DOCSLIB.ORG

Caulk Guns Caulk Guns Chalk/Plumb Lines & Chalk Fence Layout Tools

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Caulk Guns Caulk Guns Chalk/Plumb Lines & Chalk Fence Layout Tools Caulk Guns Caulk Guns MANUAL AIR MW-41001 10.0 fl.oz. / 7:1 Wexford® Steel Caulk Gun Use for low to medium viscosity materials. Wear compensat- ing device. Retractable seal puncturing device. Metal with MW-41001 epoxy finish. Hex drive rod. Built-in ladder hook. Steel catch CCESSORIES plate. Made in UK. MW-61001 10.0 fl.oz. / 100PSI Tyne Air® Aluminum Air Caulk Gun MW-61002 20.0 fl.oz. / 100PSI Jumbo Air® Aluminum Air Caulk Gun Air action on cartridge plunger. Aluminum barrel. Adjustable air & A MW-21001 10.0 fl.oz. / 7:1 Wexford II® Nylon Fiberglass Caulk Gun regulator – 100 PSI maximum. Instant dump valve. Silencer. Use for low to medium viscosity materials. Retractable seal Quick release end cap. Rotating air hose connector included. puncturing device. Corrosion resistant. Hex drive rod. Built-in ladder hook. Steel catch plate. Automatic dripless feature. Made in England. OOLS MW-21001 T Made in UK. MW-61001 MW-41004 10.0 fl.oz. / 12:1 Chilton® Steel Caulk Gun Use for medium to high viscosity. Rotating barrel for iliary corners. Wear compensating device. Patented sintered X MW-41004 steel catch plate. Built-in ladder hook. High volume U usage. Thumb activated instant pressure release. Chalk/Plumb Lines & Chalk A Made in USA. CHALK/PLUMB LINES MW-RCL100 100” Chalk/Plumb Line Die cast reel type with enamel finish. ® MW-41004XT 10.0 fl.oz. / 18:1 Chilton Steel Caulk Gun Slide action lock and hook ring also provides Extra thrust. Use for high viscosity materials. Wear compensating device. Built-in ladder hook. Patented sintered plumb bob action. Lock releases automatically MW-41004XT steel catch plate. Barrel turns for corners. Medium- high on rewind. Handle closes flush with case. viscosity materials. Thumb activated instant pressure release. Leak resistant tip. (Chalk not included) Made in USA. Made in Dominican Republic. MW-410042T 1.0 qt. / 26:1 Ascot® Steel Caulk Gun MW-FRCB100 100’ Fast Reel Chalk/Plumb Line Maximum power ratio. Use for high viscosity materials. MW-RCL100 MW-FRCB100 Rewinds 3-1/2 times faster. High impact Wear compensating device. Support straps. Secure plastic case. Push button line release. Locking MW-410042T cartridge fit. Built-in ladder hook. Case hardened cast handle allows for use as plumb bob. (Chalk steel plate. Thumb activated instant pressure release. CHALK REFILLS not included.) Made in Dominican Republic. Made in England. ® MW-41002 1.0 qt. / 20:1 Jumbo Quart Steel Caulk Gun MW-R8B 8 oz.(227g) Blue Chalk High capacity. Use for medium to high viscosity materials. MW-R8R 8 oz.