155.3202. Single-Family Residence 1 (Rs-1)

Article 3: Zoning Districts Part 2 Residential Base Zoning Districts Section 155.3202 Single-Family Residence 1 (RS-1)

155.3202. SINGLE-FAMILY RESIDENCE 1 (RS-1)

A. PURPOSE TYPICAL BUILDING TYPE The Single-Family Residence 1 (RS-1) District is established and intended to accommodate primarily single -family dwelling s at low densities on lots greater than 12,000 square feet in area. The district also accommodates accessory dwelling units as well as limited nonresidential uses usually found in urban single -family neighborhoods, generally as Special Exceptions.

B. USE STANDARDS See Appendix A: Consolidated Use Table, and use-specific standards in Article 4: Use Standards.

C. INTENSITY AND DIMENSIONAL STANDARDS 1

Lot area, minimum (sq ft) 12,000 TYPICAL LOT PATTERN Lot width, minimum (ft) 90 2 Density, maximum (du/ac) See Comprehensive Plan 3 1,500 for up to 3 bedrooms, plus 100 Floor area per dwelling unit, minimum (sq ft) per additional bedroom Lot coverage, maximum (% of lot area) 30 Pervious area, minimum (% of lot area) 30 Height, maximum (ft) 35 Front yard setback, minimum (ft) 35 Street side yard setback, minimum (ft) 18 Setback from a waterway or canal, minimum (ft) 25 Interior side yard setback, minimum (ft) 10 Rear yard setback, minimum (ft) 20 Required Front Yard, Pervious Area, minimum (% of Required 50 Front Yard) Dimensional Standards for Accessory Structures See Accessory Use-Specific standards in Article 4: Part 3. NOTES: [sq ft = square feet; ft = feet; du/ac = dwelling units/acre] 1. See measurement rules and allowed exceptions/variations in Article 9: Part 4 . 2. 110 ft for a corner lot. 3. On land classified Residential by the Land Use Plan, maximum gross residential density may not exceed that established for the particular land use classification. TYPICAL DEVELOPMENT CONFIGURATION

Max h eight : 35 ’ Min interior side yard setback; 10’

Min rear yard setback: 20’ Min lot width: 90’

Min corner lot width : 110 ’ Min front yard setback: 35’ Min street side yard setback: 18’

SINGLE -FAMILY DWELLING Min lot area = 12,000 sq ft Min floor area = 1,500 sq ft Max lot coverage = 30%

Adopted September 2012, Amended Jan., Feb., and July 2013 City of Pompano Beach, Florida Page 3-4 Zoning Code Article 3: Zoning Districts Part 2 Residential Base Zoning Districts Section 155.3203 Single-Family Residence 2 (RS-2)

155.3203. SINGLE-FAMILY RESIDENCE 2 (RS-2)

A. PURPOSE TYPICAL BUILDING TYPE The Single-Family Residence 2 (RS-2) district is established and intended to accommodate primarily single- family dwellings at moderate densities on lots greater than 7,000 square feet in area. The district also accommodates accessory dwelling units as well as limited nonresidential uses usually found in urban single- family neighborhoods (e.g., parks, places of worship, golf courses), generally as Special Exceptions.

B. USE STANDARDS See Appendix A: Consolidated Use Table, and use-specific standards in Article 4: Use Standards.

C. INTENSITY AND DIMENSIONAL STANDARDS 1

Lot area, minimum (sq ft) 7,000 TYPICAL LOT PATTERN Lot width, minimum (ft) 70 Density, maximum (du/ac) See Comprehensive Plan 2 Floor area per dwelling unit, minimum (sq ft) 1,250 Lot coverage, maximum (% of lot area) 40 Pervious area, minimum (% of lot area) 30 Height, maximum (ft) 35 5 Front yard setback, minimum (ft) 25 Street side yard setback, minimum (ft) 15 Setback from a waterway or canal, minimum (ft) 25 3 Interior side yard setback, minimum (ft) 7.5 Rear yard setback, minimum (ft) 20 5 Required Front Yard, Pervious Area, minimum (% of Required 50 Front Yard) Dimensional Standards for Accessory Structures See Accessory Use-Specific standards in Article 4: Part 3. NOTES: [sq ft = square feet; ft = feet; du/ac = dwelling units/acre] 1. See measurement rules and allowed exceptions/variations in Article 3. On existing lot where rear yard abuts waterway or canal, setback equals 9:Part 4 . the existing rear yard depth if it is between 15 ft and 25 ft. 2. On land classified Residential by the Land Use Plan, maximum gross 4. On existing lot, setback equals the existing rear yard depth if it is residential density may not exceed that established for the particular land between 15 ft and 20 ft. use classification. 5. The maximum height may be increased to 40 feet where the lowest structural member of a building must be 14.5 feet or more above National Geodetic Vertical Datum of 1929 (N.G.V.D) TYPICAL DEVELOPMENT CONFIGURATION

