SECTION 11 11 Sealers PRODUCT PAGE Guide to Seals

TECHNICAL DATA SHEET Sec SECTION 11 11 Sealers PRODUCT PAGE Guide To Seals...... 11-3

ANTI SLIP ADDITIVE Grip Aid...... 11-5

SOLVENT BASED

AggreGloss™ J25...... 11-7 Sealers AggreGloss™ Satin J25S...... 11-9 Anti Spall J33...... 11-11 Tuf Seal™ J35...... 11-13 Tuf Seal™ Satin J35S...... 11-15

WATER BASED / EARTH FRIENDLY Ultra Seal EF...... 11-17

American Owned American Made

Visit www.daytonsuperior.com for the most up to date technical information 11-1

® Guide to ® Seals

TECHNICAL DATA SHEET Sec

What are the expectations of the Sealer Application 11 ■■ To be topically applied or penetrating Apply the sealer in accord with the manufactures ■■ Water repellency recommendations ■■ Color or one that is transparent Several thin applications better than one heavy application ■■ Increased abrasion resistance ■■ Chemical resistance.. & to which chemicals Apply uniformly for best performance & esthetic value ■■ Dustproofing Always recommend a mock-up using the same applicator that ■■ Glossy surface will do the job; Texture, color, uniformity, transparency are all ■■ Light reflectance subjective. ■■ Potable water approval

Sealers Dayton Superior Sealers A sealer is not a curing compound, nor a curing & sealing Acrylic, Water-Based, breathable: compound, and can not be expected to compensate for concrete Ultra Seal EF that is inadequately cured. ■■ High solids ■■ Non-yellowing Considerations in Selecting a Sealer ■■ VOC of 95 g/L Is it a vapor barrier, or breathable ■■ Low odor Is the application interior or exterior ■■ High gloss What are the main benefits the owner is looking to receive ■■ Excellent UV stability

Is there a warranty required Gas/oil resistant, breathable methacrylate-based (solvent): Does the sealer contribute to making the surface more slippery Tuf Seal™ J35* ■ How soon after concrete placement can the sealer be applied ■ USDA Approved What is the recommended surface preparation for the sealer High gloss, breathable sealer, methacrylate based How is the material applied (spray & run, or dump & scrub) (solvent): AggreGloss ™J25* Turn-around time (how soon can the area treated surface be ■■ USDA Approved used) Anti-Spalling Compound, Linseed oil-based: Surface Preparation: Surfaces should be clean, free of oil, ■■ Anti Spall J33 grease, dirt, paint, curing compounds and the like. Anti-Slip translucent powder for cure & seals and sealers: On burnished or extremely dense floors, older dirty floors or for ■■ Grip Aid epoxy urethane applications, mechanical surface preparation is recommended (such as: high pressure water, shot blasting, sand blasting) *NOTE: The J25 and J35 are also available in a satin finish, J-25S and J-35S Preparation Before Application: When using a sealer that is a vapor barrier always perform a vapor transmission (VT) test after the surface preparation is completed and just prior to the material application. VT can cause surface defects & weaken the bond of the sealer to the substrate. Verify all traces of curing membranes and / or other contaminants are removed from the surface. Be sure all materials have been preconditioned per manufacturers recommendation. Always mix the sealer prior to use.

American Owned American Made 10/03/11 • Page 1 of 1

Visit www.daytonsuperior.com for the most up to date technical information 11-3

® Grip Aid ® Anti Slip Additive

TECHNICAL DATA SHEET Sec

DESCRIPTION LIMITATIONS 11 Grip Aid is a very fine anti-slip powder that adds texture to most FOR PROFESSIONAL USE ONLY clear or colored sealers Do not roll or brush excessively to avoid agglomeration of the Grip Aid. USE Do not use filters in spray equipment. When added to a sealer, the Grip Aid provides slip resistance providing a “bite” to the concrete surface, without being highly abrasive. PRECAUTIONS READ MSDS PRIOR TO USING PRODUCT ■ FEATURES ■ Avoid breathing dust. ■■ Use with adequate ventilation

■■ Will reduce slipperiness of concrete surface Sealers ■ ■■ Makes the surface easier to walk on ■ Wear protective clothing, gloves and eye ■■ Will not affect topcoat color protection (Goggles, Safety Glasses and/or Face Shield) ■ ■■ Can be used for interior and exterior applications ■ Keep out of the reach of children ■■ Do not take internally ESTIMATING GUIDE ■■ In case of ingestion, seek medical help immediately Add 3.2 oz. (90.72 g) to one gallon (3.79 L) of sealer and 16 oz. ■■ May cause skin irritation upon contact, especially (453.59 g) to 5 gallons (18.93 L) of sealer. Apply the sealer at a prolonged or repeated. If skin contact occurs, wash coverage rate recommended by the sealer manufacturer. immediately with soap and water and seek medical help as needed PACKAGING ■■ If eye contact occurs, flush immediately with clean water and seek medical help as needed ITEM # PACKAGE SIZE ■■ Dispose of waste material in accordance with federal, state Ounces Grams and local requirements 273496 Plastic Bottle 3.2 90.72 273497 Plastic Bottle 16 453.59

STORAGE Store in a dry area. Shelf life is 18 months from date of manufacture in unopened containers.

APPLICATION Mixing: Add a 3.2 oz. (90.72 g) Container of Grip Aid to one (1) gallon (3.79 L) of sealer, or a 16 oz. (453.59 g) Container to five (5) gallons (18.93 L) of sealer. Mix thoroughly, and often, prior to and during application.

Placement: Roller or spray application is recommended. Apply per the sealer instructions. Small areas may be brushed. Apply uniformly.

