2021 Instructions

Total Page:16

File Type:pdf, Size:1020Kb

2021 Instructions www.collegehillshonda.com Accessory Application Publications No. VERSION 1 INSTALLATION FRONT UNDER SPOILERS 2021 ACCORD Issue Date P/N 08F01-TVA-100 2021 ACCORD HYBRID INSTRUCTIONS SEP 2020 PARTS LIST 2 Alcohol wipes Left front under spoiler TOOLS AND SUPPLIES REQUIRED Right front under spoiler Phillips screwdriver Pushpin Drill File 10 mm Open end wrench Masking tape 8 Female clips 3 mm, 6 mm, 8 mm, and 10 mm Drill bits Eye protection (face shield, safety goggles, etc.) Blanket Diagonal cutters The following tools are available through the Honda Tool and Equipment Program. On the iN, click on Service > Service Bay > Tool and Equipment Program, then enter 2 Long clips the number under “Search.” Or, call 888-424-6857. • Trim Tool Set (T/N SOJATP2014) • Plastic Trim Tool (T/N SILTRIMTL10) • Rubber Roller (T/N MHLE54D) 2 Short clips 2 Seals © 2020 American Honda Motor Co., Inc. – All Rights Reserved. AII14303-35 (2009) 08F01-TVA-1000-90 1 of 9 www.collegehillshonda.com Illustration of the Front Under Spoilers Installed on 2. Remove the left front grille cover and right front grille the Vehicle cover. RIGHT FRONT 3 CLIPS GRILLE COVER 3 CLIPS RIGHT FRONT UNDER SPOILER LEFT FRONT UNDER SPOILER INSTALLATION LEFT FRONT GRILLE COVER Customer Information: The information in this 3. Remove the front bumper: installation instruction is intended for use only by skilled • Apply masking tape as shown. technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your FRONT vehicle. These procedures should not be attempted by HEADLIGHT FENDER “do-it-yourselfers.” NOTE: • Be careful not to damage the body paint finish. • This kit should be installed only if the ambient air temperature is 60°F (15°C) or above. • To allow the adhesive to cure, do not wash the vehicle for 24 hours. Make sure your customer is aware of this. 1. Disconnect the negative cable from the battery, then FRONT BUMPER MASKING TAPE wait at least 3 minutes before starting work. 2 of 9 AII14303-35 (2009) © 2020 American Honda Motor Co., Inc. – All Rights Reserved. www.collegehillshonda.com • Remove the six self-tapping screws and 17 clips • With the help of an assistant, release the seven as shown. retaining tabs on each side. 6 CLIPS FRONT 3 RETAINING 6 SELF- BUMPER TABS TAPPING SCREWS CLIP (Do not reuse.) 9 CLIPS CLIP BOTTOM VIEW (Do not reuse.) CLIP CLIP 9 CLIPS (Do not reuse.) (Do not reuse.) FRONT BUMPER 4 RETAINING FRONT TABS BUMPER © 2020 American Honda Motor Co., Inc. – All Rights Reserved. AII14303-35 (2009) 3 of 9 www.collegehillshonda.com • With the help of an assistant, remove the front 4. Mark the inside of the front bumper: bumper, and unplug the vehicle connectors (if • Locate the five scribe marks on the inside of the equipped). front bumper. • Place the front bumper on a blanket. • Using a pushpin, pierce the front bumper at the five scribe marks. VEHICLE NOTE: There are several markings on the inside CONNECTORS of the front bumper. Before piercing the front (if equipped) bumper, verify you have the correct locations. Make sure to pierce the scribe marks perpendicular to the front bumper. 