LS-2125_brother_cover_Eng K
KNOWING YOUR SEWING MACHINE
SEWING BASICS
UTILITY STITCHES
APPENDIX
Basic Sewing and Mending Machine Operation Manual English XE4592-001 Please visit us at http://solutions.brother.com where you can get product support and answers to frequently Printed in China asked questions (FAQs). LS-2125_brother_cover_Eng_H2-3 K LS2125.book Page 1 Tuesday, February 26, 2008 1:43 PM
“IMPORTANT SAFETY INSTRUCTIONS” When using the sewing machine, basic safety precautions should always be followed, including the following: “Read all instructions before using.”
DANGER – To reduce the risk of electric shock: 1. The sewing machine should never be left unattended when plugged in. Always unplug this sewing machine from the electrical outlet immediately after using and before cleaning. 2. Always unplug before changing the light bulb. Replace bulb with same type rated 15 watts.
WARNING – To reduce the risk of burns, fire, electric shock, or injury to persons: 1. Do not allow this machine to be used as a toy. Close attention is necessary when the sewing machine is used by or near children. 2. Use this sewing machine only for its intended use as described in this manual. Use only accessories recommended by the manufacturer as contained in this manual. 3. Never operate this sewing machine if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the sewing machine to the nearest authorized dealer or service center for examination, repair, electrical or mechanical adjustment. 4. Never operate the sewing machine with any of the air openings blocked. Keep the ventilation openings of the sewing machine and foot controller free from the accumulation of lint, dust and loose cloth. 5. Never drop or insert any object into any openings. 6. Do not use this machine outdoors. 7. Do not operate this machine where aerosol (spray) products are being used or where oxygen is being administered. 8. To disconnect, turn the main switch to the symbol “O” position which represents off, then remove plug from outlet. 9. Do not unplug by pulling on the cord. To unplug, grasp the plug and pull, not the cord. 10. Keep fingers away from all moving parts. Special care is required around the sewing machine needle. 11. Always use the proper needle plate. The wrong plate can cause the needle to break. 12. Do not use a bent needle. 13. Do not pull or push the fabric while stitching. It may deflect the needle causing it to break. 14. Switch the sewing machine to the off, symbol “O” position when making any adjustments in the needle area, such as threading the needle, changing the needle, threading the bobbin, or changing the presser foot. 15. Always unplug the sewing machine from the electrical outlet when removing covers, lubricating, or when making any other user service adjustments mentioned in this instruction manual. 16. This sewing machine is not intended for use by young children or impaired persons without supervision. 17. Young children should be supervised to ensure that they do not play with this sewing machine. “SAVE THESE INSTRUCTIONS” “This sewing machine is intended for household use.”
1 LS2125.book Page 2 Tuesday, February 26, 2008 1:43 PM
FOR USERS IN THE UK, EIRE, MALTA AND CYPRUS ONLY If this machine is fitted with a three-pin non-rewireable BS plug then please read the following. IMPORTANT If the available socket outlet is not suitable for the plug supplied with this equipment, it should be cut off and an appropriate three-pin plug fitted. With alternative plugs an approved fuse must be fitted in the plug.
NOTE The plug served from the main lead must be destroyed as a plug with bared flexible cords is hazardous if engaged in a live socket outlet. In the event of replacing the plug fuse, use a fuse approved by ASTA to BS 1362, i.e. carrying the mark, rating as marked on plug. Always replace the fuse cover, never use plugs with the fuse cover omitted.
WARNING DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS MARKED WITH THE LETTER ‘E’, BY THE EARTH SYMBOL OR COLOURED GREEN OR GREEN AND YELLOW.
The wires in this main lead are coloured in accordance with the following code:
Blue Neutral
Brown Live
As the colours of the wiring in the main lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows.
The wire which is coloured blue must be connected to the terminal which is marked with the letter ‘N’ or coloured black or blue.
The wire which is coloured brown must be connected to the terminal which is marked with the letter ‘L’ or coloured red or brown.
2 LS2125.book Page 3 Tuesday, February 26, 2008 1:43 PM
CONGRATULATIONS ON CHOOSING OUR MACHINE To fully enjoy all the features, we suggest that you study the manual before using the machine. PLEASE READ BEFORE USING THIS MACHINE
For safe operation 1. Be sure to keep your eye on the needle while sewing. Do not touch the handwheel, thread take- up lever, needle, or other moving parts. 2. Remember to turn off the power switch and unplug the cord when: • Operation is completed • Replacing or removing the needle or any other parts • A power failure occurs during use • Maintaining the machine • Leaving the machine unattended 3. Do not store anything on the foot controller. 4. Plug the machine directly into the wall. Do not use extension cords.
For a longer service life 1. When storing this machine, avoid direct sunlight and high humidity locations. Do not use or store the machine near a space heater, iron, halogen lamp, or other hot objects. 2. Use only neutral soaps or detergents to clean the case. Benzene, thinner, and scouring powders can damage the case and machine, and should never be used. 3. Do not drop or hit the machine. 4. Always consult the operation manual when replacing or installing any assemblies, the presser feet, needle, or other parts to assure correct installation.
For repair or adjustment In the event a malfunction occurs or adjustment is required, first follow the troubleshooting table in the back of the operation manual to inspect and adjust the machine yourself. If the problem persists, please consult your local authorized Brother dealer.
For additional product information and updates, visit our web site at www.brother.com
The contents of this manual and specifications of this product are subject to change without notice.
