10 CAN SEAMER INSTRUCTIONS (For Gering Portable Seamer)

Total Page：16

File Type：pdf, Size：1020Kb

#10 CAN SEAMER INSTRUCTIONS (For Gering Portable Seamer) Setting Up 1. Fasten seamer securely to table using “C” clamps. 2. Verify base height setting: a. Place a lid on an empty can and place the can on the round baseplate. b. Raise the can to upper locked position by lifting up on the base clamp handle. c. If the base clamp handle does not snap firmly into upper, locked position, loosen the lock nut, adjust the spindle height, and retighten the lock nut. d. Lower base and remove empty can. 3. Plug in seamer. 4. Cut open top of bag containing oxygen absorbers. Remove only enough packets for the next 20 to 30 minutes. Reseal bag with the special clamp provided. Reopen and reseal bag as additional absorbers are needed. Filling Cans 1. Fill can to within ¼ inch of top of can. 2. Place an oxygen absorber packet in the top of can. 3. Label the lid or can to identify the product. 4. Place a lid on the can. Seaming Cans 1. Place the filled can onto the sealer base and raise to upper locked position. 2. Turn on motor by pushing in and holding the switch, using the left hand thumb. 3. PUSH roll lever slowly in to fully engage 1st operation roll. 4. Hold firmly in place for 3 revolutions. 5. PULL roll lever to fully engaged 2nd operation roll position. 6. Hold firmly in place for 3 revolutions. 7. Release motor switch to turn off motor, lower base, and remove can. Inspecting Seam 1. Visually inspect the completed seam to see that it is the same as the factory seamed end. a. If the seam has droops, make certain that the 1st operation roll is fully engaged on the next can. b. If the seam has not been flattened adequately, hold more pressure in the 2nd operation. CAUTION: Keep children away from this machine while operating. 28 April 2005 Copyright © 2005 Brigham Young University, Women's Conference. All Rights Reserved. .

Copy Link

Recommended publications

Food Packaging Technology
FOOD PACKAGING TECHNOLOGY Edited by RICHARD COLES Consultant in Food Packaging, London DEREK MCDOWELL Head of Supply and Packaging Division Loughry College, Northern Ireland and MARK J. KIRWAN Consultant in Packaging Technology London Blackwell Publishing © 2003 by Blackwell Publishing Ltd Trademark Notice: Product or corporate names may be trademarks or registered Editorial Offices: trademarks, and are used only for identification 9600 Garsington Road, Oxford OX4 2DQ and explanation, without intent to infringe. Tel: +44 (0) 1865 776868 108 Cowley Road, Oxford OX4 1JF, UK First published 2003 Tel: +44 (0) 1865 791100 Blackwell Munksgaard, 1 Rosenørns Allè, Library of Congress Cataloging in P.O. Box 227, DK-1502 Copenhagen V, Publication Data Denmark A catalog record for this title is available Tel: +45 77 33 33 33 from the Library of Congress Blackwell Publishing Asia Pty Ltd, 550 Swanston Street, Carlton South, British Library Cataloguing in Victoria 3053, Australia Publication Data Tel: +61 (0)3 9347 0300 A catalogue record for this title is available Blackwell Publishing, 10 rue Casimir from the British Library Delavigne, 75006 Paris, France ISBN 1–84127–221–3 Tel: +33 1 53 10 33 10 Originated as Sheffield Academic Press Published in the USA and Canada (only) by Set in 10.5/12pt Times CRC Press LLC by Integra Software Services Pvt Ltd, 2000 Corporate Blvd., N.W. Pondicherry, India Boca Raton, FL 33431, USA Printed and bound in Great Britain, Orders from the USA and Canada (only) to using acid-free paper by CRC Press LLC MPG Books Ltd, Bodmin, Cornwall USA and Canada only: For further information on ISBN 0–8493–9788–X Blackwell Publishing, visit our website: The right of the Author to be identified as the www.blackwellpublishing.com Author of this Work has been asserted in accordance with the Copyright, Designs and Patents Act 1988.
