DOCSLIB.ORG

Controlling Satellite Communication System Unwanted Emissions in Congested RF Spectrum

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Controlling Satellite Communication System Unwanted Emissions in Congested RF Spectrum Controlling Satellite Communication System Unwanted Emissions in Congested RF Spectrum Donald Olsen The Aerospace Corporation P.O. Box 92957 Los Angeles, CA 90009-2957 Roger Heymann National Environmental Satellite Service NOAA-NESDIS Building SSMC1, 5th Floor 1335 East-West Highway Silver Spring, MD 20910 ABSTRACT The International Telecommunication Union (ITU), a United Nations (UN) agency, is the agency that, under an international treaty, sets radio spectrum usage regulations among member nations. Within the United States of America (USA), the organization that sets regulations, coordinates an application for use, and provides authorization for federal government/agency use of the radio frequency (RF) spectrum is the National Telecommunications and Information Administration (NTIA). In this regard, the NTIA defines which RF spectrum is available for federal government use in the USA, and how it is to be used. The NTIA is a component of the United States (U.S.) Department of Commerce of the federal government. The significance of ITU regulations is that ITU approval is required for U.S. federal government/agency permission to use the RF spectrum outside of U.S. boundaries. All member nations have signed a treaty to do so. U.S. federal regulations for federal use of the RF spectrum are found in the Manual of Regulations and Procedures for Federal Radio Frequency Management, and extracts of the manual are found in what is known as the Table of Frequency Allocations. Nonfederal government and private sector use of the RF spectrum within the U.S. is regulated by the Federal Communications Commission (FCC). There is a need to control “unwanted emissions” (defined to include out-of-band emissions, which are those immediately adjacent to the necessary and allocated bandwidth, plus spurious emissions) to preclude interference to all other authorized users. This paper discusses the causes, effects, and mitigation of unwanted RF emissions to systems in adjacent spectra. Digital modulations are widely used in today’s satellite communications. Commercial communications sector standards are covered for the most part worldwide by Digital Video Broadcast - Satellite (DVB-S) and digital satellite news gathering (DSNG) evolutions and the second generation of DVB-S (DVB-S2) standard, developed by the European Telecommunications Standards Institute (ETSI). In the USA, the Advanced Television Systems Committee (ATSC) has adopted Europe’s DVB-S and DVB-S2 standards for satellite digital transmission. With today’s digital modulations, RF spectral side lobes can extend out many times the modulating frequency on either side of the carrier at excessive power levels unless filtered. Higher-order digital modulations include quadrature phase shift keying (QPSK), 8 PSK (8-ary phase shift keying), 16 APSK (also called 12-4 APSK (amplitude phase shift keying)), and 16 QAM (quadrature amplitude modulation); they are key for higher spectrum efficiency to enable higher data rate transmissions in limited available bandwidths. Nonlinear high-power amplifiers (HPAs) can regenerate frequency spectral side lobes on input-filtered digital modulations. The paper discusses technologies and techniques for controlling these spectral side lobes, such as the use of square root raised cosine (SRRC) filtering before or during the modulation process, HPA output power back-off (OPBO), and RF filters after the HPA. Spectral mask specifications are a common method of the NTIA and ITU to define spectral occupancy power limits. They are intended to reduce interference among RF spectrum users by limiting excessive radiation at frequencies beyond the regulatory allocated bandwidth. The focus here is on the communication systems of U.S. government satellites used for space research, space operations, Earth exploration satellite services (EESS), meteorological satellite services (METSATS), and other government services. The 8025 to 8400 megahertz (MHz) X band can be used to illustrate the “unwanted emissions” issue. 