DOCSLIB.ORG

Design Guidelines for the Thermoforming Process 1

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Design Guidelines for the Thermoforming Process 1 Design guidelines for the thermoforming process 1 Design guidelines for product engineers on the thermoforming process U aangeboden door: Batelaan Kunststoffen BV ● Veerpolder 8 ● 2361KV Warmond T: 071-5613301 ● F: 071-5616701 ● www.batelaan.nl Zonder schriftelijke toestemming van de ProducentenVereniging Thermoplasten (PVT) mag niets uit deze informatiemap worden verveelvoudigd en/of openbaar gemaakt door middel van druk, fotokopie, microfilm of anderszins, hetgeen ook van toepassing is op de gehele of gedeeltelijke bewerking. Deze informatiemap is gebaseerd op de trainingmodules, gerealiseerd in het kader van T-ForM. Voor de eventuele aanwezigheid van (zet)fouten en onvolledigheden kan de PVT geen aansprakelijkheid aanvaarden. PVT, Postbus 420, 2260 AK Leidschendam, [email protected] www.t-form.eu July 2008 1 Design guidelines for the thermoforming process 2 Contents Contents ................................................................................................................................ 1 1. Executive Summary ........................................................................................................... 5 2. Introduction ........................................................................................................................ 9 2.1 Thin Sheet Thermoforming ........................................................................................... 9 2.2 Thick Sheet Thermoforming ....................................................................................... 10 2.3 Tooling ....................................................................................................................... 10 2.4 Literature .................................................................................................................... 11 3. Thermoforming process ................................................................................................... 15 3.1 Bubble Forming .......................................................................................................... 15 3.2 Cavity Forming ........................................................................................................... 15 3.3 Drape Forming ........................................................................................................... 17 3.4 Variations to Avoid Excessive Thinning ..................................................................... 18 3.4.1 Cavity Forming with Plug Assistance ................................................................... 18 3.4.2 Billow Drape Forming ........................................................................................... 19 3.4.3 Snap-Back Forming ............................................................................................. 19 3.4.4 Reverse Draw with Plug-Assist Forming .............................................................. 19 3.4.5 Twin Sheet Forming ............................................................................................. 19 3.4.6 Other Techniques ................................................................................................ 21 4. Tooling ............................................................................................................................. 23 4.1 Tooling Costs: Thermoforming versus Injection Moulding ........................................... 23 4.2 Tooling: Design Considerations .................................................................................. 23 4.2.1 Thermoforming Mould Design Criteria .................................................................. 24 4.3 Heat Transfer Considerations ..................................................................................... 26 4.3.1 Mould Temperature Control .............................................................................. 27 4.4 Tooling Materials ........................................................................................................ 27 4.1.1 Wood ................................................................................................................... 30 4.4.2 Plaster ................................................................................................................. 30 4.4.3 Sprayed Metal Alloys ........................................................................................... 31 4.4.4 Resin Tooling ....................................................................................................... 31 4.4.5 Aluminium ............................................................................................................ 33 4.4.6 Steel .................................................................................................................... 33 4.4.7 Russian Tooling Practice ..................................................................................... 33 5. Proprietary resins and resin based materials for tooling ................................................... 37 5.1 Axson EPO 4042 EPO4042/L Epoxy Casting Resin ................................................... 37 5.2 Epon Epoxy Resins .................................................................................................... 37 5.3 Fablite ........................................................................................................................ 38 2 Design guidelines for the thermoforming process 3 5.4 Polylite Polyester Resin .............................................................................................. 38 5.5 Metapor Epoxy/Aluminium .......................................................................................... 