DOCSLIB.ORG

DESIGN of WISHBONE INTERFACED I2CMASTER CORE CONTROLLER USING VERILOG Ramesh Babu Dasara1, Y

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
DESIGN of WISHBONE INTERFACED I2CMASTER CORE CONTROLLER USING VERILOG Ramesh Babu Dasara1, Y DESIGN OF WISHBONE INTERFACED I2CMASTER CORE CONTROLLER USING VERILOG Ramesh Babu Dasara1, Y. Chandra Sekhar Reddy2 1Pursuing M.tech, 2Assistant Professor, from Nalanda Institute of Engineering and Technology (NIET), Siddharth Nagar, Kantepudi village, Sattenepalli Mandal, Guntur Dist.,A.P. (India) ABSTRACT In this paper we are implementing one of the serial communication protocol called Inter integrated circuit (I2C) master controller. The protocol is made of set of standards with the master and slave configuration to allow data transfer. The I2C master with wishbone controller is implemented in Verilog HDL. The modules are synthesized in Xilinx 13.2i. Then simulated to observe the operation of the Master controller and wishbone controller which performs high speed data transfer in presence of master or slave. This yields higher speed data transfer over the network. Keywords: Master,Wishbone, SDA,SCK,SLAVE I. INTRODUCTION In electronic world to make communication between any two digital hardware devices needs serial communication standards. There are several communication standards are RS232, RS435, and SPI to make high speed and low speed data transfer. To implement protocols actually we require more number of pin connections, whereas the size of IC gradually decreasing so we need a protocol that can have minimum number of pin connections. The protocols existed earlier are SPI, MOCROWIRE and USB needs point to point connection such that needs multiplexing of data and address. The proposed protocol requires only two lines two communicate with nay number of devices while other needs more number of pin connections. The I2c is best suited for medium range communication between the circuit boards within the equipment. This is also used for control applications where certain device to be added and removed. The I2C is also used to communicate between the circuits using a cable or without cable. The I2C will have master and slave, the master whichsends data to slave will generate responses based on master controller signals. II. I2CPROTOCOL The I2C is vital for implementing low a data rate communications. The I2C bus made of bidirectional lines with pull up resistors. I2c will allow data transfer between many devices. It will allow us to connect certain devices to it with each and unique address to identify them. The data and address are the inputs to the controller, the external inputs clk ,rst which starts the data transfer. The r/w signal is used to indicate which in transmission either master or slave. 151 | P a g e Fig 2.1 SDA AND SCK The physical I2C bus consists of simply 2 wires,called SCL and SDA. SCL is that the clock line. It is used to synchronize all information transfers over the I2C bus. SDA is that the information line. The SCL and SDA lines are connected to all or any devices on the I2C bus. As both SCL and SDA lines square measure "open drain" drivers they're pulled up victimisation pull up resistors. The I2C bus is claimed to be idle once each SCL and SDA square measure at logic one level. once the master (controller) desires to transmit information to a slave (DS1307) it begins by issuance a begin sequence on the I2C bus, that may be a high to low transition on the SDA line whereas the SCL line is high as shown in Fig– 2(a).The bus is taken into account to be busy once theSTART condition. once the beginning condition,slave address is distributed by the master. The slave devicewhose address matches the address that's being sent out by the master can respond with Associate in NursingMacknowledgement bit on the SDA line by propulsion the SDA line low. information is transferred in sequences of eight bits. The bits square measure placed on the SDA line beginning with the savings bank (Most vital Bit). for each eight bits transferred, the slave device receiving the info sends back Associate in Nursing acknowledge bit, therefore there are literally 9 SCL clock pulses to transfer every eight bit computer memory unit of knowledge this is shown in Fig-3. If the receiving device sends back an occasional ACK bit, then it's received the info and is prepared to simply accept another computer memory unit. If it sends back a high then it's indicating it cannot settle for from now on data and also the master ought to terminate the transfer by sending a STOP sequence. In Fig-2.1 that shows the STOP sequence, wherever the SDA line is driven low whereas SCL line is high. This signals the top of the group action with the slave device. III. PROPOSED I2C WITH WISHBONE The I2C master core supports the vital options represented within the I2C specification and is appropriate for many