Great Smoky Mountain Bladesmith Symposium March 17-20, 2016

Total Page:16

File Type:pdf, Size:1020Kb

Great Smoky Mountain Bladesmith Symposium March 17-20, 2016 GREAT SMOKY MOUNTAIN BLADESMITH SYMPOSIUM MARCH 17-20, 2016 Offered by the American Bladesmith Society, Inc. & Hosted by Haywood Community College On the campus of Haywood Community College – 185 Freelander Drive, Clyde, NC Bring examples of your work for the knife show. Knife Show tables are free to paid attendees. Knife Show, Battle of Bladesmith and Auction are open free to General Public --Registered Tail Gate Sales & Suppliers are welcome-- PLEASE VISIT THE VENDORS AND SUPPORT THEM Thursday, March 17, 2016 4-6 pm Demo Area Check in and registration 6:30 pm Sagebrush of Waynesville, 895 Russ Demonstrators dinner Avenue, Waynesville, NC, 28786 Everyone welcome to meet the Demonstrators Phone: 828-452-5822 Friday, March 18, 2016 8-10 am DEMO AREA Jason Knight – Forging a Blade to Cutting Edge CLASSROOM Steve Dunn – Damascus Design FORGE AREA GREEN COAL – hands on – 10-12 am DEMO AREA Steve Dunn – Damascus Making CLASS ROOM Greg Neely – Judging Standards FORGE AREA GREEN COAL – hands on – 12-1 pm Lunch Break 1-3 pm DEMO AREA Steve Dunn – Damascus Making CLASSROOM Steven Rapp – Silver Sheaths FORGE AREA GREEN COAL – hands on – 3-5 pm DEMO AREA Jason Knight – Blade Grinding CLASSROOM Klingspor – Selecting the right belts and papers for the task at hand FORGE AREA GREEN COAL – hands on – Charlie Ellis Saturday, March 19, 2016 8-10 am DEMO AREA Greg Neely – Heat Treating CLASSROOM Burt Foster – Kydex Sheaths FORGE AREA GREEN COAL – hands on – Charlie Ellis 10-12 am DEMO AREA Steven Rapp – Blade Finishing CLASS ROOM Chris Williams – Forge Construction FORGE AREA GREEN COAL – hands on – Saturday, March 19, 2016 12-1 pm Lunch break Knife Show, Battle of Bladesmith and Auction are open free to General Public 1-2:30 pm CLASSROOM Knife Makers Show 2:30-5 pm DEMO AREA Battle of the Bladesmith – Competition Steve Dunn Burt Foster Jason Knight Steve Randell 5-6 pm DEMO AREA AUCTION open to the public General Public is welcome to the BBQ Dinner but advance reservations are recommended. Contact Ken Hall at 828-400-7815. 6 pm DINNER BBQ Dinner (Additional cost to attend) Sunday, March 20, 2016 9-11 am DEMO AREA David Burnett – Forging Tongs CLASS ROOM Ken Hall – What to consider in pricing a knife. FORGE AREA ----closed--- 11-12 am DEMO AREA ROUND TABLE WITH ALL DEMONSTRATORS QUESTION AND ANSWER SESSION REGISTRATION FORM GREAT SMOKY MOUNTAIN BLADESMITH SYMPOSIUM MARCH 17-20, 2016 First name: _________________________ Last name: _________________________________ Address: ____________________________________________________________________ City: _________________________________State: _______________ Zip: _______________ Phone: _______________________________Email: __________________________________ How many attending the demonstrator dinner Friday night: _______ Registration Fees - $75 Registration Information Register early and avoid the paperwork at the registration table. By Mail Make check or money order payable to American Bladesmith Society, Inc. and mail to: American Bladesmith Society, P.O. Box 160, Grand Rapids, OH 43522 Online Register online through the ABS Website Store by credit card. www.americanbladesmith.com look for the Store link Registration Questions – Call or text Ken Hall at 828-400-7815. Directions to Haywood Community College, HCC -From Ashville, take I-40 West, Exit 27 onto US 19/US23, take Exit 107 onto East Jones Cove Rd, and follow HCC signs -From Sylva, NC, take US23/US74 East, Exit 105 onto Jones Cove Rd, turn left, turn right at next stop sign, HCC is on left Accommodations -Lake Junaluska Conference and Retreat Center, 800-222-4930, 91 N Lakeshore Dr, Lake Junaluska, NC 28745 http://www.lakejunaluska.com (Check on line, in January they rooms for around $60 per night) -Lodge of Waynesville, 828/452-0353, 909 Russ Ave (US276), take exit 102 off US74/US23 -Days Inn, 828/452-9009, 232 Phillips Rd, take exit 102 South off US74/US23 -Super 8 Motel, 828/454-9667, 79 Liner Cove Rd, take exit 104 off US23/US74 -Best Western, 828/456-4402, 130 Shiloh Trail, take exit 98 North off US23/US74 .
