Audi Video Interface Manual
Total Page:16
File Type:pdf, Size:1020Kb
High-Definition Link for Audi Manual car-solutions.com www.car-solutions.com [email protected] Contents • Cautions_____________________________________________________________ 3 • Dimension & Exterior_________________________________________________ 4 • Components & Optional parts_________________________________________ 5 • Full Installation Diagram______________________________________________ 6 • CAN wires information(exceptions____________________________________) 7 • HDMI Connection Diagram____________________________________________ 8 • Navigation Connection Diagram(Type A & B) ___________________________ 9 • Compatibility Chart for Navigation(GPS) box models ___________________ 10 • LVDS Connection Diagram___________________________________________ 11 • Body Connector specifications_______________________________________ 12 • Car Compatibility Chart______________________________________________ 13 • Activation by original buttons of Audi _________________________________ 14 • DIP Switch Settings_________________________________________________ 15 • Settings 1. Enter into the setting menu____________________________________ 16 2. HDMI mode settings___________________________________________ 17 3. NAVI mode settings____________________________________________ 17 4. Rear view camera settings_____________________________________ 18 5. AV1(Front view camera) settings________________________________ 18 6. Automatic activation function(AV1) _____________________________ 19 7. AV2 settings__________________________________________________ 19 8. System settings_______________________________________________ 20 9. System information____________________________________________ 20 10. Informationcar-solutions.com of Dip switch settings ______________________________ 21 www.car-solutions.com [email protected] Cautions • You should check the names and colors of each wires exactly, before you connect the wires. ex) CAN HIGH: White wires / CAN LOW: Blue wires • The ‘POWER / CAN Cable’ should always be connected last and be disconnected first. • The 'Mode Switch' is an optional part to change modes forcibly without CAN-BUS. Generally, the CAN-BUS wires are connected for changing modes by original buttons. • When the reverse gear is not detected by CAN-BUS, the 'REVERSE 12V IN wire’ should be spliced with 12V power of reverse light. HDMI device-related • HDMI mode accepts general-screen resolution of HDMI devices. If screen size of HDMI does not fit on the monitor, should adjust screen size & position in 'settings mode'. • Generally, '5V 1A Power output(5V USB POWER)' is a standard voltage for charging smartphone. If you need higher voltage than 5V, you should add a separate power supply. Navigation(GPS) box-related • When you connect the power wires(B+, ACC) to the navigation(GPS) box, the 'ACC (12V) OUT' wire supported by device should be spliced with an ACC wire of navigation box. • After installation is done, select an applicable navigation(GPS) box model in the 'Navigation model selection menu' of setting car-solutions.commode. • The navigation box should be powered off before unplugging the HDMI cable. 