DOCSLIB.ORG

Reagent 3 Ammonia Monochloramine Hypochlorite Solution

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Reagent 3 Ammonia Monochloramine Hypochlorite Solution SAFETY DATA SHEET Issue Date 06-Jan-2018 Revision Date 05-Jun-2018 Version 2.3 1. IDENTIFICATION Product identifier Product Name Reagent 3 Ammonia/Monochloramine Hypochlorite Solution Other means of identification Product Code(s) 2776553 Safety data sheet number M01707 Recommended use of the chemical and restrictions on use Recommended Use Determination of free ammonia Uses advised against No information available Details of the supplier of the safety data sheet Initial Supplier Identifier Hach Sales & Service LP. 3020 Gore Road, London, Ontario N5V 4T7 Canada Tel: 1-800-665-7635 Manufacturer Address Hach Company P.O. Box 389 Loveland, CO 80539 USA +1(970) 669-3050 Emergency telephone number Emergency Telephone Chemtrec 1-800-424-9300 CANUTEC 613-992-4624 2. HAZARD IDENTIFICATION Classification Serious eye damage/eye irritation Category 1 Respiratory sensitization Skin sensitization Germ cell mutagenicity Carcinogenicity Reproductive toxicity Label elements Signal word - Danger Hazard statements H318 - Causes serious eye damage _____________________________________________________________________________________________ EN / HGHS Page 1 / 14 2776553 - Reagent 3 Ammonia/Monochloramine Revision Date 05-Jun-2018 Hypochlorite Solution _____________________________________________________________________________________________ Precautionary Statements P280 - Wear protective gloves/protective clothing/eye protection/face protection P305 + P351 + P338 - IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing P310 - Immediately call a POISON CENTER or doctor Unknown Acute Toxicity 0 % of the mixture consists of ingredient(s) of unknown toxicity. 0 % of the mixture consists of ingredient(s) of unknown acute oral toxicity 0 % of the mixture consists of ingredient(s) of unknown acute dermal toxicity 0 % of the mixture consists of ingredient(s) of unknown acute inhalation toxicity (dust/mist) 0 % of the mixture consists of ingredient(s) of unknown acute inhalation toxicity (vapor) 0 % of the mixture consists of ingredient(s) of unknown acute inhalation toxicity (gas) Other Hazards Known Toxic to aquatic life. 3. COMPOSITION/INFORMATION ON INGREDIENTS Substance Not applicable Mixture Chemical name Synonyms CAS No. Percent Range Units HMIRA # Sodium hypochlorite Sodium 7681-52-9 <1% g - hypochlorite Sodium hydroxide Caustic soda 1310-73-2 <0.1% g - Sodium hydroxide 4. FIRST AID MEASURES Description of first aid measures General advice Immediate medical attention is required. Show this safety data sheet to the doctor in attendance. Inhalation Remove to fresh air. Get medical attention immediately if symptoms occur. Eye contact Get immediate medical advice/attention. Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Keep eye wide open while rinsing. Do not rub affected area. Skin contact Wash off immediately with soap and plenty of water for at least 15 minutes. Get medical attention if irritation develops and persists. Ingestion Clean mouth with water and drink afterwards plenty of water. Never give anything by mouth to an unconscious person. Do NOT induce vomiting. Call a physician. _____________________________________________________________________________________________ EN / HGHS Page 2 / 14 2776553 - Reagent 3 Ammonia/Monochloramine Revision Date 05-Jun-2018 Hypochlorite Solution _____________________________________________________________________________________________ Self-protection of the first aider Avoid contact with skin, eyes or clothing. Wear personal protective clothing (see section 8). Most important symptoms and effects, both acute and delayed Symptoms Burning sensation. Indication of any immediate medical attention and special treatment needed Note to physicians Treat symptomatically. 5. FIRE-FIGHTING MEASURES Suitable Extinguishing Media Use extinguishing measures that are appropriate to local circumstances and the surrounding environment. Unsuitable Extinguishing Media Caution: Use of water spray when fighting fire may be inefficient. Specific hazards arising from the No information available. chemical Hazardous combustion products This material will not burn. Special protective equipment for Firefighters should wear self-contained breathing apparatus and full firefighting turnout fire-fighters gear. Use personal protection equipment. 