DOCSLIB.ORG

Scissor Lift Accident in the West Hackberry Brine Tank-14 Resulting in Injury on February 7, 2013

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Scissor Lift Accident in the West Hackberry Brine Tank-14 Resulting in Injury on February 7, 2013 U.S. Department of Energy Office of Fossil Energy Accident Investigation Report Scissor Lift Accident in the West Hackberry Brine Tank-14 Resulting in Injury on February 7, 2013 June 2013 Strategic Petroleum Reserve West Hackberry Storage Site Cameron Parish, Louisiana Scissor Lift Accident in the West Hackberry Brine Tank-14 Resulting in Injury Disclaimer This report is an independent product of the Accident Investigation Board appointed by Christopher A. Smith, Acting Assistant Secretary, Office of Fossil Energy. The Board was appointed to perform an Accident Investigation and to prepare an investigation report in accordance with Department of Energy (DOE) Order 225.1B, Accident Investigations. The discussion of the facts as determined by the Board and the views expressed in the report do not assume and are not intended to establish the existence of any duty at law on the part of the U.S. Government, its employees or agents, contractors, their employees or agents, or subcontractors at any tier, or any other party. This report neither determines nor implies liability. Scissor Lift Accident in the West Hackberry Brine Tank-14 Resulting in Injury Scissor Lift Accident in the West Hackberry Brine Tank-14 Resulting in Injury Release Authorization On February 15, 2013, an Accident Investigation Board (the Board) was appointed to investigate an accident that resulted in serious injuries caused when a scissor lift tipped over in Brine Tank- 14 (WHT-14) at the Strategic Petroleum Reserve, West Hackberry, Louisiana, site on February 7, 2013. The Board’s responsibilities have been completed with respect to this investigation. The analysis and the identification of the direct cause, root causes, contributing causes, and judgments of need resulting from this investigation were performed in accordance with the Department of Energy (DOE) Order 225.1B, Accident Investigations. The report of the Accident Investigation Board has been accepted and the authorization to release this report for general distribution has been granted. Christopher A. Smith Acting Assistant Secretary Office of Fossil Energy Scissor Lift Accident in the West Hackberry Brine Tank-14 Resulting in Injury Scissor Lift Accident in the West Hackberry Brine Tank-14 Resulting in Injury Table of Contents Legend ........................................................................................................................................... iv Acronyms ........................................................................................................................................v Executive Summary ................................................................................................................ ES-1 1.0 Introduction ........................................................................................................................1 1.1 Appointment of the Board ...................................................................................... 1 1.2 Facility and Organization ........................................................................................ 1 1.2.1. Strategic Petroleum Reserve ....................................................................... 1 1.2.2. West Hackberry Site ................................................................................... 1 1.2.3. Office of Fossil Energy ............................................................................... 2 1.2.4. SPR Project Management Office in New Orleans, LA ............................... 3 1.2.5. Operating Contractor Organization............................................................. 3 1.2.6. Construction Contractor Organization ........................................................ 3 1.2.7. Subcontractor Organization ........................................................................ 3 1.3 Scope, Purpose and Methodology of the Accident Investigation ........................... 3 2.0 Facts and Analysis..............................................................................................................5 2.1 Description of Work Activity ................................................................................. 5 2.2 Accident Description .............................................................................................. 8 2.2.1. Accident Scene Analysis and Reconstruction............................................. 9 2.2.1.1. Force Analysis ........................................................................ 10 2.2.2. Chronology of Events ............................................................................... 12 2.3 Implementation of Integrated Safety Management System .................................. 16 2.3.1. Define the Scope of Work......................................................................... 16 2.3.2. Identify and Analyze Hazards Associated with the Work ........................ 19 2.3.3. Develop and Implement Hazard Controls ................................................. 25 2.3.4. Perform Work within Controls ................................................................. 30 2.3.4.1. PBC ......................................................................................... 30 2.3.4.2. AGSC ...................................................................................... 42 2.3.4.3. DM .......................................................................................... 44 2.3.4.4. DOE ........................................................................................ 44 2.3.5. Provide Feedback and Continue to Improve Safety Management ............ 