DOCSLIB.ORG

N -AIR™PRODUCTS Ace Glass Introduces Our New, Updated Product Line for Air Sensitive and NO-AIR™ Chemistry

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
N -AIR™PRODUCTS Ace Glass Introduces Our New, Updated Product Line for Air Sensitive and NO-AIR™ Chemistry Adapters • Flasks • Funnels • Manifolds • Stopcocks • Traps • Tubes • Valves N -AIR™PRODUCTS Ace Glass introduces our new, updated product line for air sensitive and NO-AIR™ chemistry. This brochure details all of Ace Glass’ components, for setting up full systems. 2 General Information Specifications In case of Shortage: 1. Notify ACE immediately. The products in this catalog represent what we believe to be 2. A replacement will be issued upon confirming inventory the most advanced design and construction. However, design discrepancy. improvements are constantly being made, and we reserve the right to modify specifications where we feel that a change is In case of Loss: warranted. 1. First, please verify with all your receiving departments Apparatus fabricated in accordance with ASTM, API, AOAC and that delivery was not made. other technical organization specifications such as USP, NIST, 2. Notify ACE immediately. and NIOSH, are subject to modification by these organizations. 3. ACE will contact the carrier for tracking information as All precision-grade ware is warranted to be within the tolerance applicable. prescribed in ASTM Specifications. All laboratory-grade ware is 4. A replacement will be issued upon verification that the twice precision-grade tolerances. shipment was not delivered and upon confirmation that the carrier cannot locate shipment. Special Apparatus PLEASE NOTE: Orders or inquiries for special apparatus should be All breakages and shortages must be accom panied by prints or drawings, if possible. To prevent delay, and to enable us to more intelligently quote on reported within two weeks of receipt. your specials, all necessary dimensions and tolerances should be noted. For technical information, design assistance and help please visit www.aceglass.com. Returns and Repairs The following information should also be furnished where Incoming material (returns or repairs) must be pre-approved applicable: joint sizes, Ace-Thred sizes, capacity, whether “to by our Product Return Specialist. Please follow these steps to contain” or “to deliver,” porosity of filter, and any abnormal ensure our Receiving Department does not refuse your shipment. operating conditions, such as extremely high pressure or Contact ACE for an RA# (Return Authorization Number). temperature, to which the apparatus may be subjected. 1-800-223-4524 (Vineland, NJ, USA) We reserve the right to overrun or under run by 10% on orders 1 E-mail: [email protected] for special items and to ship and invoice for amounts within this variation. 2. Once an RA# is given, properly pack the item(s) in an inner and outer box/carton and write the RA# on the NOTE: Special items are not returnable. outside of the box. All used items are to be thoroughly Our research and drafting departments are always available to cleaned and defined in the assignment of an RA#. assist you in designing special apparatus. Your special will be 3. A 20% restocking fee will be assessed for returns assigned a permanent drawing number for future reference, (items ordered incorrectly or items no longer needed, duplication or change. You will be sent a drawing of your special etc.) unless arranged otherwise. ACE cannot accept for your approval/sign-off before manufacturing begins. responsibility for damage or destruction of glassware that occurs in your shipment to us. We strongly advise you to Types of Glass purchase additional insurance with your carrier. 4. For Returns that are the result of your receiving the All ACE-manufactured glassware items listed in this catalog item(s) broken, ACE cannot accept responsibility for are, unless otherwise noted, fabricated from 33 expansion further damage or destruction of glassware that occurs ® borosilicate glass, such as Pyrex Brand Glass, a product of in the return shipment due to improper packing. Corning Incorporated; KG-33 Glass, a product of Kimble Glass 5. Repairs will be evaluated by our technicians. You will Company; Duran Glass, Simax, a product of Kavalier Glassworks. be advised if any pieces are beyond repair or cannot be salvaged economically. ACE cannot accept responsibility Breakage or Loss for further damage or destruction of any glassware that is damaged during return shipment. In case of Breakage: 1. Notify ACE immediately. PLEASE NOTE: 2. Please retain all inner and outer cartons and ACE