[Show full text]
Semi-Automatic Bottling Systems for Wine
Semi NEW! Semi Automatic Automatic Automatic Bottling Systems Rinser / Filler / Bottling for sparkling Seamer for still Systems for wine in and sparkling still wine bottles products in cans Semi-Automatic Automatic Rinser / Filler / Rinser / Filler / Inline Seamer for still Corker / Capper Carbonators and sparkling for still wine and products in sparkling cans wine Capsuling Mushroom Machines Automatic Corkers & Wire Semi-Automatic Labelers hood cage and Automatic applicators IC Filling Systems Inc. Santa Rosa, California, USA Est. 1994 r e p p a C PP S O em R i Automatic r e g a C & Mu ker shroom Cor r e ill F 4 um Valve Vacu SEMI-AUTOMATIC BOTTLING SYSTEMS FOR WINE r le e b La S ic emi Automat r nse Bottle Ri d ea H r RO ng le PP Cappi su ap Be C C nch Top PV SEMI-AUTOMATIC RINSER FILLER CAPPER FOR SPARKLING WINES O S I C F R 1 6 6 ic at RO tom PP Semi Au AUTOMATIC RINSER FILLER SEAMER FOR CANS FOR STILL OR SPARKLING PRODUCTS 1,500 CPH OUTPUT VIEW IN ACTION AT Can Seamer 661 EPV Can Rinser S e m i A u t o https://icfs.to/canu m a t ic R 661 EPV OP P Capper Can 661 EPV Rinser and Filler Filler Can End Distribution Unit SEMI-AUTOMATIC RINSER FILLER SEAMER FOR CANS FOR STILL OR SPARKLING PRODUCTS UP TO 500 CPH OUTPUT M u s h r S o S A C e e o u a m m t n m o i i - m S C A A e o u r u a a t e t ti m r o ll o c e k m i m C r er a F at a D & tic r & ic er n eta C Can Rinse Can Seam Loading il ager AUTOMATIC RINSER CARBONATORS FILLER CORKER FOR STILL WINE OUTPUT 1,500 BPH A I n u l i t n o e m C a a ti rb c o R n in r ato se rke ICFILLINGSYSTEMS.COM r r Filler Co ABOUT IC FILLING SYSTEMS INC.
[Show full text]
Union Standard Catalog
25,000 MODERN USED & REBUILT PROCESSING & PACKAGING MACHINES EQUIPMENT VISIT OUR NEW WEB SITE www.unionmachinery.com Our Huge Inventory is now on the Web with Descriptions and Photos. NEW YORK CHICAGO MEXICO TEL: 718-585-0200 • FAX: 718-993-2650 TEL: 773-376-5400 • FAX: 773-376-0634 TEL: 5-300-3033 • FAX: 5-301-2934 801 E. 141 ST., 4248 W. 47 ST., SAN LUIS TLATILCO 6-A, COL SAN LUIS TLATILCO UNION STANDARD UNION STANDARD BRONX., NY 10454 CHICAGO, IL 60632 NAUCALPAN, EDO. DE MEXICO C.P. 53370 E-mail: [email protected] Internet: www.unionmachinery.com UNION STANDARD EQUIPMENT COMPANY UNION CONFECTIONERY MACHINERY COMPANY DIV. OF NATIONAL EQUIPMENT CORP. USED & LITY REBU UA IL Q T WORLD'S LARGEST DEALERS OF 801-825 East 141st Street Bronx, New York 10454-1917 MODERN RECONDITIONED PACKAGING & PROCESSING MACHINERY Tel: (718) 585-0200 • Fax: (718) 993-2650 E-mail: [email protected] ES 12 TABLISHED 19 WE ARE IN THE BEST POSITION EVER TO MEET YOUR MACHINERY NEEDS Established in 1912, four generations of the Greenberg family have established Union Standard and Union Confectionery as the world's largest suppliers of processing and packaging equipment with more than 25,000 machines in our New York, Chicago, Mexico D.F. and London facilities. There has never been a better time to contact us for buying and selling machinery. WE OFFER: THE WORLD'S LARGEST INVENTORY More than 25,000 processing and packaging machines in stock and available for your inspection MODERN USED & RECONDITIONED EQUIPMENT Late style equipment which can be reconditioned and set to your specifications.
