Univar USA Inc Safety Data Sheet

Total Page:16

File Type:pdf, Size:1020Kb

Univar USA Inc Safety Data Sheet Univar USA Inc Safety Data Sheet SDS No: Version No: Order No: 3075 Highland Pkwy, Ste 200, Downers Grove, IL 60515 (425) 889 3400 Emergency Assistance For emergency assistance involving chemicals call Chemtrec - (800) 424-9300 UNIVAR USA INC. SDS NO:10000230 ISSUE DATE:2015-05-19 VERSION:001 2015-05-19 Annotation: Univar 3075 Highland Pkwy STE 200 Downers Grove, IL 60515 425-889-3400 SAFETY DATA SHEET 1. Identification Product identifier: AROMATIC 150 (CLASS 3) Other means of identification SDS number: 000100000230 Recommended use and restriction on use Recommended use: Not available. Restrictions on use: Not known. Emergency telephone number:For emergency assistance Involving chemicals call CHEMTREC day or night at: 1-800-424-9300. CHEMTREC INTERNATIONAL Tel# 703-527-3887 2. Hazard(s) identification Hazard classification Physical hazards Flammable liquids Category 4 Health hazards Acute toxicity (Dermal) Category 4 Skin corrosion/irritation Category 2 Carcinogenicity Category 1B Environmental hazardsAcute hazards Category 3 to the aquatic environment Label elements Hazard symbol UNIVAR USA INC. SDS NO:10000230 ISSUE DATE:2015-05-19 VERSION:001 2015-05-19 Annotation: Version: 1.0 Revision date: 05/19/2015 Signal word Danger Hazard statement Combustible liquid. May cause flash fire or explosion. Harmful in contact with skin. Causes skin irritation. May cause cancer. Harmful to aquatic life. Precautionary statement Prevention Wear protective gloves/protective clothing/eye protection/face protection. Wash thoroughly after handling. Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Use personal protective equipment as required. Response IF ON SKIN: Wash with plenty of water. If skin irritation occurs: Get medical advice/attention. Call a POISON CENTER/doctor if you feel unwell. Specific treatment (see this label). Wash contaminated clothing before reuse. In case of fire: Use … to extinguish. Storage Store in well-ventilated place. Store locked up. Disposal Dispose of contents/container to an appropriate treatment and disposal facility in accordance with applicable laws and regulations, and product SDS_US - 000100000230 2/14 UNIVAR USA INC. SDS NO:10000230 ISSUE DATE:2015-05-19 VERSION:001 2015-05-19 Annotation: Version: 1.0 Revision date: 05/19/2015 characteristics at time of disposal. Other hazards which do not None. result in GHS classification 3. Composition/information on ingredients Mixtures Common name Chemical identity CAS number Content in percent (%)* and synonyms Solvent naphtha 64742-94-5 <=100% (petroleum), heavy arom. Naphthalene 91-20-3 >=9.9% 1,2,4-Trimethylbenzene 95-63-6 >=1.7% * All concentrations are percent by weight unless ingredient is a gas. Gas concentrations are in percent by volume. 4. First-aid measures Ingestion: Never give liquid to an unconscious person. Do NOT induce vomiting. Get medical attention. Inhalation: Move to fresh air. If breathing is difficult, give oxygen. Perform artificial respiration if breathing has stopped. Skin contact: Immediately flush with plenty of water for at least 15 minutes while removing contaminated clothing and shoes. Eye contact: Immediately flush with plenty of water for up to 15 minutes. Remove any contact lenses and open eyes wide apart. Most important symptoms/effects, acute and delayed Symptoms: No data available. Indication of immediate medical attention and special treatment needed Treatment: No data available. 5. Fire-fighting measures General fire hazards: No data available. SDS_US - 000100000230 3/14 UNIVAR USA INC. SDS NO:10000230 ISSUE DATE:2015-05-19 VERSION:001 2015-05-19 Annotation: Version: 1.0 Revision date: 05/19/2015 Suitable (and unsuitable) extinguishing media Suitable extinguishing Use: Water fog. Foam. Carbon dioxide or dry powder. Do not use water jet media: as an extinguisher, as this will spread the fire. Unsuitable extinguishing No data available. media: Specific hazards arising from the Vapors are flammable and heavier than air. Vapors may travel across the chemical: ground and reach remote ignition sources causing a flashback fire danger. Special protective equipment and precautions for firefighters Special fire fighting Vapors are heavier than air and may spread near ground to sources of procedures: ignition. Special protective equipment for Prevent runoff from fire control or dilution from entering streams, sewers, fire-fighters: or drinking water supply. Use water spray to cool fire exposed surfaces and to protect personnel. 