HAND TOOLS HI-LINE UTILITY SUPPLY CO. 28 Phone: 800-323-6606 Fax: 847-488-1285 www.hilineco.com

All insulated tools shown on this 9 PC INSULATED TOOL SET page are rated for exposure up to Cat. No. TR-9ELK 1,000VAC and are dielectrically tested Basic Electrician's Insulated Tool Set at 10,000VAC.

These tools meet or exceed current ASTM F1505-01 and IEC 900 Standards for Insulated hand Tools.

These tools will help you to be compliant with NFPA 70E Standard and OSHA Safety Related Work Practices.

30 PC INSULATED TOOL SET 60 PC INSULATED TOOL SET Cat. No. ITS-MB430 Cat. No. ITS-60B/T This Deluxe Maintenance This 60 pc Insulated Tool Set Insulated Tool Set comes in a comes in a tool box. padded storage case. Ratchet is 3/8" drive; 30-150 in/lb. torque ; 8pc 3/8" - 13/16" deep well sockets and more. Hand Tools

WARNING: These tools are to be used as secondary protection and are not intended to be used in place of other personal protective equipment. Whenever possible, always de-energize lines before working on or around them. Although the insulation on these tools is impact resistant and flame retardant, each tool should be inspected prior to each use for cracks, cuts or other damage. Should the yellow insulation become visible through the orange outer layer, discontinue use immediately. HAND TOOLS HI-LINE UTILITY SUPPLY CO. Phone: 800-323-6606 Fax: 847-488-1285 www.hilineco.com 29

TWISTOOL Inside grooves for DEMOLITION DRIVER Area for Ring Bolt Wire Capping Tightening Staple Holding Cat No. 602-7DD Save your other tools from the abuse these are designed to take. Unique Wire Holding groove design transfers impact force for Spreading directly to the work surface. Cat No. HLTT • 7” Driver with 5/16” Keystone This Insulated puts extra distance between you • Engineered and tested for prying and chiseling and conductive equipment. It is a spreading, tightening, • Metal strike cap protects handle from blows and wire-capping tool, and can be conveniently hooked on a lanyard. It's also a safer alternative to a screwdriver when ROUND SHANK, SPECIAL hammering staples. Meets ASTM 1505 Standards. PROFILATED PHILLIPS TIP

HEAVY-DUTY SQUARE-SHANK, KEYSTONE-TIP Catalog Point Shank Overall Number Size Length Length 603-1 #2 1-1/2" 3-7/16" Designed for the most demanding uses. With heavy 603-3 #1 3" 6-3/4" duty square shank for wrench-assisted turning. 603-4 #2 4" 8-5/16" 603-6 #3 6" 11" Catalog Tip Width x Overall Number Shank Length Length 600-1 7/32" X 1-1/2" 3-7/16" HOLLOW SHAFT NUT DRIVERS 600-4 1/4" X 4" 8-11/32" 600-6 5/16" X 6" 10-15/16" 600-8 3/8" X 8" 13-7/16" Handle caps are color-coded for easy size 600-12 1/2" X 12" 17-7/16" identification. Full hollow shaft chrome plated shank permits turning nuts on long screws. HEAVY-DUTY ROUND-SHANK, Also available with magnetic tips. KEYSTONE-TIP Catalog Color Hex Shank Hand Tools Number Code Size Length * 630-03 Black 3/16" 3" Built to handle the tough jobs with ease. * 630-04 Red 1/4" 3" * 630-05 Yellow 5/16" 3" Catalog Tip Width x Overall Number Shank Length Length * 630-055 Green 11/32" 3" 602-3 7/32" X 3" 6-3/4" * 630-06 Blue 3/8" 3" 602-4 1/4" X 4" 8-11/32" * 630-07 Brown 7/16" 3" * 630-08 Red 1/2" 3" 602-6 5/16" X 6" 10-15/16" 630-09 Orange 9/16" 4" 602-8 3/8" X 8" 13-7/16' 630-10 Yellow 5/8" 4" 602-10 3/8" X 10" 15-7/16" * 631 7-pc Set, 3/16" - 1/2" 602-12 3/8" X 12" 17-7/16" with plastic roll-up HAND TOOLS HI-LINE UTILITY SUPPLY CO. 30 Phone: 800-323-6606 Fax: 847-488-1285 www.hilineco.com