3 LS2125TOC.fm Page 4 Thursday, February 28, 2008 11:07 AM
———————————————————————————————————————————————————————————————
CONTENTS
1. KNOWING YOUR SEWING MACHINE ...... 6 NAMES OF MACHINE PARTS AND THEIR FUNCTIONS ...... 6 The main parts ...... 6 Needle and presser foot section ...... 8 Flat bed attachment ...... 8 ACCESSORIES ...... 9 USING YOUR SEWING MACHINE ...... 10 Power supply precautions ...... 10 Power supply ...... 10 Foot controller ...... 11 Steadying the machine ...... 11 THREADING THE MACHINE ...... 12 Winding the bobbin ...... 12 Lower threading ...... 14 Upper threading ...... 16 Drawing up the lower thread ...... 18 REPLACING THE NEEDLE ...... 19 Needle precautions ...... 19 Selecting the needle depending on the thread and fabric types ...... 19 Checking the needle ...... 20 Replacing the needle ...... 20 Sewing with a twin needle (Option) ...... 22 REPLACING THE PRESSER FOOT ...... 23 Replacing the presser foot ...... 23 Removing the presser foot holder ...... 24 2. SEWING BASICS ...... 25 SEWING ...... 25 General sewing procedure ...... 25 Selecting stitching ...... 26 Starting to sew ...... 27 Sewing in reverse ...... 28 Thread tension ...... 28 USEFUL SEWING TIPS ...... 30 Trial sewing ...... 30 Changing the sewing direction ...... 30 Sewing curves ...... 30 Sewing thick fabrics ...... 30 Sewing thin fabrics ...... 31 Sewing stretch fabrics ...... 31 Using a free-arm style ...... 31 3. UTILITY STITCHES ...... 32 USEFUL STITCHES ...... 32 Zigzag stitches ...... 32 Basic stitching ...... 33 Blind hem stitching ...... 33 Darning ...... 35 BUTTONHOLE SEWING ...... 36 Making the buttonhole ...... 36 Adjusting buitching stitching ...... 38 Button sewing ...... 38
4 LS2125.book Page 5 Tuesday, February 26, 2008 1:43 PM
ZIPPER INSERTION ...... 40 APPLIQUÉ, MONOGRAMMING AND EMBROIDERING ...... 41 Appliqués ...... 41 Monogramming and embroidering ...... 41 DECORATIVE STITCHING ...... 43 Gathering ...... 43 Shell tuck stitching ...... 43 Elastic stitching ...... 44 4. APPENDIX ...... 45 MAINTENANCE ...... 45 Oiling ...... 45 Changing the bulb ...... 45 Cleaning the machine surface ...... 46 Cleaning the shuttle race ...... 46 Cleaning the feed dogs ...... 47 Repacking the machine ...... 48 Bobbin case tension adjustment ...... 48 TROUBLESHOOTING ...... 50 INDEX ...... 53
5 LS2125.book Page 6 Tuesday, February 26, 2008 1:43 PM
KNOWING YOUR SEWING MACHINE ——————————————————————————————————————————————
1 KNOWING YOUR SEWING MACHINE
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS
The main parts
a Buttonhole fine-adjusting screw (page 38) d Upper tension control dial (page 28) Turn the buttonhole fine-adjusting screw to adjust This controls the tension of the upper thread. buttonhole stitching when it is not uniform. e Flat bed attachment with accessory storage (page 8 and b Pattern selection dial (page 26) 31) Turn the pattern selection dial to select the number of f Reverse sewing lever (page 28) the stitch that you want to use. Press and hold down the reverse sewing lever to sew in c Thread take-up lever (page 16) the opposite direction.
6 LS2125.book Page 7 Tuesday, February 26, 2008 1:43 PM
1
g Built-in handle n Presser foot lever (page 16) h Spool pin (page 12 and 16) Use the presser foot lever to raise and lower the presser The spool pin holds the spool of thread. foot. i Bobbin winder (page 12) o Bobbin winding pre-tension disc/thread guide (page 12 The bobbin winder winds thread onto the bobbin for and 16) use as the lower thread. The thread guide/bobbin winding pre-tension disc is j Handwheel used when winding the thread onto the bobbin and Use the handwheel to manually raise and lower the threading the machine. needle. p Foot controller (page 11) Use the foot controller to control the sewing speed and k Main power/sewing light switch (page 10) Use this switch to turn on and off the main power and to start and stop sewing. sewing light. Part code; XC7359-021 (110/120V Area), l Foot controller jack/jack XC7438-321 (220/240V Area), Insert the foot controller plug into the foot controller XC7456-321 (U.K.), jack, which also supplies power to this machine. XE0629-001 (Australia, New Zealand), m Thread cutter (page 28) XD0852-021 (Korea), Pass the threads through the thread cutter to cut them. XC7438-321 (Russia)
7 LS2125.book Page 8 Tuesday, February 26, 2008 1:43 PM
KNOWING YOUR SEWING MACHINE ——————————————————————————————————————————————
Needle and presser foot Flat bed attachment section The accessories are stored in a compartment inside the flat bed attachment.
Lift the bottom of the flat bed attachment a toward you, and then pull the flat bed attachment out to remove it.
a Flat bed attachment b Storage compartment
a Presser foot holder assembly The presser foot is installed onto the presser foot holder Note assembly. ● Put the accessories in the bag, and then b Presser foot screw store the bag inside the compartment. If the Use the presser foot screw to hold the presser foot holder assembly in place. accessories are not in a bag, they may fall out, and be lost or damaged. c Presser foot (Zigzag) The presser foot applies pressure consistently on the fabric as the sewing takes place. Attach the appropriate presser foot for the selected stitching. d Feed dogs The feed dogs feed the fabric in the sewing direction. e Needle plate The needle plate is marked with guides for sewing straight seams. f Shuttle hook g Shuttle cover Open the shuttle cover to set the bobbin. h Bobbin case i Needle j Needle bar thread guide k Needle clamp screw Use the needle clamp screw to hold the needle in place.
8 LS2125.book Page 9 Tuesday, February 26, 2008 1:43 PM
ACCESSORIES
The following accessories are stored in the flat bed attachment. We have designed these accessories to help you be able to carry out most sewing tasks. 1 Note (For U.S.A. only) ● Foot controller: Model KD-1902, N This foot controller can be used on the following machine models: LS-2220/2720/1520/2125/2125i. ● The screw of the presser foot holder is available through your authorized dealer. (Part code: 132730-122) ● A replacement for the factory-installed presser foot is available through your authorized dealer. (Part number: 138135-122)
1. 2. 3. 4.
5. 6. 7. 8. 75/11 1 needle 90/14 1 needle 100/16 1 needle
Part Code Part Code No. Part Name No. Part Name U.S.A. / Canada Others U.S.A. / Canada Others 1 Buttonhole foot “A” X59369-321 5 Bobbin (3) SA156 XA5539-151 2 Zipper foot “I” X59370-021 6 Needle set 129583-021 3 Button sewing foot “M” XE2137-001 7 Screwdriver X55467-021 4 Darning plate XA3442-121 8 Extra spool pin 130920-021
9 LS2125.book Page 10 Tuesday, February 26, 2008 1:43 PM
KNOWING YOUR SEWING MACHINE ——————————————————————————————————————————————
USING YOUR SEWING MACHINE
Power supply precautions Be sure to observe the following precautions concerning the power supply. WARNING
● Use only regular household electricity for the power source. Using other power sources may result in fire, electric shock, or damage to the machine. ● Turn off the main power and remove the plug in the following circumstances: • When you are away from the machine • After using the machine • When the power fails during use • When the machine does not operate correctly due to a bad connection or a disconnection • During electrical storms
CAUTION
● Do not use extension cords or multi-plug adapters with many other appliances plugged in to them. Fire or electric shock may result. ● Do not touch the plug with wet hands. Electric shock may result. ● When unplugging the machine, always turn off the main power first. Always grasp the plug to remove it from the outlet. Pulling on the cord may damage the cord, or lead to fire or electric shock. ● Do not allow the power cord to be cut, damaged, modified, forcefully bent, pulled, twisted, or bundled. Do not place heavy objects on the cord. Do not subject the cord to heat. These things may damage the cord and cause fire or electric shock. If the cord or plug is damaged, take the machine to your authorized dealer for repairs before continuing use. ● Unplug the power cord if the machine is not to be used for a long period of time. Otherwise a fire may result.