38 5.6 Espor .......................................................................................................................... 40 5.7 Vestalloy ..................................................................................................................... 40 5.8 WIS Tooling ................................................................................................................ 41 5.9 Albright RT ................................................................................................................. 41 5.10 Poly Steel ................................................................................................................. 41 5.11 Microsyn ................................................................................................................... 41 5.12 Ren-Shape (Vantico) ................................................................................................ 42 5.13 Polyurethane Machinable Slab (Ureol Board Axson) ................................................ 43 5.14 Epoxy / Aluminium using Stereolithography (Escuelo Technica)............................... 43 5.15 Miscellaneous Materials ........................................................................................... 43 6. Tooling: plug assistance................................................................................................... 47 6.1 Plug Assisted Thermoforming ..................................................................................... 47 6.2 Plug Materials............................................................................................................. 49 6.2.1 Acetal (e.g. Delrin) ............................................................................................... 52 6.2.2 Hardened Felt ...................................................................................................... 52 6.2.3 Syntactic foam ..................................................................................................... 52 6.2.4 Wood ................................................................................................................... 52 6.2.5 Resins .................................................................................................................. 52 6.2.6 “Hytac” Syntactic foams ....................................................................................... 52 6.3 Friction Between Plug and Sheet................................................................................ 54 6.4 Mould Plug and Heat Transfer .................................................................................... 62 6.5 Plug Assisted Forming Experimental Work ................................................................. 62 7. Computerised process simulation .................................................................................... 67 7.1 Background ................................................................................................................ 67 7.2 Forming feometries..................................................................................................... 70 7.3 Computer simulation literature summary .................................................................... 71 8. References ...................................................................................................................... 77 Appendix .............................................................................................................................. 80 Planoxal-50 Aluminium Data Sheet .................................................................................. 81 RenShape® BM 5055 ..................................................................................................... 83 EPO 4042 / EPO 4042/L .................................................................................................. 85 LAB 1001 ........................................................................................................................
Load more

Recommended publications
  • A Low Cost Vacuum-Forming System1
    A LOW COST VACUUM-FORMING SYSTEM1 James P. O'Leary, M.S.2, Edward A. Bianchi, B.S.2, and Richard A. Foulds, M.S.2 Vacuum-forming is an excellent method for molding sheets of plastic into complicated shapes. It is just beginning to be used in the field of re­ habilitation medicine where the need to make devices that fit the human form is great. This article describes a new, inexpensive apparatus which enables orthotists and prosthetists to use the vacuum-forming process in their work with a very small outlay of capital. Very little training is required to use the apparatus, and it is now being made available in limited quantities. In the vacuum-forming process a sheet of hot, pliable plastic is drawn either into or around a mold with the use of suction provided by a vac­ uum pump. When the plastic cools and hardens, it retains the shape caused by the mold. An example of the usefulness of a molded orthosis is Fig. 1. A molded ankle-foot orthosis (left) is contrasted shown in Figure 1. to the conventional metal and leather orthosis that it The process, though simple, when adapted to replaces. Besides being lighter in weight, the plastic the needs of mass-production, requires very ex­ orthosis requires no modification to the shoe. This pensive machinery. Until recently only industrial feature makes it possible for the patient to interchange shoes easily. vacuum-forming equipment was available, with prices ranging from $4,000 to over $125,000. Because of the large investment in money and space required to obtain and use the machines With these thoughts in mind we designed and designed for mass production, very few medical built a vacuum-forming apparatus called the facilities have made use of the vacuum-forming "Bracemaker" (Fig.