FOLDING SETS HACKSAW FRAMES

Cat. No. Description 70581 Eight-Key Set; 3" long w/ 1-7/16" - 2-3/8" Keys Sizes: .05, 1/16, 5/64, 3/32, 7/64, 1/8, 9/64, 5/32 Cat. No. Description 70591 Nine-Key Set; 4.25" long w/ 1-5/8" - 3-1/2" Keys Size: 5/64, 3/32, 7/64, 1/8, 9/64, 5/32, 3/16, 7/32, 1/4 701-S Tubular Hacksaw Frame w/ Plastic Grip Inserts

1200BI-P 12"-Tri-Cut, Bi-Metal Hacksaw Blade - Unique 70579 Five-Key Set; 5-1/4" long w/ 3-1/8" - 4-5/8" Keys design provides 32T, 24T, & 18T on one blade Sizes: 3/16, 7/32, 1/4, 5/16, 3/8

HAMMERS FILES

2 4 6

1 3 5

Cat. No. Description Bastard 2nd Cut Smooth 10" Flat File 03665 03698 03731 12" Flat File 03764 03797 03830 Ref Cat. No. Description 14" Half Round File 05194 05225 05258 803-12 12 oz Ball Peen Hammer w/ Hickory Handle 10" Mill File 08642 08673 08704 803-16 16 oz Ball Peen Hammer w/ Hickory Handle 12" Mill File 08737 08768 08799 1 803-24 24 oz Ball Peen Hammer w/ Hickory Handle 803-32 32 oz Ball Peen Hammer w/ Hickory Handle

Hand Tools 2 809-36MF 36 oz Milled Face/Smooth Face Hammer POLE 3 808-20 20 oz Straight Claw Hammer w/ Fbrgls Handle 818-16 16 oz Curved Claw Hammer w/ Fbrgls Handle 4 818-20 20 oz Curved Claw Hammer w/ Fbrgls Handle 5 HE-36 36 oz Double Face Hammer w/ Hickory Hndl Cat. No. 66326 For driving bolts through wood poles. Ergonomic 6 832-32 32 oz Straight Claw Hammer w/ Hickory Hndl handle with overstrike protection. 12" punch length with 3/8" diameter. Chamfered tip. HAND TOOLS HAND TOOLS HI-LINE UTILITY SUPPLY CO. Phone: 800-323-6606 Fax: 847-488-1285 www.hilineco.com 31

TAPERED NOSE DIAG CUTTERS HIGH-LEVERAGE SIDE CUTTERS

D202-5 D220-7 Tapered nose and standard bevel cutting knives. One inch jaws reach into confined spaces. Cat No. Description D202-5 Cutter with dipped handles, 5.5" o.a. D202-6 Cutter with dipped handles, 6" o.a. D220-7 HD cutter with dipped handles, 7-5/8: o.a.

LONG NOSE D213-9NE HD213-9NE D2000-9NETH D2000-9NE These high-leverage side cutting pliers are 9-1/4" long. Streamlined nose with knurled jaws. Hold D203-6 threaded end of bolts without damaging threads, clean and straighten threads, and remove or install Standard long nose pliers have knurled jaws. pole hardware easily. 203 series has cutting edges at hinge. "2000" series cutters have ultra-durable cutting Cat No. Description edges for ACSR and other hardened materials: bolts, D203-6 Long nose with cutters, 6-5/8" o.a. nails, & wire. D301-5 Standard long nose plier, 5-5/8" o.a. Cat No. Description D301-6 Standard long nose plier, 6-5/8" o.a. D213-9NE Std plier with blue dipped handles HD213-9NE Same as above with HD org dipped handles HIGH-LEVERAGE DIAG CUTTERS D2000-9NETH Std plier with 5/18-11 thread at hinge Plier with hard cutting edge & blue dipped D2000-9NE handles

D228-8 SLIP JOINT PLIERS High-leverage design with standard bevel cutting edges.

Cat No. Description D228-8 Cutter with red dipped plastic handles, 8" o.a.

