DOCSLIB.ORG

A Conceptual Design for Load Triggering by Extracting Power from the Conventional Wireless Signal with Frequency Matched to Ism Band (2.4 Ghz)

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
A Conceptual Design for Load Triggering by Extracting Power from the Conventional Wireless Signal with Frequency Matched to Ism Band (2.4 Ghz) International Journal of Mechanical Engineering and Technology (IJMET) Volume 9, Issue 5, May 2018, pp. 725–732, Article ID: IJMET_09_05_080 Available online at http://iaeme.com/Home/issue/IJMET?Volume=9&Issue=5 ISSN Print: 0976-6340 and ISSN Online: 0976-6359 © IAEME Publication Scopus Indexed A CONCEPTUAL DESIGN FOR LOAD TRIGGERING BY EXTRACTING POWER FROM THE CONVENTIONAL WIRELESS SIGNAL WITH FREQUENCY MATCHED TO ISM BAND (2.4 GHZ) V. Prabhakaran Research Scholar, Saveetha School of Engineering, Saveetha Institute of Medical and Technical Sciences, Chennai, India Dr. P. Shankar Principal, Aarupadai Veedu Institute of Technology, Chennai, India Dr. P.C. Kishore Raja Professor and Head, Department of Electronics and Communication Engineering, Saveetha School of Engineering, Saveetha Institute of Medical and Technical Sciences, Chennai, India ABSTRACT In recent scenario, the usage of Non-renewable sources is tremendously aggregated to meet the ever increasing load demand. Though renewable sources are used as a supplement, still the load demand cannot be matched. In this paper, a new conceptual inverter design is formulated which powers the load through conventional wireless signals (ISM Band – 2.4 GhZ) by a novel “Rectenna design” with an output amplification factor of (~7 times) than input signal. This design is simulated in MATLAB and the output factors are analyzed for ISM (Industrial, Scientific and Medical Radio) band signals. Keywords: Rectenna Design, Boost Converter, ISM band signals, Inverter Cite this Article: V. Prabhakaran, Dr. P. Shankar and Dr. P.C. Kishore Raja, A Conceptual Design for Load Triggering by Extracting Power from the Conventional Wireless Signal with Frequency Matched to ISM Band (2.4 GHZ), International Journal of Mechanical Engineering and Technology, 9(5), 2018, pp. 725–732. http://iaeme.com/Home/issue/IJMET?Volume=9&Issue=5 http://iaeme.com/Home/journal/IJMET 725 [email protected] A Conceptual Design for Load Triggering by Extracting Power from the Conventional Wireless Signal with Frequency Matched to ISM Band (2.4 GHZ) 1. INTRODUCTION 1.1. About Wireless Power Transfer It is a higher order concept of transferring power without any physical contact or only by using air as a medium of transfer. The medium of concern is basically of time varying components like light waves, electric, magnetic or electromagnetic fields. Wireless Power Transfer (WPT) tumbles into two major categories viz. Radiative and Non-Radiative techniques, which is concerned for far and near fields respectively. In Non-Radiative techniques (Near field), the power is transferred by the means of magnetic fields which mainly uses inductive coupling between coils of wire or by means of electric fields which uses capacitive coupling between metal electrodes since the area is within 1 wavelength of the antenna (transmitting element). Non-radiative applications include charging of smartphones, electric toothbrushes, RIFD tags, artificial cadiac pacemakers or electric automotive etc. In radiative technique (Far Field), the power is transferred by the beams of electromagnetic radiations like microwaves or laser beams since the area is beyond 1 wavelength of the antenna (transmitting element). Radiative application includes solar power satellites, confined beam energy transfer, wireless powered drone aircraft, etc. Different Technologies dealt with the wireless power transfer (WPT) with its operating frequency, transmitting element and applications are listed below. Table 1 Technologies for Wireless Power Transfer (WPT) Technology Frequency Range Transmitting Element Applications Induction stovetops and Inductive Coupling Hz-Mhz Wire Coils Industrial heaters, Electric tooth brush, etc. Portable devices charging, Tuned Coils, Lumped Resonant inductive coupling kHz – Ghz biomedical implants, element resonators MAGLEV, RFID, etc. Power routing in large- Capacitive Coupling kHz-MHz Metal Plate electrodes scale integrated circuits, Smartcards, etc Charging automotive, Magnetodynamic coupling Hz Rotating Magnets biomedical implants, vehicle Parabolic Dishes, Phased Solar power satellite, Microwaves Ghz arrays powering drone aircraft. Powering space