CLEAN UP Clean up in accord with the recommendations of the sealer manufacturer

American Owned American Made 10/07/11 • Page 1 of 2

Visit www.daytonsuperior.com for the most up to date technical information 11-5 TECHNICAL DATA SHEET Grip Aid CONTINUED Anti Slip Additive

MANUFACTURER Sec Dayton Superior Corporation 1125 Byers Road 11 Miamisburg, OH 45342 Sealers Customer Service: 888-977-9600 Technical Services: 866-329-8724 Website: www.daytonsuperior.com

WARRANTY Dayton Superior Corporation (“Dayton”) warrants for 12 months from the date of manufacture or for the duration of the published product shelf life, whichever is less, that at the time of shipment by Dayton, the product is free of manufacturing defects and conforms to Dayton’s product properties in force on the date of acceptance by Dayton of the order. Dayton shall only be liable under this warranty if the product has been applied, used, and stored in accordance with Dayton’s instructions, especially surface preparation and installation, in force on the date of acceptance by Dayton of the order. The purchaser must examine the product when received and promptly notify Dayton in writing of any non-conformity before the product is used and no later than 30 days after such non-conformity is first discovered. If Dayton, in its sole discretion, determines that the product breached the above warranty, it will, in its sole discretion, replace the non-conforming product, refund the purchase price or issue a credit in the amount of the purchase price. This is the sole and exclusive remedy for breach of this warranty. Only a Dayton officer is authorized to modify this warranty. The information in this data sheet supersedes all other sales information received by the customer during the sales process. THE FOREGOING WARRANTY SHALL BE EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND ALL OTHER WARRANTIES OTHERWISE ARISING BY OPERATION OF LAW, COURSE OF DEALING, CUSTOM, TRADE OR OTHERWISE.

Dayton shall not be liable in contract or in tort (including, without limitation, negligence, strict liability or otherwise) for loss of sales, revenues or profits; cost of capital or funds; business interruption or cost of downtime, loss of use, damage to or loss of use of other property (real or personal); failure to realize expected savings; frustration of economic or business expectations; claims by third parties (other than for bodily injury), or economic losses of any kind; or for any special, incidental, indirect, consequential, punitive or exemplary damages arising in any way out of the performance of, or failure to perform, its obligations under any contract for sale of product, even if Dayton could foresee or has been advised of the possibility of such damages. The Parties expressly agree that these limitations on damages are allocations of risk constituting, in part, the consideration for this contract, and also that such limitations shall survive the determination of any court of competent jurisdiction that any remedy provided in these terms or available at law fails of its essential purpose.

® 10/07/11 • Page 2 of 2

11-6 Visit www.daytonsuperior.com for the most up to date technical information ® AggreGloss™ J25 ® Concrete Sealer

TECHNICAL DATA SHEET Sec

DESCRIPTION 11 AggreGloss™ J25 is a formulation of 25% methacrylate STORAGE copolymers in an aromatic solvent. AggreGloss™ J25 is a Store material in a horizontal position to prevent moisture clear sealer that will not yellow under exposure to sunlight. accumulation on the drum head. The AggreGloss™ J25 forms a tenacious bond to the concrete surface and provides a long lasting high gloss film. Shelf life is 24 months from date of manufacture in unopened containers. Do not store below 0°F (-18°C). USE AggreGloss™ J25 will seal, dustproof and enhance the beauty APPLICATION of new and old concrete. It is a film forming sealer for concrete, Surface Preparation: Surface must be clean, dry, free of grease,

stamped concrete, exposed aggregate concrete or pavers. dirt, paint and effloresence (white residue). If the substrate is Sealers AggreGloss™ J25 allows the substrate to breathe while wet from the rain or from surface cleaning, wait a minimum of protecting it from rain and airborne contaminants. 24 hours to allow the surface to dry completely before applying. Repair all defects prior to sealing. Protect or avoid spraying FEATURES AggreGloss™ J25 on glass or metal. ■■ Protects against rain ■■ Non-yellowing Placement: Apply AggreGloss™ J25 with low pressure spray, ■■ Excellent adhesion to substrate roller or brush. Apply uniformly without interruption to prevent ■■ Inhibits attack by airborne contaminants streaking. Hold sprayer nozzle perpendicular to the surface and ■■ Breathable film overlap each coat. In order to reduce loss of material to the ■■ High gloss finish atmosphere, avoid high pressures when spraying and too fine a ■■ Resists mildew and surface staining spray. Ensure spray nozzle is allowing for a uniform spray pattern ■■ Inhibits efflorescence without tailings or drips. Coverage will vary with the density and texture of the surface. Apply the AggreGloss™ J25 to achieve a complete, uninterrupted film. Avoid applications that are too PROPERTIES heavy or too light. Heavy coats can bubble and reduce moisture Dry time: Approx. 2 hours at 70°F (21°C) for re-coating or light vapor transmission. Too light of an application may not allow traffic. Wait 12 hours for heavy traffic Dry time is temperature, material to form a complete film. Avoid application during humidity and wind dependent excessively hot air or substrate temperatures (>90˚F, 32.2˚C).

ESTIMATING GUIDE CLEAN UP Approximate Coverage Rates: For tools and equipment use xylol or lacquer thinner. Sq. Ft./Gal Sq M/Liter 1st coat 200 – 300 4.9 – 7.4 LIMITATIONS 2nd coat 400 – 600 9.8 – 14.8 FOR PROFESSIONAL USE ONLY For applications of a sealer in an enclosed structure, Dayton Texture and absorption rate of the concrete will influence Superior recommends a water based product like the Ultra Seal coverage rate. Two coats of AggreGloss™ J25 are recommended. EF. Allow the first coat to dry before applying the second coat. Sprayers and equipment should have neoprene or viton type hose and gaskets. PACKAGING Allow 24 hours after rain before application. ITEM # PACKAGE SIZE Gallons Liters Do not apply at temperatures below 40°F (4 °C) or when the average daily temperature remains below 40°F (4°C). 69058 Jug (36 min.) 1 3.79 AggreGloss™ J25 is not intended for areas subject to high 69057 Pail 5 18.93 abrasion, such as bridge decks and roadways. 69056 Drum 55 208.20 Do not use AggreGloss™ J25 on bituminous surfaces, staining will result.