6. ACCIDENTAL RELEASE MEASURES Personal precautions, protective equipment and emergency procedures WHMIS Notice Only persons properly qualified to respond to an emergency involving hazardous substances should respond to a spill involving chemicals. See Section 13, Special Instructions for disposal assistance. Personal precautions Avoid contact with skin, eyes or clothing. Use personal protective equipment as required. Other Information Refer to protective measures listed in Sections 7 and 8. Environmental precautions Environmental precautions Prevent further leakage or spillage if safe to do so. Methods and material for containment and cleaning up Methods for containment Prevent further leakage or spillage if safe to do so. Methods for cleaning up Pick up and transfer to properly labeled containers. Prevention of secondary hazards Clean contaminated objects and areas thoroughly observing environmental regulations. 7. HANDLING AND STORAGE Precautions for safe handling Advice on safe handling Handle in accordance with good industrial hygiene and safety practice. Avoid contact with skin, eyes or clothing. Do not eat, drink or smoke when using this product. Conditions for safe storage, including any incompatibilities _____________________________________________________________________________________________ EN / HGHS Page 3 / 14 2776553 - Reagent 3 Ammonia/Monochloramine Revision Date 05-Jun-2018 Hypochlorite Solution _____________________________________________________________________________________________ Storage Conditions Keep containers tightly closed in a dry, cool and well-ventilated place. Store locked up. Keep out of the reach of children. 8. EXPOSURE CONTROLS/PERSONAL PROTECTION Control parameters Exposure Limits This product, as supplied, does not contain any hazardous materials with occupational exposure limits established by the region specific regulatory bodies Chemical name Alberta OEL British Columbia Manitoba OEL New Brunswick New Foundland & OEL OEL Labrador OEL Sodium hydroxide Ceiling: 2 mg/m3 Ceiling: 2 mg/m3 Ceiling: 2 mg/m3 Ceiling: 2 mg/m3 Ceiling: 2 mg/m3 <0.1% Chemical name Northwest Nova Scotia OEL Nunavut OEL Ontario TWA Prince Edward Territories OEL Island OEL Sodium hydroxide Ceiling: 2 mg/m3 Ceiling: 2 mg/m3 Ceiling: 2 mg/m3 Ceiling: 2 mg/m3 Ceiling: 2 mg/m3 <0.1% Chemical name Quebec OEL Saskatchewan OEL Yukon OEL Sodium hydroxide Ceiling: 2 mg/m3 Ceiling: 2 mg/m3 Ceiling: 2 mg/m3 <0.1% Chemical name ACGIH TLV OSHA PEL NIOSH IDLH Sodium hydroxide Ceiling: 2 mg/m3 TWA: 2 mg/m3 IDLH: 10 mg/m3 <0.1% (vacated) Ceiling: 2 mg/m3 Ceiling: 2 mg/m3 Legend See section 16 for terms and abbreviations Appropriate engineering controls Engineering Controls Showers Eyewash stations Ventilation systems. Individual protection measures, such as personal protective equipment Respiratory protection No protective equipment is needed under normal use conditions. If exposure limits are exceeded or irritation is experienced, ventilation and evacuation may be required. Hand Protection Wear suitable gloves. Eye/face protection Tight sealing safety goggles. Skin and body protection Wear suitable protective clothing. General Hygiene Considerations Avoid contact with skin, eyes or clothing. Wear suitable gloves and eye/face protection. Do not eat, drink or smoke when using this product. Environmental exposure controls Local authorities should be advised if significant spillages cannot be contained. Do not allow into any sewer, on the ground or into any body of water. Thermal hazards None under normal processing. 9. PHYSICAL AND CHEMICAL PROPERTIES _____________________________________________________________________________________________ EN / HGHS Page 4 / 14 2776553 - Reagent 3 Ammonia/Monochloramine Revision Date 05-Jun-2018 Hypochlorite Solution _____________________________________________________________________________________________ Information on basic physical and chemical properties Physical state Liquid Appearance aqueous solution Color colorless clear Odor Odorless Odor threshold No data available Property Values Remarks • Method Molecular weight No data available pH 12.7 Melting point/freezing point ~ 0 °C / 32 °F Estimation based on theoretical calculation Boiling point / boiling range ~ 100 °C / 212 °F Estimation based on theoretical calculation Evaporation rate 1 (water = 1) Estimation based