DOCSLIB.ORG

Modification Bulletins: Bellini-C3, B-C3 (B234/B235/B236), Aficio

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Modification Bulletins: Bellini-C3, B-C3 (B234/B235/B236), Aficio Modification Bulletin PAGE: 1/1 Model: Bellini-C3 Date:05-Jul-06 No.: MB234001 Modified Article: TONER BANK CASE Prepared by: S. Ishizu From: 2nd Tech. Support Sec. Service Support Dept. Reason for Parts catalog correction Vendor change Other Modification: To facilitate assembly To improve reliability To meet standards Part standardization Product Safety (RoHs compliant) Old part New part Description Q’ty Int Page Index Note number number B0703313 B2343311 TONER BANK CASE 1 O/O 83 8 1 Change: The materials for these parts were changed. Reason: To comply with the RoHS Directive. Note: The functions of these parts were not changed. IMPORTANT: l The materials for the parts were changed before the part numbers were changed. To make sure the correct parts are used on the correct machines, please handle the parts as follows: Parts with the old P/N: Non-RoHS compliant parts Parts with the new P/N: RoHS compliant parts RoHS Non-RoHS Compliant Parts Compliant Parts RoHS Compliant Machines OK DO NOT USE Non-RoHS Compliant Machines OK OK l Continue using non-RoHS compliant parts on non-ROHS compliant machines until the stock of these parts runs out. Then, start using RoHS compliant parts on the non-RoHS compliant machines. l DO NOT use non-RoHS compliant parts on RoHS compliant machines. Note: This is to make sure that all machines are in full compliance with the RoHS Directive. Modification Bulletin PAGE: 1/1 Model:Bellini-C3 Date: 05-Jul-06 No.: MB234002 Modified Article: Stopper Bracket Prepared by: S. Ishizu From: 1st Tech. Support Sec. Service Support Dept. Reason for Parts catalog correction Vendor change Other Modification: To facilitate assembly To improve reliability To meet standards Part standardization Product Safety (RoHs compliant) Old part New part Description Q’ty Int Page Index Note number number A2944104 B2344109 Stopper Bracket 1 O/O 107 9 1 Change: The materials for these parts were changed. Reason: To comply with the RoHS Directive. Note: The functions of these parts were not changed. IMPORTANT: l The materials for the parts were changed before the part numbers were changed. To make sure the correct parts are used on the correct machines, please handle the parts as follows: Parts with the old P/N: Non-RoHS compliant parts Parts with the new P/N: RoHS compliant parts RoHS Non-RoHS Compliant Parts Compliant Parts RoHS Compliant Machines OK DO NOT USE Non-RoHS Compliant Machines OK OK l Continue using non-RoHS compliant parts on non-ROHS compliant machines until the stock of these parts runs out. Then, start using RoHS compliant parts on the non-RoHS compliant machines. l DO NOT use non-RoHS compliant parts on RoHS compliant machines. Note: This is to make sure that all machines are in full compliance with the RoHS Directive. Modification Bulletin PAGE: 1/1 Model:Bellini-C3 Date: 05-Jul-06 No.: MB234003 Modified Article: THERMISTOR: FUSING: ASS’Y Prepared by: S. Ishizu From: 2nd Tech. Support Sec. Service Support Dept. Reason for Parts catalog correction Vendor change Other Modification: To facilitate assembly To improve reliability To meet standards Part standardization Product Safety (RoHs compliant) Old part New part Description Q’ty Int Page Index Note number number A2294131 B2344131 THERMISTOR: FUSING: ASS’Y 1 O/O 111 2 1 Change: The materials for these parts were changed. Reason: To comply with the RoHS Directive. Note: The functions of these parts were not changed. IMPORTANT: l The materials for the parts were changed before the part numbers were changed. To make sure the correct parts are used on the correct machines, please handle the parts as follows: Parts with the old P/N: Non-RoHS compliant parts Parts with the new P/N: RoHS compliant parts RoHS Non-RoHS Compliant Parts Compliant Parts RoHS Compliant Machines OK DO NOT USE Non-RoHS Compliant Machines OK OK l Continue using non-RoHS compliant parts on non-ROHS compliant machines until the stock of these parts runs out. Then, start using RoHS compliant parts on the non-RoHS compliant machines. l DO NOT use non-RoHS compliant parts on RoHS compliant machines. Note: This is to make sure that all machines are in full compliance with the RoHS Directive. Modification Bulletin PAGE: 1/1 Model:Bellini-C3 Date:06-Jul-06 