Stratix 5700 Switches (1783-BMS) Armorstratix 5700 Switches (1783-ZMS) Stratix 8000 and 8300 Switches (1783-MS, 1783-RMS, 1783-MX) Important User Information
Total Page:16
File Type:pdf, Size:1020Kb
User Manual Stratix Managed Switches Stratix 5400 Switches (1783-HMS) Stratix 5700 Switches (1783-BMS) ArmorStratix 5700 Switches (1783-ZMS) Stratix 8000 and 8300 Switches (1783-MS, 1783-RMS, 1783-MX) Important User Information Read this document and the documents listed in the additional resources section about installation, configuration, and operation of this equipment before you install, configure, operate, or maintain this product. Users are required to familiarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws, and standards. Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required to be carried out by suitably trained personnel in accordance with applicable code of practice. If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired. In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the use or application of this equipment. The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or liability for actual use based on the examples and diagrams. No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or software described in this manual. Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation, Inc., is prohibited. Throughout this manual, when necessary, we use notes to make you aware of safety considerations. WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous environment, which may lead to personal injury or death, property damage, or economic loss. ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death, property damage, or economic loss. Attentions help you identify a hazard, avoid a hazard, and recognize the consequence. IMPORTANT Identifies information that is critical for successful application and understanding of the product. Labels may also be on or inside the equipment to provide specific precautions. SHOCK HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that dangerous voltage may be present. BURN HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that surfaces may reach dangerous temperatures. ARC FLASH HAZARD: Labels may be on or inside the equipment, for example, a motor control center, to alert people to potential Arc Flash. Arc Flash will cause severe injury or death. Wear proper Personal Protective Equipment (PPE). Follow ALL Regulatory requirements for safe work practices and for Personal Protective Equipment (PPE). Allen-Bradley, ArmorStratix, Logix5000, Rockwell Automation, Rockwell Software, RSLinx, RSLogix, RSNetWorx, Stratix 2000, Stratix 5700, Stratix 8000, Stratix 8300, Studio 5000, Studio 5000 Automation Engineering & Design Environment, and Studio 5000 Logix Designer are trademarks of Rockwell Automation, Inc. Trademarks not belonging to Rockwell Automation are property of their respective companies. Summary of Changes This manual contains new and updated information. Changes throughout this revision are marked by change bars, as shown to the right of this paragraph. New and Updated This table contains the changes made to this revision. Information Topic Page Stratix 5400 switch family description 18 Stratix 5400 software features 21 Stratix 5400 hardware features 22 Stratix 5400 templates 23 Stratix 5400 installation 27 Stratix 5400 Express Setup button 121 Stratix 5400 SD card 125, 144 Precision time protocol (PTP) configuration on the VLAN of a trunk port 159 Stratix 5400 time synchronization in the Logix Designer application 162 Stratix 5400 default multicast groups 183 Stratix 5400 Layer 3 routing 240 Stratix 5400 front panel and status indicators 269 Stratix 5400 Display Mode switch 272 Stratix 5400 data types 312 Stratix 5400 port assignments 364 Stratix 5400 port numbering 370 Stratix 5400 cables and connectors 391 Rockwell Automation Publication 1783-UM007B-EN-P - March 2015 3 Summary of Changes Notes: 4 Rockwell Automation Publication 1783-UM007B-EN-P - March 2015 Table of Contents Preface Studio 5000 Environment . 13 Access Product Release Notes . 14 Additional Resources . 15 Chapter 1 About the Switches EtherNet/IP CIP Interface . 18 CIP Network Connections. 19 EtherNet/IP QuickConnect Technology. 19 Lite Versus Full Firmware Features (Stratix 5700 switches) . 20 Software Features . 21 Hardware Features . 22 Memory Allocation . 23 Stratix 5400 Templates . 23 Stratix 5700 and ArmorStratix 5700 Templates. 24 Stratix 8000 and 8300 Templates . 25 Chapter 2 Install Stratix 5400 Switches Overview . 30 Parts List and Required Tools . 32 Install or Remove the SD Card . 33 Verify Switch Operation . 34 Mount the Switch on a DIN Rail . 35 Remove the Switch from the DIN Rail. 35 Ground the Switch . 36 Wire the Switch DC Power Source . 37 Attach the Switch Power Connectors . 40 Install an SFP Module . 41 Remove SFP Modules from SFP Module Slots . 43 Wire the External Alarms . 44 Attach the Alarm Relay Connector to the Switch . 47 Connect to 10/100 and 10/100/1000 Ports . 47 Connect to 10BASE-T, 100BASE-TX, or 1000BASE-T Ports . 48 Connect to PoE Ports . 49 Connect to SFP Module Ports . 49 Connect to a Dual-purpose Port. 50 Chapter 3 Install Stratix 5700 Switches Overview . 53 Parts List and Required Tools . 55 Install or Remove the SD Card . 56 Verify Switch Operation . 58 Mount the Switch on a DIN Rail . 59 Remove the Switch from the DIN Rail. 61 Ground the Switch . 61 Wire the Switch DC Power Source . 63 Rockwell Automation Publication 1783-UM007B-EN-P - March 2015 5 Table of Contents Attach the Switch Power Connectors . 67 Wire the Power over Ethernet DC Power Source. 68 Attach the PoE Power Connector. 69 Install an SFP Module . 70 Remove SFP Modules from SFP Module Slots . 71 Wire the External Alarms . 73 Attach the Alarm Relay Connector to the Switch . 76 Connect to 10/100 and 10/100/1000 Ports . 76 Connect to 10BASE-T, 100BASE-TX, or 1000BASE-T Ports . 77 Connect to PoE Ports. 78 Connect to SFP Module Ports. 78 Connect to a Dual-purpose Port . 79 Chapter 4 Install ArmorStratix 5700 Switches Overview . 82 Parts List and Required Tools . 83 Install or Remove the SD Card . 85 Verify Switch Operation . 86 Mount the Switch . 87 Ground the Switch . 87 Connect the Switch to a DC Power Source . 89 Power over Ethernet . 89 Wire External Alarms. 90 Connect to 10/100 and 100/1000 Ports. 91 10/100 Ports . 91 100/1000 Ports. 92 10/100 PoE Ports. 92 Chapter 5 Install Stratix 8000 and 8300 Overview . 95 Switches Parts List and Required Tools . 96 Attach Expansion Modules (optional). 99 Mount the Switch on a DIN Rail . 101 Mount the Switch on a Wall or Panel . 102 Install an SFP Module (optional) . 103 Ground the Switch . ..