O1 Oil Hardening Tool Steel

Total Page：16

File Type：pdf, Size：1020Kb

O1 OIL HARDENING TOOL STEEL ANNEALING Heat slowly and uniformly to 1140°F; soak thoroughly and then allow to cool slowly in the furnace to below 1000ºF. STRESS RELIEVING When heavy machining cuts are employed the resultant stresses may be relieved by heating the material to 1200 -1250°F for one hour and cooling in still air. Finish machine after stress relieving. HARDENING Preheat thoroughly to 1200-1250°F and then raise temperature to 1450°F - 1500°F depending on section size. Hold until uniformly heated through. Use high side of hardening range for thicker sections. QUENCHING Quench in warm thin quenching oil to about 125ºF. To prevent soft spots the tools should be rapidly agitated in the oil when a circulating oil bath is not available. The material should be tempered as soon as it has cooled to 125ºF. TEMPERING Temper immediately to desired hardness. For most applications a tempering temperature of 400-450ºF is employed. However, for cutting tools requiring high hardness, low temperatures of 300-375ºF are suitable. Temper a minimum of two hours for sections under two inches and a minimum of one hour per inch of thickness over two inches. APPLICATIONS Gauges, shims, stamps, jigs, cutters, templates, cams, guides, levers, saws, knives, straight edges, fixtures, machine parts, punches, blanking dies, draw dies, forming dies, lamination dies, molding dies, swaging dies, screw dies and trim dies. TEMPERING ROCKWELL The tempering NOMINAL ANALYSIS TEMPERATURE HARDNESS table shows the hardness values C Mn W Cr V As hardened C 63-65 obtained at 300°F C 63-64 various tempering 0.90 1.0 0.50 0.50 0.15 temperatures on 400°F C 61-62 a two inch cube 500°F C 58-60 of steel hardened NOTE: This information is intended to server only as a 600°F C 54-56 from 1475°F and guide. Variations in analysis, size, heat treatment, tempered two etc., may result in slight deviations from this data. 800°F C 48-50 hours. 1000°F C 39-41 VISIT ANY OF OUR BRANCH LOCATIONS LOS ANGELES ORANGE COUNTY SAN DIEGO INLAND EMPIRE PHOENIX (818) 729-3333 (949) 250-3343 (858) 277-8200 (951) 300-9900 (602) 454-1500 .

Copy Link

Recommended publications

UDDEHOLM STAVAX® ESR © UDDEHOLMS AB No Part of This Publication May Be Reproduced Or Transmitted for Commercial Purposes Without Permission of the Copyright Holder
UDDEHOLM STAVAX® ESR © UDDEHOLMS AB No part of this publication may be reproduced or transmitted for commercial purposes without permission of the copyright holder. This information is based on our present state of knowledge and is intended to provide general notes on our products and their uses. It should not therefore be construed as a warranty of specific properties of the products described or a warranty for fitness for a particular purpose. Classified according to EU Directive 1999/45/EC For further information see our “Material Safety Data Sheets”. Edition 11, 05.2013 The latest revised edition of this brochure is the English version, SS-EN ISO 9001 which is always published on our web site www.uddeholm.com SS-EN ISO 14001 UDDEHOLM STAVAX ESR UDDEHOLM STAVAX ESR Uddeholm Stavax ESR is a premium stainless mould steel for small and medium inserts and cores. Uddeholm Stavax ESR combines corrosion and wear resistance with excellent polishability, good machinability and stability in hardening. Mould maintenance requirement is reduced by assuring that core and cavity surfaces retain their original finish over extended operating periods. When compared with non stainless mould steel, Uddeholm Stavax ESR offers lower production costs by maintaining rust free cooling channels, assuring consistent cooling and cycle time. This classic stainless tool steel is the right choice when rust in production is unacceptable and where requirements for good hygiene are high, as within the medical industry, optical industry and for other high quality transparent parts. Uddeholm Stavax ESR is a part of the Uddeholm Stainless Concept 3 UDDEHOLM STAVAX ESR General Applications Uddeholm Stavax ESR is a premium grade Uddeholm Stavax ESR is recommended for all stainless tool steel with the following proper- types of moulding tools and its special proper- ties: ties make it particularly suitable for moulds •good corrosion resistance with the following demands: •excellent polishability • Corrosion/staining resistance, i.e.