No.: MB234004 Modified Article: PAPER FEED BASE Prepared by: S. Ishizu From: 2nd Tech. Support Sec. Service Support Dept. Reason for Parts catalog correction Vendor change Other Modification: To facilitate assembly To improve reliability To meet standards Part standardization Product Safety (RoHs compliant) Old part New part Description Q’ty Int Page Index Note number number A8061231 B3011232 PAPER FEED BASE 1 O/O 31 27 1 Change: The materials for these parts were changed. Reason: To comply with the RoHS Directive. Note: The functions of these parts were not changed. IMPORTANT: l The materials for the parts were changed before the part numbers were changed. To make sure the correct parts are used on the correct machines, please handle the parts as follows: Parts with the old P/N: Non-RoHS compliant parts Parts with the new P/N: RoHS compliant parts RoHS Non-RoHS Compliant Parts Compliant Parts RoHS Compliant Machines OK DO NOT USE Non-RoHS Compliant Machines OK OK l Continue using non-RoHS compliant parts on non-ROHS compliant machines until the stock of these parts runs out. Then, start using RoHS compliant parts on the non-RoHS compliant machines. l DO NOT use non-RoHS compliant parts on RoHS compliant machines. Note: This is to make sure that all machines are in full compliance with the RoHS Directive. MB234005 Modification Bulletin PAGE: 1/1 Model:Bellini-C3 Date:06-Jul-06 No.: MB234005 Modified Article: Toner Bottle Shaft Prepared by: S. Ishizu From: 2nd Tech. Support Sec. Service Support Dept. Reason for Parts catalog correction Vendor change Other Modification: To facilitate assembly To improve reliability To meet standards Part standardization Product Safety (RoHs compliant) Old part New part Description Q’ty Int Page Index Note number number A2943352 B2343356 Toner Bottle Shaft 1 X/O 83 25 1 Change: The materials for these parts were changed. Reason: To comply with the RoHS Directive. Note: The functions of these parts were not changed. IMPORTANT: l The materials for the parts were changed before the part numbers were changed. To make sure the correct parts are used on the correct machines, please handle the parts as follows: Parts with the old P/N: Non-RoHS compliant parts Parts with the new P/N: RoHS compliant parts RoHS Non-RoHS Compliant Parts Compliant Parts RoHS Compliant Machines OK DO NOT USE Non-RoHS Compliant Machines OK OK l Continue using non-RoHS compliant parts on non-ROHS compliant machines until the stock of these parts runs out. Then, start using RoHS compliant parts on the non-RoHS compliant machines. l DO NOT use non-RoHS compliant parts on RoHS compliant machines. Note: This is to make sure that all machines are in full compliance with the RoHS Directive. Modification Bulletin PAGE: 1/1 Model: Bellini-C3 (Katana) Date: 17-Oct-06 No.: MB234006 Modified Article: Toner Bank: Main Prepared by: S. Ishizu From: 2nd Tech. Support Sec. Service Support Dept. Reason for Parts catalog correction Vendor change Other Modification: To facilitate assembly To improve reliability To meet standards Part standardization Product Safety ( ) The following part number has been corrected. Incorrect part Correct part Description Q’ty Page Index Note number number B2343300 - Toner Bank Unit 77 * - B2343305 Toner Bank: Main 1 77 * A2943296 Gear: 108Z 81 11 A2943293 Gear: 108Z 2 81 11 Modification Bulletin PAGE: 1/2 Model: Bellini-C3(Katana) Date: 17-Oct-06 No.: MB234007 Modified Article: Tray Heater Kit Prepared by: S. Ishizu From: 2nd Tech. Support Sec. Service Support Dept. Reason for Parts catalog correction Vendor change Other Modification: To facilitate assembly To improve reliability To meet standards Part standardization Product Safety The following Tray Heater Kits are newly registered as service parts New part Description Q’ty Page Index Note number B2346191 Lower Tray Heater Kit 1 171 16 B2346190 Upper Tray Heater Kit 1 173 26 NOTE: If you install above, the following kits and part are needed: · Upper Tray Heater Kit (B2346190): 1 pcs · Lower Tray Heater Kit (B2346191): 1 pcs · Tapping Screw: 4 x 8(04514008N): 7 pcs B2346191 (Lower Tray Heater Kit) 1 0 1 1 0 1 1 0 1 1 0 1 1 4 1 4 1 0 1 9 1 0 1 1 3 1 0 1 9 1 0 1 1 3 1 0 1 1 0 1 1 0 1 1 0 1 1 0 1 1 5 1 0 1 1 0 1 1 0 1 1 0 1 5 1 0 1 1 1 0 2 6 1 2 4 1 0 1 1 0 3 1 0 1 1 0 4 1 0 3 2 7 1 0 1 1 0 1 1 0 1 3 1 0 1 1 0 7 1 0 1 1 0 1 0 5 1 1 OPTION 16 Modification Bulletin PAGE: 2/2 Model: Bellini-C3(Katana) Date: 17-Oct-06 No.: MB234007 B2346190 (Upper Tray Heater Kit) Modification Bulletin PAGE: 1/1 Model: Bellini-C3(Katana) Date: 15-Nov-06 No.: MB234008 Modified Article: Spring Support Plate Prepared by: S. Ishizu From: 2nd Tech. Support Sec. Service Support Dept. Reason for Parts catalog correction Vendor change Other Modification: To facilitate assembly To improve reliability To meet standards Part standardization Product Safety ( ) Incorrect part Correct part Description Q’ty Page Index Note number number B2343400 Cylinder Unit B2343340 Spring Support Plate 1 83 19 Change/Reason: The part number and description in the Parts Catalog were corrected.
