DOCSLIB.ORG

Nondestructive Testing (NDT) and Sensor Technology for Service Life Modeling of New and Existing Concrete Structures

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Nondestructive Testing (NDT) and Sensor Technology for Service Life Modeling of New and Existing Concrete Structures NISTIR 7974 Nondestructive Testing (NDT) and Sensor Technology for Service Life Modeling of New and Existing Concrete Structures Kenneth A. Snyder Li-Piin Sung Geraldine S. Cheok This publication is available free of charge from: https://doi.org/10.6028/NIST.IR.7974 NISTIR 7974 Nondestructive Testing (NDT) and Sensor Technology for Service Life Modeling of New and Existing Concrete Structures Kenneth A. Snyder Li-Piin Sung Materials and Structural Systems Division Engineering Laboratory Geraldine S. Cheok Intelligent Systems Division Engineering Laboratory December 2013 U.S. Department of Commerce Penny Pritzker, Secretary National Institute of Standards and Technology Patrick D. Gallagher, Under Secretary of Commerce for Standards and Technology and Director ii ABSTRACT Nondestructive test (NDT) methods and sensor technologies are evaluated in the context of providing input parameters to service life prediction models for reinforced concrete structures. Relevant NDT methods and sensors are identified that are based on diverse technologies including mechanical impact, ultrasonic waves, electromagnetic waves, nuclear, and chemical and electrical methods. The degradation scenarios of reinforcement corrosion, alkali-silica reaction, and cracking are used to identify gaps in available NDT methods for supporting condition assessment and service life prediction. Common gaps are identified, along with strategies for resolving those gaps. iii Disclaimer: Certain commercial products are identified in this paper to specify the materials used and procedures employed. In no case does such identification imply endorsement or recommendation by the National Institute of Standards and Technology, nor does it indicate that the products are necessarily the best available for the purpose. iv TABLE OF CONTENTS ABSTRACT ............................................................................................................................................................................... I EXECUTIVE SUMMARY .................................................................................................................................................... VII LIST OF FIGURES .................................................................................................................................................................. X LIST OF TABLES .................................................................................................................................................................. XI ABBREVIATIONS ............................................................................................................................................................... XII 1 INTRODUCTION ............................................................................................................................................................. 1 2 STRUCTURAL CONCRETE IN THE NUCLEAR INFRASTRUCTURE ................................................................... 2 3 MODELING SERVICE LIFE ........................................................................................................................................... 3 3.1 EMPIRICAL VS. PHYSICOCHEMICAL MODELS ............................................................................................................................... 4 3.2 CONCEPTUAL SERVICE L IFE MODEL ............................................................................................................................................. 5 4 MEASUREMENT METHODOLOGIES ......................................................................................................................... 7 5 NDT TECHNOLOGIES ................................................................................................................................................... 8 5.1 ELECTRO-MECHANICAL STRAIN GAUGES .................................................................................................................................... 8 5.2 ACOUSTIC / MECHANICAL IMPACT ............................................................................................................................................... 8 5.3 ELECTROMAGNETIC ......................................................................................................................................................................... 8 5.4 NUCLEAR ............................................................................................................................................................................................ 8 5.5 ELECTRICAL / CHEMICAL ................................................................................................................................................................ 8 5.6 MASS TRANSPORT ............................................................................................................................................................................ 9 5.7 EXISTING I N-DEPTH SUMMARIES .................................................................................................................................................. 9 5.8 COMMERCIAL DEVICES .................................................................................................................................................................... 9 6 ELECTRO-MECHANICAL STRAIN GAUGES .......................................................................................................... 10 6.1 MECHANICAL GAUGES .................................................................................................................................................................. 10 6.2 PIEZO-ELECTRIC G AUGES ............................................................................................................................................................ 11 7 MECHANICAL / ACOUSTIC METHODS ................................................................................................................. 12 7.1 REBOUND METHOD ....................................................................................................................................................................... 12 7.2 PENETRATION RESISTANCE ........................................................................................................................................................ 14 7.3 PULLOUT TEST ............................................................................................................................................................................... 15 7.4 BREAK-OFF T EST .......................................................................................................................................................................... 17 7.5 RESONANT F REQUENCY METHODS ............................................................................................................................................ 19 7.6 ACOUSTIC W AVE METHODS ........................................................................................................................................................ 20 7.7 ULTRASONIC P ULSE VELOCITY (UPV) ...................................................................................................................................... 21 7.8 ULTRASONIC P ULSE-ECHO (UPE) ............................................................................................................................................. 23 7.9 IMPACT-ECHO (IE) ....................................................................................................................................................................... 25 7.10 SPECTRAL ANALYSIS OF SURFACE WAVES ............................................................................................................................ 27 7.11 NONLINEAR ULTRASONIC A NALYSIS ...................................................................................................................................... 28 7.12 ACOUSTIC E MISSION .................................................................................................................................................................. 30 7.13 ULTRASONIC P HASED A RRAYS / ULTRASONIC P HASE SPECTROSCOPY ........................................................................... 32 7.14 NON-CONTACT ULTRASOUND .................................................................................................................................................. 34 8 ELECTROMAGNETIC METHODS ............................................................................................................................ 35 8.1 TIME-DOMAIN R EFLECTOMETRY ............................................................................................................................................... 35 8.2 INFRARED T HERMOGRAPHY ........................................................................................................................................................ 36 8.3 GAMMA R AY/X-RAY RADIOGRAPHIC TESTING ....................................................................................................................... 37 8.4 GROUND-PENETRATING R ADAR (GPR) ................................................................................................................................... 38 8.5 EDDY CURRENT / PULSE INDUCTION ........................................................................................................................................ 40 v 8.6 LASER S HEAROGRAPHY ...............................................................................................................................................................