D248-8 Same as above with angled head, 8" o.a. Hand Tools Jaws are positioned and locked into place by engaging tongue in proper groove. Series of CABLE CUTTER channels gives wide range of jaw openings. Jaws cannot slip even under heavy pressure. Cat No. Description D502-10 1-3/4" cap., 10" o.a., with yellow dipped handles HD502-10 Same as above with HD orange handles Cat. No. 63050 D502-12 2-1/8" cap, 12" o.a., with yellow dipped handles This economical tool handles most cable cutting jobs with ease. Special high leverage design gives it HD502-12 Same as above with HD orange handles amazing cutting capability for its size. Shear type 430 10" "Channelock" with blue dipped handles jaws cut up to 4/0 Al, 2/0 soft copper, and 100 pair 24 gauge communication cable. 9.5" long. HAND TOOLS HI-LINE UTILITY SUPPLY CO. 32 Phone: 800-323-6606 Fax: 847-488-1285 www.hilineco.com CRIMPER / CUTTER DRAWKNIFE

Cat. No. 1005 BLADE WIDTH 1-5/8" Crimping die marked for insulated and non- BLADE LENGTH 10" insulated solderless terminals and connectors. Cat. No. 600 Accommodates wire from No. 10 to 22 AWG. This drawknife is manufactured from heat Wire cutter in nose. Red plastic dipped handles. treated carbon tool steel for maximum life and oxide finished ­to help protect from rust. Large hardwood RATCHETING BOX handles.

SPLICER'S TOOLS Cat. No. Description 68200 1/4" x 5/16" Ratchet box wrench; 4.25" o.a. 68201 3/8" x 7/16" Ratchet box wrench; 5.5" o.a. 68202 1/2" x 9/16" Ratchet box wrench; 6.5" o.a. 68203 5/8" x 11/16" Ratchet box wrench; 8" o.a. 68204 5/8" x 3/4" Ratchet box wrench; 8" o.a. 68205 11/16" x 3/4" Ratchet box wrench; 9.25" o.a. Splicing tools include cable splicer's knife, 68206 13/16" x 7/8" Ratchet box wrench; 9.25" o.a. electrician's scissors with stripping notches, & leather holder. 68222 Ratchet Box Wrench Set w/ pouch; includes all Cat. No. Description HL514 Electrician's scissors with strip notches (wiss) CAN WRENCH (3/8" X 7/16") HL515 Splicer's knife with SS blade and insulated handle HL414 Leather Pouch

Cat. No. 68005 1-1/4" deep, heat-treated, alloy steel, thin wall SHARPENING TOOL sockets with high-impact handle. Cat. No. 44151

ADJUSTABLE WRENCHES VISE-GRIP TYPE PLIERS

Hand Tools Extra capacity design allows jaws to open 3/16" wider than standard wrenches. Rugged construction, chrome plated. These versatile, rugged, and powerful pliers are a Cat. No. Description must for every tool user. Adjust and lock at any size D507-6 6" adjustable wrench; 15/16" capacity with desired amount of pressure. Nickel-plated finish. D507-8 8" adjustable wrench; 1-18" capacity Cat. No. Description D507-10 10" adjustable wrench; 1-5/16" capacity 10R 10" straight jaw vise grip plier D507-12 12" adjustable wrench; 1-1/2" capacity 10CR 10" curved jaw vise grip plier HAND TOOLS HAND TOOLS HI-LINE UTILITY SUPPLY CO. Phone: 800-323-6606 Fax: 847-488-1285 www.hilineco.com 33

LEATHERMAN MULTI-TOOLS

WAVE OHT SKELETOOL WINGMAN STYLE CS SQUIRT ES4 CRATER Cat. No. 830038 Cat. No. 831540 Cat. No. 830950 Cat. No. 831426 Cat. No. 831207 Cat. No. 831204 Cat. No. 860221