on theoretical calculation Vapor pressure 23.702 mm Hg / 3.16 kPa at 25 °C / 77 °F Estimation based on theoretical calculation Vapor density (air = 1) 0.62 (air = 1) Specific gravity (water = 1 / air = 1) 1.0200 Partition Coefficient (n-octanol/water) Not applicable Soil Organic Carbon-Water Partition Not applicable Coefficient Autoignition temperature No data available Decomposition temperature No data available Dynamic viscosity No data available Kinematic viscosity No data available Solubility(ies) Water solubility Water solubility classification Water solubility Water Solubility Temperature Soluble > 1000 mg/L 25 °C / 77 °F Solubility in other solvents Chemical Name Solubility classification
Load more

Recommended publications
  • Qualitative and Quantitative Tier 3 Assessment
    Consider It Done www.ehs-support.com.au Qualitative and Quantitative Tier 3 Assessment Sodium Hypochlorite In accordance with the Chemical Risk Assessment Framework (CRAF), the assessment for this Tier 3 chemical includes the following components: completing the screening; developing a risk assessment dossier and Predicted No-Effects Concentrations (PNECs) for water and soil; and, completing a qualitative and quantitative assessment of risk. Each of these components is detailed within this attachment. Background Sodium hypochlorite is a component in a Water Management Facility (WMF) product (Sodium Hypochlorite Solution 12.5%) used as an oxidising agent/disinfectant during oily water treatment. A safety data sheet (SDS) for the WMF product is included as Attachment 1. Process and usage information for this chemical is included in Attachment 2 and summarised in Table 1. Table 1 Water Management Facility Chemicals – Tier 3 Chemicals Approximate Quantity Stored On- Proprietary Name Chemical Name CAS No. Use Site (plant available storage) Sodium Sodium Hypochlorite 7681-52-9 Oxidising 15000 L Hypochlorite Sodium Hydroxide 1310-73-2 agent/disinfectant Solution 12.5% CAS No = Chemical Abstracts Service Number L = litre The assessment of toxicity of this chemical was used to evaluate human health exposure scenarios and is presented in Attachment 3. Since an Australian Drinking Water Guideline (ADWG) Value is available (see Table 2), toxicological reference values (TRVs) were not derived for the chemical. A detailed discussion of the drinking
    [Show full text]
  • Reducing Trihalomethane Concentrations by Using Chloramines As a Disinfectant
    REDUCING TRIHALOMETHANE CONCENTRATIONS BY USING CHLORAMINES AS A DISINFECTANT by Elizabeth Anne Farren A Thesis Submitted to the Faculty of the WORCESTER POLYTECHNIC INSTITUTE in partial fulfillment of the requirements for the Degree of Master of Science in Environmental Engineering by ___________________________________ April 2003 APPROVED: ___________________________________ Dr. Jeanine D. Plummer, Major Advisor ____________________________________ Dr. Frederick L. Hart, Head of Department Abstract Disinfectants such as chlorine are used in drinking water treatment to protect the public health from pathogenic microorganisms. However, disinfectants also react with humic material present in raw water sources and produce by-products, such as trihalomethanes. Total trihalomethanes (TTHMs) include four compounds: chloroform, bromodichloromethane, dibromochloromethane and bromoform. TTHMs are carcinogenic and have been found to cause adverse pregnancy outcomes. Therefore, the United States Environmental Protection Agency (U.S. EPA) has set the maximum contaminant limit for TTHMs at 80 µg/L. Additional regulations require reliable drinking water disinfection for resistant pathogens and treatment plants must simultaneously control TTHMs and achieve proper disinfection. Research has shown that THM formation depends on several factors. THM concentrations increase with increasing residence time, increased temperature and increased pH. The disinfectant type and concentration is also significant: THM concentrations can be minimized by using lower disinfectant doses or alternative disinfectants to chlorine such as chloramines. Chloramines are formed by the addition of both chlorine and ammonia. The Worcester Water Filtration Plant in Holden, MA currently uses both ozone and chlorine for primary disinfection. Chlorine is also used for secondary disinfection. This study analyzed the effect of using chloramines versus free chlorine on TTHM production at the plant.