Load more

Recommended publications
  • Nondestructive Methods to Characterize Rock Mechanical Properties at Low-Temperature: Applications for Asteroid Capture Technologies
    Graduate Theses, Dissertations, and Problem Reports 2016 Nondestructive Methods to Characterize Rock Mechanical Properties at Low-Temperature: Applications for Asteroid Capture Technologies Kara A. Savage Follow this and additional works at: https://researchrepository.wvu.edu/etd Recommended Citation Savage, Kara A., "Nondestructive Methods to Characterize Rock Mechanical Properties at Low- Temperature: Applications for Asteroid Capture Technologies" (2016). Graduate Theses, Dissertations, and Problem Reports. 6573. https://researchrepository.wvu.edu/etd/6573 This Thesis is protected by copyright and/or related rights. It has been brought to you by the The Research Repository @ WVU with permission from the rights-holder(s). You are free to use this Thesis in any way that is permitted by the copyright and related rights legislation that applies to your use. For other uses you must obtain permission from the rights-holder(s) directly, unless additional rights are indicated by a Creative Commons license in the record and/ or on the work itself. This Thesis has been accepted for inclusion in WVU Graduate Theses, Dissertations, and Problem Reports collection by an authorized administrator of The Research Repository @ WVU. For more information, please contact [email protected]. Nondestructive Methods to Characterize Rock Mechanical Properties at Low-Temperature: Applications for Asteroid Capture Technologies Kara A. Savage Thesis Submitted to the Statler College of Engineering at West Virginia University in partial fulfillment of the requirements for the degree of Master of Science in Mining Engineering Aaron Noble, Ph.D., Chair Brijes Mishra, Ph.D. Thomas Evans, Ph.D. Department of Mining Engineering Morgantown, West Virginia 2016 Keywords: Nondestructive Tests, Low-Temperature Rock Mechanics, Schmidt Rebound Hammer, Ultrasonic Pulse Velocity, Asteroid Capture Copyright 2016 Kara A.
    [Show full text]
  • Use of Components Analysis to Identify Internal Heat in Breast Dynamic Thermal Images
    IEEE TRANSACTIONS ON MEDICAL IMAGING, VOL. xx, NO. X, NOVEMBER 2020 1 Use of components analysis to identify internal heat in breast dynamic thermal images Meir Gershenson Abstract — I suggest a method for biomedical imaging new ones. This process is called angiogenesis. The increase of with heat using principal and independent components blood flow at the cancerous site is associated with an increase analysis. This method produces novel results suggesting in the tissue’s ability to absorb heat. The bio heat transfer physiologic mechanisms. When using thermal imaging to equation describing thermal propagation is given by1 detect breast cancer, the dominant heat signature is of indirect heat transported by the blood away from the tumor i ͟ʚÈʛ ͎ʚr, ͨʛ Ǝ ̽ ∙ ͎ʚÈ, ͨʛ Ǝ͖͋ƍ͋͡ Ɣ 0 location into the skin. Interpretation is usually based on i/ vascular patterns and not by observing the direct ͖͋ Ɣ !͖̽ ʞ͎ʚr, ͨʛ Ǝ ͎ͤʚr, ͨʛʟ (1) cancerous heat. In this new method one uses a sequence of thermal images of the patient’s breast following external Typical values are taken from Azarnoosh J et al. 2 and are temperature change. Data are recorded and analyzed using independent component analysis (ICA) and principal given in Table 1. From the above table the increase in blood component analysis (PCA). ICA separates the image TABLE I sequence into new independent images having a common THRMOPHYSICAL PARAMETERS OF TYPICAL BREAST characteristic time behavior. Using the Brazilian visual lab Density Specific Thermal ωb Qm mastology data set, I observed three types of component heat C conductivity (s-1) *10 -3 (W/m3) images: Images corresponding to a minimum change as a (kg/m3) (J/kg K) ͟ (W/m) function of applied temperature or time, which suggests an Gland 1020 3060 0.322 0.34 – 1.7 700 association with the cancer generated heat, images in which a moderate temperature dependence is associated Tumor 1020 3060 0.564 6 - 16 7792 with veins affected by vasomodulation, and images of Blood 1060 3840 complex time behavior indicating heat absorption due to .