American Owned American Made 10/07/11 • Page 1 of 2

Visit www.daytonsuperior.com for the most up to date technical information 11-7 ™ TECHNICAL DATA SHEET AggreGloss J25 CONTINUED Concrete Sealer

Will interfere with the adhesion of sealants, thus avoid spraying MANUFACTURER Sec AggreGloss™ J25 into a joint prior to installation of sealant. Dayton Superior Corporation Apply to concrete that is a minimum of 7 days old. 1125 Byers Road 11 Miamisburg, OH 45342 Sealers Not for use under resinous (epoxy, polyester, urethane, etc.) Customer Service: 888-977-9600 coatings. Technical Services: 866-329-8724 Film may show black rubber tire marks. Website: www.daytonsuperior.com Not resistant to gas, oil, brake fluid, etc. WARRANTY Dayton Superior Corporation (“Dayton”) warrants for 12 months from the date of Will darken color of concrete surfaces manufacture or for the duration of the published product shelf life, whichever is less, that at the time of shipment by Dayton, the product is free of manufacturing defects and conforms to Dayton’s product properties in force on the date of acceptance by Dayton of the order. Dayton shall only be liable under this warranty if the product has PRECAUTIONS been applied, used, and stored in accordance with Dayton’s instructions, especially READ MSDS PRIOR TO USING PRODUCT surface preparation and installation, in force on the date of acceptance by Dayton of the order. The purchaser must examine the product when received and promptly notify ■■ Keep material and containers away from high heat, open Dayton in writing of any non-conformity before the product is used and no later than 30 days after such non-conformity is first discovered. If Dayton, in its sole discretion, flames, sparks or other sources of ignition determines that the product breached the above warranty, it will, in its sole discretion, replace the non-conforming product, refund the purchase price or issue a credit in the ■■ Use with adequate ventilation amount of the purchase price. This is the sole and exclusive remedy for breach of this warranty. Only a Dayton officer is authorized to modify this warranty. The information ■■ Wear protective clothing, gloves and eye in this data sheet supersedes all other sales information received by the customer protection (Goggles, Safety Glasses and/or Face Shield) during the sales process. THE FOREGOING WARRANTY SHALL BE EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES ■■ Keep out of the reach of children OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND ALL OTHER WARRANTIES OTHERWISE ARISING BY OPERATION OF LAW, COURSE OF DEALING, ■■ Do not take internally CUSTOM, TRADE OR OTHERWISE.

■■ In case of ingestion, seek medical help immediately Dayton shall not be liable in contract or in tort (including, without limitation, ■ negligence, strict liability or otherwise) for loss of sales, revenues or profits; cost of ■ May cause skin irritation upon contact, especially capital or funds; business interruption or cost of downtime, loss of use, damage to prolonged or repeated. If skin contact occurs, wash or loss of use of other property (real or personal); failure to realize expected savings; frustration of economic or business expectations; claims by third parties (other than immediately with soap and water and seek medical help for bodily injury), or economic losses of any kind; or for any special, incidental, indirect, consequential, punitive or exemplary damages arising in any way out of the as needed performance of, or failure to perform, its obligations under any contract for sale of product, even if Dayton could foresee or has been advised of the possibility of such ■■ If eye contact occurs, flush immediately with clean water damages. The Parties expressly agree that these limitations on damages are allocations of risk constituting, in part, the consideration for this contract, and also that such and seek medical help as needed limitations shall survive the determination of any court of competent jurisdiction that ■■ Dispose of waste material in accordance with federal, state any remedy provided in these terms or available at law fails of its essential purpose. and local requirements

® 10/07/11 • Page 2 of 2

11-8 Visit www.daytonsuperior.com for the most up to date technical information ® AggreGloss™ Satin J25S ® Concrete Sealer

TECHNICAL DATA SHEET Sec

DESCRIPTION STORAGE 11 AggreGloss™ Satin J25S is a formulation of 25% methacrylate Store material in a horizontal position to prevent moisture copolymers in an aromatic solvent. AggreGloss™ Satin J25S is accumulation on the drum head. a clear sealer that will not yellow under exposure to sunlight. The AggreGloss™ Satin J25S forms a tenacious bond to the Shelf life is 24 months from date of manufacture in unopened concrete surface and provides a long lasting, low gloss, satin containers. Do not store below 0°F (-18°C). film. APPLICATION USE Surface Preparation: Surface must be clean, dry, free of grease, AggreGloss™ Satin J25S will seal, dustproof and enhance dirt, paint and effloresence (white residue). If the substrate is

the beauty of new and old concrete. It is a film forming sealer wet from the rain or from surface cleaning, wait a minimum of Sealers for concrete, stamped concrete, exposed aggregate concrete or 24 hours to allow the surface to dry completely before applying. pavers. AggreGloss™ Satin J25S allows the substrate to breathe Repair all defects prior to sealing. Protect or avoid spraying while protecting it from rain and airborne contaminants. AggreGloss™ Satin J25S on glass or metal.

FEATURES Placement: Apply AggreGloss™ Satin J25S with low pressure ■■ Protects against rain spray, roller or brush. Apply uniformly without interruption to ■■ Non-yellowing prevent streaking. Hold sprayer nozzle perpendicular to the ■■ Excellent adhesion to substrate surface and overlap each coat. In order to reduce loss of material ■■ Inhibits attack by airborne contaminants to the atmosphere, avoid high pressures when spraying and ■■ Breathable film too fine a spray. Ensure spray nozzle is allowing for a uniform ■■ Satin finish spray pattern without tailings or drips. Coverage will vary with ■■ Resists mildew and surface staining the density and texture of the surface. Apply the AggreGloss™ ■■ Inhibits efflorescence Satin J25S to achieve a complete, uninterrupted film. Avoid applications that are too heavy or too light. Heavy coats can PROPERTIES: bubble and reduce moisture vapor transmission. Too light of Dry time: Approx. 2 hours at 70°F (21°C) for re-coating or light an application may not allow material to form a complete traffic. Wait 12 hours for heavy traffic Dry time is temperature, film. Avoid application during excessively hot air or substrate humidity and wind dependent temperatures (>90˚F, 32.2˚C).