    [Show full text]
  • Survey of Sodium and Calcium Hypochlorite
    Survey of sodium and calcium hypochlorite Part of the LOUS review Environmental project No. 1720, 2015 Title: Author: Survey of sodium and calcium hypochlorite Carlos Escudero-Oñate Norwegian Institute for Water Research (NIVA) Published by: The Danish Environmental Protection Agency Strandgade 29 DK-1401 Copenhagen K Denmark www.mst.dk Year: ISBN no. 2015 978-87-93352-33-9 Disclaimer: When the occasion arises, the Danish Environmental Protection Agency will publish reports and papers concerning research and development projects within the environmental sector, financed by study grants provided by the Danish Environmental Protection Agency. It should be noted that such publications do not necessarily reflect the position or opinion of the Danish Environmental Protection Agency. However, publication does indicate that, in the opinion of the Danish Environmental Protection Agency, the content represents an important contribution to the debate surrounding Danish environmental policy. May be quoted provided the source is acknowledged. 2 Survey of sodium and calcium hypochlorite Contents Preface ...................................................................................................................... 5 Conclusion and Summary .......................................................................................... 7 Sammenfatning og konklusion ................................................................................. 11 Conclusion ..............................................................................................................
    [Show full text]
  • Monochloramine in Drinking-Water
    WHO/SDE/WSH/03.04/83 English only Monochloramine in Drinking-water Background document for development of WHO Guidelines for Drinking-water Quality © World Health Organization 2004 Requests for permission to reproduce or translate WHO publications - whether for sale of for non- commercial distribution - should be addressed to Publications (Fax: +41 22 791 4806; e-mail: [email protected]. The designations employed and the presentation of the material in this publication do not imply the expression of any opinion whatsoever on the part of the World Health Organization concerning the legal status of any country, territory, city or area or of its authorities, or concerning the delimitation of its frontiers or boundaries. The mention of specific companies or of certain manufacturers' products does not imply that they are endorsed or recommended by the World Health Organization in preference to others of a similar nature that are not mentioned. Errors and omissions excepted, the names of proprietary products are distinguished by initial capital letters. The World Health Organization does not warrant that the information contained in this publication is complete and correct and shall not be liable for any damage incurred as a results of its use. Preface One of the primary goals of WHO and its member states is that “all people, whatever their stage of development and their social and economic conditions, have the right to have access to an adequate supply of safe drinking water.” A major WHO function to achieve such goals is the responsibility “to propose ... regulations, and to make recommendations with respect to international health matters ....” The first WHO document dealing specifically with public drinking-water quality was published in 1958 as International Standards for Drinking-water.
    [Show full text]
  • Method 127: Determination of Monochloramine Concentration in Drinking Water Questions Concerning This Document Should Be Addressed To
    Method 127: Determination of Monochloramine Concentration in Drinking Water Questions concerning this document should be addressed to: Matthew T. Alexander, P.E. U.S. EPA, Office of Ground Water and Drinking Water, Standards and Risk Management Division, Technical Support Center, 26 W. Martin Luther King Dr. Cincinnati, OH 45268 Phone: (513) 569-7380 [email protected] Office of Water (MS-140) EPA 815-B-21-004 January 2021 Version 1.0 Authors Matthew T. Alexander, P.E., U.S. EPA (Cincinnati, OH) Thomas E. Waters, P.E., U.S. EPA (Cincinnati, OH) David G. Wahman, PhD, P.E., U.S. EPA (Cincinnati, OH) Glynda A. Smith, PhD, U.S. EPA (Cincinnati, OH) Acknowledgements The following people are acknowledged for their support in development and/or validation of this method: William A. Adams, PhD, Alison Dugan, Christopher Frebis, and Steven C. Wendelken, PhD, U.S. EPA (Cincinnati, OH) Lili Wang and Richard Weisman, U.S. EPA (Washington, DC) Taylor Rosenhagen and Chris Bobay, Louisville Water Company (Louisville, KY) John Consolvo, Joseph Mockus, Alexandra Rosario-Arocho, and, Philadelphia Water Department (Philadelphia, PA) Julian Fairey, PhD, University of Arkansas (Fayetteville, AR) City of Hamilton Water (Hamilton, OH) Greater Cincinnati Water Works (Cincinnati, OH) Augusta Regional Water Treatment Plant (Augusta, KY) City of Falmouth Water and Wastewater Department (Falmouth, KY) Justin Blashaw and Paul Handke, Pennsylvania DEP (New Stanton, PA) Kayla Quinter, former U.S. EPA intern, for development of free chlorine and monochloramine stock solution preparation and standardization procedures. ii Disclaimer Publication of the method, in and of itself, does not establish a requirement, although the use of this method may be specified by the EPA or a state through independent actions.