Min rear yard setback: 20’

Min setback from waterway or Min interior side canal: 25’ yard setback:

Min front yard 7.5’ setback: 25’ Min street side yard setback: 15’ SINGLE -FAMILY DWELLING Min lot area = 7,000 sq ft Min lot width : 70’ Min floor area = 1,250 sq ft Max lot coverage = 40%

City of Pompano Beach, Florida Adopted Sept. 2012; Amended Jan. 2013, Feb. 2013, & July 2013 Zoning Code Page 3-5 Article 3: Zoning Districts Part 2 Residential Base Zoning Districts Section 155.3204 Single-Family Residence 3 (RS-3)

155.3204. SINGLE-FAMILY RESIDENCE 3 (RS-3)

A. PURPOSE TYPICAL BUILDING TYPE The Single-Family Residence 3 (RS-3) district is established and intended to accommodate primarily single -family dwelling s at moderate densities on lots greater than 6,000 square feet in area. The district also accommodates accessory dwelling units as well as limited nonresidential uses usually found in urban single -family neighborhoods,, generally as Special Exceptions.

B. USE STANDARDS See Appendix A: Consolidated Use Table, and use-specific standards in Article 4: Use Standards. C. INTENSITY AND DIMENSIONAL STANDARDS 1 Lot area, minimum (sq ft) 6,000 TYPICAL LOT PATTERN Lot width, minimum (ft) 60 Density, maximum (du/ac) See Comprehensive Plan 2 Floor area per dwelling unit, minimum (sq ft) 750 Lot coverage, maximum (% of lot area) 40 Pervious area, minimum (% of lot area) 30 Height, maximum (ft) 35 Front yard setback, minimum (ft) 25 Street side yard setback, minimum (ft) 15 Setback from a waterway or canal, minimum (ft) 25 Interior side yard setback, minimum (ft) 7 Rear yard setback, minimum (ft) 15 Required Front Yard, Pervious Area, minimum (% of Required 50 Front Yard) Dimensional Standards for Accessory Structures See Accessory Use-Specific standards in Article 4: Part 3. NOTES: [sq ft = square feet; ft = feet; du/ac = dwelling units/acre] 1. See measurement rules and allowed exceptions/variations in Article 9:Part 4 . 2. On land classified Residential by the Land Use Plan, maximum gross residential density may not exceed that established for the particular land use classification.

TYPICAL DEVELOPMENT CON FIGURATION

Max h eight : 35 ’

Min rear Min setback yard from setback: 15’ waterway Min interior or canal: 25’ side yard setback: 7’ Min front yard setback: 25’ Min street side Min lot width : 60’ SINGLE -FAMILY DWELLING yard setback: 15’ Min lot area = 6,000 sq ft Min floor area = 750 sq ft Max lot coverage = 40%

Adopted September 2012, Amended Jan., Feb., and July 2013 City of Pompano Beach, Florida Page 3-6 Zoning Code Article 3: Zoning Districts Part 2 Residential Base Zoning Districts Section 155.3205 Single-Family Residence 4 (RS-4)

155.3205. SINGLE-FAMILY RESIDENCE 4 (RS-4)

A. PURPOSE TYPICAL BUILDING TYPE The Single-Family Residence 4 (RS-4) district is established and intended to accommodate primarily single -family dwelling s at moderate densities on lots greater than 5,000 square feet in area. The district also accommodates accessory dwelling units and zero -lot-line development, as well as limited no nresidential uses usually found in urban single-family neighborhoods, generally as Special Exceptions.