2 SCRIBE MARKS (Not used.) FRONT BUMPER (inside) FRONT BUMPER 5 SCRIBE MARKS PUSHPIN (Pierce perpendicular.) : 5 MARKS FRONT BUMPER 4 of 9 AII14303-35 (2009) © 2020 American Honda Motor Co., Inc. – All Rights Reserved. www.collegehillshonda.com 5. While wearing eye protection, drill the five pierced 6. Using an alcohol wipe, thoroughly clean the front marks on the front bumper to 10 mm. First, drill with bumper where the left front under spoiler will attach. a 3 mm drill bit, next, with a 6 mm drill bit, then with an 8 mm drill bit, and finish with a 10 mm drill bit. Remove any burrs. NOTE: Make sure to drill perpendicular to the front bumper. FRONT BUMPER (outside) ALCOHOL WIPE FRONT BUMPER (outside) (Clean with an alcohol wipe.) DRILL (Drill 7. Peel back the adhesive backings, and tape them to perpendicular.) the front surface of the left front under spoiler with masking tape. MASKING Temporarily TAPE attach. : 5 MARKS 3 mm 6 mm 8 mm 10 mm DRILL BITS FRONT BUMPER 6 ADHESIVE BACKINGS (Peel back.) LEFT FRONT UNDER SPOILER © 2020 American Honda Motor Co., Inc. – All Rights Reserved. AII14303-35 (2009) 5 of 9 www.collegehillshonda.com 8. Install the left front under spoiler to the front bumper. 9. Secure the left front under spoiler to the front bumper with one short clip and four female clips into each FRONT male clip as shown. BUMPER NOTE: (outside) • Make sure to install the female clips in the correct orientation. • Do not push the female clips too tight; you could deform the left front under spoiler. If necessary, readjust the female clips. FRONT Make sure there BUMPER is no gap. SEAL FEMALE CLIP LEFT FRONT MALE CLIP UNDER SPOILER FRONT LEFT FRONT BUMPER UNDER SPOILER Incorrect. MOLDING SECTION VIEW LEFT FRONT UNDER SPOILER FRONT BUMPER (inside) SHORT CLIP 3 FEMALE 3 MALE CLIPS CLIPS 6 of 9 AII14303-35 (2009) © 2020 American Honda Motor Co., Inc. – All Rights Reserved. www.collegehillshonda.com 10. Using diagonal cutters, cut off the excess of the male 11. While applying light pressure against the left front clips. under spoiler, carefully remove the adhesive backings. SEAL FRONT FEMALE BUMPER CLIP FRONT BUMPER (outside) SECTION Cut off. VIEW Line up. FRONT BUMPER (inside) LEFT FRONT 6 ADHESIVE UNDER BACKINGS SPOILER (Remove.) 12. Using a rubber roller, apply firm pressure against the left front under spoiler and roll from one end to the other. NOTE: Apply firm pressure, especially at the ends. FRONT BUMPER FRONT (outside) BUMPER Line up. FEMALE CLIP SECTION VIEW Cut off. RUBBER ROLLER LEFT FRONT UNDER SPOILER 13. Repeat steps 4 through 12 on the right side of the front bumper. © 2020 American Honda Motor Co., Inc. – All Rights Reserved. AII14303-35 (2009) 7 of 9 www.collegehillshonda.com 14. With the help of an assistant, install the front bumper. FRONT FRONT GRILLE GRILLE 15. Check that the left front grille extension and right EXTENSION EXTENSION front grille extension are properly secured to the headlights. If not secured, press the edges of the left PIN front grille extension and right front grille extension to fit the pins of the headlights as shown. PIN HEADLIGHT SECTION HEADLIGHT VIEW Press to fit the pin of the headlight. 16. Secure the left and right front under spoilers to the front bumper with the two long clips. RIGHT FRONT UNDER SPOILER 2 LONG CLIPS (supplied) FRONT LEFT BUMPER FRONT UNDER SPOILER 17. Check that all wire harnesses are routed properly and all connectors are plugged in. 8 of 9 AII14303-35 (2009) © 2020 American Honda Motor Co., Inc. – All Rights Reserved. www.collegehillshonda.com 18. Connect the negative cable to the battery. 19. Press and hold the audio unit power button for 2 seconds to restore the audio and navi (if equipped) system functions. 20. Set the clock on vehicles without navigation. 21. If necessary, restore the systems back to normal operation as described in the service information. © 2020 American Honda Motor Co., Inc. – All Rights Reserved. AII14303-35 (2009) 9 of 9.