Load more

Recommended publications
  • Photocopier Industry: at the Forefront of Servitization
    View metadata, citation and similar papers at core.ac.uk brought to you by CORE provided by Florence Research Photocopier industry: at the forefront of servitization. Filippo Visintin Abstract The photocopier industry is undoubtedly one of the forerunners of servitization. The original equipment manufacturers (OEMs) of photocopiers, such as Xerox, pi- oneered the implementation of servitised business models and, over time, have de- veloped considerable system-integration, application-development and consulting capabilities. Today, these companies integrate print needs within total ICT solutions and com- pete against system integrators, consulting firms and software vendors in a large, diverse and growing document management market. This chapter provides a state of the art analysis of servitization phenomenon in the industry as well as a retro- spective analysis of its evolution. The chapter ends with a discussion of managerial implications. xy.1 Introduction The photocopier industry is one of the forerunners of servitization (Finne et al. 2013, Matsumoto and Kamigaki 2012). The original equipment manufacturers (OEMs) of photocopiers have profited from the sales of services and consumables and pioneered the implementation of servitised business models that are now com- mon practice in many other industries. For example, some of the challenges that photocopier OEMs have faced well in advance of many other manufacturers include the sale of the products’ usage instead of the products themselves, the adoption of pay-per-output (pay-per-page) pricing models and the delivery of integrated solu- tions and outsourcing services (Finne et al. 2013; Visintin 2012). Today, formerly analogue photocopier OEMs produce connected and digital multifunction devices. Under the heading of managed print services, they also offer integrated solutions that claim to optimise the customer’s document-related pro- cesses and infrastructure.
    [Show full text]
  • Technical Bulletins: General
    Reissued on April 30, 1991 Technical Bulletin No. RTB-003 SUBJECT: Corona Casing Cleaning DATE:April 30,1991 PAGE: 1 of 1 PREPARED BY: M. Kitajima FROM: Copier Technical Support Section CHECKED BY: CLASSIFICATION: MODEL: General Action Required Revision of service manual Troubleshooting Information only Retrofit Information Other This bulletin gives information on cleaning the corona casing. CLEANING Section Action at EM/PM Casing Clean with water first and with alcohol if toner still remains. End Block Clean with a blower brush and then with alcohol. EXPLANATION The corona discharge causes ammonium nitrate (NH4NO3) to accumulate on the corona casing. NH4NO3 functions as an insulator that reduces the corona discharge to the casing. The power pack responds by increasing the voltage to the corona wire in order to maintain a constant current output. (The power pack is a constant current type.) If toner or some other material accumulates inside the corona end block especially inside the hook groove [A], it may cause an electrical leak under humid conditions. NH4NO3 can be easily removed with water but not with alcohol. Toner can be easily removed with alcohol but not with water. Therefore, be careful to use the proper cleaning method for each corona unit section. [A] REVISED ON APRIL 15, 1991 Technical Bulletin No. RTB-005 SUBJECT: Cleaning Solutions DATE: Dec. 30, ’90 PAGE: 1 of 1 PREPARED BY: T. OKAJIMA FROM: International Q.A. Center CHECKED BY: CLASSIFICATION: MODEL: General Action Required Revision of service manual Troubleshooting Information only Retrofit Information Other Based upon the request from the market, three type of cleaning solution have been registered as service parts.