Feature Wave OHT Skeletool Wingman Style Squirt Crater Bit Driver X X Bottle Opener X X X X Can Opener X X X Carabiner X X X Combo Knife X X File X X X Hard Wire Cutters X X Knife X X X X X Nail File X Needlenose Pliers X X* X X* X* Oxygen Tank Wrench X Package Opener X Pliers X X* X X* Ruler X X Saw X X Screwdriver X X X X X Screwdriver X X (Flat/Phillips) Screwdriver, Phillips X X X Serrated Knife X X Scissors X X X X Strap Cutter X Threaded X Hand Tools X Wire Cutters X X* X X* X* Wire Stripper X X* X X* *Spring Action

ACCESSORIES Cat. No. Description 931014 Bit Kit - 21 steel bits that fit into all tools with a Bit Driver 931009 3.25" Bit Driver Extender 880046 880046 13 Lumen Flashlight, Powered by (1) AAA

931014 931009 HAND TOOLS HI-LINE UTILITY SUPPLY CO. 34 Phone: 800-323-6606 Fax: 847-488-1285 www.hilineco.com

LINEMAN'S SKINNING KNIVES LINEMAN DRAWKNIFE

Cat. No. HL2055-R Cat. No. HL2056 The Lineman Drawknife easily removes insulation and semi-con from all types of cable. It's contoured blade and unique stripping edge safely "shaves" Cat. No. HL2055 insulation or semi-con from a wide range of cable sizes without damaging the conductor. Saves time, These 9" skinning knives have an ergo-engineered, reduces potential for elbow injuries and is safer than soft-grip textured handle designed with finger stops a skinning knife. Works on all types of cable. for maximum leverage and added safety. Ring fits over bucket hooks. Not designed for use in shot guns. The extra heavy duty .074” chrome vanadium steel BRUSH BLADE blade has a 5° offset angle and a scraping notch.

Two tools in one: wire brush for cleaning up to 1000MCM conductor and a blunt tip knife blade that locks in open position and can be closed when not in use. Cat. No. Description 1570-3 7086-1 M4455-50 HLBB-1 Brush Blade Cat. No. Description Ring HLWB-1 Replacement Wire Brush 1570-3 8" Skinning Knife with flat handle Yes 7086-1 9" Skinning Knife with round ribbed handle No LOCK BACK KNIVES 7086 9" Skinning Knife with round ribbed handle Yes M4455-50 Skinning Knife for use with Hot Stick No

44005 ERGONOMIC SKINNING KNIFE • Premium quality 2-5/8" stainless blade. • Impact-resistant nylon resin handle with rubber insert. • Reversible thumb stud for one-handed opening. Cat. No. 7091 Cat. No. Description With a textured rubber handle, this knife fits comfort- 44005 Lockback Knife ably in a gloved hand. The Round handle allows the 44005R Lockback Knife (rounded tip)

Hand Tools user to create the proper cutting angle by rotating the knife within the hand instead of repetitively turning the wrist. 5 ¾" long handle.

LINEMAN KNIFE POUCH Cat. No. 5163 Cat. No. 44006 Leather skinning knife pouch • Premium quality 2-5/8" stainless blade. • Slim silver anodized aluminum handle. • Reversible thumb stud for one-handed opening. • Includes removable belt clip. HAND TOOLS HAND TOOLS HI-LINE UTILITY SUPPLY CO. Phone: 800-323-6606 Fax: 847-488-1285 www.hilineco.com 35

5-IN-1 LINEMAN'S WRENCH ISOLATED RATCHET WRENCH

This wrench features 3/4” and 1”x1- 1/8” combination square socket for most Cat. No. HL34916 common utility hardware plus 9/16” and • Mechanic's grade isolated wrench that will hold up to lineman use. 3/4” wrench sizes. • This 9/16"- 3/4" combination wrench features heavy duty ratchet wrench heads isolated from Cat. No. Description each other by a molded handle. KT155T 5-in-1 Wrench, 9.5" long KT155HD 5-in-1 Heavy Duty Wrench, 12.25" long

