WARNING: Unplug the scroll saw 4. Thread the blade attached to the Lower Blade Clamp The Fixture Block For using Plain End Blades: Plain End Blade 8-32 x 7/8″ makes it easier to ® before installation! (Not for use on Model No. 113.236180) through the underside of the table opening. The Lower or M4 x 1″ To use with Pin End Blades Screw with OLSON AC49610 Blade Clamp does not need to be in a fixed position yet. Conversion screw 9/64″ lock washer Plastic Spacer tighten and loosen Use your scroll saw owner’s manual as a guide in The clamps are designed to hold all plain end blades (skip, Hex Wrench ONLY: a blade in the lower Installing the Scroll Saw Blade 5. Next, attach the top plain end of M4 lock tighten Fixture addition to these instructions to install the Scroll Saw reverse, spiral tooth, etc). Upper washer M4x12mm screw & To use Pin End Blades, the Upper blade clamp. the blade to the upper blade clamp. Blade M4 lock washer with Block ONLY for plain Holder Conversion Kit Blade Holder Conversion Kit on your saw. Plain End Blade Alignment and Installation Plastic Spacer Blade Clamp must be re-assembled Place the plastic spacer behind the Clamp 9/64″ end blades. 1. Lay the Lower Blade Clamp Fixture and from its original configuration. Upper WARNING: Unplug the scroll saw before installation! Block with upper clamps as shown in the blade Upper Hex Blade Saw Table #12 x 24 into the fixture block flat side Upper Blade Clamp Upper Blade Clamp Hex Surface Lower drawing. Loosen the screw on the Saw There is NO NEED to Wrench Upper Blade Clamp Plain End Blades offer more and thinner tooth styles. wrench hex nuts down, with the screw facing up Blade mounts on the upper Upper Blade Clamp, insert and tighten Arm Upper Blade re-assemble this part if you Clamp with This Conversion Kit lets you use them on a saw built for Lower and with the pointed end toward Clamp Clamp – saw arm – allowing a Blade and the blade end into the clamp with the want to use plain end blades! Upper Saw Spacer Pin End blades. Check the list below. the slot. exploded view saw built for pin end Clamp blade 3mm hex wrench. Upper Blade 1. Using the 3 mm hex wrench, Arm blades to use plain The Scroll Saw Blade Holder Conversion Kit 2. Place a plain end blade in the Slot end blades. Lower Clamp with Plain End remove the screw to take the slot with the teeth pointing down. 6. Place the Lower Blade Clamp is designed for use on these 16″ scroll saws: BladeBlade Blade hex wrench Scroll Saw Blade Note: Reverse tooth blades will have the lower reverse holding the other end of the blade with teeth upper blade clamp apart. Pin End Clamp in Clamp set for Clamp set Sears Models Northern Hydraulics Record SS-16V Fixture Block #12-24 x 1″ on top of the rubber bumper on the pointing down Plain End for Pin End screws teeth pointing up - away from the lower blade clamp. Chrome 2. Turn the clamp over so Blade Pin End Scroll The Chrome Bracket 23611 and 23612 Model SS16 Shop Fox Chrome Bracket so that the clamp’s Bracket Lower Blades Blades Assembly with Lower Upper Arm Blade Clamp Installation that the wide slot to hold the Conversion Saw Blade with Model AMT Models W1713-16 For Plain End Blades: pointed end fits in the slotted end of with Saw 3mm Hex Blade Clamp mounts 1. Remove the screw, lock washer and the upper blade blade Arm Wrench blade pins is at the bottom, teeth pointing SC 160 4601 and 4602 Scheppach Models The Fixture Block makes it easier to tighten and loosen on the lower saw arm the Chrome Bracket and tighten the facing the you. Fix each clamp half onto the center pin. down Models Reliant Models SD1600, 240VS a blade in the lower blade clamp. You can attach the holder from the upper arm of your saw with the 9/64″ hex to hold plain end blades. screw