    [Show full text]
  • Uninet Catalog 2008-2009
    www.uninetimaging.com CATALOG 2008/2009 TABLE OF CONTENTS TABLE OF CONTENTS COMPANY INFORMATION PRODUCTS BY ENGINE About UniNet 3 Apple® / Avision® / Brother® 63 Worldwide Locations 5 Canon® 69 Company History 6 Casio® 88 Sales Team / Distribution / R&D 9 Compaq® / Dataproducts® / Dell® 89 Technical Support / Environmental Policy 10 Epson® 93 Social Consciousness 11 Fujitsu® / GCC® / Gestetner® 106 Product Brands 12 HP® 107 IBM® 133 CLIENT FORMS Konica Minolta® 137 Terms & Conditions 17 Kyocera® 138 Credit Card Authorization 19 Lanier® 142 TeleCheck Request Form 21 Lexmark® 143 Client Survey 23 LG / Minolta® 157 Mita® 167 TECHNICAL GUIDES Muratec® / Nashuatec® / NEC® 169 Common Cartridge Failures 27 Okidata® 171 Cartridge Printing Theory 29 Olivetti® / Others 179 Cartridge Cleaning Methods 49 Panafax® 180 Chemical Solvent Table 51 Panasonic® 181 Black Laser Repetitive Defect Chart 53 Pentax / Pitney Bowes / QMS 184 Color Laser Repetitive Defect Chart 57 Ricoh® 186 STMC Product Data - Blended™ HP® 60 Samsung® 197 STMC Product Data - Blended™ Lexmark® 62 Savin® / Sharp® 207 Sindo Ricoh® 212 Source Technologies® / Tally Genicom® 213 TEC® / Tektronix® / Telecom® / Toshiba® 214 Triumph Adler® / Xante® 220 Xerox® 221 TOOLS & SUPPLIES Coatings, Chemicals & Tools 244 Packaging UniNet 246 UniNet Imaging Inc. • Ph + 1.310.280.9620 • Fx + 1.310.838.7294 • [email protected] • www.uninetimaging.com 1 COMPANY INFORMATION ABOUT UNINET ABOUT UNINET UniNet Imaging Inc. is a worldwide quality manufacturer and solutions provider to OEMs and remanufacturers, as well as a dis- tributor of printer toner, smartchips, and cartridge recycling components. UniNet offers a wide and complete selection of its brand name products consisting of Absolute COLOR™ Toners, Absolute Black Blended™ Toners, Unichips™ powered by Summit Technologies, Unidrums™ and Unirollers™.
    [Show full text]
  • Find Your Workflow
    Mobility ECM Imaging Supplies Big Data Automation Service & Repair Storage Solutions BPO Network Serices Hardware Applications Integration New Technologies. New Applications. New Show. Security Power Management Leasing Solutions Software MPS Cloud Solutions Information Management Capture Technology Mobility ECM Imaging Supplies Mobility ECM Imaging Supplies Big Data Automation Service & Repair Storage Solutions BPO Network Serices Hardware Applications Integration Security Power Management Leasing Solutions Software MPS Cloud Solutions Information Management Capture Technology Mobility ECM Imaging Supplies Mobility ECM Imaging Supplies Big Data Automation Service & Repair Storage Solutions BPO Network Serices Hardware Applications Integration Security Power Management Leasing Solutions Software MPS Cloud Solutions Information Management Capture Technology Mobility ECM Imaging Supplies Mobility ECM Imaging Supplies Big Data Dec.Automation 10-12, 2013 Service & Repair Storage Solutions BPO Network Serices HardwareShow Guide Applications Integration Security Power Management Leasing Solutions Software MPS Cloud Solutions Information Management Capture Technology Mobility ECM Imaging Supplies Mobility ECM Imaging Supplies Big Data Automation Service & Repair Storage Solutions BPO Network Serices Hardware Applications Integration Security Power Management Leasing SolutionsFIND Software MPS Cloud Solutions Information Management Capture TechnologyYOUR Mobility ECM Imaging Supplies ECM Imaging Supplies Big Data AutomationWORKFLOW Service & Repair Storage Solutions BPO Network Serices Hardware Applications Integration Se- BusinessImagingExpo.com curity Power Management Leasing Solutions Software MPS Cloud Solutions Information Management Capture Technology Mobility ECM Imaging Supplies Conference Hours: Managed Print Summit Workfl ow Summit Exhibit Hall Hours Expo Education Mobility ECMTuesday 8:30 a.m.Imaging - 5:30 p.m. SuppliesTuesday 8:30 a.m. - 5:30 p.m.Big DataWednesday 11:00 a.m.Automation - 5:00 p.m.