B. USE STANDARDS See Appendix A: Consolidated Use Table, and use-specific standards in Article 4: Use Standards. C. INTENSITY AND DIMENSIONAL STANDARDS 1 Lot area, minimum (sq ft) 5,000 TYPICAL LOT PATTERN Lot width, minimum (ft) 50 Density, maximum (du/ac) See Comprehensive Plan 2 Floor area per dwelling unit, minimum (sq ft) 675 Lot coverage, maximum (% of lot area) 40 Pervious area, minimum (% of lot area) 30 Height, maximum (ft) 35 Front yard setback, minimum (ft) 25 Street side yard setback, minimum (ft) 15 Setback from a waterway or canal, minimum (ft) 25 3 Interior side yard setback, minimum (ft) 6 Rear yard setback, minimum (ft) 15 Required Front Yard, Pervious Area, minimum (% of Required Front 50 Yard) Dimensional Standards for Accessory Structures See Accessory Use-Specific standards in Article 4: Part 3. NOTES: [sq ft = square feet; ft = feet; du/ac = dwelling units/acre] 1. See measurement rules and allowed exceptions/variations in Article 9:Part 4 2. On land classified Residential by the Land Use Plan, maximum gross residential density may not exceed that established for the particular land use classification. 3. For developments with zero-lot-line single family dwellings, 0 ft along the zero lot line and 15 ft for the opposite interior side lot line.

TYPICAL DEVELOPMENT CONFIGURATION A SINGLE -FAMILY DWELLING B B. SINGLE -FAMILY DWELLING , ZERO -LOT LINE Min lot area = 5,000 sq ft A Min floor area = 525 sq ft Max lot coverage = 40% Max h eight : 35 ’

Min rear yard setback: 15’ Min interior side

yard setback opposite zero -lot- Min front Min interior line: 15’ yard side yard setback: 25’ setback: 6’

Min street side Min lot width : 50’ yard setback: 15’

City of Pompano Beach, Florida Adopted Sept. 2012; Amended Jan. 2013, Feb. 2013, & July 2013 Zoning Code Page 3-7 Article 3: Zoning Districts Part 2 Residential Base Zoning Districts Section 155.3206 Single-Family Residence Lesureville (RS-L)

155.3206. SINGLE-FAMILY RESIDENCE LESUREVILLE (RS-L)

A. PURPOSE TYPICAL BUILDING TYPE The Single-Family Residence Leisureville (RS-L) district is established and intended to accommodate primarily cluster developments containing single-family dwelling s at a density of one dwelling per 5,000 square feet of site area, and where the site area is held in common by all owners of dwellings in the devel opment. The district also accommodates accessory dwelling units and development-serving recreation facilities and community centers, as well places as of worship (as a Special Exception).

B. USE STANDARDS See Appendix A: Consolidated Use Table, and use-specific standards in Article 4: Use Standards. B. INTENSITY AND DIMENSIONAL STANDARDS 1 Gross site area per dwelling, minimum (sq ft) 5,000 TYPICAL LOT PATTERN Lot width. minimum (ft) n/a Density, maximum (du/ac) See Comprehensive Plan 2 Floor area per dwelling unit, minimum (sq ft) 600 Lot coverage, maximum (% of lot area) 35 Pervious area, minimum (% of lot area) 30 Height, maximum (ft) 35 Setback from street, minimum (ft) 15 3 Setback from another zoning district, minimum (ft) 15 Setback from a waterway or canal, minimum (ft) 25 Spacing between principal structures, minimum (ft) 10 4 Required Front Yard, Pervious Area, minimum (% of Required Front 50 Yard) Dimensional Standards for Accessory Structures See Accessory Use-Specific standards in Article 4: Part 3. NOTES: [sq ft = square feet; ft = feet; du/ac = dwelling units/acre] 1. See measurement rules and allowed exceptions/variations in Article 9:Part 4 . 2. On land classified Residential by the Land Use Plan, maximum gross residential density may not exceed that established for the particular land use classification. 3. 25 ft from a major a rterial street and for the garage door side of a dwelling (from any street). 4. Increased to 15 ft between a one -story structure and a two-story structure and 20 ft between structures with 2 or more stories each.

TYPICAL DEVELOPMENT CONFIGURATION

SINGLE -FAMILY DWELLING Max h eight : 35 ’ Min front yard Min lot area = 5,000 sq ft setback without Min floor area = 600 sq ft front garage Max lot coverage = 35% door: 15’

Min front yard setback with front garage door or from Min spacing between major arterial two two -story street: 25’ structures: 20’ Min spacing between one - Min spacing story and two - between two story one -story structures: 15’ structures: 10’

Adopted September 2012, Amended Jan., Feb., and July 2013 City of Pompano Beach, Florida Page 3-8 Zoning Code Article 3: Zoning Districts Part 2 Residential Base Zoning Districts Section 155.3207 Two-Family Residence (RD-1)

155.3207. TWO-FAMILY RESIDENCE (RD-1)

A. PURPOSE TYPICAL BUILDING TYPE The Two-Family Residence (RD-1) district is established and intended to accommodate primarily single- family dwelling s and two-family dwellings at moderate densities. The district also accommodates accessory dwelling units (with single-family dwellings) as well as limited nonresidential uses usually found in urban single -family neighborhoods (e.g., parks, places of worship, golf courses), generally as Special Exceptions.