[Show full text]
Chromium Martensitic Hot-Work Tool Steels Hot-Work Tool Steels Division for Engineering Sciences, Physics and Mathematics Department of Materials Engineering
Chromium martensitic Sjöström Johnny hot-work tool steels Division for Engineering Sciences, Physics and Mathematics Department of Materials Engineering Chromium martensitic hot-work tool steels martensitic hot-work Chromium Chromium martensitic hot-work tool steel (AISI H13) was developed to endure the severe conditions of high temperature metal forming operations such as die cast- ing, hot rolling, extrusion and hot forging. The mechanical properties are high and strongly connected to the microstructure and have been improved over the years by Johnny Sjöström alloying and heat treatment. Damages still occur and one of the most common failure mechanisms is thermal fatigue. In this thesis the thermal fatigue damage on hot forming tools has been studied. Several types of hot work tools steels have been experimentally tested and the mi- crostructural changes during thermal fatigue have been evaluated. The tool material behaviour has also been simulated to support the integration of die design, tool steel properties and use. Chromium martensitic The general aim of this thesis is to increase the knowledge of the chromium martensitic hot-work tool steel damage, performance and microstructure. hot-work tool steels – damage, performance and microstructure Karlstad University Studies Karlstad University Studies ISSN 1403-8099 2004:52 ISBN 91-85335-21-5 Johnny Sjöström Chromium martensitic hot-work tool steels – damage, performance and microstructure Karlstad University Studies 2004:52 Johnny Sjöström. Chromium martensitic hot-work tool steels
[Show full text]
Structure/Property Relationships in Irons and Steels Bruce L
Copyright © 1998 ASM International® Metals Handbook Desk Edition, Second Edition All rights reserved. J.R. Davis, Editor, p 153-173 www.asminternational.org Structure/Property Relationships in Irons and Steels Bruce L. Bramfitt, Homer Research Laboratories, Bethlehem Steel Corporation Basis of Material Selection ............................................... 153 Role of Microstructure .................................................. 155 Ferrite ............................................................. 156 Pearlite ............................................................ 158 Ferrite-Pearl ite ....................................................... 160 Bainite ............................................................ 162 Martensite .................................... ...................... 164 Austenite ........................................................... 169 Ferrite-Cementite ..................................................... 170 Ferrite-Martensite .................................................... 171 Ferrite-Austenite ..................................................... 171 Graphite ........................................................... 172 Cementite .......................................................... 172 This Section was adapted from Materials 5election and Design, Volume 20, ASM Handbook, 1997, pages 357-382. Additional information can also be found in the Sections on cast irons and steels which immediately follow in this Handbook and by consulting the index. THE PROPERTIES of irons and steels
[Show full text]
14-4Crmo Stainless Tool Steel