[Show full text]
Liquids Filling and Packaging
pg_0001 Page 1 of 3 home .cd3wd .ar .cn .de .en .es .fr .id .it .ph .po .ru .sw LIQUIDS FILLING AND PACKAGING Liquids can be either thin (eg oils, milk, syrups and juices) or thick and viscous (eg sauces, pickles, hot jams and confectionery). The type of filler used is different for each group of liquids . The packaging requirements of different liquids are similar in that the liquid must be contained but they differ according to whether the liquid is spoiled by air, light, bacteria etc. Filling Low viscosity (thin) liquids The simplest filler is a jug but this is often too slow for small businesses. A simple filler can be made by fitting one or more taps to the base of a bucket, see Figure 1. The bucket should be stainless steel for hot acid liquids (eg fruit juices) or food grade plastic for cold filling. Iron and copper should not generally be used in food handling. A more sophisticated system in which the volume of liquid filled into file:///D:/cd3wddvd/NoExe/Master/dvd001/dvd1/ITDG/LIQPACK/EN/pg_0001.htm 08/ 11/ 2011 pg_0001 Page 2 of 3 volume of liquid filled into iseach controlled, container is obtained using a piston filler, see Figure 2. This is made from glass or the materials described above. Viscous liquids Because these liquids do not flow easily, the piston filler is the preferred option. Liquids that contain particles Both low and high viscosity liquids may contain particles of food (eg fruit, puips, sauces and pickles). The fillers described above will tend to become blocked by particles and a simple filler made from a stainless steel or plastic funnel is more suitable, Figure 3.
[Show full text]
OMVE FS210 & FS211 Clean-Fill
® FS210 & FS211 Clean-Fill Hygienic Filling & Closing Bench When hygienic filling is your priority There are still many laboratories and pilot plants that fill and close the heat-treated product in an open contaminated atmosphere. Moreover the filling line has not been part of a CIP and/or SIP procedure. This will create unacceptable variations in the quality of your trials and doesn’t give a representative simulation of an industrial process line. With the special designed Clean-Fill & Clean-Fill ESL ,OMVE offers the widest range of filling benches for laboratories and pilot plants within the food industry. Different packaging can be filled and closed within the hygienic environment. Two types of hygienic fillers: 1. FS210: The Clean-Fill Basic is a filler in stainless steel with a filling point. A foot pedal for filling the containers is controlled by an automatic hygienic valve. A hygienic closed loop during cleaning is standard. 2. FS211: The Clean-Fill ESL (Extended Shelf Life) regroups all features of the Clean-Fill Basic but also includes a temperature sensor at the coldest spot as well as a touch screen to display this temperature during sterilization. The condensate cooler ensures controllable cooling of the pressurized water or steam during sterilization Unique Features F FS210 FS211 illing Sterile Down flow filling bench Adjustable front window Minimum height of the unit, no need for dissembling S Complete Stainless Steel system ystems Integrated in cleaning loop Aseptic control valves Larger versions (‘’Extended’’) available Different closing devices can be installed Integrated in sterilization loop TFT touch screen guidance during sterilization Working principle FS The OMVE Clean-Fill creates a class 100 working environment ensuring protection for (non-hazardous) products.