cannot accept responsibility packing material. for material sent in without proper 3. ACE will advise you whether the carrier will report to your location for inspection or if item(s) authorization. are to be returned for inspection. For Engineering Support, visit www.aceglass.com General Information 3 Order by Code ACE Glassware Discounts Each item in this catalog has a two- or three-digit code in All ACE-manufactured glassware, identified with a spade ♠( ), addition to the four- or five-digit number. This code appears listed in this catalog is subject to the following dollar value above or immediately preceding the price of the item, and no discounts. Items marked by a star (★) or that have no designation other ordering information is needed since each individual size, whatsoever are not subject to this discount. capacity, etc. has its own code. Example: 5117-21. 10% on purchases of $500.00 and over The majority of items listed in this catalog are normally available 12% on purchases of $1,000.00 and over from stock at our plant in Vineland, NJ. 15% on purchases of $1,500.00 and over In the event your entire order cannot be filled immediately, Terms: Net 30 days (Domestic only) a partial shipment will be sent, with the back-ordered items following shortly. If you would like the entire order to be sent Contact ACE for a current price list/ in one shipment, please indicate this on your purchase order. pricing CD, or visit our website, Unless otherwise specified on the purchase order, we will ship www.aceglass.com. material by what we consider the “best way.” Ways to Order Ace Glass products are also available from our many lab distribution partners, particularly VWR International, LLC and ACE Sigma-Aldrich. ACE Laboratory Glassware PHONE 856-692-3333 isis intendedintended forfor 800-223-4524 laboratorylaboratory useuse only.only. FAX 856-692-8919 800-543-6752 ProperProper CREDIT CARD VISA laboratory procedures MasterCard laboratory procedures American Express and safety practices MAIL P.O. Box 688 should always Vineland, NJ 08362 be followed. WEB SITE www.aceglass.com E-MAIL [email protected] INTERNATIONAL [email protected] Shipments are F.O.B. our factory in Vineland, NJ, USA. INTERNATIONAL SALES Ways to Order Methods of Payment Mail: Ace Glass Incorporated ◾ Wire Transfer International Sales Dept. 1430 N. West Blvd — P.O. Box 688 ◾ Irrevocable, payable on-sight, Vineland, NJ 08360-0688 USA and confirmed letter of credit Phone: 856-692-3333 ◾ Payment in advance by check or money order, in US Funds only Fax: 856-692-8919 ◾ Credit Card: Amex, Visa, MasterCard, etc. E-mail: [email protected] Ordering & Product Information: 1-800-223-4524 www.aceglass.com 4 Adapters Hose Connection Size Guide Dimensions in Millimeters 3.0 3.5 3.0 4.0 5.0 7.7 7.3 6.5 7.1 6.0 8.9 8.4 12.5 13.8 10.5 10.4 10.0 12.5 11.5 12.9 16.2 Use with Use with Use with Use with Use with Use with Use with 7.9mm (5/16") 7.9mm (5/16") 7.9mm (5/16") 9.5mm (3/8") 9.5mm (3/8") 11.1mm (7/16") 15.9mm (5/8") I.D. Tubing or 9.5mm (3/8") or 9.5mm (3/8") I.D. Tubing or 11.1mm (7/16") or 12.7mm (1/2") I.D. Tubing I.D. Tubing I.D. Tubing I.D. Tubing I.D. Tubing 3844 ADAPTER Easy Action Stopcock, ST Joints, NO-AIR™ With 0-3 or 0-5 Easy-Action threaded plug and inner and reinforced outer joints at top and bottom. Plug Bottom Top Plug Bottom Top Bore, Inner Outer Order Bore, Inner Outer Order mm Joint Joint Code mm Joint Joint Code 0-3 14/20 14/20 3844-05 0-10 24/40 24/40 3844-47 0-3 24/40 24/40 3844-07 0-10 29/42 29/42 3844-49 0-3 29/42 29/42 3844-09 0-5 14/20 14/20 3844-31 0-5 24/40 24/40 3844-34 3844 0-5 29/42 29/42 3844-36 3845 ADAPTER Easy Action Stopcock, No. 15 O-Ring Joints, NO-AIR™ 3845 Easy-Action stopcock with No. 15 O-Ring joint at top and bottom. Supplied with two size –116, 7855-726 FETFE O-Rings. Plug Bottom Top Bore, O-Ring O-Ring Order mm Joint Joint Code 0-5 No. 15 No. 15 3845-05 0-10 No. 15 No. 15 3845-10 3846 ADAPTER Glass Stopcock, No. 15 O-Ring, NO-AIR™ 3846-05 With 4mm glass plug stopcock and No. 15 O-Ring top joint and either or JS joints at 3846-07 bottom. Uses size –116 FETFE O-Rings, 7855-726. Plug Top Bore, Bottom O-Ring Order mm Joint Joint Code 4 JS 35/25 Ball No. 15 3846-05 4 JS 35/25 Socket No. 15 3846-07 4 24/40 No. 15 3846-09 3846-09, 4 29/42 No. 15 3846-11 -11, -13 4 14/20 No. 15 3846-13 For Engineering Support, visit www.aceglass.com Adapters 5 3847 ADAPTER PTFE Stopcock, No. 15 O-Ring With 4mm PTFE plug stopcock and No. 15 O-Ring top joint and either or JS joints at bottom. Uses size –116 FETFE O-Rings, 7855-726. Plug Top Bore, Bottom O-Ring Order mm Joint Joint Code 4 JS 35/25 Socket No.