Recommended publications
  • Tire Rule for Ponderosa (KY) Speedway | April 14, 2017 Hoosier Racing Tire: 1350, 1600 American Racer: 48, 56
    Tire Rules: Tire Rule for Ponderosa (KY) Speedway | April 14, 2017 Hoosier Racing Tire: 1350, 1600 American Racer: 48, 56 Tire Rule for Florence (KY) Speedway | April 15, 2017 Hoosier Racing Tire: 1350, 1600 American Racer: 48, 56 Tire Rule for Crossville (TN) Speedway | April 21, 2017 Hoosier Racing Tire: 1350, 1600 American Racer: 48, 56 Tire Rule for Volunteer (TN) Speedway | April 22, 2017 Hoosier Racing Tire: 1350, 1600 American Racer: 48, 56 Tire Rule for Smoky Mountain (TN) Speedway | May 4, 2017 Hoosier Racing Tire: 1350, 1600 American Racer: 48, 56 Tire Rule for Boyd's (GA) Speedway | May 26, 2017 Hoosier Racing Tire: 1350, 1600 American Racer: 48, 56 Tire Rule for Dixie (GA) Speedway | May 27, 2017 Hoosier Racing Tire: 1350, 1600 American Racer: 48, 56 Tire Rule for Rome (GA) Speedway | May 28, 2017 Hoosier Racing Tire: 1350, 1600 American Racer: 48, 56 *** Tires will be checked for soaking and by durometer for hardness before each car goes on the track for qualifying or any racing action. Weight Rules: 2350# - Open Motor 2300# - Steel Block/Aluminum Head - Spec Motor Only (8" spoiler allowed, 12" sides) 2250# - CT525 Motor (8" spoiler allowed) 2250# - All Steel Motor or Crate Motor (8" spoiler allowed, 12" sides) 1. 1# per lap burnoff + 5 lbs. in B-Mains and Feature 2. Use of a Hans Device = 30# Weight Break 3. Use of working Fire Extinguisher = 20# Weight Break Body Rules: 1. The rules and/or regulations set forth herein do not express or imply warranty of safety, from publication of, or, compliance with these rules and/or regulations.
    [Show full text]
  • Civic Jdm Rear Licence Plate Holder
    Civic Jdm Rear Licence Plate Holder Derek is clean consanguineous after crosswise Christian blob his dependant hypocritically. Achondroplastic Filip decree approximately. Caucasoid Munmro never outfrowns so obtusely or scramblings any grinders thankfully. We missing a huge selection of Genuine Honda Parts across the entire footprint of Honda models, Tomei, and accessories. If we can change according to block the size number plates do look like. JDM front end conversion with the license plate holder area shaved off? If you must wear a problem calculating your jdm engine bay sold secondhand to see and margins for authenticity in. In order to use this website and its services, and clickbait titles. Your jdm rear of a pair of this? Consumer Reports or Google Reviews. Your order to respectfully share your desire is too large to avoid vague, plastic that included. All the licence plate holder, and ukdm categories which can always have ordered has deliberately selected a pair of several cars is to. Availability: In Stock; Qty. Car & Truck Suspension & Steering Parts 96-00 Honda Civic. You have exceeded the Google API usage limit. Cox Motor Parts, please specify when ordering. Copyright the rear license plate off the actually stamped for honda? Actual product may vary. Copyright The Closure Library Authors. EBay Motors Parts Accessories Car Truck Parts DecalsEmblemsLicense Frames License Plate Frames. Product is it legal minimum of honda. All, those stroke, rear disc conversion and very much more. Honda civic rear disc brakes of your jdm front or register to eliminate any other similar bolts for the licence plate to the subreddit may not satisfied with intake for the reason.