ESTIMATING GUIDE CLEAN UP Approximate Coverage Rates: For tools and equipment use Xylol or lacquer thinner. Sq. Ft./Gal Sq M/Liter 1st coat 200 – 300 4.9 – 7.4 LIMITATIONS 2nd coat 400 – 600 9.8 – 14.8 FOR PROFESSIONAL USE ONLY For applications of a sealer in an enclosed structure, Dayton Texture and absorption rate of the concrete will influence Superior recommends a water based product like the Ultra Seal coverage rate. Two coats of AggreGloss™ Satin J25S are EF. recommended. Allow the first coat to dry before applying the Sprayers and equipment should have neoprene or viton type second coat. hose and gaskets. PACKAGING Allow 24 hours after rain before application. ITEM # PACKAGE SIZE Do not apply at temperatures below 40°F ( 4 °C) or when the Gallons Liters average daily temperature remains below 40°F (4°C). 305646 Pail 5 18.93 AggreGloss™ Satin J25S is not intended for areas subject to high abrasion, such as bridge decks and roadways. Do not use AggreGloss™ Satin J25S on bituminous surfaces, staining will result.

American Owned American Made 10/07/11 • Page 1 of 2

Visit www.daytonsuperior.com for the most up to date technical information 11-9 ™ TECHNICAL DATA SHEET AggreGloss Satin J25S CONTINUED Concrete Sealer

Will interfere with the adhesion of sealants, thus avoid spraying MANUFACTURER Sec AggreGloss™ Satin J25S into a joint prior to installation of Dayton Superior Corporation sealant. 1125 Byers Road 11 Miamisburg, OH 45342

Sealers Apply to concrete that is a minimum of 7 days old. Customer Service: 888-977-9600 Not for use under resinous (epoxy, polyester, urethane, etc.) Technical Services: 866-329-8724 coatings. Website: www.daytonsuperior.com Film may show black rubber tire marks. WARRANTY Not resistant to gas, oil, brake fluid, etc. Dayton Superior Corporation (“Dayton”) warrants for 12 months from the date of manufacture or for the duration of the published product shelf life, whichever is less, that at the time of shipment by Dayton, the product is free of manufacturing defects Will darken color of concrete surfaces and conforms to Dayton’s product properties in force on the date of acceptance by Dayton of the order. Dayton shall only be liable under this warranty if the product has been applied, used, and stored in accordance with Dayton’s instructions, especially surface preparation and installation, in force on the date of acceptance by Dayton of PRECAUTIONS the order. The purchaser must examine the product when received and promptly notify READ MSDS PRIOR TO USING PRODUCT Dayton in writing of any non-conformity before the product is used and no later than 30 days after such non-conformity is first discovered. If Dayton, in its sole discretion, ■■ Keep material and containers away from high heat, open determines that the product breached the above warranty, it will, in its sole discretion, replace the non-conforming product, refund the purchase price or issue a credit in the flames, sparks or other sources of ignition amount of the purchase price. This is the sole and exclusive remedy for breach of this warranty. Only a Dayton officer is authorized to modify this warranty. The information ■■ Use with adequate ventilation in this data sheet supersedes all other sales information received by the customer ■■ Wear protective clothing, gloves and eye during the sales process. THE FOREGOING WARRANTY SHALL BE EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES protection (Goggles, Safety Glasses and/or Face Shield) OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND ALL OTHER WARRANTIES OTHERWISE ARISING BY OPERATION OF LAW, COURSE OF DEALING, ■■ Keep out of the reach of children CUSTOM, TRADE OR OTHERWISE.

■■ Do not take internally Dayton shall not be liable in contract or in tort (including, without limitation, ■ negligence, strict liability or otherwise) for loss of sales, revenues or profits; cost of ■ In case of ingestion, seek medical help immediately capital or funds; business interruption or cost of downtime, loss of use, damage to ■■ May cause skin irritation upon contact, especially or loss of use of other property (real or personal); failure to realize expected savings; frustration of economic or business expectations; claims by third parties (other than prolonged or repeated. If skin contact occurs, wash for bodily injury), or economic losses of any kind; or for any special, incidental, indirect, consequential, punitive or exemplary damages arising in any way out of the immediately with soap and water and seek medical help performance of, or failure to perform, its obligations under any contract for sale of product, even if Dayton could foresee or has been advised of the possibility of such as needed damages. The Parties expressly agree that these limitations on damages are allocations ■ of risk constituting, in part, the consideration for this contract, and also that such ■ If eye contact occurs, flush immediately with clean water limitations shall survive the determination of any court of competent jurisdiction that and seek medical help as needed any remedy provided in these terms or available at law fails of its essential purpose. ■■ Dispose of waste material in accordance with federal, state and local requirements

® 10/07/11 • Page 2 of 2

11-10 Visit www.daytonsuperior.com for the most up to date technical information ® Anti Spall J33 ® Concrete Sealer

TECHNICAL DATA SHEET Sec

DESCRIPTION PACKAGING 11 A uniform blend of mineral spirits and boiled linseed oil used for ITEM # PACKAGE SIZE protecting exterior concrete. The Anti Spall J33 has a light amber Gallons Liters color. 69180 Pail 5 18.93 USE 69179 Drum 55 208.20 Anti Spall J33 protects new and old concrete surfaces from progressive deterioration caused by freeze/thaw cycles and STORAGE deicing salts. It is specially formulated to resist the penetration Store material in a horizontal position to prevent moisture of water and deicing salts. accumulation on the drum head. Sealers Anti Spall J33 is especially effective for providing maximum first- Shelf life is 24 months from date of manufacture in unopened winter protection on newly placed concrete and is also effective containers. for protecting older concrete surfaces. It is an ideal product for use on bridge decks, bridge superstructures, highways, parking APPLICATION garages, and concrete barrier rails, loading areas, runways, and Surface Preparation: Surfaces should be clean of all dirt, oil, many exterior concrete surfaces. grease, curing compounds and other substances that would prevent proper penetration of the material. Prior to application, FEATURES the surface should be thoroughly dry. Wait a minimum of 24 ■■ Prolongs the life of concrete hours for a damp surface to dry out. New concrete should be ■■ Resists freeze/thaw cycles and deicing salts cured for a minimum of 14 days before application of the anti- ■■ Creates an effective barrier against the elements of spalling sealer (28 days is preferred). weather ■■ Applies easily – by spray, roller or broom Placement: Application can be by tank sprayer, broom, roller ■■ Dries quickly or the use of spray bars for the larger jobs. Two coats are ■■ Provides protection for new and old concrete surfaces recommended. DO NOT OVER APPLY. ANY EXCESS OR PUDDLES OF MATERIAL MUST BE REMOVED WITH RAGS OR PAINT PROPERTIES ROLLER. Do not apply in temperatures below 40°F (4°C). Meets AASHTO M-233-86, standard specification for: “Boiled For maximum protection, apply Anti Spall J33 onto the concrete Linseed Oil Mixture for Treatment of Portland Cement Concrete.” surface before it is exposed to deicing salts. Protect the spray (AASHTO M-126 and M-128 have been discontinued). from accidentally hitting nearby cars, buildings, grass and shrubs. Boiled linseed oil meets ASTM Specification D-260 and Federal Specification TT-L-190-d. Mineral Spirits meets ASTM CLEAN UP Specification D-235 and Federal Specification TT- L-291 -c. Tools and equipment: use mineral spirits, naphtha or xylene. Formulations will conform to most state specifications for anti- spalling compounds. LIMITATIONS FOR PROFESSIONAL USE ONLY Dry time: Approx. 2 hours at 70°F (21°C) for re-coating or light Product will turn the concrete to a dark amber color. traffic. Wait 12 hours for heavy traffic Dry time is temperature, Do not over apply the product because a slippery or tacky humidity and wind dependent surface may result.