Recommended publications
  • Damascus Steel
    Damascus steel For Damascus Twist barrels, see Skelp. For the album of blades, and research now shows that carbon nanotubes the same name, see Damascus Steel (album). can be derived from plant fibers,[8] suggesting how the Damascus steel was a type of steel used in Middle East- nanotubes were formed in the steel. Some experts expect to discover such nanotubes in more relics as they are an- alyzed more closely.[6] The origin of the term Damascus steel is somewhat un- certain; it may either refer to swords made or sold in Damascus directly, or it may just refer to the aspect of the typical patterns, by comparison with Damask fabrics (which are in turn named after Damascus).[9][10] 1 History Close-up of an 18th-century Iranian forged Damascus steel sword ern swordmaking. These swords are characterized by dis- tinctive patterns of banding and mottling reminiscent of flowing water. Such blades were reputed to be tough, re- sistant to shattering and capable of being honed to a sharp, resilient edge.[1] Damascus steel was originally made from wootz steel, a steel developed in South India before the Common Era. The original method of producing Damascus steel is not known. Because of differences in raw materials and man- ufacturing techniques, modern attempts to duplicate the metal have not been entirely successful. Despite this, several individuals in modern times have claimed that they have rediscovered the methods by which the original Damascus steel was produced.[2][3] The reputation and history of Damascus steel has given rise to many legends, such as the ability to cut through a rifle barrel or to cut a hair falling across the blade,.[4] A research team in Germany published a report in 2006 re- vealing nanowires and carbon nanotubes in a blade forged A bladesmith from Damascus, ca.
    [Show full text]
  • Knife World Books
    SPRING 2019, Issue 55 ® JOURNAL OF THE AMERICAN BLADESMITH SOCIETY, INC. Officers Board of Directors In This Issue Editor’s Note Harvey Dean (04) Robert Calvert (07) 4 Chairman 911 Julia Street 5 ABS Calendar 3266 CR 232 Rayville, LA 71269 5 School Calendars Rockdale,TX 76567-4302 318-348-4490 6 Chairman’s Corner 512-446-3111, [email protected] 8 Annual Meeting Schedule [email protected] 9 Auction Knife Descriptions Kevin R. Cashen (11) 10 Mid America Symposium Info Steve Dunn (03) 5615 Tyler Street 11 New England Symposium Flyer Vice Chairman Hubbardston, Michigan 48845-9708 376 Bigger Staff Road 989-981-6780 13 Art of Steel Show Awards Smiths Grove, KY 42171 [email protected] 18 Great Smoky Mountain Hammer-in 270-563-9830, 21 Alabama Forge Council [email protected] Mark Zalesky (11) 26 AD Index 4152 Forest Glen Drive Billy Ray Hughes (76) Knoxville, TN 37919 Carolyn Hughes, Editor Secretary & Founder 865-540-4189 305 Phillips Circle [email protected] American Bladesmith is published 3 times a year Wake Village, TX 75501 by the American Bladesmith Society, PO Box 903-838-0134, James Rodebaugh (15) 160, Grand Rapids, OH 43522 and is printed [email protected] P.O. Box 404 by NeTex Printing, 3101 New Boston Rd., Carpenter, WY 82054 Texarkana, TX 75501. The publishers and staff of Bill Wiggins (09) 307-649-2394 American Bladesmith are not responsible for any Treasurer [email protected] mishaps which might occur from use of published 105 Kaolin Lane information. No part of the publication may be Canton, NC 28716 Robert Wilson (18) reproduced without written permission from the 828-226-2551 3659 Battle Road editor.