INSULATED WRENCHES

Cat. No. Side 1 Style Side 2 Style Style 1 Style 9 Style 5 Style 11 BW-244 1/2" & 9/16" 1 5/8" x 3/4" 1 (4 in 1) Ratchet Ratchet Style 7 BW-223 9/16" Ratchet 1 3/4" Ratchet 1 BW-223HD 9/16" Heavy 1 3/4" Heavy 1 Duty Ratchet Duty Ratchet Style 6 BW-2212 1/2” Ratchet 1 9/16” Ratchet 1 BW-2234 1/2” Ratchet 1 5/8” Ratchet 1 BW-2236 5/8” Ratchet 1 13/16” Ratchet 1 BW-2237 5/8” Ratchet 1 3/4” Ratchet 1 BW-2233 5/8” Ratchet 1 9/16” Ratchet 1 BW-2242 11/16” Ratchet 1 15/16” Ratchet 1 Style 4 Style 17 BW-2245 7/8" Ratchet 1 15/16" Ratchet 1 BW-2238 3/4” Ratchet 1 13/16” Ratchet 1 BW-224 3/4” Ratchet 1 7/8” Ratchet 1

These wrenches have handles formulated of a Hand Tools BW-203 9/16” Ratchet 1 3/4” Ratchet 1 high strength and high dielectric polymer. The No Insulation No Insulation handle features: BW-2093 5/16” Allen 4 Eye Loop 9 • See through port in the center of the handle to BW-240P1 3/8" Rev. Allen 5 Penta Socket 6 confirm that the two ends are not electrically connected. BW-240 5/16” Rev. Allen 5 3/8” Rev. Allen 5 • Superior tool metal-to-metal electrical BW-241P 5/16" Rev. Allen 5 Penta Socket 6 insulation BW-251 5/16” Rev. Allen 17 90° Rev. Penta 11 • Indicator Ribs for improved safety BW-241S 5/16” Rev. Allen 5 Eye Loop 9 BW-2091P Penta Socket 6 Eye Loop 9 BW-2093P90 90° Penta 7 5/16” Allen 4 OTHER SIZES AND COMBINATIONS AVAILABLE HAND TOOLS HI-LINE UTILITY SUPPLY CO. 36 Phone: 800-323-6606 Fax: 847-488-1285 www.hilineco.com

GOAT WRENCH RATCHETING SPUD WRENCH

Cat. No. 920 Cat. No. 3238 Wrench has three thread chasers in handle: Ratcheting spud wrench accepts 1/2" drive sockets. 5/8-11NC, 1/2-13NC, 3/8-16NC ADJUSTABLE SPUD WRENCH LINEMAN'S WRENCHES

Cat. No. 3239 3146 Adjustable spud wrench fits nuts up to 1-1/2"

WRENCH HOLDERS 3146B Each end has two different size openings. Hole at large end is used for turning in standard pole steps. Wrench not Cat No Large End Small End included 3146 29/32" & 1-3/32" 5/8" & 13/16" 3146A 1-1/16" & 1-5/16" 5/8" & 7/8" 3146B 1-1/16" & 1-3/16" 11/16" & 7/8" Cat. No. 5460 Cat. No. 6102 OFFSET SPUD WRENCHES BULL & DRIFT PINS

Extra-heavy-duty head area gives maximum strength and durability. Handle features an extra-deep offset to provide additional hand-clearance without sacrificing tightening power. Continuous taper of handle makes Cat No Description Max Dia Point Length lining-up bolt holes easy. 3255 Bull Pin 1-1/4" 5/16" 13" Cat. No. Nut Type Bolt Size Nut Size 3260 Drift Pin 11/16" 5/16" 7.5" 3210 U.S. Heavy 1/2" 7/8" 3261 Drift Pin 13/16" 7/16" 8" 3211 U.S. Heavy 5/8" 1-1/16" 3262 Drift Pin 15/16" 1/2" 8" 3212 U.S. Heavy 3/4" 1-1/4" 3263 Drift Pin 1-1/16" 9/16" 8" 3213 U.S. Heavy 7/8" 1-7/16" Hand Tools 3214 U.S. Heavy 1" 1-5/8" 3220 U.S. Regular 1/2" 13/16" STRIKING BOX WRENCH 3221 U.S. Regular 5/8" 1" Cat. No. 88 3222 U.S. Regular 3/4" 1-1/8" 12 point wrench has 3223 U.S. Regular 7/8" 1-5/16" ample striking face for efficient rotation of large 3224 U.S. Regular 1" 1-1/2" fasteners. Sizes range from 3231 Utility 5/8" 15/16" 1-3/16" to 4-5/8". Please 3232 Utility 3/4" 1-1/16" specify size when ordering. HAND TOOLS HAND TOOLS HI-LINE UTILITY SUPPLY CO. Phone: 800-323-6606 Fax: 847-488-1285 www.hilineco.com 37

