DOCSLIB.ORG

Technical Explanation for Timers and Time Switches Time and Timers for Explanation Technical Output

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Technical Explanation for Timers and Time Switches Time and Timers for Explanation Technical Output Technical Explanation for Timers and Time Switches CSM_Timer_Timeswitch_TG_E_7_3 Introduction Sensors What Is a Timer? A Timer is a control device that outputs a signal at a preset time after an input signal is received. Timer Mechanisms Switches Safety Components Relays Control Components (3) Timing Section Measures the time and outputs a signal to the output section at specified time. (2) Input Section Receives signals from input Input Output Timing Section Section devices and outputs the Section signals to the timing section. (4) Output Section Outputs signals (1) Power Supply Section Power Supply to output devices. Supplies the applied voltage Section to the internal components. Settings and Indications of Timers Operating Modes of Timers Example for the H3CR-A The operating mode selector is in the upper-right corner on the Settings Automation Systems Motion / Drives H3CR-A. (1) (1) Time setting knob (5) (2) Time unit selector (4) (6) (3) Time range selector (4) Operating mode selector The operating mode determines the output method that is (3) (2) used when the set time has reached. The following four basic operating modes are the most Energy Conservation Support / A variety of time ranges can be set with the H3CR-A using Environment Measure Equipment Note the time unit selector and time range selector. commonly used. Indications ON-delay Operation (Mode A) The pointers on the Timer do not move along with time like the hands of a clock do. You cannot see the progression of time. OFF-delay Operation (Mode D) Therefore, two operation indicators are provided on the upper Operation left of the Timer to identify the timer status. Power Supplies / Modes (5) Run/Power Indicator (Green) In Addition Flicker Operation (Mode B) Run indicator: Indicates whether the time is being measured or the time has reached. Power indicator: Indicates whether power is being Interval Operation (Mode E) supplied to the Timer. Fundamentally, the indicators will be lit when the power is being supplied. However, they will flash when the time is Others being measured. (6) Output Indicator (Orange) Used to see the status of the output. Lit when a signal is output. Common 1 Technical Explanation for Timers and Time Switches ON-delay Operation Flicker Operation Sensors Input Input Time counted out t t t t t t t t t After t seconds Output Output Switches Safety Components Relays Control Components With ON-delay operation, the Timer receives an input and With flicker operation, an output repeatedly turns ON and OFF then an output signal is output by switching the Timer contacts at the set time after an input is received. after a set time delay. This name is used because there is a delay between when the Application: Automatic Control of Fountains input signal is received (i.e., turns ON) and when the output signal is output. ON-delay operation is the operating mode most often used for automated machines. The water is Application: Pushbutton Signals repeatedly released and stopped at When the pedestrian intervals of two pushbutton is pressed for a minutes. traffic signal, the signal light changes from red to green after a delay. Interval Operation Input Automation Systems Motion / Drives OFF-delay Operation t Output Input With interval operation, the output turns ON at the same time Time counted out t seconds as the input and the output turns OFF after a set time. Output Application: Amusement Park Rides With OFF-delay operation, the output turns ON at the same time as the input and then the output turns OFF when the Timer contacts switch after the set time has expired. The set Energy Conservation Support / time is calculated from when the input turns OFF. Environment Measure Equipment This name is used because there is a delay between when the input turns OFF and when the output turns OFF. Application: Car Ceiling Lights The ride operates for five minutes When you get in your car, the when 100 yen is ceiling light turns ON when the inserted. Power Supplies / door is opened. The light In Addition remains lit for several seconds after you get into the car and close the door. Others Common 2 Technical Explanation for Timers and Time Switches Timer Starting Methods There are two starting methods for the operating modes. Sensors Example: ON-delay Operation Signal ON-delay operation: Measuring time starts when the input section receives an input while voltage is being applied to the Timer power supply Switches Safety Components Relays Control Components section. Power ON-delay operation: Measuring time starts when voltage is applied to the Timer power supply section. Signal ON-delay Power ON-delay Power Power supply supply Input t t Output Output Differences between