    [Show full text]
  • Guidelines for Pressure Vessel Safety Assessment
    11^^^^ United States Department of Commerce National Institute of Standards and Tectinology NIST Special Publication 780 Guidelines for Pressure Vessel Safety Assessment Sumio Yukawa NATIONAL INSTITUTE OF STANDARDS & TECHNOLOGY Research Information Center Gaithersburg, MD 20899 DATE DUE Demco. Inc. 38-293 NIST Special Publication 780 Guidelines for Pressure Vessel Safety Assessment Sumio Yukawa Materials Reliability Division Materials Science and Engineering Laboratory National Institute of Standards and Technology Boulder, CO 80303 Sponsored by Occupational Safety and Health Administration U.S. Department of Labor Washington, DC 20210 Issued April 1990 U.S. Department of Commerce Robert A. Mosbacher, Secretary National Institute of Standards and Technology John W. Lyons, Director National Institute of Standards U.S. Government Printing Office For sale by the Superintendent and Technology Washington: 1990 of Documents Special Publication 780 U.S. Government Printing Office Natl. Inst. Stand. Technol. Washington, DC 20402 Spec. Publ. 780 75 pages (Apr. 1990) CODEN: NSPUE2 CONTENTS Page ABSTRACT vii 1. INTRODUCTION 1 2. SCOPE AND GENERAL INFORMATION 1 2 . 1 Scope 1 2.2 General Considerations 3 3. PRESSURE VESSEL DESIGN 4 3.1 ASME Code 4 3.1.1 Section VIII of ASME Code 5 3.1.2 Scope of Section VIII 5 3.1.3 Summary of Design Rules and Margins 6 3.1.4 Implementation of ASME Code 9 3.2 API Standard 620 10 3.2.1 Scope of API 620 12 3.2.2 Design Rules 12 3.2.3 Implementation of API 620 12 3.3. Remarks on Design Codes 14 4. DETERIORATION AND FAILURE MODES 14 4.1 Preexisting Causes 14 4.1.1 Design and Construction Related Deficiencies.
    [Show full text]
  • Human Factors in Non-Destructive Testing (NDT): Risks and Challenges of Mechanised NDT
    Dipl.-Psych. Marija Bertović Human Factors in Non-Destructive Testing (NDT): Risks and Challenges of Mechanised NDT BAM-Dissertationsreihe • Band 145 Berlin 2016 Die vorliegende Arbeit entstand an der Bundesanstalt für Materialforschung und -prüfung (BAM). Impressum Human Factors in Non-Destructive Testing (NDT): Risks and Challenges of Mechanised NDT 2016 Herausgeber: Bundesanstalt für Materialforschung und -prüfung (BAM) Unter den Eichen 87 12205 Berlin Telefon: +49 30 8104-0 Telefax: +49 30 8104-72222 E-Mail: [email protected] Internet: www.bam.de Copyright© 2016 by Bundesanstalt für Materialforschung und -prüfung (BAM) Layout: BAM-Referat Z.8 ISSN 1613-4249 ISBN 978-3-9817502-7-0 Human Factors in Non-Destructive Testing (NDT): Risks and Challenges of Mechanised NDT Vorgelegt von Dipl. -Psych. Marija Bertovic geb. in Ogulin, Kroatien von der Fakultät V – Verkehrs- und Maschinensysteme der Technischen Universität Berlin zur Erlangung des akademischen Grades Doktorin der Philosophie -Dr. phil.- genehmigte Dissertation Promotionsausschuss: Vorsitzender: Prof. Dr. phil. Manfred Thüring Gutachter: Prof. Dr. phil. Dietrich Manzey Gutachter: Dr. rer. nat. et Ing. habil. Gerd-Rüdiger Jaenisch Tag der wissenschaftlichen Aussprache: 1 September 2015 Berlin 2015 D83 Abstract Non-destructive testing (NDT) is regarded as one of the key elements in ensuring quality of engineering systems and their safe use. A failure of NDT to detect critical defects in safety- relevant components, such as those in the nuclear industry, may lead to catastrophic consequences for the environment and the people. Therefore, ensuring that NDT methods are capable of detecting all critical defects, i.e. that they are reliable, is of utmost importance. Reliability of NDT is affected by human factors, which have thus far received the least amount of attention in the reliability assessments.