45 2.4 Emergency Response ............................................................................................ 48 2.4.1. DOE and DM Responses .......................................................................... 49 2.4.2. Investigative Readiness and Scene Preservation ...................................... 50 2.4.2.1. Scene Preservation .................................................................. 50 i Scissor Lift Accident in the West Hackberry Brine Tank-14 Resulting in Injury 2.5 Barrier Analysis .................................................................................................... 51 2.6 Change Analysis ................................................................................................... 52 2.7 Event and Causal Factors Analysis ....................................................................... 52 3.0 Conclusions and Judgments of Need ..............................................................................55 4.0 Board Signatures ..............................................................................................................63 5.0 Board Members, Advisors and Consultants ..................................................................64 5.1 Biographies of Accident Investigation Board Members and Support .................. 65 Appendix A: Appointment of an Accident Investigation Board .................................. A-1 Appendix B: Barrier Analysis .......................................................................................... B-1 Appendix C: Change Analysis .......................................................................................... C-1 Appendix D: Event and Causal Factor Analysis ............................................................ D-1 Appendix E: Force Calculations on Scissor Lift ............................................................. E-1 ii Scissor Lift Accident in the West Hackberry Brine Tank-14 Resulting in Injury Figures Figure 1: West Hackberry Site, Cameron Parish, Louisiana ......................................................... 2 Figure 2: Accident Investigation Terminology .............................................................................. 4 Figure 3: WHT-14 at the SPR West Hackberry Site ..................................................................... 5 Figure 4: Skyjack SJIII 3226 Scissor Lift ...................................................................................... 6 Figure 5: Dimensional Specifications and Dimensions of the Skyjack SJIII 3226 ....................... 7 Figure 6: Overturned Scissor Lift in Tank ..................................................................................... 8 Figure 7: 3-D Rendering of Scissor Lift and Hose Prior to the Accident ...................................... 9 Figure 8: Manufacturer-Applied Label shows 0 wind and 90 lb side force ................................ 24 Figure 9: Breathing Air Filtration System ................................................................................... 29 Figure 10: Warning Label inside Scissor Lift Identifying Side Force Limitations ..................... 35 Figure 11: Position of the scissor lift in relation to work completed. .......................................... 39 Figure 12: Control Box with three-way switch pointing to the drive position ............................ 40 Figure E-1: Board Examining inside of WHT-14 and Scissor Lift ............................................ E-6 Figure E-2: WHT-14 and Scissor Lift in Relation to Manhole .................................................. E-7 Figure E-3: Scissor Lift in WHT-14 ........................................................................................... E-8 Figure E-4: Base of Scissor Lift in WHT-14 .............................................................................. E-9 Figure E-5: Outside Manhole of WHT-14 ...............................................................................
Load more

Recommended publications
  • Water Jet Solutions the Ultimate Water Jet Technology
    WATER JET SOLUTIONS THE ULTIMATE WATER JET TECHNOLOGY Water Jet Solutions Top quality with flexibility BlastOne is making water work for you! FEATURES BlastOne’s involvement in water lets you use this • Captive/Vacuum Systems tremendous technology to perform a huge range of • Safety applications – making projects go faster, cleaner • Accessories and safer. 1800 190 190 www.BlastOne.com WATER - WORKING FOR YOU The BlastOne Group is a superior supplier of BlastOne’s involvement in water lets you use this blasting and painting equipment. tremendous technology to perform a huge range of applications: industrial cleaning, concrete Large enclosed halls can be designed and demolition, surface preparation – making projects engineered to provide ventilation and visibility go faster, cleaner and safer. It also helps in for both painting and grit blasting. The abrasive removing huge environmental nightmares like recycling systems and high performance dust and silicosis issues. vacuums provide work efficiency, while humidity controlled air helps prevent oxidation and flash As further research has been done, water can now rusting of the steel between the blasting and be used for more and more applications – such as coating processes. cutting steel with very small amounts of abrasive injection, removing the need of oxy cutters, plasma The configuration of the rooms can be designed cutters, being able to do projects out on a jobsite around the ship modules to be coated. Ventilation that weren’t possible before. This enables you to systems are designed for end draft or downdraft do work in hazardous locations that would have configurations. previously required a complete plant shutdown Normally, because of the size of the rooms, a and the ability to work in gaseous atmospheres separate structure is required for the booth roof where previously it wasn’t safe to go.