    [Show full text]
  • Thermoforming
    APPLICATION GUIDE: Thermoforming TIME REQUIRED COST SKILL LEVEL By Brian Sabart, Stratasys Inc. and Jeff Gangel, Formech International, Ltd. OVERVIEW Vacuum Forming Materials: Thermoforming is a relatively simple manufacturing process that is inexpensive when compared to other - ABS plastic molding and forming methods. Although thermoforming is often associated with manufacturing - Polyvinylchloride (PVC) of packaging items such as blister packs and disposable coffee cup lids, the cost and time advantages - Polycarbonate (PC) are realized in a broad spectrum of products in an equally broad range of industries. When using a Fortus - Polyethylene (PE) 3D Production System with FDM technology to construct thermoforming tooling, the process becomes - Low Density Polyethylene (LDPE) simpler, more efficient and increasingly cost-effective. - High Density Polyethylene (HDPE) - Polypropylene (PP) - Polystyrene (PS) PROCESS DESCRIPTION - Polyphenylene Oxide (PPO) Thermoforming is a collection of manufacturing methods that heat and form sheets of extruded plastic. - Polyphenylene Ether (PPE) Thermoforming processes include drape, vacuum and pressure forming. - Polymethyl-Methacrylate (PMMA) - Acrylic Drape forming relies on gravity to pull the sheet against the tool. Vacuum forming, as the name implies, - Closed Cell Foam Polyester (PBT, PET) draws the heated sheet against the tool with the assistance of a vacuum. Pressure forming combines - Polyester Copelymer (PETG) vacuum and pressure to simultaneously pull and push the plastic sheet to the contours of the tool. - Thermoplastic Olefin (TPO) - Thermoplastic Elastomer (TPE) This process guide documents the steps for vacuum forming since it is the most common thermoforming - Thermoplastic Rubber (TPR) method. However, many of the details presented may also be applied to drape and pressure forming.
    [Show full text]
  • Radel® PPSU, Udel® PSU, Veradel® PESU & Acudel® Modified PPSU
    Radel ® | Udel ® | Veradel ® | Acudel ® Radel® PPSU, Udel® PSU, Veradel® PESU & Acudel® modified PPSU Processing Guide SPECIALT Y POLYMERS 2 \ Sulfone Polymers Processing Guide Table of Contents Introduction ............................. 5 Part Ejection . 14 Draft . 14 Ejector pins and/or stripper plates . 14 Sulfone Polymers........................ 5 Udel® Polysulfone (PPSU) . 5 Injection Molding Equipment ............. 15 ® Veradel Polyethersulfone (PESU) . 5 Controls . 15 ® Radel Polyphenylsulfone (PPSU) . 5 Clamp . 15 ® Acudel modified PPSU . 5 Barrel Capacity . 15 Press Maintenance . 15 Resin Drying . .6 Screw Design . 15 Rheology................................ 8 Screw Tips and Check Valves . 15 Viscosity-Shear Rate ..................... 8 Nozzles . 16 Molding Process . 16 Resin Flow Characteristics . 9 Melt flow index . 9 Polymer Injection or Mold Filling . 16 Spiral flow . 9 Packing and Holding . 17 Injection Molding . .10 Cooling . 17 Molds and Mold Design .................. 10 Machine Settings ....................... 17 Tool Steels . 10 Barrel Temperatures . 17 Mold Dimensions . 10 Mold Temperature . 18 Mold Polishing . 10 Residence Time in the Barrel . 18 Mold Plating and Surface Treatments . 10 Injection Rate . 18 Tool Wear . 10 Back Pressure . 18 Mold Temperature Control . 10 Screw Speed . 18 Mold Types . 11 Shrinkage . 18 Two-plate molds . 11 Three-plate molds . 11 Regrind ............................... 19 Hot runner molds . 11 Cavity Layout . 12 Measuring Residual Stress ............... 19 Runner Systems . 12 Extrusion............................... 22 Gating . 12 Sprue gating . 12 Edge gates . 13 Predrying ............................. 22 Diaphragm gates . 13 Tunnel or submarine gates . 13 Extrusion Temperatures ................. 22 Pin gates . 13 Screw Design Recommendations . 22 Gate location . 13 Venting . 14 Sulfone Polymers Processing Guide / 3 Die Design ............................. 22 Extruded Product Types . 23 Wire . 23 Film . 23 Sheet . 23 Piping and tubing . 23 Start-Up, Shut-Down, and Purging .......