NUT RUNNER RATCHET LINEMAN'S WRENCH The 3-in-1 socket on this wrench can handle the three most common fasteners on utility poles: Lag Bolts, "C" Clamps, and Suspension Bolts. "Bolt- Thru" feature allows tool to work on nuts threaded • Distribution and Transmission models available on any length bolt. • Utility specific impact socket is designed to fit Can be ordered with Double Square common sizes of square nuts. or Triple Square socket. Handle comes in cast iron or steel combo with large • Hex quick change adapter is included. reverse lever. Cat. No. Description Distribution Nut Runner & Adapter NR1 Triple Square Socket Double Square Socket (3/4", 13/16", 1", 1-1/8") Replacement Distribution Adapter 49782 (7/16" hex to 3/4" sq) Transmission Nut Runner & Adapter NR2 (1", 1-1/8", & 1-5/16") Replacement Transmission Adapter 21111 FITS: 1" & 1-1/8" NUTS FITS 1" & 1-1/8" NUTS (7/16" hex to 1-1/8" sq) (5/8" & 3/4" BOLTS) AND (5/8" & 3/4" BOLTS) 3/4" NUTS (1/2" BOLTS) 4-IN-1 IMPACT SOCKET

• Fine tuned ball detent provides improved CAT NO. HL151T STEEL HANDLE WITH retention, minimizing drops. TRIPLE SQUARE SOCKET • Hex quick change adapter is included. Cat. No. Description Distribution Impact Socket & Adapter NRHD (3/4", 13/16", 1" & 1-1/8" sq) Replacement Distribution Adapter NRHDA (7/16" hex to 3/4" sq) CAT NO. HL151D Transmission Impact Socket & Adapter STEEL HANDLE WITH NRHD2 DOUBLE SQUARE SOCKET (1-1/8", 1-5/16", 1-1/2" sq) Replacement Transmission Adapter NRHDA2 (7/16" hex to 1-1/8" sq) Hand Tools

TRIPLE SQUARE TOWER WRENCH CAT NO. HL51T CAST IRON HANDLE WITH TRIPLE SQUARE SOCKET

Cat. No. HL104T Bolt-Thru design allows threaded rod to pass through the socket so that nuts can be secured on any threaded length. The triple square socket fits 1-1/8” square nuts (3/4” CAT NO. HL51D CAST IRON HANDLE WITH bolts), 1-5/16” square nuts (7/8” bolts) and 1-1/2” DOUBLE SQUARE SOCKET square nuts (1” bolts). It also fits 1-1/2” hex bolts. HAND TOOLS HI-LINE UTILITY SUPPLY CO. 38 Phone: 800-323-6606 Fax: 847-488-1285 www.hilineco.com

1/2" DRIVE SOCKETS 3/4" DRIVE SOCKETS

6 & 8 Point Impact

6 Pt. Regular Length 6 Pt. Deep Well 6 pt 6 pt & 8 pt Impact Impact REG LENGTH DEEP WELL Size Cat. No. Length Cat. No. Length 6 pt 8 pt Cat. No. Length SIZE Cat. No. Cat. No. Length 3/4" 6824 1-3/4" 6924 4816 1/2" 4916 4776 13/16" 6826 6926 4818 9/16" 4918 4778 7/8" 6828 6928 1-7/8" 4820 5/8" 4920 4780 15/16" 6830 6930

4822 1-1/2" 11/16" 4922 4782 1" 6832 6932 4824 3/4" 4924 4784 3-1/4" 1-1/16" 6834 6934 4826 13/16" 4926 4786 1-1/8" 6836 6936 3-9/16" 4828 7/8" 4928 4788 1-3/16" 6838 6938