applicationsinvolving I2C slave management. the planning responds to the read/write cycles initiated by the microcontrollerThrough the wishing bone interface. It provides the right sequences of commands and knowledge to the I2C slave device and then transfers the specified knowledge from the I2C slave device through the 2 open-drain wires. The I2C master with wishing bone interface offloads the microcontroller from desperate to deal several details of the I2C commands and operation sequences. Table one lists the I/O ports of the planning. The signals ending in “_i” indicate Associate in Nursing input and people ending in “_o” indicatean output. All signals on wishing bone facet square measure synchronous to the master clock. the 2 I2C wires, scl and sda, should be open-drain signals and square measure outwardly force up to Vcc through resistors. 152 | P a g e Table3.1 Wishbone Signal Description The design has four main modules as shown in Figure3.1. These embrace one ranking module and 3 lower-level modules, that ar the register module, the computer memory unit module and somewhat module.In addition to connecting all the useful blocks along, this module generates byte-wide knowledge, acknowledgement, and interrupt for the wishing bone interface. reckoning on the parameter ARST_LVL, the reset polarity is determined and distributed to any or all the modules The 2bit by 8bit registers are presnet in the I2C core. This registers addresses will not be used for future reference. Table 3.2 Internal Registers The Prescale Register (address = 0x00 and 0x01) is employed to prescale the scl clock line supported the master clock. Since the planning is driven by a (5 x scl frequency) internally, the prescale register is programmed in keeping with the equation [master clock frequency / (5 x (sclk frequency)) - 1]. The content of this register will solely be changedwhen the core isn't enabled. Only 2 bits of the management Register (address = 0x01) ar used for this style. The MSB of this register is that the most critical one as a result of it allows or disables the complete I2C core. The core won't reply to any command unless this bit is ready.The Transmit Register and therefore the Receive Register share an equivalent address (address = 0x30) reckoning on the direction of information transfer. the info to be transmitted via I2C are keep within the Transmit Register, whereas the computer memory unit received via I2C is obtainable within the Receive register. The standing Register and therefore the Command Register share an equivalent address (address = 0x04). The standing Registerallows the watching of the I2C operations, whereas the Command Register stores consecutive command for consecutive I2C operation. in contrast to the remainder of the registers, the bits within the 153 | P a g e Command Register ar cleared mechanically when every operation. so this register has got to be written for every begin, write, read, or stop of the I2C operation. Table 3 provides a close description of every bit within the internal registers Fig 3.1 Block Daigram of the I2C Module State1 : AN idle condition: I2C bus doesn’t perform any operation. (SCL and SDA remains high). State2 : begin condition: master initiates information transmission by providing begin (SCL is high andSDA is from high to low). State 3 : Slave address - write: master sends theslave address-write (11010000) to the slave. State 4 : If the slave address matches with the slave, it sends AN acknowledgement bit in responseto the master. State 5 : eight Bit Register Address[12] are going to be transmitted to the slave. once more acknowledgement is sent to the master by the slave. State 6 : information to be transmitted is distributed to the slave by the master. once receiving the information, slave acknowledges the master. State seven : Stop condition: Slave sends a stop bit to the master to terminate the communication (SCL is high and SDA is from Low to high). For playacting browse operation, write operation is performed 1st then browse operation is completed. Slave address for browse is 11010001. (State seven won'tbe performed for browse operation) State eight : Master transmits slave address for browse operation to the slave. State nine : Master receives the information from the slave and acknowledges the slave. State ten : Master sends a STOP bit to terminate the connection (SCL is high and SDA is from Low to high). Fig- IV. SIMULATION RESULTS In this project we are implementing I2C master with Wish bone interface such that wishbone bus is the medium that will be used to connect between master and slave. That data which was sent by master will be given to the 154 | P a g e wishbone that will grant the permission to access the slave. There is no direct connection between the master and slave. The master and its internal Modules are designed using Verilog HDL. The modules synthesized in Xilinx ISE 13.2i.
