DOCSLIB.ORG

Miniature Stirling-Type Pulse-Tube Refrigerators

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Miniature Stirling-Type Pulse-Tube Refrigerators Miniature Stirling-type pulse-tube refrigerators Citation for published version (APA): Hooijkaas, H. W. G. (2000). Miniature Stirling-type pulse-tube refrigerators. Technische Universiteit Eindhoven. https://doi.org/10.6100/IR534736 DOI: 10.6100/IR534736 Document status and date: Published: 01/01/2000 Document Version: Publisher’s PDF, also known as Version of Record (includes final page, issue and volume numbers) Please check the document version of this publication: • A submitted manuscript is the version of the article upon submission and before peer-review. There can be important differences between the submitted version and the official published version of record. People interested in the research are advised to contact the author for the final version of the publication, or visit the DOI to the publisher's website. • The final author version and the galley proof are versions of the publication after peer review. • The final published version features the final layout of the paper including the volume, issue and page numbers. Link to publication General rights Copyright and moral rights for the publications made accessible in the public portal are retained by the authors and/or other copyright owners and it is a condition of accessing publications that users recognise and abide by the legal requirements associated with these rights. • Users may download and print one copy of any publication from the public portal for the purpose of private study or research. • You may not further distribute the material or use it for any profit-making activity or commercial gain • You may freely distribute the URL identifying the publication in the public portal. If the publication is distributed under the terms of Article 25fa of the Dutch Copyright Act, indicated by the “Taverne” license above, please follow below link for the End User Agreement: www.tue.nl/taverne Take down policy If you believe that this document breaches copyright please contact us at: [email protected] providing details and we will investigate your claim. Download date: 28. Sep. 2021 Miniature Stirling-Type Pulse-Tube Refrigerators PROEFSCHRIFT ter verkrijging van de graad van doctor aan de Technische Universiteit Eindhoven, op gezag van de Rector Magnificus, prof.dr. M. Rem, voor een commissie aangewezen door het College voor Promoties in het openbaar te verdedigen op dinsdag 13 juni 2000 om 16.00 uur door Herbert Willem Gerrit Hooijkaas geboren te Schoonhoven Dit proefschrift is goedgekeurd door de promotoren: prof.dr. A.T.A.M. de Waele en prof.dr. G. Thummes Druk: Universiteitsdrukkerij TUE CIP-DATA LIBRARY TECHNISCHE UNIVERSITEIT EINDHOVEN Hooijkaas, Herbert Willem Gerrit Miniature Stirling-type Pule-Tube Refrigerators / by Herbert Hooijkaas. - Eindhoven: Technische Universiteit Eindhoven, 2000. - Proefschrift. - ISBN 90-386-1559-0 NUGI 812 Trefw.: pulsbuis koeler / regenerator / cryogenie / thermodynamica Subjects: pulse-tube refrigerator / regenerator / cryogenics / thermodynamics Aan mijn vader Abstract ABSTRACT Pulse-tube refrigerators have the potential to be widely applied for producing low- temperatures. The main benefit of these systems is the absence of moving mechanical parts at the regions of low temperature. This lowers the induced mechanical vibrations significantly and strongly improves the reliability of these systems. Other benefits are lower manufacturing costs and less magnetic noise. This research focuses on the development of miniature Stirling-type pulse-tube refrigerators. These systems are characterized by the direct connection of cooler and compressor and generally have a driving frequency between 20 and 60 Hz. The desired cooling power of the considered systems is 0.5-1.0 W at a temperature of 80 K and an input power of 40 W. In the development of these systems, as presented in this thesis, first the system is analyzed