Set the main power switch to “I”. Power supply b
Insert the foot controller plug, located a between the foot controller and the power supply plug on the cord, into the jack on the machine. Then, insert the power supply plug into a wall outlet. X The sewing lamp comes on when the machine is turned on.
a Foot controller plug
10 LS2125.book Page 11 Tuesday, February 26, 2008 1:43 PM
To turn off the machine, set the main power c switch to “{”. Foot controller X The sewing lamp goes off when the machine is turned off. CAUTION ● When connecting the foot controller, be sure 1 Note to turn off the sewing machine in order to ● If a power outage occurs while the sewing prevent the machine from accidentally being machine is being operated, turn off the started. sewing machine and unplug the power When you press the foot controller down lightly, the supply cord. When restarting the sewing machine will run at a low speed. When you press machine, follow the necessary procedure to harder, the machine’s speed will increase. When you correctly operate the machine. take your foot off the foot controller, the machine (For U.S.A. only) will stop. ● This appliance has a polarized plug (one blade wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If Slower the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified Faster electrician to install the proper outlet. Do You should make sure that nothing is placed on the not modify the plug in any way. foot controller when the machine is not in use. CAUTION
● Do not allow pieces of cloth and dust to build up on the foot controller. Doing so could cause a fire or an electric shock. ● A new sewing machine or one that has not been in use for a long period of time should be oiled as described on page 45. After oiling, be sure to wipe off any excess oil.
Steadying the machine If the sewing machine has been placed on an uneven surface, turn the rubber cushion in the right-front corner of the base plate to adjust its height until the sewing machine is stable.
11 LS2125.book Page 12 Tuesday, February 26, 2008 1:43 PM
KNOWING YOUR SEWING MACHINE ——————————————————————————————————————————————
THREADING THE MACHINE
Winding the bobbin
This section describes how to wind the thread onto the bobbin.
1 Pulling it in as far as possible.
a Pre-tension disk b Bobbin winder shaft c Bobbin CAUTION
● Only use bobbins (part code: SA156, SFB: XA5539-151) that have been designed for this sewing machine. Using other bobbins may cause damage to the machine. ● We designed the bobbin that comes with this machine. If you use bobbins from other models, the machine will not work properly. Only use the bobbin that comes with this machine or bobbins of the same type (part code: SA156, SFB: XA5539-151). Actual size
11.5 mm (7/16 inches) This model Other models
Pull up the spool pin as far as possible, and Put the bobbin onto the bobbin winder shaft a then put a spool of thread on this pin. d and slide the bobbin winder shaft to the right. Turn the bobbin clockwise, by hand, until the Pass the thread around the pre-tension disk. spring on the shaft slides into the groove of b the bobbin. CAUTION
● If the spool of thread is not in the right place, the thread may tangle on the spool pin.
Pass the end of the thread through the hole on c the bobbin from the inside of the bobbin. a Spring on the shaft b Groove of the bobbin
Turn on the sewing machine. e
12 LS2125.book Page 13 Tuesday, February 26, 2008 1:43 PM
While holding the end of the thread, gently Cut the thread, slide the bobbin winder shaft f press the foot controller to wind the thread j to the left and remove the bobbin. around the bobbin a few times. Then stop the machine. Memo ● When the sewing machine is started or the 1 handwheel is turned after winding the thread around the bobbin, the machine will make a clicking sound; this is not a malfunction. ● The needle bar does not move when you slide the bobbin winding shaft to the right.
CAUTION
Trim the excess thread above the bobbin. ● Winding the bobbin improperly may cause g the thread tension to loosen, breaking the needle and resulting in injury.
CAUTION
● Make sure you follow the instructions 1 2 carefully. If you do not cut the thread a Wound evenly completely, and the bobbin is wound, when b Wound poorly the thread runs low it may tangle around the bobbin and cause the needle to break.
Press the foot controller to start. h
When the bobbin seems full and begins i spinning slowly, take your foot off the foot controller.
13 LS2125.book Page 14 Tuesday, February 26, 2008 1:43 PM
KNOWING YOUR SEWING MACHINE ——————————————————————————————————————————————
Open the shuttle cover behind the flat bed Lower threading b attachment at the front of the machine. Install the bobbin wound with thread.
CAUTION
● Winding the bobbin improperly may cause the thread tension to loosen, breaking the needle and resulting in injury.
a Flat bed attachment b Shuttle cover
Remove the bobbin case by pulling its latch 1 2 c toward you and pulling it out from the shuttle a Wound evenly race. b Wound poorly ● The bobbin was designed specifically for this sewing machine. If bobbins from other models are used, the machine will not operate correctly. Use only the enclosed bobbin or bobbins of the same type (part code: SA156, SFB: XA5539-151). Actual size
11.5 mm a Bobbin case latch (7/16 inches) Unwind about 10 cm (4 inches) of thread This model Other models d from a full bobbin, and then insert the bobbin into the bobbin case. CAUTION
● Make sure you turn the power off while threading the machine. If you accidentally step on the foot controller and the machine starts to sew, you could be injured.
Raise the needle to its highest position by turning • Only use bobbins that were designed to be a the handwheel toward you (counterclockwise) used with this machine. and raise the presser foot lever. CAUTION
● Make sure you set the bobbin so the thread unrolls in the right direction. If the thread unrolls in the wrong direction, it may cause the thread tension to be incorrect or break the needle.
14 LS2125_01.fm Page 15 Thursday, February 28, 2008 11:08 AM
Pull the trailing thread through the slot, down e and to the left, as shown below, until it enters the delivery eye under the tension spring. 1
a Tension spring
Hold the bobbin case by the latch, fully insert f the bobbin case into the shuttle race, and then release the latch. • Make sure the bobbin case finger fits into the notch at the top of the shuttle race.
a Bobbin case finger b Notch
Close the shuttle cover. g CAUTION
● Make sure that the bobbin case is properly placed back into the machine. If it is incorrectly installed, it will fall out from the shuttle when the machine starts to sew.
15 LS2125.book Page 16 Tuesday, February 26, 2008 1:43 PM
KNOWING YOUR SEWING MACHINE ——————————————————————————————————————————————
Upper threading Set the upper thread and thread the needle.
a Spool pin b Thread guide (rear) c Thread guide (front) d Thread take-up lever
CAUTION
● Make sure you thread the machine properly. Otherwise, the thread could tangle and break the needle.
Raise the presser foot using the presser foot Pull up the spool pin as far as possible, and a lever. c then put a spool of thread on this pin. CAUTION
● If the spool of thread is in the wrong place, or is set incorrectly, the thread may tangle on the spool pin and cause the needle to break.