Load more

Recommended publications
  • IOTA: Detecting Erroneous I/O Behavior Via I/O Transaction Auditing
    Appears in the First Workshop on Compiler and Architectural Techniques for Application Reliability and Security (CATARS) In Conjunction with the 2008 International Conference on Dependable Systems and Networks (DSN 2008) Anchorage, Alaska, June 2008 IOTA: Detecting Erroneous I/O Behavior via I/O Transaction Auditing Albert Meixner and Daniel J. Sorin Duke University [email protected], [email protected] Abstract nosed, the system could suggest that the user or system The correctness of the I/O system—and thus the administrator replace this device. If a driver bug is diag- nosed, the bug can be reported and the driver can be correctness of the computer—can be compromised by restarted (which is often sufficient). If a security breach hardware faults, driver bugs, and security breaches in is diagnosed, the system can shutdown the driver under downloaded device drivers. To detect erroneous I/O suspicion and alert the user. In this work, we focus on behavior, we have developed I/O Transaction Auditing error detection, rather than diagnosis and recovery. (IOTA), which checks the high-level behavior of I/O Our error detection mechanism, I/O Transaction transactions. In an IOTA-protected system, the operat- Auditing (IOTA), uses end-to-end checking [13] of I/O ing system creates a signature of the I/O transactions it transactions. We define a transaction as a high-level, expects to occur and every I/O device computes a signa- semantically atomic I/O operation, such as sending an ture of the transactions it actually performs. By compar- Ethernet frame. A transaction represents the basic I/O ing these signatures, IOTA can discover erroneous operation for higher level OS services such as the file behavior in both the hardware and the software respon- system or network stack.
    [Show full text]
  • Open Borders for System-On-A-Chip Buses: a Wire Format for Connecting Large Physics Controls
    PHYSICAL REVIEW SPECIAL TOPICS - ACCELERATORS AND BEAMS 15, 082801 (2012) Open borders for system-on-a-chip buses: A wire format for connecting large physics controls M. Kreider,1,2 R. Ba¨r,1 D. Beck,1 W. Terpstra,1 J. Davies,2 V. Grout,2 J. Lewis,3 J. Serrano,3 and T. Wlostowski3 1GSI Helmholtz Centre for Heavy Ion Research, Darmstadt, Germany 2Glyndwˆ r University, Wrexham, United Kingdom 3CERN, Geneva, Switzerland (Received 27 January 2012; published 23 August 2012) System-on-a-chip (SoC) bus systems are typically confined on-chip and rely on higher level compo- nents to communicate with the outside world. The idea behind the EtherBone (EB) protocol is to extend the reach of the SoC bus to remote field-programmable gate arrays or processors. The EtherBone core implementation connects a Wishbone (WB) Ver. 4 Bus via a Gigabit Ethernet based network link to remote peripheral devices. EB acts as a transparent interconnect module towards attached WB Bus devices. EB was developed in the scope of the WhiteRabbit Timing Project at CERN and GSI/FAIR. WhiteRabbit will make use of EB as a means to issue commands to its timing nodes and control connected accelerator hardware. DOI: 10.1103/PhysRevSTAB.15.082801 PACS numbers: 84.40.Ua, 29.20.Àc, 07.05.Àt systems hosted inside a field-programmable gate array I. PURPOSE AND ENVIRONMENT (FPGA). EtherBone was named after these underlying This article builds on the paper by the title ‘‘EtherBone—A technologies, Ethernet and Wishbone. However, EB re- network Layer for the Wishbone SoC Bus’’ in the sides in the Open Systems Interconnection session layer ICALEPCS 2011 conference proceedings and aims to pro- (OSI layer 5) and does not depend on a specific choice of vide details on design choices and performance analysis for lower layer protocols in implementation.