Signal ON-delay Operation and Power ON-delay Operation (1) Accuracy* Operation will not be stable unless a brief period elapses after the power supply is turned ON to the timing section of the Timer. Power supply start:Operation is unstable because measuring time starts at the same time that the power supply turns ON. Automation Systems Motion / Drives Therefore, deviation will occur in the operation time immediately after starting the Timer. Signal start: Stable time accuracy is ensured because a voltage is already applied to the Timer before starting the Timer. The accuracy of the signal start is generally considered better. For some models, however, such as the H3CR, there is no change in accuracy. *Accuracy is the correctness of the time. Energy Conservation Support / (2) Terminal Arrangement Environment Measure Equipment Signal start (H3CR-A) Power supply start (H3CR-A8) Reset input Start input Power Supplies / Gate input In Addition Power supply Power supply • Models with a signal start require three external inputs, so they have many terminals. • Models with a power supply start (H3CR-A8) are the H3CR Timers most often used for automated machinery. Others Common 3 Technical Explanation for Timers and Time Switches What Is a Time Switch? Sensors A Time Switch is a control device that turns a load ON and OFF at the set times. Time Switch Mechanisms Switches Safety Components Relays Control Components (3) Timing Section Measures the time and outputs a signal to the output section at specified time. (2) Input Section Receives signals from input Input Output Timing Section Section devices. Section (4) Output Section Outputs signals (1) Power Supply Section Power Supply to output devices. Supplies the applied voltage Section to the internal components. However, most models of Time Switches do not have an input section. If there is an input section, it is not used to output signals to the timing section, rather, it is used to control some of the functions of the Time Switch, such as adjusting the time. Settings and Indications of Time Switches Example for the H5F Automation Systems Motion / Drives Settings Display Present Day Indicator H5F TIME SWITCH SU MO TU WE TH FR SA Operation Day Indicator Lit: Operation day Not lit: Non-operation day A Mode Key Time Adjustment Mode Indicator Flashing: Specified SU MO TU WE TH FR SA operation day OUT POWER Displays the Present Time, Partial Operation on I Timer/Pulse B Hour Key OUT Operation Time, and Time Width Specified Day Indicator TMR/ P MODE h m/ P WD S output Key ON C AM s Minutes/Pulse Time Width Key m Pulse Width Unit Indicator H Output ON/OFF AUTO CLR SELECT d WRITE Output Indicator PM OFF D +1h Write Key Lit when control output is ON. ON P Summer Time Indicator Switch +1h HOLIDAY TEST AM E Day Shift/Program Test Key Power Indicator PW PM P Lit when set to summer G Clear/Summer F Select/Holiday Key Lit when power is supplied time. Time Key to the Time Switch. Energy Conservation Support / Next Operation Environment Measure Equipment Operation Setting Indicators Mode Indicator No. Function Pulse Operation Indicator Lit: Pulse-output operation A Switches between time adjustment mode, the operation setting Not lit: Timer operation modes, and run mode. Run mode: Displays the direction (i.e., ON or OFF) and time B Sets hours or switches between 12-hour (am/pm) and 24-hour of the next output operation. display. Operation time setting mode: Displays the program number for the setting. Power Supplies / C In Addition Sets minutes or a pulse time width. Holiday setting mode: Displays hday (hday) when the Time Switch is in holiday setting mode. D Writes the set data to memory or confirms settings with the program check function. Program check: Displays test (test) during program check. E Moves the cursor to specify a day or starts the program check function. F Specifies or cancels a specified day or switches to holiday setting mode. G Deletes the set data and initializes the day of operation or sets/clears Others summer time. ON: Turns on the output regardless of the setting. AUTO: Turns on/off the output according to the setting. H OFF: Turns off the output regardless of the setting. Override and automatic return operation can be executed by using this key in combination with the Write Key. I Selects timer operation or pulse-output operation. Common 4 Technical Explanation for Timers and Time Switches Operating Modes of Time Switches Sensors The operating mode determines the ON/OFF output method Timer Operation (ON/OFF Operation) that is used for the set times. Timer Operation (ON/OFF Operation) Switches Safety Components Relays Control Components ON time OFF time Pulse-output Operation With timer operation, the Time Switch controls the output according to the set ON and OFF times. Forced ON/OFF Operation Operating Application 1: Warm-up Operation for Packing Machine Modes Program Example Override and Automatic Return Operation Warm-up Start of work.
