DOCSLIB.ORG

General Rules for the Sandy Pines Cardboard Boat Race

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
General Rules for the Sandy Pines Cardboard Boat Race GENERAL RULES FOR THE SANDY PINES CARDBOARD BOAT RACE Build Rules The entire boat must be built out of corrugated or standard cardboard, this cardboard may be as thick or have as many layers as you want. You may not use Paper-mâché to ‘cover’ the hull although it may be used to join cardboard panels or strengthen joints The following materials are also permitted in the construction: Brown wrapping paper, Newspaper, Tissue paper, Cardboard tubes Duct tape, masking tape, gaffer tape and packing tape along with adhesives such as PVA Glue, “liquid nails” or silicone may be used to connect cardboard-to-cardboard or reinforce seams, stress points & joints. Tapes may not be used to waterproof hulls and may not be 'Wrapped' around the hull The following paint types are permitted to help water-seal the hull joints & edges: Rubber ('Caucho'), Standard interior/exterior emulsion paint, one-part polyurethane varnish, Water- based sealant Applied paint, glue & silicone must be dry for at least 24 hours prior to launching, boats that have wet paint or other materials may be disqualified Oars & Paddles must be ‘Homemade’ and are under the same build-restrictions as hulls. Although wooden broom-handles may be used for shafts or handles, the blades themselves must be made from cardboard, however edges can be taped & siliconed if required, but not 'wrapped' in tape or film. Tie- wraps may be used to join the blades to the handles & the same paint rules apply as with boat construction Decorations and props that are not part of the boat's hull or structure can be made of anything as long as they do not add to the strength, integrity or buoyancy of the boat or are going to be removed from the hull prior to entering the water. If there is any doubt about the construction, race judges reserve the right to use a probe, to test and verify that only permitted materials have been used & no other prohibited matter is present and if necessary they may decide to cut into the boat in order to confirm although if this compromises the structural of waterproofing integrity of the hull, the judge may require the boat to be made available after the race so that the inspection can then be performed by cutting if necessary - any contravention of the rules will result in the offending boat being disqualified and any winning race position would be withdrawn Design is the builder’s choice. Let your imagination run wild, and remember one thing - good taste counts, designs, images or any other display deemed to be inappropriate may result in withdrawal of the offending vessel from the race. Strict 'Don’ts' “Sono-tubes”, (used in the construction world to pour concrete columns) or any other type of pre- treated or coated cardboard that has been processed in such a way as to make the cardboard waterproof must not be used. The hull of the boat must not contain wood, plastic, fiberglass, Styrofoam or any other foam or flotation device, including empty bottles, polystyrene or expanding foam Tar-based substances, epoxy glue, fiberglass resins or waterproofing compounds such as wax are not permitted to be used anywhere in the hull structure Hulls must not be “wrapped” in plastic, duct tape, Cling-film, or anything else of this type and exposed areas of hull may only be painted as per the rules set out above. Metal or plastic staples, clamps, nails, screws, etc. must not be used. These are potentially dangerous to the crews, rescue teams, the public and the environment No batteries or motors may be used in construction of the boat. These may be used for decoration and display purpose during judging only and any battery or motor must be removed prior to the boat entering the water Where the crew sits must not be enclosed. The boat crew must be able to get into and out of the boat easily & without let or hindrance in case of emergency PLEASE NOTE THAT NO BOATS, KYACKS OR SWIMMERS ARE PERMITTED IN THE RACING AREA OF THE LAKE DURING THE RACE TIME. In all cases, Judge’s rulings are final and there are no appeals Race Rules All boats must pre-register on Sandy Pines’ website No later than Sunday, July 18th. Boat check in starts at 9:00am and all boats must be in position at the Phase 4 Beach for judging by 9:45am on Race Day. There are to be a minimum of two (2) persons in every boat, there is no restriction on maximum number of crew. Only up to 4 can paddle. Persons under 12 must wear a lifejacket. Winning boats must be 'Afloat' when they get to the finish point, with a minimum of 2 crew members still aboard, with or without paddles but must still be making way under the power of their own on-board crew. Boats that are being pushed or towed by crew members who are not inside the boat will not be eligible for race position status and will be deemed not to have finished the race Any boat that fails to round any one of the buoys designated as race boundaries will be disqualified and will not be eligible for any race prize position. Safety boat crew and spotters will determine if any boat has failed to complete the course correctly and will report to the judges. Boats may be required to participate in a Qualifying Heat before the Final Heat winner. .