Feed the upper thread through both thread d guides: the rear one first, then the front one. a Presser foot lever Pull the thread down and around the upper Raise the needle by turning the handwheel e tension control dial from the right to the left b toward you (counterclockwise) to raise the so the thread picks up the thread check thread take-up lever to its highest position. spring.
• If the needle is not correctly raised, the sewing machine can not be threaded. Be sure to turn the handwheel before threading a Upper tension control dial the sewing machine. b Thread check spring
16 LS2125_01.fm Page 17 Tuesday, February 26, 2008 2:58 PM
While holding the thread as shown below, Put the thread behind the needle bar thread f pull it between the tension discs. h guide above the needle. The thread can easily be passed behind the needle bar thread guide by holding the thread in your left hand, then feeding the thread with your right hand. 1
Guide the thread through the thread take-up g lever from right to left. a Needle bar thread guide
Thread the needle from front to back and pull i out about 5 cm (2 inches) of thread.
a Thread take-up lever
a 5 cm (2 inches)
Note ● If the thread take-up lever is lowered, the upper thread cannot be wrapped around the thread take-up lever. Make sure you raise the presser foot lever and the thread take-up lever before you feed the upper thread. ● If you incorrectly feed the thread you may cause sewing problems.
17 LS2125.book Page 18 Tuesday, February 26, 2008 1:43 PM
KNOWING YOUR SEWING MACHINE ——————————————————————————————————————————————
Drawing up the lower thread
Lightly hold the end of the upper thread. Pull out about 15 cm (6 inches) of both a d threads and pull them toward the back of the machine under the presser foot.
a Upper thread While holding the end of the upper thread, a Upper thread b raise the needle to its highest position by b Lower thread turning the handwheel toward you (counterclockwise).
Pull on the upper thread to draw up the lower c thread.
a Upper thread b Lower thread
18 LS2125.book Page 19 Tuesday, February 26, 2008 1:43 PM
REPLACING THE NEEDLE
This section provides information on sewing machine needles. 1 Needle precautions Be sure to observe the following precautions concerning the handling of the needle. Failure to observe these precautions is extremely dangerous. Be sure to read and carefully follow the instructions below. CAUTION
● Only use home sewing machine needles. Use of any other needle may bend the needle or damage the machine. ● Never use bent needles. Bent needles can easily break, possibly resulting in injury.
Selecting the needle depending on the thread and fabric types The sewing machine needle that should be used depends on the fabric and thread thickness. Refer to the following table when choosing the thread and needle appropriate for the fabric that you wish to sew. Use the same size thread for the upper (spool) and lower (bobbin) threads.
Sewing fabrics Needle sizes Thread sizes
Fine tricot, Fine lace, Cotton: 80 Very thin Thin linen, Silk, 65/9 Synthetic/ Polyester Long Organza, Chiffon Fiber Fine Mercerized Cotton Cotton: 60-80 Silk: “A” Lightweight Voile, Taffeta, 75/11 Synthetic/ Polyester Long Synthetics, Silk, Batiste Fiber Mercerized 50
Cotton, Gingham, Cotton: 50-60 Poplin, Percale, Pique, Silk: “A” Medium weight Satin, Velvet, 90/14 (Supplied with Synthetic/ Polyester Long Lightweight wool, your machine.) Fiber Fine corduroy, Suitings, Mercerized 50-60 Linen, Muslin Denim, Gabardine, Cotton: 40-50 Heavyweight Tweed, Corduroy, 100/16 Mercerized Heavy Duty Canvas, Duck Polyester Long Fiber Cotton Wrapped Knits Single knit, Double knit, 90/14 (Ball point) Polyester Jersey, Tricot Polyester Long Fiber
Memo ● The smaller the thread number, the thicker the thread; and the larger the needle number, the thicker the needle. ● Use the ball point needle when sewing on stretch fabrics or fabrics where skipped stitches easily occur. ● Use a 90/14 to 100/16 needle with transparent nylon threads, regardless of the fabric being sewn. ● A 75/11 needle is already installed when the sewing machine is purchased.
19 LS2125.book Page 20 Tuesday, February 26, 2008 1:43 PM
KNOWING YOUR SEWING MACHINE ——————————————————————————————————————————————
CAUTION Replacing the needle ● The appropriate fabric, thread and needle Replace the needle as described below. Use the combinations are shown in the table on the screwdriver and a needle that has been determined previous page. If the combination of the to be straight according to the instructions in fabric, thread and needle is not correct, “Checking the needle” . particularly when sewing thick fabrics (such as denim) with thin needles (such as 65/9 to Turn off the sewing machine. 75/11), the needle may bend or break. In a addition, the stitching may be uneven or puckered or there may be skipped stitches.
Checking the needle Sewing with a bent needle is extremely dangerous since the needle may break while the machine is being operated. CAUTION Before using the needle, place the flat side of the ● Before replacing the needle, be sure to turn needle on a flat surface and check that the distance off the sewing machine, otherwise injuries between the needle and the flat surface is even. may occur if the foot controller is accidentally pressed and the machine starts sewing.
1 Raise the needle to its highest position by b 2 turning the handwheel toward you (counterclockwise).
a Flat side b Needle type marking ■ Correct needle
Lower the presser foot lever. c
1
a Flat surface ■ Incorrect needle If the distance between the needle and the flat surface is not even, the needle is bent. Do not use a bent needle. a Presser foot lever
1
a Flat surface
20 LS2125.book Page 21 Tuesday, February 26, 2008 1:43 PM
Hold the needle with your left hand, and then While holding the needle with your left hand, d use a screwdriver to turn the needle clamp f use the screwdriver to tighten the needle screw counterclockwise to remove the clamp screw by turning it clockwise. needle.
Note 1 ● The needle can be removed by simply loosening the needle clamp screw about one turn. (If the needle clamp screw is loosened too much, the needle clamp Install the twin needle in the same way. (which holds the needle) may fall off. Therefore, do not loosen the needle clamp screw too much.)
CAUTION
● Be sure to insert the needle until it touches the needle stopper and securely tighten the needle clamp screw with the screwdriver, a Screwdriver b Needle clamp screw otherwise the needle may break or damage • Do not apply strong force when loosening or may result. tightening the needle clamp screw, ■ otherwise certain parts of the sewing Installing the needle clamp machine may be damaged. If the needle clamp is removed, follow the procedure below to attach it to the needle bar. As seen from the front of the machine, slide a the needle clamp onto the needle bar so that the needle clamp screw is on the right side and the needle bar thread guide is at the bottom.