elevator Light Waves >= THz Lasers, photocells, lenses climbers, Powering heavy duty remote applications 1.1.1. Basic Sketch of Wireless Power System Figure 1 Basic of wireless power systems http://iaeme.com/Home/journal/IJMET 726 [email protected] V. Prabhakaran, Dr. P. Shankar and Dr. P.C. Kishore Raja 1.1.2. Enlightenment on Wireless Power System In a basic wireless power system “Transmitter” is connected to a power source commonly called as main power line, in which the conversion of power to a time-varying electromagnetic field is formulated. These generated oscillating wave fronts are transmitted wirelessly in air as an operating medium. In the receiving end these oscillating wave fronts is received by a dedicated receiver in which the conversion of oscillating wave fronts to electrical current is formulated. Wireless power transfer uses the same field and waves as wireless communication devices like radio, mobile phones, WiFi uses. 2. RECTENNA DESIGN In the recent scenario recycling of energy has become a mojor significant issue across the globe. Even though many research advancements are in-forced on renewable and non- renewable energy technologies for better utilization of the energy to full fill the energy crises, the wastage of energy in some form are always a big deal to minimize. In recent years, the advancement in wireless systems has an increased mass interest among the people because of its attractive merits. Many applications ranging from communication, data transfer, sensing, authentication, security, etc are becoming seamlessly possible in all field including industry, domestic, military & space research. However, making the world into wireless is now in reality but transferring energy wirelessly is the challenging task. Research evidence from 1960’s shows transferring power wirelessly is distance limited within a shorter range, which follows few eminent methods like inductive coupling, resonant inductive coupling, capacitive coupling and magnetic coupling. Later the usage of microwaves and light waves are used for better improvement in their range of access. Today’s top notch of the technology is the Mobile communication which uses high range of radio waves called microwaves for their operations. These are the derivative of electromagnetic waves which are radiated by the signal towers of the service provider. Despite of higher bandwidth the signal towers radiates intense EM waves which cause adverse effect on humans. In this paper an inverter model is designed with a depicted Rectenna module which converts the radio signal into electrical signal which is fedded to the inverter module to power up the load. Rectenna design is formulated in MATLAB under Simulink environment and the output is analyzed. In addition, an inverter model is also formulated which powers the load connected to it. 2.1. Simple Rectenna module Figure 2 Simple Rectenna Design A rectenna is a special type of antenna designed for the effective conversion of electromagnetic energy into direct current (DC) electricity. The basic design consists of dipole antenna with a diode connected across the dipole element. Normally schoktty diode is used for the better rectification because of it fast switching characteristics and lowest voltage drop which eventually have lowest power losses. This diode converts the AC current (EM Waves) into DC current which powers the load connected across to it. http://iaeme.com/Home/journal/IJMET 727 [email protected] A Conceptual Design for Load Triggering by Extracting Power from the Conventional Wireless Signal with Frequency Matched to ISM Band (2.4 GHZ) 2.2. Types of Rectenna Design There are many types of rectenna design such as microstrip antenna, Yagi-Uda antenna, Monopole antenna, coplanar patch antenna, spiral antenna or sometimes parabolic antenna. It can also have any type of rectification circuit such as single shunt full-wave rectifier, full- wave bridge rectifiers of any other hybrid rectifiers. The conversion efficiency if formulated approximately 90% with a power output upto 8W for the input of 2.45 GHz (ISM) band. Rectenna rejects the harmonics upto 3rd order and enhance the performance characteristics. Many eminent Rectenna Design with its output power and conversion ratio is formulated under the table below. Table 2 Formulation of Conversion efficiency for various Antenna Designs RF/DC S.No Rectenna Design Input Frequency Output power Conversation Efficiency 1 Dipole Element 868 MHz 0.705 mW 49.7% 2 Conformal Antenna 2 GHz 1.2 mW 51% Microstrip Antenna 1.88 