    [Show full text]
  • Methods for Nondestructive Testing of Urban Trees
    Review Methods for Nondestructive Testing of Urban Trees Richard Bruce Allison 1,2,*, Xiping Wang 3,* and Christopher A. Senalik 3 1 Department of Forest and Wildlife Ecology, University of Wisconsin, Madison, WI 53706, USA 2 Allison Tree Care, LLC, Verona, WI 53593, USA 3 USDA Forest Service, Forest Products Laboratory, Madison, WI 53726-2398, USA; [email protected] * Correspondence: [email protected] (R.B.A); [email protected] (X.W.); Tel.: +1-608-848-2345 (R.B.A); +1-608-231-9461 (X.W.) Received: 21 September 2020; Accepted: 30 October 2020; Published: 16 December 2020 Abstract: Researchers have developed various methods and tools for nondestructively testing urban trees for decay and stability. A general review of these methods includes simple visual inspection, acoustic measuring devices, microdrills, pull testing, ground penetrating radar, x-ray scanning, remote sensing, electrical resistivity tomography and infra-red thermography. Along with these testing methods have come support literature to interpret the data. Keywords: decay; defect; hazard assessment; inspection; nondestructive testing; urban trees 1. Introduction Trees within an urban community provide significant ecological, economic and social benefits, making a city more livable and comfortable for its inhabitants [1]. However, as large physical wooden structures in close proximity to dense populations of people and property, tree failure can cause harm. Urban forest managers use biological and engineering principles to determine a tree’s structural soundness and estimate the probability of failure. Nondestructive testing (NDT) methods by locating and quantifying wood decay and defect are used to measure the physical condition of trees within the urban forest to promote public safety and property protection.
    [Show full text]
  • Non-Destructive Testing for Plant Life Assessment
    Non-destructive testing for plant life assessment TRAINING COURSE SERIES VIENNA, 2005 26 TRAINING COURSE SERIES No. 26 Non-destructive testing for plant life assessment INTERNATIONAL ATOMIC ENERGY AGENCY, VIENNA, 2005 The originating Section of this publication in the IAEA was: Industrial Applications and Chemistry Section International Atomic Energy Agency Wagramer Strasse 5 P.O. Box 100 A-1400 Vienna, Austria NON-DESTRUCTIVE TESTING FOR PLANT LIFE ASSESSMENT IAEA, VIENNA, 2005 IAEA-TCS-26 ISSN 1018–5518 © IAEA, 2005 Printed by the IAEA in Austria August 2005 FOREWORD The International Atomic Energy Agency (IAEA) is promoting industrial applications of non- destructive testing (NDT) technology, which includes radiography testing (RT) and related methods, to assure safety and reliability of operation of industrial facilities and processes. NDT technology is essentially needed for improvement of the quality of industrial products, safe performance of equipment and plants, including safety of metallic and concrete structures and constructions. The IAEA is playing an important role in promoting the NDT use and technology support to Member States, in harmonisation for training and certification of NDT personnel, and in establishing national accreditation and certifying bodies. All these efforts have led to a stage of maturity and self sufficiency in numerous countries especially in the field of training and certification of personnel, and in provision of services to industries. This has had a positive impact on the improvement of the quality of industrial goods and services. NDT methods are primarily used for detection, location and sizing of surface and internal defects (in welds, castings, forging, composite materials, concrete and many more).