Min rear yard setback: 25’

Min setback from waterway Min front yard or canal: 25’ setback: 25’ Min interior TWO -FAMILY DETACHED DWELLING side yard Min lot area SF = 7,000 sq ft setback: Min street side yard setback: 18’ Min lot area 2F = 8,000 sq ft 8’ Min floor area = 525 sq ft

Max lot coverage = 35%

City of Pompano Beach, Florida Adopted Sept. 2012; Amended Jan. 2013, Feb. 2013, & July 2013 Zoning Code Page 3-9 Article 3: Zoning Districts Part 2 Residential Base Zoning Districts Section 155.3208 Multiple-Family Residence 7 (RM-7)

155.3208. MULTIPLE-FAMILY RESIDENCE 7 (RM-7)

A. PURPOSE TYPICAL BUILDING TYPE The Multiple-Family Residence 7 (RM-7) district is established and intended to accommodate primarily multifamily dwellings (including townhouse development) at low to moderate densities. The district also accommodates single-family and two-family dwellings, zero-lot-line development, community residential homes, assisted living facilities, and continuing care retirement communities. Limited nonresidential uses are allowed as Special Exceptions.

B. USE STANDARDS See Appendix A: Consolidated Use Table, and use-specific standards in Article 4: Use Standards. C. INTENSITY AND DIMENSIONAL STANDARDS 1 2 Lot area, minimum (sq ft) 7,000 2 Lot width, minimum (ft) 60 TYPICAL LOT PATTERN Density, maximum (du/ac) 7 2,3 SF 950 2F 750 Floor area per dwelling unit, minimum (sq ft) Efficiency units: 500 MF Other units: 650 + 100 per BR>1 Lot coverage, maximum (% of lot area) 60 2 Pervious area, minimum (% of lot area) 25 2 Height, maximum (ft) 35 Front yard setback, minimum (ft) 25 2,4 Street side yard setback, minimum (ft) 8 Setback from a waterway or canal, minimum (ft) 25 Setback from a dune vegetation line, minimum (ft) 25 Interior side yard setback, minimum (ft) 8 2,5 Rear yard setback, minimum (ft) 10 Spacing between principal structures, minimum (ft) 25 Required Front Yard, Pervious Area, minimum (% of 50 (for Single Family Dwellings only) Required Front Yard) Dimensional Standards for Accessory Structures See Accessory Use-Specific standards in Article 4: Part 3. NOTES: [sq ft = square feet; ft = feet; du/ac = dwelling units/acre; SF = single-family dwelling; 2F = two-family dwelling; MF = multifamily dwelling; BR = bedroom] 1. See measurement rules and allowed exceptions/variations in Article 9:Part 4 . 2. For townhouse development, applies only to the development site as a whole, provided individual townhouse lots have a minimum area of 1,800 sq ft and a minimum width of 18 ft. 3. On land classified Residential by the Land Use Plan, maximum gross residential density may not exceed that established for the particular land use classification. 4. Those portions of a structure extending above a height of 20 feet shall be set back an additional 1 ft for each 4 ft (or major fraction thereof) the height of the portion of the structure exceeds 20 ft. 5. For developments with zero-lot-line single family dwellings, 0 ft along the zero lot line and 15 ft for the opposite interior side lot line.

Adopted September 2012, Amended Jan., Feb., and July 2013 City of Pompano Beach, Florida Page 3-10 Zoning Code Article 3: Zoning Districts Part 2 Residential Base Zoning Districts Section 155.3208 Multiple-Family Residence 7 (RM-7)

TYPICAL DEVELOPMENT CONFIGURATION

Min front yard Min interior setback: 25’ Max height: 35’ side yard setback: 8’

Min lot width : 60’

Min spacing between principal structures: 25’

