Caution Genuine Parts Installation Instructions
Total Page:16
File Type:pdf, Size:1020Kb
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: SPLASH GUARDS APPLICATION: Q70 PART NUMBER: F38E0-1MAxx (xx Designates color) KIT CONTENTS: Item Qty. Description Service Part Number A 1 Splash guard - Front Right F3854-1MExx B 1 Splash guard - Front Left F3855-1MExx C 1 Splash guard - Rear Right G8812-1MExx D 1 Splash guard - Rear Left G8813-1MExx E 4 Tapping screw M5×25mm --- F 4 Tapping screw M5×15mm --- G 4 Spring nut --- H 4 Clip --- I 1 Paper template A --- J 1 Paper template B --- K 1 Paper template C --- L 1 Installation Instructions Replacement Template --- A B C D E FG H I J K L TOOLS REQUIRED: ٨90% or greater alcohol Socket & Driver 10mm ٨ Phillips head short Screwdriver ٨ Clean, Lint-Free Wiping Cloth ٨ Masking Tape ٨ Center Punch/Awl ٨ Mild soap / water mixture ٨ Clip remover ٨ Drill ٨ (Drill Bit(3mm(1/8inch), 6mm(1/4inch), and 8mm(5/16inch ٨ PRE-INSTALLATION WARNING, CAUTIONS CRITICAL STEPS, and NOTES: .Dealer installation Recommended ٨ .These instructions are for left side of vehicle; same procedure applies to right side ٨ .For the right side installation, use the template with the text facing the vehicle ٨ .Jack up vehicle using instructions under "Changing Tire" section of owner's manual ٨ CAUTION (Install the splash guards when the ambient temperature is above 60qF (15͠ ٨ .Do not wash or expose the vehicle to a wet environment for 24 hours after installing splash guards ٨ Page 1 of 6 F38E0 1MAxx II Rev. 8/12/13 INSTALLATION PROCEDURE: Fig 1 Front fender Front Side sill View 㱍 1) Fold tabs of template A. View 㱍(Bottom View) Fig 2 2) Align template A to underside of side sill and apply Fold tabs Align to end masking tape to hold template A in place. 䇭䇭䇭of side sill 3) Mark hole position (+) with center punch. Template A 4) Slowly remove masking tape and template A. (reuse) NOTE: Fold tabs Side sill Be sure not to damage template during removal, as it will be required for right side installation. Mark with center punch Front Fig 3 5) If needed, Jack up vehicle to drill hole. 6) Wrap masking tape around 3mm (1/8") and 8mm Drill bit Side sill (5/16") drill bits, approximately 10mm from tip. 7) Drill 3mm (1/8") 㸢 8mm (5/16") hole at marked locations on side sill. Approx. 10mm Masking tape 3mm 㸢 8mm Drill (1/8" 㸢 5/16") Fig 4 8) Remove and discard screws (2 locations) that attach Fender protector Front fender side sill. 9) Clean any dirt and oil off of installation surface with Side sill mild soap / water mixture. 10) Using a clean, lint free cloth, wipe tape area with 90% or greater alcohol. Vehicle screws Clean (discard) Page 2 of 6 F38E0 1MAxx II Rev. 8/12/13 INSTALLATION PROCEDURE: Fig 5 11) Remove approximately 20mm of tape liner from Front Tape liner double-sided tape on front splash guard in direction shown by arrow. 12) Fold tape liner pull tabs onto front splash guard surface and apply masking tape to ensure that pull Tape liner tabs are accessible. Front Masking tape Tapping screw E Fig 6 13) Align front splash guard to side sill and loosely (M5X25 E,supplied) install tapping screws E. 14) Install clip H. Front splash guard B Clip H(supplied) Fig 7 15) Lift up front splash guard. Tapping screw E 16) Tighten upper tapping screw E. NOTE: Do not over tighten screw. Reference tightening torque: 3.8䌾4.4N䊶m (34 䌾39in䊶lb) Lift up Fig 8 17) Pull out on bottom of front splash guard. 18) Tighten middle tapping screw E. NOTE: Do not over tighten screw. Tapping screw E Reference tightening torque: 3.8䌾4.4N䊶m (34 䌾39in䊶lb) Pull out Page 3 of 6 F38E0 1MAxx II Rev. 8/12/13 INSTALLATION PROCEDURE: Fig 9 19) Push rearward on bottom of splash guard. 