Gottfried Silbermann
Total Page:16
File Type:pdf, Size:1020Kb
HAUPTWERK USER GUIDE GOTTFRIED SILBERMANN St. Georgenkirche milandigitalaudio.com © Copyright 2020 Milan Digital Audio. All Rights Reserved. Silbermann St. Georgenkirche User Guide Installation - The Gottfried Silbermann St. Georgenkirche organ for Hauptwerk 2 was created to give organists the utmost realism in performing on this fantastic historic instrument located in Rötha, Germany not too far from the major city of Leipzig. On the DVD-Rom you will find the files needed to install this sample library to your computer. You will need to treat the organ definition file, sample files and temperament files as 3 separate installations. To install this sample library open Hauptwerk 2 then click File | Install organ, sample set, temperament, or impulse response. Navigate to your DVD-Rom drive then find the folders - files | installation_ files. You will find the files here called Silbermann-St-Georgenkirche-Samples.CompPkg.Hauptwerk, and Silbermann-St-Georgenkirche-OrganDefinitionFile.CompPkg.Hauptwerk. Users will also find a third file on the DVD-Rom called Silbermann-St- Georgenkirche-Temperaments.CompPkg.Hauptwerk which contains several temperament files for use with the organs tuning one semi-tone higher than A=440. Use the Hauptwerk installer to install each of these three files separately. Note that the sample files will take much longer to install due to the large file sizes. Due to this please allow your computer to run uninterrupted as it may take up to 10 minutes to complete the installation. Loading the Organ - Once all of the files have been installed you are now ready to load the organ into Hauptwerk 2. Due to the sample sets encryption you must have your Hauptwerk 2 dongle installed (USB key) with a valid license for this sample set for the organ to load. To load the organ open Hauptwerk 2 and choose Organ|Load organ from the drop down menu. Click on the file named StGeorgenkirche_Silbermann then click OK. The Rank Audio Output Routing screen will now appear allowing you to choose the options for loading the samples. All sample files are in 24 bit 48kHz however they may be loaded in 16 bit 48kHz to save memory requirements. Hauptwerk defaults all settings to 16 bit. The sample files also contain multiple loops allowing for more movement of the pipes sound, some samples contain up to 9 loops and are up to 8 seconds in length with another 2-3 seconds for releases. If you are running a computer with 2GB of RAM you may wish the load the samples in 16 bit with multiple loops to fit the entire organ into memory. For those with more memory (4GB or more) you may load the entire set in 16 or 32 bit with all loops enabled. You may also wish to combine compressed samples with non-compressed samples to fit the organ into a desired amount of memory. Once you have chosen the desired settings for each rank of samples click OK and the organ will begin to load. Note that the first time you load the organ it will take slightly longer due to the files being saved into a special format which enables subsequent loads to become much faster. After the organ has finished loading you will see the console display appear and you are ready to begin performing on this virtual instrument. Please consult your Hauptwerk 2 User Manual for more information on setting up stop controls and mapping your MIDI keyboards to the appropriate organ controls of this organ. Most organ controls contain default settings to get you started however certain controls may need to be set up manually with special mappings. Silbermann St. Georgenkirche User Guide Virtual Console - The virtual console is a photo-realistic replica of the original organ. Now you may experience the magnificent sound of the organ, as well as the visual and physical aspect of the organ. The organ defaults to display page 2 (Stop Controls) which has larger controls for use with computer touch screen monitors, or mouse clicks. Display page 1 (Console) contains the original organ console with all controls which are found on the original organ. Stops- The Console display page features animated 3D stop knobs which pull out or push in to add or remove a stop. Note that the stop is engaged at the moment of activation, not at the end of the stops travel. Thus you may begin playing with the newly added stop even if the stop knob is still moving to its out position. Likewise for removing a stop from the registration. All stop controls are linked from the Console display page to the Stop Controls display page and vice versa. Thus you may use either display page as your preference. Couplers- The organ includes two couplers. The first is the Oberwerk to Hauptwerk manual coupler which is a mechanical linkage between manuals. This means that when the coupler