    [Show full text]
  • Knives 2019 Amoureux—Armour
    custom knifemakers ABEGG—AMOS Uses stainless, salvage wrought iron, brass and copper for fi ttings. Handle materials A include stabilized and natural domestic and exotic fi gured woods, durable synthetics, ABEGG, ARNIE stacked leather. Makes own sheaths. Prices: $300 and up. Remarks: Part-time maker. 5992 Kenwick Cr, Huntington Beach, CA 92648, Phone: 714-848-5697 First knife sold in 2013. Doing business as Aldrich Knife & Tool. Emphasis put on clean ABERNATHY, LANCE lines, fi t and fi nish and performance. Mark: An arched ALDRICH. Sniper Bladeworks, 1924 Linn Ave., North Kansas City, MO 64116, Phone: 816-585- ALEXANDER, EUGENE 1595, [email protected]; Web: www.sniperbladeworks.com Box 540, Ganado, TX 77962-0540, Phone: 512-771-3727 Specialties: Tactical frame-lock and locking-liner folding knives. Alexander,, Oleg, and Cossack Blades ACCAWI, FUAD 15460 Stapleton Way, Wellington, FL 33414, Phone: 443-676-6111, Web: www. 130 Timbercrest Dr., Oak Ridge, TN 37830, Phone: 865-414-4836, gaccawi@ cossackblades.com comcast.net; Web: www.acremetalworks.com Technical: All knives are made from hand-forged Damascus (3-4 types of steel are used to Specialties: I create one of a kind pieces from small working knives to performance create the Damascus) and have a HRC of 60-62. Handle materials are all natural, including blades and swords. Patterns: Styles include, and not limited to hunters, Bowies, daggers, various types of wood, horn, bone and leather. Embellishments include the use of precious swords, folders and camp knives. Technical: I forge primarily 5160, produces own metals and stones, including gold, silver, diamonds, rubies, sapphires and other unique Damascus and does own heat treating.
    [Show full text]
  • News-LEADER Arkansas’S Heritage While Leading Through the 21St Century Wednesday, Jan
    THE NASHVILLE HH HH Preserving SouthwestNews-LEADER Arkansas’s Heritage While Leading Through the 21st Century Wednesday, Jan. 15, 2020 u Vol. 17, Issue 29 u 14 pages, 2 sections u 75¢ Leader Governor to dedicate Board ‘Arkansas #1’ Friday www.swarkansasnews.com at Historic Washington OPINION 4A Knife designed by local bladesmith Prince may be HISTORIC WASHINGTON - statehood. The twelve-inch blade competitor for Gov. Asa Hutchinson will be the also contains steel from the hand- post of local guest speaker at the grand open- rail of the Statue of Liberty to ing of the James Black School of represent the liberty and freedom j-turn officer. Bladesmithing and Historic Trades Arkansans enjoy as American citi- Friday, Jan. 17, at 2:30 p.m. at His- zens. Twenty-five arrow points are toric Washington State Park. in the running wheat pattern start- Hempstead The school is located in the ing from the center of the back of Stephens House at 601 Lawrence the handle to the guard. The points County sets St. in Washington. It is part of the signify Arkansas being designated University of Arkansas Hope- as the 25th state to join the union, info meetings Texarkana. and each point also represents a Hutchinson will formally dedi- star on the flag of Arkansas. on sales tax cate the “Arkansas #1” Bowie The handle of Arkansas #1 is A series of meetings knife. Arkansas #1 was commis- fashioned from the state-designat- will be held throughout sioned by the UAHT Foundation ed James Black Walnut Tree located Hempstead County over to commemorate the significance in the cemetery where James Black the next few weeks as of the Bowie knife being named Ar- is buried.