with the 3mm hex wrench. Reinsert the screw with lock washer and fasten the 1671 and 1695 DD66 and DD67 Deco 405 88002123 Fixture to the edge of your scroll saw or work bench. wrench provided. Save these parts for future use. Chrome 7. Remove the plastic spacer on the Bracket Lower Blade clamp together. Lower Saw Chrome Skill Model HAFCO B-18V Rikon Model If you attach it to the scroll saw, be sure it does not 2. Attach the Upper Blade Clamp using the screw and with Clamp – 10-600VS upper clamp and save it for future use. Proper exploded view Lower Arm Blade Clamp Installation Arm Bracket 3330-3335 TH-405E stick up higher than the saw’s table surface or it can lock washer. Use the screw that best fits your saw and the rubber Assembly Central Machinery Grizzly Go536 interfere with your use of the saw. kit’s blade clamp. 8. Adjust the saw’s tension knob set-up for bumper The Chrome Bracket will hold the blade pins. Rubber Lower 9/64″ Proxxon Micromot VS-16” reverse Models S 5909, DSH-2 as required. #8 toothed lock washer and Pin End Blades do not use the Lower Blade Clamp. Bumper Blade Clamp Hex 1. Hold the fixture against the flat edge on the left or Lower Arm Blade Clamp Installation tooth blade: 62519, 93012 Wen 3920-3921 1. Remove the screw, toothed lock washer and the To Make Internal Cuts with Plain End 8-32 x 3/8″ screw Chrome Wrench right side of the table (use a “C” clamp if available). Mark most of the 1. Loosen tension by turning knob at rear of saw. and the hole location with center punch, small drill, lower blade holder from the lower arm with the Blades: Unclamp the upper blade end and teeth will Exploded Chrome Bracket If your saw is not on this list, it may not fit your saw. 2. Attach the upper pin end of the blade into the slot Bracket 3 mm or other tool. 9/64″ hex wrench. pull it through the workpiece and table face down view Hex This kit may also: be modified for other saws or adapt and with pins aligned in the upper blade clamp. The attached with 2. Slide the rubber bumper onto the Chrome opening. Reinsert the blade through the and a few at Lower Screws and Hex Nuts for Wrench saws that use Plain End Blades to use Pin End Blades, 2. Using a 7/32″ drill, carefully drill the two holes lower pin end of the blade should go through the Screw and table and pre-drilled hole (3/32″dia.) in the the bottom Blade Clamp attaching Fixture Block although this is less common. through the flange of table with light pressure. Bracket. Attach the Chrome Bracket to the will face up. table opening. Toothed lower arm using the screw and toothed lock workpiece and re-install the blade. with hex wrench Lock Socket Head Screws & Lock Washer for attaching 3. Place the #12-24 x 1″ screws through the holes, Upper Blade Clamp (use the screw that fits your saw) Olson Saw Co. 16 Stony Hill Rd., Bethel, CT 06801 washer on the inside surface of the bracket. 3. Fit the bottom pin end of the blade into the slot Washer attach the Fixture and tighten with #12 x 24 hex nuts. For detailed Parts Lists, Video, etc: Chrome with the pins held by the Chrome Bracket. 3. Turn the knob at the rear of your saw to Bracket Socket Head Screw and Toothed Lock Washer for For detailed Parts Lists, Video, etc: If you mount the fixture to a wooden work bench, you https://www.olsonsaw.net/resources/ 4. Adjust the saw’s tension knob as required. attaching Chrome Bracket https://www.olsonsaw.net/resources/ need to supply wood screws to attach it to the edge. loosen the tension of the saw. with rubber bumper Extra Socket Head Screw for Blade Clamps PKF-OL1050 6/20 Printed in USA WARNING: Unplug the scroll saw 4. Thread the blade attached to the Lower Blade Clamp For using Plain End Blades: Plain End Blade 8-32 x 7/8″ WARNING: Unplug the