    [Show full text]
  • Evaluation of Wet Blast Cleaning Units
    Evaluation of Wet Blast Cleaning Units by Itis universally acknowledged that dry blasting cannot remove tight millscale, tight ~~~~~~d R. Appleman abrasive blasting is the most efficient and rust, and paint, and while some power tools are Senior Editor economical technique for cleaning structural available for the removal of tight residues, they and steel for painting in industrial applications. The are less eficient than blast cleaning. Other new Joseph A. Bruno, Jr. abrasive blasting unit delivers to the surface a techniques have been described, but have not Technical Editor high velocity stream of hard, angular abrasive, yet proven practical for large scale production which has the ability to rapidly remove existing cleaning of steel. paints, rust, and millscale to roughen the base Wet abrasive blasting offers the potential metal for improved adhesion. The equipment to reduce or eliminate many of the problems and techniques for dry blasting have become associated with dry blasting and at the same fairly well standardized and provide a high time offers relatively high production rates degree of reliability. and cleaning efficiency. Dry blasting has been restricted in recent There are several generic types of wet years because of health hazards from silica dust blasting equipment with large variabilities in inhalation; air quality concerns with visibility, operating parameters, reliability, cleaning rates suspended particulates, and fugitive or nuisance and effectiveness, cost, safety, and user satis- dust; and dust contamination of machinery or faction. This article describes the results of equipment. There has also been concern about field evaluations of several different types and the disposition of the spent abrasive, which may manufacturers of equipment for wet blasting.
    [Show full text]
  • ACHIEVING EFFICIENCY in ABRASIVE BLAST CLEANING a JPCL Ebook Jpclpaintsquare.COM I
    ACHIEVING EFFICIENCY IN ABRASIVE BLAST CLEANING A JPCL eBook jpclPAINTSQUARE.COM i Achieving Efficiency in Abrasive Blast Cleaning A JPCL eBook Copyright 2012 by Technology Publishing Company 2100 Wharton Street, Suite 310 Pittsburgh, PA 15203 All Rights Reserved This eBook may not be copied or redistributed without the written permission of the publisher. SPONSORED BY Contents ii Contents iv Introduction Improving Blasting Productivity by Optimizing Operation Parameters 1 by Han-Jin Bae et al. Maintenance Tips: Abrasive Blasting: Achieving Efficiency and Profitability 9 by Patti Roman Applicator Training Bulletin: Controlling Quality During Abrasive Blasting 13 by Sara Kennedy Equipment Maintenance: Taking Care of Abrasive Blasting Equipment 17 by Patti Roman Problem Solving Forum: On the Cleanliness of Compressed Air for 21Abrasive Blasting by Patti Roman Equipment Maintenance: The Importance of Air Compressor Maintenance 23 by John Placke Maintenance Tips: Fishing for the Best Abrasive 27 by David Dorrow Maintenance Tips: Abrasive Selection Requires Evaluation of Needs, 29 Cost, and Productivity by Lori Huffman Peak Performance from Abrasives 32 by Hugh Roper, Ray Weaver, and Joe Brandon Problem Solving Forum: Checking Abrasives in the Field 40 by multiple authors Cover photo courtesy of CDC/NIOSH Introduction iv Introduction This eBook consists of articles from the Journal of Protective Coatings & Linings (JPCL) on abrasive blasting, and is designed to provide general guidance on the efficiency of abrasive blasting and maintenance of the associated equipment. iStockphoto Blasting Productivity 1 By Han-Jin Bae, Jae-Jin Baek, Chae- Suk Lee, Chil-Seok Shin, Byung-Hun Lee, Sang-Ryong Shin, Kwang-KI Baek, Hyundai lndustrlal Research Institute, and Ki-Soo Kim, Block Painting Dept., Improving Blasting Productivity Hyundal Heavy Industries Co.
