DOCSLIB.ORG

Plank and Wood Molding Wainscoting System

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Plank and Wood Molding Wainscoting System Designer Wall Systems Plank and Wood Molding Wainscoting System Extraordinary Secondary Space Solutions. 2 Plank Secondary Space Solutions Marlite PlankTM and Wood Molding is the industry’s only interlocking wainscot system that includes everything required for a fast, reliable and beautiful installation. Marlite PlankTM is a 16” wide tongue and groove wall surfacing product available in over forty finish options – including woodgrains, textures and abstract prints. Panels are glued to a subwall and fit easily together into any of our Wood Molding profiles, stained or painted to harmonize or accent the wall. Whether in wainscot application or full wall height, Marlite Plank and Wood Molding affords designers numerous choices and builders hassle-free installation. 2 Marlite Plank and Wood Molding A total wall system that includes everything required for convenient installations. Marlite Plank is a 16” wide tongue and groove wall surfacing product available in over forty durable finishes. The Marlite Plank and Wood Molding system is pre-finished, providing color variation control and eliminating the need for job-site finishing. 3 Plank & Molding Systems The Marlite Plank and Molding system includes panels, wood molding and trim and adhesive – all pre-finished and packaged together, eliminating the need for multiple sourcing and job-site finishing. Features • 16” wide panels are easy to handle, easy to fabricate and produce minimal waste. • High Density Fiberboard (HDF) core provides outstanding durability and moisture resistance. • Pre-finished panel ensures color variation control and eliminates the need for jobsite sanding, staining or painting. • Tongue and groove joinery creates an inconspicuous joint when used in conjunction with scorelines and requires no visual fasteners. • Wood Molding includes chamfered rabbet profiles making them easy to apply and mistake-proof. • Panel Dimension 16” x 8’ x ¼” nominal 4 Marlite Plank decorative wall panel systems. Easy to install, eliminates job-site finishing for cost-effective, commercial interior design. Marlite’s Hassle Free application. Apply adhesive to panel back and adhere to subwall. Clips secure panels, ensuring inconspicuous joints. Chamfered Chamfered Chair Rail Base Molding 5 Plank Finishes Faux Woodgrains 812-S4 Aged Cherry 925-S4 Autumn Cherry 791-S4 Wild Cherry 463-S4 Eastern Walnut 201-S4 Somerset Oak 202-S4 Lancaster Oak 323-S2 Plantation Oak 324-S2 Laredo Oak 329-S2 Novato Oak 317-S4 Alum Rock Maple 360-S4 Cocoa Maple 310-S4 Sierra Maple The Exclusive Marlite Finish is a richly detailed and easy-to-maintain Melamine • surface that is more economical than decorative laminates. The base Durability Coat coat, precision coat, print coats and melamine top coat are all applied • • Print Coats to the most select substrate. Each panel is then baked, creating a tough, • Precision Coat durable finish that is easy to maintain. A diverse selection of incredibly • Base Coat realistic and richly detailed woodgrains, textures and abstract prints • Skin Coat provides consistency in color and pattern. Select • Substrate 6 Actual product will vary. Please contact us for samples. Faux Woodgrains 038 Georgetown Anigre 148 Monticello Anigre 149 Montclair Anigre 318 Windsor Anigre 319 Whittier Anigre 716-S4 Tropical Mahogany 715-S4 Mahogany 941 Laurel 942 Rosa 943 Tulip 940 Holly 944 Heartwood Custom Capabilities If you desire a different finish than our selection, simply submit your color/pattern sample and we’ll send you a lab sample match within a few days. Minimum production order quantities and lead times apply. Actual product will vary. Please contact us for samples. 7 Abstract Prints 930 Cilantro 931 Ginger 932 Juniper 933 Peppercorn 934 Saffron 192 Laramie 193 Rawlins 194 Cody 195 Saratoga 197 Walcott 781-G88 Coral Sand 782-G88 Dapple 8 Actual product will vary. Please contact us for samples. Solid Colors & Textures 5440-S2 Quiescent White 5446-S2 Morning Haze 5447-S2 Fresco 208 Abela 209 Adara 210 Aviva 211 Grizel 212 Malina 935 Menta 936 Milan 937 Sorrento Marlite has created a new line of textured surface finishes to add another dimension to your projects. Feel the fine woven textures from the beautiful Linen Series; Grizel, Aviva, Malina, Abela or Adara. Or enjoy the authentic texture of the fantastic Stone Series; Menta, Milan, Sorrento, Verona or Tuscany. 