6. Accidental release measures Personal precautions, protective Use personal protective equipment. equipment and emergency procedures: Methods and material for Absorb spillage with non-combustible, absorbent material. Dike for later containment and cleaning up: disposal. All equipment used when handling the product must be grounded. Eliminate sources of ignition. Prevent runoff from entering drains, sewers, or streams. Environmental precautions: Avoid release to the environment. 7. Handling and storage Precautions for safe handling: Use only with adequate ventilation. Avoid breathing mists or vapors. Avoid contact with skin. Flammable/combustible - Keep away from oxidizers, heat and flames. Conditions for safe storage, Keep container closed. Handle containers with care. Open slowly in order including any to control possible pressure release. Store in a cool, well-ventilated area. incompatibilities: SDS_US - 000100000230 4/14 UNIVAR USA INC. SDS NO:10000230 ISSUE DATE:2015-05-19 VERSION:001 2015-05-19 Annotation: Version: 1.0 Revision date: 05/19/2015 8. Exposure controls/personal protection Control parameters Occupational exposure limits Chemical identity Type Exposure Limit values Source Naphthalene TWA 10 ppm US. ACGIH Threshold Limit Values (03 2013) STEL 15 ppm US. ACGIH Threshold Limit Values (03 2013) TWA 10 ppm US. ACGIH Notice of Intended Changes (NIC) to Threshold Limit Values (03 2013) REL 10 ppm 50 mg/m3 US. NIOSH: Pocket Guide to Chemical Hazards (2010) STEL 15 ppm 75 mg/m3 US. NIOSH: Pocket Guide to Chemical Hazards (2010) PEL 10 ppm 50 mg/m3 US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000) (02 2006) TWA 10 ppm 50 mg/m3 US. OSHA Table Z-1-A (29 CFR 1910.1000) (1989) STEL 15 ppm 75 mg/m3 US. OSHA Table Z-1-A (29 CFR 1910.1000) (1989) TWA 10 ppm 50 mg/m3 US. Tennessee. OELs. Occupational Exposure Limits, Table Z1A (06 2008) STEL 15 ppm 75 mg/m3 US. Tennessee. OELs. Occupational Exposure Limits, Table Z1A (06 2008) ST ESL 200 US. Texas. Effects Screening Levels µg/m3 (Texas Commission on Environmental Quality) (02 2013) AN ESL 50 µg/m3 US. Texas. Effects Screening Levels (Texas Commission on Environmental Quality) (02 2013) ST ESL 38 ppb US. Texas. Effects Screening Levels (Texas Commission on Environmental Quality) (02 2013) AN ESL 10 ppb US. Texas. Effects Screening Levels (Texas Commission on Environmental SDS_US - 000100000230 5/14 UNIVAR USA INC. SDS NO:10000230 ISSUE DATE:2015-05-19 VERSION:001 2015-05-19 Annotation: Version: 1.0 Revision date: 05/19/2015 Quality) (02 2013) TWA PEL 10 ppm 50 mg/m3 US. California Code of Regulations, Title 8, Section 5155. Airborne Contaminants (02 2012) STEL 15 ppm 75 mg/m3 US. California Code of Regulations, Title 8, Section 5155. Airborne Contaminants (02 2012) 1,2,4- TWA 25 ppm US. ACGIH Threshold Limit Values (03 Trimethylbenzene 2013) REL 25 ppm 125 US. NIOSH: Pocket Guide to Chemical mg/m3 Hazards (2010) TWA 25 ppm 125 US. OSHA Table Z-1-A (29 CFR mg/m3 1910.1000) (1989) TWA 25 ppm 125 US. Tennessee. OELs. Occupational mg/m3 Exposure Limits, Table Z1A (06 2008) ST ESL 700 US. Texas. Effects Screening Levels µg/m3 (Texas Commission on Environmental Quality) (02 2013) AN ESL 125 US. Texas. Effects Screening Levels µg/m3 (Texas Commission on Environmental Quality) (02 2013) AN ESL 25 ppb US. Texas. Effects Screening Levels (Texas Commission on Environmental Quality) (02 2013) ST ESL 140 ppb US. Texas. Effects Screening Levels (Texas Commission on Environmental Quality) (02 2013) TWA PEL 25 ppm 125 US. California Code of Regulations, mg/m3 Title 