    [Show full text]
  • Bliq Is the Most Comprehensive Source of Independent Research, Data and Analysis in the Industry
    Research. Tools. Analysis. bliQ is the most comprehensive source of independent research, data and analysis in the industry. With a hardware database of over 50,000 document imaging devices and a robust database of document imaging software, bliQ helps you understand your products and the competition, while automating time-consuming daily workflows. © Keypoint Intelligence | 1 bliQ Research Tools Analysis © Keypoint Intelligence | 2 BLI Research Hardware Specifications Over 50,000 product specs in bliQ which includes hundreds of spec fields (MSRP, part numbers, predecessor/successor, supplies, options etc.). Product Photos View hundreds of OEM provided product photos and photos taken during testing. Manufacturer Literature Access product sheets, press releases, user guides, and brochures on individual devices. © Keypoint Intelligence | 3 BLI Research Software Specifications Over 1,000 product specs in the database on document management, print management, mobile printing, cost accounting, MFP apps etc. including pricing and hard-to-find feature information. Product Briefs Detailed overviews that highlight key features, target markets and more. Photo Gallery Screenshots of tested products. Manufacturer Literature Access product sheets, press releases, user guides, and brochures on individual devices. © Keypoint Intelligence | 4 BLI Tools My bliQ My bliQ is a new dashboard where you can access your saved content and favorite tools. • Search for products right from the home screen by using the Product Search box • Access your saved content,
    [Show full text]
  • Uninetcatalog.Pdf
    TABLE OF CONTENTS COMPANY PROFILE About UniNet 3 Worldwide Locations 4 Company History 5 Sales and Distribution 9 R&D and Technical Support 10 Environmental Consciousness 11 Social Consciousness 12 Product Brands 16 TECHNICAL GUIDES Common Cartridge Failures 23 Cartridge Printing Theory 25 Cartridge Cleaning Methods 45 Chemical Solvent Table 46 Black Laser Repetitive Defect Chart 47 Color Laser Repetitive Defect Chart 51 CLIENT FORMS Terms & Conditions/How to Place an Order 53 Credit Card Authorization 55 Telecheck Request Form 56 Client Survey 57 PRODUCT CATALOG New Product List 2010 59 Catalog by Engine 78 www.uninetimaging.com © 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only. “Under Development” and/or “Under Final Test” samples are not under UniNet warranty and are for developing purposes only. COMPANY PROFILE ABOUT UNINET UniNet Imaging Inc. is a worldwide quality manufacturer and solutions provider to OEMs and remanufacturers, as well as a distributor of printer toner, smartchips and cartridge recycling components. UniNet offers a wide and complete selection of its brand name products consisting of Absolute COLOR™ toners, Absolute Black® toners, Unichips™, ASiC Smartchips™ and Universal Superchips™ powered by UniNet Innovative Technologies, Unidrums™ and Unirollers™. UniNet’s product line includes wiper blades, PCRs, MAG rollers and doctor blades among others. MISSION STATEMENT “At UniNet, we Guide, Protect and Care for our clients.” We Guide our clients by showing them our strategic steps of success through our dedicated sales team providing personalized relationships. We Care about fulfilling our client's needs by improving their profitability, consistently delivering superior service, premium quality, innovative solutions, and the most complete range of products with fast and efficient delivery.