GHz to 2.45 3 20.23 mW 65% (LTE/WLAN) GHz ISM Band (2.45 4 Compact Planar Antenna 1.2 W 75% GHz) 5 Dual Polarized Rectenna 8.51 GHz 3.5 W 86% 6 Rhombic Loop Antennas 2.45 GHZ 7.5 w 91% 2.3. Rectenna in MATLAB Simulink Environment The basic rectenna design essentially contains a signal receiving unit (Dipole Antenna) and rectification circuit (Schotty Diode). These elements are depicted in MATLAB Simulink environment as Signal Generator and diode rectifiers which acts as a source for power production. The signal generator is made to fix with a value of 2.4 GhZ so as to act as a commercial ISM frequency band. This frequency from the signal generator is converted into electrical signal via diode rectifiers and then it is boosted to a higher value with an eminent “Interleaved Boost Converter”. The concept of interleaving
Load more

Recommended publications
  • A Wideband Conformal Antenna with High Pattern Integrity for Mmwave 5G Smartphones
    Progress In Electromagnetics Research Letters, Vol. 84, 1–6, 2019 A Wideband Conformal Antenna with High Pattern Integrity for mmWave 5G Smartphones Gulur S. Karthikeya*,MaheshP.Abegaonkar,andShibanK.Koul Abstract—In this paper, a co-planar waveguide fed circular slot antenna with an operational impedance bandwidth of 20–28 GHz is proposed. In order to reduce the effective occupied volume when the antenna is integrated onto a typical mmWave 5G smartphone, a conformal topology is investigated. Since the radiating aperture is not backed by an electrically large ground plane, it leads to a bidirectional beam resulting in an inherently low forward gain of 4 dBi with a front to back ratio of 1 dB. Hence, a compact exponentially tapered copper film reflector is integrated electrically close (0.046λ at 28 GHz) to the radiating aperture to achieve a forward gain of 8–9 dBi with an effective radiating volume of 0.24λ3. The impedance bandwidth is from 25 to 30 GHz (18.2%) with a 1-dB gain bandwidth of 34.7% indicating high pattern integrity across the band. Since the proposed antenna element offers wideband with high gain, it is a potential candidate for mmWave 5G smartphones. 1. INTRODUCTION The phenomenal growth in the smartphone users over the years has provoked researchers in academia and industry to design future-proof transceivers facilitating high data-rates, which in turn need high carrier frequencies, such as 28 GHz band. The 28 GHz band is projected as a potential candidate for future 5G cellular communication systems. The fundamental challenge for deployment of 28 GHz radios is the inherent high path loss.
    [Show full text]
  • Conformal Microstrip Printed Antenna
    Conformal microstrip printed antenna K. Elleithy H. Bajwa A. Elrashidi ([email protected]) ([email protected]) ([email protected]) University of Bridgeport 126 Park Avenue Bridgeport, CT 06604 Abstract 4. With planer arrays the radiation pattern changes In this paper, the comprehensive study of the with the direction of scan, while conformal arrays conformal microstrip printed antenna is presented. The main with rotational symmetry (cylindrical profile) can advantages and drawbacks of a microstrip conformal have scan-invariant pattern [5]. antenna are introduced. The earlier researches in cylindrical- 5. Cylindrical conformal gives nearly Omni- rectangular patch and conformal microstrip array are directional radiation pattern [6]. summarized. The effect of curvature on the conformal 6. It gives large angle coverage. Microstrip antenna patch on conical and spherical surfaces is studied. Some new flexible antenna is given for different Because of the advantages of conformal antennas, it is very frequencies. Finally, simulation software is used to study the popular in the different flight aircrafts [7]. effect of the curvature on the input impedance, return loss, On the other side, a conformal microstrip antenna has some voltage standing wave ratio, and resonance frequency. drawbacks due to bedding [8], those drawbacks are illustrated below: Keywords: Microstrip antenna, conformal antenna, Printed 1. The dielectric material will undergo stretching and antenna, resonance frequency, curvature, input impedance, compression along the inner and outer surfaces, return loss, and voltage standing wave ratio. respectively. Stretching of copper traces will result in phase, impedance, and resonance frequency 1. Introduction error. 2. Shaping the material can also result in a change in Microstrip antennas have been widely studied in recent both the dielectric constant and material thickness.
