Micro MV V.5 / Micro 100 Operator Manual (Enron Modbus)
Total Page:16
File Type:pdf, Size:1020Kb
MicroMVG OPERATORS MANUAL Flow Computer Gas Version5 12603 Southwest Freeway, Suite 320 Stafford, Texas 77477 USA (281) 565-1118 Fax (281) 565-1119 Date: 8/13/2013 WARRANTY Dynamic Flow Computers warrants to the owner of the Smart Flow Computer that the product delivered will be free from defects in material and workmanship for one (1) year following the date of purchase. This warranty does not cover the product if it is damaged in the process of being installed or damaged by abuse, accident, misuse, neglect, alteration, repair, disaster, or improper testing. If the product is found otherwise defective, Dynamic Flow Computers will replace or repair the product at no charge, provided that you deliver the product along with a return material authorization (RMA) number from Dynamic Flow Computers. Dynamic Flow Computers will not assume any shipping charge or be responsible for product damage due to improper shipping. THE ABOVE WARRANTY IS IN LIEU OF ANY OTHER WARRANTY EXPRESS IMPLIED OR STATUTORY. BUT NOT LIMITED TO ANY WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE, OR ANY WARRANTY ARISING OUT OF ANY PROPOSAL, SPECIFICATION, OR SAMPLE. LIMITATION OF LIABILITY: DYNAMIC FLOW COMPUTERS SHALL HAVE NO LIABILITY FOR ANY INDIRECT OR SPECULATIVE DAMAGES (INCLUDING, WITHOUT LIMITING THE FOREGOING, CONSEQUENTIAL, INCIDENTAL AND SPECIAL DAMAGES) ARISING FROM THE USE OF, OR INABILITY TO USE THIS PRODUCT. WHETHER ARISING OUT OF CONTRACT, OR UNDER ANY WARRANTY, IRRESPECTIVE OF WHETHER DFM HAS ADVANCED NOTICE OF THE POSSIBILITY OF ANY SUCH DAMAGE INCLUDING, BUT NOT LIMITED TO LOSS OF USE, BUSINESS INTERRUPTION, AND LOSS OF PROFITS. NOTWITHSTANDING THE FOREGOING, DFM’S TOTAL LIABILITY FOR ALL CLAIMS UNDER THIS AGREEMENT SHALL NOT EXCEED THE PRICE PAID FOR THE PRODUCT. THESE LIMITATIONS ON POTENTIAL LIABILITY WERE AN ESSENTIAL ELEMENT IN SETTING THE PRODUCT PRICE. DFM NEITHER ASSUMES NOR AUTHORIZES ANYONE TO ASSUME FOR IT ANY OTHER LIABILITIES Date: 8/13/2013 CHAPTER 1: QUICK START.................................................................................................................... 1-1 Introduction: ............................................................................................................................................ 1-1 Quick Start Up ......................................................................................................................................... 1-2 Technical Data ......................................................................................................................................... 1-4 Parts List .................................................................................................................................................. 1-5 System Minimum Requirements ......................................................................................................... 1-7 What is a configuration file? ................................................................................................................... 1-8 Downloading a configuration file to the flow computer. ......................................................................... 1-8 What is an Image File? ............................................................................................................................ 1-9 How to download an Image File .............................................................................................................. 1-9 How to force a board into download mode............................................................................................ 1-10 Website - DFM Configuration Software ............................................................................................... 1-11 Website – Image File (Firmware) .......................................................................................................... 1-12 Getting acquainted with the flow computer wiring: .............................................................................. 1-13 Back terminal wiring: ........................................................................................................................ 1-13 Back Panel Jumper ............................................................................................................................ 1-14 INPUT/OUTPUT: Assigning and Ranging Inputs ............................................................................... 1-15 Input/Output Assignment .................................................................................................................. 1-15 How to assign a transmitter to an I/O point through window program: ............................................ 1-15 How to assign a transmitter to an I/O point through DOS program: ................................................. 1-15 Ranging the Transmitter Inputs: ........................................................................................................ 1-16 WIRING: ............................................................................................................................................... 1-17 Wiring the analog inputs: .................................................................................................................. 1-17 RTD ................................................................................................................................................... 1-18 Wiring analog output: ........................................................................................................................ 1-19 Turbine input wiring .......................................................................................................................... 1-20 Turbine input wiring – Using Daniel 1817 Preamp ........................................................................... 1-21 Turbine input wiring – Using Daniel 1818 Preamp ........................................................................... 1-22 RS-232 connection: ........................................................................................................................... 1-23 Printer Connection: ............................................................................................................................ 1-24 RS-485: .............................................................................................................................................. 1-25 Wiring of status inputs: ..................................................................................................................... 1-26 Wiring of switch/pulse outputs: ......................................................................................................... 1-27 Switch Output to Relay Wiring Diagram .......................................................................................... 1-28 Density input wiring: ......................................................................................................................... 1-29 CALIBRATION Through DOS Program .............................................................................................. 1-30 Analog Input 4-20mA or 1-5 volt signal .......................................................................................... 1-30 RTD calibration: ................................................................................................................................ 1-31 Calibration of analog output: ............................................................................................................. 1-32 Multi-Variable Transmitters (Model 205) – DP and Pressure ........................................................... 1-33 Multi-Variable Transmitters (Model 205)- RTD ............................................................................... 1-34 Verifying digital inputs and outputs ...................................................................................................... 1-35 CHAPTER 2: Data Entry ............................................................................................................................ 2-1 Introduction to the MicroMVG Software ................................................................................................ 2-1 Configuration File through DOS Program............................................................................................... 2-1 About ................................................................................................................................................... 2-1 File ........................................................................................................................................................... 2-2 Open a File .......................................................................................................................................... 2-2 Open a New File .................................................................................................................................. 2-2 Delete a File ......................................................................................................................................... 2-2 Load File.............................................................................................................................................. 2-2 View File ............................................................................................................................................. 2-2 Save As ...............................................................................................................................................