    [Show full text]
  • Nondestructive Testing with 3MA—An Overview of Principles and Applications
    applied sciences Article Nondestructive Testing with 3MA—An Overview of Principles and Applications Bernd Wolter *, Yasmine Gabi and Christian Conrad Fraunhofer Institute for Nondestructive Testing IZFP, Campus E3 1, 66123 Saarbrücken, Germany; [email protected] (Y.G.); [email protected] (C.C.) * Correspondence: [email protected]; Tel.: +49-681-9302-3883 Received: 1 February 2019; Accepted: 8 March 2019; Published: 14 March 2019 Abstract: More than three decades ago, at Fraunhofer IZFP, research activities that were related to the application of micromagnetic methods for nondestructive testing (NDT) of the microstructure and the properties of ferrous materials commenced. Soon, it was observed that it is beneficial to combine the measuring information from several micromagnetic methods and measuring parameters. This was the birth of 3MA—the micromagnetic multi-parametric microstructure and stress analysis. Since then, 3MA has undergone a remarkable development. It has proven to be one of the most valuable testing techniques for the nondestructive characterization of metallic materials. Nowadays, 3MA is well accepted in industrial production and material research. Over the years, several equipment variants and a wide range of probe heads have been developed, ranging from magnetic microscopes with µm resolution up to large inspection systems for in-line strip steel inspection. 3MA is extremely versatile, as proved by a huge amount of reported applications, such as the quantitative determination of hardness, hardening depth, residual stress, and other material parameters. Today, specialized 3MA systems are available for manual or automated testing of various materials, semi-finished goods, and final products that are made of steel, cast iron, or other ferromagnetic materials.
    [Show full text]
  • Observations on the Application of Smart Pigging on Transmission Pipelines
    Observations on the Application of Smart Pigging on Transmission Pipelines A Focus on OPS’s Inline Inspection Public Meeting of 8/11/05 Prepared for the http://www.pstrust.org/ by Richard B. Kuprewicz President, Accufacts Inc. [email protected] September 5, 2005 Accufacts Inc. “Clear Knowledge in the Over Information Age” This report is developed from information clearly in the public domain. The views expressed in this document represent the observations and opinions of the author. Executive Summary Smart pigs, also known as inline inspection (“ILI”) tools or intelligent pigs, are electronic devices designed to flow on the inside of a transmission pipeline, usually while the line is in service, to inspect a pipeline for various types of anomalies that can increase the risks of pipeline failure.1 This paper comments on observations pertaining to the Office of Pipeline Safety’s (“OPS”) public meeting of August 11, 2005 in Houston, Texas.2 Approximately 400 industry, pigging vendors, and regulatory representatives attended this meeting, dramatically underscoring the gravity of this important subject. This author concurs with the public meeting announcement and fully supports and is committed to assisting OPS’s effort, and many in the industry, to advance the prudent application of ILI in gas and liquid transmission pipeline systems. OPS has a long history of encouraging technical development to improve pipeline safety. Smart pigging has taken on an even more critical role with the promulgation of integrity management rulemaking in the last several years.3 In some situations pigging is not the best or preferred inspection method for various reasons, especially if the technology is misapplied, oversold, or the pigging process and information mishandled.
    [Show full text]
  • Ac 25-29 9/20/13
    U.S. Department Advisory of Transportation Federal Aviation Administration Circular Subject: Development of a Nondestructive Date: 9/20/13 AC No: 25-29 Inspection Program/Organization Initiated by: AFS-300 Change: 1. PURPOSE. This advisory circular (AC) provides guidance for the development of organizations and facilities performing nondestructive inspections (NDI). This material is neither mandatory nor regulatory in nature and does not constitute a regulation. It describes an acceptable means, but not the only means, for developing NDI facilities, as well as organizational and quality manuals. We, the Federal Aviation Administration (FAA), will consider other methods of demonstrating compliance that you may elect to present. We use the terms “must” and “will” in this AC only to ensure you correctly apply the recommendations of this particular method of compliance, if you choose to do so. 2. RELATED CFR REGULATIONS AND REFERENCES. See Appendix 1. 3. DEFINITIONS. a. Certification. Written testimony of qualification. The employer issues a certification as a written statement (which may be in an electronic format) that an individual has met the requirements of an accepted standard. b. Documentation. Written or printed record furnishing information or evidence; a legal or official record in paper or electronic form. c. Experience. Actual performance or observation conducted in the work environment that results in acquiring knowledge and skills. Although experience is not obtained during classroom or laboratory training, it does include on-the-job training (OJT). d. Method. One of the disciplines of NDIs or testing (e.g., radiography, ultrasonic, etc.). Each method consists of its own different techniques. e. On-the-Job Training (OJT).