    [Show full text]
  • (12) Ulllted States Patent (10) Patent N0.: US 8,083,260 B2 Haynes (45) Date of Patent: Dec
    US008083260B2 (12) Ulllted States Patent (10) Patent N0.: US 8,083,260 B2 Haynes (45) Date of Patent: Dec. 27, 2011 (54) COMBINATION TRUNK COVER WITH 4,376,546 A 3/1983 Guccione et a1. SPOILER AND SCROLLING DISPLAY 4,574,269 A * 3/1986 Miller ......................... .. 362/503 4,607,444 A * 8/1986 Foster ........................... .. 40/550 . 4,925,234 A 5/1990 Park et al. (76) Inventor: R1c¢ard0V-Haynes,Med1na,OH (US) 4,958,881 A 4 9/1990 Piros ,,,,,,,,,,,,,,,,,,,,,,,,,,,,, H 296/98 4,966,406 A * 10/1990 Karasik et al. ................ .. 296/98 ( * ) Notice: Subject to any disclaimer, the term of this 5,016,145 A 5/ 1991 Singleton patent is extended or adjusted under 35 5,076,196 A * 12/1991 Chan ......................... .. 116/28 R U_S_C_ 154(1)) by 253 days_ 5,129,678 A * 7/1992 Gurbacki .................... .. 280/770 5,158,324 A 10/1992 Flesher _ 5,398,437 A * 3/1995 Bump et al. .................. .. 40/582 (21) APP1-NO-- 12/4201129 5,424,924 A * 6/1995 Ewing etal. 362/545 _ 5,533,287 A * 7/1996 Cole ............................. .. 40/591 (22) Flled: Apr. 8, 2009 6,056,425 A 5/2000 Appelberg 6,371,547 B1 4/2002 Halbrook (65) Prior Publication Data 7,063,375 B2 6/2006 Dringenberg et al. 7,095,334 B2 8/2006 Pederson US 2010/0019479 A1 Jan. 28, 2010 7,154,383 B2 12/2006 Berquist 7,175,229 B2 2/2007 Garcia - - 7,213,870 B1 5/2007 Williams Related US. Application Data 7,233,849 B2 6/2007 Hill et a1‘ (60) Provisional application No.
    [Show full text]
  • Saab 9-3 M03- Fog Lights
    900SCdefault Installation instructions MONTERINGSANVISNING · INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG · INSTRUCTIONS DE MONTAGE SITdefault Saab 9-3 M03- Fog lights Accessories Part No. Group Date Instruction Part No. Replaces 12 787 092 9:35-05 May 03 12 789 095 12 789 095 Oct 02 F980A110 Saab 9-3 M03- 2 12 789 095 2 3 1 F930A248 1 Fog light L 2 Fog light R 3 Nuts (x4) The following part is also required (ordered separately) Light Switch Position Saab 9-3 M03- 12 789 095 3 2 2 2 2 2 2 3 2 F980A112 1 Raise the car. 2 Remove the spoiler shield, unplug the bumper connector and remove it from the holder on the spoiler shield. Cars with headlamp washers: Unhook the hose from the spoiler shield. 3 Clip the cable ties securing the connectors. Saab 9-3 M03- 4 12 789 095 4 4 5 4 6 6 4 7 F930A249 4 Remove the lower grille by bending in the locking tabs. Remove the temperature sensor from the grille. 5 Remove the covers. 6 Insert the fog light into the casing and fit the nuts. 7 Attach the connectors. Saab 9-3 M03- 12 789 095 5 9 8 8 9 9 F980A114 8 Fit the temperature sensor and the lower grille. 14 Adjust the fog lights and check their function Make sure the locking tabs fasten properly. according to car specifications. 9 Lift up the spoiler shield, fit the bumper connector Example: In Europe, as per vehicle testing into the holder and plug in the connector. requirements, fog lights may be used if the park- Cars with headlamp washers: Hook the hose ing lights, dipped or main beams have been to the spoiler shield.