    [Show full text]
  • Experimental Demonstration of Conformal Phased Array Antenna
    www.nature.com/scientificreports OPEN Experimental demonstration of conformal phased array antenna via transformation optics Received: 2 November 2017 Juan Lei1,2, Juxing Yang1, Xi Chen1, Zhiya Zhang1, Guang Fu1 & Yang Hao2 Accepted: 9 February 2018 Transformation Optics has been proven a versatile technique for designing novel electromagnetic Published: xx xx xxxx devices and it has much wider applicability in many subject areas related to general wave equations. Among them, quasi-conformal transformation optics (QCTO) can be applied to minimize anisotropy of transformed media and has opened up the possibility to the design of broadband antennas with arbitrary geometries. In this work, a wide-angle scanning conformal phased array based on all-dielectric QCTO lens is designed and experimentally demonstrated. Excited by the same current distribution as such in a conventional planar array, the conformal system in presence of QCTO lens can preserve the same radiation characteristics of a planar array with wide-angle beam-scanning and low side lobe level (SLL). Laplace’s equation subject to Dirichlet-Neumann boundary conditions is adopted to construct the mapping between the virtual and physical spaces. The isotropic lens with graded refractive index is realized by all-dielectric holey structure after an efective parameter approximation. The measurements of the fabricated system agree well with the simulated results, which demonstrate its excellent wide- angle beam scanning performance. Such demonstration paves the way to a robust but efcient array synthesis, as well as multi-beam and beam forming realization of conformal arrays via transformation optics. Phased array antennas have received increasing attention in recent years for applications in modern wireless com- munications and radar systems etc.
    [Show full text]
  • Design and Characterization of Circularly Polarized Cavity-Backed Slot Antennas in an In-House-Constructed Anechoic Chamber
    Utah State University DigitalCommons@USU All Graduate Theses and Dissertations Graduate Studies 8-2012 Design and Characterization of Circularly Polarized Cavity-Backed Slot Antennas in an In-House-Constructed Anechoic Chamber Mangalam Chandak Utah State University Follow this and additional works at: https://digitalcommons.usu.edu/etd Part of the Electrical and Computer Engineering Commons Recommended Citation Chandak, Mangalam, "Design and Characterization of Circularly Polarized Cavity-Backed Slot Antennas in an In-House-Constructed Anechoic Chamber" (2012). All Graduate Theses and Dissertations. 1265. https://digitalcommons.usu.edu/etd/1265 This Thesis is brought to you for free and open access by the Graduate Studies at DigitalCommons@USU. It has been accepted for inclusion in All Graduate Theses and Dissertations by an authorized administrator of DigitalCommons@USU. For more information, please contact [email protected]. DESIGN AND CHARACTERIZATION OF CIRCULARLY POLARIZED CAVITY-BACKED SLOT ANTENNAS IN AN IN-HOUSE-CONSTRUCTED ANECHOIC CHAMBER by Mangalam Chandak A thesis submitted in partial fulfillment of the requirements for the degree of MASTER OF SCIENCE in Electrical Engineering Approved: Dr. Reyhan Baktur Dr. Edmund Spencer Major Professor Committee Member Dr. Jacob Gunther Dr. Mark R. McLellan Committee Member Vice President for Research and Dean of the School of Graduate Studies UTAH STATE UNIVERSITY Logan, Utah 2012 ii Copyright c Mangalam Chandak 2012 All Rights Reserved iii Abstract Design and Characterization of Circularly Polarized Cavity-Backed Slot Antennas in an In-House-Constructed Anechoic Chamber by Mangalam Chandak, Master of Science Utah State University, 2012 Major Professor: Dr. Reyhan Baktur Department: Electrical and Computer Engineering Small satellites are satellites that weight less than 500 kg.
    [Show full text]
  • A Deeply Implantable Conformal Antenna for Leadless Pacing Applications
    A Deeply Implantable Conformal Antenna for Leadless Pacing Applications S. M. Asif A. Iftikhar B. D Braaten & D. L. Ewert K. Maile Electronic & Electrical Engineering Electrical Engineering Electrical & Computer Eng. Boston Scientific Corp. The University of Sheffield COMSATS Institute of IT North Dakota State University 4100 Hamline Ave N Sheffield, S1 4ET, UK Islamabad, Pakistan Fargo, ND, USA St. Paul, MN, USA [email protected] [email protected] [email protected] [email protected] [email protected] Abstract—Finite battery life and complications caused by leads of conventional pacemakers are key issues in pacemaker tech- nology. In this paper, we propose a deeply implantable antenna which can be conformed on a commercially available leadless pacemaker and has the potential capability of receiving and harvesting radio frequency (RF) energy to achieve cardiac pacing. More specifically, a deeply implantable conformal antenna at 2.45 GHz has been designed in ANSYS HFSS and then manufactured and integrated with a 3D printed mock pacemaker. The antenna performance was measured in tissue simulating liquid (TSL) and good agreement was achieved with the simulation results. Moreover, it was concluded that the proposed conformal antenna design on a commercially available pacemaker has the potential to be integrated with a rectifier for leadless pacing. I. INTRODUCTION Modern Cardiac Resynchronization Therapy devices such as pacemakers do not only stimulate the myocardium of the heart to correct its rhythm but also performs other important functions such as implementation of algorithms, obtaining measurements of diagnostic data and other sensors [1]. These devices have the ability to improve the wellbeing of the patients and the potential to increase the life expectancy.