Load more

Recommended publications
  • Chem 1140; Techniques for Handling Air-Sensitive Compounds
    P. Wipf 1 Chem 1140 Chem 1140; Techniques for Handling Air-Sensitive Compounds • Introduction • The Glove Box • Schlenk Techniques • Drying and Degassing Solvents What are Air-Sensitive Compounds? Materials which oxidize, decompose or even explode under the influence of oxygen or moisture. • Pyrophoric Compounds Metal alkyls and aryls e.g. RMgX, RLi, RNa,R3Al, R2Zn Metal carbonyls e.g. Ni(CO)4, Fe(CO)5, Co2(CO)8 Alkali metals e.g. Na, K, Cs Metal powders e.g. Al, Co, Fe, Mg, Pd, Pt, Zn Metal hydrides e.g. NaH, KH, LiAlH4 Hydrides e.g. B2H6, PH3, AsH3 Boranes, phosphines, arsenes, etc. e.g. Et3B, R3P, R3As • Chemicals which react violently with water Metal hydrides, metal amides (NaNH2), metal alkyls and aryls, metals, metal powders, hydrides, many main group halides (BCl3, BF3, AlCl3, PCl3, SiCl4), inorganic acid halides (POCl3, SOCl2), low molecular weight organic acid halides and anhydrides. Glove boxes and Schlenk techniques do NOT protect from explosive or shock sensitive materials or mixtures!!! Also, they only provide limited protection from toxic compounds. P. Wipf 2 Chem 1140 The Glove Box • The best way to keep things away from atmospheric oxygen and water is to work in a fully enclosed “bench top,” containing an “inert atmosphere,” which one could reach into with gloves. Such a device is called a “glove box” or a “dry box”. There are also cheap “glove bags”, bags you can fill with inert gas and reach into with attached gloves. The Glove Box A glove box has four important components: 1. The actual “box” is a large aluminum chamber with a plastic front window and two impressive looking gloves.
    [Show full text]
  • Standard Operating Procedures Standard Operating Procedures Tolman Laboratory
    Tolman Group Standard Operating Procedures Standard Operating Procedures Tolman Laboratory v.7 updated May 2016 The intent of this manual is to inform you, the chemist, of the potential hazards that exist in the laboratory. This is by no means a manual to memorize or a manual of instruction. These procedures are not intended to be exhaustive or to serve as a single method of training. The procedures outlined here are meant as a refresher for those who have already received training by senior lab members. If in doubt of any procedure, please ask someone before carrying out said procedure. Asking for help when in doubt is the responsibility of every lab member. The first time you use all equipment and perform new experimental procedures, you should have someone work with you to teach you and to inform you of potential hazards, and to help prevent accidents. The purpose of this manual is to supplement personal one-on-one training with safety information that will protect you personally, as well as other lab members. It is important to make sure that you minimize your exposure to chemicals and decrease the chances of any accidents. By reviewing (and later referring to) this manual, you can be aware of the potential hazards in the lab and learn careful techniques. It is your responsibility to learn about safety and proper handling of chemicals from the resources available, including your laboratory members, other persons in the department, and the Chemical Hygiene Plan, which can be accessed via the web, from the Safety link on the Chemistry Webpage www.chem.umn.edu, or http://www.chem.umn.edu/services/safety/.