    [Show full text]
  • The State of The
    swords.qxd 7/14/04 9:33 PM Page 1 SWORDSMITHING In ancient times, the sword represented the THE STATE pinnacle of the OF THE engineering craft. Today, many of the same ART technologies are used to produce swords for a variety of purposes. Byron J. Skillings* Ladish Co., Inc. Cudahy, Wisconsin ince early times, the search for superior arms and armor has driven the art and the science of metallurgy. European, Middle- Eastern, and Eastern cultures each devel- Fig. 2 — The rapier was not considered a Soped metallurgical and bladesmithing technolo- military weapon, but rather served as a per- gies suitable for their swords, for personal defense sonal side arm for self-defense and for settling and military weapons. Swords were symbols as duels. This rapier is by Kevin Cashen, Math- erton Forge. well as weapons, used to show positions in gov- ernment, social status, and wealth. The sword, ar- guably more than any other of man’s tools, speaks of our innate drive to create items of form as well as function. They were for many eons the pinnacle of the engineering craft. Without scientific knowl- edge and analytical equipment, ancient smiths were able to convert impure contaminated raw ore into refined metal. From this material they consistently produced the lightest, strongest, most resilient tools Fig. 3 — Medieval sword by Randal suited for a purpose where failure meant death. Graham has a simpler hilt than the This was an incredible achievement. rapier. This is an example of an in- terpretation of a historical sword, not a duplication. Image courtesy Early swords Albion Armorers.
    [Show full text]
  • Experiments on Knife Sharpening
    Experiments on Knife Sharpening John D. Verhoeven Emeritus Professor Department of Materials Science and Engineering Iowa State University Ames, IA September 2004 page 2 [1] Introduction page 8 [2] Experiments with Tru Hone knife sharpening machine page 12 [3] Experiments with steels page 18 [4] Hand Sharpening with flat stones and leather strops page 25 [5] Experiments with the Tormek machine page 32 [6] Buffing wheel experiments page 37 [7] Experiments with carbon steels page 40 [8] Experiments with diamond polishing compound page 43 [9] Summary and Conclusions page 46 References page 47 Appendix 1 Edge angle measurements with a laser pointer page 48 Appendix 2 The Tormek sharpening machine page 53 Appendix 3 The Tru Hone sharpening machine Note: This work was supported by the Departments of Materials Science and Engineering and Mechanical Engineering at ISU by providing the author with laboratory space, machine shop service and use of the scanning electron microscope. [1] Introduction This report presents the results of a series of tests done on various aspects of knife sharpening. It is divided into sections devoted to each aspect. Each section terminates with a set of conclusions and a Summary of these conclusions is presented at the end of the report. This work has concentrated on evaluating the effectiveness of various knife sharpening techniques by examining the sharpened edges of the knives in a scanning electron microscope, SEM. Much can be learned by examination of a sharpened knife edge with a magnifying glass or an optical microscope, particularly the binocular microscope. However, the optical microscope suffers from a severe limitation.
    [Show full text]
  • Confidence in Hand® Contents
    CONFIDENCE IN HAND® CONTENTS DEADBOLT .....................................................................................................................® 3-4 KINEMATIC ™....................................................................................................................5-6 RUGER ............................................................................................................................7 FORGED BY WAR ®..........................................................................................................8 INNOVATIONS & TECHNOLOGY ..................................................................................9 SAFETY & ACTUATION .................................................................................................10 DESIGNERS ...................................................................................................................11-16 NEW PRODUCTS .................................................................................................17-35 DEALER WORKBOOK ...................................................................................................36 EVERYDAY CARRY ...............................................................................................36-70 HUNT & FISH .......................................................................................................71-73 OUTDOOR .............................................................................................................74-79 SURVIVAL .............................................................................................................80-82
    [Show full text]
  • The Gods & the Forge
    ificah International Foundation of Indonesian Culture and Asian Heritage The Gods & the Forge Balinese Ceremonial Blades The Gods & the Forge in a Cultural Context This publication is the companion volume for the exhibition of the same name at the IFICAH Museum of Asian Culture in Hollenstedt-Wohlesbostel, Germany December 2015 to October 2016. Title number IFICAH V01E © IFICAH, International Foundation of Indonesian Culture and Asian Heritage Text: Dr. Achim Weihrauch, Efringen-Kirchen, Germany Dr. Udo Kloubert, Erkrath, Germany Adni Aljunied, Singapore Photography: Günther Heckmann, Hollenstedt, Germany Printing: Digital Repro Druck GmbH, Ostfildern, Germany Layout: S&K Kommunikation, Osnabrück, Germany Editing: Kerstin Thierschmidt, Düsseldorf, Germany Image editing: Concept 33, Ostfildern, Germany Exhibition design: IFICAH Display cases: Glaserei Ahlgrim, Zeven, Germany "Tradition is not holding onto the ashes, Metallbau Stamer, Grauen, Germany Conservation care: but the passing on of the flame." Daniela Heckmann, Hollenstedt, Germany Thomas Moore (1477–1535) Translation: Comlogos, Fellbach, Germany 04 05 Foreword Summer 2015. Ketut, a native of Bali, picks me Years earlier, the fishermen had sold the land up on an ancient motorcycle. With our feet bordering the beach to Western estate agents, clad in nothing more resilient than sandals, we which meant however that they can now no ride along streets barely worthy of the name longer access the sea with their boats ... to the hinterland. We meet people from dif- ferent generations who live in impoverished It is precisely these experiences that underline conditions by western standards and who wel- the urgency of the work carried out by IFICAH – come the "giants from the West" with typi- International Foundation of Indonesian Culture cal Balinese warmth.