Min front yard MULTIFAMILY DWELLING setback: 25’ Min lot area = 7,000 sq ft

Min street side yard setback: 8’ Max lot coverage = 60%

City of Pompano Beach, Florida Adopted Sept. 2012; Amended Jan. 2013, Feb. 2013, & July 2013 Zoning Code Page 3-11 Article 3: Zoning Districts Part 2 Residential Base Zoning Districts Section 155.3209 Multiple-Family Residence 12 (RM-12)

155.3209. MULTIPLE-FAMILY RESIDENCE 12 (RM-12)

A. PURPOSE TYPICAL BUILDING TYPE The Multiple-Family Residence 12 (RM-12) district is established and intended to accommodate primarily multifamily dwellings (including townhouse development) at moderate densities. The district also accommodates single-family and two-family dwellings, zero-lot-line development, community residential homes, assisted living facilities, and continuing care retirement communities. Limited neighborhood - serving nonresidential uses, as well as office buildings with a floor area of 2,000 square feet or less, are allowed as Special Exceptions.

B. USE STANDARDS See Appendix A: Consolidated Use Table, and use-specific standards in Article 4: Use Standards. C. INTENSITY AND DIMENSIONAL STANDARDS 1 Lot area, minimum (sq ft) 7,000 2 TYPICAL LOT PATTERN Lot width, minimum (ft) 60 2 Density, maximum (du/ac) 12 2,3 SF 950 2F 750 Floor area per dwelling unit, minimum (sq ft) Efficiency units: 500 MF Other units: 650 + 100 per BR>1 Lot coverage, maximum (% of lot area) 60 2 Pervious area, minimum (% of lot area) 25 2 Height, maximum (ft) 35 Front yard setback, minimum (ft) 25 Street side yard setback, minimum (ft) 8 2,4 Setback from a waterway or canal, minimum (ft) 25 Setback from a dune vegetation line, minimum (ft) 25 Interior side yard setback, minimum (ft) 8 2,4,5 Rear yard setback, minimum (ft) 10 4 Spacing between principal structures, minimum (ft) 25 Required Front Yard, Pervious Area, minimum (% of 50 (for Single Family Dwellings only) Required Front Yard) Dimensional Standards for Accessory Structures See Accessory Use-Specific standards in Article 4: Part 3. NOTES: [sq ft = square feet; ft = feet; du/ac = dwelling units/acre; SF = single-family dwelling; 2F = two-family dwelling; MF = multifamily dwelling; BR = bedroom] 1. See measurement rules and allowed exceptions/variations in Article 9:Part 4 . 2. For townhouse development, applies only to the development site as a whole, provided individual townhouse lots have a minimum area of 1,800 sq ft and a minimum width o f 18 ft. 3. On land classified Residential by the Land Use Plan, maximum gross residential density may not exceed that established for the particular land use classification. 4. Those portions of a structure extending above a height of 20 feet shall be set back an additional 1 ft for each 4 ft (or major fraction thereof) the height of the portion of the structure exceeds 20 ft. 5. For developments with zero-lot-line single family dwellings, 0 ft along the zero lot line and 15 ft for the opposite interior side lot line.

Adopted September 2012, Amended Jan., Feb., and July 2013 City of Pompano Beach, Florida Page 3-12 Zoning Code Article 3: Zoning Districts Part 2 Residential Base Zoning Districts Section 155.3209 Multiple-Family Residence 12 (RM-12)

TYPICAL DEVELOPMENT CONFIGURATION

Min front yard Max height: 35’ setback: 25’

Min lot width SF: 60’ Min interior side yard Min rear yard setback: 25’ setback: 8’

Min spacing between MULTIFAMILY DWELLING Min street principal Min lot area = 7,000 sq ft side yard structures: 25’ setback: 8’ Min front yard setback: Max lot coverage = 60% 25’

City of Pompano Beach, Florida Adopted Sept. 2012; Amended Jan. 2013, Feb. 2013, & July 2013 Zoning Code Page 3-13 Article 3: Zoning Districts Part 2 Residential Base Zoning Districts Section 155.3210 Multiple-Family Residence 20 (RM-20)

155.3210. MULTIPLE-FAMILY RESIDENCE 20 (RM-20)

A. PURPOSE TYPICAL BUILDING TYPE The Multiple-Family Residence 20 (RM-20) district is established and intended to accommodate primarily multifamily dwellings (including townhouse development) at moderate densities. The district also accommodates single-family and two-family dwellings, zero-lot-line development, community residen tial homes, assisted living facilities, and continuing care retirement communities. Limited neighborhood - serving nonresidential uses, as well as office buildings, financial institutions, hotels/motels, and apartment hotels, are allowed as Special Exceptio ns.