    [Show full text]
  • Abrasive Blasting Environmental Requirements
    NASSCO Environmental Instruction #1: Environmental Requirements for Abrasive Blasting Abrasive blasting operations are very closely regulated by the San Diego Air Pollution Control District. Since these operations are subject to strict local and federal laws, all abrasive blasting activities conducted at NASSCO are required to be carefully controlled at all times to ensure compliance. For questions about these or any other NASSCO environmental requirements, call 619-544-7506. Before You Begin NASSCO Approval Your company may not perform abrasive blasting at any NASSCO facility without first applying for and obtaining approval from the Environmental Engineering Department to conduct this activity. Separate approval must be obtained for each abrasive blasting job conducted (one per ship or location). To apply for approval, a completed and signed copy of “NASSCO Environmental Form #1: Request for Authorization to Perform Abrasive Blasting at NASSCO Facility” to the NASSCO Environmental Engineering Department at [email protected] or fax to 619-744-1088. You may not begin abrasive blasting until approval has been received from the Environmental Engineering Department. Permits Most abrasive blasting operations require an air pollution control permit. The San Diego Air Pollution Control District (SDAPCD) is the permitting agency for stationary and portable abrasive blasting operations operated solely within San Diego County. Alternatively, portable abrasive blasting operations can be registered with the California Air Resource Control Board (CARB) portable equipment registration program, which authorizes statewide operation of the equipment. Your company is responsible for obtaining and maintaining the appropriate permit or registration for your abrasive blasting, as required. For more information about San Diego County’s permitting program, contact SDAPCD at 858-586-2600, or visit www.sdapcd.org.
    [Show full text]
  • The Power of Prep Surface
    22 D+D DECEMBER 2014 Q+ Got a concrete problem? Concrete A Ask the experts: [email protected]. By Fred Goodwin, FICRI, FACI, BASF Construction Chemicals he success or failure of any concrete coating or repair application is likely to be determined before the first drop of product ever touches the The Power of Prep surface. Surface preparation of con- Proper surface preparation on concrete means T crete is probably the most important consideration for successful coating and the difference between coating success and failure. repair material application. The Society for Protective Coatings’ ations. However, SSPC SP-13 states “An ac- scarifying, flame blasting, shotblasting, and standard SSPC SP-13/NACE No. 6 Surface ceptable prepared concrete surface should the use of surface retarders. ICRI 310.2 Preparation of Concrete defines surface be free of contaminants, laitance, loosely ad- Selecting and Specifying Concrete Surface preparation as: “The method or combina- hering concrete, and dust, and should pro- Preparation for Sealers, Coatings, Polymer tion of methods used to clean a concrete vide a sound, uniform substrate suitable for Overlays, and Concrete Repair discusses surface, remove loose and weak materials the application of protective coating or lining each method. and contaminants, repair the surface, and systems.” Whatever the method, the goal is an roughen the surface to promote adhesion.” Common concrete surface preparation acceptably prepared concrete surface. Let’s methods include abrasive blasting, acid take
    [Show full text]
  • Surface Preparation Repair
    Technical guideline Surface preparation Maintenance and repair Cleanliness requirements Introduction • Low salt level. High salt contamination can result in paint blisters and promote corrosion. This guideline presents a survey of key elements relevant for • No oil and grease. Oil and grease can cause delamination/ surface preparation during repair and maintenance. The flaking of the paint layer applied. guideline is not intended to give a complete description of all • Free of dust. Dust can result in loss of adhesion. surface preparation methods used in the industry. For more • Free of rust or other corrosion products. Rust gives poor detailed information, consult the actual standards behind the adhesion and can result in blistering. described methods whenever these are available. • Free of mill scale: Mill scale can cause galvanic corrosion and poor adhesion. Maintenance and repair work is characterised by the following: • The substrate has