8025 to 8400 MHz abuts the 8400 to 8450 MHz band allocated by the NTIA and ITU to space research for space-to-Earth transmissions such as receiving very weak Deep Space Network signals. The views and ideas expressed in this paper are those of the authors and do not necessarily reflect those of The Aerospace Corporation or The National Oceanic and Atmospheric Administration (NOAA) and its National Environmental Satellite Service (NESDIS). KEY WORDS: Unwanted emissions, RF spectrum, satellite communications, modulations, communications technology, transmitter linearization INTRODUCTION AND BACKGROUND There is a need for satellite communication systems using the RF spectrum to control “unwanted emissions,” which are defined to include out-of-band emissions (immediately adjacent band), plus spurious emissions to preclude interference to other authorized spectrum users. The ITU, through international treaty, sets standards for member nations and provides authorization for RF spectrum use beyond a nation’s boundaries. Member nations determine their own sub-allocations within the ITU regulations for their own domestic use. In the USA the NTIA regulates, coordinates, and provides authorization for agencies of the federal government to use the RF spectrum as required by federal law. Similarly, the Federal Communications Commission (FCC) regulates the nonfederal use of the radio spectrum. These organizations publish documents defining the permitted levels of both in-band and out- of-band transmitter power. The FCC and the NTIA work together in their respective domains to promote a coordinated use of the various bands within the structure of the ITU limits. The Space Frequency Coordination Group (SFCG), with input from the Consultative Committee for Space Data Systems (CCSDS), plays a significant role in advising the ITU, including proposing spectrum mask definitions to the ITU. Traditionally there has not been a great emphasis by U.S. federal government agencies to use the RF spectrum as efficiently as they might. However, due to the increasing demand for spectrum over the last few years, the spectrum use regulators have greatly increased their emphasis on efficiency. In 2003, the Department of Commerce was directed by the White House to prepare recommendations to improve spectrum management. This became part of a presidential directive on using spectrum more efficiently, titled “Improving Spectrum Management for the 21st Century.” From that paper, President George W. Bush signed a “Presidential Determination: Memorandum for the Heads of Executive Departments and Agencies.” He opens that memo, dated June 5, 2003, by stating: The existing legal and policy framework for spectrum management has not kept pace with the dramatic changes in technology and spectrum use. Under the existing framework, the Federal Government generally reviews every change in spectrum use. This process is often slow and inflexible and can discourage the introduction of new technologies. Some spectrum users, including Government agencies, have argued that the existing spectrum process is insufficiently responsive to the need to protect current critical uses. 1 Later the President wrote, 1 Presidential Memo on Spectrum Policy, Office of the Press Secretary, June 5, 2003. 2 In May 2003, I established the Spectrum Policy Initiative to promote the development and implementation of a U.S. spectrum management policy for the 21st century. This initiative will foster economic growth; promote our national and homeland security; maintain U.S. global leadership in communications technology; and satisfy other vital U.S. needs in areas such as public safety, scientific research, Federal transportation infrastructure, and law enforcement. 2 Then in the same memo he directed: the Secretary of Commerce to prepare recommendations for improving spectrum management. The Secretary of Commerce then established a Federal Government Spectrum Task Force and initiated a series of public meetings to address improvements in policies affecting spectrum use by the Federal Government, State, and local governments, and the private sector. The recommendations resulting from these activities were included in a two-part series of reports released by the Secretary of Commerce in June 2004, under the title Spectrum Policy for the 21st Century - The Presidents Spectrum Policy Initiative (Reports). Within 1 year of the date of this memorandum, the heads of agencies selected by the Secretary of Commerce shall provide agency-specific strategic spectrum plans (agency plans) to the Secretary of Commerce that include: (1) spectrum requirements, including bandwidth and frequency location for future technologies or services; (2) the planned uses of new technologies or expanded services requiring spectrum over a period of time agreed to by the selected agencies; and (3) suggested spectrum efficient approaches to meeting identified spectrum requirements.3 This was followed up by a memo from the Honorable Secretary of Commerce Carlos M. Gutierrez to the Honorable Conrad C. Lautenbacher, Jr., the Under Secretary of Commerce for Oceans & Atmosphere within NOAA, where in part he stated that: As directed by the Executive Memorandum, your agency’s plan must be submitted no later than November 30, 2005, and shall include: (1) spectrum requirements, including bandwidth and frequency location for future technologies or services; (2) the planned uses of new technologies or expanded services requiring spectrum over a period of time agreed to by the selected
Load more

Recommended publications
  • IBOC AM Transmission Specification Ibiquity Digital Corporation