Load more

Recommended publications
  • Cardboard and Brown Paper Bags Office Paper, Newspaper, Junk Mail, Magazines, and Catalogs
    Recycling Center 801 Diamond Valley Drive Open: Daily to the public during daylight hours This guide will help you properly prepare your recyclable materials for drop-off at the Town of Windsor Recycle Center. This is a drop-off facility. It does not have a buy-back option and is for use by residents and small businesses. Following this information will help maintain the facility and the recycling program for the benefit of the community. IMPORTANT… • Do not leave your recyclables in plastic bags. Plastic bags are NOT recyclable! • The plastic item must be a BOTTLE or JAR. with a #1 or #2 on the bottom. • 99 percent of these will have a screw-on plastic lid (which isn’t recyclable). • Plastic containers with a #3 - #7 on the bottom are NOT acceptable. • Tubs, buckets, deli plates, microwave/fast food trays, wrappers, Styrofoam, toys, patio furniture, etc. are NOT acceptable. • Plastic bottles larger than 2.5 gallons are NOT acceptable. • Syringes and other medical supplies are NOT acceptable. Cardboard and Brown Paper Bags Corrugated cardboard is easy to recognize. It is made of paper and has an arched layer called “fluting” between smooth sheets called “liners”. The drop-off site has two 40-yard hydraulic compactor units for collecting corrugated cardboard and brown paper bags. The compaction system is self-activated by depositing the prepared materials into a six-inch tall slot. Flatten boxes. Cut or tear large boxes into sections no larger than 4 feet by 4 feet to prevent jamming the machine. No wet, waxed-coated or food-contaminated boxes.
    [Show full text]
  • Tall Oil Rosin (TOR) Version Number: 8 Issued: 2021-03-15 Replaces SDS: 2019-01-16
    SAFETY DATA SHEET According to Regulation (EC) No 1907/2006 Tall Oil Rosin (TOR) Version number: 8 Issued: 2021-03-15 Replaces SDS: 2019-01-16 SECTION 1: Identification of the substance/mixture and of the company/undertaking 1.1. Product identifier Trade name Tall Oil Rosin (TOR) CAS No. 8050-09-7 UFI code 5SDP-7PGU-G604-3JPD EC number 232-475-7 REACH registration number 01-2119480418-32 Index No. 650-015-00-7 1.2. Relevant identified uses of the substance or mixture and uses advised against Use Manufacture rosin Rubber production Binders and release agents Coatings Production of paper and cardboard 1.3. Details of the supplier of the safety data sheet Supplier SunPine AB Street address Box 76 941 22 Piteå Sweden Telephone 0911-23 28 00 Email [email protected] Web site www.sunpine.se 1.4. Emergency telephone number NHS 111 1 / 15 SAFETY DATA SHEET According to Regulation (EC) No 1907/2006 Tall Oil Rosin (TOR) Version number: 8 Issued: 2021-03-15 Replaces SDS: 2019-01-16 Available outside office hours Yes SECTION 2: Hazards identification 2.1. Classification of the substance or mixture Classification according to Regulation (EC) No 1272/2008 Danger classes Skin sensitisation, hazard category 1 Hazard statements H317 2.2. Label elements Labelling according to Regulation (EC) No 1272/2008 Hazard pictograms Signal word Warning Hazard statements H317 May cause an allergic skin reaction. Precautionary statements P261 Avoid breathing smoke/fog/vapors/spray. P280 Wear protective gloves/protective clothing/eye protection/face protection. P302 + P352 IF ON SKIN: Wash with plenty of water/soap.
    [Show full text]
  • Corrugated Board Structure: a Review M.C
    ISSN: 2395-3594 IJAET International Journal of Application of Engineering and Technology Vol-2 No.-3 Corrugated Board Structure: A Review M.C. Kaushal1, V.K.Sirohiya2 and R.K.Rathore3 1 2 Assistant Prof. Mechanical Engineering Department, Gwalior Institute of Information Technology,Gwalior, Assistant Prof. Mechanical Engineering 3 Departments, Gwalior Engineering College, Gwalior, M. Tech students Maharanapratap College of Technology, Gwalior, [email protected] [email protected] [email protected] ABSTRACT Corrugated board is widely used in the packing industry. The main advantages are lightness, recyclability and low cost. This makes the material the best choice to produce containers devoted to the shipping of goods. Furthermore examples of structure design based on corrugated boards can be found in different fields. Structural analysis of paperboard components is a crucial topic in the design of containers. It is required to investigate their strength properties because they have to protect the goods contained from lateral crushing and compression loads due to stacking. However in this paper complete and detailed information are presented. Keywords: - corrugated boards, recyclability, compression loads. Smaller flutes offer printability advantages as well as I. INTRODUCTION structural advantages for retail packaging. Corrugated board is essentially a paper sandwich consisting of corrugated medium layered between inside II. HISTORY and outside linerboard. On the production side, corrugated In 1856 the first known corrugated material was patented is a sub-category of the paperboard industry, which is a for sweatband lining in top hats. During the following four sub-category of the paper industry, which is a sub-category decades other forms of corrugated material were used as of the forest products industry.