20) Remove tape liner in direction shown by arrow and apply at least 15lbs of pressure to front splash guard B to ensure proper tape adhesion. Remove liner NOTE: and push 䍃Be sure no gap occurs between vehicle body parts and splash guard. 䍃Apply at least 15lbs or more of pressure to the front splash guard surface. Push Fig 10 Front View 㱎 Rear bumper View 㱏 Front Fig 11 21) Remove bottom fascia screws that attach rear bumper. Rear bumper NOTE: Be careful not to lose the screws. Keep to reuse. Vehicle screws (reuse) View 㱎 Fig 12 22) Fold tabs of template B. Fold tab Front 23) Align template B to rear bumper and apply masking Align to inside tape to hold template B in place. edge of rear bumper 24) Mark hole positions (+) with center punch. Mark with 25) Slowly remove masking tape and template B. center punch NOTE: Be sure not to damage template during Fold tabs Template B removal, as it will be required for right side (reuse) installation. Rear bumper Page 4 of 6 F38E0 1MAxx II Rev. 8/12/13 INSTALLATION PROCEDURE: 26) Fold tabs of template C. View 㱏 Fig 13 Front 㩿㪙㫆㫋㫋㫆㫄㩷㫍㫀㪼㫎㪀 27) Align template C to underside of rear bumper and apply masking tape to hold template C in place. Align to inside edge 28) Mark hole position (+) with center punch. of rear bumper Fold tabs 29) Slowly remove masking tape and template C. NOTE: Template C Be sure not to damage the template during Fold tabs (reuse) removal, as it will be required for right side Mark with installation. center punch Rear bumper Fig 14 30) Wrap masking tape around 3mm (1/8"), 6mm (1/4") and 8mm (5/16") drill bits, 3mm 㸢 6mm approximately 10mm from tip. (1/8" 㸢 1/4") 31) Pull rear bumper outward to drill holes. 32) Drill 3mm (1/8") 㸢 6mm (1/4") holes at marked locations of wheelhouse area on rear bumper. Drill Drill bit 33) Drill 3mm (1/8") 㸢 8mm (5/16") holes at marked Drill locations of underside area on the rear bumper. Approx. 10mm Masking 3mm 㸢 8mm tape (1/8" 㸢 5/16") Fig 15 34) Install M5 spring nuts G over 6mm (1/8") holes in Spring nuts G (supplied) rear bumper wheelhouse area. Clean NOTE: Install spring nuts(supplied) with flat edge on outside of rear bumper. 35) Clean any dirt and oil off of installation surface with mild soap / water mixture. 36) Using a clean, lint free cloth, wipe tape area with Front 90% or greater alcohol. 37) Reinstall previously removed vehicle screws. Vehicle screws (reuse) Fig 16 38) Remove approximately 20mm of tape liner from Front Tape liner double-sided tape on rear splash guard in direction shown by arrow. 38) Fold tape liner pull tabs onto rear splash guard surface and apply masking tape to ensure that pull tabs are accessible. Tape liner Masking tape Front Page 5 of 6 F38E0 1MAxx II Rev. 8/12/13 INSTALLATION PROCEDURE: 39) Align rear splash guard to rear bumper and loosely Fig 17 Tapping screw F install tapping screws F (M5x15). (M5x15,supplied) 40) Install clip H. Rear splash guard D Clip H (supplied) Fig 18 41) Lift up rear splash guard. Tapping screw F 42) Tighten upper tapping screw F. NOTE: Do not over tighten screw. Reference tightening torque: 3.8䌾4.4N䊶m (34 䌾39in䊶lb) Lift up Fig 19 43) Pull out on bottom of rear splash guard. 44) Tighten middle tapping screw F. NOTE: Do not over tighten screw. Reference tightening torque: 3.8䌾4.4N䊶m Tapping screw F (34 䌾39in䊶lb) Pull out Fig 20 45) Push rearward on bottom of rear splash guard. 46) Remove tape liner in direction shown by arrow and Remove liner apply at least 15lbs of pressure to rear splash guard and push to ensure proper tape adhesion. NOTE: 䍃Be sure no gap occurs between vehicle body parts and splash guard. 䍃Apply at least 15lbs or more of pressure to the front splash guard surface. Push FINAL INSPECTION Verify all clips are fully engaged and locked. Page 6 of 6 F38E0 1MAxx II Rev. 8/12/13.