8, Section 5155. Airborne Contaminants (02 2012) Appropriate engineering Adequate ventilation should be provided so that exposure limits are not controls exceeded. Use explosion-proof ventilation equipment. Individual protection measures, such as personal protective equipment General information: No data available. Eye/face protection: If contact is likely, safety glasses with side shields are recommended. Skin protection Hand protection: Chemical resistant gloves. Other: No data available. SDS_US - 000100000230 6/14 UNIVAR USA INC. SDS NO:10000230 ISSUE DATE:2015-05-19 VERSION:001 2015-05-19 Annotation: Version: 1.0 Revision date: 05/19/2015 Respiratory protection: In case of inadequate ventilation use suitable respirator. Hygiene measures: Always observe good personal hygiene measures, such as washing after handling the material and before eating, drinking, and/or smoking. Routinely wash work clothing and protective equipment to remove contaminants. 9. Physical and chemical properties Physical state: Liquid Form: Clear Liquid Color: Colorless Odor: Aromatic Odor threshold: No data available. pH: No data available. Melting point/freezing point: -2 °C Initial boiling point and boiling range: 179 - 203 °C Flash Point: 63 °C Evaporation rate: No data available. Flammability (solid, gas): No data available. Upper/lower limit on flammability or explosive limits Flammability limit - upper (%): No data available. Flammability limit - lower (%): No data available. Explosive limit - upper (%): No data available. Explosive limit - lower (%): No data available. Vapor pressure: No data available. Vapor density: No data available. Relative density: No data available. Solubility(ies) Solubility in water: No data available. Solubility (other): No data available. Partition coefficient (n-octanol/water): No data available. Auto-ignition temperature: No data available. Decomposition temperature: No data available. Viscosity: No data available. SDS_US - 000100000230 7/14 UNIVAR USA INC. SDS NO:10000230 ISSUE DATE:2015-05-19 VERSION:001 2015-05-19 Annotation: Version: 1.0 Revision date: 05/19/2015 10. Stability and reactivity Reactivity: No data available.
Recommended publications
  • Experimental and Modeling Study of the Flammability of Fuel Tank DE-AC36-08-GO28308 Headspace Vapors from High Ethanol Content Fuels 5B
    An Experimental and Modeling Subcontract Report NREL/SR-540-44040 Study of the Flammability of October 2008 Fuel Tank Headspace Vapors from High Ethanol Content Fuels D. Gardiner, M. Bardon, and G. Pucher Nexum Research Corporation Mallorytown, K0E 1R0, Canada An Experimental and Modeling Subcontract Report NREL/SR-540-44040 Study of the Flammability of October 2008 Fuel Tank Headspace Vapors from High Ethanol Content Fuels D. Gardiner, M. Bardon, and G. Pucher Nexum Research Corporation Mallorytown, K0E 1R0, Canada NREL Technical Monitor: M. Melendez Prepared under Subcontract No. XCI-5-55505-01 Period of Performance: August 2005 – December 2008 National Renewable Energy Laboratory 1617 Cole Boulevard, Golden, Colorado 80401-3393 303-275-3000 • www.nrel.gov NREL is a national laboratory of the U.S. Department of Energy Office of Energy Efficiency and Renewable Energy Operated by the Alliance for Sustainable Energy, LLC Contract No. DE-AC36-08-GO28308 NOTICE This report was prepared as an account of work sponsored by an agency of the United States government. Neither the United States government nor any agency thereof, nor any of their employees, makes any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product, or process disclosed, or represents that its use would not infringe privately owned rights. Reference herein to any specific commercial product, process, or service by trade name, trademark, manufacturer, or otherwise does not necessarily constitute or imply its endorsement, recommendation, or favoring by the United States government or any agency thereof. The views and opinions of authors expressed herein do not necessarily state or reflect those of the United States government or any agency thereof.