previously been painted and old paint must be removed partly or in full. Roughness profile • Often access is hampered by other on-going site activities, The purpose of the roughness profile is to secure an anchor environmental restrictions as well as restraints in relation to profile for optimal adhesion of the new paint. This requires that time and climate. the surface has an adequate roughness where previous paint has been removed and that any remaining paint has the adequate adhesion. Content The roughness profile is rated according to the Grit comparator or the Shot comparator as defined in the requirements of the The guideline covers these topics: paint specification. Please find more information on roughness in ISO 8503-2:2000.
    [Show full text]
  • UHP WATERJETTING – the OLDEST - NEW METHOD for SURFACE PREPARATION Brady Deroche, Innovative Surface Prep Gray, Louisiana
    UHP WATERJETTING – THE OLDEST - NEW METHOD FOR SURFACE PREPARATION Brady DeRoche, Innovative Surface Prep Gray, Louisiana ABSTRACT With the growing concerns over change in Federal regulations, and the increase in waste disposal costs, the oil and gas maintenance industry is in need of an alternative solution to fit these specifications. They are in need of an innovative tactic that is controlled, safe, predictable, and most importantly, able to provide an ultra-clean surface that meets the set industry performance standards. Little do most people know, this solution we are all looking for was created in the early 1800s, and used by coal miners as a method to remove loose debris and coal. This solution is the use of water pressure to remove contaminants and various materials. The method has evolved since the early 1800s to now use ultra-high-pressure water to effectively remove coatings and contaminants from surfaces. The process is now known as UHP Waterjetting. In 1994, the US Navy embraced this method as a means to reduce waste streams, and provide a solution to ships breaking up at sea because of corrosion. Surface preparation techniques have evolved with the acceptance of UHP waterjetting (UHP WJ). The new technique has proven to provide benefits in not only workflow, but also in the overall project’s pocketbook as well. With quality requirements rising and budgets for maintenance activities decreasing, UHP WJ has become the ideal surface preparation solution. With abrasive users still hesitant to make the change to water, this paper aims to provide you with a wealth of knowledge surrounding the topic and more details on one popular method of utilizing this solution, remote controlled robotics.
    [Show full text]
  • Surface Treatment Solutions Product Selection Guide AIRBLAST
    Surface Treatment Solutions Product Selection Guide AIRBLAST www.airblast.com AIRBLAST The Airblast Group Since 1974 Airblast has been the world leader in providing blasting and painting solutions to the anticorrosion industries. With an unparalleled network of offices around the world Airblast works closely with our customers and distribution partners providing tried and tested equipment as well as developing customized solutions for specific applications. The range of equipment sold by Airblast includes: ● Traditional blasting machines & accessories ● Shot blasting machines ● Blasting & painting rooms ● Blasting robots ● Metallization rooms ● Vacuum recovery systems ● Abrasive recycling systems ● Dust collectors ● Dehumidification equipment ● Inspection equipment Airblast equipment is used in the following industries: ● Metal & steel construction ● Shipbuilding ● Petrochemical ● Oil and gas ● Wind energy ● Railway rolling stock ● Casting Airblast-Abrasives B.V. Airblast-Abrasives B.V. was founded in 2014 and produces Steel Shot and Steel Grit of the highest quality. Airblast- Abrasives also supplies a complete range of abrasives in every size and hardness. The Airblast-Abrasives team is available to assist customers in selecting the right abrasive mixture and to analyze the work process in order to maximize efficiency. All abrasives are subject to strict quality control to ensure delivery of the best available materials. Airblast Group Commitments Airblast is dedicated to maintain a profitable organization on a long term basis through ethically and morally sound business practices. By investing in the long term future of our organization, and those with whom we conduct business, Airblast believes that we can share sustained mutual success. Our manufacturing facilities in Europe and the Far East produce fit for purpose quality products with region specific certification.