theoretically. Based on the conservation of mass, the equation of motion, the conservation of energy, and the equation of state of a real gas a general model of the pulse-tube refrigerator is made. The general model is specified for low-amplitude applications: a condition that is generally fulfilled by Stirling-type pulse tubes. Assuming this a harmonic approximation can be applied. The use of the harmonic approximation simplifies the differential equations of the model, as the time-dependency can be solved explicitly and separately from the other dependencies. The model applies only to systems in the steady state. Time dependent effects, such as the cool-down, are not described. From the relations the system performance is analyzed. Next, the effect of some conceptual improvements is analyzed. The harmonic model is implemented in a simulation program. The relations are linearized in this program and solved iteratively. In the iterations, the relations for mass accumulation and pressure drop are calculated simultaneously, while the temperature profile is calculated in a separate routine. This method is applied, as the mutual sensibility of these relations is rather weak and the calculation scheme becomes less complicated. In addition to the theoretical model and the simulation program, also experimental pulse tubes are developed. The model is validated with these systems. Some conceptual improvements, such as the inertance tube and the second inlet, are investigated experimentally. The influence of the phase angle, which is important I Miniature Stirling-Type Pulse-Tube Refrigerators for the efficiency, is investigated by means of a warm-end expander. This allows adjustment to any value of the phase angle. The experiments show that for the highest efficiencies, the compression of the gas in the tube should be carried out by a gas flow, which does not flow through the regenerator. Experimentally it has been shown that a cooling power of 400-500 mW at a temperature of 80 K can be achieved with the current technology, at input powers of 40 to 50 W. However, in the near future a cooling power of 1 W must be attainable, if optimizations are applied to the regenerator, regarding the matrix structure and the geometry. This has a high potential, as the regions of high flow resistance and relatively low heat-storage capacity are spatially separated. A modification of the different heat exchangers and the flow straightners in the tube will contribute to future improvements as well. Based on the experimental results and the model, a new pulse tube, which focuses on the performance and the producibility, is developed. Concluding: the miniature pulse tube technology is ready for low-power application at cryogenic temperatures. This holds especially for applications that require a low level of vibrations or high reliability. In the near future, the pulse-tube refrigerator might become a good substitute for the other coolers, as its manufacturing costs are lower as well. II Contents CONTENTS Abstract I Contents III Nomenclature VII Chapter 1 Introduction 1 1.1 General introduction 2 1.2 Introduction to this thesis 6 Bibliography 7 Chapter 2 Dynamics of the non-ideal gas 9 2.1 Equation of state 10 2.2 Gas distribution 10 2.2.1 Conservation of mass 10 2.2.2 Equation of motion 12 2.3 Thermodynamic properties 13 2.4 Energy conservation in an open volume 15 Bibliography 21 Chapter 3 Pulse-tube model for harmonic signals 23 3.1 Practical operation 24 3.2 Mathematical properties 25 3.2.1 Characteristics 25 3.2.2 Time derivations 25 3.2.3 Complex notation 25 3.2.4 Multiplication of signals 26 3.3 The gas behavior 27 3.4 Temperature oscillations 28 3.5 Energy flow 32 3.6 Gas flow and accumulation 36 Bibliography 42 III Miniature Stirling-Type Pulse-Tube Refrigerators Chapter 4 Model analysis 43 4.1 Flow properties 44 4.2 Cooling power and losses 46 4.3 Optimization of the idealized orifice pulse tube 50 4.4 Conceptual improvements 51 4.4.1 Double-inlet pulse-tube refrigerator 51 4.4.2 Inertance pulse-tube