B. USE STANDARDS See Appendix A: Consolidated Use Table, and use-specific standards in Article 4: Use Standards. C. INTENSITY AND DIMENSIONAL STANDARDS 1 2 Lot area, minimum (sq ft) SF: 7,000 2F: 8,000 MF: 8,800 TYPICAL LOT PATTERN Lot width, minimum (ft) SF: 60 2F: 70 MF: 75 2 Density, maximum (du/ac) 20 2,3 SF 950 2F 750 Floor area per dwelling unit, minimum (sq ft) Efficiency units: 500 MF Other units: 650 + 100 per BR>1 Lot coverage, maximum (% of lot area) 60 2 Pervious area, minimum (% of lot area) 25 2 Height, maximum (ft) 35 Front yard setback, minimum (ft) 25 Street side yard setback, minimum (ft) 10 2,4

Setback from a waterway or canal, minimum (ft) 25 Setback from a dune vegetation line, minimum (ft) 25 Interior side yard setback, minimum (ft) 10 2,4,5 Rear yard setback, minimum (ft) 10 4 Spacing between principal structures, minimum (ft) 25 Required Front Yard, Pervious Area, minimum (% of 50 (for Single Family Dwellings only) Required Front Yard) Dimensional Standards for Accessory Structures See Accessory Use-Specific standards in Article 4: Part 3. NOTES: [sq ft = square feet; ft = feet; du/ac = dwelling units/acre; SF = single-family dwelling; 2F = two-family dwelling; MF = multifamily dwelling; BR = bedroom] 1. See measurement rules and allowed exceptions/variations in Article 9:Part 4 . 2. For townhouse development, applies only to the development site as a whole, provided individual townhouse lots have a minimum area of 1,800 sq ft and a minimum width of 18 ft. 3. On land classified Residential by the Land Use Plan, maximum gross residential density may not exceed that established for the particular land use classification. 4. Those portions of a structur e extending above a height of 20 feet shall be set back an additional 1 ft for each 4 ft (or major fraction thereof) the height of the portion of the structure exceeds 20 ft. 5. For developments with zero-lot-line single family dwellings, 0 ft along the zero lot line and 15 ft for the opposite interior side lot line.

Adopted September 2012, Amended Jan., Feb., and July 2013 City of Pompano Beach, Florida Page 3-14 Zoning Code Article 3: Zoning Districts Part 2 Residential Base Zoning Districts Section 155.3210 Multiple-Family Residence 20 (RM-20)

TYPICAL DEVELOPMENT CONFIGURATION

MULTIFAMILY DWELLING Min lot area = 8,800 sq ft Max lot coverage = 60% Min lot width MF: 75 ’

Min interior side yard setback: 10 ’ Min spacing between principal structures: 25’ Max height: 35’

Min rear yard setback: 10’

Min street side yard setback: Min front yard setback: 25’ 10 ’

City of Pompano Beach, Florida Adopted Sept. 2012; Amended Jan. 2013, Feb. 2013, & July 2013 Zoning Code Page 3-15 Article 3: Zoning Districts Part 2 Residential Base Zoning Districts Section 155.3211 Multiple-Family Residence 30 (RM-30)

155.3211. MULTIPLE-FAMILY RESIDENCE 30 (RM-30)

A. PURPOSE TYPICAL BUILDING TYPE The Multiple-Family Residence 30 (RM-30) district is established and intended to accommodate primarily multifamily dwellings (including townhouse development) at moderately high densities. The district also accommodates single-family and two-family dwellings, zero-lot-line de velopment, community residential homes, assisted living facilities, and continuing care retirement communities. Limited neighborhood- serving nonresidential uses, as well as office buildings, financial institutions, hotels/motels, and apartment hotels, are allowed as Special Exceptions