    [Show full text]
  • 101 Knife Designs: Practical Knives for Daily
    101 KNIFE DESIGNS PRACTICAL KNIVES FOR DAILY USE MURRAY CARTER TABLE OF CONTENTS Cover Title Page Disclaimer Terms and Definitions Introduction Part 1: Design Theory, Practical Designs For Daily Use Culinary Blades • Paring Knives • Slicing knives • Chopping Knives AKA Cleavers Knives for Work, Hobbies and Outdoors • Utility Knives, blades 4 inches and less • Combat Knives, 7 to 9 inch blades • Camp Knives, 10-12 inch blades • Machetes, 16-20 inch blades • Swords, blades over 20 inches Classic Knife Designs Part 2: How To Create And Preserve New Designs How to Grow Your Pattern Collection How to Modify a Pattern to Improve it Specific Features Of Blades • Point location and sharpness • Straight vs curved vs recurve edges • Blade spine/ handle junction • Handle shape, contour, and angle relative to the blade • Low drag, easily maintained profile • Sharp pommels • The 89 degree subtlety In Conclusion How To Use The Patterns Knife Patterns/Templates • Kitchen Knives • Daggers • Neck Knives • Other Knives Bibliography About the Author Acknowledgements Copyright DISCLAIMER This book is all about practical knife designs. It is written for the reader who desires first and foremost to make or own a knife that will be held and used for extended periods of time to cut things. This doesn’t mean to imply that other types of blades and knives, such as Fantasy or Art knives, have no merit in the cutlery world. Definitely not! Fantasy and Art knives offer richness and variety to the cutlery market, for everyone’s benefit. As these knives are limited only by the artist’s imagination and skills, it is exciting to see what will come along next in this exciting arena of knife design.
    [Show full text]
  • JB Prince Equipment Catalog
    CUTLERYCUTLERY wUsTHof Made in Solingen, germany CLassiC foRGEd kniVEs classic knife blades are high carbon, no-stain steel. They are a specially alloyed precision metal composed of carbon, chromium, molybdenum, and vanadium. full-tang blades are faultlessly joined to a two-piece plastic handle with the look and feel of traditional wood. a d e b f c g a. CHEf’s kniVEs b. ExTRa widE CHEf’s kniVEs d.fLExibLE HoLLow GRoUnd sLiCER g. PoinTEd sLiCERs bLadE 8" blade 10" blade 12" blade. bLadE w400 8 8" blade w401 8 w401 10 w406 13 w405 8 8" blade w400 9 9" blade e. PoinTEd sERRaTEd sLiCER w405 10 10" blade c.HoLLow GRoUnd CHEf’s knifE w400 10 10" blade 10" blade. w405 12 12" blade 8" blade. w400 12 12" blade w412 w515 f. PoinTEd HoLLow GRoUnd sLiCER 9" blade. w423 sERRaTEd bREad knifE HoLLow GRoUnd nakiRi VEGETabLE knifE 10" blade. 7" blade. w413 w521 h HoLLow GRoUnd sanTokU-sTYLE knifE 6.5" blade. i w420 fLExibLE fiLLETinG kniVEs h. 7" blade i. 8" narrow blade w411 7 w410 8 boninG knifE-sTiff 5" blade. w408 PaRinG kniVEs 3.5" blade. 4" blade. wUsTHof 5 PiECE “CLassiC” w402 3.5 w402 4 kniVEs CUTLERY sET • 8" forged chef’s knife. • 9" forged slicer. • 8" bread knife. • 4" Paring knife. • 9" Magnetized round steel. TURninG knifE w501 2.75" blade. w404 eMail: [email protected] • webSiTe: www.jbPrince.coM 101 CUTLERY wUsTHof GRand PRix ii sERiEs These blades are high carbon, no-stain steel. They are a specially alloyed precision metal composed of carbon, chromium, molybdenum, and vanadium joined to a one piece polypropylene handle with wusthof’s unique balancing weight.