[Show full text]
Double Seaming Process 41 Buyers Guide
CANTECH INTERNATIONAL MARCH 2014 www.cantechonline.comTech Can INTERNATIONAL MARCH 2014 Soft drinks: has the bubble Inside: burst? Redesigning rams Keeping seams seamless Inspection and testing systems March 2014 Contents March 2014 Volume 21, Number 6 Contents 22 CANTECH INTERNATIONAL MARCH 2014 www.cantechonline.comTech Can INTERNATIONAL MARCH 2014 Soft drinks: has the bubble Inside: burst? Redesigning rams Keeping seams seamless Inspection and testing systems 33 REGULARS Subscription Information 5 Comment DON’T MISS IT! An annual subscription to CanTech International includes 7 World News direct personal delivery of 10 issues per year, weekly email 38 Equipment News 12 newsletter and online access to back issues. The latest machinery and equipment for the can line16 Postal & Digital Issue One Year: 43 £168 UK; £178 Europe; 39 New Products £199 Rest of World Postal & Digital Issue Two Years: New cans and ends in the £292 UK; £315 Europe; market place £352 Rest of World 40 Digital Issue Only (1 year): 40 Filling Focus £160 To subscribe please email Russ Phillips updates readers [email protected] or on the canned craft beer go to www.cantechonline.com and market in the US and reviews click Subscribe. the best cans and beers 38 58 Candid Graham Fenton, chairman 18 Used & refurbished of The Can Makers, talks equipment 30 Inspection & testing to Candid following his Richard Piper takes a closer systems re-election look at the pros and cons Richard Piper talks to the Send address changes to: of new versus used or experts in the field of CanTech International, refurbished equipment inspection and testing, an The Maltings, 57 Bath Street, FEATURES area of vital importance to Gravesend, Kent DA11 0DF, UK.
[Show full text]
CT COVER SEP11.Indd
Supplier Proﬁle Imeta Company Description special cover feeders, gear driven lower lifters, IMETA has been designing and producing chucks inverter kit, end downstakers and much more. Imeta Srl and rolls, upgrading kits and spare parts for seam- Manufacturing of tools for can and cover produc- ers since 1964. The company’s products for can tion: curling disks and sectors, beading sector Strada Burla 279A making and canning industries are the result of and roller, spin-flangers, dies for open top ends. 43122 Parma in depth studies calling on extensive data banks Overhauling and trade of second-hand seamers Italy of 1,500 seaming profiles. Imeta has an operating and any can making machines. Tel: + 39 0521 1688811 structure that brings together the passion for detail, Fax: + 39 0521 1688819 Recent Developments typical and emblematic of the craftsman culture, E-mail: [email protected] As shown at Metpack, IMETA has recently devel- Web: www.imetasrl.com and the technological element of an industrial oped the new ‘DESMO KIT’ for Angelus 60L seamer. concern. The Kit includes: A ‘Box-style’ seaming cam that Key Personnel Facilities controls both the opening and the return paths of Administrators IMETA’s headquarters and manufacturing facili- the seaming levers at any speed. Guerrino Greci & Monica Greci ties are located in Parma, Italy. Technical skilled • A ‘Box-style’ ejector cam to ensure the correct agents are available worldwide. return of the Ejector Rods at any speed. Sales Manager Company News & Statistics • A set of Seaming Cam Levers, that allow a simpli- Roberto Baroni Founded in 1964, IMETA has about 50 employees fied smg roll setting and a faster can size change Technical Manager and has been ISO 9002 certified since 1999.