    [Show full text]
  • Corrugated 101! ! !Corrugated Vs
    Corrugated 101! ! !Corrugated vs. Cardboard! • The term "cardboard box" is commonly misused when referring to a corrugated box. The correct technical term is "corrugated fiberboard carton.”! • Cardboard boxes are really chipboard boxes, and used primarily for packaging lightweight products, such as cereal or board games.! • Corrugated fiberboard boxes are widely utilized in retail packaging, shipping cartons, product displays and many other applications ! requiring lightweight, but sturdy materials.! !Corrugated Composition! Corrugated fiberboard is comprised of linerboard and heavy paper medium. Linerboard is the flat, outer surface that adheres to the medium. The medium is the wavy, fluted paper between the liners. Both are made of a special kind of heavy paper called !containerboard. Board strength will vary depending on the various linerboard and medium combinations.! • Single Face: Medium glued to 1 linerboard; flutes exposed! • Single Wall: Medium between 2 liners! • Double Wall: Varying mediums layered between 3 liners! !• Triple Wall: Varying mediums layered between 4 liners! !Flute Facts! !Corrugated board can be created with several different flute profiles. The five most common flute profiles are:! • A-Flute: Original corrugated flute design. Contains about 33 flutes per foot.! • B-Flute: Developed primarily for packaging canned goods. Contains about 47 flutes per foot and measures 1/8" thick! • C-Flute: Commonly used for shipping cartons. Contains about 39 flutes per foot and measures 5/32" thick! • E-Flute: Contains about 90 flutes per foot and measures 1/16" thick! • F-Flute: Developed for small retail packaging. Contains about 125 flutes per foot and measures 1/32" thick! • Generally, larger flute profiles deliver greater vertical compression strength and cushioning.
    [Show full text]
  • VNP Guideline LCA Data for Paper and Board in the Netherlands
    VNP Guidelines - LCA data for paper and board products It is of high importance that the data which isused from generic LCA databases (e.g. ecoinvent) are recent as well as representative for the kind of material used. Paper and board are complex materials that appear in different types suitable for the various applications. This document is set-up to assist LCA experts in finding the right data belonging to the type of paper and board studied. General advices: It is not advisable to use the data from European Life Cycle Database (ELCD) as these data are incomplete and also only ‘cradle to grave’: these are aggregated data hence difficult to identify where impacts come from and thus hardly usable for comparisons or to change for specific situations. Of all other generic databases ecoinvent is the most complete and current database. Other public datasets (e.g. GaBi, Base Impacts and ProBas) are less current and less easy to interpret from a user point of view. For LCA assessments on paper and board produced in the Netherlands it is essential to replace the input of the European average enery mix with input the Dutch energy mix. (NB this is not possible with ELCD as these allow no changes at all). Packaging paper Paper for corrugated board - Papier voor golfkarton Description Corrugated board (in Dutch: golfkarton) is the most commonly used transport packaging. Corrugated board consists of one or more layers of corrugated paper, in combination with one or more layers flat paper. The corrugated paper is called fluting or medium. The flat papers are called liners.
    [Show full text]
  • Wood Research the Influence of the Type And
    WOOD RESEARCH 52 (4): 2007 79-88 THE INFLUENCE OF THE TYPE AND PREPARATION OF LIGNOCELLULOSE FIBRES ON THE PROPERTIES OF MDF Piotr Borysiuk, Danuta Nicewicz, Jerzy Pawlicki , Marcin Klimczewski Faculty of Wood Technology (WTD) SGGW Warszawa, Warsaw, Poland ABSTRACT Th e infl uence of the type and preparation of lingo-cellulose fi bres on the properties of MDF. Th e possibilities of utilizing waste-paper were examined in the production of MDF. Two kinds of waste-paper (cardboard waste and mixed waste-paper) in two disintegration sizes each were used. Th e composition and length of fi bres and content of the Klasson lignin were examined. Th e following properties were obtained in the boards: bending strength, internal bond, modulus of elasticity and thickness swelling. It is apparent that paper fi bres can be added to wood fi bers in the production of MDF to a maximum of 30%. KEY WORDS: cardboard waste, mixed-waste paper, MDF, disintegration size of waste paper INTRODUCTION Th e limited supply of wood from the forest has initiated research in other materials for production of wood- panel boards. Investigations of the utilization of fi brous agricultural waste material and of high-molecular polymer are well-known and partially practised in industry. Waste paper is a recycled material which is not on the whole used in the production of paper. Th e production and consumption of paper increase every year, this is why waste paper resources will also increase. Th is is the reason why waste paper can be used in other branches of industry.