    [Show full text]
  • Liquefied Natural Gas Deerfoot Consulting Inc. Liquefied Natural Gas Liquefied Methane; LNG. Fuel. Not Available. Fortisbc 16705
    Liquefied Natural Gas SAFETY DATA SHEET Date of Preparation: January 7, 2019 Section 1: IDENTIFICATION Product Name: Liquefied Natural Gas Synonyms: Liquefied Methane; LNG. Product Use: Fuel. Restrictions on Use: Not available. Manufacturer/Supplier: FortisBC 16705 Fraser Highway Surrey, BC V3S 2X7 Phone Number: Tilbury: (604) 946-4818 , Mt. Hayes: (236) 933-2060 Emergency Phone: FortisBC Gas Emergency: 1-800-663-9911 LNG Transportation Emergency: 1-877-889-2002 Date of Preparation of SDS: January 7, 2019 Section 2: HAZARD(S) IDENTIFICATION GHS INFORMATION Classification: Flammable Gases, Category 1 Gases Under Pressure - Refrigerated Liquefied Gas Simple Asphyxiant, Category 1 LABEL ELEMENTS Hazard Pictogram(s): Signal Word: Danger Hazard Extremely flammable gas. Statements: Contains refrigerated gas; may cause cryogenic burns or injury. May displace oxygen and cause rapid suffocation. Precautionary Statements Prevention: Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Wear cold insulating gloves and either face shield or eye protection. Response: Get immediate medical advice/attention. Thaw frosted parts with lukewarm water. Do not rub affected area. Leaking gas fire: Do not extinguish, unless leak can be stopped safely. In case of leakage, eliminate all ignition sources. Storage: Store in a well-ventilated place. Disposal: Not applicable. Hazards Not Otherwise Classified: Not applicable. Ingredients with Unknown Toxicity: None. This material is considered hazardous by the OSHA Hazard Communication Standard, (29 CFR 1910.1200). This material is considered hazardous by the Hazardous Products Regulations. Page 1 of 11 Deerfoot Consulting Inc. Liquefied Natural Gas SAFETY DATA SHEET Date of Preparation: January 7, 2019 Section 3: COMPOSITION / INFORMATION ON INGREDIENTS Hazardous Ingredient(s) Common name / CAS No.
    [Show full text]
  • SAFETY DATA SHEET Acetone
    SAFETY DATA SHEET Acetone Revision date: 12.05.15 SDS/004/8 Page 1 of 6 1. Identification of the substance/mixture and of the company/undertaking 1.1. Product identifier Acetone EC No. 200-662-2 1.2. Relevant identified uses of the substance or mixture and uses advised against Household Solvent 1.3. Details of the supplier of the safety data sheet Thornton & Ross Ltd, Linthwaite, Huddersfield, HD7 5QH Tel: 01484 842217 Fax: 01484 847301 Email: [email protected] 1.4 Emergency telephone number: Out of normal working hours: +44 870 8510207 2. Hazards identification 2.1. Classification of the substance or mixture According to Regulation EC 1272/2008 classified as Flammable Liquid Category 2, Eye Irritant Category 2, Specific Target Organ Toxicity Single Exposure Category 3. 2.2. Label element GHS Pictogram Signal Word Hazard Class Danger Flammable Liquids, Category 2 Eye Irritation, Category 2 Specific Target Organ Toxicity-Single Exposure, Category 3 Hazard Statements Precautionary statements H225: Highly flammable liquid and vapour. P210: Keep away from heat/sparks/open flames/hot surfaces – No smoking. H319: Causes serious eye irritation P305+351+338: IF IN EYES: Rinse cautiously with H336: May cause drowsiness or dizziness water for several minutes. Remove contact lenses if present and easy to do – continue rinsing. P337+313: Get medical advice/attention. P403: Store in a well ventilated place. Supplemental Hazard Information (EU) EUH066: Repeated exposure may cause skin dryness or cracking 2.3. Other hazards N/A SAFETY DATA SHEET Acetone Revision date: 12.05.15 SDS/004/8 Page 2 of 6 3.