    [Show full text]
  • Chloride Removal Using “Recyclable Encapsulated Abrasive Media”
    ____________________________________________________________________________________________TECHNICAL PAPER RE-PRINT Chloride Removal Using “Recyclable Encapsulated Abrasive Media” Michael Merritt, Sponge-Jet, Inc. From: The Power of Paint & Coatings; Conference Proceedings 2010 Phoenix, AZ ▪ February 7-10, 2010 Reprinted with Permission from The Society for Protective Coatings ____________________________________________________________________________________________ © 2010 SPONGE-JET, INC. CHLORIDE REMOVAL USING “RECYCLABLE ENCAPSULATED ABRASIVE MEDIA” Michael Merritt Sponge-Jet, Inc Portsmouth, NH USA ABSTRACT: This paper presents results of multiple test programs that have been performed to determine the effectiveness of recyclable encapsulated abrasive media to remove chlorides during surface preparation. Tests published in 2002 concluded that this technology consistently achieves significant reductions of chloride levels in comparison to those achieved with conventional abrasive blasting. However, those tests were conducted with new media and not recycled media; leaving questions regarding the effect of recycling and possible re-deposition of contaminates on the surface. Recent tests indicate that chloride removal can be efficiently performed while recycling encapsulated abrasive media and no detrimental effect on removal rates occurs with increased recycles; in fact, increased cycles showed a slight improvement in removal efficacy. Test results also indicate that blasting with encapsulated abrasive media can frequently reduce chloride concentrations to below typically specified levels. This process compares favorably in both cost and speed to other technologies, which often require a multi-step procedure such as abrasive blast, water or chemical wash and final abrasive blast to achieve specified levels of surface contaminants. BACKGROUND INFORMATION ON ENCAPSULATED ABRASIVE MEDIA Encapsulated Abrasive Media was invented in the late 80’s and has grown in use as an accepted form of abrasive blasting since that time.
    [Show full text]
  • Abrasive Blasting Operations, Engineering Control and Work
    ABRASIVE BLASTING OPERATIONS Engineering Control and Work Practices Manual Enviro-Management & Research, Inc. Washington, D.C. 20001 FINAL REPORT Contract No. 210-75-0029 U.S " DEPARTMENT OF HEALTH, EDUCATION, AND WELFARE Public Health Service Center for Discese Control National Institute for Occupational Safety and Health Division of Physical Sciences and Engineering Cincinnati, Ohio 45226 March 1976 For allle by the Superintendent of Documents , U .S. Government PtlntJni Otfice , Wa8hington. D.C. 2 0402 ACKNOWLEDGDAENTS This contract was conducted by Enviro Management &Research, Inc. under contract COC-210-75-0029 for the Division of Physical Sciences and Engineering. National Institute for Occupational Safety and Health, Center for Disease Control. Department of Health, We acknowledge with grateful appreciation the assistance provided by the Education and Welfare. Technical monitoring was proVided by Robert T. Hughes, Control Technology Research Branch. American Foundrymen's Society and The American Iron and Steel Institute, This report is reproduced as received from the contractor. The conc7usions and recommendations contained herein represent the va r l'OUS manufacturers of abrasl've blastl'ng equl'pment, and Mr. Robert T. Hughes, opinion of the contractor and do not necessarily constitute NIOSH endorsement Engineering Branch, Division of Physical Sciences and Engineering, National Institute for Occupational Safety and Health. HEW Publication No. (NIOSH) 76 -179 iii ii CONTENTS ABSTRACT vii L UTRODUCTION 1 II. CURRENT METHODS AND OPERATIONS 2 1. ~~ thods of Applicat ion 3 1.1 Dry blasting 1.2 Wet blastLTlg 12 2. Abrasives in common use 3. Abrasive Blasting Equipment 13 3.1 Portable blast cleaning machines 15 3.2 Hand-operated lli~its in blast cleaning rooms J.5 3.3 Hand-operated cabinet type blast cleaning 18 machines 3.4 Automatic blast cleaning machLTles 20 3.5 Wei blast cleanL~g machines 22 III.