    [Show full text]
  • UVM Based Reusable Verification IP for Wishbone Compliant SPI Master
    UVM Based Reusable Verification IP for Wishbone Compliant SPI Master Core Lakhan Shiva Kamireddy∗, Lakhan Saiteja Ky ∗VLSI CAD Research Group, Department of Electrical and Computer Engineering, University of Colorado Boulder, CO 80303, USA, Email: [email protected] yDepartment of Electronics and Electrical Communication Engineering, Indian Institute of Technology Kharagpur West Bengal 721302, India, Email: [email protected] Abstract—The System on Chip design industry relies heavily ming, coverage analysis, constrained randomization and as- on functional verification to ensure that the designs are bug- sertion based VIP. A methodological approach for verification free. As design engineers are coming up with increasingly dense increases the efficiency and reduces the verification effort. In chips with much functionality, the functional verification field has advanced to provide modern verification techniques. In this paper, we use UVM, a System Verilog based methodology this paper, we present verification of a wishbone compliant for testing an SPI master core that is wishbone compliant. Serial Peripheral Interface (SPI) Master core using a System The paper is organized into the following sections: Section Verilog based standard verification methodology, the Universal II introduces the key features of SV and UVM environment. Verification Methodology (UVM). By making use of UVM factory In Section-III, we introduce the SPI Master IP core for pattern with parameterized classes, we have developed a robust and reusable verification IP. SPI is a full duplex communication which the UVM framework is developed. Section-IV presents protocol used to interface components most likely in embedded our approach towards the development of UVM based VIP. systems. We have verified an SPI Master IP core design that Simulation results with snapshots and a critical discussion of is wishbone compliant and compatible with SPI protocol and the limitations of the design are presented in Section-V.
    [Show full text]
  • Wishbone Bus Architecture – a Survey and Comparison
    International Journal of VLSI design & Communication Systems (VLSICS) Vol.3, No.2, April 2012 WISHBONE BUS ARCHITECTURE – A SURVEY AND COMPARISON Mohandeep Sharma 1 and Dilip Kumar 2 1Department of VLSI Design, Center for Development of Advanced Computing, Mohali, India [email protected] 2ACS - Division, Center for Development of Advanced Computing, Mohali, India [email protected] ABSTRACT The performance of an on-chip interconnection architecture used for communication between IP cores depends on the efficiency of its bus architecture. Any bus architecture having advantages of faster bus clock speed, extra data transfer cycle, improved bus width and throughput is highly desirable for a low cost, reduced time-to-market and efficient System-on-Chip (SoC). This paper presents a survey of WISHBONE bus architecture and its comparison with three other on-chip bus architectures viz. Advanced Microcontroller Bus Architecture (AMBA) by ARM, CoreConnect by IBM and Avalon by Altera. The WISHBONE Bus Architecture by Silicore Corporation appears to be gaining an upper edge over the other three bus architecture types because of its special performance parameters like the use of flexible arbitration scheme and additional data transfer cycle (Read-Modify-Write cycle). Moreover, its IP Cores are available free for use requiring neither any registration nor any agreement or license. KEYWORDS SoC buses, WISHBONE Bus, WISHBONE Interface 1. INTRODUCTION The introduction and advancement of multimillion-gate chips technology with new levels of integration in the form of the system-on-chip (SoC) design has brought a revolution in the modern electronics industry. With the evolution of shrinking process technologies and increasing design sizes [1], manufacturers are integrating increasing numbers of components on a chip.