    [Show full text]
  • Bartlett Group
    Bartlett Group University of Michigan Department of Chemistry 930 N. University Avenue Ann Arbor, MI 48109-1055 Standard Operating Procedures Original Version (1.0) Approved: February 3, 2012 Version 1.5 Approved: February 13, 2017 Table of Contents USE OF THE BASE and ACID BATHS, GENERAL HANDLING OF ACIDS AND BASES ....... 2 WORKING WITH STRONG OXIDANTS ...................................................................................... 6 WORKING WITH AQUA REGIA ................................................................................................ 11 WORKING WITH PIRANHA CLEANING SOLUTION ............................................................... 13 USING THE SCHLENK LINE ..................................................................................................... 16 USING THE GLOVEBOX ........................................................................................................... 22 USING THE SOLVENT PURIFICATION SYSTEM .................................................................... 26 USING HYDROTHERMAL REACTION VESSELS .................................................................... 28 USING THE CENTRIFUGE AND VACUUM OVEN ................................................................... 30 USING COMPRESSED GAS CYLINDERS ............................................................................... 33 USING THE TUBE FURNACE ................................................................................................... 38 GLASS CUTTING AND USING FLUORINATED TIN OXIDE ...................................................
    [Show full text]
  • Schlenk Line SOP SOP ID #:ESB002 Revision #:2 Date:December 3, 2014 Page 1 of 5 Schlenk Line Standard Operating Procedure
    Title: Schlenk Line SOP SOP ID #:ESB002 Revision #:2 Date:December 3, 2014 Page 1 of 5 Schlenk Line Standard Operating Procedure Lab: Engineering Sciences Building 155 Department: Materials Science and Engineering PI: Paul V. Braun Written By: Jin Gu Kang Section 1: Overview Type of SOP: ☒Process ☐Hazardous Material ☐Hazardous Class of Materials ☒Equipment Synopsis: The dual vacuum manifold line, also known as a Schlenk line, is a standing piece of glassware used to surround the contents of a chemical flask in an inert atmosphere of Ar or N2 gas. This instrument is critical for many important reactions including polymer chemistry, quantum dot synthesis, and any other variant of synthetic chemistry that requires the minimization of contact with air or other airborne contaminants. The Braun group has four different Schlenk lines—three located in the Beckman Institute, and one in the Engineering Sciences Building. In order to operate a Schlenk line for experimental chemistry, a user must be trained in methods to operate the valves and to introduce the proper gases as needed to ensure smooth operation and a desirable experiment. Proper use of a Schlenk line is quite complicated, hence the following procedures must be strictly observed after an initial series of trainings to avoid potential hazards and accidents that could compromise the expensive Schlenk glassware. Section 2: Risk Assessment Summary (Hazards and control measures) Title: Schlenk Line SOP SOP ID #:ESB002 Revision #:2 Date:December 3, 2014 Page 2 of 5 Materials and Equipment Hazards: The Schlenk Line: The Braun group Schlenk lines were designed and blown by the chemistry department’s glass shop in Noyes Laboratory.
    [Show full text]
  • And Schlenk Line (SL) Safety Tilak Chandra and Jeffrey P
    Vacuum System (VS) and Schlenk Line (SL) Safety Tilak Chandra and Jeffrey P. Zebrowski Environment Health & Safety, UW-Madison, WI 53715 ` INTRODUCTION Fig. 6: Vacuum set-up for biological material aspiration Vacuum System (VS) & Schlenk Line (SL; Fig. 1) are effective and SL in laboratories should be installed in a safe location, preferably inside Fig. 4: Vacuum pump exhaust system common devices in research laboratories for various chemical a chemical fume hood, to avoid impacts from glass implosion and manipulations. Generally in a laboratory set-up two types of chemical exposures (Fig. 3). To exhaust system To exhaust system HEPA Vacuum filter vacuum systems are used—water aspirators and mechanical Vacuum pumps. Water aspirators are common in chemistry labs for filtration Fig 3. Schlenk line set-up Oil blockage purposes, however water aspirators consume plenty of water (11 lit/min). Mechanical pumps are more useful for providing high Bleach B A vacuum for SL and many other laboratory instruments. Overflow collection flask X PUMP PUMP Fig. 1: Vacuum and Schlenk Line system Schlenk Line Cold Trap Safety (Liquid Oxygen Condensation) Vacuum Pump Maintenance (Oil Change) • Extreme care should be taken if liquid nitrogen is used for the trap to • Regularly monitor the condition of the pump oil and filters. Pumps used for avoid the condensation of oxygen from air. conducting corrosive chemical manipulations are more prone to damage and o o require frequent oil change. VACUUM • Oxygen has a higher boiling point (-297 F) than nitrogen (-320 F) MANIFOLD PUMP and will condense out of the atmosphere and collect in a liquid- • Use sight-glass to check the oil-level which should be between the Max and TRAPS nitrogen cooled container open to the air (EXPLOSION HAZARD).