    [Show full text]
  • Material Safety Data Sheet
    SAFETY DATA SHEET EFFECTIVE JUNE 2016 SECTION 1 – PRODUCT & COMPANY IDENTIFICATION Product Name: Commercial Odorized Propane Chemical Name: Propane (C3H8) Chemical Family: Petroleum Hydrocarbon Common Names: Liquefied Petroleum Gas, LP-Gas, LPG, Bottle Gas Intended Use: Propane is a liquid fuel Distributor: Campora Propane Service, PO Box 31717 Stockton, CA 95213 Emergency Response: CHEMTREC (800) 424-9300 General Information: (209) 941-2994 SECTION 2 – CHEMICAL HAZARD CLASSIFICATION & WARNING INFORMATION Fire Hazard NFPA CLASSES: 1-Slight 2-Moderate 3-Serious Health Hazard Reactivity 4-Severe Physical hazards Flammable gases Category 1 Gases under pressure Liquefied gas Health hazards Acute toxicity, inhalation Category 4 Germ cell mutagenicity Category 1B Carcinogenicity Category 1A Reproductive toxicity Category 1A Specific target organ toxicity, repeated Category 2 exposure OSHA defined hazards Not classified. Label Elements Signal Word Danger Hazard Statement Propane (also called LPG-Liquefied Petroleum Gas or LP-Gas) is a liquid fuel stored under pressure. In most systems, propane is vaporized to a gas before it leaves the tank. Propane is highly flammable when mixed with air (oxygen) and can be ignited by many sources, including open flames, smoking materials, electrical sparks, and static electricity. Severe “freeze burn” or frostbite can result if propane liquid comes in contact with your skin. Extremely flammable gas. Harmful if inhaled. May cause genetic defects. May cause cancer. May damage fertility or the unborn child. May cause damage to Blood through prolonged or repeated exposure. May cause cryogenic burns or injury. Propane is a simple asphyxiant. Precautionary statement General Read and follow all Safety Data Sheets (SDS’S) before use.
    [Show full text]
  • An Overview of Hydrogen As a Vehicle Fuel
    Renewable and Sustainable Energy Reviews 16 (2012) 5511–5528 Contents lists available at SciVerse ScienceDirect Renewable and Sustainable Energy Reviews journal homepage: www.elsevier.com/locate/rser An overview of hydrogen as a vehicle fuel H. Fayaz a,b,n, R. Saidur a,b, N. Razali a, F.S. Anuar a,b, A.R. Saleman a,b, M.R. Islam b a Department of Mechanical Engineering, University of Malaya, Kuala Lumpur 50603, Malaysia b Centre of Research UMPEDAC, Level 4, Engineering Tower, Faculty of Engineering, University of Malaya, Kuala Lumpur 50603, Malaysia article info abstract Article history: As hydrogen fuel cell vehicles move from manifestation to commercialization, the users expect safe, Received 24 December 2010 convenient and customer-friendly fuelling. Hydrogen quality affects fuel cell stack performance and Received in revised form lifetime, as well as other factors such as valve operation. In this paper, previous researcher’s development 1 June 2012 on hydrogen as a possible major fuel of the future has been studied thoroughly. Hydrogen is one of the Accepted 4 June 2012 energy carriers which can replace fossil fuel and can be used as fuel in an internal combustion engines and as a fuel cell in vehicles. To use hydrogen as a fuel of internal combustion engine, engine design should be Keywords: considered for avoiding abnormal combustion. As a result it can improve engine efficiency, power output Hydrogen and reduce NOx emissions. The emission of fuel cell is low as compared to conventional vehicles but as Vehicle fuel penalty, fuel cell vehicles need additional space and weight to install the battery and storage tank, thus Engine increases it production cost.