    [Show full text]
  • What's a Tree Done for You Lately?
    What’s a Tree Done For You Lately? Some common products we get from trees and how they are made Scott Leavengood Director, Oregon Wood Innovation Center, Oregon State University This publication is on-line at http://owic.oregons tate.edu/teachers.php Introduction Products from trees are all around us. Some items are easy to recognize as products we get from trees - This publication will serve as valuable lumber, plywood, and paper, for example. Other background material for several activities in the items such as cellophane, a rayon scarf, and a Project Learning Tree (PLT) Pre K-8 chocolate bar, may not be as easy to recognize as a Environmental Education Activity Guide (1993, product from trees. American Forest Foundation, Washington, D.C.). In particular, the publication is well- This publication will help educators teach students suited to activities 12 and 13, Tree Treasures, about the variety of products we obtain from trees and We All Need Trees, respectively. and how the products are made. It serves as a reference for anyone who wants to know more Number 12 - Tree Treasures about products we obtain from trees. Objectives: 1) identify and categorize products derived from Products from trees may be categorized as: trees, 2) find out which forest products are recyclable • products from wood fiber - for example, paper or reusable, and products and purified cellulose products (rayon, 3) recommend actions for conserving forest cellophane, food additives, and resources. pharmaceuticals); Number 13 - We All Need Trees • products derived
    [Show full text]
  • Corrugated Cardboard Magazines
    Most of us use a paper product every day. That's because paper products make up about 71 million tons (or 29 percent) of the municipal waste stream, according to the Environmental Protection Agency (EPA). The good news is that more and more Americans are recycling paper. In fact, upwards of 63 percent (45 million tons) is recycled annually. When you break that number down by population, roughly 334 pounds of paper is recycled for every person in the United States. Corrugated Cardboard Currently, about 70 percent of cardboard-boxes shipped commercially are recovered for recycling. Many of the boxes are themselves made of recycled materials or lumber industry byproducts like sawdust and wood chips. When recycled, cardboard is used to make chipboard like cereal boxes, paperboard, paper towels, tissues and printing or writing paper. It's also made into more corrugated cardboard. How It's Recycled: 1. The cardboard is re-pulped and the fibers are separated and bleached. This is a chemical process involving hydrogen peroxide, sodium silicate, and sodium hydroxide. 2. The fibers are screened and cleaned to eliminate contaminants. 3. The fibers are washed to remove leftover ink. 4. Fibers are pressed and rolled into paper. 5. he rolls of paper are then converted into boxes or made into new products. Magazines Magazines are made from paper that's been buffed and coated to achieve a glossy appearance. Next, the paper is covered with a white clay that makes color photographs look more brilliant. The shiny appearance does not contaminate the paper at all. About 45 percent of sub-content-3 are being recycled today.
    [Show full text]
  • Chapter 6 Corrugated Cardboard Packaging Section 6.0 General Information
    Chapter 6 Corrugated cardboard packaging Section 6.0 General information 6.0.0 Contents 6.0 General information 6.0.0 Contents 6.0.1 Introduction 6.0.2 Application 6.0.3 Module systems 6.0.4 Approval for dangerous substances 6.0.5 Quality requirements 6.0.6 Recovery systems Status: October 2012 Packaging Handbook 1 Chapter 6 Corrugated cardboard packaging Section 6.0 General information 6.0.1 Introduction Corrugated cardboard packaging is produced out of renewable raw materials, which can be optimally integrated into cycles of valuable substances. The packaging material connects effective product protection with very low material usage and low weight as well as their outstanding mechanical processability. Therefore, their economic and ecological advantages are linked ideally. The good physical characteristics enable a wide range of applications due to the flute profiles and their combinations. Corrugated cardboard is according to DIN 55405 cardboard made up of one or more layers of corrugated paper, which is glued to one layer or between several layers of paper or cardboard. Corrugated cardboard is distinguished between single-layer or multi-layer cardboard. Corrugated cardboard is manufactured in a continuous automated process from pre-made paper and cardboard. Structure of corrugated cardboard The type of flute mainly used is the circular flute shape (sinus wave) Status: October 2012 Packaging Handbook 2 Chapter 6 Corrugated cardboard packaging Section 6.0 General information 6.0.1 Introduction For corrugated cardboard the size of the flutes determines their nomenclature and their main point of usage. Flute coarse springs well, has good cushioning properties.