Load more

Recommended publications
  • IC 555 Timer in the Contemporary World
    International Journal of Engineering and Advanced Technology (IJEAT) ISSN: 2249 – 8958, Volume -4 Issue-6, August 2015 An Imprint of IC 555 Timer in t he Contemporary World Nanditha Nandanavanam Abstract- The paper deals with the basic principle of IC 555 There is also a flip flop element which gives high output Timer, its working and its application in the present world. 555 when ‘S’ is high and ‘R’ is low. It gives low when ‘R’ is Timer is part and parcel of almost every electronics project. It is high and ‘S’ is low. versatile IC whose applications range from simply making a light blink on and off to pulse-width modulation. From the time of its Pin configuration invention, a myriad of several novel and unique circuits have been developed and presented in several trade, professional , and hobby publications. Keywords: Monostable mode, A stable mode, Oscillator, Speed Detector, Hygrometer, Invertor, Patents. I. INTRODUCTION IC 555 timer is an integrated circuit(IC) or a chip used for various electronic applications. The IC was designed in 1971 by Hans R. Camenzind under a contract to Signetics, which was later acquired by Philips. It has b een in wide use ever since. It wa s the very first commercial timer IC to be designed. IC 555 timer got its name from three 5 kilo ohm resistors connec ted in series voltage divider. A single IC consists of several transistors, resistors, capacitors, diodes, flip flops and other elements. It is a highly stable device for Fig. 2 Pin diagram generating accurate time delays or oscillation [8].
    [Show full text]
  • PLC Based Timer Controller for Multiple Machines
    International Journal of Emerging Technologies in Engineering Research (IJETER) Volume 4, Issue 8, August (2016) www.ijeter.everscience.org PLC Based Timer Controller for Multiple Machines T.Vignesh, Assistant professor/Project Guide/EEE, Jay Shriram Group of Institutions, India. N.Lakshmanakumar, S.Sethu, P.Kumarasamy, S.Gowthamraj UG Scholar /EEE Jay Shriram group of Institutions, India. Abstract – This paper describes the design and development of a 2. PROGRAMMABLE LOGIC CONTROLLER feedback control system that maintains the time of a process at a desired set point. The system consists of a PLC-based timer The Programmable Logic Controller (PLC) is a relatively new controller unit that provides input and output interfaces between technology that uses a computer to process the information. the PLC and the man machine interface and computer system. The control task is incorporated into a graphical program called The main difference from other computers is that PLCs are the Ladder Logic Diagram. Any control task modifications are armoured for severe conditions such as dust, moisture, heat, cold done by changing the program. Today, PLCs are used in many etc., and have the facility for extensive input/output (I/O) "real world" applications such as machining, packaging, arrangements. The paper will provide details about the timer material handling, automated assembly or countless other control unit, shows the implementation of the controller unit, and industrial processes. present test results. Index Terms – PLC, Ladder Language, Functional Block Basic PLCs are available on a single printed circuit board .They Diagram (FBD), Automation. are sometimes called single board PLCs or open frame PLCs.