    [Show full text]
  • 1Catalog2008 2009 Web.Pdf
    www.uninetimaging.com CATALOG 2008/2009 TABLE OF CONTENTS TABLE OF CONTENTS COMPANY INFORMATION PRODUCTS BY ENGINE About UniNet 3 Apple® / Avision® / Brother® 63 Worldwide Locations 5 Canon® 69 Company History 6 Casio® 88 Sales Team / Distribution / R&D 9 Compaq® / Dataproducts® / Dell® 89 Technical Support / Environmental Policy 10 Epson® 93 Social Consciousness 11 Fujitsu® / GCC® / Gestetner® 106 Product Brands 12 HP® 107 IBM® 133 CLIENT FORMS Konica Minolta® 137 Terms & Conditions 17 Kyocera® 138 Credit Card Authorization 19 Lanier® 142 TeleCheck Request Form 21 Lexmark® 143 Client Survey 23 LG / Minolta® 157 Mita® 167 TECHNICAL GUIDES Muratec® / Nashuatec® / NEC® 169 Common Cartridge Failures 27 Okidata® 171 Cartridge Printing Theory 29 Olivetti® / Others 179 Cartridge Cleaning Methods 49 Panafax® 180 Chemical Solvent Table 51 Panasonic® 181 Black Laser Repetitive Defect Chart 53 Pentax / Pitney Bowes / QMS 184 Color Laser Repetitive Defect Chart 57 Ricoh® 186 STMC Product Data - Blended™ HP® 60 Samsung® 197 STMC Product Data - Blended™ Lexmark® 62 Savin® / Sharp® 207 Sindo Ricoh® 212 Source Technologies® / Tally Genicom® 213 TEC® / Tektronix® / Telecom® / Toshiba® 214 Triumph Adler® / Xante® 220 Xerox® 221 TOOLS & SUPPLIES Coatings, Chemicals & Tools 244 Packaging UniNet 246 UniNet Imaging Inc. • Ph + 1.310.280.9620 • Fx + 1.310.838.7294 • [email protected] • www.uninetimaging.com 1 COMPANY INFORMATION ABOUT UNINET ABOUT UNINET UniNet Imaging Inc. is a worldwide quality manufacturer and solutions provider to OEMs and remanufacturers, as well as a dis- tributor of printer toner, smartchips, and cartridge recycling components. UniNet offers a wide and complete selection of its brand name products consisting of Absolute COLOR™ Toners, Absolute Black Blended™ Toners, Unichips™ powered by Summit Technologies, Unidrums™ and Unirollers™.
    [Show full text]
  • Overview of Ricoh
    ● Ricoh Company, Ltd. Ricoh Building, 8-13-1 Ginza, Chuo-ku, Tokyo 104-8222 Japan Phone: +81-3-6278-2111 Facsimile: +81-3-6278-2997 http://www.ricoh.com/ ● Ricoh Americas Corporation 5 Dedrick Place, West Caldwell, New Jersey 07006, U.S.A. Phone: +1-973-882-2000 Facsimile: +1-973-882-2506 http://www.ricoh-usa.com/ ● Ricoh Europe PLC 66 Chiltern Street, London W1U 4AG, United Kingdom Phone: +44-20-7465-1000 Facsimile: +44-20-7224-5740 http://www.ricoh-europe.com/ ● Ricoh Asia Pacific Pte Ltd. 103 Penang Road #08-01/07, VISIONCREST Commercial, Singapore, 238467 Phone: +65-6830-5888 Facsimile: +65-6830-5830 http://www.ricoh-ap.com/ ● Ricoh China Co., Ltd. 17F., Huamin Empire Plaza, No.728 Yan An West Road, Shanghai, China Phone: +86-21-5238-0222 Facsimile: +86-21-5238-2070 http://www.ricoh.com.cn/ Investors Relations Contact ● Ricoh Company, Ltd. IR Department, Corporate Communication Center Ricoh Building, 8-13-1 Ginza, Chuo-ku, Tokyo 104-8222 Japan Phone: +81-3-6278-5254 Facsimile: +81-3-3543-9329 e-mail [email protected] http://www.ricoh.com/ir/ 2010 RICOH GROUP SUSTAINABILITY REPORT (ECONOMIC) As a good corporate citizen, the Ricoh Group continues to increase its corporate value with a three-pronged focus on economy, environment, and society. Based on the belief that economic, environmental, and social objectives are not incompatible, the Ricoh Group is committed to making meaningful contributions to the ECONOMIC creation of a sustainable society. In the course of business activities undertaken toward this end, we communicate with our stakeholders and seek their understanding and support through appropriate and timely disclosure of information on what we do and how we do it.
    [Show full text]