refrigerator 52 4.4.3 Warm-end expander pulse-tube refrigerator 54 4.4.4 Multistage pulse-tube refrigerator 55 4.4.5 Multi-bypass pulse-tube refrigerators 57 Bibliography 58 Chapter 5 Simulation model 59 5.1 The pressure wave and mass distribution 60 5.1.1 Pressure amplitude estimation in the buffer 61 5.2 Average temperature profile 63 5.2.1 Heat exchanger temperatures 65 5.3 Simulation structure 69 5.3.1 Standard pulse-tube refrigerators 69 5.3.2 More advanced pulse-tube refrigerators 70 5.3.3 Pulse tube optimizations 72 5.4 The system parameters 73 5.4.1 Effective heat exchange and storage function; G 73 5.4.2 The flow resistance; RL 75 5.4.3 The mass storage capacity; CL 76 5.4.4 The damping factor; DL 77 5.5 Convergence of the iteration loops 78 Bibliography 79 Chapter 6 Simulations and experiments 81 6.1 Experimental setup 82 6.1.1 Pressure measurements 82 6.2 Inline pulse tubes 84 6.2.1 Dimensions 84 IV Contents 6.3 Results 86 6.3.1 Influence of the operational settings 86 6.3.1.1 Flow resistance 86 6.3.1.2 Frequency 88 6.3.1.3 Input-power 89 6.3.2 Temperature profiles 90 6.3.3 Discussion 91 6.4 U-shaped pulse tubes 91 6.4.1 Dimensions 92 6.4.2 Orifice pulse tube 93 6.4.2.1 Flow resistance 94 6.4.2.2 Buffer volume 95 6.4.2.3 Heat exchanger configurations 96 6.4.3 Inertance pulse tube 97 6.4.4 Double-inlet inertance pulse tube 100 6.5 The influence of the warm-end phase angle 101 6.5.1 Simulations 102 6.5.2 Warm end expander pulse tube 103 6.5.2.1 Active expander operation 103 6.5.2.2 Passive expander operation 104 6.5.3 Discussion 107 6.6 The pulse-tube prototype 107 6.6.1 Dimensions 107 6.6.2 Results 108 6.6.3 Discussion 109 Bibliography 109 Chapter 7 Discussion 111 Samenvatting 113 Dankwoord 115 Curriculum vitae 116 V Nomenclature NOMENCLATURE Greek symbols L scaled heat exchange [1/s] G scaled heat capacity D spatial difference operator Ñc critical gradient a isothermal pressure dependence l thermal conductivity [W/mK] of non-ideality x effective flow friction factor [1/m] a heat exchange coefficient [W/m2K] r density [kg/m3] b isobaric temperature dependence s inverse of flow resistance [ms] of non-ideality t characteristic heat transfer time [s] g adiabatic expansion coefficient fm mass flow [kg/s] 3 dth thermal penetration depth [m] fV volume flow [m /s] e linearity factor c adiabatic pressure dependence z inverse vol.
Load more

Recommended publications
  • Thermodynamic Analysis of GM-Type Pulse Tube Coolers Q Y.L
    Cryogenics 41 &2001) 513±520 www.elsevier.com/locate/cryogenics Thermodynamic analysis of GM-type pulse tube coolers q Y.L. Ju *,1 Cryogenic Laboratory, Chinese Academy of Sciences, P.O. Box 2711, Beijing 100080, People's Republic of China Received 29 January 2001; accepted 28 June 2001 Abstract The thermodynamic loss of rotary valve and the coecient of performance &COP) of GM-type pulse tube coolers &PTCs) are discussed and explained by using the ®rst and second laws of thermodynamics in this paper. The COP of GM-type PTC, based on two types of pressure pro®les, the sinusoidal wave inside the pulse tube and the step wave at the compressor side, has been derived and compared with that of Stirling-type PTC. Result shows that additional compressor work is needed due to the irreversible entropy productions in the rotary valve thereby decreasing the COP of GM-type PTC. The eect of double-inlet mode on the COP of PTC has distinct improvement at lower temperature region &larger TH=TL). It is also shown that the COP of GM-type PTC is independent of the shape of the pressure pro®les in the ideal case of no ¯ow resistance in the regenerator. Ó 2001 Elsevier Science Ltd. All rights reserved. Keywords: Pulse tube cooler; GM-type; Thermodynamic analysis 1. Introduction achieved [13]. All these machines use a compressor and a valve system to produce pressure oscillation in the In general pulse tube cooler &PTC) requires a phase cooler system. They are called GM-type PTCs. shifter system, located at the hot end of the pulse tube, A GM-type PTC, shown in Fig.