938 Tuscany 939 Verona Actual product will vary. Please contact us for samples. 9 Accessories Wood Molding Finishing Standard Molding Chamfered Profile WG 477 Single WG 475 Single WG 474 Double WG 474 Double Chair Rail and Rabbet Chair Rail Rabbet Chair Rail Rabbet Chair WG 1261 Base and WG 1261 and WG 1261 Base Rail, WG 475 Molding stained Base Molding Molding painted to Single Rabbet to match. stained match. Chair Rail used as to match. cap and WG 1261 Base Molding stained to match. Aluminum Trim 8’ lengths. Aluminum trim with factory finish to harmonize with Marlite Plank. 1110 Wood Molding Wood Molding Species – maple, oak and poplar Wood Molding is 8’ – 10’ random lengths, up to 10% of total shipment will be 4’ – 8’ random lengths Standard Molding Chamfered Profile Base Molding Corner Molding Edge Molding C-375 Marlite Construction Adhesive A strong, flexible, moisture-resistant, all-purpose adhesive formulated for fast, easy application. This adhesive is an excellent choice for use over many non-porous surfaces. Synthetic rubber base remains pliable to compensate for movement of structural surface up to 1/8”. Size: 3.5 gallon can. 12 A fast, reliable and Plank beautiful total TM wall system Physical Properties and Test Results Meets AHA and ANSI standards for prefinished paneling. Property Standard Plank F/T Plank Adhesion ASTM D3002 <5% removed <5% removed Thickness Swell ASTM D1037 12% 14% Heat Resistance AHA/ANSI A 135.5 Pass Pass Scrape Adhesion ASTM D2197 8 KG 5KG Washability AHA/ANSI A 135.5 Pass Pass Cleanbility NEMA LD3 Total Score 9 Total Score 9 Stain Resistance NEMA LD3 No Effect No Effect Fire/Flame ASTME84-04 100 25 Fire/Smoke ASTME84-04 200 200 Dover, Ohio 44622 • 800-377-1221 • www.marlite.com • [email protected] Form No. PK41-10081 Effective Date 11/15/08 Printed in U.S.A. Marlite is committed to protecting our environment and sustaining resources for future generations. Printed on Recycled Paper.
Load more

Recommended publications
  • PANELING DOORS OR OTHER WOOD WORK, No
    (No Model.) J. A. SMITH, PANELING DOORS OR OTHER WOOD WORK, No. 422,844, Patented Mar. 4, 1890, Zze 7/2Zealafae Z7ez/622227 2222222, (22%afzezzé, UNITED STATES PATENT OFFICE. JOHN A. SMITH, OF ROCHESTER, NEW YORK. PAN ELING DOORS oR OTHER WOOD-WORK. or: SPECIFICATION forming part of Letters Patent No. 422,844, dated March 4, 1890. Application filed August 15, 1889, Serial No, 320,824 (No model.) To all whom, it may concern: In consequence of the prior construction Be it known that I, JoHN A. SMITH, a citi the contraction or shrinkage of the panel Zen of the United States, residing at Roches draws the moldings and nails outward from 5o ter, in the county of Monroe and State of New the grooved part of the frame, as indicated York, have invented new and useful Improve at the right-hand side of the frame shown. ments in Paneling Doors or other Wood This is a very objectionable feature, to which Work, of which the following is a specifica all Wooden doors having panels and mold tion. ings around the panels are subject; and to This invention relates to paneling wood avoid this objection I provide the frame 1, 55 O work where the panel edges are secured by Fig. 2, which may represent the stiles of a moldings and nails, as in doors. door, with a rabbet 2 at each edge to form a The object of my invention is to avoid in central projecting tongue 3. The moldings serting the panel-edges in grooves cut in the 4, of any desired pattern or style, are fash surrounding frame, and to provide a novel ioned to set in the rabbets against the sides construction and means for so securing the of the tongue, where such moldings are Se panels and moldings that expansion and con cured by glue and by obliquely-driven nails traction of the panels will not disturb the 5, that pass into the solid parts of the stile or moldings, and whereby a new panel can be frame 1.