    [Show full text]
  • Vespa-S150 2010-2014 (USA)
    SPARE PARTS CATALOGUE Vespa S 150 4T ie College 2009 - 2013 (USA) Chassis prefix: ZAPM688F Engine prefix: M683M Vespa S 150 EVPF000US1 Chassis prefix: ZAPM688F Vespa S 150 Engine prefix: M683M EVPF000US1 - Vespa S 150 4T ie College 2009 - 2013 (USA) Index Finished products........................................................................................................................................................................... 4 Alphanumeric index....................................................................................................................................................................... 5 Engine........................................................................................................................................................................................... 10 Table 01.02 - Engine, assembly..............................................................................................................................................10 Table 01.05 - Crankcase..........................................................................................................................................................11 Table 01.06 - Crankshaft.........................................................................................................................................................13 Table 01.07 - Cylinder-piston-wrist pin unit...........................................................................................................................14 Table 01.10 - Head unit
    [Show full text]
  • Design and Analysis of a New Rear Spoiler for Su Vehicle Mahindra Bolero Using Cfd
    International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395 -0056 Volume: 03 Issue: 06 | June-2016 www.irjet.net p-ISSN: 2395-0072 DESIGN AND ANALYSIS OF A NEW REAR SPOILER FOR SU VEHICLE MAHINDRA BOLERO USING CFD Kelbessa Kenea Deressa1, Kiran Kumar Sureddy2 1 Head of the Department, Department of Mechanical Engineering, Bulehora University, Ethiopia 2Lecturer, Department of Mechanical Engineering, Bulehora University, Ethiopia Abstract-Environmental issues and increased fuel are flowing underneath the vehicle which generally reduces driving forces for the automotive manufactures to develop aerodynamic lift and drag. Spoilers are often fitted to race and high-performance sports cars, although they have more fuel efficient vehicles with lower emissions. The need become common on passenger vehicles as well. Some for fuel efficiency is a rapidly increasing trend in spoilers are added to cars primarily for styling purposes automotive industries in the recent years. Therefore, and have either little aerodynamic benefit or even make the extensive research is undergoing for development of aerodynamics worse. Spoilers on the rear of a car are aerodynamically optimized vehicle designs. One of the known as wings when the fascia that produces the drag and design goals of the spoiler is to reduce drag and increase fuel down-force is physically separate from the body. A few years ago when oil crisis was not a problem, cars were efficiency. The drag coefficient is an important factor that mainly designed for high-speed maneuver, comfort, and determines the fuel efficiency of a vehicle in close safety. However, with the recent impact due to the proximity to the ground.
    [Show full text]
  • (56 GRE, 4-7 April 2006 Agenda Item 1.1.) PROP
    Informal document No. GRE-56-31 Transmitted by the Chairman of (56th GRE, 4-7 April 2006 the informal group agenda item 1.1.) PROPOSAL FOR A NEW GLOBAL TECHNICAL REGULATION (gtr) LIGHTING AND LIGHT-SIGNALLING DEVICES FOR ROAD VEHICLES: INSTALLATION PROVISIONS FOR VEHICLES OTHER THAN MOTORCYCLES Note: The text reproduced below was adopted by the informal group on the global technical regulation (gtr) on installation of lighting and light-signalling devices at its ninth informal meeting. After consideration at the fifty-sixth GRE session, it will be distributed with an official symbol ECE/TRANS/WP.29/GRE/2001/6/Rev.6 at GRE October 2006 session. The experts are invited to send their comments concerning this document to the Chairman of the informal group by end of May 2006 (gorzkom@tc.gc.ca). It is expected that for further development of this document the 10th informal meeting of the informal group may be organized in June 2006 (Ottawa) or a teleconference, if appropriate. page 2 DRAFT GLOBAL TECHNICAL REGULATION ON LIGHTING AND LIGHT-SIGNALLING DEVICES FOR ROAD VEHICLES: INSTALLATION PROVISIONS FOR VEHICLES OTHER THAN MOTORCYCLES TABLE OF CONTENT: 1. SCOPE AND PURPOSE 2. APPLICATION 3. DEFINITIONS 4. GENERAL SPECIFICATIONS 5. INDIVIDUAL SPECIFICATIONS 5.1. DRIVING BEAM HEADLAMP 5.2. PASSING BEAM HEADLAMP 5.3. FRONT FOG LAMP 5.4. REVERSING LAMP 5.5. DIRECTION INDICATOR LAMP AND HAZARD WARNING SIGNAL 5.6. MIDDLE-SIDE DIRECTION INDICATOR 5.7. STOP LAMP AND CENTRE STOP LAMP 5.8. REAR REGISTRATION PLATE ILLUMINATING DEVICE 5.9. FRONT POSITION LAMP 5.10. REAR POSITION LAMP 5.11.