    [Show full text]
  • Chloramination Recommendations for Public Water Systems That Chloraminate
    Chloramination Recommendations For Public Water Systems that Chloraminate PURPOSE: The Ten State Standards interim standard on chloramination states: “Operating authorities who wish to modify disinfectant practices by using chloramine must show the reviewing authority clear evidence that bacteriological and chemical protection of consumers will not be compromised in any way …” I. Recommendations for Systems that Chloraminate. Monochloramine and free ammonia levels should be tested periodically to ensure that the targets of chloramination are being met. The current ammonia level in the source water of both surface and groundwater systems will affect the amount of chlorine and ammonia required to achieve the desired chlorine to ammonia ratio. Inadequate ammonia feed rates can result in taste and odor problems within the distribution system, while higher free ammonia levels within the distribution system can result in creating nitrite levels high enough to exceed the maximum contaminant level, placing small infants at risk. A. The plant should develop and submit to the District Office for review and approval an operational plan specific to chloramination. At a minimum, the plan needs to address the following items: 1. The water system’s targets with respect to chloramination including, but not limited to, the following: a) The facility’s target chlorine to ammonia ratio needs to be established. To avoid breakpoint reactions, utilities generally strive to maintain the Cl 2:NH 3 ratio in the 1 range of 2.5:1 to 4.1:1 (NH 3 as ammonia) or 4.5:1 to 5:1 (NH 3 as nitrogen) . b) A free ammonia level (NH 3-N) target of 0.01 – 0.04 mg/L, measured at the entrance to the distribution system, is recommended 1.
    [Show full text]
  • EPA Method 551.1: Determination of Chlorination Disinfection
    METHOD 551.1 DETERMINATION OF CHLORINATION DISINFECTION BYPRODUCTS, CHLORINATED SOLVENTS, AND HALOGENATED PESTICIDES/HERBICIDES IN DRINKING WATER BY LIQUID-LIQUID EXTRACTION AND GAS CHROMATOGRAPHY WITH ELECTRON-CAPTURE DETECTION Revision 1.0 J.W. Hodgeson, A.L. Cohen - Method 551, (1990) D.J. Munch (USEPA, Office of Water) and D.P. Hautman (International Consultants, Inc.) - Method 551.1, (1995) NATIONAL EXPOSURE RESEARCH LABORATORY OFFICE OF RESEARCH AND DEVELOPMENT U.S. ENVIRONMENTAL PROTECTION AGENCY CINCINNATI, OHIO 45268 551.1-1 METHOD 551.1 DETERMINATION OF CHLORINATION DISINFECTION BYPRODUCTS, CHLORINATED SOLVENTS, AND HALOGENATED PESTICIDES/HERBICIDES IN DRINKING WATER BY LIQUID-LIQUID EXTRACTION AND GAS CHROMATOGRAPHY WITH ELECTRON-CAPTURE DETECTION 1.0 SCOPE AND APPLICATION 1.1 This method1-9 is applicable to the determination of the following analytes in finished drinking water, drinking water during intermediate stages of treatment, and raw source water. The particular choice of analytes from this list should be a function of the specific project requirements. Analyte CAS No. Disinfection Byproducts (DBPs): Trihalomethanes Chloroform 67-66-3 Bromodichloromethane 75-27-4 Bromoform 75-25-2 Dibromochloromethane 124-48-1 Haloacetonitriles Bromochloroacetonitrile 83463-62-1 Dibromoacetonitrile 3252-43-5 Dichloroacetonitrile 3018-12-0 Trichloroacetonitrile 545-06-2 Other DBPs Chloral Hydrate 75-87-6 Chloropicrin 76-06-2 1,1-Dichloro-2-propanone 513-88-2 1,1,1-Trichloro-2-propanone 918-00-3 Chlorinated Solvents: Carbon Tetrachloride 56-23-5 1,2-Dibromo-3-chloropropane [DBCP] 96-12-8 1,2-Dibromoethane [EDB] 106-93-4 Tetrachloroethylene 127-18-4 1,1,1-Trichloroethane 71-55-6 1,1,2-Trichloroethane 79-00-5 Trichloroethylene 79-01-6 1,2,3-Trichloropropane 96-18-4 Pesticides/Herbicides: Alachlor 15972-60-8 Atrazine 1912-24-9 Bromacil 314-40-9 Cyanazine 21725-46-2 Endrin 72-20-8 551.1-2 Analyte CAS No.