    IBOC AM Transmission Specification November 2001 iBiquity Digital Corporation 8865 Stanford Boulevard, Suite 202 20 Independence Boulevard Columbia, Maryland 21045 Warren, New Jersey 07059 AM Transmission Specification © 2001 iBiquity Digital Corporation 11/08/01 Doc. No. SY_TN_5010 Rev. 01 (410) 872-1530 (908) 580-7000 Table of Contents Contents 1 SCOPE ..............................................................................................................................................................1 2 ABBREVIATIONS, SYMBOLS, AND CONVENTIONS .................................................................................1 2.1 Introduction ...............................................................................................................................................1 2.2 Abbreviations and Acronyms ....................................................................................................................1 2.3 Presentation Conventions ..........................................................................................................................1 2.4 Mathematical Symbols ..............................................................................................................................1 2.4.1 Variable Naming Conventions ..............................................................................................................1 2.4.2 Arithmetic Operators.............................................................................................................................1 2.5
    [Show full text]
  • On the Spectral and Power Requirements for Ultra-Wideband Transmission
    MITSUBISHI ELECTRIC RESEARCH LABORATORIES http://www.merl.com On the Spectral and Power Requirements for Ultra-Wideband Transmission Hongsan Sheng, Philip Orlik, Alexander M. Haimovich, Leonard J. Cimini, Jr, Jinyun Zhang TR2003-66 December 2003 Abstract UWB systems based on impulse radio have the potential to provide very high data rates over short distances. In this paper, a new pulse shape is presented that satisfies the FCC spectral mask. Using this pulse, the link budget is calculated to quantify the relationship between data rate and distance. It is shown that UWB can be a good candidate for high rate transmission over short ranges, with the capability for reliably transmitting 100 Mbps over distances at about 10 meters. IEEE International Conference on Communications (ICC) This work may not be copied or reproduced in whole or in part for any commercial purpose. Permission to copy in whole or in part without payment of fee is granted for nonprofit educational and research purposes provided that all such whole or partial copies include the following: a notice that such copying is by permission of Mitsubishi Electric Research Laboratories, Inc.; an acknowledgment of the authors and individual contributions to the work; and all applicable portions of the copyright notice. Copying, reproduction, or republishing for any other purpose shall require a license with payment of fee to Mitsubishi Electric Research Laboratories, Inc. All rights reserved. Copyright c Mitsubishi Electric Research Laboratories, Inc., 2003 201 Broadway, Cambridge, Massachusetts 02139 MERLCoverPageSide2 On the Spectral and Power Requirements for Ultra-Wideband Transmission Hongsan Sheng† Philip Orlik‡ Alexander M. Haimovich† Leonard J.
    [Show full text]
  • NRSC-5 RF Mask Compliance: Measurement Methods and Practice April, 2009
    NRSC GUIDELINE NATIONAL RADIO SYSTEMS COMMITTEE NRSC-G201 NRSC-5 RF Mask Compliance: Measurement Methods and Practice April, 2009 NAB: 1771 N Street, N.W. CEA: 1919 South Eads Street Washington, DC 20036 Arlington, VA 22202 Tel: (202) 429-5356 Fax: (202) 775-4981 Tel: (703) 907-7660 Fax: (703) 907-8113 Co-sponsored by the Consumer Electronics Association and the National Association of Broadcasters http://www.nrscstandards.org NRSC-G201 NOTICE NRSC Standards, Guidelines, Reports and other technical publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for his particular need. Existence of such Standards, Guidelines, Reports and other technical publications shall not in any respect preclude any member or nonmember of the Consumer Electronics Association (CEA) or the National Association of Broadcasters (NAB) from manufacturing or selling products not conforming to such Standards, Guidelines, Reports and other technical publications, nor shall the existence of such Standards, Guidelines, Reports and other technical publications preclude their voluntary use by those other than CEA or NAB members, whether to be used either domestically or internationally. Standards, Guidelines, Reports and other technical publications are adopted by the NRSC in accordance with the NRSC patent policy. By such action, CEA and NAB do not assume any liability to any patent owner, nor do they assume any obligation whatever to parties adopting the Standard, Guideline, Report or other technical publication. This Guideline does not purport to address all safety problems associated with its use or all applicable regulatory requirements.