    [Show full text]
  • Honolulu Police Department Policy Law Enforcement
    HONOLULU POLICE DEPARTMENT POLICY LAW ENFORCEMENT OPERATIO NS 1 July 29, 201s Policy Number 4.141 POLICE SUBSIDIZED VEHICLES POLICY Privately owned automobiles used for police service (subsidized vehicles) shall comply with the specifications and guidelines established herein. PROCEDURE I. APPROVED VEHICLE LISTS A. Unless otherwise approved in writing by the Chief of Police, the only authorized subsidized vehicles are those specified on the attached approved vehicle lists. Vehicles are listed by year and model. B. Officers may propose vehicles to be considered for the approved vehicle lists. 1. The proposal shall be in the form of a memorandum and submitted to the commander of the Information Technology Division (ITO). 2. The proposed vehicle shall comply with all of the standards, specifications, restrictions, etc., established in this directive. It shall also be readily available for physical inspection by the ITO at the time the proposal is submitted. I I. GENERAL SPECIFICATIONS A. Wheelbase The wheelbase shall be no less than 100 inches. B. Engine Size 1. Engines with eight cylinders shall have a maximum displacement of 400 cubic inches. PUBLIC VERSION Security procedures and information redacted pursuant to HRS Section 92F 13(3). July 29, 2015 Policy Number 4.14 Page2 2 . Engines shall have a minimum of four cylinders. C. Fuel 1. Only gasoline engines are acceptable. 2. The department dispenses only 89 octane-level gasoline for all subsidized vehicles. D. Tire Size Tires shall fit the standard rim for the vehicle, not exceed ten inches in width, and not extend beyond the width of the fenders. Rim and tire sizes shall be the same for all four wheels with the only exception being noted for a specific vehicle on the approved vehicle lists.
    [Show full text]
  • Design and Fabrication of Adaptive Spoiler for Go - Kart Vehicles
    INTERNATIONAL JOURNAL OF SCIENTIFIC & TECHNOLOGY RESEARCH VOLUME 9, ISSUE 03, MARCH 2020 ISSN 2277-8616 Design And Fabrication Of Adaptive Spoiler For Go - Kart Vehicles K.S. Karthi Vinith, P. Sathiamurthi Abstract: The vehicle accident also occurs due to over speed in the cornering, particularly in high speed cars (formula cars). The main objective of project is to replace the DRAG REDUCTION SYSTEM (DRS) in formula cars. The DRS system cost over 2 to 5 lakhs depends upon the formula Race type. On fixing of adaptive spoiler in formula cars it reduces cost and increase the performance and Drag during turning. The major source to reduce the speed of the vehicle is braking system. Another source that can be utilized to decelerate the vehicle on high speed travelling is aerodynamics. Adaptive Spoiler is one major solution for decelerating the vehicle using aerodynamics. Adaptive Spoiler serves to be efficient when compared with conventional spoiler. However, the use of adaptive spoiler with compact and cost effective design is rare in vehicles. The operation of Adaptive Spoiler is based on hydraulic motors and sensors are one of its major drawbacks and it’s not yet equipped in economic passenger cars. The use of adaptive spoiler in super cars is much costlier and does not fall in the economic category. The tilting operation will be controlled by the steering wheel using cable mechanism. The Adaptive Spoiler is pivoted at the center, using a C-clamp. When the steering wheel rotates, the 2 cables attached at both ends of the steering column will push and pull the cables at specific ends in order to tilt the spoiler.
    [Show full text]
  • Effect of Spoiler Design on Hatchback Car
    EFFECT OF SPOILER DESIGN ON HATCHBACK CAR Ashpak Kazi1*, Pradyumna Acharya2, Akhil Patil3 and Aniket Noraje4 1,2,3,4 Department of Automotive Engineering, School of Mechanical Engineering, VIT University, Vellore, Tamil Nadu, India, 632014 Abstract- The aerodynamic aspects of automobiles have received more interest recently. Detailed knowledge of vehicle aerodynamics is more important to improve fuel efficiency and enhance stability of vehicle at high speed cruising. Additionally it provides improved external aesthetics. There are different ways to improve the aerodynamic performance of a car like using spoilers, air dam, diffuser etc. This paper deals with effect of addition of spoiler on Volkswagen Polo car in terms of coefficient of drag and lift. Main purpose of spoiler is to generate down force or negative lift. More down force is good but at the same time drag produced must be minimum. It is more important to maximize the down force to drag ratio. The VW Polo car was analyzed for two cases namely with and without spoiler. Creo 2.0 was used for modeling and Ansys Fluent 15 was used for CFD analysis. Validation was done with ahmed body. k-ω shear stress transport turbulence model was used for simulation. The results showed the effect of introduction of rear spoiler on drag and lift. Keywords- Spoiler, k-ω turbulence model, polyhedral mesh, Ansys fluent 15, Creo 2.0 *Corresponding Author : Ashpak Kazi I. INTRODUCTION When vehicle is running at speeds greater than 100 kmph it leads to uncontrollable lift and pitching moments hence high drag is produced. Lift is generated due to high velocity low pressure air flowing at the top of the vehicle and low velocity high pressure air flowing at bottom of the vehicle.