    [Show full text]
  • Design and Simulation of Fully Printable Conformal Antennas with BST/Polymer Composite Based Phase Shifters
    Progress In Electromagnetics Research C, Vol. 62, 167–178, 2016 Design and Simulation of Fully Printable Conformal Antennas with BST/Polymer Composite Based Phase Shifters Mahdi Haghzadeh1, Hamzeh Jaradat2, Craig Armiento1, and Alkim Akyurtlu1, * Abstract—A fully printable and conformal antenna array on a flexible substrate with a new Left- Handed Transmission Line (LHTL) phase shifter based on a tunable Barium Strontium Titanate (BST)/polymer composite is proposed and computationally studied for radiation pattern correction and beam steering applications. First, the subject 1 × 4 rectangular patch antenna array is configured as a curved conformal antenna, with both convex and concave bending profiles, and the effects of bending on the performance are analyzed. The maximum gain of the simulated array is reduced from the flat case level by 34.4% and 34.5% for convex and concave bending, respectively. A phase compensation technique utilizing the LHTL phase shifters with a coplanar design is used to improve the degraded radiation patterns of the conformal antennas. Simulations indicate that the gain of the bent antenna array can be improved by 63.8% and 68% for convex and concave bending, respectively. For the beam steering application, the proposed phase shifters with a microstrip design are used to steer the radiation beam of the antenna array, in planar configuration, to both negative and positive scan angles, thus realizing a phased array antenna. 1. INTRODUCTION Printed flexible electronics is a promising approach for developing electronic and electromagnetic subsystems with different form factors. The potential advantages of printed electronics include ultra-low cost, rapid prototyping, low temperature processing, and roll-to-roll manufacturing on flexible plastic substrates.
    [Show full text]
  • Design and Optimization of Conformal Dielectric Resonator Antenna Array Based on Aperture-Coupled Series-Feeding Approach
    Progress In Electromagnetics Research C, Vol. 109, 53–64, 2021 Design and Optimization of Conformal Dielectric Resonator Antenna Array Based on Aperture-Coupled Series-Feeding Approach Hongmei Liu*, Yue Niu, Tielin Zhang, Shaojun Fang, and Zhongbao Wang Abstract—A novel conformal dielectric resonator antenna (DRA) array based on aperture-coupled series-feeding approach is presented for wireless communication. The antenna is composed of eight curved width-gradated DRA elements with a simple feeding structure. The proposed design presents a tapered current amplitude distribution by using DRA element width gradation method, and low side-lobe level (SLL) characteristic can be obtained. Besides, an extra matching line is inserted into the single feeding line to realize better impedance characteristic. To validate the performance of the proposed design, the conformal array is fabricated and measured in an anechoic chamber. The measured impedance bandwidth (|S11| < −10 dB) of the fabricated prototype is from 5.78 GHz to 5.87 GHz. At 5.8 GHz, the antenna offers a measured peak gain of 14.75 dBi and SLL of −19.3 dB. The polarization discriminations of the array on E-andH-planes are greater than 20 dB. The measured results of the fabricated prototype demonstrate that the proposed design has the potential to be applied to wireless communication system with curved surface. 1. INTRODUCTION Dielectric resonator antenna (DRA) can be considered as a successful candidate for wireless communication, especially in the microwave and millimeter frequency bands, owing to its inherent advantages of compact size, high power handling capability, low conduction losses, and high radiation efficiency [1–3].