(227g) Red Chalk Wear compensating device. Support straps. Secure Special formula for hard clean lines in easy cartridge fit. Built-in ladder hook. Case hardened cast MW-41002 steel plate. Thumb activated instant pressure release. to use plastic squeeze bottle. Made in USA. Made in USA. MW-R8B MW-R8R MW-51000 10.0 fl.oz. / 12:1 Avon® Aluminum Caulk Gun Use for medium to high viscosity materials. Pre-configured for sausage application with plunger included for cartridge application. Patented wear compensating device. Drawn MW-51000 aluminum barrel. Quick release end cap. Includes: Fence Layout Tools 2 orange cone nozzles, spare sausage plunger, ladder hood, and spanner wrench. Made in UK. STEEL MARKING CABLES MW-SMC250 250’(76.25m) Steel Marking Cable MW-SMC500 500’(152.5m) Steel Marking Cable MW-51001 20.0 fl.oz. / 12:1 Avon® Aluminum Caulk Gun 1/8”(3.2mm) diameter steel cable on shatter and Use for medium to high viscosity materials. Pre-configured temperature resistant thermoplastic reel. Hand slide for sausage application with plungers included for cartridge mechanism and swivel handle re-winds marking and bulk (G2) applications. Patented wear compensating cable quickly and easily. Cables marked for device. Drawn aluminum barrel. Quick release end cap. 5”(127.0mm) post width on 8’(2.4m) centers. MW-51001 Includes: 3 yellow cone nozzles, ladder hook, spanner Assembled in USA. wrench. Made in UK. MW-SMC250 CABLE CLAMP MW-51002 34 fl.oz. / 12:1 Portland® Aluminum Caulk Gun MW-CBCLMP Cable Clamp Use for medium to high viscosity materials. 34 floz. (966.01ml) Cast malleable iron with 1000 lb. pull capacity up to bulk application. Leather plunger assembly. Patented wear compensating device. Drawn aluminum barrel. Quarter turn 5/16”(8.0mm) diameter cable. Cam action ensures tight MW-51002 steel end cap. Includes: 3 yellow cone nozzles, spanner lock. Spring-loaded with large eyehole for quick connect wrench. Made in UK. to com-a-long. Zinc plating resists rust. Made in Taiwan. MW-CBCLMP 77 78 G-Clamps Measuring Tools OPEN REEL TAPES MW-R100-OR 100’ Open Reel Tape MW-R200-OR 200’ Open Reel Tape MW-71004P 4” G-Clamp ½” (12.7mm) tape width in one-eighth inch measuring units. Tough CCESSORIES MW-71006P 6” G-Clamp ABS plastic case with contoured rubber grip handle and folding end 3”(76.2mm) throat depth and 550 lbs clamp hook for secure anchoring. Nylon coated steel clad tape prevents MW-71004P strength. Works efficiently with one hand. stretching. Made in China. & A Made of projection-welded pressed steel. MW-R200-OR Nylon jaw pads. Swivel base. 7:1 mechanical CLOSED REEL TAPES advantage. Thumb activated instant pressure MWR100P 100’ Closed Reel Tape OOLS release. Made in UK. 3/8”(9.5mm) tape width in one-eighth inch measuring units. Closed T reel hand-wind in tough ABS plastic case. Thick steel blade with epoxy polycoat. Meets or exceeds GSA specifications. Made in USA. MW-71006P iliary MW-R100P X MW- RC125 25’ Retracting Tape RETRACTING TAPES U 1”(25.4mm) tape width in one-sixteenth inch measuring units. A Knife & Knife Blades Impact resistant chrome case. Yellow blade with baked on coating. RETRACTABLE KNIFE MW-RO1 Retractable Knife Three rivet end hook. Positive lock. Oversized numbers. Meets or Heavy-duty die cast handle with comfortable grip. exceeds GSA specifications. Made in USA. Design prevents blade from pushing up through handle under extreme pressure. Spring-loaded MW-RC130 30” Retracting Tape thumb switch adjusts blades to four cutting 1”(25.4mm) tape width in one-eighth inch measuring units. MW-RC125 MW-RC130 MW-R01 positions and retracts for safe locking. Includes Ergonomic rubber grip case. Active bumper. Heavy duty spring. three blades. Made in USA. Yellow blade. Oversized numbers. Assembled in USA. STANDARD BLADES MW-2SB5 5 Pack Standard Utility Blades MICROMETER MW-2SB50 50 Pack Standard Utility Blades MW-RMIC Outside Micrometer Heavy-duty. 0.025”(0.63mm) thick steel. 