    [Show full text]
  • MODELING and ANALYSIS of PULSE TUBE REFRIGERATOR 1Nishant Solanki, 2Nimesh Parmar
    Solanki et al., International Journal of Advanced Engineering Technology E-ISSN 0976-3945 Research Paper MODELING AND ANALYSIS OF PULSE TUBE REFRIGERATOR 1Nishant Solanki, 2Nimesh Parmar Address for Correspondence 1Student, M.E. (Thermal Engineering), Gandhinagar Institute of Technology, Gandhinagar, Gujarat, India 2Asst. Professor, Mechanical Engineering Department, Gandhinagar Institute of Technology, Gandhinagar, Gujarat, India ABSTRACT: Cryogenics comes from the Greek word “kryos”, which means very cold or freezing and “genes” means to produce. Cryogenics is the science and technology associated with the phenomena that occur at very low temperature, close to the lowest theoretically attainable temperature. In this research paper, three dimensional model of pulse tube refrigerator is developed in ANSYS CFX and compared it with experimental results. It shows good agreement with experimental results with ANSYS CFD results. KEYWORDS : Pulse tube refrigerator, ANSYS CFD INTRODUCTION: volume on the thermodynamic performance of The pulse tube refrigerators (PTR) are capable of various components in a simple orifice and a double cooling to temperature below 123K. Unlike the inlet pulse tube cooler by combining a linearized ordinary refrigeration cycles which utilize the vapour model with a thermodynamic analysis. The results compression cycle as described in classical reveal that the performance of the pulse tube cooler is thermodynamics, a PTR implements the theory of significantly affected when the reservoir to pulse tube oscillatory compression and expansion of the gas volume ratio is less than 5, which helps the design of within a closed volume to achieve desired a practical pulse tube cooler. refrigeration. Being oscillatory, a PTR is a non steady Y.L. He, C.F.
    [Show full text]
  • Mathematical Analysis of Pulse Tube Cryocoolers Technology
    Global Journal of researches in engineering Electrical and electronics engineering Volume 12 Issue 6 Version 1.0 May 2012 Type: Double Blind Peer Reviewed International Research Journal Publisher: Global Journals Inc. (USA) Online ISSN: 2249-4596 & Print ISSN: 0975-5861 Mathematical Analysis of Pulse Tube Cryocoolers Technology By Shashank Kumar Kushwaha , Amit medhavi & Ravi Prakash Vishvakarma K.N.I.T Sultanpur Abstract - The cryocoolers are being developed for use in space and in terrestrial applications where combinations of long lifetime, high efficiency, compactness, low mass, low vibration, flexible interfacing, load variability, and reliability are essential. Pulse tube cryocoolers are now being used or considered for use in cooling infrared detectors for many space applications. In the development of these systems, as presented in this paper, first the system is analyzed theoretically. Based on the conservation of mass, the equation of motion, the conservation of energy, and the equation of state of a real gas a general model of the pulse tube refrigerator is made. The use of the harmonic approximation simplifies the differential equations of the model, as the time dependency can be solved explicitly and separately from the other dependencies. The model applies only to systems in the steady state. Time dependent effects, such as the cool down, are not described. From the relations the system performance is analyzed. And also we are describing pulse tube refrigeration mathematical models. There are three mathematical order models: first is analyzed enthalpy flow model and heat pumping flow model, second is analyzed adiabatic and isothermal model and third is flow chart of the computer program for numerical simulation.