    [Show full text]
  • Constants of Explosive Limits
    Constants of explosive limits Ali M. Nassimia,∗ Mohammad Jafarib, Hossein Farrokhpoura and Mohammad H. Keshavarzb aDepartment of Chemistry, Isfahan University of Technology, Isfahan 8115683111, Iran bDepartment of Chemistry, Malek Ashtar University of Technology, Shahin Shahr, 83145 115, Iran January 23, 2017 Abstract This work defines density factor as the ratio of before ignition density to after ignition density of the ignition mixture. This work provides an estimation method for explosive limits of various fuels under room temperature and pressure by showing that for a large universe of fuels, constant adiabatic flame temperature and density factor are appropriate approximations at the lower explosive limit while only a constant density factor might be an appropriate approximation at the upper explosive limit. Thus the assumption of a constant adiabatic flame temperature can be used in calculating lower explosive limit while the assumption of a constant density factor can be used in approximating upper explosive limit. Keywords: Explosive limit; Flammability limit; Adiabatic flame temperature; Density factor; LEL, UEL, LFL, UFL. List of abbreviations: Lower explosive limit (LEL), upper explosive limit (UEL), explosive limit (EL), adiabatic flame temperature (AFT), theoretical threshold temperature (TTT), Equivalence ratio (φ), Chemical Equilibrium with Applications (CEA), Constant Enthalpy and Pressure (HP), Constant internal energy and volume (UV), Lower limit flame temperature (LLFT), Upper limit flame temperature (ULFT), Limit flame temperature (LFT), Lower limit density factor (LLDF), Upper limit density factor (ULDF), Limit density factor (LDF). 1 Introduction Flammability parameters are important safety considerations in various applications ranging from the design of combustion chambers to the design of fuel tanks. Moreover, a knowledge of the flammability arXiv:1701.00909v2 [physics.chem-ph] 20 Jan 2017 parameters is used in judging fire and explosion hazards of technological processes and technological installations.
    [Show full text]
  • Hydrogen Flammability Limits and Implications on Fire Safety of Transportation Vehicles
    Hydrogen Flammability Limits and Implications on Fire Safety of Transportation Vehicles by Umit O. Koylu A University Transportation Center Program at Missouri University of Science & Technology UTC R170 Disclaimer The contents of this report reflect the views of the author(s), who are responsible for the facts and the accuracy of information presented herein. This document is disseminated under the sponsorship of the Department of Transportation, University Transportation Centers Program and the Center for Infrastructure Engineering Studies UTC program at the University of Missouri - Rolla, in the interest of information exchange. The U.S. Government and Center for Infrastructure Engineering Studies assumes no liability for the contents or use thereof. NUTC ### Technical Report Documentation Page 1. Report No. 2. Government Accession No. 3. Recipient's Catalog No. UTC R170 4. Title and Subtitle 5. Report Date Hydrogen Flammability Limits and Implications on Fire Safety of Transportation Vehicles January 2008 6. Performing Organization Code 7. Author/s 8. Performing Organization Report No. Umit O. Koylu 00013059 9. Performing Organization Name and Address 10. Work Unit No. (TRAIS) 11. Contract or Grant No. Center for Infrastructure Engineering Studies/UTC program Missouri University of Science & Technology DTRS98-G-0021 223 Engineering Research Lab Rolla, MO 65409 12. Sponsoring Organization Name and Address 13. Type of Report and Period Covered U.S. Department of Transportation Research and Special Programs Administration Final th 400 7 Street, SW 14. Sponsoring Agency Code Washington, DC 20590-0001 15. Supplementary Notes 16. Abstract The recent establishment of the National University Transportation Center at MST under the "Safe, Accountable, Flexible, Efficient Transportation Equity Act: A Legacy for Users," expands the research and education activities to include alternative transportation fuels and other issues that are at the forefront of society and the national agenda.
    [Show full text]
  • Flammability Limits: a Review with Emphasis on Ethanol for Aeronautical
    Journal of Hazardous Materials 241–242 (2012) 32–54 Contents lists available at SciVerse ScienceDirect Journal of Hazardous Materials j ournal homepage: www.elsevier.com/locate/jhazmat Review Flammability limits: A review with emphasis on ethanol for aeronautical applications and description of the experimental procedure a b,∗ c c Christian J.R. Coronado , João A. Carvalho Jr. , José C. Andrade , Ely V. Cortez , a c b Felipe S. Carvalho , José C. Santos , Andrés Z. Mendiburu a Federal University of Itajubá – UNIFEI, Mechanical Engineering Institute – IEM Av BPS 1303, Itajubá, MG CEP 37500903, Brazil b São Paulo State University – UNESP, Campus of Guaratinguetá – FEG Av. Ariberto P. da Cunha 333, Guaratinguetá, SP CEP 12510410, Brazil c National Space Research Institute – INPE, Combustion and Propulsion Laboratory – LCP Rod. Pres. Dutra, km 39, Cachoeira Paulista, SP CEP 12630-000, Brazil h i g h l i g h t s Develops a comprehensive literature review on ethanol flammability limits. Difference in standard procedures lead to different experimental values of the flammability limits. Methodology for experiments to find the FL’s of ethanol for aeronautical applications. a r t i c l e i n f o a b s t r a c t Article history: The lower and upper flammability limits of a fuel are key tools for predicting fire, assessing the possibility Received 22 May 2012 of explosion, and designing protection systems. Knowledge about the risks involved with the explo- Received in revised form 23 August 2012 sion of both gaseous and vaporized liquid fuel mixtures with air is very important to guarantee safety Accepted 16 September 2012 in industrial, domestic, and aeronautical applications.