3 www.car-solutions.com [email protected] ⓐ ⓑ ⓒ ⓓ ⓔ Exterior ⓐ DIP SWITCH ⓑ AV IN / OUT ⓒ TOUCH IN ⓓ MODE ⓔ POWER / CAN ⓕ HDMI IN ⓖ 5V USB POWER ⓗ NAVI IN ⓘ UART I/F ⓙ LVDS OUT ⓕ ⓖ ⓗ ⓘ ⓙ car-solutions.com www.car-solutions.com [email protected] 4 Components Power / CAN Cable LVDS Cable LVDS PCB HDMI Cable AV IN / OUT Cable 5-pin Micro USB Cable Optional Parts(sold separately) Optional Parts(purchased separately) TTA 24-Pin to HDMI Gender Touch-IN Cable Mode Switch iNAVI CUBE LCD Cable HDMI Cable HDMI extender (For iNAVI CUBE) car-solutions.com(Male to Male) (For stick type HDMI device) 5 www.car-solutions.com [email protected] Touch screen panel Full Installation Diagram GND Input MMI DATA Pin Specification B+ Power Input 1 5 9 13 10 ※ Optional External Devices Mode GND Output 12V ACC Power Touch IN Cable Switch Output (Navigation Power) (Installation Type A) (optional) 4 8 12 16 RV-CAM Video Input External Rear View 12V Power Output & GND Output(RV-CAM Power) Camera Reverse Signal Detection(optional) MON CAN wires (Some vehicles should be connected the 'MON CAN wires'.) MMI 3G Plus & MMI 3G Head Unit Original Main-Harness AUDI MMI(Green) DIP S/W Setting Power / CAN Pin # 10 = MMI DATA(Yellow / White) Cable or (Light Green) NAVI Audio Input PAS CAN HIGH & LOW <A4, A5, A6, A7, A8, Q5, Q7> Audio(AUX) Output of Navigation Box 1 2 3 4 5 Audio Output Auxiliary(AUX) PAS CAN H(White) * 20-Pin Connector of Climate controller Input of the car Pin # 4 = CAN HIGH(Orange / Blue) or (Orange / Light Green) Pin # 5 = CAN LOW(Orange / Brown) PAS CAN L(Blue) * Some vehicles should be connected the CAN wires at the other place. (Please refer to next page.) HDMI USB HDMI HDMI FV-CAM Video Input MMI 3G & 3G+ Head Unit(OEM) (AV1) External Front View Camera HDMI HDMI LVDS IN / OUT Connection LVDS IN / OUT car-solutions.comHDMI AV-Input(AV2) PCB AV device (ex: DTV Box, Divx) 6 www.car-solutions.com HDMI Device Navigation Box [email protected] CAN wires information(exceptions) < 2010, 2011 Audi A4 > < 2012~ Audi Q3 > Climate Controller – 20-Pin Connector Climate Controller – 16-pin Connector 1 4 5 9 19 20 10 18 9 12 13 16 POWER / CAN Cable POWER / CAN Cable PAS CAN L PAS CAN L PAS CAN H Pin # 4 = PAS CAN HIGH(Orange / Light Green) PAS CAN H Pin # 12 = PAS CAN LOW(Orange / Brown) AUDI MMI Pin # 5 = PAS CAN LOW(Orange / Brown) AUDI MMI Pin # 13 = PAS CAN HIGH(Orange / Light Green) MON CAN L MON CAN L MON CAN H MON CAN H ACC(12V) OUT Pin # 8 = MON CAN LOW(Orange / Brown) ACC(12V) OUT Pin # 2 = MON CAN HIGH(Orange / Black) GROUND GROUND GROUND Pin # 18 = MON CAN HIGH(Orange / Blue) GROUND Pin # 3 = MON CAN LOW(Orange / Brown) BAT + BAT + Gateway+BEM Module(on the left of the glovebox) – 20-Pin Connector LWR Steuergerät Module(on the glovebox) – 26-Pin Connector 1 11 8 10 1 2 3 13 18 car-solutions.com20 • Normally, general models of Audi should be just connected the ‘PAS CAN High, Low wires’ at the climate controller. • But, some models have different CAN-BUS data. Please refer to above pictures and connect the CAN wires. 