VOC Use less material on a dense or smooth troweled concrete Complies with U.S. EPA requirements with less than 400 g/L surface. Do not apply in temperatures below 40°F (4°C) ESTIMATING GUIDE Coverage: Two coats are recommended. Apply the first coat at 350 sq. ft./gal. (8.6 sq m/L) When the first coat is dry to the touch, apply the second coat at 600 sq. ft /gal. (14.7 sq m/L). When the second coat is totally dry, the surface is ready for traffic. Texture and absorption of surface will influence final coverage rates.

American Owned American Made 10/07/11 • Page 1 of 2

Visit www.daytonsuperior.com for the most up to date technical information 11-11 TECHNICAL DATA SHEET Anti Spall J33 CONTINUED Concrete Sealer

PRECAUTIONS MANUFACTURER Sec READ MSDS PRIOR TO USING PRODUCT Dayton Superior Corporation ■■ Keep material and containers away from high heat, open 1125 Byers Road 11 flames, sparks or other sources of ignition Miamisburg, OH 45342 Sealers ■■ Use with adequate ventilation Customer Service: 888-977-9600 ■■ Wear protective clothing, gloves and eye Technical Services: 866-329-8724 protection (Goggles, Safety Glasses and/or Face Shield) Website: www.daytonsuperior.com ■■ Keep out of the reach of children ■■ Do not take internally WARRANTY Dayton Superior Corporation (“Dayton”) warrants for 12 months from the date of ■■ In case of ingestion, seek medical help immediately manufacture or for the duration of the published product shelf life, whichever is less, ■ that at the time of shipment by Dayton, the product is free of manufacturing defects ■ May cause skin irritation upon contact, especially and conforms to Dayton’s product properties in force on the date of acceptance by prolonged or repeated. If skin contact occurs, wash Dayton of the order. Dayton shall only be liable under this warranty if the product has been applied, used, and stored in accordance with Dayton’s instructions, especially immediately with soap and water and seek medical help surface preparation and installation, in force on the date of acceptance by Dayton of the order. The purchaser must examine the product when received and promptly notify as needed Dayton in writing of any non-conformity before the product is used and no later than 30 days after such non-conformity is first discovered. If Dayton, in its sole discretion, ■■ If eye contact occurs, flush immediately with clean water determines that the product breached the above warranty, it will, in its sole discretion, replace the non-conforming product, refund the purchase price or issue a credit in the and seek medical help as needed amount of the purchase price. This is the sole and exclusive remedy for breach of this ■■ Dispose of waste material in accordance with federal, state warranty. Only a Dayton officer is authorized to modify this warranty. The information in this data sheet supersedes all other sales information received by the customer and local requirements during the sales process. THE FOREGOING WARRANTY SHALL BE EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND ALL OTHER WARRANTIES OTHERWISE ARISING BY OPERATION OF LAW, COURSE OF DEALING, CUSTOM, TRADE OR OTHERWISE.

® 10/07/11 • Page 2 of 2

11-12 Visit www.daytonsuperior.com for the most up to date technical information ® Tuf Seal™ J35 ® Concrete Sealer

TECHNICAL DATA SHEET Sec

DESCRIPTION STORAGE 11 Tuf Seal™ J35 is a scientifically formulated clear, non-yellowing Store material in a horizontal position to prevent moisture sealer comprised of methyl methacrylate polymers. It dries accumulation on the drum head. to a durable, high gloss finish that not only protects, but also beautifies floors. Tuf Seal™ J35 is designed to provide protection Shelf life is 24 months from date of manufacture in unopened from oil and gasoline and excellent resistance to oils, greases containers. Do not store below 0°F (-18°C). and weathering. APPLICATION USE Surface Preparation: Surface must be clean, dry, free of grease, Tuf Seal™ J35 will not only provide improved gasoline/oil dirt, paint and effloresence (white residue). If the substrate is

resistance, but it will also help to prevent dusting, spalling and wet from the rain or from surface cleaning, wait a minimum of Sealers inhibit efflorescence. Clean-up time is reduced and simplified 24 hours to allow the surface to dry completely before applying. since dirt, grease, oil that normally soak into the concrete are Repair all defects prior to sealing. Protect or avoid spraying Tuf easily removed from the coating. Tuf Seal™ J35 not only offers Seal™ J35 on glass or metal. protection for concrete surfaces, but it can also protect and beautify exposed aggregate and stamped concrete. Placement: Apply Tuf Seal™ J35 with low pressure spray, roller or brush. Apply uniformly without interruption to prevent FEATURES streaking. Hold sprayer nozzle perpendicular to the surface and ■■ High gloss finish overlap each coat. In order to reduce loss of material to the ■■ Easy to recoat – No extensive surface preparations atmosphere, avoid high pressures when spraying and too fine ■■ Resists gasoline, grease, and many oils a spray. Ensure spray nozzle is allowing for a uniform spray ■■ Non-yellowing, clear coating pattern without tailings or drips. Coverage will vary with the ■■ Reduces maintenance and clean-up time density and texture of the surface. Apply the Tuf Seal™ J35 to ■■ Excellent protection against the weather and ultraviolet achieve a complete, uninterrupted film. Avoid applications that radiation are too heavy or too light. Heavy coats can bubble and reduce ■■ USDA Approved for incidental food contact moisture vapor transmission. Too light of an application may not allow material to form a complete film. Avoid application during PROPERTIES excessively hot air or substrate temperatures (>90˚F, 32.2˚C). Dry time: Approx. 2 hours at 70°F (21°C) for re-coating or light traffic. Wait 12 hours for heavy traffic Dry time is temperature, CLEAN UP humidity and wind dependent For tools and equipment use xylol or lacquer thinner.