    [Show full text]
  • Copyright by Iat Pui Chan Master of Science in Engineering December 2009
    Copyright by Iat Pui Chan Master of Science in Engineering December 2009 The Report Committee for Iat Pui Chan Certifies that this is the approved version of the following report: USB 2.0 ULPI Design APPROVED BY SUPERVISING COMMITTEE: Supervisor: Jacob Abraham Mark McDermott USB2.0 ULPI Design by Iat Pui Chan, BSEE Report Presented to the Faculty of the Graduate School of The University of Texas at Austin in Partial Fulfillment of the Requirements for the Degree of Master of Science in Engineering The University of Texas at Austin December 2009 Abstract USB2.0 ULPI Design Iat Pui Chan, MSE The University of Texas at Austin, Fall 2009 Supervisor: Jacob Abraham This report outlines an implementation of an USB 2.0 ULPI LINK design. Chapter 1 presents an overview of the design and hardware required in the project. Chapter 2 presents how the design functions in an USB system. Chapter 3 describes the hardware implementation. Simulation result and synthesis result are shown in Chapter 4 and 5. iv Table of Contents List of Tables ........................................................................................................ vii List of Figures...................................................................................................... viii List of Figures...................................................................................................... viii Chapter 1: Introduction...........................................................................................1 1.1 System Overview......................................................................................1
    [Show full text]
  • Machxo3d Device Family Data Sheet
    MachXO3D Device Family Data Sheet FPGA-DS-02026-1.0 November 2019 MachXO3D Device Family Data Sheet Disclaimers Lattice makes no warranty, representation, or guarantee regarding the accuracy of information contained in this document or the suitability of its products for any particular purpose. All information herein is provided AS IS and with all faults, and all risk associated with such information is entirely with Buyer. Buyer shall not rely on any data and performance specifications or parameters provided herein. Products sold by Lattice have been subject to limited testing and it is the Buyer's responsibility to independently determine the suitability of any products and to test and verify the same. No Lattice products should be used in conjunction with mission- or safety-critical or any other application in which the failure of Lattice’s product could create a situation where personal injury, death, severe property or environmental damage may occur. The information provided in this document is proprietary to Lattice Semiconductor, and Lattice reserves the right to make any changes to the information in this document or to any products at any time without notice. © 2019 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice. 2 FPGA-DS-02026-1.0 MachXO3D Device Family
    [Show full text]
  • Design and Verification Point-To-Point Architecture of WISHBONE Bus for System-On-Chip
    International Journal of Emerging Engineering Research and Technology Volume 2, Issue 2, May 2014, PP 155-159 Design and Verification Point-to-Point Architecture of WISHBONE Bus for System-on-Chip Chandrala Brijesh A.1, Mahesh T. Kolte2 1Department of electronics and telecommunication, MIT College of Engineering, Pune, India 2Department of electronics and telecommunication, MIT College of Engineering, Pune, India Abstract: SOC design is an integration of multi million transistors in a single chip for time to market and reducing the cost of the design. This paper presents point-to-point Architecture of WISHBONE bus. Main aim of the WISHBONE bus Architectures are to transfer the data from master to slave in different application without redesign of IP core. And that one will increase the productivity with reduction in design time. Standard interface bus protocol should do the plug and play. Keywords: SOC, WISHBONE, Point-to-Point, Shared Bus interconnection, Data Flow interface architecture, Crossbar switch interconnection. 1. INTRODUCTION cores together. With the use of standard interconnection scheme, the cores may be Recent advancement in technology allows integrated more easily and quickly by the end integration of logic functions of multimillion user. This specification may be used for firm transistors into a single chip. To keep pace with core or hard core and soft core IP. Since hard the levels of integration, design engineers have cores and firm are generally conceived as soft developed new methodologies and techniques to cores. manage the increased complexity in these large chips [1]. System-on-Chip (SOC) design is The evolution of shrinking process technologies proposed as an extended methodology to this and increasing design sizes [3][4] has problem where intellectual property (IP) cores of encouraged the manufacturers to undertake and embedded processors, interface blocks, analog do this kind of multiple component integration blocks and memory blocks are combined on a on a single chip.