    [Show full text]
  • Vapor Precooling in a Pulse Tube Liquefier
    Presented at the 11th International Cryocooler Conference June 20-22, 2000 Keystone, Co Vapor Precooling in a Pulse Tube Liquefier E.D. Marquardt, Ray Radebaugh, and A.P. Peskin National Institute of Standards and Technology Boulder, CO 80303 ABSTRACT Experiments were performed to study the effects of introducing vapor into a dewar where a coaxial pulse tube refrigerator was used as a liquefier in the neck of the dewar. We were concerned about how the introduction of vapor might impact the refrigeration load as the vapor barrier in the neck of the dewar is disturbed. Three experiments were performed where the input power to the cooler was held constant and the nitrogen liquefaction rate was measured. The first test introduced the vapor at the top of the dewar neck. Another introduced the vapor directly to the cold head through a small tube, leaving the neck vapor barrier undisturbed. The third test placed a heat exchanger partway down the regenerator where the vapor was pre-cooled before being liquefied at the cold head. This experiment also left the neck vapor barrier undisturbed. Compared to the test where the vapor was introduced directly to the cold head, the heat exchanger test increased the liquefaction rate by 12.0%. The experiment where vapor was introduced at the top of the dewar increased the liquefaction rate by 17.2%. A computational fluid dynamics model was constructed of the dewar neck and liquefier to show how the regenerator outer wall acted as a pre-cooler to the incoming vapor steam, eliminating the need for the heat exchanger.
    [Show full text]
  • Effects of Acoustic and Fluid Dynamic Interactions in Resonators: Applications in Thermoacoustic Refrigeration a Thesis Submitt
    Effects of Acoustic and Fluid Dynamic Interactions in Resonators: Applications in Thermoacoustic Refrigeration A Thesis Submitted to the Faculty of Drexel University by Dion Savio Antao in partial fulfillment of the requirements for the degree of Doctor of Philosophy June 2013 ii © Copyright 2013 Dion Savio Antao. All Rights Reserved iii If you can trust yourself when all men doubt you, But make allowance for their doubting too; If you can meet with triumph and disaster And treat those two imposters just the same; Or watch the things you gave your life to broken, And stoop and build 'em up with wornout tools; Rudyard Kipling, If, ln. 2, 6 and 8 Omni autem cui multum datum est multum quaeretur ab eo et cui commendaverunt multum plus petent ab eo LVKE 12:48 iv Dedications I would like to first dedicate this dissertation to my role models, my biggest critics and my most fervent supporters, my mum and dad. Next I would like to dedicate this dissertation to my sister; may it motivate her to achieve her own goals and ambitions in life and reach for the stars. Finally, I would like to dedicate this dissertation to the people of India; the taxpayers whose contributions helped provide for my education (from kindergarten to university) and that of so many others. v Acknowledgements At this point, it is important to thank the people and recognise and acknowledge the contributions that made this dissertation possible. First I must thank my dad and mum for their constant love and support and for teaching me (in both words and deeds) that hard work and perseverance are the most important keys to success.
    [Show full text]
  • Journal Abstract3.Pdf
    Indian Journal of Cryogenics Vol. 34. No. 1-4, 2009 CONTENTS (Part -A of NSC-22 Proceedings) Preface Plenary Paper 1. Hundred years liquid helium 1 — A.T.A.M. de Waele 2. Cryogenics in launch vehicles and satellites 11 — Dathan M.C, Murthy M.B.N and Raghuram T.S 3. Nano-Kelvins in the laboratory 18 — Unnikrishnan. C. S. Cryo Component Development & Analysis 4. Development of plate and fin heat exchangers 27 — Mukesh Goyal, Rajendran Menon, Trilok Singh 5. Helium Liquefaction/Refrigeration System Based on Claude Cycle: A Parametric Study 33 — Rijo Jacob Thomas, Sanjay Basak, Parthasarathi Ghosh and Kanchan Chowdhury 6. Computation of liquid helium two phase flow in horizontal and vertical transfer lines 39 — Tejas Rane, Anindya Chakravarty, R K Singh and Trilok Singh 7. Experience in design and operation of a cryogenics system for argon cover gas 45 purification in LMFBRs — B.Muralidharan, M.G.Hemanath, K.Swaminathan, C.R.Venkatasubramani, A.Ashok kumar, Vivek Nema and K.K.Rajan 8. Design and implementation of an adiabatic demagnetization set up on a dilution refrigerator 51 to reach temperatures below 100mK — L. S. Sharath Chandra, Deepti Jain, Swati Pandya, P. N. Vishwakarma and V. Ganesan 9. Thermal design of recuperator heat exchangers for helium recondensation 57 systems using hybrid cryocoolers — G.Jagadish, G.S.V.L.Narasimham, Subhash Jacob 10. Experimental investigation on performance of aluminum tape and multilayer insulation 65 between 80 K and 4.2 K — Anup Choudhury, R S Meena, M Kumar, J Polinski, Maciej Chorowski and T S Datta 11. Finite element analysis of a spiral flexure bearing for miniature linear compressor 71 — Gawali B.