ESTIMATING GUIDE LIMITATIONS Approximate Coverage Rates: FOR PROFESSIONAL USE ONLY Sq. Ft./Gal Sq M/Liter For applications of a sealer in an enclosed structure, Dayton 1st coat 200 – 300 4.9 – 7.4 Superior recommends a water based product like the Ultra Seal EF. 2nd coat 400 – 600 9.8 – 14.8 Sprayers and equipment should have neoprene or viton type hose and gaskets. Texture and absorption rate of the concrete will influence coverage rate. Two coats of Tuf Seal™ J35 are recommended. Do not apply at temperatures below 40°F (4°C) or when the Allow the first coat to dry before applying the second coat. average daily temperature remains below 40°F (4°C). Apply to concrete that is a minimum of 7 days old. PACKAGING Will interfere with the adhesion of sealants, thus avoid spraying ITEM # PACKAGE SIZE Tuf Seal™ J35 into a joint prior to installation of sealant. Gallons Liters Product intended for incidental or short term chemical contact; 69078 Unit (36 min.) 1 3.79 for long term exposure applications contact Dayton Superior 69077 Pail 5 18.93 technical services. 69076 Drum 55 208.20 Tuf Seal™ J35 will not resist brake or hydraulic fluids.

American Owned American Made 10/07/11 • Page 1 of 2

Visit www.daytonsuperior.com for the most up to date technical information 11-13 ™ TECHNICAL DATA SHEET Tuf Seal J35 CONTINUED Concrete Sealer

Not for use under resinous (epoxy, polyester, urethane, etc.) MANUFACTURER Sec coatings. Dayton Superior Corporation Film may show black rubber tire marks. 1125 Byers Road 11 Miamisburg, OH 45342 Sealers Will darken color of concrete surfaces Customer Service: 888-977-9600 Technical Services: 866-329-8724 PRECAUTIONS Website: www.daytonsuperior.com READ MSDS PRIOR TO USING PRODUCT ■■ Keep material and containers away from high heat, open WARRANTY Dayton Superior Corporation (“Dayton”) warrants for 12 months from the date of flames, sparks or other sources of ignition manufacture or for the duration of the published product shelf life, whichever is less, that at the time of shipment by Dayton, the product is free of manufacturing defects ■■ Use with adequate ventilation and conforms to Dayton’s product properties in force on the date of acceptance by ■ Dayton of the order. Dayton shall only be liable under this warranty if the product has ■ Wear protective clothing, gloves and eye been applied, used, and stored in accordance with Dayton’s instructions, especially protection (Goggles, Safety Glasses and/or Face Shield) surface preparation and installation, in force on the date of acceptance by Dayton of the order. The purchaser must examine the product when received and promptly notify ■■ Keep out of the reach of children Dayton in writing of any non-conformity before the product is used and no later than 30 days after such non-conformity is first discovered. If Dayton, in its sole discretion, ■■ Do not take internally determines that the product breached the above warranty, it will, in its sole discretion, replace the non-conforming product, refund the purchase price or issue a credit in the ■■ In case of ingestion, seek medical help immediately amount of the purchase price. This is the sole and exclusive remedy for breach of this ■■ May cause skin irritation upon contact, especially warranty. Only a Dayton officer is authorized to modify this warranty. The information in this data sheet supersedes all other sales information received by the customer prolonged or repeated. If skin contact occurs, wash during the sales process. THE FOREGOING WARRANTY SHALL BE EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES immediately with soap and water and seek medical help OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND ALL OTHER WARRANTIES OTHERWISE ARISING BY OPERATION OF LAW, COURSE OF DEALING, as needed CUSTOM, TRADE OR OTHERWISE. ■ ■ If eye contact occurs, flush immediately with clean water Dayton shall not be liable in contract or in tort (including, without limitation, and seek medical help as needed negligence, strict liability or otherwise) for loss of sales, revenues or profits; cost of capital or funds; business interruption or cost of downtime, loss of use, damage to ■■ Dispose of waste material in accordance with federal, state or loss of use of other property (real or personal); failure to realize expected savings; frustration of economic or business expectations; claims by third parties (other than and local requirements for bodily injury), or economic losses of any kind; or for any special, incidental, indirect, consequential, punitive or exemplary damages arising in any way out of the performance of, or failure to perform, its obligations under any contract for sale of product, even if Dayton could foresee or has been advised of the possibility of such damages. The Parties expressly agree that these limitations on damages are allocations of risk constituting, in part, the consideration for this contract, and also that such limitations shall survive the determination of any court of competent jurisdiction that any remedy provided in these terms or available at law fails of its essential purpose.