    [Show full text]
  • Design and Verification of Serial Peripheral Interface Master Core Using Universal Verification Methodology
    International Journal of Computer Sciences and Engineering Open Access Research Paper Vol.-7, Special Issue-14, May 2019 E-ISSN: 2347-2693 Design and Verification of Serial Peripheral Interface Master Core Using Universal Verification Methodology Punith Kumar M B1*, Sreekantesha H N 2 1,2Deparment of ECE, PESCE, Mandya, India Corresponding Author: [email protected] DOI: https://doi.org/10.26438/ijcse/v7si14.711 | Available online at: www.ijcseonline.org Abstract--In today’s world, number of communication protocols for both long and short distance communication purpose, long distance protocols is USB (Universal Serial Bus), ETHERNET, PCI-EXPRESS. SPI (Serial Peripheral interface) and I2C are used for short distance communication protocols. SPI is one of the commonly used bus protocol for connecting peripheral devices to microprocessor .SPI is full duplex, high speed an synchronous bus protocol used for on-board or intra-chip communication In this project the configurable architecture of SPI Protocol with Wishbone Interface has been designed .The main advantage of this design is it overcomes the weaknesses of traditional SPI Bus protocol. As the complexity of the circuit is numerous so there is need of verification methodology to quench the product failure. This project emphasizes on verification of SPI master core verification using Universal Verification Methodology. Keywords—SPI, Wishbone, UVM, SystemVerilog. UVM is a reusable SystemVerilog based on Verification I. INTRODUCTION environment. The development of advanced integrated circuits not only Objective of this work is: increased the complexity of IC design but also IC verification Design Serial Peripheral Interface (SPI) protocol equally challenging. Around 70% spend on verification and using Verilog.
    [Show full text]
  • Wishbone Soc Reference Design for EFM-02
    Wishbone SoC Reference Design for EFM-02 The efm02_soc reference design demonstrates, how to connect FPGA IP cores like peripheral modules and memory to a host PC via the on-board Cypress FX-3 super-speed USB3.0 controller. It uses the CESYS UDK3 that comes with the EFM02 module. It is ideally suited as a starting point for user designs. The host software can read and write all functional blocks of the reference design (i.e. DDR2 SDRAM, Flash memory or General Purpose IO ports), by calling the read and write functions of the API. The referenced addresses are embedded in the UDK3 protocol, transferred serial over the USB (Universal Serial Bus) and converted into Wishbone bus-cycles. This way, the host-software can access registers or memory locations in the FPGA by addressing them. You can easily expand the efm02_soc design by adding your own blocks to the Wishbone bus or modifying existing ones. The reference design comes in VHDL source code. Depending on the target device (SLX45 or SLX150), the Xilinx(tm) ISE Webpack or ISE Design Suite can be used to generate FPGA bitfiles. UG100 (v1.1) April 07, 2014 www.cesys.com 1 Features Features The efm02_soc reference design contains the follwing basic elements: • A clock manager to generate independent clocks for the FX-3 GPIF interface and the Wishbone bus with its peripheral modules. • Wishbone SoC interconnect Architecture, 32 Bit data bus • FX-3 GPIF-II interface, Wishbone busmaster • DDR2 SDRAM interface based on Xilinx(tm) MIG Memory Interface Generator with a Wishbone wrapper.
    [Show full text]
  • WISHBONE System-On-Chip (Soc) Interconnection Architecture for Portable IP Cores
    Specification for the: WISHBONE System-On-Chip (SoC) Interconnection Architecture for Portable IP Cores Revision: B.1 Preliminary Silicore Corporation 6310 Butterworth Lane – Corcoran, MN 55340 TEL: (763) 478-3567 FAX: (763) 478-3568 www.silicore.net Electronic DeDeesignsign Sensors • IP Cores This Page is Intentionally Blank WISHBONE SoC Architecture Specification, Revision B 2 Stewardship Stewardship for this specification is maintained by Silicore Corporation. Questions, comments and suggestions about this document are welcome and should be directed to: Wade D. Peterson, Silicore Corporation 6310 Butterworth Lane – Corcoran, MN 55340 TEL: (763) 478-3567; FAX: (763) 478-3568 E-MAIL: [email protected] URL: www.silicore.net Silicore Corporation maintains this document as a service to its customers and to the IP core in- dustry as a whole. The intent of this specification is to improve the quality of Silicore products, as well as to foster cooperation among the users and suppliers of IP cores. Copyright & Trademark Release / Royalty Release / Patent Notice Notice is hereby given that this document is not copyrighted, and is in the public domain. It may be freely copied and distributed by any means. The term WISHBONE and the WISHBONE compatible logo are not trademark protected. The WISHBONE logo may be freely used under the compatibility conditions stated elsewhere in this document. This specification may be used for the design and production of system-on-chip (SoC) compo- nents without royalty or other financial obligation to Silicore Corporation. The author(s) of this specification are not aware that the information contained herein, nor of products designed to the specification, cause infringement on the patent, copyright, trademark or trade secret rights of others.