0 to 1” range in 0.0001” graduations. Carbide face anvils. Ratchet stop. Satin chrome finish. Made in China. MW-2SB5 Made in USA. MW-2SQH5 5 Pack Hook (Square Hole) Blades HOOK BLADES MW-RMIC MW-2SQH100 100 Pack Hook (Square Hole) Blades Heavy-duty .025”(0.635mm) thick steel. Made in USA. Nail Pullers/Pry Bars MW-2SQH5 PRY BARS MW-B221 21”(533.4mm) Superbar® Forged, heat-treated, and spring tempered. “Shepherd’s crook” rocker head is sharp Level MW-B221 with tapered blade and beveled nail slot. MW-AM9 9” Magnetic Torpedo Level Made in USA. Three vials – level, plumb, 45-degree. Magnetic torpedo level with V-grooved top edge. One-piece MW-B215 15”(381.0mm) Superbar® cast aluminum frame. Strong magnetic base. Top Forged, heat-treated, and spring tempered. “Shepherd’s crook” rocker head is sharp MW-AM9 read window. Made in Dominican Republic. MW-B215 with tapered blade and beveled nail slot. Made in USA. MW-B222 5-1/2” Mini-Bar® Tempered steel. Plated finish. Ideal for MW-B222 removing small nails from finish work or trim Magnet and for delicate pry movement. Made in USA. MW-REZMAG Pick-Up Magnet NAIL PULLERS MW-NP12G 11-1/2” Nail Puller Scrap and fastener pick-up magnet. Ceramic magnet Forged, hardened, and tempered for strength with 14 lbs.(6.4kg.) lifting power housed in ABS plastic and long life. Designed for extracting deeply MW-REZMAG base mounted on 24”(609.6mm) steel hand. Trigger imbedded nails. Blue painted finish with plastic release. Weighs 2.0 lb.(0.9kg). Made in USA. MW-NP12G grip to comfort user’s hand. Made in USA. 79 80 Pneumatic Tool Holders Saw Blades Circular – metal DEVIL® MW-ATH14 1/4” NPT Pneumatic Tool Holder MW-ATH38 3/8” NPT Pneumatic Tool Holder Hooks on to belt loop for holster carrying of 1/4” MW-100397 7” Metal Cutting Blade and 3/8” NPT fitting pneumatic air tools. Holds 68 tooth titanium carbide tipped fits 5/8” arbor. CCESSORIES tool by fitting. Made from light-weight aluminum. Cuts sheet steel, siding panels, metal roofing, MW-ATH14, MW-ATH38 Made in USA. etc. Maximum RPM 5800. Made in USA. & A MW-100397 OOLS T Roller Stand Circular – WOOD / VINYL MW-26370 7” Wood/Vinyl Blade MW-GS Adjustable Roller Stand 150 tooth standard steel blade features a Heavy-duty ¾”(19.1mm) black steel pipe legs with super-sharp edge for smooth, clean cuts in up iliary cast aluminum hub and durable 8”(203.2mm) wide X to ¾” plywood, veneer, and vinyl. Made in USA UHMW material roller. Fully adjustable roller height from U 34”(863.6mm) to 52”(1320.8mm) and adjustable third leg A for uneven ground. Collapsible design for easy storage and fast set-up. Locking mechanism with quick release and MW-26370 three lockout plates secure legs in open position. Weighs 17.0 lbs.(7.7kg). Made in USA. MW-GS Striking Tools RIP/CLAW HAMMERS MW-FS99 16 oz. Rip/Claw Hammer Roofing Rollers MW-FS999 20 oz.