    [Show full text]
  • Build a Plane That Cuts Smooth and Crisp Raised Panels With, Against Or Across the Grain – the Magic Is in the Spring and Skew
    Fixed-width PanelBY WILLARD Raiser ANDERSON Build a plane that cuts smooth and crisp raised panels with, against or across the grain – the magic is in the spring and skew. anel-raising planes are used Mass., from 1790 to 1823 (Smith may to shape the raised panels in have apprenticed with Joseph Fuller doors, paneling and lids. The who was one of the most prolific of the profile has a fillet that defines early planemakers), and another similar Pthe field of the panel, a sloped bevel example that has no maker’s mark. to act as a frame for the field and a flat Both are single-iron planes with tongue that fits into the groove of the almost identical dimensions, profiles door or lid frame. and handles. They differ only in the I’ve studied panel-raising planes spring angles (the tilt of the plane off made circa the late 18th and early 19th vertical) and skew of the iron (which centuries, including one made by Aaron creates a slicing cut across the grain to Smith, who was active in Rehoboth, reduce tear-out). The bed angle of the Smith plane is 46º, and the iron is skewed at 32º. Combined, these improve the quality of cut without changing the tool’s cutting angle – which is what happens if you skew Gauges & guides. It’s best to make each of these gauges before you start your plane build. In the long run, they save you time and keep you on track. Shaping tools. The tools required to build this plane are few, but a couple of them – the firmer chisel and floats – are modified to fit this design.
    [Show full text]
  • Simple & Fast Rabbeted Drawers
    Simple & Fast Rabbeted Drawers It takes only one setup on the table saw to cut every joint you need to make a solid drawer. Without a doubt, this is as easy as it gets. Alonglong thethe rroadoad ttoo ccomfortablyomfortably rreferringeferring ttoo yourself as a “woodworker,” there are a few im- portant milestones you must reach. One of these is building your fi rst drawer. For some reason, this project causes more antacid-popping than almost any other project. A drawer is just a box. The tricky part is that the box must fi t accurately into a hole and move smoothly. There are three steps to a successful drawer: precise measuring, accurate joining and careful fi tting. This article shows you the tricks we use to successfully complete all three steps. Measuring Like a Pro Let’s say you’re building an end table with a drawer. Knowing the size of the drawer’s hole is the fi rst critical piece of information. Seeing how that space is made and understanding how the drawer will “run” in the table is the next step. In traditional case construction, the drawer is just slightly smaller than its hole (which is the tech- nique we’re showing here). In modern cabinets, the drawer is considerably smaller than its hole to make room for mechanical slides or glides. In our traditional case, the drawer hole must be clear of obstructions or corners that the drawer PARRISHAL BY PHOTO can hang up on. For that reason, the sides of the drawer are traditionally kept in check by “drawer guides,” which are simply pieces of wood inside “inset drawer,” which means the drawer front the drawer to fi t the space exactly and then trim it the carcase that are parallel to the sides of the doesn’t have a lip that covers the gap between the down with a hand plane to allow for proper move- drawer.
    [Show full text]
  • Assembly Instructions
    Cabinet Assembly Instructions Revised 10/1/2018 Page 1 IMPORTANT DISCLAIMER: These instructions demonstrate the generally recommended process for assembling cabinets purchased from the cabinet bar. The instructions demonstrate the basic parts and processes for several types of cabinets, but we do not provide specific instructions for each of the hundreds of possible choices. You, as the assembler, must identify the set of instructions that most closely applies. Assembly is not complicated, but common sense and thoughtful planning is required before getting started. Familiarize yourself with the parts and your tools before beginning assembly. Check each piece for shipping damage or manufacturing errors before attaching it. Check each finished piece for color match (with other finished pieces in the order) before attaching it. We take pains to produce and package these products in a way that minimizes warping, twisting or other damage, but there is no way to guarantee that it will not happen. Small amounts of warpage can typically be managed in the assembly process with the assistance of clamps and/or other tools. If you find pieces that have become more severely warped or twisted in transit, please photograph them and report this to Customer Service before beginning assembly of that cabinet. BEFORE YOU BEGIN: We have video(s) available on thecabinetbar.com which serve as a good overview of the assembly process. We strongly recommend that you start there before reading these instructions. INTRODUCTION – Guidelines for Assembly These cabinets are assembled using pre‐inserted splines along with glue (not provided) and pins or staples (not provided). Clamping is optional.