4830 15/16" 4930 4790 1-1/4" 6840 2-1/8" 6940 1-3/4" 4832 1" 4932 4792 1-5/16" 6842 6942 4834 1-1/16" 4934 4794 1-3/8" 6844 6944 3-1/2" 4836 1-1/8" 4936 4796 1-7/16" 6846 6946 1-3/4" 4838 1-3/16" 4938 1-1/2" 6848 6948 2-1/4" 4840 1-1/4" 1-5/8" 6852 6952 Cat. No. 6581 - Socket Retainer 8 pt sockets also available 1/2" DRIVE SOCKET KITS PENTA-HEX SOCKETS Our Penta-Hex combination sockets have a Penta-Hex on one end and a 3/4" hex on the other. The center female square drive is designed to Cat. No. Description be used with any 1/2" or 3/8" 407 1/2" drive, 14 pc kit, 6pt deep with rail clips square drive extension. 1/2" drive, 13 pc kit, 8pt deep well, includes

Hand Tools S4579 Cat. No. Description sockets 3/8" - 1-1/8" PHS-1 3/8" sq. drive comb. penta socket PSH-2 1/2" sq. drive comb. penta socket

QUICK CHANGE CHUCK PENTA SOCKET Cat. No. HLQR-514 Cat. No. 9076 1/2" Square drive female 1/2" Drive Penta Socket for use with to 7/16" female quick change chuck. standard ratchet wrenches and impact wrenches. HAND TOOLS HAND TOOLS HI-LINE UTILITY SUPPLY CO. Phone: 800-323-6606 Fax: 847-488-1285 www.hilineco.com 39

ISOLATED EXTENSIONS 1/2” WRENCHES Cat. No. Description 5/16 Allen Head Wrench end with 3/8" sq. ISE-4 dr., 4" long (rating: 1000V, 420 in lb) 6" x 3/8" Sq. Drive Extension, (rating ISE-6 500kV, 600 in lb) 8" x 1/2" Sq. Drive Extension, (rating: ISE-8 5kV, 60 in lb) E TRI PENTA WRENCH

Cat. No. HLDTP1 I This tool combines three everyday functions into one tool: F C H • 3/8" Screwdriver A B G • Hand Hole Lid Lifter • Penta Wrench D Green speed sleeve spins freely to open Cat. No. Description Lgth/Wgt transformers and switch gear 2x faster. 4-33B (A) 7/16 Hex - 1/2 Sqr Impact Adapter 3" / .2 4426 (B) Ratchet, Series 400 Knurled Grip 10.25" / 1.5 POLE STEP REMOVER 4433 (C) Raised Cap Lineman’s Wrench 10.25" / 1.5 4425 (D) Ratchet, Series 400 Knurled Grip 15" / .2 4902 (E) Impact G Adapter; 1/2" F - 3/4" M - / .5 Cat. No. HLPSR-07 - 7/16" Hex Drive Tool Cat. No. HLPSR-10 - 5/8" Hex Drive Tool 6900 (F) Impact G Adapter; 3/4" F - 1/2" M - / .4 4405 (G) 5" Extension 5" / .5 POLE STEP INSTALLER 4478 (H) Micro-Adjustable , 30-250 fp - / 5 9S291 (I) Torque Multi. 1/2"F-3/4" M, 1000 ft./lbs - / 5.9 4905 5" Impact Extension - 1/2" Drive 5" / .5 Cat. No. HLPSI-07 - 7/16" Hex Drive Tool Cat. No. HLPSI-10 - 5/8" Hex Drive Tool 3/4” WRENCHES PIPE WRENCHES C Hand Tools

HEAVY DUTY ALUMINUM Size Capacity Cat. No Wgt Cat No Wgt A B 8" 1" 31005 .75 Cat. No. Description Wgt 10" 1-1/2" 31010 1.75 810 1 6400 24” Ratchet, Series 400, 3/4" Drive 5.3 12" 2" 31015 2.75 6403 3.5" Extension .8 14" 2" 31020 3.5 814 2.3 6901 (A) Adapter, 3/4" F - 1" M, 3/4" Drive .7 18" 2-1/2" 31025 5.75 818 3.6 24" 3" 31030 9.75 824 6 8900 (B) Adapter, 3/4" M - 1" F, 1" Drive 1 36" 5" 31035 19 836 11 6448 3/4" Dr., 100-600 ft lb, Torque Wrench 17 48" 6" 31040 34.25 848 18.5 9S292 (C) Torque Mult. 3/4"F-1"M, 2000 ft/lbs 13.9 HAND TOOLS HI-LINE UTILITY SUPPLY CO. 40 Phone: 800-323-6606 Fax: 847-488-1285 www.hilineco.com