    [Show full text]
  • Schlenk Line Design and Safety by Patrick Frank Stanford Synchrotron Radiation Lightsource, SLAC, Stanford University 04 April 2011
    Schlenk Line Design and Safety By Patrick Frank Stanford Synchrotron Radiation Lightsource, SLAC, Stanford University 04 April 2011 This report will begin with a description of a functioning Schlenk line, describing the separate parts and how they function together. Following after is a discussion of the various operational and physical (not chemical) elements of safety when using the Schlenk line. General PPE recommendations: • Safety glasses or goggles are required all the while a Schlenk line is in use. Face shields are optional. • Safety glasses are required when obtaining or using liquid nitrogen. • Thermal gloves are required as needed when dispensing or using liquid nitrogen or cold Dewars. • Lab coat and face shield are required if using especially reactive chemicals (pyrophorics or explosive mixtures). • Plastic lab coats are to be avoided unless they are explicitly rated as flame-proof. • The hood sash must be pulled down when the Schlenk line is unattended. • An explosion shield required when working with especially reactive chemicals (pyrophorics or explosive mixtures). Explosion hazard is evaluated on an experimental case-by-case basis. • An explosion shield is optional during vacuum distillation. I. Schlenk Line Description I.1 Introduction. Schlenk line is a tubular glass apparatus used to perform air-free bench- top chemical manipulations. Air-free work is required when reagents or products are sensitive to oxidation. A Schlenk line centrally consists of a duplex of glass tubes connected side-by-side, which together is called a “manifold.” The manifold is connected to a vacuum pump and a source of inert gas (N2 or Ar). A Schlenk line is most safely operated within a working hood.
    [Show full text]
  • Schlenk Lines Transfer of Solvents
    Journal of Visualized Experiments www.jove.com Science Education Collection Schlenk Lines Transfer of Solvents URL: https://www.jove.com/science-education/5679 Overview Source: Hsin-Chun Chiu and Tyler J. Morin, laboratory of Dr. Ian Tonks—University of Minnesota Twin Cities Schlenk lines and high vacuum lines are both used to exclude moisture and oxygen from reactions by running reactions under a slight overpressure of inert gas (usually N2 or Ar) or under vacuum. Vacuum transfer has been developed as a method separate solvents (other volatile reagents) from drying agents (or other nonvolatile agents) and dispense them to reaction or storage vessels while maintaining an air- free environment. Similar to thermal distillations, vacuum transfer separates solvents by vaporizing and condensing them in another receiving vessel; however, vacuum transfers utilize the low pressure in the manifolds of Schlenk and high vacuum lines to lower boiling points to room temperature or below, allowing for cryogenic distillations. This technique can provide a safer alternative to thermal distillation for the collection of air- and moisture-free solvents. After the vacuum transfer, the water content of the collected solvent can be tested quantitatively by Karl Fischer 1 titration, qualitatively by titration with a Na/Ph2CO solution, or by H NMR spectroscopy. Principles Purified solvents that are both moisture- and oxygen-free are needed in diverse fields of chemistry, from small molecule synthesis to advanced materials applications.1-3 For example, butyllithium, which is commonly used in organic synthesis and as an anionic polymerization initiator, is water-reactive and trace water in solvents can greatly affect the actual reagent concentration.