    [Show full text]
  • Triethylene Glycol Material Safety Data Sheet (MSDS)
    3-26-02 TUE 08:57 AM DYCE CHEMICAL BLGS FAX NO, 406 248 1237 P. 02 MATERIAL SAFETY DATA SHEET Page 1 of 7 Miami cliwnlcAl lfit»m«ll»tisl MATERIAL SAFETY DATA SHEET ]rCHEMlCAL PRODUCT^ND^bMT'ANYIDTiNflFiCATlON" ^ PRODUCT NAME: Triethylene glycol HCI PRODUCT ID NUMBER: 03265 SYNONYMS: TEG, Glycol-bis(hydroxyethyl)ether CHEMICAL FAMILY NAME: Glycol NFPA HAZARD RATINGS(H-F-R) : 1-1 -0 HMIS HAZARD RATINGS(H-F-R): 1-1-0 DISTRIBUTOR: HCI USA Distribution Companies IN CASE OF EMERGENCY CALL: 1-800-424-9300 MSDS PREPARED BY: HCI Technical Resource Center St. Louis, MO 63111 (314)353-6500 2, COMPOSITION/INFORMATION ON INGREDIENTS [iNGREDiBNTS CAS... NUMBERS [Percent TriethyTenc ^lycol 000112-27-6 100 Trace impurities and additional material names not listed above may also appear in the Regulatory Information Section (Section 15) towards the end of the MSDS. These materials may be listed for local "Right to Know" compliance and for other reasons. 3: HAZARDOUS IDENTIFICATION EM ERGENCYOVERVIEWyCAUTION! May cause irritation to sHn, eyes, ancTrcspirtatory tract. Harmiu 1 if swallowed. POTENTJA L HEALTH EFFECTS: SKIN CONTACT: Brief contact is not irritating. Prolonged or repeated contact with skin may cause irritation. SKIN ABSORPTION: No data available EYES: Contact with the eyes may cause irritation. INGESTION: Ingestion may cause gastrointestinal irritation, nausea, vomiting, diarrhea, drowsiness, and loss of consciousness. May result in kidney and liver damage. INHALATION: Inhalation is believed to be minimally irritating. htlp://hciweb/QMSDS/03265.htm 4/17/01 MAR-26-02 TUE 08:57 AM DYCE CHEMICAL BLGS FAX NO, 406 248 1237 P.
    [Show full text]
  • Safety Data Sheet
    SAFETY DATA SHEET SECTION 1: Identification of the substance/mixture and of the company/undertaking 1.1. Product identifier Name of the substance Butane / Liquefied Petroleum Gas (LPG) Identification number 106-97-8 Registration number - Synonyms None. SDS number 2010 Issue date 29-July-2011 Version number 06 Revision date 24-July-2013 Supersedes date 17-August-2012 1.2. Relevant identified uses of the substance or mixture and uses advised against Identified uses Fuel. Uses advised against None known. 1.3. Details of the supplier of the safety data sheet Supplier Company name Valero Energy Ltd Address 1 Westferry Circus Canary Wharf London E14 4HA UK Telephone 01/210 345 4593 (General information; US) e-mail [email protected] Contact person Industrial Hygienist 1.4. Emergency telephone 0044/(0)18 65 407333 number SECTION 2: Hazards identification 2.1. Classification of the substance or mixture Classification according to Directive 67/548/EEC or 1999/45/EC as amended Classification F+;R12 Classification according to Regulation (EC) No 1272/2008 as amended Physical hazards Flammable gases Category 1 H220 - Extremely flammable gas. Gases under pressure Compressed gas H280 - Contains gas under pressure; may explode if heated. Health hazards Specific target organ toxicity - single Category 3 narcotic effects H336 - May cause drowsiness or exposure dizziness. Hazard summary Physical hazards Extremely flammable. Health hazards Not classified for health hazards. However, occupational exposure to the mixture or substance(s) may cause adverse health effects. Environmental hazards Not classified for hazards to the environment. Specific hazards Not available. Main symptoms May cause drowsiness or dizziness.