is engaged all Oberwerk keys will be activated from the Hauptwerk keys and you will see both move together. On the Console display page you may click on the Oberwerk manual key cheeks to activate the coupler which simulates the shove coupler found on the real organ (the top manual must be pushed forward to engage the coupler.) Or you choose to click the "Manaul Coppel" knob found on the Stop Controls display page. The second coupler is the Hauptwerk to Pedal coupler which is found on the Console display at the lower right center of the right stop jamb. This is also a mechanical linkage so when a pedal key is depressed it will engage the corresponding Hauptwerk key to move thus playing the stops engaged for the Hauptwerk division. Due to this type of mechanical linkage you may also access the Oberwerk division through the pedal by coupling the manuals and also the pedals. Then by depressing a pedal key you would also engage the Hauptwerk key which engages the Oberwerk key. Similar to the stop controls, either coupler will engage the other from either display page. Generals- We have included 10 General "pistons" to facilitate registration changes by using keyboard pistons or other MIDI devices. These Generals are only found on the Stop Controls page and appear as stop knobs in two columns down the center of the screen. You will also find a SET piston marked as "S" and the General Cancel piston marked as "C". To set the Generals simply choose your registrations by engaging the stop knobs, engage the "S" piston then engage any of the Generals 1-10. Your registration will be stored in the combination system memory. Disengage the "S" piston to release the organ from capture mode. The General Cancel "C" piston will clear any stops or couplers that are engaged and return them to their off position (this does not include the WIND stop which activates the blower and turns the organ on.) You may wish to save your registrations to a file which may be done by choosing Combination|Save combinations as... then give your combination file a name and choose save. The next time you load the organ you may recall this registration file by choosing Combination|Load combination file... or you may set Hauptwerk to automatically load the last used combination file upon organ load up. Please refer to your Hauptwerk user manual for more information on combination files. Silbermann St. Georgenkirche User Guide Combination Files- We have included a special combination file setting which contains several standard Silbermann registrations. These combinations are preset into the organ definition file and are ready to use upon organ load up. We have also included a list of the Silbermann registrations for those wanting to read through them and perhaps modify them according to the various options Silbermann provided which may be found on the last page of this document. To recall these registrations you may use the Generals provided for use on the Stop Controls display page. You may create your own combinations and store these as individual combination files under the Hauptwerk 2 Combinations|Save combination as... menu option. Be sure to give your combinations a meaningful name to recall for later use. Note that General 8 is not included on the Silbermann registration list and we have made this to make use of all Generals. Temperament Files- In the DVD-Rom folder files/installation-files you will find an installation file called Silbermann-St-Georgenkirche-Temperaments.CompPkg.Hauptwerk.rar. You may install this in the same manner that the samples and organ definition files were installed using the Hauptwerk 2 installer. Since the organ is tuned to A=465 if you choose an included Hauptwerk 2 temperament which is preset to A=440 the entire organ will be retuned down one semi-tone. In order to keep the organ at its normal pitch special temperament files were created which adjust the pitch ratios for tuning of one semi-tone higher than A=440 and keep the organ at A=465. We have included 6 temperaments for use with this organ, the Silbermann, Kirnberger III, Werckmeister III, Meantone Quarter Comma Pietro Aaron, Kellner and the new Bach-Lehmann temperament. Note that all files begin with the text Roetha_... which distinguishes these from the default temperaments included with Hauptwerk 2. Of course users also have the option to play the organ at its original recorded pitch. You may choose to do this by choosing 'Temperament|Original organ tuning' while the organ is loaded, or by using the 'General settings|General options' screen and edit the 'Temperament loading mode when loading an organ' drop down menu. If you choose to use one of the default temperaments included with Hauptwerk 2 which are all A=440 temperaments then the entire organs pitch will shift down one semi-tone.