    [Show full text]
  • Numerical Analysis of Double Inlet Two-Stage Inertance Pulse Tube Cryocooler
    International Journal of Advanced Technology and Engineering Exploration, Vol 8(79) ISSN (Print): 2394-5443 ISSN (Online): 2394-7454 Research Article http://dx.doi.org/10.19101/IJATEE.2021.874108 Numerical analysis of double inlet two-stage inertance pulse tube cryocooler Mahmadrafik Choudhari1*, Bajirao Gawali2, Mohammedadil Momin3, Prateek Malwe1, Nandkishor Deshmukh1 and Rustam Dhalait1 Research Scholar, Walchand College of Engineering, Sangli-416415, India1 Professor, Walchand College of Engineering, Sangli-416415, India2 M.Tech Scholar, Walchand College of Engineering, Sangli-416415, India3 Received: 08-May-2021; Revised: 25-June-2021; Accepted: 27-June-2021 ©2021 Mahmadrafik Choudhari et al. This is an open access article distributed under the Creative Commons Attribution (CC BY) License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited. Abstract Stirling-type Pulse Tube Cryocoolers (PTC) are designed to meet present and upcoming commercial requirements and needs with durability and low vibrations. Multistaging in Stirling type PTC is one of the major developments reported in recent times for low-temperature achievement, due to improved performance over a period of time. The current study aims to define the methodology for numerical assessment of Double Inlet Two-Stage Pulse Tube Cryocooler (DITSPTC) to achieve cryogenic temperature of 20 K. This paper performs Computational Fluid Dynamics (CFD) simulation of PTC for defining the methodology using the CFD software package and then the same methodology is extended for the analysis of DITSPTC. The system simulations are performed with frequency of 70 Hz and average pressure of 20 bar. The minimum temperatures obtained from simulations are 95 K and 20 K at the first and second stage respectively.
    [Show full text]
  • Operation of Thermoacoustic Stirling Heat Engine Driven Large Multiple Pulse Tube Refrigerators
    LA-UR-04-2820, submitted to the proceedings of the 13th Int'l Cryocooler Conf. 1 Operation of Thermoacoustic Stirling Heat Engine Driven Large Multiple Pulse Tube Refrigerators Bayram Arman, John Wollan, and Vince Kotsubo Praxair, Inc. Tonawanda, NY 14150 Scott Backhaus and Greg Swift Los Alamos National Laboratory Los Alamos, NM 87545 ABSTRACT With support from Los Alamos National Laboratory, Praxair has been developing ther- moacoustic Stirling heat engines and refrigerators for liquefaction of natural gas. The combina- tion of thermoacoustic engines with pulse tube refrigerators is the only technology capable of producing significant cryogenic refrigeration with no moving parts. A prototype, powered by a natural-gas burner and with a projected natural-gas-liquefaction capacity of 500 gal/day, has been built and tested. The unit has liquefied 350 gal/day, with a projected production efficiency of 70% liquefaction and 30% combustion of an incoming gas stream. A larger system, intended to have a liquefaction capacity of 20,000 gal/day and an efficiency of 80 to 85% liquefaction, has undergone preliminary design. In the 500 gal/day system, the combustion-powered thermoacoustic Stirling heat engine drives three pulse tube refrigerators to generate refrigeration at methane liquefaction tempera- tures. Each refrigerator was designed to produce over 2 kW of refrigeration. The orifice valves of the three refrigerators were adjusted to eliminate Rayleigh streaming in the pulse tubes. This pa- per describes the hardware, operating experience, and some recent test results. INTRODUCTION Praxair has been developing thermoacoustic liquefiers and refrigerators for liquefaction of natural gas and for other cryogenic applications.