    [Show full text]
  • Optimizing Thermoforming of High Impact Polystyrene (HIPS) Trays by Design of Experiments (DOE) Methodologies
    Optimizing Thermoforming of High Impact Polystyrene (HIPS) Trays by Design of Experiments (DOE) Methodologies Vishal M. Dhagat Department of Electrical & Computer Engineering, UConn Storrs, CT 06269-4157 [email protected] Ravindra Thamma Manufacturing & Construction Management, CCSU 1615 Stanley Street, New Britain, CT 06050 [email protected] Abstract The process of heating and reshaping plastics sheet and film materials has been in use since the beginning of the plastics industry better known as thermoforming. Today this process is very ubiquitous for industrial products including signage, housings, and hot tubs. It also produces much of the packaging in use today including blister packs, cartons, and food storage containers. The process of thermoforming has many advantages over other methods for producing high quality plastic products, with some limitations, which can be resolved by implementing stringent quality control using scientific methods to improve process performance. Two areas of interest in today’s industry of great concerns are lean manufacturing operations and environment. Thermoforming of high impact polystyrene sheets using vacuum forming technique requires technical knowledge on material behavior, mold type, mold material, and process variables. Research on these various subjects is well documented but very limited research is done in process optimization of HIPS (High Impact Polystyrene). Design of Experiments (DOE) approaches like the face-centered cubic central composite design can be used to refine the process and to minimize rejects. In this paper, we present a case study on thermoforming of HIPS single use trays made on a semi automatic machine using three criteria solely based on the FCC Design method. The optimization of tray forming and wall thickness distribution is explored.
    [Show full text]
  • The Dynisco Extrusion Processors Handbook 2Nd Edition
    The Dynisco Extrusion Processors Handbook 2nd edition Written by: John Goff and Tony Whelan Edited by: Don DeLaney Acknowledgements We would like to thank the following people for their contributions to this latest edition of the DYNISCO Extrusion Processors Handbook. First of all, we would like to thank John Goff and Tony Whelan who have contributed new material that has been included in this new addition of their original book. In addition, we would like to thank John Herrmann, Jim Reilly, and Joan DeCoste of the DYNISCO Companies and Christine Ronaghan and Gabor Nagy of Davis-Standard for their assistance in editing and publication. For the fig- ures included in this edition, we would like to acknowledge the contributions of Davis- Standard, Inc., Krupp Werner and Pfleiderer, Inc., The DYNISCO Companies, Dr. Harold Giles and Eileen Reilly. CONTENTS SECTION 1: INTRODUCTION TO EXTRUSION Single-Screw Extrusion . .1 Twin-Screw Extrusion . .3 Extrusion Processes . .6 Safety . .11 SECTION 2: MATERIALS AND THEIR FLOW PROPERTIES Polymers and Plastics . .15 Thermoplastic Materials . .19 Viscosity and Viscosity Terms . .25 Flow Properties Measurement . .28 Elastic Effects in Polymer Melts . .30 Die Swell . .30 Melt Fracture . .32 Sharkskin . .34 Frozen-In Orientation . .35 Draw Down . .36 SECTION 3: TESTING Testing and Standards . .37 Material Inspection . .40 Density and Dimensions . .42 Tensile Strength . .44 Flexural Properties . .46 Impact Strength . .47 Hardness and Softness . .48 Thermal Properties . .49 Flammability Testing . .57 Melt Flow Rate . .59 Melt Viscosity . .62 Measurement of Elastic Effects . .64 Chemical Resistance . .66 Electrical Properties . .66 Optical Properties . .68 Material Identification . .70 SECTION 4: THE SCREW AND BARREL SYSTEM Materials Handling .