    [Show full text]
  • Paper & Cardboard
    Paper & cardboard Exam expectations Knowledge about materials is always tested in the written paper. You are expected to know about paper/card and at least one other material area. Know about paper/card • Where it comes from • How it is made • How products are cut from paper/card Materials and components • In what stock sizes and forms is paper/board supplied? • Is it a renewable/non-renewable material? • How are papers and cardboards classified (grouped)? • What properties do different papers/boards have? • What are components and why are they used? • What are combined materials? Standard stock forms Most materials are supplied in standard stock forms. When specifying paper and cardboard you would choose the size (A1, A2, A3, A4 etc.) then you would choose the weight (grams per square metre). It is usually best to use standard stock forms: • The printing industry need consistent sizes and qualities • Makes it cheaper to buy in this form • Non-standard can greatly increase the costs Paper • Paper is a web-like material made from very fine vegetable fibres. • These fibres usually come from wood pulp although sometimes plants such as flax and hemp are used. • The fibres are made of cellulose and they stick to each other to form a strong web • Recycled fibres are often mixed with new or “virgin” materials Making Paper Papermaking has been around for 2,000 years although it is now highly automated Boiled up to make wood pulp Trees cut & Water added shredded Chemicals and dyes added Pulp poured over fine mesh and squeezed between rollers Fibres • When plants are used to make paper, it is usually necessary to use a special chemical process to break down the lignin found inside the cell walls of the plant.
    [Show full text]
  • Wood-Based Paper and Alternative Fiber-Based Paper the Facts
    Wood-based Paper and Alternative Fiber-based Paper The Facts Wood and recovered paper are the dominant fiber resources for today’s global pulp and paper industry, accounting for 97% of the world’s fiber utilization. The remaining 3% is alternative fibers1 such as bamboo, kenaf, certain grasses and agricultural residues such as bagasse, which results from the processing of sugar cane into sugar, and wheat straw, which is the stalk left over after the wheat grains are harvested. These alternatives fibers for papermaking can be sustainable under certain conditions, and companies, particularly those in countries where wood fiber is scarce, continue to explore the market viability for alternative fiber papers. To ensure paper buyers and end-users are able to make informed decisions about the products they purchase, it’s vital that all claims related to environmental sustainability are substantiated with credible scientific and technical data, regardless of the type of fiber used. Paper: Then and Now Sustainability Case for Wood Fiber Papers Paper is manufactured using renewable, natural fibers. Linen Sustainable Forestry and cotton rags were the main raw materials for the pulp and paper industry from the mid- to late 1880s and even today, Wood-based paper and packaging manufactured in North cotton linters (the fine fibers left on the seed of a cotton plant America are inherently sustainable because they are made from after the ginning process) or cotton clippings from textile mills are a renewable resource – trees grown in responsibly managed used to make some fine papers. But in the early to mid-1900s, forests.
    [Show full text]
  • Building + Assembling the Wall
    BUILDING + ASSEMBLING THE WALL The Trash Wall project is focused on building an extra insulation layer that could be placed in the interior Construction time varies based on the different Burn Test Data of a home to act as a barrier to heat loss or entry. structures and skin types. Sampled were exposed to 400 W flame produced by This wall is to be easily manufactured, such that a a propane torch at a distance of 1 inch until the flame low income individual or family could construct and Insulation Values. Both the shredded paper and burned through the wall. The burn time and the burn install one with minimal expense and maximum cellulose’s insulation effectiveness has been tested. It area were obtained. benefit. Below are two proposed structures for the was found that the shredded paper has an R-value of wall. The upper structure is made with cardboard R-10 US and the cellulose has an R-value of R-12 US. Material: 2 and cardboard tubes, while the lower structure is These values meet the team’s expectations. When burn time (burn area in ) made with cardboard and plastic bottles. Once the testing a section of the trash will filled with shredded structure is built, it can be filled with either shredded paper, the R-value of the wall was found to be R-7 US. 0.2” layer of papercrete: 2 paper or cellulose. From there, a front cardboard 30 seconds (9.6 in ) Fire safety is extremely important when it comes Fabric treated with flour-borax-water mixture: face can be attached to the structure (to hold the 2 insulation in) and a front skin can be attached.
    [Show full text]