    [Show full text]
  • Kerim Samedov[B], Roman G. Belli[A],C. Jonath
    Electronic Supplementary Material (ESI) for ChemComm. This journal is © The Royal Society of Chemistry 2020 Supporting Information for A Thermolytic Route to a Polysilyne Peter T. K. Lee[a], Kerim Samedov[b], Roman G. Belli[a], C. Jonathan Clarke[a], Derek P. Gates*[b], and Lisa Rosenberg*[a] [a] Department of Chemistry, University of Victoria, P.O. Box 1700, STN CSC, Victoria, BC, Canada, V8W 2Y2; e-mail: [email protected] [b] Department of Chemistry, University of British Columbia, 2036 Main Mall, Vancouver, BC, Canada, V6T 1Z1; e-mail: [email protected] General experimental details S2 Polymer syntheses S3 Polymer characterization S6 Photolysis experiments S11 S2 General experimental details Synthesis and reagents. Unless otherwise noted, all reactions and manipulations were performed under nitrogen in a glovebox or using conventional Schlenk techniques. A “bomb” flask is a thick-walled flask with a 4 mm teflon needle valve and side-arm with a ground glass joint for connection to a Schlenk line. Benzene was distilled from sodium/benzophenone under nitrogen; toluene and hexanes were degassed by sparging with nitrogen and dried over activated alumina in a solvent purification system. THF was distilled from sodium/benzophenone and degassed by three freeze-pump-thaw cycles before use. Isopropanol was refluxed with Mg turnings for 3h, distilled, deoxygenated by sparging with nitrogen for 12h, and stored over Linde type 5 Å molecular sieves. Deuterated C6D6 was freeze-pump-thaw degassed and vacuum transferred from sodium/benzophenone. Degassed HPLC grade tetrahydrofuran (THF) was used for Gel Permeation Chromatography (GPC) analysis. Spectroscopic grade dichloromethane was dried and stored over activated molecular sieves and degassed by three freeze-pump-thaw cycles before use.
    [Show full text]
  • Vacuum System and Schlenk Line Safety
    Vacuum System (VS) and Schlenk Line (SL) Safety Tilak Chandra and Jeffrey P. Zebrowski Environment Health & Safety, UW-Madison, WI 53715 ` INTRODUCTION Fig. 6: Vacuum set-up for biological material aspiration Vacuum System (VS) & Schlenk Line (SL; Fig. 1) are effective and SL in laboratories should be installed in a safe location, preferably inside Fig. 4: Vacuum pump exhaust system common devices in research laboratories for various chemical a chemical fume hood, to avoid impacts from glass implosion and manipulations. Generally in a laboratory set-up two types of chemical exposures (Fig. 3). To exhaust system To exhaust system HEPA Vacuum filter vacuum systems are used—water aspirators and mechanical Vacuum pumps. Water aspirators are common in chemistry labs for filtration Fig 3. Schlenk line set-up Oil blockage purposes, however water aspirators consume plenty of water (11 lit/min). Mechanical pumps are more useful for providing high Bleach B A vacuum for SL and many other laboratory instruments. Overflow collection flask X PUMP PUMP Fig. 1: Vacuum and Schlenk Line system Schlenk Line Cold Trap Safety (Liquid Oxygen Condensation) Vacuum Pump Maintenance (Oil Change) • Extreme care should be taken if liquid nitrogen is used for the trap to • Regularly monitor the condition of the pump oil and filters. Pumps used for avoid the condensation of oxygen from air. conducting corrosive chemical manipulations are more prone to damage and o o require frequent oil change. VACUUM • Oxygen has a higher boiling point (-297 F) than nitrogen (-320 F) MANIFOLD PUMP and will condense out of the atmosphere and collect in a liquid- • Use sight-glass to check the oil-level which should be between the Max and TRAPS nitrogen cooled container open to the air (EXPLOSION HAZARD).