    [Show full text]
  • Equipment Requirements for Vacuum Forming Aristech Surfaces Acrylic Spas, Tub-Showers, Whirlpool Baths, & Small Marine Craft
    TECHNICAL INFORMATION SHEET 4 Equipment Requirements for Vacuum Forming Aristech Surfaces Acrylic Spas, Tub-Showers, Whirlpool Baths, & Small Marine Craft Introduction This Technical Information Sheet was prepared to supplement Aristech Surfaces Technical Bulletins 140, 142, 144, and 152 covering acrylic FRP spas, tub-showers, whirlpool baths, and small marine craft. These bulletins outline the complete process, equipment required and costing information in enough detail to allow a potential manufacturer to design an operating facility provided the technical service offered by the many materials and equipment suppliers is utilized. This document will describe in more detail the equipment required for vacuum forming and supporting the formed unit for fiberglassing. Two types of vacuum forming machines will be specified; a low cost outfit and a higher priced semi-automatic machine. This document is directed to manufacturers of polyester gel coated units who are interested in converting to acrylic surfaced units or wish to add acrylic surfaced units to their current line of products. It is assumed that a manufacturer of gel coated units will not need assistance in fiberglassing the acrylic vacuum formed part once it is jigged since the two processes are nearly identical from that point. After the part is fiberglassed it can be trimmed as gel coated parts are, therefore, no additional information beyond that given in the technical bulletins is supplied. Molds The most economical vacuum forming mold is an exact replica of the finished product made from either tooling grade polyester or epoxy. The master tool used for making Gel Coat molds often will serve as a working vacuum forming mold with minor modifications.
    [Show full text]
  • UV/EB Thermoset Polymers Intended for Thermoforming Applications
    UV/EB Thermoset Polymers Intended for Thermoforming Applications Robert Kensicki Introduction The process of thermoforming is not a new concept as it has been used for many years with the process being refined over the years. The thermoforming process can be defined as simply heating a thermoplastic substrate to a temperature where the substrate becomes soft and flexible. The heated substrate then has a mold or dye forced into it from beneath where a vacuum was pulled to assist the forming. The vacuum pulls the thermoplastic substrate tight to the mold allowing for very detailed parts to be created. Once the vacuum is released and the mold cools the part can be trimmed or cut to the desired shape. Thermoformed parts are used in everyday applications ranging from food packaging, medical packaging, automotive applications, appliances and many others. There are many types of thermoforming methods that vary the thermoforming process and intended applications of the parts made. Some examples of thermoforming processes are vacuum forming, plug and assist forming, billow forming, pressure forming, and drape forming.1The process described above is called vacuum forming. This is the method that this paper will focus on. The process of vacuum forming can be further broken down into two different categories, which are determined by the thickness of the thermoplastic substrate used. These categories are called thin gauge and thick gauge. As the names imply the difference is the thickness of the substrate to be formed. To be considered thick gauge the substrate has to be greater than 3.0 mm whereas the thin film substrate is typically less than 1.5 mm.
    [Show full text]
  • Vacuum Thermoforming Process: an Approach to Modeling and Optimization Using Artificial Neural Networks
    polymers Article Vacuum Thermoforming Process: An Approach to Modeling and Optimization Using Artificial Neural Networks Wanderson de Oliveira Leite 1,*, Juan Carlos Campos Rubio 2, Francisco Mata Cabrera 3, Angeles Carrasco 4 ID and Issam Hanafi 5 1 Departamento de Mecânica, Instituto Federal de Educação, Ciência e Tecnologia de Minas Gerias—Campus Betim, Rua Itaguaçu, No. 595, São Caetano, 32677-780 Betim, Brazil 2 Escola de Engenharia, Departamento de Engenharia Mecânica, Universidade Federal de Minas Gerais, Av. Pres. Antônio Carlos, No. 6627, Pampulha, 31270-901 Belo Horizonte, Brazil; [email protected] 3 Escuela de Ingeniería Minera e Industrial de Almadén, Departamento Mecánica Aplicada e Ingeniería de Proyectos, Universidad de Castilla-La Mancha, Plaza Manuel Meca No. 1, 13400 Ciudad Real, Spain; [email protected] 4 Escuela de Ingeniería Minera e Industrial de Almadén, Departamento de Filología Moderna, Universidad de Castilla-La Mancha, Plaza Manuel Meca No. 1, 13400 Ciudad Real, Spain; [email protected] 5 Ecole Nationale des Sciences Appliquées d’Al Hoceima (ENSAH), Département of Civil and Environmental Engineering, 32000 Al Hoceima, Morocco; hanafi[email protected] * Correspondence: [email protected]; Tel.: +55-31-3597-6360 Received: 16 December 2017; Accepted: 31 January 2018; Published: 2 February 2018 Abstract: In the vacuum thermoforming process, the group effects of the processing parameters, when related to the minimizing of the product deviations set, have conflicting and non-linear values which make their mathematical modelling complex and multi-objective. Therefore, this work developed models of prediction and optimization using artificial neural networks (ANN), having the processing parameters set as the networks’ inputs and the deviations group as the outputs and, furthermore, an objective function of deviation minimization.