Load more

Recommended publications
  • BUGLER SALES CORP. Phone: 516 223-3868 • Fax: 516 868-6998 • E-Mail: [email protected] 969 CHURCH STREET • BALDWIN, NY 11510 PAGE BUGLER SALES CORP
    2005 BUGLER SALES CORP. Phone: 516 223-3868 • Fax: 516 868-6998 • E-Mail: [email protected] 969 CHURCH STREET • BALDWIN, NY 11510 PAGE BUGLER SALES CORP. 2 Phone: 516 223-3868 • Fax: 516 868-6998 969 CHURCH STREET • BALDWIN, NY 11510 LISTING BY MANUFACTURER • AEARO • CELLO • GT WATER PRODUCTS PAGE 48 PAGE 61 PAGE 44 • ALL CRAFTS • CHANNELLOCK TOOLS • GENERAL TOOLS PAGE 57 PAGE 119 PAGE 133 • ALLWAY TOOLS • COLCO HVAC • GENERAL WIRE PAGE 111 FURNACE CEMENT PAGEW 45, 133 • AMERICAN SAW PAGE 77 • GILMOUR PAGE 140-145 • COLEMAN CABLE PAGE 64 • AMERICAN STONE MIX DROPLIGHTS/ • GLOWMASTER PAGES 44, 58, 60, 61 EXTENSIONS PAGE 133 • AMES PAGE 47 • GOJO PAGES 119 • CRESCENT PAGE 61 • ANSELL EDMONT PAGES 39, 137 • GREAT NECK PAGES 57 • DAP PAGES 109/113/121/129 • ARROW PAGES 32/33/54/55/59/109 135-139 PAGE 123 • DASCO • HAGSTROM MAPS • BACHARACH PAGES 14/40/42/44 PAGE 95 PAGES 66-69 • DIAMOND • HANSON • BAG SUPPLY INC. PAGE 43 PAGE 47 PAGES 85-87 • DIXON • HEXCRAFT • BALTIMORE TOOL PAGES 45, 95 PAGES 11, 13 PAGE 42,43 • DURACELL • HK PORTER • BAYCO PAGES 54, 55 PAGE 23 PAGES 44-47 • DURABOND • HUOT • BERKLEY TOOL PAGE 59 PAGE 19, 129 PAGES 15-17, 123, 139 • EKLIND • ICE MELT INC. • BERNZOMATIC PAGE 11 PAGE 121 PAGE 131 • ENDERES • IDEAL • BETA PAGE 119 PAGES 63, 65 PAGES 66-68, 70+71, 78-85 • ENERGIZER • IRWIN • BLACKJACK PAGES 55 PAGES 17/19/21/23/38 PAGE 39 • EVERHARD 43/135 • BLITZ PAGE 121 • ITW BUILDEX PAGE 55 • FAST ORANGE PAGE 119 • BONDHUS PAGE 61 • JAMERCO DRIVE PINS PAGE 11 • FIRE POWER PAGE 111 • BOSCH PAGE 131 • JANITORIAL INC.
    [Show full text]
  • Two Slider Windows * Weatherstrip and Caulk to Seal
    * Two slider windows * Weatherstrip and caulk to seal the windows to the hardtop * Screws to attach the clamp ring to the slider window frame * Hardtop Retrofit Kit 1 Tools required for this project include a long-bladed utility knife for cutting the factory window adhesive, a chisel or other narrow scraper to remove remants of the adhesive, a cutting tool for trimming the window opening (more on this later in the instructions), and a nut driver/socket wrench for installing the window clamp ring screws. None of the tools required are things that a typical DIY-er might not have in their tool collection or couldn’t acquire at a very reasonable cost. The photos in these instructions show a side panel from that’s been cut from a factory hardtop with most of the work done on a workbench. In a typical installation the hardtop will be intact as it left the factory so the work will probably be done while the hardtop is still on the Jeep. None of the steps shown in this document are different when doing the work on a hardtop on a Jeep. The illustrations in these instructions are of a 4-door window installation. The 2-door window kit is installed in the same way. The first step of the process is to remove the factory windows. These are bonded in place by a bead of semi-soft adhesive and removal involves cutting the adhesive. If you’re not comfortable with this step, an automotive glass or body shop will probably be willing to do the removal step for you for a reasonable cost.