DATA SHEET Issue 1 14-4CrMo Stainless Tool Steel Typical Composition C Mn Si Cr Mo 1.05 0.50 0.30 14.00 4.00 14-4CrMo is a wear resistant, martensitic stainless tool steel that exhibits better corrosion resistance than Type 440C stainless steel. The molybdenum in the steel provides superior corrosion resistance compared to some higher-chromium stainless steels. The combination of the high carbon and molybdenum contents results in the formation of hard, wear-resistant molybdenum carbides in the microstructure of the steel. These molybdenum carbides provide superior wear resistance and edge retention for cutting tools and knives. Typical applications include knife blades, bearings, valve components, and bushings. Relative Properties Wear Resistance Corrosion Resistance Toughness 14-4CrMo 440C D2 61 HRC 58 HRC 61 HRC Physical Properties 3 3 Density: 0.281 lb/in (7780 kg/m ) Specific Gravity: 7.78 6 Modulus of Elasticity: 30x10 psi (207GPa) Coefficient of Thermal Expansion: Thermal Conductivity Temperature in/in/ Temperature mm/mm/ Temp. Btu/ Temp. W/ °F °F x 10-6 °C °C x 10-6 °F hr-ft-°F °C m-°C 68 - 212 5.7 20 - 100 10.3 200 14.0 392 24.2 68 - 600 6.0 20 - 316 10.8 Machinability: 60-65% of a 1% carbon steel COPYRIGHT© 2006 by Latrobe Specialty Steel Co. TM-Trademark of Latrobe Specialty Steel Co. 12/06 14-4CrMo HEAT TREATMENT RESPONSE HEAT TREATING INSTRUCTIONS (See Tech-Topics Bulletin 102 for a more thorough As Oil Quenched from HRC explanation of heat treating.) 1850°F (1010°C), 45 minutes 60 1900°F (1038°C), 45 minutes 63.3 1950°F (1066°C), 45 minutes 63 HARDENING: 1975°F (1080°C), 45 minutes 62.5 Preheating: Heat to 1100-1250°F (593-677°C), and 2000°F (1093°C), 45 minutes 61 equalize.
[Show full text]
LSS™ D3 Tool Steel (ASTM D3)
DATA SHEET Issue 1 LSS™ D3 Tool Steel (ASTM D3) Typical Composition C Mn Si Cr V 2.15 0.40 0.40 12.25 0.25 LSS D3 tool steel is a high-carbon, high-chromium, oil-hardening tool steel that is characterized by a relatively high attainable hardness and numerous, large, chromium-rich alloy carbides in the microstructure. These carbides provide good resistance to wear from sliding contact with other metals and abrasive materials. LSS D3 exhibits excellent stability in heat treatment, holding size almost as well as the air-hardening, high-carbon, high-chromium die steels such as D2. Typical applications for LSS D3 tool steel include forming rolls, drawing dies, forming, powder compaction tooling, and lamination dies. Relative Properties Wear Resistance Toughness Grindability LSS D3 D2 D5 D7 62 HRC 62 HRC 62 HRC 63 HRC Physical Properties Coefficient of Thermal Expansion: (at 61-62HRC) 3 3 Density: 0.284 lb/in (7870 kg/m ) Temperature, in/in Temperature, mm/mm Specific Gravity: 7.87 °F °Fx10-6 °C °Cx10-6 Modulus of Elasticity: 30x106 psi (207 GPa) 100 - 500 6.58 38 - 260 11.84 100 - 800 7.15 38 - 427 12.87 Machinability: 45-50% of a 1% carbon steel 100 - 1000 7.32 38 - 538 13.81 100 - 1200 7.54 38 - 649 13.57 100 - 1500 7.72 38 - 816 13.90 COPYRIGHT© 2006 by Latrobe Specialty Steel Co. TM-Trademark of Latrobe Specialty Steel Co. 12/06 ™ LSS D3 HEAT TREATING INSTRUCTIONS HEAT TREATMENT RESPONSE (See Tech-Topics Bulletin 102 for a more thorough As Air Cooled from HRC explanation of heat treating.) 1675°F (913°C), 45 minutes 63.5 HARDENING: 1700°F (927°C), 30 minutes 64.5 Critical Temperatures: 1750°F (954°C), 30 minutes 64.5 Ac1: 1440°F (782°C) Ac3: 1530°F (832°C) 1800°F (982°C), 30 minutes 64 Ar1: 1410°F (766°C) Ar3: 1370°F (743°C) Tempering Temperature, °C Preheating: To minimize distortion and stresses in 94 205 316 427 538 649 large or complex tools use a double preheat.