    [Show full text]
  • Chapter 7 TIMERS, COUNTERS and T/C APPLICATIONS
    Chapter 7 TIMERS, COUNTERS and T/C APPLICATIONS Introduction Timers and counters are discussed in the same chapter since most rules apply to both. Timers and counters have been in existence for as long as relays and provide an important component in the development of logic. Timers were constructed in the past as an add-on device to relays slowing down the transition of the plunger from immediately opening or closing. The time delay was accomplished with a pneumatic bladder that allowed the air to escape either quickly or slowly depending on the setting of the timer. Quick was usually less than a second and slow was usually between 30 and 60 seconds. Setting this kind of timer was an inexact science and today's traffic lights are an example of the fickle nature of timers that seldom respond in exactly the same from day to day and year to year. For the first time, function blocks are introduced in the rung output position or coil position to provide timer and counter functions. Function blocks allow inputs from the left and pass power through to the right when the function is done or when various conditions are met. Either the timer has timed out or the counter has counted to the preset. Function block usage differs from manufacturer to manufacturer. Function blocks rely on a standard format to enter information about the counter or timer. All variables in the function block must be entered correctly before the device will operate. Some timers are referred to as retentive. Retentive refers to the device’s ability to remember its exact status such that when the circuit is again activated, the timer continues from the previous point.
    [Show full text]
  • Citizen 6840 Movement
    Setting Instructions for Movement Caliber 6840 Contents (click on a topic) 1) Outline 2) Main Components 3) Mode Change-Over 4) Before Using a) 0-Position Setting 5) How to Set and Operate Each Mode a) Setting the Time b) Using Race Mode 1 c) Using Race Mode 2 d) Using Race Mode 3 e) Setting the Timer f) Stopwatch (Chronograph) Operation g) Setting the Alarm h) Alarm Monitor in the Normal Time Mode i) All-Reset Function 6) Use of the Rotating Bezel 7) Specifications 8) Care of Your Timepiece. Return to Table of Contents 1. OUTLINE This is an analog multi-function quartz watch having eight operation modes that can be changed with the push button. Main Features Race 1: 10-minute graphic timer Auto-Chronograph after time up Repeated timer Race 2: 10, 5-minute graphic timer Auto-Chronograph after time up Race 3: 3-,5-,10-minute graphic timer Timer: 90-minute timer Chronograph Alarm 2. Main Components Return to Table of Contents Return to Table of Contents 3. MODE CHANGE OVER Push the (M)(lower right) button to switch between modes as shown below TME R-1 R-2 R-3 Normal Race 1 Race 2 Race 3 time mode ALM CHR TMR >0< Alarm Stop-Watch Timer Mode Mode Zero Position Mode Confirmation Note: Be sure to check the mode hand to ensure that the watch is set in the desired mode for use. Pressing the (M)(lower right) accidentally during operation may occur. 4. BEFORE USE Before use, follow the procedure below to ensure that all watch components are in proper working order.
    [Show full text]
  • Digital Electronics: Logic and Clocks
    DIGITAL ELECTRONICS: LOGIC AND CLOCKS LAB 9 INTRO: INTRODUCTION TO DISCRETE DIGITAL LOGIC, MEMORY, AND CLOCKS GOALS In this experiment, we will learn about the most basic elements of digital electronics, from which more complex circuits, including computers, can be constructed. Proficiency with new equipment and approaches: o Logic gates, memory circuits, digital clocks o Combining components & Boolean logic DEFINITIONS Duty cycle – percentage of time during one cycle that a system is active (+5V in the case of digital logic) Truth table – table that shows all possible input combinations and the resulting outputs of digital logic components Flip-flop - a circuit that has two stable states and can be used to store state information. Logic gates – a physical device that implements some Boolean logic operation DIGITAL CIRCUITS - GENERAL In almost all experiments in the physical sciences, the signals that represent physical quantities start out as analog waveforms. To display and analyze the information contained in these signals, they most often are converted into digital data. Often this is done inside a commercial instrument such as an oscilloscope or a lock-in amplifier, which is then connected to a computer through a digital interface. In other cases, data acquisition cards are added to a computer chassis, allowing analog signals to be input directly to the computer. Scientists usually buy their data acquisition equipment rather than build it, so they usually don’t have to know too much about the digital circuitry that makes it work. Almost all data are eventually analyzed digitally with a computer. Analog information can be translated into digital form by a device called an Analog-to-Digital Converter (A/D converter or ADC).