    [Show full text]
  • PLUMBING DICTIONARY Sixth Edition
    as to produce smooth threads. 2. An oil or oily preparation used as a cutting fluid espe cially a water-soluble oil (such as a mineral oil containing- a fatty oil) Cut Grooving (cut groov-ing) the process of machining away material, providing a groove into a pipe to allow for a mechani cal coupling to be installed.This process was invented by Victau - lic Corp. in 1925. Cut Grooving is designed for stanard weight- ceives or heavier wall thickness pipe. tetrafluoroethylene (tet-ra-- theseveral lower variouslyterminal, whichshaped re or decalescensecryolite (de-ca-les-cen- ming and flood consisting(cry-o-lite) of sodium-alumi earthfluo-ro-eth-yl-ene) by alternately dam a colorless, thegrooved vapors tools. from 4. anonpressure tool used by se) a decrease in temperaturea mineral nonflammable gas used in mak- metalworkers to shape material thatnum occurs fluoride. while Usedheating for soldermet- ing a stream. See STANK. or the pressure sterilizers, and - spannering heat resistantwrench and(span-ner acid re - conductsto a desired the form vapors. 5. a tooldirectly used al ingthrough copper a rangeand inalloys which when a mixed with phosphoric acid.- wrench)sistant plastics 1. one ofsuch various as teflon. tools to setthe theouter teeth air. of Sometimesaatmosphere circular or exhaust vent. See change in a structure occurs. Also used for soldering alumi forAbbr. tightening, T.F.E. or loosening,chiefly Brit.: orcalled band vapor, saw. steam,6. a tool used to degree of hazard (de-gree stench trap (stench trap) num bronze when mixed with nutsthermal and bolts.expansion 2. (water) straightenLOCAL VENT.
    [Show full text]
  • Countertop Mix
    Preparation: Make sure the frame is completely built before mixing the Concrete Countertop Mix. Be sure that the mixing bucket used is clean of any debris from prior use. Measure out all of the additives to be used prior to mixing. This will create a consistent mix when casting multiple pieces. Tools Required: • Concrete mixer or heavy duty ½” drill (600 RPM or less) • Drill/ driver and bits • Saw with a metal-cutting blade or hack saw blade w/ handle • Caulk gun • Rubber hammer • Trowel • Pliers • Carpenter square • Tape measure • 5 gallon bucket Materials Needed: • Melamine-coated particleboard • Coarse drywall screws PREMIUM CONCRETE • Colored Pigment (If desired) COUNTERTOP MIX™ • Potable water • Plastic sheeting High Strength ● Fast Setting ● Pourable • Styrofoam • Painters tape & packing tape • PVC pipe Uses: Advantages: • Silicone caulk (black or dark color) • Precast Countertops • High Strength-exceeds • Wire mesh, rebar, wire ties • Outdoor Kitchen or 5,000 psi at 28 days • Sanding block & palm sander Barbeque Top • Polymer Modified • Wood shims • Bar or Table Top • Pourable Consistency • Workbench or Utility Top • Sets in 18-24 Hours • Precast Wall Caps • Preblended - Just Add Helpful Items: Corporate Office: • Precast Mantels/Lintels Water Mendota Heights, MN 55120 www.tccmaterials.com www. tccmaterials.com Preparation Mixing 8 In 18-24 hours, you may remove the plastic from the 1 Make a form using ¾” melamine coated particleboard 5 Mix each 50# bag of Premium Concrete Countertop countertop surface and remove all the screws holding to the dimensions desired. Mix™ in a five gallon bucket or mortar mixer with 5 to 5.5 the form together.