[Show full text]
Investigation of Corrosion in Canned Tomatoes Processed by Retorting
Investigation of Corrosion in Canned Tomatoes Processed by Retorting THESIS Presented in Partial Fulfillment of the Requirements for the Degree Master of Science in the Graduate School of The Ohio State University By Elliot Dhuey Graduate Program in Food Science and Technology The Ohio State University 2019 Master's Examination Committee: Dr. Melvin Pascall, Advisor Dr. Gerald Frankel Dr. John Litchfield Copyrighted by Elliot Dhuey 2019 Abstract This study investigated the presence of volatile and non-volatile compounds in canned processed tomatoes and how these compounds interacted with the Bisphenol A free epoxy-based lining of the cans to cause corrosion of the base metal and the migration of iron and tin compounds to the tomatoes. The tomatoes tested in this study were the Roma variety. They were sorted, washed, diced, and sealed in two-piece tinplated metal cans. These were processed by retorting at 250°F for 30 minutes then stored at 49°C for up to 50 days. Control samples were packaged and processed in glass jars. The presence and concentrations of the volatile and non-volatile compounds in the processed and unprocessed tomatoes were tested using Selected Ion Flow Tube – Mass Spectrometry (SIFT-MS) and Ion Chromatography – Mass Spectrometry (IC-MS) respectively. After removing the processed tomatoes from the cans, the linings were removed and analyzed for the volatile and non-volatiles as was mentioned before. Scanning Electron Microscopy (SEM) paired with Energy Dispersive X-ray Spectroscopy (EDS) was used to confirm the presence of visual corrosion in the processed cans and to analyze its elemental composition.
[Show full text]
Cask Brewing Systems Inc. Automated Canning Systems V4.1
Cask Brewing Systems Inc. Automated Canning Systems V4.1 Cask Automated Canning System Manual Confidential Automated Canning System Manual V4.1 Second Edition February 2014 Copyright © 2014 Cask Brewing Systems Inc. All rights reserved. Disclaimer The information presented in this manual has been reviewed and validated for accuracy. The included set of instructions and descriptions are accurate for the Cask Brewing Systems Inc. Automated Canning System Version 4.1 (ACS V4.1) in its stock condition as supplied by Cask Brewing Systems Inc., at the time of this manual's production. However, subsequent products and manuals are subject to change without notice. Therefore, Cask Brewing Systems Inc. assumes no liability for damages incurred directly or indirectly from errors, omissions, or discrepancies between any subsequent or altered products and this manual. www.cask.com Cask Brewing Systems Inc. – Calgary, AB, Canada V4.1 1- 800- 661-8443 2 Table of Contents Section A - Before You Begin Section D - ACS Operations • Unit Diagram 5 • Initial Startup Adjustments and Settings 31 • System Requirements 6 • ACS Prestart Checklist 33 • Unit Footprint 7 • ACS Startup and Operation 34 • ACS CIP System 35 Section B - Unit Set Up • CIP Procedure 36 • Uncrating 8 • ACS Post-Operation Shutdown Checklist 37 • Packing List 9 • System Periodic Maintenance ` 38 • Moving Unit into Position 10 • Install Adjustments and Settings 11 Trouble Shooting • Unloading Cans 12 • Lid Dispense Adjustment & Troubleshooting 39 • Air System Adjustment & Troubleshooting 42 Section C - Automated Canning System (ACS) Operations Overview Parts List 44 • System Operation Walkthrough 13 • HMI Panel 15 Frequently Asked Questions • Electrical Panel Breakdown 20 • Seamer 50 • Beer Manifold 23 • Lid Dispense 53 • Fill Head Manifold 24 • Filler 54 • Foam Valve Top Up 25 • Can Filling 26 • Lid Dispenser 27 • Parts in Motion Pneumatics 28 • Parts in Motion Motors 30 www.cask.com Cask Brewing Systems Inc.