® 10/07/11 • Page 2 of 2

11-14 Visit www.daytonsuperior.com for the most up to date technical information ® Tuf Seal™ Satin J35S ® Concrete Sealer

TECHNICAL DATA SHEET Sec

DESCRIPTION STORAGE 11 Tuf Seal™ Satin J35S is a scientifically formulated clear, non- Store material in a horizontal position to prevent moisture yellowing sealer comprised of methyl methacrylate polymers. accumulation on the drum head. It dries to a durable, satin finish that not only protects, but also Shelf life is 24 months from date of manufacture in unopened beautifies floors. Tuf Seal™ Satin J35S is designed to provide containers. Do not store below 0°F (-18°C). protection from oil and gasoline and excellent resistance to oils, greases and weathering. APPLICATION Surface Preparation: Surface must be clean, dry, free of grease, USE dirt, paint and effloresence (white residue). If the substrate is Tuf Seal™ Satin J35S will not only provide improved gasoline/oil wet from the rain or from surface cleaning, wait a minimum of

resistance, but it will also help to prevent dusting, spalling and 24 hours to allow the surface to dry completely before applying. Sealers inhibit efflorescence. Clean-up time is reduced and simplified Repair all defects prior to sealing. Protect or avoid spraying Tuf since dirt, grease, oil that normally soak into the concrete are Seal™ Satin J35S on glass or metal. easily removed from the coating. Tuf Seal™ Satin J35S not only offers protection for concrete surfaces, but it can also protect Mixing: Thoroughly mix the product prior to each use. and beautify exposed aggregate and stamped concrete. Placement: Apply Tuf Seal™ Satin J35S with low pressure spray, FEATURES roller or brush. Apply uniformly without interruption to prevent ■■ Satin finish streaking. Hold sprayer nozzle perpendicular to the surface and ■■ Easy to recoat – No extensive surface preparations overlap each coat. In order to reduce loss of material to the ■■ Resists gasoline, grease, and many oils atmosphere, avoid high pressures when spraying and too fine a ■■ Non-yellowing, clear coating spray. Ensure spray nozzle is allowing for a uniform spray pattern ■■ Reduces maintenance and clean-up time without tailings or drips. Coverage will vary with the density ■■ Excellent protection against the weather and ultraviolet and texture of the surface. Apply the Tuf Seal™ Satin J35S to radiation achieve a complete, uninterrupted film. Avoid applications that ■■ USDA Approved for incidental food contact are too heavy or too light. Heavy coats can bubble and reduce moisture vapor transmission. Too light of an application may not PROPERTIES allow material to form a complete film. Avoid application during Dry time: Approx. 2 hours at 70°F (21°C) for re-coating or light excessively hot air or substrate temperatures (>90˚F, 32.2˚C). traffic. Wait 12 hours for heavy traffic Dry time is temperature, humidity and wind dependent CLEAN UP . For tools and equipment use xylol or lacquer thinner. ESTIMATING GUIDE Approximate Coverage Rates: LIMITATIONS Sq. Ft/Gal Sq M/Liter FOR PROFESSIONAL USE ONLY 1st coat 200 – 300 4.9 – 7.4 For applications of a sealer in an enclosed structure, Dayton 2nd coat 400 – 600 9.8 – 14.8 Superior recommends a water based product like the Ultra Seal EF. Sprayers and equipment should have neoprene or viton type Texture and absorption rate of the concrete will influence hose and gaskets. coverage rate. Two coats of Tuf Seal™ Satin J35S are recommended. Allow the first coat to dry before applying the Do not apply at temperatures below 40°F (4°C) or when the second coat. average daily temperature remains below 40°F (4°C). Apply to concrete that is a minimum of 7 days old. PACKAGING Will interfere with the adhesion of sealants, thus avoid spraying ITEM # PACKAGE SIZE Tuf Seal™ Satin J35S into a joint prior to installation of sealant. Gallons Liters Product intended for incidental or short term contact; for long 68078 Unit (36 min.) 1 3.79 term exposure applications contact Dayton Superior technical 68077 Pail 5 18.93 services. 68076 Drum 55 208.20 Tuf Seal™ Satin J35S will not resist brake or hydraulic fluids.

American Owned American Made 10/07/11 • Page 1 of 2

Visit www.daytonsuperior.com for the most up to date technical information 11-15 ™ TECHNICAL DATA SHEET Tuf Seal Satin J35S CONTINUED Concrete Sealer

® 10/07/11 • Page 2 of 2

11-16 Visit www.daytonsuperior.com for the most up to date technical information ® Ultra Seal EF ® Earth Friendly Concrete Sealer

TECHNICAL DATA SHEET Sec

DESCRIPTION REAGENT - Stain Resistance (One Hour Exposure) 11 Ultra Seal EF is an Earth Friendly (EF) acrylic, non-yellowing Ketchup Excellent (no effect) concrete sealer that may contribute to LEED Credits. The Ultra Mustard Excellent (no effect) Seal EF formula is low odor and contains VOC < 100 g/L, making “Kool-Aid” Excellent (no effect) it VOC compliant in all areas. The Ultra Seal EF is designed to Grape Juice Excellent (no effect) seal, protect and add an attractive gloss to existing concrete and Coffee Excellent (no effect) decorative concrete surfaces. Ultra Seal EF is blush resistant and Chocolate Syrup Excellent (no effect) has good resistance to common chemicals such as motor oil, Tincture of Iodine Poor antifreeze, vinegar and bleach. Coal Tar Poor

USE Chemical Resistance - (One Hour Exposure with no Sealers Ultra Seal EF can be used on all existing concrete and decorative Evaporation) concrete surfaces where a glossy, film forming sealer is desired. Used Motor Oil Excellent (no effect) Ultra Seal EF is non-yellowing making it suitable for both interior DI Water Excellent (no effect) and exterior applications. This ultra low VOC sealer can be used 10% Sodium Hydroxide Excellent (no effect) in all VOC restricted areas in the United States and Canada. 10% Sodium Chloride Excellent (no effect) 10% Calcium Chloride Excellent (no effect) FEATURES 3% Trisodium Phosphate Excellent (no effect) ■■ May Contribute to LEED Credits 10% Ammonia Excellent (no effect) ■■ Earth Friendly (EF) 10% Hydrochloric Acid Fair ■■ VOC Compliant in All Regions Brake Fluid Poor ■■ Resists Blushing, Hazing or Whitening 100 proof alcohol Poor ■■ Ultra UV Stable, Non-yellowing Gasoline Poor ■■ Attractive Gloss Finish Skydrol Poor ■■ High End Decorative Appearance ■■ Low Odor COLOR: ■■ Excellent Weatherability Milky white liquid that dries clear. ■■ Easy Spray/Roll Application ■■ Non-Flammable VOC ■■ Safe to Use & Store Actual VOC = 95 g/L. Compliant with all US VOC regulations for sealers including Federal EPA, OTC, LADCO, SCAQMD & CARB. PROPERTIES Dry Time: Approximately 2-3 hours @ 70˚F (21˚C) for recoating ESTIMATING GUIDE or light foot traffic. Wait 12 hours for heavy traffic. Dry time is 200 - 300 sq. ft./gallon (4.9-7.4 sq m/L) per application, 2 temperature, humidity and wind dependent applications recommended.