[Show full text]
Microstructure and Mechanical Properties of a 5 Wt.% Cr Cold Work Tool Steel - Influence of Heat Treatment Procedure
MUHAMMAD ARBAB REHAN MUHAMMAD ARBAB Licentiate Thesis Production Technology 2017 No. 18 Microstructure and mechanical MICROSTRUCTURE AND MECHANICAL PROPERTIES OF A 5 WT.% CR COLD WORK TOOL STEEL - INFLUENCE OF HEAT TREATMENT PROCEDURE. TREATMENT OF HEAT - INFLUENCE STEEL TOOL CR COLD WORK OF A 5 WT.% PROPERTIES AND MECHANICAL MICROSTRUCTURE properties of a 5 wt.% Cr cold work tool steel - Inﬂuence of heat treatment procedure. Muhammad Arbab Rehan 2017 NO.18 2017 ISBN 978-91-87531-56-9 (Printed) ISBN 978-91-87531-55-2 (Electronic) Tryck: Ineko AB, april 2017. Licentiate Thesis Production Technology 2017 No. 18 Microstructure and mechanical properties of a 5 wt.% Cr cold work tool steel - Influence of heat treatment procedure. Muhammad Arbab Rehan University West SE-46186 Trollhättan Sweden +46-520 22 30 00 www.hv.se © Muhammad Arbab Rehan 2017 Print Book ISBN 978-91-87531-56-9 eBook ISBN 978-91-87531-55-2 Acknowledgements I must admit that there are a lot of people who have helped me with the passage of time. However, I would like to acknowledge and express my gratitude to the most important ones, my parents. They have always been understanding, helpful and stood by me in all parts of life. Their positive approach and wise suggestions have always lifted me up. I would also like to thank my wife (Mehroze Nasim Khan) who has been supportive in all aspects of life. It has been a wonderful experience growing with her together with my beautiful daughter. Moreover, my sister and brothers who had given me a joyous childhood and have always contributed to my personality.
[Show full text]
Enghandbook.Pdf
785.392.3017 FAX 785.392.2845 Box 232, Exit 49 G.L. Huyett Expy Minneapolis, KS 67467 ENGINEERING HANDBOOK TECHNICAL INFORMATION STEELMAKING Basic descriptions of making carbon, alloy, stainless, and tool steel p. 4. METALS & ALLOYS Carbon grades, types, and numbering systems; glossary p. 13. Identification factors and composition standards p. 27. CHEMICAL CONTENT This document and the information contained herein is not Quenching, hardening, and other thermal modifications p. 30. HEAT TREATMENT a design standard, design guide or otherwise, but is here TESTING THE HARDNESS OF METALS Types and comparisons; glossary p. 34. solely for the convenience of our customers. For more Comparisons of ductility, stresses; glossary p.41. design assistance MECHANICAL PROPERTIES OF METAL contact our plant or consult the Machinery G.L. Huyett’s distinct capabilities; glossary p. 53. Handbook, published MANUFACTURING PROCESSES by Industrial Press Inc., New York. COATING, PLATING & THE COLORING OF METALS Finishes p. 81. CONVERSION CHARTS Imperial and metric p. 84. 1 TABLE OF CONTENTS Introduction 3 Steelmaking 4 Metals and Alloys 13 Designations for Chemical Content 27 Designations for Heat Treatment 30 Testing the Hardness of Metals 34 Mechanical Properties of Metal 41 Manufacturing Processes 53 Manufacturing Glossary 57 Conversion Coating, Plating, and the Coloring of Metals 81 Conversion Charts 84 Links and Related Sites 89 Index 90 Box 232 • Exit 49 G.L. Huyett Expressway • Minneapolis, Kansas 67467 785-392-3017 • Fax 785-392-2845 • [email protected] • www.huyett.com INTRODUCTION & ACKNOWLEDGMENTS This document was created based on research and experience of Huyett staff. Invaluable technical information, including statistical data contained in the tables, is from the 26th Edition Machinery Handbook, copyrighted and published in 2000 by Industrial Press, Inc.