    [Show full text]
  • CAS Hanwei 25Th Anniversary Catalog!
    CAS25th Anniversary Hanwei Catalog Welcome to the CAS Hanwei 25th Anniversary Catalog! 2010 marks the 25th anniversary of CAS’s inception and to celebrate our quarter-century Hanwei has excelled in producing the Silver Anniversary Shinto, a superlative Limited Edition (very limited!) version of the first Katana that Hanwei ever made for CAS. The original Shinto enabled many sword enthusiasts to afford a purpose-built cutting sword for the first time, introducing many enthusiasts to the sport of Tameshigiri, and the Silver Anniversary Shinto, featured on the covers and Page 14 of this catalog remains true to the basic design but features silver-plated fittings, advanced blade metallurgy and a stand unique to this sword. Also new to this catalog are the swords of two traditionally warring Ninja clans (the Kouga and Iga, Page 38) that depart from the typical plain-Jane Ninja styling and will be welcomed by Ninjaphiles every- where. The new Tactical Wak (Page 37) is a modern version of the traditional Wakizashi, intended for serious outdoor use and protection – it will see a lot of use in the backwoods. Reenactors will be excited about the new Hand-and-a-Half sword (the Practical Bastard Sword, Page 71), with its upgraded steel, great handling and new user-friendly scabbard styling. The number of martial arts practitioners enjoying cutting with Chinese-style swords is growing very rapidly and so we had Scott Rodell, author and teacher of this discipline, design the first purpose-built cutting sword (the Cutting Jian, Page 50) for these enthusiasts. Several mid-2009 introductions are now also included in our full catalog for the first time.
    [Show full text]
  • Bladesmithing with Murray Carter: Modern Application of Traditional Techniques Pdf
    FREE BLADESMITHING WITH MURRAY CARTER: MODERN APPLICATION OF TRADITIONAL TECHNIQUES PDF Murray Carter | 160 pages | 20 Oct 2011 | F&W Publications Inc | 9781440218385 | English | Ohio, United States Bladesmithing with Murray Carter: Modern Application of Traditional Techniques – GunDigest Store Bladesmithing with Murray Carter provides the reader with an in-depth look into traditional Japanese Cutlery forging techniques and their modern applications. A non-stop flow of inquiries to Murray has prompted him to reveal the secret techniques learned during 18 years in Japan, where he lived and worked as a village bladesmith. He now shares this wealth of information for the benefit of the curious reader and Japanese knife enthusiast alike. Owners of Bladesmithing with Murray Carter: Modern Application of Traditional Techniques 15, of Murray's knives will be delighted to see a comprehensive book written by the knives' creator. Unique and extremely rare insight into the Japanese culture through the blue eyes of a Japanese village bladesmith. Detailed explanations of Traditional Japanese Bladesmithing techniques that until now have been cloaked in mystery and myth. Enough detailed information to guide an aspiring bladesmith to become a successful smith in the Japanese style of blade making. Previous page. Larrin Thomas. Jim Bladesmithing with Murray Carter: Modern Application of Traditional Techniques. Murray Carter. A Modern Guide to Knifemaking: Step-by-step instruction for forging your own knife from expert bladesmiths, including making your own handle, sheath and sharpening. How to Make Money Making Knives. The Backyard Blacksmith. Lorelei Sims. Next page. Carter lives in Vernonia, Oregon. It is so well laid out from the start a step by step prgress in metal, smithing, handle making and finishing.
    [Show full text]