    [Show full text]
  • Bandwidth-Efficient Modulations Summary of Definition, Implementation, and Performance
    Report Concerning Space Data System Standards BANDWIDTH-EFFICIENT MODULATIONS SUMMARY OF DEFINITION, IMPLEMENTATION, AND PERFORMANCE INFORMATIONAL REPORT CCSDS 413.0-G-2 GREEN BOOK October 2009 Report Concerning Space Data System Standards BANDWIDTH-EFFICIENT MODULATIONS SUMMARY OF DEFINITION, IMPLEMENTATION, AND PERFORMANCE INFORMATIONAL REPORT CCSDS 413.0-G-2 GREEN BOOK October 2009 CCSDS REPORT CONCERNING BANDWIDTH-EFFICIENT MODULATIONS AUTHORITY Issue: Informational Report, Issue 2 Date: October 2009 Location: Washington, DC, USA This document has been approved for publication by the Management Council of the Consultative Committee for Space Data Systems (CCSDS) and reflects the consensus of technical panel experts from CCSDS Member Agencies. The procedure for review and authorization of CCSDS Reports is detailed in the Procedures Manual for the Consultative Committee for Space Data Systems. This document is published and maintained by: CCSDS Secretariat Space Communications and Navigation Office, 7L70 Space Operations Mission Directorate NASA Headquarters Washington, DC 20546-0001, USA CCSDS 413.0-G-2 Page i October 2009 CCSDS REPORT CONCERNING BANDWIDTH-EFFICIENT MODULATIONS FOREWORD This Report contains technical material to supplement the CCSDS recommendations for the standardization of modulation methods for high symbol rate transmissions generated by CCSDS Member Agencies. Through the process of normal evolution, it is expected that expansion, deletion, or modification of this document may occur. This Report is therefore subject to CCSDS document management and change control procedures, which are defined in the Procedures Manual for the Consultative Committee for Space Data Systems. Current versions of CCSDS documents are maintained at the CCSDS Web site: http://www.ccsds.org/ Questions relating to the contents or status of this document should be addressed to the CCSDS Secretariat at the address indicated on page i.
    [Show full text]
  • New Methods for HD Radio™ Crest Factor Reduction and Pre-Correction
    New Methods for HD Radio Crest Factor Reduction and Pre-correction April 12, 2015 NAB Show 2015 Featuring GatesAir’s Tim Anderson Kevin Berndsen Radio Product & Business Senior Signal Development Manager Processing Engineer Copyright © 2015 GatesAir, Inc. All rights reserved. New Methods for HD Radio Crest Factor Reduction and Pre-correction Timothy Anderson, CPBE Radio Product Development Manager, GatesAir Kevin Berndsen, MSEE Senior Signal Processing Engineer, GatesAir NAB 2015 Broadcast Engineering Conference Crest Factor and Intermodulation Distortion The biggest challenge in amplifying orthogonal frequency-division multiplexed (OFDM) waveforms used for HD Radio and all other digital radio formats is: a) High Crest Factor of multiple carriers. b) Intermodulation products of multiple carriers Crest Factor vs. Peak-Average Power Ratio . Crest factor is a measure of a waveform, such as alternating current, sound or complex RF waveform, . As a power ratio, PAPR is showing the ratio of peak values to the normally expressed in average value. decibels (dB). Crest Factor is defined as the peak . When expressed in decibels, amplitude of the waveform divided by Crest Factor and PAPR are the RMS value of the waveform equivalent . The peak-to-average power ratio (PAPR) is the peak amplitude squared (giving the peak power) divided by the RMS value squared (giving the average power). It is the square of the crest factor Peak Distribution . The Hybrid HD Radio™ system uses up to 534 Orthogonal Frequency Division Multiplexed (OFDM) subcarriers modulated at equally spaced frequencies and 90 degrees to one another. Statistically, with this number of orthogonally opposed subcarriers, there can and will occasionally be very high amplitude peaks due to vector summation of the carriers.
    [Show full text]
  • APPENDIX a Frequency Considerations for Telemetry
    Telemetry Standards, IRIG Standard 106-15 (Part 1), Appendix A, July 2015 APPENDIX A Frequency Considerations for Telemetry Acronyms ................................................................................................................................... A-iii 1.0 Purpose ...................................................................................................................... A-1 2.0 Scope ......................................................................................................................... A-1 2.1 Definitions........................................................................................................... A-1 2.2 Modulation methods ........................................................................................... A-2 2.3 Other Notations ................................................................................................... A-2 3.0 Authorization to Use a Telemetry System ................................................................ A-2 3.1 RF Spectrum Support Certification .................................................................... A-3 3.2 Frequency Authorization .................................................................................... A-4 4.0 Frequency Usage Guidance ...................................................................................... A-4 4.1 Minimum Frequency Separation ......................................................................... A-4 4.2 Alternative method for determining frequency separation ................................