With the flat side of the needle toward the e rear of the machine, insert the needle until it touches the needle stopper.
a Needle clamp screw b Needle bar thread guide c Needle bar Align the bottom edge of the needle holder b with the end of the needle bar, and then tighten the needle clamp screw.
a Needle stopper
a Needle bar b Needle holder c Needle clamp screw d Align
21 LS2125.book Page 22 Tuesday, February 26, 2008 1:43 PM
KNOWING YOUR SEWING MACHINE ——————————————————————————————————————————————
Sewing with a twin needle (Option) We have designed your machine so you can sew with the optional twin needle and two top threads. You can use the same color or two different colors of thread for making decorative stitches. The stitches available for twin-needle sewing are straight stitches 6 through 10 and zigzag stitch 2. CAUTION
● Use only twin needles that have been made for this machine (part code: X57521-021). Other needles could break, and damage the machine. ● Do not sew with bent needles. The needle could break and injure you. ● When using the twin needle, be sure to select an appropriate stitch (straight stitches 6 through 10 and zigzag stitch 2), otherwise the needle may break or the machine may be damaged. ● Slowly turn the handwheel toward you (counterclockwise) and check that the needle does not touch the presser foot. If the needle hits the presser foot, the needle may bend or break. ● When changing the sewing direction, be sure to raise the needle before turning the fabric. If the fabric is turned while the needle is lowered, the needle may bend or break.
■ Twin needle threading Thread the right needle from front to back. f Do not pass the thread behind the needle bar Attach the twin needle. thread guide. a Attach the twin needle in the same way as a single needle (page 20). Attach the extra spool pin. b Put the extra spool pin in the hole on the top of the machine. Put the second spool of thread onto the extra spool pin.
a Left needle thread passes through the needle bar thread guide. b Right needle thread passes in front of the needle bar thread guide. c Needle bar thread guide
a First spool b Second spool
Use the thread from the first spool to thread c the machine to the needle bar thread guide. The path for threading the machine to the needle bar thread guide is the same as for normally threading the machine (for a single needle). See page 16 for more details. Thread the left needle from front to back. d
Use the thread from the second spool to thread e the machine to the thread take-up lever. The path for threading the machine to the thread take-up lever is the same as for normally threading the machine (for a single needle). See page 16 for more details.
22 LS2125.book Page 23 Tuesday, February 26, 2008 1:43 PM
REPLACING THE PRESSER FOOT
CAUTION 1 ● Always turn off the power before you change the presser foot. If you leave the power on and step on the controller, the machine will start and you may be injured. ● Always use the correct presser foot for the stitch pattern you have chosen. If you use the wrong presser foot, the needle may strike the presser foot and bend or break, and may cause injury. ● Only use presser feet that have been designed to be used with this machine. Using other any presser feet may cause an accident or injury.
Press the black button at the back of the Replacing the presser foot d presser foot holder to release the presser foot. Replace the presser foot as described below.
If the sewing machine has been turned on, a turn it off.
a Black button b Presser foot holder CAUTION Place a different presser foot below the holder ● Before replacing the presser foot, be sure to e so that the presser foot pin is aligned with the turn off the sewing machine, otherwise shank in the holder. injuries may occur if the foot controller is Position the presser foot so the letter indicating accidentally pressed and the machine starts the presser foot type (A, I, etc.) is positioned to sewing. be read. Raise the needle to its highest position by b turning the handwheel toward you (counterclockwise).
a Presser foot holder b Shank c Pin
Slowly lower the presser foot lever so that the f presser foot pin snaps into the shank in the Raise the presser foot lever. presser foot holder. c
a Presser foot lever a Presser foot lever X The presser foot is attached.
23 LS2125.book Page 24 Tuesday, February 26, 2008 1:43 PM
KNOWING YOUR SEWING MACHINE ——————————————————————————————————————————————
Raise the presser foot lever to check that the ■ Attaching the presser foot holder g presser foot is securely attached. Align the presser foot holder with the lower- a left side of the presser bar.
Removing the presser foot a Presser foot holder holder b Presser bar
Remove the presser foot holder when cleaning the Hold the presser foot holder in place with sewing machine or when installing a presser foot that b your right hand, and then tighten the screw does not use the presser foot holder, such as the using the screwdriver in your left hand. quilting foot. Use the screwdriver to remove the presser foot holder. ■ Removing the presser foot holder
Remove the presser foot. a • For details, refer to “Replacing the presser foot” (page 23).
Use the screwdriver to loosen the presser foot a Screwdriver b holder screw. b Presser foot holder c Presser foot holder screw
Note ● If the presser foot holder is not correctly installed, the thread tension will be incorrect.
a Screwdriver b Presser foot holder c Presser foot holder screw
24 LS2125.book Page 25 Tuesday, February 26, 2008 1:43 PM
2 SEWING BASICS
SEWING
Basic sewing operations are described below. Before operating the sewing machine, read the following precautions. 2 CAUTION
● While the machine is in operation, pay special attention to the needle location. In addition, keep your hands away from all moving parts such as the needle and handwheel, otherwise injuries may occur. ● Do not pull or push the fabric too hard while sewing, otherwise injuries may occur or the needle may break. ● Never use bent needles. Bent needles can easily break, possibly resulting in injuries. ● Make sure that the needle does not strike basting pins, otherwise the needle may break or bend.
General sewing procedure Follow the basic procedures below to sew.
Turn on the Turn on the sewing machine. 1 machine. For details on turning on the machine, refer to “Power supply” (page 10).
p
Select the stitch appropriate for the area to be sewn. 2 Select the stitch. For details on selecting a stitch, refer to “Selecting stitching” (page 26).
p
Attach the presser Attach the presser foot appropriate for the stitch. 3 foot. For details on replacing the presser foot, refer to “Replacing the presser foot” (page 23).
p
Position the fabric, and then start sewing. When sewing is finished, cut the 4 Start sewing. threads. For details on starting to sew, refer to “Starting to sew” (page 27).
25 LS2125_02.fm Page 26 Tuesday, February 26, 2008 2:58 PM
SEWING BASICS ————————————————————————————————————————————————————————
Selecting stitching Turning the stitch selection dial in either direction, select the desired stitch.
aPattern selection dial
Number on dial Stitch name Pattern Page
bacd 1 4-step automatic 36 buttonhole
2 Zigzag stitch
3 Zigzag stitch
32, 41 4 Zigzag stitch
5 Zigzag (satin) stitch
6 Straight stitch 33, 35, (Center needle position) 40, 43 Select the desired length.
7 Straight stitch 33 (Left needle position)
Stretch blind 8 Stitch 33
9 Shell tuck stitch 43
10 Elastic stitch 44
26 LS2125.book Page 27 Tuesday, February 26, 2008 1:43 PM
While holding the end of the thread and the Starting to sew e fabric with your left hand, turn the handwheel toward you (counterclockwise) with your Turn on the sewing machine. right hand to lower the needle to the starting a point of the stitching.