    [Show full text]
  • Comparison of a Novel Organic-Fluid Thermofluidic Heat Converter and an Organic Rankine Cycle Heat Engine§
    Article COMPARISON OF A NOVEL ORGANIC-FLUID THERMOFLUIDIC HEAT CONVERTER AND AN ORGANIC RANKINE CYCLE HEAT ENGINE§ Christoph J.W. Kirmse, Oyeniyi A. Oyewunmi, Andrew J. Haslam and Christos N. Markides* Clean Energy Processes (CEP) Laboratory, Department of Chemical Engineering, Imperial College London, South Kensington Campus, London SW7 2AZ, U.K. * Correspondence: [email protected]; Tel.: +44 (0)20 759 41601 § This paper is an extended version of our paper published in Proceedings of 3rd International Seminar on ORC Power Systems, Brussels, Belgium, 12–14 October 2015. Academic Editor: name Version May 27, 2016 submitted to Energies; Typeset by LATEX using class file mdpi.cls 1 Abstract: The Up-THERM heat converter is an unsteady, two-phase thermofluidic oscillator that 2 employs an organic working-fluid, which is currently being considered as a prime-mover in small- 3 to medium-scale combined heat and power (CHP) applications. In this paper, the Up-THERM heat 4 converter is compared to a basic (sub-critical, non-regenerative) equivalent organic Rankine cycle 5 (ORC) heat engine with respect to power output, thermal efficiency and exergy efficiency, but also 6 capital cost and specific cost. The study focuses on a pre-specified Up-THERM design in a selected 7 application, a heat-source temperature range from 210 °C to 500 °C and five different working 8 fluids (three n-alkanes and two refrigerants). A modelling methodology is developed that allows 9 the above technoeconomic performance indicators to be estimated for the two thermodynamic 10 power-generation systems. It is found that the power output of the ORC engine is generally higher 11 than that of the Up-THERM heat converter, at least as envisioned and in the chosen application, 12 as expected.
    [Show full text]
  • Analytical Model for the Refrigeration Power of the Orifice Pulse Tube Refrigerator
    UNITED STATES DEPARTMENT OF COMMERCE NATIONAL INSTITUTE OF STANDARDS AND TECHNOLOGY NisrNATL INST, OF STAND & TECH R.I.C. A111D3 MTflOtib NIST PUBLiCATiONS NIST Technical Note 1343 Analytical Model for the Refrigeration Power of the Orifice Pulse Tube Refrigerator Peter J. Storch Ray Radebaugh James E. Zimmerman Reservoir Volume Piston K/X//X/ Orifice Heat Exclianger Regenerator Pulse Tube 100 Heat Exchanger .U5753 #1343 1990 C.2 mo Analytical Model for the Refrigeration Power of the Orifice Pulse Tube Refrigerator Peter J. Storch Ray Radebaugh James E. Zimmerman Chemical Engineering Science Division Center for Chemical Technology National Measurement Laboratory National Institute of Standards and Technology Boulder, Colorado 80303-3328 Sponsored by NASA/Ames Research Center Moffett Field, California 94035 \. / U.S. DEPARTMENT OF COMMERCE, Robert A. Mosbacher, Secretary NATIONAL INSTITUTE OF STANDARDS AND TECHNOLOGY, John W. Lyons, Director Issued December 1990 National Institute of Standards and Technology Technical Note 1343 Natl. Inst. Stand. Technol., Tech. Note 1343, 94 pages (Dec. 1990) CODEN:NTNOEF U.S. GOVERNMENT PRINTING OFFICE WASHINGTON: 1990 For sale by the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402-9325 NOMENCLATURE PTR = pulse tube refrigerator BPTR = basic pulse tube refrigerator OPTR = orifice pulse tube refrigerator RPTR = resonant pulse tube refrigerator a = slope of average temperature profile Ag = gas cross—sectional area Cp = specific heat of gas f friction factor L length of