[Show full text]
Introduction to Basic Manufacturing Processes and Workshop Technology 8 CHAPTER
130 Introduction to Basic Manufacturing Processes and Workshop Technology 8 CHAPTER HEAT TREATMENT 8.1 INTRODUCTION Heat treatment is a heating and cooling process of a metal or an alloy in the solid state with the purpose of changing their properties. It can also be said as a process of heating and cooling of ferrous metals especially various kinds of steels in which some special properties like softness, hardness, tensile-strength, toughness etc, are induced in these metals for achieving the special function objective. It consists of three main phases namely (i) heating of the metal (ii) soaking of the metal and (iii) cooling of the metal. The theory of heat treatment is based on the fact that a change takes place in the internal structure of metal by heating and cooling which induces desired properties in it. The rate of cooling is the major controlling factor. Rapid cooling the metal from above the critical range, results in hard structure. Whereas very slow cooling produces the opposite affect i.e. soft structure. In any heat treatment operation, the rate of heating and cooling is important. A hard material is difficult to shape by cutting, forming, etc. During machining in machine shop, one requires machineable properties in job piece hence the properties of the job piece may requires heat treatment such as annealing for inducing softness and machineability property in workpiece. Many types of furnaces are used for heating heat treatment purposes. The classification of such heat treatment furnaces is given as under. 8.2 HEAT TREATMENT FURNACES 8.2.1 Hearth Furnaces These furnaces are heated by fuel which may be coke, coal, gas (town, blast or natural) and fuel oil.
[Show full text]
Retained Austenite Control for the Soft Machining of High-Hardness Tool Steels
metals Article Retained Austenite Control for the Soft Machining of High-Hardness Tool Steels Maider Muro 1 ID , Garikoitz Artola 1, Josu Leunda 2, Carlos Soriano 2 and Carlos Angulo 3,* ID 1 Metallurgy Research Centre IK4 AZTERLAN, Metallurgical Processes, Forming Technology Unit, Aliendalde Auzunea 6, 48200 Durango, Spain; [email protected] (M.M.); [email protected] (G.A.) 2 IK4-Tekniker, Advanced Manufacturing Technologies Unit, Polo Tecnológico de Eibar, Iñaki Goenaga 5, 20600 Eibar, Spain; [email protected] (J.L.); [email protected] (C.S.) 3 Department of Mechanical Engineering, University of the Basque Country (UPV/EHU), Plaza Ingeniero Torres Quevedo 1, 48013 Bilbao, Spain * Correspondence: [email protected]; Tel.: +34-94-601-4217 Received: 22 June 2018; Accepted: 20 July 2018; Published: 23 July 2018 Abstract: Most high-hardness tool steels comprising forming dies require expensive finish machining operations to compensate for the dimensional distortion and surface oxidation caused by the die heat treatment. Precipitation-hardening (PH) tool steels allow for soft finish machining followed by an aging treatment without major deformation or oxidation in the die, but exhibit poor wear performance owing to the lack of carbides in their structure. This drawback can be overcome by combining laser cladding technology, austenite retention, and cryogenic treatments. Hence, an alternative die manufacturing route based on laser cladding was explored. The forming surface of a modified chemistry tool steel die was subjected to cladding. The martensite finish (Mf) temperature of the steel was tuned to enhance austenite retention at room temperature. The cladded surface was then machined in a reduced-hardness condition resulting from retained austenite formation.