    [Show full text]
  • EN 302 623 V0.3.2 (2008-05) Harmonized European Standard (Telecommunications Series)
    Draft ETSI EN 302 623 V0.3.2 (2008-05) Harmonized European Standard (Telecommunications series) Broadband Wireless Access Systems (BWA) in the 3 400 MHz to 3 800 MHz frequency band; Mobile Terminal Stations; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive 2 Draft ETSI EN 302 623 V0.3.2 (2008-05) Reference DEN/BRAN-0060002 Keywords access, broadband, BWA, mobile, terminal ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88 Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission.
    [Show full text]
  • Spectral Re-Growth Was Coined to Describe Intermodulation Products Generated When a Digital Transmitter Is Added to an Analog Transmission System
    Shively Labs® Spectral Regrowth Abstract Intermodulation products, or spurs, can develop within the analog and digital transmitters in combined systems using high-level injection. In some cases, spurs can result in sub-optimal signal quality or even cause stations to interfere with each other’s signals. The term spectral re-growth was coined to describe intermodulation products generated when a digital transmitter is added to an analog transmission system. In the early days of digital implementation, external filtering was often used to eliminate or reduce interference. As the technology has evolved, however, only subtle adjustments to the system, such as the addition of a fine-match- ing transformer to the dummy load, have proven necessary to reduce distortion and interference to meet the FCC’s digital FM mask. There are two sets of spurs that have to be dealt with. The first set of spurs is generated within a digital transmitter as the two sidebands interact. The second set of spurs is also generated in the digital transmitter and is a product of each digital sideband combining with the analog signal. The signal level of these spurs is a function of the isola- tion between the analog and digital transmitters. This paper provides a basic overview of how high-level injectors work, their weaknesses, and how they can best be optimized, as is essential to the design, installation, tuning and operation of a modern analog/digital FM station. Document No. tb-spectral_regrowth (150320) A Division of Howell Laboratories, Inc., P. O. Box 389, Bridgton, Maine 04009 USA www.shively.com (207) 647-3327 1-888-SHIVELY Fax: (207)647-8273 [email protected] An Employee-Owned Company Certifi ed to ISO-9001 Spectral Regrowth The FCC digital mask The characteristic FM analog/digital mask is shown in Figure 1.
    [Show full text]
  • Multidimensional Waveform Shaping in Multicarrier Systems Ertugrul Guvenkaya University of South Florida, [email protected]
    University of South Florida Scholar Commons Graduate Theses and Dissertations Graduate School 11-20-2015 Multidimensional Waveform Shaping in Multicarrier Systems Ertugrul Guvenkaya University of South Florida, [email protected] Follow this and additional works at: http://scholarcommons.usf.edu/etd Part of the Communication Commons, and the Electrical and Computer Engineering Commons Scholar Commons Citation Guvenkaya, Ertugrul, "Multidimensional Waveform Shaping in Multicarrier Systems" (2015). Graduate Theses and Dissertations. http://scholarcommons.usf.edu/etd/5958 This Dissertation is brought to you for free and open access by the Graduate School at Scholar Commons. It has been accepted for inclusion in Graduate Theses and Dissertations by an authorized administrator of Scholar Commons. For more information, please contact [email protected]. Multidimensional Waveform Shaping in Multicarrier Systems by Ertu˘grulG¨uvenkaya A dissertation submitted in partial fulfillment of the requirements for the degree of Doctor of Philosophy Department of Electrical Engineering College of Engineering University of South Florida Major Professor: H¨useyinArslan, Ph.D. Richard D. Gitlin, Sc.D. Nasir Ghani, Ph.D. Yao Liu, Ph.D. Erdem Bala, Ph.D. Date of Approval: September 23, 2015 Keywords: Artificial noise, asymmetric pulse shaping, OFDM, PAPR reduction, sidelobe suppression Copyright c 2015, Ertu˘grulG¨uvenkaya DEDICATION To our martyrs. ACKNOWLEDGMENTS First, I would like to thank my advisor Dr. H¨useyin Arslan for his guidance, encouragement, and support throughout my study. I wish to thank Dr. Richard D. Gitlin, Dr. Nasir Ghani, Dr. Yao Liu, and Dr. Erdem Bala for serving in my committee and for offering valuable suggestions. I hope to be able to benefit from their profound knowledge and experience in the future, as well.