    [Show full text]
  • Flammability Limits, Ignition Energy and Flame Speeds in H2–CH4–NH3–N2O–O2–N2 Mixtures
    Flammability Limits, Ignition Energy and Flame Speeds in H2{CH4{NH3{N2O{O2{N2 Mixtures short title: Flammability, Ignition Energy and Flame Speed U.J. Pfahl, M.C. Ross and J.E. Shepherd Graduate Aeronautical Laboratories California Institute of Technology Pasadena, CA 91125, USA K.O. Pasamehmetoglu and C. Unal Technology & Safety Assessment Division Los Alamos National Laboratory Los Alamos, NM 87545, USA submitted as full-length article in: Combustion and Flame Revised version of March 25, 2000. corresponding author: Joseph E. Shepherd Caltech, 105-50 Pasadena, CA 91125 Phone: 626-395-3283 Fax: 626-449-2677 E-Mail: [email protected] Flammability Limits, Ignition Energy and Flame Speeds in H2{CH4{NH3{N2O{O2{N2 Mixtures U.J. Pfahl, M.C. Ross and J.E. Shepherd Graduate Aeronautical Laboratories California Institute of Technology Pasadena, CA 91125, USA K.O. Pasamehmetoglu and C. Unal Technology & Safety Assessment Division Los Alamos National Laboratory Los Alamos, NM 87545, USA Abstract Experiments on flammability limits, ignition energies, and flame speeds were carried out in a 11.25- and a 400-liter combustion vessel at initial pressures and tempera- tures of 100 kPa and 295 K, respectively. Flammability maps of hydrogen{nitrous oxide{nitrogen, methane{nitrous oxide{nitrogen, ammonia{nitrous oxide{nitrogen, and ammonia{nitrous oxide{air, as well as lean flammability limits of various hydrogen{ methane{ammonia{nitrous oxide{oxygen{nitrogen mixtures were determined. Ignition energy bounds of methane{nitrous oxide, ammonia{nitrous oxide, and ammonia{nitrous oxide{nitrogen mixtures have been determined and the influence of small amounts of oxygen on the flammability of methane{nitrous oxide{nitrogen mixtures has been inves- tigated.
    [Show full text]
  • FLAMMABILITY LIMITS of METHANE (LNG) and HYDROGEN (LH2) at EXTREME CONDITIONS, Chemical Engineering Transactions, 77, 601-606 DOI:10.3303/CET1977101 602
    601 A publication of CHEMICAL ENGINEERING TRANSACTIONS VOL. 77, 2019 The Italian Association of Chemical Engineering Online at www.cetjournal.it Guest Editors: Genserik Reniers, Bruno Fabiano Copyright © 2019, AIDIC Servizi S.r.l. ISBN 978-88-95608-74-7; ISSN 2283-9216 DOI: 10.3303/CET1977101 Flammability Limits of Methane (Lng) and Hydrogen (Lh2) at Extreme Conditions * Gianmaria Pio, Ernesto Salzano Dipartimento di Ingegneria Civile, Chimica, Ambientale e dei Materiali, Università di Bologna, via Terracini 28, 40131 Bologna (IT) [email protected] In the recent years the growing interest for cleaner and low carbon content energy sources has addressed the development of several industrial and civil applications based on methane, hydrogen, and their mixtures. The use of these gases rises, however, several technological issues for the storage and the transportation systems. Among others, cryogenic liquefaction (as liquified natural gas, LNG and liquified hydrogen, LH2) and cryo-compressed gases are considered among the most promising potential solution. On the other hand, when low and ultra-low temperature are considered, several questions regarding the safe use of such gases are raised, including the behaviour of the cold vapour phase in air after the release of liquid or cryo- compressed gas from containment system. In this work, the flammability limits of hydrogen, methane and their blends at low and ultra-low temperatures were estimated by using the laminar burning velocity obtained by means of detailed kinetic mechanism. Numerical results were compared with experimental data and empirical correlations commonly adopted for this purpose. The data agreement demonstrates the applicability of the developed procedure for the estimation of safety parameters at low and ultra-low temperature and for future technological applications, even at cryogenic conditions.
    [Show full text]