    [Show full text]
  • THERMOFORMING Over 50 Years of Thermoforming Experience
    AN INTRODUCTION TO THERMOFORMING Over 50 Years of Thermoforming Experience Placon provides high-quality, custom thermoformed packaging solutions for consumer, industrial, food, and medical products. With over 50 years of thermoforming design and manufacturing experience, you can trust that Placon’s award-winning design and engineering teams will deliver the best packaging solution for your product no matter what industry you are in. Using state of the art design software and a collaborative new product innovation process, our team specializes in delivering a distinctive package that will meet your business objectives on time and within budget. Placon has a reputation in the industry for delivering the highest quality products. We offer: • ISO9001 certification • ISO13485 certification (Elkhart, IN) • ISO14001 compliant • AIB certification (Madison, WI) • SQF certification (West Springfield, MA) • GMP compliant We have multiple clean rooms to serve you: • Elkhart, IN • Plymouth, MN • Madison, WI Team up with us and you’ll benefit from: • More than 250 combined years of design experience with over 700 employees • Exceptional customer service • Rapid prototyping and production-quality samples • In-house tooling and matched-metal thermoforming • Validation process expertise with strict quality control standards (for medical packaging) Continuously setting the bar in plastic packaging solutions, we’re committed to quality with a deep integrity in all that we do. We create packaging breakthroughs that inspire better engagement between people and products. 2 CALL 800.541.1535 TO PLACE AN ORDER Table of Contents 04 WHAT IS THERMOFORMING? 08 COMMONLY USED MATERIALS 11 CONDUCTIVE/ANTISTATIC PRODUCTS 12 TYPES OF STERILIZATION 14 SEALING TECHNIQUES 16 PRODUCT DEVELOPMENT 20 MANUFACTURING ENVIRONMENT 22 ACRONYM INDEX 23 GLOSSARY 24 DATA TABLES PLACON.COM 3 WHAT IS THERMOFORMING? Thermoforming is a process that involves heating a flat sheet of plastic until it is soft enough to mold.
    [Show full text]
  • Rapid Manufacturing of Vacuum Forming Components Utilising Reconfigurable Screw-Pin Tooling
    Rapid Manufacturing of Vacuum Forming Components Utilising Reconfigurable Screw-Pin Tooling by Zhijian Wang, BEng, MSc Thesis Submitted to The University of Nottingham for the degree of Doctor of Philosophy August 2009 ABSTRACT Current market trends are moving from large quantity production towards small batch production and mass customization. This has led to the high demand for the flexibility and adaptability of manufacturing technology and systems. Several reconfigurable pin type tooling systems have been proposed and developed to satisfy such demands. However, these reconfigurable tooling systems still suffer from several drawbacks, including difficulties associated with positioning and locking the pins and problems of uneven “staircase” surface effects from relying on discrete finite size pins. The main focus of this research is on building a hybrid vacuum-forming machine system (HAVES) based on reconfigurable screw-pin tooling (SPT) as a test bed for understanding the processes involved in developing this technology and to examine the feasibility of implementing such technology in an industrial system. The SPT used is composed of identical screw pins, which are engaged with each other in an array pattern. By adjusting vertical displacement of the screw pins, a wide variety of component geometry can be formed. The adjustment methodology of the SPT is formulated mathematically in order to help construction of the SPT be parametrical thus enabling automatic CNC G-code generation. The HAVES test bed development involves full machine design and hardware and software integration. The hardware integration task included a CNC controller, drive motors, encoders, milling and screw adjustment heads, SPT, vacuum forming system. The software integration task involved the processing of three-dimensional CAD geometry to automatically generate post processed G codes in order to adjust the screw-pin to the required component geometry and subsequent surface machining for driving the final die geometry and minimize operator intervention.