    [Show full text]
  • EVM-Constrained and Mask-Compliant MIMO
    1 EVM-Constrained and Mask-Compliant MIMO-OFDM Spectral Precoding Shashi Kant, Student Member, IEEE, Mats Bengtsson, Senior Member, IEEE, Gabor Fodor, Senior Member, IEEE, Bo Goransson,¨ Member, IEEE, and Carlo Fischione, Senior Member, IEEE the sinc functions of the OFDM signal [4]. The OOBE must Abstract—Spectral precoding is a promising technique to sup- be adequately suppressed since high OOBE causes significant press out-of-band emissions and comply with leakage constraints interference to the neighbouring adjacent channels. In practice, over adjacent frequency channels and with mask requirements on the unwanted emissions. However, spectral precoding may all OFDM systems are designed to comply not only with distort the original data vector, which is formally expressed as OOBE requirements, in terms of adjacent channel leakage the error vector magnitude (EVM) between the precoded and ratio (ACLR) and spectral emission mask, but also in-band original data vectors. Notably, EVM has a deleterious impact requirements, in terms of error vector magnitude (EVM) and on the performance of multiple-input multiple-output orthogonal other signal demodulation/detection requirements [5]. Simply, frequency division multiplexing-based systems. In this paper we propose a novel spectral precoding approach which constrains the EVM describes the distortion/noise incurred to the useful the EVM while complying with the mask requirements. We first (transmit) symbols and ACLR represents the amount of un- formulate and solve the EVM-unconstrained mask-compliant desired power that exists in the neighbouring carriers relative spectral precoding problem, which serves as a springboard to to the desired carrier power—the detailed description of these the design of two EVM-constrained spectral precoding schemes.
    [Show full text]
  • A Critique of Fcc's Tv White Space Regulations
    [STANDARDS] Ramachandran Ramjee Microsoft Research India Sumit Roy University of Washington USA Krishna Chintalapudi Microsoft Research USA Editor: Michelle Gong A CRITIQUE OF FCC’S TV WHITE SPACE REGULATIONS roadband access constitutes the “oxygen” for the Internet Era, to which end, the issue of spectrum management is foundational. In this position paper, we present an overview Bof FCC’s pioneering work framing TV white space rules that allows unlicensed access by secondary users while protecting licensed primary users. The core contribution of this paper is an in-depth analysis of FCC’s TV white space regulations (often treated as a global template). We argue that FCC’s current white space regulations does not achieve the desired balance between effectively promoting unlicensed secondary access and providing adequate protection of the primary. As more countries around the world look at framing white space regulations, we argue for incorporating a more flexible design that can catalyze a white space device ecosystem to flourish, similar to Wi-Fi. INTRODUCTION network services, based on the operators Broadly speaking, spectrum allocations belief that exclusive rights to spectrum can be classified under two principles/ enables them to offer/tailor desired approaches: services, as well as optimize the network/ delivery mechanisms so as to extract a) granting of exclusive licenses, usually via maximum revenue. The unlicensed model a suitably designed auction mechanism, is used by standards, such as Wi-Fi, to operators for an explicitly identified where the fundamental issue is managing purpose of service (that may not be interference, specifically a) secondary changed) and unlicensed interference to primary b) setting aside “unlicensed bands” for licensed users and b) interference between technology neutral usage, whereby unlicensed secondary users.
    [Show full text]
  • EN 302 063 V1.1.1 (2003-01) European Standard (Telecommunications Series)
    ETSI EN 302 063 V1.1.1 (2003-01) European Standard (Telecommunications series) Fixed Radio Systems; Multipoint equipment; Multipoint digital radio systems operating in the 31,0 GHz to 33,4 GHz (32 GHz) frequency range 2 ETSI EN 302 063 V1.1.1 (2003-01) Reference DEN/TM-04116 Keywords FWA, multipoint, radio, DFRS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88 Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, send your comment to: [email protected] Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
    [Show full text]