    [Show full text]
  • Guidelines for Drinking-Water Quality, Fourth Edition
    GUIDELINES FOR DRINKING-WATER QUALITY TDI 1.4 µg/kg body weight, based on a NOAEL of 1 mg/kg body weight per day for hepatotoxic effects in a 12-week oral gavage study in rats, adjusting for daily dosing and applying an uncertainty factor of 500 (100 for interspecies and intraspecies variation, 10 for the duration of the study and a modifying factor of 0.5 because it was a bolus study) Limit of detection 0.1–0.3 µg/l by GC-ECD or GC-MS Treatment performance 0.001 mg/l should be achievable using air stripping Guideline value derivation • allocation to water 10% of TDI • weight 60 kg adult • consumption 2 litres/day Additional comments The guideline value is lower than the range of values associated with upper-bound lifetime excess cancer risks of 10−4, 10−5 and 10−6 calculated by linear extrapolation. Assessment date 2003 Principal references IPCS (1999) Carbon tetrachloride WHO (2003) Carbon tetrachloride in drinking-water The primary targets for carbon tetrachloride toxicity are liver and kidney. In ex- periments with mice and rats, carbon tetrachloride proved to be capable of inducing hepatomas and hepatocellular carcinomas. The doses inducing hepatic tumours were higher than those inducing cell toxicity. It is likely that the carcinogenicity of carbon tetrachloride is secondary to its hepatotoxic effects. On the basis of available data, car- bon tetrachloride can be considered to be a non-genotoxic compound. Carbon tetra- chloride is classified by IARC as being possibly carcinogenic to humans (Group 2B): there is sufficient evidence that carbon tetrachloride is carcinogenic in laboratory a nimals, but inadequate evidence in humans.
    [Show full text]
  • CHLORAMINE 1. Exposure Data
    pp295-316.qxd 11/10/2004 11:06 Page 295 CHLORAMINE 1. Exposure Data 1.1 Chemical and physical data 1.1.1 Nomenclature Chem. Abstr. Serv. Reg. No.: 10599-90-3 Chem. Abstr. Name: Chloramide IUPAC Systematic Name: Chloramide Synonyms: Chloroamine; monochloramine; monochloroamine; monochloroammonia 1.1.2 Structural and molecular formulae and relative molecular mass H Cl N H ClH2N Relative molecular mass: 51.47 1.1.3 Chemical and physical properties of the pure substance (Ura & Sakata, 1986) (a) Description: Colourless liquid with a strong pungent odour (b) Melting-point: –66 °C (c) Stability: Stable in aqueous solution, but unstable and explosive in pure form 1.1.4 Technical products and impurities Monochloramine is not known to be a commercial product but is generated in situ as needed. 1.1.5 Analysis Chloramines have been determined in water by amperometric titration. Free chlorine is titrated at a pH of 6.5–7.5, a range at which chloramines react slowly. Chloramines are then –295– pp295-316.qxd 11/10/2004 11:06 Page 296 296 IARC MONOGRAPHS VOLUME 84 titrated in the presence of the correct amount of potassium iodide in the pH range 3.5–4.5. The tendency of monochloramine to react more readily with iodide than dichloramine provides a means for estimation of monochloramine content (American Public Health Asso- ciation/American Water Works Association/Water Environment Federation, 1999). In another method, N,N-diethyl-para-phenylenediamine is used as an indicator in the titrimetric procedure with ferrous ammonium sulfate. In the absence of an iodide ion, free chlorine reacts instantly with the N,N-diethyl-para-phenylenediamine indicator to produce a red colour.