    [Show full text]
  • Eddy Current Nondestructive Testing NATIONAL BUREAU of STANDARDS
    A 11 10 3 073222 TECH HAG. NATL INST OF STANDARDS! » fe* 1 All 103073222 to NBS SPECIAL PUBLICATION 589 U.S. DEPARTMENT OF COMMERCE / National Bureau of Standards Eddy Current Nondestructive Testing NATIONAL BUREAU OF STANDARDS The National Bureau of Standards' was established by an act ot Congress on March 3, 1901. The Bureau's overall goal is to strengthen and advance the Nation's science and technology and facilitate their effective application for public benefit. To this end, the Bureau conducts research and provides: (1) a basis for the Nation's physical measurement system, (2) scientific and technological services for industry and government, (3) a technical basis for equity in trade, and (4) technical services to promote public safety. The Bureau's technical work is per- formed by the National Measurement Laboratory, the National Engineering Laboratory, and the Institute for Computer Sciences and Technology. THE NATIONAL MEASUREMENT LABORATORY provides the national system of physical and chemical and materials measurement; coordinates the system with measurement systems of other nations and furnishes essential services leading to accurate and uniform physical and chemical measurement throughout the Nation's scientific community, industry, and commerce; conducts materials research leading to improved methods of measurement, standards, and data on the properties of materials needed by industry, commerce, educational institutions, and Government; provides advisory and research services to other Government agencies; develops, produces,
    [Show full text]
  • The Division of Extended Learning 2017 Catalog Nu.Edu/El
    THE DIVISION OF EXTENDED LEARNING 2017 CATALOG NU.EDU/EL A Private Nonprofi t University Serving the Public Good™ 2 WWW.NU.EDU/EL | 800.628.8648 EXT 8600 Welcome September 14, 2016 Dear Students, In the pursuit of life-long learning, the Division of Extended Learning at National University offers professional development and personal enrichment courses in a variety of subjects including business, leadership, marketing, education, human resources and many more. Most can be taken completely online so you don’t have to leave the comforts of home as you manage work and family. If you’re working full-time, check with your employer on your company’s tuition reimbursement plan. This is a great way to fund your education while learning a valuable skill that can strengthen your value to your employer and broaden your career options. Do something for yourself by expanding your professional development, pursuing a special interest, or acquiring a new skill. Most courses provide continuing education units (CEUs) of credit that you may need to stay relevant in your industry. To speak with a student advisor, please call (800) 628-8648 x8600 or email us at [email protected]. Sincerely, Roxanne J. Kymaani, PhD Executive Director The Division of Extended Learning National University Table of Contents SCHOOL OF PROFESSIONAL STUDIES PROGRAMS OFFERED IN DIVISION OF EXTENDED LEARNING ............................................... 2 DIVISION OF EXTENDED LEARNING 3678 Aero Court, Suite 236 San Diego, CA 92123 ACADEMIC TUITION RATES ............................................................. 4 [email protected] www.nu.edu/el GENERAL INFORMATION ................................................................. 3 Phone: 800.628.8648 ext. 8600 Mission Statement .................................................................... 3 Fax: 619.563.7309 About Division of Extended Learning ......................................
    [Show full text]
  • Introduction to Nondestructive Testing Ultrasonic Testing (UT) UT Uses the Same Principle As Is Used in Naval SONAR and Fish Finders
    Introduction to Nondestructive Testing Introduction to Nondestructive Testing What is nondestructive testing? NonDestructive Testing (NDT) is the process of doing inspections, testing, or evaluating materials, components or assemblies for defects without destroying the material or component. Or the use of noninvasive techniques to determine the integrity of a material, component or structure”. In other words, “Inspect or measure without doing harm.” Introduction to Nondestructive Testing Who Uses NDT? • NDT plays a vital role in assuring the safe operation of equipment and systems • Industries that utilize NDT: – Airline and Aerospace – Automotive and Railroad – Construction – Hydroelectric, Fossil, and Nuclear Power – Textile and Manufacturing – Chemical and Petrochemical – Logistics and Supply – Medical and Pharmaceutical Introduction to Nondestructive Testing What are Some Uses of NDT? • Flaw Detection and Evaluation - the size, shape, or orientation of a flaw (such as a crack or porosity) • Leak Detection • Location Determination • Dimensional Measurements • Structure and Microstructure Characterization • Estimation of Mechanical and Physical Properties • Stress (Strain) and Dynamic Response Measurements • Material Sorting and Chemical Composition Determination • the thickness of a material or coating • the hardness of a material • a material’s electrical conductivity Introduction to Nondestructive Testing When is NDT Used? There are NDT application at almost any stage in the production or life cycle of a component. – To assist in
    [Show full text]