6' FIBERGLASS RULE 50' & 100' FIBERGLASS TAPES Durable, 1/2" wide, plastic Cat. No. 910-6 coated, fiberglass tapes are Inside reading designed to resist stretch and fiberglass rule is extreme weather extremely flexible conditions. and rugged. Lightweight, high impact polystyrene case. 6' WOOD RULE Cat. No. 966 Two Way Cat. No. Description Repl blade wood rule 703 50' Fiberglass Tape in Closed Case R-703 measures both 706 100' Fiberglass Tape in Closed Case R-706 right-to-left and left-to-right. Flat, inside markings lie close FE050 50' Fiberglass Tape in Open Case R-1703 to the work and are marked on both sides. FE100 100' Fiberglass Tape in Open Case R-1706

150' & 200' FIBERGLASS TAPES WIRE MIKE Cat. No. WIREMIKE Lightweight open reels house Designed for 1/2" fiberglass tapes. Open reel measuring ACSR, stranded and solid conductors, design will not collect dirt like I.P.S. tubing, rigid and thinwall conduit, plus inside a closed case. and outside dimensions of tubing and pipe.

MEASURING WHEELS Cat. No. Description Rolling tapes are built to measure up to 100,000' 1707 150' Fiberglass Tape in Open Case under most terrain conditions. Automatic brake FE200 200' Fiberglass Tape in Open Case prevents accidental back-tracking. Built-in stand keeps wheel in upright position. Solid wheel model offers easy movement through brush. 25' TAPE MEASURE Cat. No. PS3425 This is the longest lasting, most durable power tape available. Virtually unbreakable 5 rivet Dura- Life end hook with 10X longer life. 1" wide nylon powder coated blade lasts 5x Hand Tools longer than other heavy duty blades.

623 415 400 TORPEDO LEVEL Cat. No. Description Cat. No. 930-9 400 Measuring Wheel; 15.5" Spoked 623 Measuring Wheel; 23" Spoked 415 Measuring Wheel; 15.5" Solid 400-15 Case for model 400 & 415 HAND TOOLS HAND TOOLS HI-LINE UTILITY SUPPLY CO. Phone: 800-323-6606 Fax: 847-488-1285 www.hilineco.com 41

HAND-HELD LASER DISTANCE METERS Quickly and accurately calculate horizontal, vertical and slope distances with the press of a button. With the revolutionary technology in the these distance meters, you decide exactly how and where you want to shoot. Verify a tree clearance in a matter of seconds with one shot to an encroaching branch and one shot to the wire. • Built in serial port or Bluetooth easily integrates with GPS (Bluetooth featured on select models only) • In-Scope Data Display • 7x power magnification • Adjustable Eye Relief & LCD Focus • Range goes up to 2,000 meters (reflective target) and 1,000 meters (non- reflective) 200 SERIES 360 SERIES Measures Distance, Inclination & Height Measures Distance, Inclination, Height & Azimuth

Cat. No. LT360 Standard model Cat. No. LT200 measures distance, Standard model inclination & measures distance, height. Additionally, inclination, and height. measures azimuth and remote span values using the built-in digital compass.

Cat. No. LT200L Cat. No. LT360B Economy model Same as LT360, in the 200 series but features Bluetooth with a smaller range (up capabilities to 1,750m on a reflective target, 1,000m non- reflective) and 4x power

magnification. Hand Tools

Cat. No. LT200X Same as LT200, Cat. No. LT360R but is built rugged. Same as LT360, Also features Bluetooth but features Bluetooth capabilities and has a capabilities and is premium range (up to built rugged and 2,500m on reflective waterproof. target, 1,900m non- reflective)