2 Raise the needle to its highest position by b turning the handwheel toward you (counterclockwise).
Lower the presser foot lever. f
Raise the presser foot lever. c
a Presser foot lever
Slowly press down on the foot controller. g
a Presser foot lever
Place the fabric under the presser foot, pass d the thread under the presser foot, and then pull out about 5 cm (2 inches) of thread toward the rear of the machine.
X The machine starts sewing.
Take your foot off the foot controller. h X The machine stops sewing.
Raise the needle to its highest position by i turning the handwheel toward you a 5 cm (2 inches) (counterclockwise).
Raise the presser foot lever. j
27 LS2125.book Page 28 Tuesday, February 26, 2008 1:43 PM
SEWING BASICS ————————————————————————————————————————————————————————
Pull the fabric to the left side of the machine, k and then pass the threads through the thread Thread tension cutter on the back of the presser foot bar to cut them. The thread tension will affect the quality of your stitches. You may need to adjust it when you change fabric or thread.
Memo ● Before beginning to change tension adjustments make sure the upper thread and bobbin are inserted correctly. ● We recommend you do a test sample on a scrap of fabric before you start to sew.
■ Correct tension a Thread cutter Correct tension is important as too much or too little tension will weaken your seams or cause puckers on your fabric. Sewing in reverse 1 Reverse sewing is used to lock the threads at the end of the seam or wherever reinforcement is needed. a Wrong side 2 b Surface Press and hold down the reverse sewing lever c Upper thread a while sewing. d Lower thread 3 4 ■ Upper tension is too tight Loops appear on the surface of the fabric.
Note ● If the bobbin thread was incorrectly inserted, the upper thread may be too tight. In this case, refer to “Lower threading” To sew forward, release the reverse sewing (page 14) and reinsert the bobbin. b lever.
1
a Wrong side b Surface 2 c Upper thread d Lower thread e Loops appear on 3 5 surface of fabric 4 Solution Reduce the tension by turning the upper tension- control dial to a lower number.
28 LS2125.book Page 29 Tuesday, February 26, 2008 1:43 PM
■ Upper tension is too loose ■ Bobbin tension is too loose Loops appear on the wrong side of the fabric. Loops may appear on the surface of the fabric when sewing thin fabric with thin thread. 1
Note a Wrong side ● If the upper thread was incorrectly b Surface threaded, the upper thread may be too 2 c Upper thread loose. In this case, refer to “Upper d Lower thread e Loops appear on threading” (page 16) and rethread. 3 5 surface of fabric 4 5 1 2 Solution a Wrong side Reduce the tension by b Surface turning the upper tension- 2 c Upper thread control dial to a lower d Lower thread e Loops appear on number. 3 wrong side of fabric If the problem persists, increase the tension in 4 the bobbin by turning the screw clockwise Solution with a small screwdriver. Increase the tension by Be sure not to turn the screw more than one turning the upper tension- full turn. In addition, be sure to return the control dial to a higher screw to its original position before the next number. time that the machine is used.
Note ● The bobbin thread tension has been adjusted at the factory for general use. For most sewing applications, no adjustment is needed.
29 LS2125.book Page 30 Tuesday, February 26, 2008 1:43 PM
SEWING BASICS ————————————————————————————————————————————————————————
USEFUL SEWING TIPS
Various ways to achieve better results for your sewing projects are described below. Refer to these tips when sewing your project.
Trial sewing Sewing curves A trial piece of fabric should be sewn since, depending Stop sewing, and then slightly change the sewing on the type of fabric and stitching being sewn, the direction to sew around the curve. desired results may not be achieved. For the trial sewing, use a piece of fabric and thread that are the same as those used for your project, and check the thread tension and stitch length and width. Since the results differ depending on the type of stitching and the number of layers of fabric sewn, perform the trial sewing under the same conditions that will be used with your project.
Changing the sewing When sewing along a curve while using a zigzag direction stitch, select a shorter stitch length in order to obtain a finer stitch. When the stitching reaches a corner, stop the a sewing machine. Leave the needle lowered (in the fabric). If the needle was raised, lower the needle by turning the handwheel toward you (counterclockwise). CAUTION
● When using the twin needle, be sure to raise the needle before changing the sewing direction. If the fabric is turned while the needle is lowered, the needle may bend or Sewing thick fabrics break. ■ If the fabric does not fit under the presser foot Raise the presser foot lever, and then turn the If the fabric does not fit easily under the presser b fabric. foot, raise the presser foot lever even higher to Turn the fabric using the needle as a pivot. bring the presser foot to its highest position.
Lower the presser foot lever and continue c sewing. CAUTION
● If fabric more than 6 mm (15/64 inches) thick is sewn or if the fabric is pushed with too much force, the needle may bend or break.
30 LS2125.book Page 31 Tuesday, February 26, 2008 1:43 PM
Sewing thin fabrics When sewing thin fabrics, the stitching may become misaligned or the fabric may not feed correctly. If this occurs, place thin paper or stabilizer material under the fabric and sew it together with the fabric. When you have finished sewing, tear off any excess paper. 2
a Stabilizer material or paper
Sewing stretch fabrics First, baste the pieces of fabric together, and then sew without stretching the fabric.
a Basting
Using a free-arm style Free-arm sewing is convenient for sewing tubular and hard-to-reach areas. To change your machine to the free-arm style, lift the bottom of the flat bed attachment toward you, and then pull the flat bed attachment out to remove it.
a Flat bed attachment
31 LS2125.book Page 32 Tuesday, February 26, 2008 1:43 PM
UTILITY STITCHES ———————————————————————————————————————————————————————
3 UTILITY STITCHES
USEFUL STITCHES
Start sawing. Zigzag stitches c You can use the zigzag stitches to join together seams and finish them in one operation. They are also useful for sewing stretch materials.
Number Stitch name Application on dial 2 Zigzag stitch
Overcasting and 3 • For details, refer to “Starting to sew” Zigzag stitch attaching appliqués. Select the desired (page 27). width. 4 Zigzag stitch Memo ● When sewing with a zigzag stitch, use straight stitches at the beginning and end of 5 Overcasting and Zigzag (satin) attaching appliqués the zigzag stitch for reinforcement. stitch with the decorative satin stitches. When sewing is finished, cut the thread. Select a stitch. d a • For details, refer to “Starting to sew” • For details, refer to “Selecting stitching” (page 27). (page 26). CAUTION Lower the needle into the fabric at the ● b beginning of the stitching. Slowly turn the handwheel toward you (counterclockwise) and check that the needle does not touch the presser foot. If the needle hits the presser foot, the needle may bend or break.