B. USE STANDARDS See Appendix A: Consolidated Use Table, and use-specific standards in Article 4: Use Standards. C. INTENSITY AND DIMENSIONAL STANDARDS 1 Lot area, minimum (sq ft) SF: 7,000 2F: 8,000 MF: 8,800 2 TYPICAL LOT PATTERN Lot width, minimum (ft) SF: 60 2F: 70 MF: 75 2 Density, maximum (du/ac) 30 2,3 SF 950 2F 750 Floor area per dwelling unit, minimum (sq ft) Efficiency units: 500 MF Other units: 650 + 100 per BR>1 Lot coverage, maximum (% of lot area) 60 2 Pervious area, minimum (% of lot area) 25 2 Height, maximum (ft) 105 4 Front yard setback, minimum (ft) 25 Street side yard setback, minimum (ft) 10 2,5 Setback from a waterway or canal, minimum (ft) 25 Setback from a dune vegetation line, minimum (ft) 25 Interior side yard setback, minimum (ft) 10 2,5,6 Rear yard setback, minimum (ft) 10 5 Spacing between principal structures, minimum (ft) 25 Required Front Yard, Pervious Area, minimum (% of 50 (for Single Family Dwellings only) Required Front Yard) Dimensional Standards for Accessory Structures See Accessory Use-Specific standards in Article 4: Part 3. NOTES: [sq ft = square feet; ft = feet; du/ac = dwelling units/acre; SF = single-family dwelling; 2F = two-family dwelling; MF = multifamily dwelling; BR = bedroom] 1. See measurement rules and allowed exceptions/variations in Article 9:Part 4 . 2. For townhouse development, applies only to the development site as a whole; individual townhouse lots must have a minimum area of 1,800 sq ft and a minimum width of 18 ft. 3. On land classified Residential by the Land Use Plan, maximum gross residential density may not exceed that established for the particular land use classification. 4. Structures with in the Air Park Overlay (APO) zoning district must also comply with the height limits in Section 155.3707. 5. Those portions of a structure extending above a height of 20 feet shall be set back an additional 1 ft for each 4 ft (or major fraction thereof) the height of the portion of the structure exceeds 20 ft. 6. For developments with zero-lot-line single family dwellings, 0 ft along the zero lot line and 15 ft for the opposite interior side lot line.

Adopted September 2012, Amended Jan., Feb., and July 2013 City of Pompano Beach, Florida Page 3-16 Zoning Code Article 3: Zoning Districts Part 2 Residential Base Zoning Districts Section 155.3211 Multiple-Family Residence 30 (RM-30)

TYPICAL DEVELOPMENT CONFIGURATION

MULTIFAMILY DWELLING Min lot area = 8,800 sq ft Max lot coverage = 60%

Max height: 10 5’

Min interior side yard setback: 10 ’

Min spac ing between principal Min rear yard structures: 25’ setback: 10’

Min lot width MF: 75 ’

Min front yard setback: 25’ Min street side yard setback: 10 ’

City of Pompano Beach, Florida Adopted Sept. 2012; Amended Jan. 2013, Feb. 2013, & July 2013 Zoning Code Page 3-17 Article 3: Zoning Districts Part 2 Residential Base Zoning Districts Section 155.3212 Multiple-Family Residence 45 (RM-45)

155.3212. MULTIPLE-FAMILY RESIDENCE 45 (RM-45)

A. PURPOSE TYPICAL BUILDING TYPE The Multiple-Family Residence 45 (RM-45) district is established and intended to accommodate primarily multifamily dwellings (including townhouse development) at high densities. The district also accommodates single-family and two-family dwellings, zero-lot-line development, community residential homes, assisted living facilities, and continuing care retirement communities. Limited neighborhood -serving nonresidential uses, as well as office buildings, financial institutions, hotels/motels, and apartment hotels, are allowed as Special Exceptions.