    [Show full text]
  • Two Types of Conformal Antennas for Small Spacecrafts
    Utah State University DigitalCommons@USU All Graduate Theses and Dissertations Graduate Studies 5-2015 Two Types of Conformal Antennas for Small Spacecrafts Salahuddin Tariq Utah State University Follow this and additional works at: https://digitalcommons.usu.edu/etd Part of the Electrical and Computer Engineering Commons Recommended Citation Tariq, Salahuddin, "Two Types of Conformal Antennas for Small Spacecrafts" (2015). All Graduate Theses and Dissertations. 4266. https://digitalcommons.usu.edu/etd/4266 This Thesis is brought to you for free and open access by the Graduate Studies at DigitalCommons@USU. It has been accepted for inclusion in All Graduate Theses and Dissertations by an authorized administrator of DigitalCommons@USU. For more information, please contact [email protected]. TWO TYPES OF CONFORMAL ANTENNAS FOR SMALL SPACECRAFTS by Salahuddin Tariq A thesis submitted in partial fulfillment of the requirements for the degree of MASTER OF SCIENCE in Electrical Engineering Approved: Dr. Reyhan Baktur Dr.Charles M. Swenson Major Professor Committee Member Dr. Jacob Gunther Dr. Mark R. McLellan Committee Member Vice President for Research and Dean of the School of Graduate Studies UTAH STATE UNIVERSITY Logan, Utah 2015 ii Copyright c Salahuddin Tariq 2015 All Rights Reserved iii Abstract Two Types of Conformal Antennas for Small Spacecrafts by Salahuddin Tariq, Master of Science Utah State University, 2015 Major Professor: Dr. Reyhan Baktur Department: Electrical and Computer Engineering Conformal antennas have widespread applications in communication systems for vehic- ular bodies, aircrafts, and spacecrafts etc. They are non-protruding and can arbitrarily take any shape on the surface where they are etched. This thesis is a summary of two main projects.
    [Show full text]
  • Flexible, Conformal Phased Arrays with Dynamic Array Shape Self- Calibration
    Flexible, Conformal Phased Arrays with Dynamic Array Shape Self- Calibration Austin C. Fikes 1, Amirreza Safaripour, Florian Bohn, Behrooz Abiri, and Ali Hajimiri Caltech Holistic Integrated Circuits Lab, Caltech, Pasadena, CA 91011, USA [email protected] Abstract— Flexible and conformal phased arrays enable a mechanical resistive sensors are used to measure shape broad range of novel applications. One of the major challenges for deformation. The sensors add an additional interface, such systems is that they experience a change in their behavior significantly increasing the complexity of the overall system. when bent or deformed. A self-calibrating flexible phased array These drawbacks limit the scalability of the array and prevent can overcome this by estimating the relative position change of its generic arrays from adopting the calibration scheme. elements as they undergo local deformations. In this work, we demonstrate a dynamically flexible and conformal 8-element This work presents a flexible 8-element array with transmit phased array based on a custom CMOS transceiver unit. Beam- and receive capability and proposes a self-contained shape steering is demonstrated with the flexible array flat and with the calibration method using only the coupling between elements array conformed to convex and concave bend radii of ±120 mm. in the array. By using the transmit and receive capability to In addition, we propose and test a shape calibration method that measure the coupling between elements in the array, uses only the coupling between elements, using the flexible phase mechanical deformation of the array is measured. array. Keywords—flexible electronics, phased array, integrated II. FLEXIBLE PHASED ARRAY circuits, integrated circuits, calibration.
    [Show full text]
  • Conformal Phased Array with Beam Forming for Airborne Satellite Communication
    CONFORMAL PHASED ARRAY WITH BEAM FORMING FOR AIRBORNE SATELLITE COMMUNICATION H. Schippers ([email protected]), J. Verpoorte , P. Jorna, A. Hulzinga (National Aerospace Laboratory NLR, Amsterdam), A. Meijerink, C. Roeloffzen, (University of Twente, Enschede), R.G.Heideman, A. Leinse, (LioniX bv, Enschede), M. Wintels (Cyner Substrates, Utrecht) ABSTRACT • Electronically steered phased array antennas (see Figure For enhanced communication on board of aircraft novel 7). antenna systems with broadband satellite-based capabilities • Hybrid steered antennas; such antennas are normally are required. The installation of such systems on board of mechanically steered in one direction (e.g. azimuth), aircraft requires the development of a very low-profile and electronically in the other direction (e.g. elevation). aircraft antenna, which can point to satellites anywhere in the upper hemisphere. To this end, phased array antennas which are conformal to the aircraft fuselage are attractive. In this paper two key aspects of conformal phased array antenna arrays are addressed: the development of a broadband Ku-band antenna and the beam synthesis for conformal array antennas. The antenna elements of the conformal array are stacked patch antennas with dual linear polarization which have sufficient bandwidth. For beam forming synthesis a method based on a truncated Singular Value Decomposition is proposed. 1. INTRODUCTION Figure 1 Mechanically steered reflector antenna For enhanced communication on board of aircraft novel antenna systems with broadband satellite-based capabilities Mechanically steered reflector and array antennas are required. The technology must bring live weather reports require a large radome for reasons of protection and to pilots, as well as live TV and high-speed Internet aerodynamic behaviour.
