Masterpav PU Top Coat PU610 Technical Data Sheet
Total Page:16
File Type:pdf, Size:1020Kb
Masterpav PU Top Coat PU610 Technical Data Sheet DESCRIPTION Masterpav PU Top Coat PU610 is a two-component aliphatic polyester polyurethane coating. This polyurethane top coat provides outstanding gloss retention and superior hardness with abrasion and durability. This system has excellent UV resistant with non- yellowing performance. It is recommended as a finish coating for interior and exterior application of Masterpav Zenstone Resin finishing and any type of concrete floor RECOMMENDED APPLICATION Ideal as a topcoat for any decorative flooring such as Masterpav Zenstone Resin system and Masterpav Polymer Resurfacing. Masterpav PU610 is also suitable for metal, concrete and timber surfaces TECHNICAL INFORMATION Appearance Clear Liquid Finish Clear Liquid Solid (PBW)(%) 38 ± 2 No. of component 2 Mixing Ratio (by part of volume) Part A : Part B/ 4:1 Pot Life @ 25°C Overnight Dry Time @ 25°C Set Touch : 45 min Dry to Recoat : 18 hours Dry to foot traffic : 24- 36 hours Dry to Vehicle Traffic : 4-7 days COVERAGE RATES 7 – 8 m2/L depends on substrate porosity and texture, and application method. Excessive build up should be avoided. TYPICAL CHEMICAL RESISTANCE Exposure Splash & Spillage Fumes Acids Good Good Alkali Good Good Solvent Good Good Salt Water Excellent Excellent Water Excellent Excellent PACKAGING Available in 1L & 5L All statements and recommendations are based on experience we believe to be reliable. The use or application of these products being beyond the control of the seller or manufacturer, neither the seller nor the manufacturer make any warranty expressed or implied, as to results or hazard from its use. The suitability, risk and liability whatso ever of a product for any intended use shall be solely up to the user Master Materials Manufacturing Sdn Bhd (203747-T) Lot 1826, Jalan KPB1, Kawasan Perindustrian Kg.Baru Balakong 43300 Seri Kembangan, Selangor Darul Ehsan, Malaysia Tel: 603-8961 3798/ 8961 1933 Fax: 603-8962 2449/ 8961 3385 Email: [email protected] Website: www.mastermaterials.com Masterpav PU Top Coat PU610 Technical Data Sheet INSTRUCTION FOR USE SURFACE PREPARATION: The surface to be coated must be thoroughly cleaned and degreased to ensure that oil, grease and others surface contaminants are removed. The surface preparation method could be vary for different types of surfaces, to ensure right method, consult the manufacturer for more details MIXING: Stir Part A content thoroughly, then add the entire content of Part B into Part A container and stir until homogenous APPLICATION: Masterpav PU610 can be applied by brush, roller or spray equipment. Ensure that sufficient material is applied evenly to the entire surfaces. For application in enclosed area, provide sufficient ventilation to ensure proper drying of applied materials. CURING: The rate of curing is dependent on environment conditions and surrounding temperature. Provide good ventilation during and after application to ensure proper and speed curing. STORAGE & SHELF LIFE Stored in cool and dry area, away from heat sources, flammable areas. Containers should be sealed and tightly closed and sealed upright. Masterpav PU Top Coat PU610 has a shelf life of up to 1 years in it's original, sealed, unopened container from the date of production. SAFETY/ FIRST AID Flammable and Harmful. Store away from heat sources. Container should be tightly closed and sealed. It is advisable to wear a mask during applications. In case of eye contact, rinse immediately with plenty of water and seek for medical advice. All statements and recommendations are based on experience we believe to be reliable. The use or application of these products being beyond the control of the seller or manufacturer, neither the seller nor the manufacturer make any warranty expressed or implied, as to results or hazard from its use. The suitability, risk and liability whatso ever of a product for any intended use shall be solely up to the user Master Materials Manufacturing Sdn Bhd (203747-T) Lot 1826, Jalan KPB1, Kawasan Perindustrian Kg.Baru Balakong 43300 Seri Kembangan, Selangor Darul Ehsan, Malaysia Tel: 603-8961 3798/ 8961 1933 Fax: 603-8962 2449/ 8961 3385 Email: [email protected] Website: www.mastermaterials.com .