32 LS2125.book Page 33 Tuesday, February 26, 2008 1:43 PM
Basic stitching Blind hem stitching Straight stitches are used for sewing plain seams. You can use the Blind Hem Stitch to finish the edge Two stitches are available for basic stitching. of a project, like the hem of a pair of trousers, without the stitch showing. Number on dial Stitch name Application Number 6 Attaching Stitch name Application Straight stitch zippers, basic on dial (Center needle stitching, and 8 position) sewing gathers Stretch blind Blind hem stitching on or darning, etc. Stitch stretch fabrics. 7 Straight stitch Basic stitching, (Left needle sewing gathers position) or pintucks, etc. Reverse the skirt or pants. a
Baste or pin together the fabric pieces. 3 a
Select a stitch. b • For details, refer to “Selecting stitching” (page 26). a Right side of fabric b Bottom side Lower the needle into the fabric at the c beginning of the stitching. Fold the fabric along the desired edge of the b hem, and press. Start sewing. d • For details, refer to “Starting to sew” (page 27).
When sewing is finished, cut the thread. e • For details, refer to “Starting to sew” (page 27).
33 LS2125.book Page 34 Tuesday, February 26, 2008 1:43 PM
UTILITY STITCHES ———————————————————————————————————————————————————————
Use a chalk to mark on the fabric about 5 mm Unfold the edge of fabric, and position the c (3/16 inches) from the edge of the fabric, and e fabric with the wrong side facing up. then baste it.
Fold back the fabric inside along the basting. Remove the flat bed attachment and make d g free-arm sewing possible. • For details on free-arm sewing, refer to“Using a free-arm style” (page 31).
Slide the part that you wish to sew onto the h arm, make sure that the fabric feeds correctly, and then start sewing.
34 LS2125.book Page 35 Tuesday, February 26, 2008 1:43 PM
Position the fabric so that the needle slightly i catches the fold of the hem, and then lower Darning the presser foot lever. For invisible stitching, make sure that both Reinforce points that will be subject to strain. threads are the same color as the fabric. Number on dial Stitch name Application Attaching 6 Straight stitch zippers, basic (Center needle stitching, and position) sewing gathers or darning, etc.
Place the darning plate on the needle plate as a shown below, and then remove both the aNeedle presser foot and presser foot holder assembly. bNeedle drop point cFold of hem dWrong side of fabric 3 Sew along the fold of the hem. j
Remove the basting stitching and turn the k fabric right side up.
Select the desired length for straight stitch (6). b Place the fabric to be darned under the c presser foot together with a fabric underlay for reinforcement.
Start sewing while gently moving the fabric a Wrong side of fabric b Right side of fabric d with your hands, alternately drawing the fabric away and pulling it toward you.
Stop sewing when the portion to be darned is e filled with parallel stitching.
35 LS2125.book Page 36 Tuesday, February 26, 2008 1:43 PM
UTILITY STITCHES ———————————————————————————————————————————————————————
BUTTONHOLE SEWING
Buttonholes can be sewn and buttons can be sewn on.
Number on dial Stitch name Application Memo 1 ● Before sewing buttonholes, check the stitch 4-step Buttonholes on length and width by sewing a trial automatic medium weight buttonhole fabrics. buttonhole on a scrap piece of fabric. ● When sewing buttonholes on stretch fabrics, place stabilizer material under the Buttonholes are sewn from the front of the presser fablic. foot to the back, as shown below.
Step Sewn portion Use chalk to mark the position and length of a the buttonhole on the fabric. Step a (Front end of button hole)
1 Step b (Left side)
Step c (Back end of button hole)
a Marks on fabric
Attach buttonhole foot “A” and push the Step d b outside frame back until the sliding insert (Right side) reaches the front of the outside frame.
Select stitch “a” of the 4-step automatic a Reinforcement stitching c buttonhole (1).
Making the buttonhole Position the fabric under the presser foot so d that the middle of the front chalk line is The names of parts of buttonhole foot “A”, which is directly in the center of the presser foot and used for sewing buttonholes, are indicated below. aligned with the two red lines on the insert. Pass the upper thread down through the hole in the presser foot.
a Presser foot scale b Pin c Marks on buttonhole foot d 5 mm (3/16 inches) a Mark on fabric b Red marks on the sliding insert
Start sewing. Sew 5 to 6 stitches. e
36 LS2125.book Page 37 Tuesday, February 26, 2008 1:43 PM
Stop sewing when the needle is at the left side Insert a pin at the end of the buttonhole f of the stitching, and then raise the needle by p stitching to prevent the stitching from being turning the handwheel toward you. cut, and then use a seam ripper to cut towards the pin and open the buttonhole. Select stitch “b” of the 4-step automatic g buttonhole (1). 2 Start sewing, and then sew the length of the h chalk line.
Stop sewing when the needle is at the right i side of the stitching, and then raise the needle 1 by turning the handwheel toward you. a Seam ripper Select stitch “c” (same as “a”) of the 4-step b Pin j automatic buttonhole (1). CAUTION 3 Start sewing. Sew 5 to 6 stitches. k ● When opening the buttonhole with the seam ripper, do not place your hands in the cutting Stop sewing when the needle is at the right path, otherwise injuries may result if the seam l side of the stitching, and then raise the needle ripper slips. Do not use the seam ripper in any by turning the handwheel toward you. other way than how it is intended.
Select stitch “d” of the 4-step automatic m buttonhole (1).
Start sewing. Sew the right side of the n buttonhole until the needle reaches the
stitching sewn in step e. For reinforcement, turn the fabric 90 degrees counterclockwise, select the straight stitch (6 through 10) with the desired length, and then sew to the edge of the front bar tack.
Raise the presser foot lever, remove the o fabric, and cut the thread.
37 LS2125.book Page 38 Tuesday, February 26, 2008 1:43 PM
UTILITY STITCHES ———————————————————————————————————————————————————————
Adjusting buitching Button sewing stitching Buttons can be sewn on with the sewing machine. If the stitching on the two sides of the buttonhole is Buttons with 2 or with 4 holes can be attached. not uniform, the stitching can adjusted with the buttonhole fine-adjusting screw. Measure the distance between the holes in the a button to be attached, and then select the appropriate zigzag stitch (2, 3 or 4) according to the following table.
Number a Buttonhole fine-adjusting screw Distance between holes of dial ■ If the right side is too loose compared to the left side 1.6 mm (1/16 inches) 2 Use the enclosed large screwdriver to turn 3.2 mm (1/8 inches) 3 the buttonhole fine-adjusting screw in the - 4.8 mm (3/16 inches) 4 direction. Attach the button sewing foot “M”. b
Place the darning plate on the needle plate as c shown below.
■ If the right side is too tight compared to the left side Use the enclosed large screwdriver to turn the buttonhole fine-adjusting screw in the + direction.
Place a button between the presser foot and d the fabric.
• When attaching four-hole buttons, first sew the two holes closest to you. Then, slide the button so that the needle goes into the two holes toward the rear of the sewing machine, and then sew them in the same way.
38 LS2125.book Page 39 Tuesday, February 26, 2008 1:43 PM
Turn the handwheel toward you e (counterclockwise) to check that the needle correctly goes into the two holes of the button.