    [Show full text]
  • Structural-Electromagnetic Simulation Coupling and Conformal Antenna Design Tool by © 2018 Pedro Martin Mendoza Strilchuk B.S., University of Kansas, 2015
    Structural-Electromagnetic Simulation Coupling and Conformal Antenna Design Tool By © 2018 Pedro Martin Mendoza Strilchuk B.S., University of Kansas, 2015 Submitted to the graduate degree program in Aerospace Engineering and the Graduate Faculty of the University of Kansas in partial fulfillment of the requirements for the degree of Master of Science. Chair: Dr. Emily J. Arnold Dr. Richard D. Hale Dr. Ronald M. Barrett-Gonzales Date Defended: March 15, 2018 ii The thesis committee for Pedro Martin Mendoza Strilchuk certifies that this is the approved version of the following thesis: Structural-Electromagnetic Simulation Coupling and Conformal Antenna Design Tool Chair: Dr. Emily J. Arnold Date Approved: April 26, 2018 iii Abstract Airborne and spaceborne radar has long been an effective tool for remote sensing, surveillance, and reconnaissance. Most airborne systems utilize antenna arrays that are installed inside the moldline of the aircraft or in radomes that protect the array from in-flight loads. While externally-mounted arrays can offer the advantage of larger apertures, sensor-vehicle interactions often result in performance degradation of both systems. The presence of an externally-mounted array will increase the vehicle’s drag and potentially affect the dynamics and control of the vehicle. In addition, in-flight structural loads will deform the array, thus resulting in relative phase errors. While there exist a multitude of physics-based simulation tools to determine the effects of the array on the aircraft performance, existing tools are not sufficient for generating deformed arrays necessary for determining in-flight array performance. In response to this need, a computer tool for analyzing antennas undergoing structural loads is developed.
    [Show full text]
  • Gain Limits of Phase Compensated Conformal Antenna Arrays on Non-Conducting Spherical Surfaces Using the Projection Method
    WiSEE 2013 1569798205 Gain Limits of Phase Compensated Conformal Antenna Arrays on Non-Conducting Spherical Surfaces using the Projection Method Bilal Ijaz, Alarka Sanyal, Alfonso Mendoza-Radal, Neil F. Chamberlain Dimitris E. Anagnostou Sayan Roy, Irfan Ullah, Michael T. Reich, Jet Propulsion Laboratory (JPL) Department of Electrical Debasis Dawn and Benjamin D. Braaten California Institute of Technology and Computer Engineering Department of Electrical and Computer Engineering Pasadena, CA, USA 91109. South Dakota School of North Dakota State University Mines and Technology, Fargo, ND, USA 58102 Rapid City, SD USA 57701 Email: [email protected] Abstract—Previously, it has been shown that the projection method can be used as an effective tool to compute the ap- propriate phase compensation of a conformal antenna array on a spherical surface. In this paper, the projection method is used to study the gain limitations of a phase-compensated six- element conformal microstrip antenna array on non-conducting spherical surfaces. As a metric for comparison, the computed gain of the phase-compensated conformal array is compared to the gain of a six-element reference antenna on a flat surface with the same inter-element spacing and operating frequency. To validate these computations, a conformal phased-array antenna consisting of six individual microstrip patches, voltage controlled Fig. 1. Array on a conformal surface. phase shifters and a power divider was assembled and tested at 2.22 GHz. Overall, it is shown how much less the gain of the phase-compensated antenna is than the reference antenna for various radius values of the sphere. Index Terms—conformal antenna array, phase compensation.
    [Show full text]