    [Show full text]
  • Concrete Surface Preparation for Floor Coatings
    TECHNICAL BULLETIN Concrete Surface Preparation for Floor Coatings Page 1 Preparing Concrete Slab potentially a failure in any coating system applied where The most difficult aspect of satisfactorily coating a hydrostatic pressure exists. Because the effects of hydro- concrete floor is preparing the floor to ensure the static pressure can not be predicted, there exists no coating system will adhere. The following tests should be guarantee by Diamond Vogel that any coating will be able performed to determine the extent of surface preparation to withstand the forces capable of causing failure in the required to ensure a successful coating application. concrete substrate. Test for Curing Compound: Test Adhesion of Previous Coatings: Most concrete has a chemical curing agent applied at the Some coating systems do not require the complete time it is poured. Such chemical curing agents frequently removal of previously applied coatings in order to repaint prevent adhesion of coatings. Test for curing compound the floor, but all existing coating that remains that is by applying a muriatic acid solution to bare concrete. If the painted over must be tightly adherent. After required solution does not react (bubble vigorously), when in mechanical and chemical cleaning of the surface is contact with the concrete, the presence of a curing com- accomplished, cut 2”x2” “X” cross-hatches into remaining pound is indicated. Check various areas of the floor. Curing coatings. Then, apply 6” stripes of duct tape over the X’s, compounds must be either chemically or press the duct tape firmly onto the floor, and then quickly mechanically removed prior to coating.
    [Show full text]
  • What Effect Does Waterjet Cleaning Have on the Surface And
    2007 American WJTA Conference and Expo August 19-21, 2007 • Houston, Texas Paper WHAT EFFECT DOES WATERJET CLEANING HAVE ON THE SURFACE AND SURFACE PREPARATION? L. Frenzel Advisory Council San Marcos, Texas USA ABSTRACT This paper is a refresher on the effect that pressurized water has on the gross and microscopic details of a substrate. The paint and cleaning industry “knows” that waterjet cleaning doesn’t create an anchor “profile.” However, some industries, such as automotive engine parts, use a waterjet process to create the profile over which a hard coating is placed. The difference between a profile created by abrasive blast and the profile that is created, or cleaned, by waterjet will be examined. The effect on adhesion values will also be examined. Organized and Sponsored by the WaterJet Technology Association 1 INTRODUCTION The coatings and corrosion industries tend to learn by experience within a fairly closed network. Around 1977, when I first observed the effect of 140 MPa (20,000 psi) waterjet cleaning on new, old corroded, and painted steel surfaces, I didn’t know what I was seeing. The surface looked so different from those obtained by dry abrasive blast cleaning. I read all the papers that were published by the WaterJet Technology Association in the USA and the BHRA group in Europe and thought about the traditional surface as we think of it in the coatings industry. Many of the initial waterjet (WJ) papers were written by academicians. They were filled with equations and centered on cutting, not cleaning. The phenomenon of what happens to the surface when a droplet traveling at high velocity hits it is found in cavitation studies in the marine, rocket, and aircraft industry, but not in the coatings literature.
    [Show full text]