    [Show full text]
  • Operating Instructions and Parts Manual 6-Inch Woodworking Jointer Models JJ-6CSDX, JJ-6HHDX
    Operating Instructions and Parts Manual 6-inch Woodworking Jointer Models JJ-6CSDX, JJ-6HHDX JET 427 New Sanford Road LaVergne, Tennesseee 37086 Part No. M-708457DX Ph.: 800-274-6848 Revision D1 06/2019 www.jettools.com Copyright © 2018 JET 1.0 IMPORTANT SAFETY INSTRUCTIONS WARNING – To reduce risk of injury: 1. Read and understand the entire owner's manual before attempting assembly or operation. 2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury. 3. Replace the warning labels if they become obscured or removed. 4. This Woodworking Jointer is designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the proper and safe operation of a woodworking jointer, do not use until proper training and knowledge have been obtained. 5. Do not use this Jointer for other than its intended use. If used for other purposes, JET disclaims any real or implied warranty and holds itself harmless from any injury that may result from that use. 6. Always wear approved safety glasses/face shields while using this woodworking jointer. Everyday eyeglasses only have impact resistant lenses; they are not safety glasses. 7. Before operating this woodworking jointer, remove tie, rings, watches and other jewelry, and roll sleeves up past the elbows. Remove all loose clothing and confine long hair. Non-slip footwear or anti-skid floor strips are recommended. Do not wear gloves. 8. Wear ear protectors (plugs or muffs) during extended periods of operation.
    [Show full text]
  • Treasured Chest a Mahogany Storage Case for Your Most Prized Possessions
    Treasured Chest A mahogany storage case for your most prized possessions. If you're the type who empties his pockets onto the dresser top, or keeps everything from an old high-school ring to snapshots of last year's office party in the sock drawer, it's time to get organized--and we've got just the project to help. Our mahogany chest of drawers is based on the type traditionally used by craftsmen to store precision tools. However, you don't need to own a micrometer to make good use of it. With its six felt-lined drawers and locking top compartment, it's the ideal place to store or display jewelry, collectibles, memorabilia and all those little things that never seem to find a home of their own. While the construction of the chest isn't difficult, its small size means extra care must be taken in all stages-- especially the fitting of the drawers. We planed most of the stock to 5/8 in. thick, and used 1/4- and 1/2-in. wood for the panels and drawer sides. Lumber in these sizes isn't usually stocked by suppliers--if you don't have a planer, ask your dealer or a local shop to reduce thicker material. When selecting stock, look for consistent color and grain pattern. If you have some wood that varies in appearance, use it in the case bottom or drawer sides where the difference will not be too visible. Rip and crosscut all parts to finished dimension. Be sure to mill some extra stock to use for testing saw and router setups.
    [Show full text]
  • SATURDAY MAY 6, 2017 LIST Humboldt Antique Tool Auction May
    SATURDAY MAY 6, 2017 LIST Humboldt Antique Tool Auction May 5 and May 6, 2017 Humboldt Fairgrounds 311 6th Ave. North Humboldt, IA 50548 Preview Friday 2:00 to 3:35 PM Friday Auction begins 3:35 PM Preview Saturday 8:00 to 9:35 AM Saturday Auction begins 9:35 AM The lots marked TBA will be filled with items taken the three pallets of in-the-rough gear we cleaned out of a Wisconsin barn and then put in storage in Humboldt. Included in this lot will be buggy jacks, barn pulleys, a cast iron body of the cream separator and a wide variety of other antique tools and farm tools. We will lay this gear out in beer flats and individual lots and will number them in order Friday 180-184; 234-250; and 277-290 & on Saturday: 300, 441-449; and 597-625. 1 ______ Winchester 3026C wide body jack plane, tote broken in center and needing glue, will clean to very good overall. 2 ______ Stanley #92 shoulder plane with light rust on MADE IN USA blade, very good overall. 3 ______ Belknap BLUEGRASS iron jack plane, fine except for patch of rust on bottom where it sat on a damp shelf, will clean to fine overall. 4 ______ Scarce Stanley #94 shoulder plane, the biggest one they made, this one is complete and in very good overall condition, just needs a good cleaning. 5 ______ Keen Kutter KK190 iron rabbet plane with very good original blade, nice japanning, complete with depth stop, very good overall.