    [Show full text]
  • CAL ZN-5144-Supplement.Pdf
    0 .. Novemb2r ~ 7, 1972 Cornell AerO'1autjc.Ji Laboratory (CAL) changed jts name to Caj~pan CorporatIon and converted to for-profit OCe~,1t10r,::; C<'l:s.pan is dedlcat€!d r0 carrvlng on CAL's tor.g-~~andin') tradition of advanced research and development tron) arl i"rJeD~nd.sn{ \"t.::;,,, .. point_ All Dt CA L's civerse scienTific and enq;neering progralT1s for governrTlent af1rj ,ndustrv are beIng :Or)tlr'LJe'J '.' "'-I~: _~~,..':;<"" e~-":t'5, '::1f'CtrO~.!;'S arlO aVlon:;:s. ~omputer SClef"'Ges, "transportatio'l ann 'J":!!lic!e research, ar~d the environ­ mental SCi~"CI?~, C:-lI'.~r'Mr) It.; composeCI of the same staff, management. and facilities as CAL.- which operated $ince 1946 undl:!r fe,jeral !ncur~12 tax ~>":8mption. A Supplement To AN EVALUA TlON OF THE SAFETY PERFORMANCE OF TRICYCLES AND MINIBIKES Prepared For: DEPARTMENT OF HEALTH, EDUCATION AND WELFARE FOOD AND DRUG ADMINISTRATION BUREAU OF PRODUCT SAFETY ROCKVILLE, :\1ARYLAND 20852 NOVEMBER 1972 CONTRAC1 NO. FDA 72·91 PREPARED BY: ~~'.'~ APPROVED BY: R.S. Rice, Hec.i K.D. Bird, Head Vehicfe Dynamics Section Vel1Jcle Research Department /(, tYt~~&J ~ f R.D. Roland Research Engineer FOREWORD This docum ent is a supplementary volum e to the principal tech­ nical report, An Evaluation of the Safety Performance of Tricycles and Mini­ bikes, Calspan Report No. ZN-5l44-K-l on the work performed under Contract No. FD.:-\ 72-91 for the Bureau of Product Safety, Food and Drug Administration. Most of the observations and evaluations given herein were made by the test rider, Mr.
    [Show full text]
  • MY20 Panigale V2 DEF ENG.Pdf
    Panigale V2 | 3 Index 5 Panigale V2: Red Essence 16 First-class technology and electronics 6 Perfect balance of power and elegance 21 Riding Modes: each to their own riding style 10 Ducati Superquadro: efficient on track, smooth 22 Servicing and maintenance and enjoyable on the road 25 Technical data and equipment 13 The integration of a multifunctional frame 30 Accessories 14 Chassis: top quality components 36 Apparel 5 | Panigale V2 Panigale V2: Red Essence The Panigale twin has been given Equipment also includes a new a thorough makeover. Renamed electronics package that incorporates the Panigale V2, it adopts a totally ABS “Cornering” in addition to the new design, features sophisticated Quickshift (now with downshift function), electronics based on a 6-axis IMU and, engine brake traction control and anti- thanks to a more comfortable rider seat wheelie function. These controls are and updated suspension set-up, offers integrated into the Riding Modes (Race, better yet safer sports performance Sport and Street) and can be managed while making road riding more enjoyable via the new 4.3” colour TFT display that and user-friendly than ever. ensures more intuitive menu navigation, settings adjustment and Riding Mode The name tells Ducati twin-cylinder identification. enthusiasts that the bike is powered by the 955 cc Superquadro. Key features of the new Panigale V2 Include the single- sided swingarm and new exhaust with under-engine silencer, compact and with a single lateral exit, which stand out at first glance. A muscular yet elegant new design envelops the mechanics and emphasises the compact dimensions of the twin.
    [Show full text]