7 www.car-solutions.com [email protected] HDMI Connection Diagram HDMI Device HDMI Device HDMI IN 5V USB NAVI IN UART I/F LVDS OUT HDMI IN 5V USB NAVI IN UART I/F LVDS OUT POWER POWER HDMI USB HDMI USB HDMI HDMI (5V-1A Power output for HDMI Device) (5V-1A Power output for HDMI Device) (Male) (Female) (HDMI Extender) (HDMI Cable) ‘Stick Type’ HDMI Devices ‘Dongle & Adapter’ Type HDMI Devices car-solutions.com 8 www.car-solutions.com [email protected] Navigation Connection Diagram(Type A) Navigation Connection Diagram(Type B) Navigation(GPS) Box Navigation(GPS) Box HDMI IN 5V USB NAVI IN UART I/F LVDS OUT HDMI IN 5V USB NAVI IN UART I/F LVDS OUT POWER POWER TOUCH IN HDMI HDMI Touch screen panel HDMI Touch screen panel Gender (TTA 24-pin to HDMI) LCD Cable (Touch panel cable) LCD HDMI (TTA 24-pin to TTA 24-pin) Cable car-solutions.com iNAVI - CUBE iMERCURY – Class Settop 9 www.car-solutions.com [email protected] Compatibility Chart for Navigation(GPS) box models – Korea Market Installation Model Country Dip S/W Required Parts (Navigation) Type CUBE(Light) South Korea Type A - iNAVI Gender CUBE LCD Touch-IN (TTA 24-pin HDMI Cable OFF(↑): 1, 2, 3, 4 Cable(iNAVI) Cable to HDMI) (Male to Male) Class Settop South Korea Type B - iMERCURY ON(↓): 1, 2, 3 HDMI Cable OFF(↑): 4, 5 (HDMI to HDMI) • The device supports navigation(GPS)car-solutions.com box models equipped with 'Digital video output'. • It does not support the 'RGB video'. 10 www.car-solutions.com [email protected] LVDS Connection Diagram LVDS Connection HDMI IN 5V USB NAVI IN UART I/F LVDS OUT POWER MMI 3G Plus & 3G Head Unit HDMI • 'Genuine(OEM) LVDS connector' should be connected to 'LVDS IN / OUT PCB'. • ‘Provided LVDS connector' should be connected to the head unit instead to the genuine connector. Genuine Monitor(OEM) LCD Cable (Provided LVDS Cable) LVDS IN / OUT HDMI car-solutions.comPCB (OEM LVDS Cable) 11 www.car-solutions.com [email protected] Body Connector specifications POWER / CAN MODE TOUCH-IN AV IN / OUT DIP SWITCH 1 2 3 4 5 6 7 8 9 10 11 1 2 3 4 5 6 7 8 9 10 1 2 1 2 3 4 12 13 14 15 16 17 18 19 20 21 22 Length: 100 cm Length: 20 cm REAR CAMERA REAR NAVI AUD IN R AUD NAVI NAVI AUD IN L IN AUD NAVI AUDIO OUT R AUDIO AUDIO OUT L AUDIO AV2 IN R AV2 AV2 IN V AV2 IN L AV2 AV1 IN V AV1 ACC(12V) OUTACC(12V) MON CANH MON MON CANL MON REVERSE 12V IN 12V REVERSE PAS CAN H CANPAS PAS CAN L CANPAS AUDI MMI AUDI GROUND GROUND REAR 12V REAR GROUND BAT + BAT IR OUT IR Length: 150 cm Length: 150 cm 1 BATTERY POWER INPUT 1 RV-CAM VIDEO INPUT 12 GND(RV-CAM VIDEO) 2 GND INPUT 2 RV-CAM POWER OUT 13 GND OUTPUT(RV-CAM) 3 GND OUTPUT 3 REVERSE DETECTION 14 IR OUT 4 ACC(12V) POWER OUTPUT 4 NAVI AUX INPUT R 15 GND(NAVI AUX IN R) 5 MONITOR CAN HIGH 5 NAVI AUX INPUT L 16 GND(NAVI AUX IN L) 6 MONITOR CAN LOW 6 AUDIO OUTPUT R 17 GND(AUDIO OUT R) 7 AUDI MMI(Only for AUDI) 7 AUDIO OUTPUT L 18 GND(AUDIO OUT L) 8 - 8 AV1 VIDEO INPUT 19 GND(AV1 VIDEO IN) 9 PAS CAN HIGH PUSH SWITCH TOUCH-IN 9 AV2 VIDEO INPUT 20 GND(AV2 VIDEO IN) 10 PAS CAN LOW CABLE 10 AV2 AUDIO INPUT R 21 GND(AV2 AUDIO IN R) car-solutions.com11 AV2 AUDIO INPUT L 22 GND(AV2 AUDIO IN L) • The colors of each wires can be changed under manufacturer’s circumstance. 12 www.car-solutions.com [email protected] Car Compatibility Chart Production Car Models Specific Models Year A4 2010 - B8 A5 2009 - 8T A6 2010 - 2011 C6(MMI 3G) A6 2011 - C7 The device is used in combination with Audi MMI(Multi Media Interface) A7 2010 - 4G system.