[Show full text]
Heat Treatment and Properties of Iron and Steel
National Bureau of Standards Library, N.W. Bldg NBS MONOGRAPH 18 Heat Treatment and Properties of Iron and Steel U.S. DEPARTMENT OF COMMERCE NATIONAL BUREAU OF STANDARDS THE NATIONAL BUREAU OF STANDARDS Functions and Activities The functions of the National Bureau of Standards are set forth in the Act of Congress, March 3, 1901, as amended by Congress in Public Law 619, 1950. These include the development and maintenance of the national standards of measurement and the provision of means and methods for making measurements consistent with these standards; the determination of physical constants and properties of materials; the development of methods and instruments for testing materials, devices, and structures; advisory services to government agencies on scientific and technical problems; inven- tion and development of devices to serve special needs of the Government; and the development of standard practices, codes, and specifications. The work includes basic and applied research, develop- ment, engineering, instrumentation, testing, evaluation, calibration services, and various consultation and information services. Research projects are also performed for other government agencies when the work relates to and supplements the basic program of the Bureau or when the Bureau's unique competence is required. The scope of activities is suggested by the listing of divisions and sections on the inside of the back cover. Publications The results of the Bureau's work take the form of either actual equipment and devices or pub- lished papers.
[Show full text]
A Simplified Guide to Heat Treating Tool Steels
A Simplified Guide to Heat Treating Tool Steels When we consider that the greater overall costs of most tools and dies are incurred prior to heat treatment and further that proper heat treatment is critical to the successful application of tooling, this so-called “hardening” process is placed in it’s proper perspective of importance. While there are a number of specialized procedures which can be employed in the heat treatment of tool steels, the purpose of this discussion is to review the basic heat treating process, it’s steps and terms, and perhaps offer some helpful hints along the way. The Heat Treating Process The process consists of: A) PREHEATING the Annealed tool, typically at 1250 degrees F. B) AUSTENITIZING (Soaking at High Heat). C) QUENCHING – Quench to Hard Brittle (Martensite) condition. D) TEMPERING (Drawing to desired hardness). Annealing Tool steels are furnished in the annealed condition which is the soft, machineable and necessary condition for proper heat treat response. The exceptions to this are the prehardened steels such as P-20, Brake Die, Holder Block and Maxel Tooling Plate which are furnished at 28/32 HRC and used at that hardness. Tool steels should always be annealed prior to re-hardening and annealed steels should be re-annealed after welding. Unlike hardening which requires a quench after soaking at the hardening temperature, the essence of annealing is very slow cooling from the annealing temperature. By way of example, A2 tool steel is annealed by heating to 1550 degrees F, soaking for two hours at temperature, furnace cooling 50 degrees F per hour to below 1200 degrees F followed by air cooling.
[Show full text]
Die Material Selection Criteria for Aluminum Hot Stamping
Journal of Manufacturing and Materials Processing Article Die Material Selection Criteria for Aluminum Hot Stamping Maider Muro 1 , Ines Aseguinolaza 2 and Garikoitz Artola 1,* 1 AZTERLAN, Basque Research and Technology Alliance (BRTA), Aliendalde Auzunea 6, 48200 Durango, Spain; [email protected] 2 BATZ, Torrea Auzoa 2, 48140 Igorre, Spain; [email protected] * Correspondence: [email protected]; Tel.: +34-946-215-470 Abstract: The aim of this work is to develop a die material selection criterion for aluminum hot stamping applications. The criterion has been based on the back-to-back comparison of a set of reciprocating friction and wear tests. Three representatives belonging to different stamping die material families have been selected for the study: a cold work steel, a hot work steel, and a cast iron. These tool materials have been combined with an exemplary member from two heat treatable aluminum families: 2XXX and 6XXX. Each die-material/aluminum–alloy combination has been tested at three temperatures: 40, 200, and 450 ◦C. The temperatures have been selected according to different stamping scenarios: long takt time press quenching, short takt time press quenching, and very short takt time hot forming without quenching, respectively. The results show that, among the three die material options available, the cold work steel turned out to be the most favorable option for high volume production and long takt time, the hot work steel ﬁtted best for high volume production coupled with short takt time, and cast iron turned to outstand for short runs with prototype dies and for hot stamping without die quenching. Keywords: selection criterion; die material; aluminum alloy; hot stamping; tool steel; cast iron; friction; wear Citation: Muro, M.; Aseguinolaza, I.; Artola, G.
[Show full text]