environment and for sharing the your knowledge in many different areas. A special thanks to the simulation group for the many good discussions and ideas. Finally but not the less I would like to thank my girlfriend Viktoria Rönnqvist for all encouragement, happiness and for just being you.
    [Show full text]