    [Show full text]
  • S O R P Tio N -C O O Le D M in Ia Tu R E D Ilu T Io N R E Fr Ig E R a to R S
    Sorption-cooled M iniature D ilution Refrigerators FOR AsTROPHYSICAL APPLICATIONS Gustav Teleberg A T h e s is s u b m it t e d t o C a r d if f U n iv e r sit y FOR THE DEGREE OF D o c t o r o f P h il o s o p h y S e p t e m b e r 2 0 0 6 UMI Number: U584881 All rights reserved INFORMATION TO ALL USERS The quality of this reproduction is dependent upon the quality of the copy submitted. In the unlikely event that the author did not send a complete manuscript and there are missing pages, these will be noted. Also, if material had to be removed, a note will indicate the deletion. Dissertation Publishing UMI U584881 Published by ProQuest LLC 2013. Copyright in the Dissertation held by the Author. Microform Edition © ProQuest LLC. All rights reserved. This work is protected against unauthorized copying under Title 17, United States Code. ProQuest LLC 789 East Eisenhower Parkway P.O. Box 1346 Ann Arbor, Ml 48106-1346 Author Gustav Teleberg Title: Sorption-cooled Miniature Dilution Refrigerators for Astrophysical Applications Date of submission: September 2006 Address: School of Physics & Astronomy Cardiff University 5 The Parade Cardiff, CF24 3YB Wales, UK Permission is granted to Cardiff University to circulate and to have copied for non-commercial purposes, at its discretion, the above tide upon the request of individuals or institutions. The author reserves other publication rights, and neither the thesis nor extensive extracts from it may be printed or otherwise reproduced without the authors written permission.
    [Show full text]
  • The Use of Sage Simulation Software in the Design and Testing
    THE USE OF SAGE SIMULATION SOFTWARE IN THE DESIGN AND TESTING OF SUNPOWER’S PULSE TUBE CRYOCOOLER A thesis presented to the faculty of the Fritz J. and Dolores H. Russ College of Engineering and Technology of Ohio University In partial fulfillment of the requirements for the degree Master of Science Kyle B. Wilson June 2005 This thesis entitled THE USE OF SAGE SIMULATION SOFTWARE IN THE DESIGN AND TESTING OF SUNPOWER’S PULSE TUBE CRYOCOOLER BY KYLE B. WILSON has been approved for the School of Mechanical Engineering and the Russ College of Engineering and Technology by Khairul Alam Moss Professor of Mechanical Engineering Dennis Irwin Dean, Fritz J. and Dolores H. Russ College of Engineering and Technology WILSON, KYLE B. MS. June 2005. Mechanical Engineering The Use of Sage Simulation Software in the Design and Testing of Sunpower’s Pulse Tube Cryocooler (130 pp.) Director of Thesis: Khairul Alam ABSTRACT This thesis discusses the development of a pulse tube cryocooler and the use of a software simulation tool called Sage in this effort. A pulse tube cryocooler is a type of refrigerator that operates in the cryogenic temperature range below 120 K (-153° C). The goal of this thesis spans from a basic understanding of the ideal thermodynamics of the pulse tube cryocooler (PTC) to a grasp of one commercial software package’s ability to model an actual, non-ideal PTC. The history and theory are discussed leading to the state-of-the-art technology. The focus then turns to the specific development efforts of the author at his place of employment, Sunpower, Inc.
    [Show full text]