    [Show full text]
  • Science & Myth Busting
    Science & Myth Busting Associate Director & Adjunct Professor Environmental Health Concordia University College of Alberta Chloramine was been in used in North America for nearly 100 years (Denver 1917) The use has increased in the last decade because of concerns with THM formation from chlorination Regionalization also resulted in a need for chloramine to maintain longer residual within the distribution system Chlorine: Vancouver, Calgary, Montreal, Regina, Winnipeg, Saskatoon Ultraviolet: Edmonton, Vancouver, Winnipeg Chloramine: Edmonton, Ottawa, Toronto, Waterloo. BC: Abbotsford, Mission, Victoria Ozone: Montreal, Winnipeg, Vancouver Advantages: -Longer residual time -Less regulated DBP (THM and HAA) formation -More effective against Legionella in water -More effective against biofilm Disadvantages: -Less effective disinfectant -NDMA as DBP -Increase lead leaching from pipes -Nitrification in distribution system -Result in haemolytic anaemia and methaemoglobinaemia in renal dialysis patients A presentation addressing technical issues based on the recent public protests across North America against the use of chloramine in drinking water Chloramine and the Environment “Bad for Fish, Good for People?” …chloramine exists as three different forms or species: monochloramine (NH2Cl), dichloramine (NHCl2) and trichloramine (NCl3). They are chemically related and are easily converted into each other; thus, they are more appropriately called chloramines. The three species of chloramine constantly and rapidly shift from one form to another… …Even time plays a factor because after a day or so, with no changes in conditions, monochloramine in a water system will slowly degrade to form dichloramine and some trichloramine. In contrast to what water utilities claim, it is impossible to have only monochloramine. It is not unusual in water systems for harmful di and trichloramines to occur… Water utilities use a form of chloramine that is composed of one part chlorine, to one part ammonia.
    [Show full text]
  • Chlorination and Chloramination
    Science of Chloramination Maine Water Utilities Association Michael Koza, Portland Water District June 2010 Chloramination The process of combining chlorine and ammonia to create a “combined” form of chlorine for drinking water disinfection Maine Water Utilities Association Combined Compounds Chloramine is a general term that describes three related compounds: MONOchloramine, NH2Cl DIchloramine, NHCl2 TRIchloramine, NCl3 Monochloramine is preferred for drinking water disinfection. Maine Water Utilities Association Chloramine structure The molecular structure MonochloramineTrichloramineDichloramine of all three chloramine compounds resembles ammonia, NH3 A chlorine atom will replace one, two, and three hydrogen atoms respectively for the formation of mono-, di-, and trichloramines. Maine Water Utilities Association Why Chloraminate? Provide Longer Lasting Residual – Driving factor for PWD in 1939 Reduce DBP Formation – To meet lower MCL’s of Stage 1 D/DBP Rule Reduce T & O – if applicable Maine Water Utilities Association Chloramine History Successful usage in 1920-30’s (16%) Decreased in popularity in 1940-50’s - scarcity of ammonia - World War II (2.6%) SDWA in 1974 and 1986. THM regs (23%) More stringent D/DBP Rules pushing % up ~30% Utility Considerations For a drinking water utility, chloramination may or may not be a good alternative to free chlorination. What is the source water type and quality and the overall treatment process required to produce potable drinking water. Even with the full range of chloramine benefits, consideration must be given to secondary impacts associated with chloramination – primarily the potential for nitrification within the distribution system. Maine Water Utilities Association Considerations (cont.) With chloramination, an additional chemical must be purchased, stored, and applied to the process.
    [Show full text]
  • The Role and Behavior of Chloramines in Drinking Water
    The Role and Behavior of Chloramines in Drinking Water May 2019 Djanette Khiari, The Water Research Foundation LAST UPDATED: MAY 2019 CHLORAMINATION HAS BEEN USED funded more than 70 research projects they play in water quality improvements in drinking water treatment since the on the optimization of chloramination for drinking water utilities. Using doc- early 1900s, but its use has been low while considering chloramine-related umented information from 68 utilities compared to that of chlorine. In recent issues, such as key factors to consider that use chloramines, the report identi- years, many utilities implemented chlo- when making the switch to chlora- fies critical parameters for controlling ramine, primarily to comply with the mines, prevention and mitigation of chloramination and spells out a chlora- U.S. Environmental Protection Agency’s nitrification events, minimization of mination optimization strategy. (EPA) Stage 1 and Stage 2 Disinfectants disinfection by-products, and lead and A Guide for the Implementation and and Disinfection Byproducts Rules copper release related to chloramine Use of Chloramines (2847) summa- (D/DBPR). Chloramines are less reac- use. What follows is a summary of rizes the current state of knowledge tive than chlorine and produce lower the relevant chloramine- related WRF regarding chloramine use and synthe- concentrations of trihalomethanes reports. For an overview of chlora- sizes the information into step-by- step (THMs) and haloacetic acids (HAAs). mine use in water treatment and a procedures for using chloramines in a In drinking water treatment, chlora- discussion of the concerns associ- water system. mines are primarily used as a secondary ated with chloramine use, refer to the Finally, Long- Term Effects of disinfectant to provide a residual in the archived WRF webcast, “Talking About Disinfection Changes on Water Quality distribution system.
    [Show full text]