    [Show full text]
  • How to Cut and Install Moulding
    How to Cut and Install Moulding Start with the Right Tools for the Job Some of the tools needed are: • Safety glasses • Power miter saw – We recommend using carbide saw blade with 80 teeth or more. Left and Right hand positioning – the side of the trim you • Miter box and hand are cutting is as important as its position on the saw table. saw – They have The positions are illustrated above. limited angle adjustment (not recommended for Vertical Position Miters crown). Use this technique for cutting • Coping saw – Only baseboard, chair rail, quarter needed if you choose round, and splice miters. the coping technique Inside corners - A left hand to install the moulding. inside corner is shown in the • Angle gage – To create the correct miter, you must photo. determine the wall corner angle. Step 1 - To accomplish this, place • Glue – To adhere the miter joints (we strongly the trim on the saw table in the recommend gluing all joints). left hand vertical position and • Hammer & nails or a pneumatic nail gun. rotate the angle gage “clock • Other tools may include a tape measure, pencil, wise” to 45°, or the desired angle C-clamp, putty and caulk. setting, and make the cut. Step 2 - To cut the mating piece simply rotate the table angle Determine the Amount of gage to the opposite 45° or desired angle, and place the Moulding to Buy next piece of trim on the saw table in the right hand verti - You must decide where the cal position and cut the trim. mouldings are to be used and measure the distances.
    [Show full text]
  • Workbench No
    TOOL REVIEW: 9 Router Tables Under$ 300 TM Woodworking To Improve Your Home Storage with Style! Cedar Garden Shed Plus: ● Stack 'em Up Storage Bins ● Trouble-Free Pocket Doors ● 5 Energy-Saving Tune-Up Tips www.WorkbenchMagazine.com No 267 September/October 2001 Contents 16 16 Cedar Garden Shed Why settle for oversized pre-fab when you can build the perfect-sized shed yourself from scratch? We’ll show you some construction techniques that can be used in all types of projects. 18 Modular Design . Basic framing makes building this shed simple. 20 Roofing Systems . Learn how to build rafters and install shingles. 22 Trim and Siding ...Pick up a few tips for applying cedar lap siding. 18 20 22 24 28 Easy Way Install a to Hang Trouble-Free Double Doors Pocket Door Hanging your own No room for a hinged doors is the way to go door? No problem. when you want to save We’ll show you how to money and get just the install a door that look you’re after for “disappears” into a your new shed. pocket in the wall. 24 28 2 WORKBENCH ■ SEPTEMBER | OCTOBER 2001 TM 34 34 Router Table Review A router table doesn’t have to be expensive to get the job done. We tested nine models — all for less than $300. Find out which one takes the “top table” award. 40 Stackable Storage Bins A simple system of interlocking keys and notches makes these stacking storage bins as sturdy as they are versatile. 40 46 46 5 Energy-Saving Tune-Up Tips Practical ways to button-up your home and take the chill out of those winter energy bills.
    [Show full text]
  • 2020 Therma-Tru Site Manual
    Installation Installation ............................................................................... Site 1 Finishing Instructions Finishing .................................................................................. Site 2 Maintenance Maintenance ............................................................................ Site 3 Trouble Shooting Trouble Troubleshooting ..................................................................... Site 4 Replacement Repair and Repair and Replacement ........................................................ Site 5 Index Index .................................................................................................i Installation Installation Pre-Hung Unit Installation ........................................................................................................................................... 1.3 Pre-Hung Venting Unit Installation ............................................................................................................................1.11 Pre-Hung Arch/Radius Unit Installation ................................................................................................................... 1.19 MPLS Strike Installation Instructions - Standard Inswing Shootbolt .................................................................... 1.21 MPLS Strike Installation Instructions - Impact Inswing Shootbolt ........................................................................ 1.24 MPLS Strike Installation Instructions - Standard Outswing Shootbolt ................................................................