scroll saw For using Plain End Blades: 4. Threadbefore the installation! blade attached to the Lower Blade Clamp (Not for use on Craftsman Model No.8-32 113.236180) x 7/8″ through the underside of the table opening. The Lower or M4 x 1″ Plain End Blade The Fixture Block Blade Clamp does not need to be in a fixed position yet. Conversion screw 9/64″ before installation! (Not for use on Craftsman Model No. 113.236180) through the underside of the table opening. The Lower makesor M4 x it 1 ″easier to ® Screw withUse your scroll saw owner’s manual as a guide in TheConversion clamps are designed to holdscrew all plain end blades9/64 (skip, AC49610 Hex Wrench To use with Pin End Blades Blade Clamp does not need to be in a fixed position yet. tighten and loosen ″ OLSON5. Next, attach the top plain end of M4 lock Use your scroll saw owner’s manual as a guide in The clamps are designed to hold all plain end blades (skip, lock washeraddition to these instructionsPlastic to install Spacer the Scroll Saw reverse, spiral tooth, etc). Hex Wrench Upper washer M4x12mm screw & ONLY: 5. Next, attach the top plain end of aM4 blade lock in the lower Installingthe blade the to theScroll upper blade Saw clamp. Blade Blade M4 lock washer addition to these instructions to install the Scroll Saw reverse, spiral tooth, etc). tighten Blade Holder Conversion Kit on your saw. Upper Fixture Plain End Blade Alignment andbladewasher Installationclamp. M4x12mm screw & Plastic Spacer To use Pin End Blades, the Upper Blade Clamp withthe blade to the upper blade clamp. Block ONLY for plain M4 lockFixture washer Holder Place Conversion the plastic spacer Kit behind the and Blade Holder Conversion Kit on your saw. PlainBlade End Clamp Blade must Alignment be re-assembled and Installation Clamp 1. Lay the Lower Blade Clamp Plastic Spacer Fixture 9/64Place″ the plastic spacerSaw behind Table the end blades. Block with upper clamps as shown in the blade Upper 1. Layfrom the its Lower original Blade configuration. Clamp Hex #12 x 24 and Upper into the fixture block flat side Lower WARNING: Unplug the scroll saw before installation! Saw Saw Table Block with Hexupper clamps as shownSurface in the hex nuts blade Blade down, with the screw facing up Upper drawing. Loosen the screw on the Hex #12 x 24 into the fixture block flat side Upper Blade ClampLower wrench UpperSaw Blade Clamp Blade Arm Upper Blade Surface hex nuts There is NO NEED to Wrenchdrawing. Lower Loosen the screw on the Upper Blade Clamp and with the pointed end toward Clamp Plain End BladesUpper Blade offer moreClamp, and insert thinner and toothtighten styles. wrench down, with the screw facing up Blade with mountsArm on the upper Upper Blade Clamp – Lower re-assemble this part if you UpperBlade Blade Clamp, insert and tightenClamp saw arm – allowing a and This Conversionthe blade Kit letsend youinto usethe themclamp on with a saw the built for exploded view and with the pointed end toward Clamp Clamp Spacer the slot. Clamp – Blade want to use plain end blades! and Upperthe Saw blade end into the clamp with the saw built for pin end blade Pin End blades.3mm Checkhex wrench. the list below. Upper Blade the slot. 2. Place a plain end blade in the exploded view Clamp 1. Using the 3 mm hex wrench, blade Arm blades to use plain Clamp with Plain End 3mm hex wrench. Slot slot with the teeth pointingUpper Blade down. The Scroll6. PlaceSaw the Blade Lower Holder Blade Clamp Conversion Kit Lower 2. Place a plain end blade in the Blade end blades. hex wrench Scroll Saw Blade remove the screw to take the Blade Lower Clamp with Plain End is designedholding for theuse other on theseend of the16 ″blade scroll saws: Blade slot with the teeth pointing down. 6. Place the Lower Blade Clamp Note: Reverse tooth blades will have the lower reverse Clamp in with teeth BladeBlade upper blade clamp apart. Pin End #12-24 x 1Blade″ hex wrench Scroll Saw Blade Note: Reverse tooth blades will haveClamp the setlower for reverseClamp set holding theFixture other Blockend of the blade teeth pointing up - away from the lower blade clamp.with teeth Sears Modelson top of Northernthe rubber Hydraulics bumper onRecord the SS-16V Chrome pointing down Plain End for Pin End screws Clamp in Fixture Block #12-24 x 1″ teeth2. pointingTurn the upclamp - away over from so the lower blade clamp. on topBlade of the rubber bumper on the Pin End Scroll The Chrome Bracketpointing down 23611 and 23612Chrome BracketModel SS16 so that the clamp’sShop Fox Bracket Lower screws Blades Blades Chrome Upper Arm Blade Clamp InstallationAssembly with Lower Saw that the wide slot to hold the ChromeForConversion Plain Bracket End so Blades: that the clamp’s Saw Blade with Bracket Lower Ryobi Model pointed endAMT fits Models in the slottedW1713-16 end of with 3mm Hex Upper Arm Blade Clamp Installation 1. Remove the screw, lock washerBlade and Clamp the mountsupper blade blade Arm Wrench For Plain End Blades: blade pins is at the bottom, The Fixture Block makes it easierteeth to pointingtighten and loosenwith Saw 3mm Hex SC 160 4601 and 4602 Scheppach Models pointed end fits in the slotted end of holder from the upper arm of youron the saw lower with saw the arm 9/64 ″ hex the Chrome Bracket and tighten the The Fixture Block makes it easier to tighten and loosen 1. Removefacing the the you. screw, Fix each lock clampwasher half and onto the the upper center blade pin. a blade in the lower blade clamp.down You can attach the blade Arm Wrench Dremel Models Reliant Models SD1600, 240VS the Chrome Bracket and tighten the wrench provided. Save these partsto hold for plain future end blades.use. screw with the 3mm hex wrench. a blade in the lower blade clamp. You can attach the holderReinsert from thethe screwupper witharm lockof your washer saw and with fasten the 9/64 the ″ hex Fixture to the edge of your scroll saw or work bench. 1671 and 1695 DD66 and DD67 Deco 405 88002123 Chrome screw with the 3mm hex wrench. Bracket Lower Blade wrenchclamp provided. together. Save these parts for future use. 2. Attach the Upper Blade ClampChrome using the screw and Skill Model 7. RemoveHAFCO the plasticB-18V spacer Rikonon the Model Fixture to the edge of your scroll saw or work bench. Lower SawIf you attach it to the scroll saw, be sure it does not Chrome Lower Blade with Clamp – Arm7. Remove the plastic spacer on the Bracket lock washer. Use the screw that Bracketbest fits your saw and the3330-3335 upper clamp and save it for future10-600VS use. Proper exploded view If you attach it to the scroll saw, be sure it does not 2. AttachLower theArm Upper Blade Blade Clamp Clamp Installation using the screw and stick up higher than the saw’s table surface or it can with Clamp – Einhell TH-405E rubber upper clamp and save it for future use. Assembly Central Machinery Grizzly Go536 set-up for stick up higher than the saw’s table surface or it can lockThe washer. Chrome Use Bracket the screw will holdthat bestthe blade fits pins.your saw and the interfere with your use of the saw. Proper kit’s blade clamp. rubber exploded view 8. Adjust Proxxonthe saw’s Micromot tension knob bumper set-up for Rubber Lower 9/64″ Models S 5909, VS-16” reverse interfere with your use of the saw. kit’s blade clamp. 8. Adjust the saw’s tension knob Lower ArmBumper Blade ClampBlade ClampInstallationbumper Hex as required.DSH-2 #8 toothed lock washer and Pin End Blades do not use the Lower Blade Clamp. 