WOOD POLISH FRENCH POLISH Traditional French polishes are used to obtain an impressive deep gloss and smooth finish on good quality furniture. The SHEENLAC polishes are to the same meticulous time proven method that has been used for centuries. French polish produces a warm, dark transparent coating which cannot be reproduced by modern synthetic lacquers. These products are made from pure natural to give good clarity, build and ease of application.

RECOMMENDED USE

Suitable for French Polishing on all dark and light colored interior , when a light to medium brown tone is required. Suitable for sealing pores before waxing.

FEATURES & BENEFITS:

Ÿ Provides a traditional high gloss French polish finish. Ÿ Contains only natural pure shellac. Ÿ Can be used on all untreated previously varnished or French polished woodwork or furniture. TECHNICAL DATA

Appearance – Low viscous liquid. Storage & Packing Color – Straw yellow to light brown. Can be mixed To be stored in a cool, dry & well ventilated place away from with to produce matching stains and moisture, heat and direct sunlight. stain finishes Packaging Odour – Characteristic Ketone odour.

Solubility – Immiscible with water.

Finish – Glossy 200ml 500ml 1 L 3 L 5 L 10 L 20 L Gloss level (60° head) – Min 85

VOC – 650 gm/ ℓ

Flash Point – above 12 °C

Theoretical spreading rate – 10-12 m²/ℓ per coat. This serves as a guide only.

Practical spreading rate – The practical spreading rate will vary depending on the porosity and profile of the substrate, as well as the application technique and used.

Shelf Life – 18 months from the date of production in unopened condition and, stored at the recommended storage condition.

INSPIRING CREATIVITY APPLICATION DETAILS

SURFACE PREPARATION: All wood surfaces must be clean, Application Method: firm and dry. Remove any oil, grease, mortar droppings, etc. Ÿ Wrap a piece of cotton wool inside a lint free rag to form NEW WOOD: Sand in the direction of the grain, to a smooth a pad or ‘Rubber’. finish with 150 followed by 220 grit paper. Remove dust with a Ÿ Wearing suitable gloves, pour SHEENLAC French Polish damp cloth. onto the cotton wool then squeeze the Rubber to release PREVIOUSLY VARNISHED WOOD IN GOOD any excess. CONDITION: Sand to obtain a smooth surface using 150 grit Ÿ Work the polish into the surface using a figure of eight emery paper. Remove all sanding dust using a vacuum or cloth motion. dampened with mineral spirits. Ÿ Apply several coats until the required finish is achieved, PREVIOUSLY VARNISHED WOOD IN POOR allowing 15-20 minutes between coats. CONDITION: Strip completely by deep sanding or by using Sheenlac Remover. Rinse thoroughly with clean water. Deep sand to until there is no evidence of any residue. Remove Drying Time Allow at least 24 hrs for final coat to dry dust with a damp cloth. (@ 30°C & 60 R/H) WOOD PREVIOUSLY COATED WITH SEALER/OIL BASED WOOD PRESERVATIVE: Mechanically sand until there is no evidence of residue. Clean up: Cloths and soiled rags may self-ignite without warning. Wash out well in warm soapy water before Remove dust with a damp cloth. disposal. Remove as much product as possible from PREVIOUSLY PAINTED WOOD: Strip old paint by deep application equipment prior to cleaning. sanding or by using Sheenlac Paint Remover. Rinse thoroughly with clean water. Sand bare wood to a smooth finish. Remove dust with a damp cloth. HEALTH & SAFETY INSTRUCTIONS: FILLER: If required use Sheenlac NC or Oil based Wood filler. Ÿ Always keep paint out of reach of children. Allow to dry for 24 h and remove the excess using 220 grit Ÿ Ensure good ventilation during application and drying. Emery paper and wipe with dry cloth. Ÿ If accidental contact with skin should occur, wash STAIN THE WOOD: Adding stain to bare or stripped wood immediately with soap and water. can both change the color and highlight the grain pattern of any interior wood but this is an optional. Apply Sheenlac SB Ÿ Take care to avoid contact with the eyes. In case of Wood stains by rubbing or brushing against the direction of the contact, immediately rinse the eyes with plenty of water and seek medical attention. grain will help fill deep pores with stain. Apply a liberal amount of stain, giving the wood an ample amount to absorb. Allow to Ÿ Harmful if swallowed. Seek medical attention and do not dry for 30-60 mins. induce vomiting. Ÿ Do not smoke while painting. Ÿ Flammable. Store in a cool dry place away from heat and Application Surface Ambient Relative sparks. Environment Temperature Temperature Humidity Ÿ Refer to Material Safety Data Sheet for complete Min 20 °C 20 °C 20% information. Max 30 °C 35 °C 85%

For product related queries, feedback and quality complaints, Regd. Office: Sheenlac Ltd. please contact: Old No. 109B, New No.124, Developed Plots, SIDCO Industrial Customer care: +91 8300 03 04 04 Estate, Ambattur, Chennai - 600098. Email:[email protected], Web: www.sheenlac.in

DISCLAIMER: The recommendations contained herein are given in all good faith and are meant to guide the specifier or the user. They are based on results gained from our tests and experiences and are believed to be reliable. No guarantee is implied by the recommendations contained herein since conditions of use, method of application and cleanliness of the substrate prior to painting are beyond our control. As application, environmental and design factors can vary, due care should be exercised in the selection and verification of the performance and use of the coating N.B: Technology may change with time necessitating changes to this Technical Data Sheet (TDS). It is the responsibility of the user to ensure that the latest TDS is being used Ver.1.0/TDS/2017

INSPIRING CREATIVITY