    [Show full text]
  • TITLE Social Research in North American Moisture-Deficient Regions
    DOCUMENT RESUME ED 101 871 RC 008 292 AUTHOR Bennett, John g., Ed. TITLE Social Research in North American Moisture-Deficient Regions. INSTITUTION American Association for the Advancement ofScience, Washington, D.C.; New Mexico State Univ., Las Cruces.; Rocky Mountain SocialScience Association, Laramie, Wyo. PUB DATE 66 NOTE 76p.: Symposium held during the 42nd annualmeeting of the Southwestern and RockyMountain Division of the American Association for the Advancementof Science, Las Cruces, N.M., May 4, 1966. Forrelated document, see RC 008 293 EDRS PRICE MF -S0.76 HC-$4.43 PLUS POSTAGE DESCRIPTORS *Adjustment (to Environment); Agriculture;*Climatic Factors; *Ecology; Economics; EnvironmentalResearch; Humidity; *Rural Areas; *Socioeconomic Influences; Speeches; Technological Advancement IDENTIFIERS *Great Plains ABSTRACT Five papers presented at the 9thsymposium held during the 42nd annual meeting of theSouthwestern and Rocky Mountain Division of the American Association for theAdvancement of Science are: (1) "Do We Need aSociology of Arid Regions*?; (2) "Deficit Creating Influences for Role Performanceand Status Acquisition in Sparsely Populated Regions of theUnited States*:(3) "Ecology, Economy and Society in an AgriculturalRegion of the Northern Great Plains "; (4) The Problem of Drought Perception*:and (5) "Technological Conservatism in CattleRanching as an Adaptive Process ". The papers, centering on anecological viewpoint, aiv to suggest possibilities of basicresearch on sociological adaptations in moisture-deficient regions. Discussions covermodern agrarian and town populations in the GreatPlains and neighboring semiarid regions. (NQ) WIWI fatSI BEST OR ',SALTS*. %I S.DEPARTMSNTWELP ARE EDUCasON I pc SATSONAt.144STSTUTE DOUCATiON REPRO HAS SEEN FROM ¶ losDOCUMENT RECEIVED TLY AS ION ORIGIN DUCED EXACOR OROLNSEAT WSW OROPINIONS DIE PERSONPOINTS OP REPRE AT IND IT NECESSARIL E OF ST ATED DONOT N, ICTY ut *ENT Of0sCIAONIATOOOR EDUCATION Social Research in North American Moisture Deficient Regions Edited by: John W.
    [Show full text]
  • Caulking and Sealant Information
    Technical Bulletin 5.002 March 2016 Caulking and Sealant Information General Information: Most caulking materials are classified as a waterproof filler and sealer. Properly applied caulking will seal joints and cracks from the intrusion of water, air, dust, insects, pollution and noise. Choosing the right caulk and correctly applying it will reduce failures by keeping shrinkage and splitting to a minimum. Choosing the Correct Caulk: Understanding the characteristics and limitations of caulk is vital to the caulking’s performance. How the caulk will react to ultraviolet light and it’s compatibility to the substrate are two important factors in determining your selection. Another essential factor to consider is whether you are using the caulk indoors or outdoors. Using certain types of caulk indoors may emit volatile organic compounds (VOCs) impacting the air quality. One of the most important factors when selecting a caulk is the movement capacity. This is crucial if the joint is expected to move. There are three types of caulk to consider when movement is a factor: low-movement medium-movement caulk high-movement caulk Low-movement – Limited to joints that are not subjected to constant expansion and contraction or deflection. Low movement caulk is not very flexible once it sets and is negatively affected by sunlight and extremes of both hot and cold. Medium-movement – Ideal for slow moving joints such as masonry control joints. Recommended for use where the maximum movements are below 25 percent of the joint width. High-Movement – Suitable for large or fast moving joints, such as those between dissimilar materials like metal and concrete.