Moisture Vapor Transmission, ASTM D1653 A: 40 g/sq m /24 PACKAGING hours ITEM # PACKAGE SIZE Gallons Liters Accelerated Weathering: ASTM G53: Non-Yellowing after 4000 309249 Jug (36 min.) 1 3.79 Hours QUV 308690 Pail 5 18.93 CHEMICAL RESISTANCE 308691 Drum 55 208.20 Results based upon lab testing for splash, spillage and intermittent contact. Clean up all contaminants as soon as possible to avoid staining. A mock up sample is recommended to determine suitability of resistance for any particular application.

American Owned American Made 10/07/11 • Page 1 of 2

Visit www.daytonsuperior.com for the most up to date technical information 11-17 TECHNICAL DATA SHEET Ultra Seal EF CONTINUED Earth Friendly Concrete Sealer

STORAGE Sec KEEP FROM FREEZING. Shelf life is 18 months from date of 11 manufacture in original unopened containers. Sealers APPLICATION Surface Preparation: Substrates should be clean, free of all PRECAUTIONS READ MSDS PRIOR TO USING PRODUCT debris and contaminates and thoroughly dry. Newly placed ■■ Use with adequate ventilation concrete, toppings or overlayments must be cured 24-48 hours ■■ Wear protective clothing, gloves and eye from time of completed installation, depending on ambient protection (Goggles, Safety Glasses and/or Face Shield) conditions, substrate and mix design. Longer curing times are ■■ Keep out of the reach of children required in cool, damp conditions. Concrete curing compounds, if ■■ Do not take internally used, must be removed prior to application of sealer. Extremely ■■ In case of ingestion, seek medical help immediately slick, dense substrates may require abrasion prior to application ■■ May cause skin irritation upon contact, especially to achieve adequate adhesion of sealer. prolonged or repeated. If skin contact occurs, wash immediately with soap and water and seek medical help Mixing: Ultra Seal EF should be thoroughly mixed prior to as needed application. Do not thin or dilute. ■■ If eye contact occurs, flush immediately with clean water and seek medical help as needed Placement: Apply the Ultra Seal EF by brush, roller or spray. For ■■ Dispose of waste material in accordance with federal, state improved application consistency and reduction in labor, use and local requirements the Dayton Spray-Pro (Item # 309233 or 309232) power spray system. Uniformly apply the Ultra Seal EF at 200 -300 sq. ft./ MANUFACTURER gallon (4.9- 7.4 sq m/L) per application. Allow the Ultra Seal EF Dayton Superior Corporation to dry then uniformly apply a second coat of sealer at the same 1125 Byers Road coverage rate. Ensure application is uniform and a complete Miamisburg, OH 45342 film over the entire surface has been achieved. Do not apply the Customer Service: 888-977-9600 sealer applications too heavy or too light per coat. Light coats do Technical Services: 866-329-8724 not form a complete film, while heavy coats will extend the dry Website: www.daytonsuperior.com time and could discolor or peel. In general, two light mist coats are more effective than one heavy single coat. Re-application WARRANTY can take place as soon as the previous coat has dried. Protect Dayton Superior Corporation (“Dayton”) warrants for 12 months from the date of manufacture or for the duration of the published product shelf life, whichever is less, the application from rain, snow or excessive moisture for 24 that at the time of shipment by Dayton, the product is free of manufacturing defects and conforms to Dayton’s product properties in force on the date of acceptance by hours. Dayton of the order. Dayton shall only be liable under this warranty if the product has been applied, used, and stored in accordance with Dayton’s instructions, especially surface preparation and installation, in force on the date of acceptance by Dayton of CLEAN UP the order. The purchaser must examine the product when received and promptly notify Dayton in writing of any non-conformity before the product is used and no later than Clean tools, equipment and wet material with clean water. 30 days after such non-conformity is first discovered. If Dayton, in its sole discretion, determines that the product breached the above warranty, it will, in its sole discretion, Dried material may be removed with Dayton Superior’s Green replace the non-conforming product, refund the purchase price or issue a credit in the amount of the purchase price. This is the sole and exclusive remedy for breach of this Bean Clean. warranty. Only a Dayton officer is authorized to modify this warranty. The information in this data sheet supersedes all other sales information received by the customer during the sales process. THE FOREGOING WARRANTY SHALL BE EXCLUSIVE AND IN LIMITATIONS LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND ALL OTHER FOR PROFESSIONAL USE ONLY WARRANTIES OTHERWISE ARISING BY OPERATION OF LAW, COURSE OF DEALING, Minimum ambient and surface temperature for application is CUSTOM, TRADE OR OTHERWISE. 45°F (7.2°C) during application and for a minimum of 24 hours Dayton shall not be liable in contract or in tort (including, without limitation, negligence, strict liability or otherwise) for loss of sales, revenues or profits; cost of after application. capital or funds; business interruption or cost of downtime, loss of use, damage to or loss of use of other property (real or personal); failure to realize expected savings; frustration of economic or business expectations; claims by third parties (other than Do not apply if rain, snow or excessive moisture is expected for bodily injury), or economic losses of any kind; or for any special, incidental, during application or within 24 hours after application. indirect, consequential, punitive or exemplary damages arising in any way out of the performance of, or failure to perform, its obligations under any contract for sale of product, even if Dayton could foresee or has been advised of the possibility of such Do not use as a wear layer for heavy traffic areas as black tire damages. The Parties expressly agree that these limitations on damages are allocations of risk constituting, in part, the consideration for this contract, and also that such marking and premature failure could occur. limitations shall survive the determination of any court of competent jurisdiction that any remedy provided in these terms or available at law fails of its essential purpose. Will interfere with the adhesion of sealants, thus avoid spraying Ultra Seal EF into a joint prior to installation of sealant. Not for use under resinous (epoxy, polyester, urethane, etc.) coatings.

® 10/07/11 • Page 2 of 2

11-18 Visit www.daytonsuperior.com for the most up to date technical information