    [Show full text]
  • Insulated Glazing Panels
    NEW INSULATED GLAZING PANELS 3255 Penn Street, Hatfield, PA 19440-1731 800.523.2347 I LaminatorsInc.com Effective March 2019 Tech Support: 800.523.2347 LaminatorsInc.com NEW INSULATED GLAZING PANELS In addition to our standard flat Thermolite™ panel, Laminators now offers fabricated options to provide additional R-Value, new aesthetics, and the ability to create hairline joints between panels. Thermolite Glazing Panels are designed to easily fit into any standard or custom glazing system. With building and energy efficiency codes becoming even more stringent, these panels can be a smart solution for your next project. When you need a high-tech look with energy-saving, insulating properties for glazing inserts, Thermolite panels are the answer. Thermolite panels are constructed with an insulating foam core sandwiched between finished aluminum sheets and two corrugated stabilizers. Available in smooth or stucco-embossed finishes in a variety of colors, Thermolite panels create a highly decorative and durable surface with excellent insulating properties. Features Applications • Custom Colors • Curtain Walls • Smooth or Stucco-Embossed Finish* • Window Systems • Project-Specific Customization • Window Replacement • 5-Year Panel Construction Warranty • Commercial Door Systems • Opaque Glazing *See chart for details. • Storefronts • In-Fill Panels • Spandrels • Butt Glazing THERMOLITE™ U-MAX A 7-ply, rabbet edge panel designed to provide increased insulation on the interior face of the panel. Thermolite U-MAX is a multi-layered, insulated glazing panel that consists of two foam plastic cores bonded to three thermoplastic stabilizers with finished sheets of aluminum on each face. Intended for use in standard glazing pockets of window, glazing, and curtain wall systems, panels include stepped edges on the interior side.
    [Show full text]
  • CANADA January 2, 2018
    Price List / Liste Des Prix CANADA January 2, 2018 MOULDING WOOD MOULDING PRICING MATRICES 3-6 WOOD MOULDING COLLECTION 7 RPS MOULDING PRICING MATRICES 18 RPS POLYSTYRENE MOULDING 22 GALLERY FRAMES COLLECTION 28 FRAMING SUPPLIES FOAM BOARD 33 TOUCH-UP & FILLERS 48 GLASS, ACRYLIC, MIRROR 34 FITTING & BACKING SUPPLIES 50 TAPES, ADHESIVES, & MOUNTING SUPPLIES 37 MOUNTING & HANGING SUPPLIES 51 CONSERVATION TAPES, ADHESIVES 38 SPECIALTY TOOLS & CLEANING ITEMS 51 MOUNTING TISSUES & ADHESIVE RELEASE BOARDS 38 KRAFT PAPER & DISPENSERS 53 GLUES & ADHESIVES 39 GALLERY HANGING & DISPLAY PRODUCTS 53 WIRE PRODUCTS 40 PACKING MATERIALS & SUPPLIES 53 BLADES - MAT CUTTING & GENERAL USE 41 EDUCATIONAL MEDIA 54 V-NAILS 42 MACHINERY 55 JOINING, POINT DRIVERS, STAPLERS & POINTS 43 MATBOARD 57 PICTURE HANGING HARDWARE & FASTENERS 44 TERMS & CONDITIONS 79, 80 Voice: 1-877-452-3799 • Fax: 1-877-452-3783 2018 www.omegamoulding.ca Retail Joined Frame Matrices are available online www.omegamoulding.ca/documents.aspx • Download & print the desired pricing matrix that fi ts your selling strategy Order Online at Omegamoulding.ca ! Placing an order has never been easier! Use Omega’s Quick Order system to fi nd everything you need from mouldings and Gallery Frames to framing supplies at your convenience 24 hours a day. Update Your Walls with Omega’s Innovative Web Tool! In our eff ort to lead the industry in developing helpful productivity tools which make your business run more smoothly, we have developed a tool that will allow you to quickly and easily fi nd discontinued Omega Moulding samples in your wall displays. This tool called “Your Discontinued Corners” can be found under the “Products” tab in the top navigation bar on the omegamoulding.ca homepage.