    [Show full text]
  • Acoustical Solutions Center
    Acoustical Solutions Center TM www.grabberman.com “The Professional’s Choice”TM Index About Grabber Acoustical Eye-Lag Screws 3 GRABBER is a leading distributor of quality products built for construction professionals. Coarse thread eye-lags for attaching to wood 3 For contractors, quality is everything. Products must be 100% reliable and durable to Self-piercing steel deck eye-lags 3 meet the demands of an increasingly fast-paced and productivity-minded profession. Self-drilling steel deck eye-lags 3 The construction industry rewards innovations that achieve real gains in efficiency, Acoustical Lag Drivers 4 performance, and job quality. All GRABBER products must meet this high standard of Lag driver 4 excellence. Grabber engineers it’s fastener products to be superior to all other products in Lag pole 4 their class. J-master installation tool 4 Two hole angle bracket 4 Grabber’s core line of products include fasteners for a variety of wood, metal, and drywall Angle clip & pin assembly 4 applications. GRABBER fasteners are regarded as the best in the industry, punctuated by Acoustical Hangers 5 the fact that it’s competitors have had to duplicate Grabber fastener designs. GRABBER Angle clip & pin assembly 5 also distributes many other product lines for the commercial and residential construction Pre-tied angle clip & pin assebembly 5 industries, including proprietary construction equipment, drywall tools and materials, Pre-tied wire and clips 5 Nitroset pin & clip assembly 6 power drives, adhesives, and accessories. Nitroset pre-tied
    [Show full text]
  • Tools and Equipment
    TOOLS AND EQUIPMENT EIFS | STUCCO | FOAM demandproducts.com How to Order Our products are available through distributors located throughout the world. If you cannot find a distributor in your area, email eifs@demandproducts. com or call, and we will assist you in finding one. Our operation hours are from 8:00 am to 5:00 pm Monday through Friday, EST. Our fax machines & email operate around the clock. FAX: 1.888.534.8383 E-MAIL: [email protected]. ALL PRICES ARE SUBJECT TO CHANGE WITHOUT NOTICE (PRICES ARE IN US DOLLARS) Return Policy Demand Products Inc., will accept the return of merchandise for exchange or credit only with advance written authorization. Returned materials will be credited at the actual cost paid as determined by the proof of purchase, LESS ALL FREIGHT COSTS paid by Demand Products Inc. We do not accept returns on chemicals or coatings and some electronics. Returns must be made within 15 days of invoice and must be in new, re-stockable condition upon receipt. Materials returned must be shipped prepaid. Discontinued items and custom orders cannot be returned. Returns subject to minimum 15% restocking fee. Warranty All of our products carry an unconditional 6 month guarantee. Demand Products must be notified within 48 hours of receipt of defective or damaged merchandise or shortages. Any equipment or tools that are disassembled without prior written consent from Demand Products will have the warranty voided. Defective products will either be replaced or repaired at no charge. Abused tools will be repaired and returned only if the customer consents to charges.
    [Show full text]
  • Pcbs Window Caulk Removal
    Job Safety Analysis Safety Information for The University of North Carolina at Chapel Hill All UNC Shops Polychlorinated Biphenyls (PCBs) Window Caulk Removal **The term “caulk” will be used to describe caulking, sealants, or paints. Title Work Task Hazards Controls Pre-Operation and 1. Contact EHS concerning the 1. Not having correct tools and 1. Understand the building/structure that work will Preparing for the Job presence of PCBs, asbestos and/or training to complete be performed. lead. abatement. 2. Assess foliage or other obstacles that might 2. Completed the Training Course 2. Injury or possible death. impede access. titled, “Management of PCBs in 3. Assess for any electrical 3. Ladders or scaffolding to assist with heights. caulking and Sealants” and Hand and hazards, overhead issues. Read the JSAs for ladders, scaffolds, man lifts Power Tools Training. 4. Inhalation hazard associated and fall protection. 3. Based upon the condition of the with PCBs. 4. Wet methods and HEPA vacuum are essential caulk, tools may include utility knife, 5. Skin, eye, ingestion and dust control requirements. chisel, hammer, crowbar, putty knife, inhalation hazards. 5. Review all SDS for the solvent and new caulk scraper, electrical joint cutter with 6. High winds can spread application. oscillating blade, and HEPA vacuum. contamination beyond the For elastic and soft caulking work area. (primarily in areas protected from 7. Heat or dry removal will sunlight and weather or located increase the inhalation risk indoors), use utility knife, putty and contamination. knife, or scraper. For hard and brittle (aged and weather-exposed caulks), use chisel, hammer, crowbar, electrical joint cutter with oscillating blade.
    [Show full text]