    [Show full text]
  • (12) United States Patent (10) Patent No.: US 9,005,730 B2 Patel Et Al
    US00900573OB2 (12) United States Patent (10) Patent No.: US 9,005,730 B2 Patel et al. (45) Date of Patent: Apr. 14, 2015 (54) AIRCRAFT INTERIOR PANELS AND (56) References Cited METHODS OF PANEL FABRICATION U.S. PATENT DOCUMENTS (75) Inventors: Jayant Dahyabhai Patel, Lake Forest, 4,038.447 A * 7/1977 Brock ............................. 428,72 CA (US); John N. Harris, Seattle, WA 5,000,805 A 3, 1991 Lowe (US); Sergio H. Sanchez, Renton, WA 5.431,990 A 7/1995 Haynes et al. (US); James A. Fullerton, Bothell, WA 5,788, 184 A 8/1998 Eddy 5,839,847 A 11, 1998 Patel (US) 6,000,435 A 12/1999 Patel et al. 6,712.316 B2 3/2004 Jones (73) Assignee: The Boeing Company, Chicago, IL 6,811,192 B2 11/2004 Patel et al. (US) 6,828,001 B2 * 12/2004 Tokonabe et al. ............... 428,69 6,830,076 B1 12/2004 Patel 7,118,069 B2 10/2006 Novak et al. (*) Notice: Subject to any disclaimer, the term of this 7,157,034 B2 1/2007 Bristow et al. patent is extended or adjusted under 35 7,371,451 B2 5/2008 Messinger U.S.C. 154(b) by 565 days. (Continued) OTHER PUBLICATIONS (21) Appl. No.: 13/295,481 Patel, “Self-Configurating Hybrid Duct System & Attachment Tech (22) Filed: Nov. 14, 2011 nologies for Environmental Control System.” SAE Int'l J. of Aero space, vol. 2, No. 1, 275-283 (Mar. 2010). (65) Prior Publication Data Primary Examiner – Brent O'Hern US 2013/0122244 A1 May 16, 2013 (74) Attorney, Agent, or Firm — Ostrager Chong Flaherty & Broitman P.C.
    [Show full text]
  • Intelligent Plastics, Naturally
    Intelligent plastics, naturally Intelligent plastics, naturally Our mission is to produce bioplastics that can challenge the dominance of oil-based polymers, and ultimately replace them completely. Contents 02 Bioplastics 04 Applications 06 Products 08 R&D 10 Company 12 Contact Biome Bioplastics 01 Bioplastics The evolution of polymers From their inception over 100 years ago, plastics have become What is a bioplastic? Why bioplastics? indispensable to our daily lives. A more sustainable product In 1907 Leo Baekeland added phenol to formaldehyde to form Bakelite. Leo became a very wealthy man and the Bioplastics reduce the use of non-renewable, oil-based world became a very different place. Today, plastics are resources, which are increasingly scarce and unstable in price. indispensable at every stage of the supply chain, for every industry, product or service. Managed end-of-life However, whilst plastics are prized for their durability, Bioplastics can biodegrade or compost at the end of their light weight and long life, it is these very factors that useful life. Durable plant-based bioplastics can also be make them one of the larger environmental threats of recycled as well as their conventional equivalents. the modern world. Apart from the small amount that’s incinerated, every bit of plastic made over the last century is still present somewhere on our planet. The price of this Consumer engagement Consumers are increasingly seeking more environmentally ‘miracle material’ is being paid by the natural world: from A bioplastic is a plastic that is made the sea life that consumes it, to hormonal disruption in friendly products, and looking to brands to demonstrate their animals, to the area of ocean dominated by the Great partly or wholly from materials sustainability credentials.
    [Show full text]