    [Show full text]
  • Modular, Configurable Bus Architecture for Ease of IP Reuse on System on Chip and ASIC Devices
    Portland State University PDXScholar Dissertations and Theses Dissertations and Theses 1-1-2010 Modular, Configurable Bus Architecture for Ease of IP Reuse on System on Chip and ASIC Devices Naveendran Balasingam Portland State University Follow this and additional works at: https://pdxscholar.library.pdx.edu/open_access_etds Let us know how access to this document benefits ou.y Recommended Citation Balasingam, Naveendran, "Modular, Configurable Bus Architecture for Ease of IP Reuse on System on Chip and ASIC Devices" (2010). Dissertations and Theses. Paper 163. https://doi.org/10.15760/etd.163 This Thesis is brought to you for free and open access. It has been accepted for inclusion in Dissertations and Theses by an authorized administrator of PDXScholar. Please contact us if we can make this document more accessible: [email protected]. Modular, Configurable Bus Architecture Targeted for Ease of IP Reuse on System on Chip and ASIC Devices by Naveendran Balasingam A thesis submitted in partial fulfillment of the requirements for the degree of Master of Science in Electrical and Computer Engineering Thesis Committee: Xiaoyu Song, Chair Douglas V. Hall Jingke Li Portland State University 2010 i Abstract Integrated Circuit (IC) designs are increasingly moving towards Intellectual Property (IP) reuse for various targeted products and market segments. Therefore, there is a need to share and synergize internal bus architectures to enable the reuse of IP blocks for various ASIC and SoC applications. Due to the different market segments of various ASICs and SoCs, design teams and architects have opted to use customized internal bus architectures to suit the respective targeted features for their market segments.
    [Show full text]
  • Design and Implementation of Wishbone Bus Interface Architecture for Soc Integration USING VHDL on FPGA
    International Journal on Recent and Innovation Trends in Computing and Communication ISSN: 2321-8169 Volume: 2 Issue: 7 1847 – 1850 _______________________________________________________________________________________________ Design and Implementation of Wishbone Bus Interface Architecture for SoC Integration USING VHDL ON FPGA Swati R. Mishra1, Pramod Patil2, Sudhir Shelke3 Research Scholar , Principal, HOD EN/ETC JDCOEM, Nagpur Abstract: Wishbone bus is used to communicate variety of devices. While designing SOC, elastic interfacing between varieties of devices is crucial to get extreme performance. Wishbone bus used to interface a variety of devices due to its open structural design and many a free IP core with a Wishbone interface supplied by Open Cores association. Previously, IP cores used non-standard interconnection schemes that made them difficult to integrate. This required the creation of custom stick logic to interface each of the cores together. By adopting a standard interconnection scheme, the cores can be incorporated more quickly and easily by the end user. This pattern can be used for soft core, firm core or hard core IP. Since firm and hard cores are generally conceived as soft cores, the pattern is written from that standpoint. The WISHBONE interconnect is proposed as a general purpose interface. As such, it defines the standard data exchange between IP core modules. The WISHBONE architects were strongly influenced by three factors. First, there was a need for a good, reliable System-on-Chip integration solution. Second, there was a need for a common interface specification to facilitate structured design methodologies on large project teams. Third, they were impressed by the traditional system integration solutions afforded by microcomputer buses such as PCI bus and VMEbus.
    [Show full text]