B. USE STANDARDS See Appendix A: Consolidated Use Table, and use-specific standards in Article 4: Use Standards. C. INTENSITY AND DIMENSIONAL STANDARDS 1 Lot area, minimum (sq ft) SF: 7,000 2F: 8,000 MF: 8,800 2 TYPICAL LOT PATTERN Lot width, minimum (ft) SF: 60 2F: 70 MF: 75 2 Density, maximum (du/ac) 45 2,3 SF 950 2F 750 Floor area per dwelling unit, minimum (sq ft) Efficiency units: 500 MF Other units: 650 + 100 per BR>1 Lot coverage, maximum (% of lot area) 60 2 Pervious area, minimum (% of lot area) 25 2 Height, maximum (ft) 105 4,5 Front yard setback, minimum (ft) 25 Street side yard setback, minimum (ft) 10 2,6 Setback from a waterway or canal, minimum (ft) 25 Setback from a dune vegetation line, minimum (ft) 25 Interior side yard setback, minimum (ft) 10 2,6,7 Rear yard setback, minimum (ft) 10 6 Spacing between principal structures, minimum (ft) 25 Required Front Yard, Pervious Area, minimum (% of 50 (for Single Family Dwellings only) Required Front Yard) Dimensional Standards for Accessory Structures See Accessory Use-Specific standards in Article 4: Part 3. NOTES: [sq ft = square feet; ft = feet; du/ac = dwelling units/acre; SF = single-family dwelling; 2F = two-family dwelling; MF = multifamily dwelling; BR = bedroom] 1. See measurement rules and allowed exceptions/variations in Article 9:Part 4 . 2. For townhouse development, applies only to the development site as a whole, provided individual townhouse lots have a minimum area of 1,800 sq ft and a minimum width of 18 ft. 3. On land classified Residential by the Land Use Plan, maximum gross residential density may not exceed that established for the particular land use classification. 4. Structures within the Air Pa rk Overlay (APO) zoning district must also comply with the height limits in Section 155.3707. 5. Not applicable within a Multiple -Family Residence45 High-Rise (RM-45 HR) Overlay district. 6. Those portions of a structure extending above a height of 20 feet shall be set back an additional 1 ft for each 4 ft (or major fraction thereof) the height of the portion of the structure exceeds 20 ft. 7. For developments with zero-lot-line single family dwellings, 0 ft along the zero lot line and 15 ft for the opposite interior side lot line.

Adopted September 2012, Amended Jan., Feb., and July 2013 City of Pompano Beach, Florida Page 3-18 Zoning Code Article 3: Zoning Districts Part 2 Residential Base Zoning Districts Section 155.3212 Multiple-Family Residence 45 (RM-45)

TYPICAL DEVELOPMENT CONFIGURATION

MULTIFAMILY DWELLING Min lot area = 8,800 sq ft Max lot coverage = 60%

Max height: 10 5’

Min interior side yard setback: 10 ’

Min setback from dune vegetation Min lot width MF: 75 ’ line: 25’

Min street side yard setback: 10 ’ Min front yard setback: 25’

City of Pompano Beach, Florida Adopted Sept. 2012; Amended Jan. 2013, Feb. 2013, & July 2013 Zoning Code Page 3-19 Article 3: Zoning Districts Part 2 Residential Base Zoning Districts Section 155.3213 Mobile Home Park (MH-12)

155.3213. MOBILE HOME PARK (MH-12)

A. PURPOSE TYPICAL BUILDING TYPE The Mobile Home Park (MH-12) district is established and intended to accommodate mobile home parks that primarily function to provide spaces for individual mobile homes intended to be occupied as permanent living quarters. The district also accommodates re creational facilities and other accessory uses serving occupants of the mobile home park .

B. USE STANDARDS See Appendix A: Consolidated Use Table, and use-specific standards in Article 4: Use Standards. C. INTENSITY AND DIMENSIONAL STANDARDS 1

Lot area, minimum (acres) 5 TYPICAL LOT PATTERN Lot width, minimum (ft) 300 Density, maximum (du/ac) 12 2 Height, maximum (ft) 12 Setback from a waterway or canal, minimum (ft) 25 Front yard setback per mobile home space, minimum (ft) 25 3 Street side yard setback per mobile home space, minimum (ft) 10 3 Interior side yard setback per mobile home space, minimum (ft) 10 3 Rear yard setback per mobile home space, minimum (ft) 15 3 Spacing between mobile homes, minimum (ft) 10 3 Dimensional Standards for Accessory Structures See Accessory Use-Specific standards in Article 4: Part 3. NOTES: [sq ft = square feet; ft = feet; du/ac = dwelling units/acre] 1. See measurement rules and allowed exceptions/variations in Article 9:Part 4 . 2. On land classified Residential by the Land Use Plan, maximum gross residential density may not exceed that established for the particular land use classification. 3. If the mobile home pa rk was zoned R-1T under former county zoning and consists of mobile home spaces that are individually owned or leased for terms of one year or more, the minimum front and street side yard setbacks are 6 ft, the interior side yard setback is 4 ft, the rear yard setback is 8 ft, and the interior side yard setback for roofed carports is 2 ft. 4. 25 ft between a mobile home and any accessory or service structure used in conjunction with the park. TYPICAL DEVELOPMENT CONFIGURATION

Min street side yard setback: 10’

Max height: 35’

Min front yard setback: 25’ Min interior side yard setback: 10’ Min rear yard setback: 1 5’ Min lot width MF: 300 ’

Adopted September 2012, Amended Jan., Feb., and July 2013 City of Pompano Beach, Florida Page 3-20 Zoning Code