    [Show full text]
  • Schrack Timers & Monitoring Relays
    Timer Relays w Timer Relays Series ZR5 w Timer Relays Series ZR5 Page 96 w Timer Relays Series ZR4 w Timer Relays Series ZR4 w Timer Relays Series AMPARO w Timer Relays Series ZR6 Timer Relays Page 97 Timer Relays w Index Timer Relays Series ZR5 ........................................................................................... Page 98 Timer Relays Series ZR4 ........................................................................................... Page 107 Timer Relays Series AMPARO .................................................................................. Page 112 Timer Relays Series ZR6 ........................................................................................... Page 116 Timer Relays w Timer Relays Series ZR5 Page 98 ZR5E,R,ER ZR5MF ZR5B ZR5SD025 ZR5RT011 w Schrack-Info ZR5E0011 ZR5MF025 ZR5SD025 • 1 CO • Multi-function timer relay • 2 CO • Mode: "E" • 2 CO • Wide input voltage range • Multi-voltage 24-240 V AC/DC • Modes: "E", "R", "Ws", "Wa", "Es", "Wu" • Mode: "S" & "Bp" • In-line design • Multi-voltage 12-240 V AC/DC • Multi-voltage 12-240 V AC/DC • 17.5 mm component width • In-line design • In-line design ZR5R0011 • 35 mm component width • 35 mm component width • 1 CO ZR5RT011 ZR5B0011 • Mode: "R" • Timer function for emergency lighting • 1 CO tests • Multi-voltage 24-240 V AC/DC • Modes: " lp" & "li" • 1 CO • In-line design • Multi-voltage 12-240 V AC/DC • Integrated test switch • 17.5 mm component width • In-line design • Mode: "Ws" ZR5ER011 • 17.5 mm component width • 230 V AC • 1 CO ZR5B0025
    [Show full text]
  • Relay and Timer Specifications
    Technical Data Relay and Timer Specifications Bulletin Number 700 Topic Page Topic Page NEMA Industrial Relays 149 Summary of Changes 2 700-P Industrial Relays 151 General Information 3 700S-P and 700S-PK — Heavy-Duty Safety Control Relays 167 General Purpose Relays 9 700-N Industrial Relays 172 700-HA General-purpose Relay 12 700-R Sealed Switch Relays 176 700-HB Square Base Relay 22 700-RTC — Solid-State Timing Relay 181 700-HD Flange Mount Square Base Relay 28 IEC Control Relays 187 700-HF Square Base Relay 32 700-CF Control Relay 188 700-HC Miniature Ice Cube Relay 39 700S-CF Control Relays 207 700-HK Slim Line Relay 44 700-K Miniature Control Relays 212 700-HL Terminal Block Relay 50 Solid-state Relays 219 700-HLF Terminal Block Timing Relay 60 Solid-state Relay Glossary 221 700-HP Slim Line Relay 64 700-SC Ice Cube Relays 226 700-HJ Magnetic Latching Relay 71 700-SF Square Base Relays 231 700-HG Power Relay 75 700-SH Hockey Puck Relays 235 700-HHF Flange Mount Power Relay 80 700-SK Slim Line Relays 244 700-HTA Alternating Relay 83 General Purpose Electronic Timers and Counters 89 700-FE Economy Timing Relay 92 700-FS High Performance Timing Relay 96 700-HNC Miniature Timing Relay 103 700-HNK Ultra-Slim Timing Relay 109 700-HR Dial Timing Relays 116 700-HT Plug-in Timing Relay 128 700-HV Timing Relay 133 700-HX Multi-Function Digital Timing Relay 138 Relay and Timer Specifications Summary of Changes This publication contains new and updated information as indicated in the following table.