    [Show full text]
  • FINAL MARK-DOWNS Subcontract Delivery, at Aer- Were A
    City Employes Can Participate DECEMBER 10, 1967 RESS-HERAID A-3 In Politics, Attorney Reports Retail Receipts A section of the Torrance Code which prohibit city em­ Remelmeyer said sections city charter which prohibits ployes from participating in of local and state codes which Reach New Highs city employes from engaging political campaigns to be un- prohibit city employes from in local political campaigns constitutional. soliciting or receiving politi­ While most Southern California cities experienced a apparently is unconstitutional, He said any city employe, cal contributions from other first six months of city employes are valid. drop-off in retail sales during the City Attorney Stanley Kernel under the court rulings, could Ifl67, Torrance forged ahead. According to a report pre­ meyer said Tuesday night. i engage in active political ac A section which prohibits Remelmeyer, in an opinionjtivity "so long as his activities city employes from engaging pared by the Redondo Beach Chamber of Commerce, landed to councilmen. said! are conducted on his own! in political activities while in Torrance increased its sales by a whopping $13.8 mil­ recent court cases have held time, away from city facil-i uniform also is valid. lion. sections of the city charter. ities, in civilian clothes, and| Remelmever recommended Among major cities running behind are Los Angeles the Torrance Municipal Code,!absent of any representation that the sections of the city ($38'4 million). Long Beach ($3V4 million), and Santa and tire State Governmentlof city government." city employes be submitted to Eight other cities in this area also experienced an Problems of Adolescent the voters with a recommen­ upward trend in receipts netted during the first six dation for repeal.
    [Show full text]
  • Performance Standards for Table Saws
    BALLOT VOTE SHEET DATE: JUN 2 8 2006 TO: The Commission Todd A. Stevenson, Secretary THROUGH: Patricia M. Semple, Executive Directorv5 /-- FROM: PC'- General Counsel for Enforcement and Information P5k SUBJECT: Petition CP 03-2, Performance Standards for Table Saws JuL 6 2006 Ballot Vote Due: - Attached is a briefing memo from the staff concerning a petition from Stephen Gass, David Fanning, and James Fulmer requesting mandatory performance standards to reduce or prevent table saw blade contact injuries. The staff recommends that the Commission grant the petition to the extent it requests the Commission to proceed with a rulemaking process that could result in a mandatory safety standard for table saws to reduce the risk of blade contact injury, and direct the staff to prepare an advance notice of proposed rulemaking (ANPR). Please indicate your vote on the following options. I. Grant Petition CP 03-2 and direct staff to draft an ANPR. (Signature) (Date) -. 96 CPSC Hotl~ne:1-800-638-CPSC(2772) CPSC's Web Site, httu~llwwwcusc qov Page 1 of 2 NwI ' ~TIONS REMOVE^: \ 11. Deny Petition CP 03-2 and direct staff to prepare a letter of denial to the petitioners. (Signature) (Date) 111. Defer decision on Petition CP 03-2. (Signature) (Date) IV. Take other action (please specify): (Signature) (Date) Attachment: Briefing memo on Petition CP 03-2. Page 2 of 2 BRIEFING PACKAGE PETITION FOR PERFORMANCE STANDARDS FOR TABLE SAWS June 2006 For Further Information Contact: Caroleene Paul Project Manager Directorate for Engineering Sciences 301-504-7540 Executive Summary This briefing package provides the Commission with available information about blade contact injuries associated with table saw use and describes options for the Commission to consider in determining whether a rule may be reasonably necessary to eliminate or reduce the risk of table saw blade contact injury.
    [Show full text]
  • Tool Shed Number 140 February 2006
    NUMBER 140 February 2006 A Journal of Tool Collecting published by CRAFTS of New Jersey The Saga of a Hammer By Carl Bopp ( Time line, about 1986) – Years ago after antique some questions about it. I was told, no, he was not shops started renting showcases so dealers didn’t in but they could open the case for me but they had have to spend any or very little floor time, I made no knowledge of the hammer in question. my first purchase from such a case. It was at a large After the hammer was retrieved from the case, I antique shop in Smith- could see that it had ville, (Atlantic County) numbers marked on its N. J. that has since been head and the handle torn down. The show- was some unknown case area was in a long reddish material with a foyer. In one large black inlay trimmed locked case, I spied an with thin brass. Figure unusual hammer. Figure 2 & 3. After getting it 1. It was of a shape that home, I could see the I was not familiar with. numbers were intended Obviously it was not to measure something. intended for heavy duty (Time line, Nov. work. The head was 1989) – Turning to my slim looking and the han- copy of The Hammer dle was at one point very the King of Tools, by slender. The tag with it Ron Baird and Dan said it was a “railroad Comerford, that had hammer”, which I knew just been published, I couldn’t be right because found the same ham- railroad tools are very mer on page 60.
    [Show full text]