1. Hold the fixture against the flat edge on thereverse left or 62519, 93012 Wen 3920-3921 tooth blade: as required. Chrome Wrench 8-32 x 3/8″ screw 1. Hold the fixture against the flat edge on the left or Lower1. Loosen Arm Blade tension Clamp by turning Installation knob at rear of saw. right side of the table (use a “C” clamp if available).tooth blade: Mark 1. Remove the screw, toothed lock#8 toothed washer lock andwasher the and To Make Internal Cuts with Plain End most of the Bracket 8-32 x 3/8″and screw If your saw is not on this list, it may not fit your saw. Exploded right side of the table (use a “C” clamp if available). Mark 1. Remove the screw, toothed lock washer and the ChromeTo Makethe hole Internal location Cuts with with center Plain punch, End small drill,most of the lower blade holder from the lower arm with the Blades: Unclamp the upper blade end and teeth will 2. Attach the upper pin end of the blade into the slot 3 mm lower blade holder from the lower arm with the BracketBlades:or other Unclamp tool. the upper blade end and 9/64″ hex wrench. Exploded pull it through the workpiece and table face down view the hole location with center punch, small drill, and with pins aligned in the upper blade clamp. The teeth will Hex This kit may also: be modified for other saws or adapt attached with face down Wrench view opening. Reinsert the blade through the and a few at or other tool. 9/64lower″ hex pin wrench. end of the blade should go through the Screwpull and2. it throughUsing a the7/32 workpiece″ drill, carefully and table drill the two holes 2. Slide theScrews rubber and Hexbumper Nuts for onto the Chrome saws that use Plain End Blades to use Pin End Blades, Lower opening. Reinsert the blade through the and a few at attaching Fixture Block although thistable is andless pre-drilledcommon. hole (3/32″dia.) in the the bottom Blade Clamp 2. Using a 7/32″ drill, carefully drill the two holes 2. Slidetable theopening. rubber bumper onto the Chrome Toothedthrough the flange of table with light pressure. Bracket. Attach the ChromeLower Bracket to the will face up. Locktable and pre-drilled hole (3/32″dia.) in the the bottom lower armSocket using Head the Screws Bladescrew Clamp& andLock toothedWasher for lock attaching workpiece and re-install the blade. with hex wrench through the flange of table with light pressure. Bracket.3. Fit Attachthe bottom the Chrome pin end ofBracket the blade to the into the slot 3. Place the #12-24 x 1″ screws through the willholes, face up. Upper Blade Clamp (use the screw that fits your saw) Olson Saw Co. 16 Stony Hill Rd., Bethel, CT 06801 lower arm using the screw and toothed lock Washerworkpiece and re-install the blade. washer on the insidewith surface hex wrench of the bracket. 3. Place the #12-24 x 1″ screws through the holes, with the pins held by the Chrome Bracket. attach the Fixture and tighten with #12 x 24 hex nuts. Socket Head Screw and Toothed Lock Washer for For detailed Parts Lists, Video, etc: Chrome washer on the inside surface of the bracket. For detailed Parts Lists, Video, etc: attach the Fixture and tighten with #12 x 24 hex nuts. 4. Adjust the saw’s tension knob as required. If you mount the fixture to a wooden work bench, you 3. ChromeTurn the attaching knob Chromeat the rearBracket of your saw to https://www.olsonsaw.net/resources/ Bracket For detailed Parts Lists, Video, etc: https://www.olsonsaw.net/resources/ with rubber bumper If you mount the fixture to a wooden work bench, you 3. Turn the knob at the rear of your saw to need to supply wood screws to attach it to the edge. loosenBracket the Extra tension Socket ofHead the Screw saw. for Blade Clamps https://www.olsonsaw.net/resources/ with rubber bumper PKF-OL1050 6/20 Printed in USA need to supply wood screws to attach it to the edge. loosen the tension of the saw.