    [Show full text]
  • 0 to 60 Hour Start / Stop Timer
    Total solder points: 96 + 43 Difficulty level: beginner 1 2 3 4 5 advanced 0 TO 60 HOUR START / STOP TIMER K6200 Broad range mains operated start / stop timer. ILLUSTRATED ASSEMBLY MANUAL H6200IP-1 VELLEMAN NV Legen Heirweg 33 9890 Gavere Belgium Europe www.velleman.be www.velleman-kit.com Features & Specifications If you want to have a device switched off after a given time, then this timer is the device you are looking for. Thanks to its big range this timer can be installed just about everywhere, for switching off your TV and HI-FI, the lights in the stairwell, as a security timer for your automatic coffee-maker, as a dark room timer, for mak- ing a short chime signal... etc. For the latter application you can control the start/stop timer from a switching clock such as the K6000 for example. The rough setting (from a couple of seconds up to about 20 hours) is done using dip switches, while the fine tuning is achieved by turning a trimming potentiometer. The timer has push buttons for starting and untimely stopping and it further allows to control the circuit by relay or open collector (e.g. our 15 channel remote controlled receiver K8050). The circuit can be fed directly from the mains and is so compact that it fits in a standard adapter housing. Features: Relay output: 5A at 220V LED indication Setting range: from +/- 3 secs to +/- 60 hours Starts promptly when the start push button is pressed Can be operated from an external push button or relay Can be operated from an open collector output (*) Power supply: 24VAC/50mA, 220VAC.
    [Show full text]
  • Multi-Functional Timer Relay. User Manual
    TIMERS.SHOP Multi-functional Timer relay. User Manual V5.0 12/26/2017 http://timers.shop Table of Contents 1. Multifunctional Timer Relay description ........................................................................................................................ 3 2. Timer wiring diagram ...................................................................................................................................................... 4 2.1 Connecting 5amp timer ........................................................................................................................................... 4 2.2 Connecting 10amp positive output timer ............................................................................................................... 4 2.3 Connecting 10amp negative (sink) output timer .................................................................................................... 5 3. Understanding Timer Delay Relay Function.................................................................................................................... 5 4. Timer function table with charts ..................................................................................................................................... 6 5. Timer trigger. ................................................................................................................................................................ 16 5.1 Timer trigger operation with charts. ....................................................................................................................
    [Show full text]
  • Building a Timer Controller Circuit with Password Access
    Bachelor’s Thesis Electrical Engineering Thesis no: 2012/2013 Building a timer controller circuit With password access ZIKORA AZUBUIKE CHEKWUBE Contact Information: Author(s): ZIKORA AZUBUIKE CHEKWUBE Address: Gyllenstjärnas väg 13C, 371 40 Karlskrona E-mail: [email protected] University advisor(s): Carina Nilsson, MScEE Department/School name: School of Computing School of Computing Internet : www.bth.se/com BlekingeSchool of Institute Computing of Technology Phone : +46 455 38 50 00 SEBlekinge – 371 79 Institute Karlskrona of Technology Fax : +46 455 38 50 57 SwedenSE – 371 79 Karlskrona Sweden ABSTRACT The microcontroller and the coding is the heart of making a timer. The strategic release planning is gotten from the concept of how a door machine with password access functions. In this thesis project, all that has been studied in school such as circuit theory, electronics, digital design and microprocessors basic and programming course are combined to the success of this project. Therefore the objective is producing a practical knowledge of what has been studied which is the timer with password access. The method used was an inspiration gotten after reviewing many materials in some respective topic related to designing a timer. The particular method comes from creating an SPI Interface from the Programmer to the Microcontroller to Make Transferring More Convenient. The performance of the MCU, LCD and keypad was just as was expected in the software code and hardware also. The password is inputted, timer is set appropriately and timer runs till port is opened. To conclude, the result can be achieved in different method but this method was for an easy method for beginners.