[Show full text]
5 Metal Cans Bev Page, Mike Edwards and Nick May
5 Metal cans Bev Page, Mike Edwards and Nick May 5.1 Overview of market for metal cans The total world market for metal containers is estimated at 410 billion units per annum. Of this, drink cans account for 320 billion and processed food cans account for 75 billion. The remainder are aerosol and general line cans. Drink cans may be divided into those for non-carbonated drinks (liquid coffee, tea, sports drinks etc.) and carbonated beverages (soft drinks and beer), many of which pass through a pasteurisation process. 5.2 Container performance requirements Metal packages for food products must perform the following basic functions if the contents are to be delivered to the ultimate consumer in a safe and whole- some manner: • preserve and protect the product • resist chemical actions of product • withstand the handling and processing conditions • withstand the external environment conditions • have the correct dimensions and the ability to be practically interchange- able with similar products from other supply sources (when necessary) • have the required shelf display properties at the point of sale • give easy opening and simple/safe product removal • be constructed from recyclable raw materials. In addition, these functions must continue to be performed satisfactorily until well after the end of the stated shelf life period. Most filled food and drink containers for ambient shelf storage are subjected to some form of heat process to prolong the shelf life of the product. For food cans, this will normally pro- vide a shelf life of up to 2–3 years or more. The heat process cycles used to achieve this are particularly severe and the containers must be specifically designed to withstand these conditions of temperature and pressure cycles in a steam/water atmosphere.
[Show full text]
Food Processing Technology: Principles and Practice, Second
25 Filling and sealing of containers There have been significant developments in packaging systems during the last ten years, prompted by a number of considerations, for example: • marketing requirements for different, more attractive packs • reductions in pack weight to reduce costs and meet environmental concerns over energy and material consumption (Chapter 24) • new packaging requirements for minimally processed foods (Chapters 9, 18, 19) and modified atmosphere packaging (Chapter 20) • the need for new types of tamper-resistant and tamper evident packs. Packaging methods that have been developed to meet these requirements are described in subsequent sections. Accurate filling of containers is important to ensure compliance with fill-weight legislation and to prevent ‘give-away’ by overfilling. The composition of some foods (for example meat products such as pies and canned mixed vegetables) is also subject to legislation in some countries, and accurate filling of multiple ingredients is therefore necessary. The maintenance of food quality for the required shelf life depends largely on adequate sealing of containers. Seals are the weakest part of a container and also suffer more frequent faults during production, such as food trapped in a seal, incorrect sealing temperatures or can seamer settings. In this chapter the techniques used to fill and seal rigid and flexible containers are described. By themselves these operations have no effect on the quality or shelf life of foods, but incorrect filling or sealing has a substantial effect on foods during subsequent storage. 25.1 Rigid and semi-rigid containers ‘Commercially clean’ metal and glass containers are supplied as palletised batches, which are wrapped in shrink or stretch film (Section 25.1.3) to prevent contamination.
[Show full text]
Cannular Can Seamer Boksemaskin
Cannular Can Seamer boksemaskin Her kommer en forklaring på hvordan du justerer din Cannular Can Seamer Boksemaskin. NB! Vi anbefaler andre mål enn det Kegland gjør, da vi har hatt stor suksess med å bruke målene som er oppgitt her, ved justering. Du finner målene KegLand anbefaler lenger ned. Men som sagt, vi anbefaler disse målene. Målene vi har brukt ved justering er: Valse 1 (Den til venstre) Vertikalt: Bare så vidt det er mellomrom over chuck Ca 0,1 mm Horisontalt: 0,7 mm fra chuck Valse 2 (Den til høyre) Vertikalt 1,2mm-1,3mm over chuck Horisontalt 0,1mm Vi anbefaler å bruke en bladsøker når du skal justere din Cannular Can Seamer! Man bør ta en sjekk på at målene fortsatt stemmer ca 1 gang i året, eller etter ca 50.000 bokser. En guide for å justere din Cannular Can Seamer Introduction. This information provided will also be a useful guide to double seam practice for both line engineers and production operators. The principle objective of this guide is to assist personnel whose decisions determine the quality of the beverage double seam and whose judgment dictate whether double seam has integrity issues. The Cannular bench top seamer has brought seaming technology to a range of new small businesses and home brewers. Often small businesses like this are not able to justify bringing an independent engineer in to tweak or maintain the machine. This guide has been made so small business owners and home brewers can adequately equip themselves on how to maintain and setup the machine to get acceptable levels of productivity.
[Show full text]