    [Show full text]
  • Using Earth Abundant Materials for the Catalytic Evolution of Hydrogen from Electron-Coupled-Proton-Buffers
    Electronic Supplementary Material (ESI) for Sustainable Energy & Fuels. This journal is © The Royal Society of Chemistry 2017 Supplementary Information for: Using Earth Abundant Materials for the Catalytic Evolution of Hydrogen from Electron-Coupled-Proton-Buffers Lewis MacDonalda , Jessica C. McGlynna, Nicola Irvinea, Ihfaf Alshibanea, Leanne G. Bloora, Benjamin Rauscha, Justin S. J. Hargreavesa, Leroy Cronin*a a WestCHEM, School of Chemistry, University of Glasgow, University Avenue, Glasgow, G12 8QQ, UK * Corresponding author, [email protected] Contents SI-1 General Experimental Remarks 3 SI-2 Electrochemical methods 3 SI-3 Electrochemical testing and reduction of redox mediators 5 SI-4 Hydrogen evolution from ECPB’s in the presence of purchased and 7 synthesised catalysts SI-5 Theory of variation of hydrogen evolution 9 SI-6 Catalyst Synthesis 11 SI-7 Characterisation of catalysts 13 SI-8 SMA and PMA CV’s overlaid onto HER onset graphs 28 SI-9 Reusability of earth abundant catalysts with STA 29 SI-10 Tables 30 SI-11 References 33 SI-1: General Experimental Remarks: The solvents used throughout the experimental procedures were purchased from Sigma Aldrich. All chemicals purchased for the synthesis of the earth abundant catalysts were purchased from Sigma Aldrich. Nafion N-117 (0.18mm thick) membrane, used in the H-cells, was purchased from Alfa Aesar. Carbon felt, used as a high surface area working electrode, was purchased from either Alfa Aesar (43199, 3.18mm thick, 99.0%) or FuelCellStore (AvCarb G100 Soft Graphite Battery Felt, 3.2mm thick, 99%). Nitrogen (OFN) and argon (Pureshield) gas cylinders were purchased from BOC.
    [Show full text]
  • Hu Lab Manual
    Laboratory of Inorganic Synthesis and Catalysis Ecole Polytechnique Fédérale de Lausanne Lab Manual Guidelines, Procedures, & Requirements Updated: October 2010 Written by Xile HU Disclaimer: This is not an original publication. The information used in this manual is collected from various online sources with the aid of Internet searching tools. To follow good practices of others, many paragraphs were taken directly from existing research lab manuals without modification. The author does not claim any copyright ownership of this manual, which solely serves to guide the activity of his research group. Despite all efforts, some information/guideline described here might not be 100% accurate. The author bears no responsibility for any consequence that the use of this manual in other research labs arises. 1 Contents Introduction ................................................................................................................................... 4 Philosophy ...................................................................................................................................... 4 Administration .............................................................................................................................. 4 Additional points for Ph.D. students ....................................................................................... 5 Description of Lab Jobs ................................................................................................................ 5 Lab Protocols I: Reading, Writing,
    [Show full text]
  • 1 Standard Operating Procedure Inert Gas/Vacuum Schlenk Line John
    Standard Operating Procedure Inert Gas/Vacuum Schlenk Line John Hodul, February 2019 Description of Process The inert vacuum lines located in fume hoods 1,2, and 3 in FRNY 2182 require special training in order to use them. These pieces of equipment are used for removing oxygen and water from reaction vessels with nitrogen (N2) or Argon (Ar) via purge/refilling or freeze-pump-thaw techniques. Required Training Purdue School of Chemical Engineering Safety Orientation P.O.W.E.R. Lab safety orientation (including fume hood induction) Engineering and Ventilation Controls The schlenk lines are located inside of fume hoods one and two in FRNY 2182. Ensure that while working in the fume hoods (regardless of whether it contains a vacuum line) the sash is at least at the minimum working height! This minimizes exposure to the chemicals as well as projectiles from explosion/implosion of vacuum line vessel in case of breach. Personal Protective Equipment (while using fume hood/vacuum line) EYE PROTECTION: Safety glasses (or face shield if desired) PROTECTIVE CLOTHING: Laboratory coat, gloves (nitrile/neoprene), for freeze-pump-thaw use cryo gloves (orange gloves located above the oven) ENGINEERING CONTROL: Keep hood sash at the minimum working height. NEVER raise the sash above this level if there is any reaction in the hood. 1 Use of the Schlenk Line 1. Ensure that the vacuum pump is on (the switch is located on the back of the pump, which is in the cabinet under the hood), the cabinet door is open, and the compressed cylinder gas is not empty (i.e., the regulator supply pressure to the desired fumehood is 0.5 bar at all times, refer to Appendix 2 & 3).
    [Show full text]