    [Show full text]
  • Experiment 7 Digital Logic Devices and the 555 Timer Part a – Basic
    Electronic Instrumentation ENGR-4300 Fall 2006 Experiment 7 Experiment 7 Digital Logic Devices and the 555 Timer Purpose: In this experiment we address the concepts of digital electronics and look at the 555 timer, a device that uses digital devices and other electronic switching elements to generate pulses. Equipment Required: • Voltmeter (Rensselaer IOBoard) • Oscilloscope (Rensselaer IOBoard) • Function Generator (Rensselaer IOBoard) • +5V Power Supply (Rensselaer IOBoard) • 555 Timer IC Helpful links for this experiment can be found on the links page for this course: http://hibp.ecse.rpi.edu/~connor/education/EILinks.html#Exp7 Part A – Basic Logic Gates Background Digital logic gates: All digital logic gates are based on binary logic. Binary logic has two values, called TRUE and FALSE or LOGIC 1 and LOGIC 0 or ON and OFF or HIGH and LOW. The corresponding binary number can have two possible values, 1 and 0. Digital logic gates perform many common logic operations on binary signals, such as AND, OR, NOT, NAND, and NOR. The table in figure A-1 contains the common symbol for each type of gate, an expression for the function of the gate in Boolean algebra, and a truth table for the device. The truth table shows how the gate will behave for all possible combinations of digital inputs. K.A. Connor, Susan Bonner, and Schoch 1 Revised: 10/27/2006 Rensselaer Polytechnic Institute Troy, New York, USA Electronic Instrumentation ENGR-4300 Fall 2006 Experiment 7 Figure A-1 Figure A-1 (continued) Digital logic chips: In TTL digital electronic circuits, the representation of binary numbers in terms of voltages is about 5 volts for LOGIC 1 and about 0 volts for LOGIC 0.
    [Show full text]
  • Stopwatch and Timer Calibrations
    i ii mci \_anui auui id (2009 edition) Jeff C Gust Robert M. Graham Michael A. Lombardi [T Special Publication Ititutftitute of ind Technology 960-12 m.t of Commerce NIST Special Publication 960-12 Stopwatch and Timer Calibrations (2009 edition) Jeff C. Gust Richard J. Bagan, Inc. Robert M. Graham Sandia National Laboratories Michael A. Lombardi National Institute of Standards and Technology January 2009 U.S. Department of Commerce Carlos M. Gutierrez, Secretary National Institute of Standards and Technology Patrick D. Gallagher, Deputy Director Certain equipment, instruments or materials are identified in this paper in order to adequately specify the experimental details. Such identification does not imply recom- mendation by the National Institute of Standards and Technology nor does it imply the materials are necessarily the best available for the purpose. Official contribution of the National Institute of Standards and Technology; not subject to copyright in the United States. National Institute of Standards and Technology Special Publication 960-12 Natl. Inst. Stand. Technol. Spec. Publ. 960-12 80 pages (January 2009) CODEN: NSPUE2 U.S. GOVERNMENT PRINTING OFFICE WASHINGTON: 2009 For sale by the Superintendent of Documents U.S. Government Printing Office Internet: bookstore.gpo.gov Phone:(202) 512-1800 Fax:(202) 512-2250 Mail: Stop SSOP, Washington, DC 20402-0001 Foreword > FOREWORD Stopwatch and timer calibrations are perhaps the most common calibrations performed in the field of time and frequency metrology. Hundreds of United States laboratories calibrate many thousands of timing devices annually to meet legal and organizational metrology requirements. However, prior to the publication of the first edition of this guide in May 2004, no definitive text had existed on the subject.
    [Show full text]