If the needle hits the button, return to step a.
CAUTION ● When sewing, be sure that the needle does 3 not touch the button, otherwise the needle may bend or break.
Start sewing. f • After sewing for about 10 seconds at a low speed, press and hold down the reverse sewing lever to sew a few reinforcement stitches.
Pull the fabric to the left side of the machine, g and then cut the upper and lower threads, leaving a length of 15 cm (6 inches).
Pull the upper thread at the end of the h stitching to the wrong side of the fabric, and then tie it with the bobbin thread. Use scissors to cut the upper thread and the bobbin thread at the beginning of the stitching.
39 LS2125.book Page 40 Tuesday, February 26, 2008 1:43 PM
UTILITY STITCHES ———————————————————————————————————————————————————————
ZIPPER INSERTION
You can use the zipper foot “I” to sew different types of zippers, and can easily position it to the right or left side of the needle. When sewing the right side of the zipper, attach the shank to the left pin of the zipper foot. When sewing the left side of the zipper, attach the shank to the right pin of the zipper foot.
Number on dial Stitch name Application Sew from the bottom of the zipper toward the d top on both sides. The needle should be 6 Attaching positioned on the zipper side of the foot for Straight stitch zippers, basic (Center needle stitching, and best results. position) sewing gathers or darning, etc.
a Zipper foot “I” b Right pin for sewing the left side of the zipper c Left pin for sewing the right side of the zipper To sew the opposite side of the zipper, release e the foot by pressing the button located at the Select the desired length for straight stitch (6). back of the presser foot, fit the zipper foot on a the other side of the zipper and continue sewing using the other side notch. Lower the presser foot lever and fix either the b left or right pin of the zipper foot onto the CAUTION shank. ● Make sure the needle does not hit the zipper Fold the edge of the fabric 2 cm (3/4 inches) during sewing. If the needle hits the zipper, c and place the zipper under the folded section. the needle may break and you may be injured. Lower the needle into the notch located either on the left or right side of the zipper foot. CAUTION
● Turn the handwheel by hand to make sure the needle does not hit the presser foot before you start sewing. If you choose a different stitch, the needle will hit the presser foot and break the needle. You may also be injured.
40 LS2125.book Page 41 Tuesday, February 26, 2008 1:43 PM
APPLIQUÉ, MONOGRAMMING AND EMBROIDERING
Zigzag stitches can be used for sewing appliqués, monogramming and embroidering.
Number Carefully sew around the edge of the design. Stitch name Application c on dial 2 Zigzag stitch
3 Overcasting and attaching appliqués. Zigzag stitch Select the desired width. 4 Zigzag stitch 3 Memo 5 Overcasting and ● Zigzag (satin) attaching appliqués Make reinforcing straight stitches at the stitch with the decorative beginning and the end of stitching. satin stitches. CAUTION Appliqués ● Be careful that the needle does not hit a pin You can create an appliqué by cutting a different during sewing, as the needle can break. You piece of fabric into a shape and using it as a may also be injured. decoration. Cut away any fabric that is left outside the Baste the cut design to the fabric. d a stitching.
Select a stitch. b
Remove the basting, if necessary. e
Monogramming and embroidering
Place the darning plate on the needle plate as a shown below, and then remove both the presser foot and presser foot holder assembly.
41 LS2125.book Page 42 Tuesday, February 26, 2008 1:43 PM
UTILITY STITCHES ———————————————————————————————————————————————————————
Select a stitch. ■ Monogramming b Sew the lettering at a constant speed by moving the hoop slowly. Draw the lettering (for monogramming) or c design (for embroidering) on the surface of the fabric.
Put the fabric in the embroidery hoop with d the surface of the fabric facing up inside the well.
Place the project under the needle and lower ■ Embroidering e the presser bar. Sew along the outline of the design by moving the hoop slowly. Draw up the lower thread through the project Then, sew to completely fill in the design f at the starting position by turning the with stitches by alternately sewing from the handwheel toward you (counterclockwise), outline of the design to the inside and from and then sew a few stitches to reinforce the the inside to the outline. stitching.
Grip the hoop with the thumbs and Memo g forefingers of both hands while pressing the ● Be sure to keep the stitches close together. fabric with the middle and third fingers, and support the outside of the hoop with your little fingers. Select the desired length for straight stitch (6) i and sew a few stitches for reinforcing.
Memo ● When the hoop is moved quickly, the stitches are longer. When the hoop is moved slowly, the stitches are shorter.
Start sewing. h CAUTION
● Be sure to keep your fingers away from moving parts, especially needles.
42 LS2125.book Page 43 Tuesday, February 26, 2008 1:43 PM
DECORATIVE STITCHING
Various decorative stitches can be sewn with this sewing machine.
Gathering Shell tuck stitching
Number on dial Stitch name Application Number Stitch name Application on dial 6 Attaching zippers, Straight stitch basic stitching, 9 (Center needle and sewing position) gathers or Shell tuck stitch Shell tuck stitching darning, etc.
Select the desired length for straight stitch (6). The gathers that look like shells are called “shell a tucks”. They are used to decorate trims, the front of 3 blouses or cuffs made of thin fabrics. Loosen the tension of the upper thread (to b about 2). Fold the fabric along the bias. • For details, refer to “Thread tension” a (page 28).
Sew a single or multiple parallel rows of c stitches. • Do not sew reverse stitches or cut the thread.
Pull the bobbin threads to create gathers. d Smooth the gathers by ironing them.
Select the shell tuck stitch (9), and increase b the thread tension. • For details, refer to “Selecting stitching” (page 26).
Sew while making sure that the needle drops c slightly off the edge of the fabric.
Unfold the fabric, and then iron the tucks d down to one side.
43 LS2125.book Page 44 Tuesday, February 26, 2008 1:43 PM
UTILITY STITCHES ———————————————————————————————————————————————————————
■ Joining fabric Elastic stitching Put the edges of the two pieces of fabric together, and then place them under the presser foot with the fabric edges under the Number Stitch name Application center of the presser foot. on dial Then, start sewing the edges of the two 10 Mending, sewing fabrics together. Elastic stitching elastic tape or joining fabric.
The elastic stitch can be used in 3 ways: mending, sewing elastic or joining fabric. Each is explained below. Select the elastic stitch (10). ■ Mending Place the reinforcement fabric under the tear to be mended, and then sew over the tear. Memo ● Make reinforcing reverse stitches at the beginning and the end of stitching.
■ Sewing elastic tape Place the elastic tape on the fabric, and then sew over the elastic tape while holding the tape both in front and behind the presser foot.
44 LS2125.book Page 45 Tuesday, February 26, 2008 1:43 PM
4 APPENDIX
MAINTENANCE
Simple sewing machine maintenance operations are described below.
Oiling Changing the bulb
Turn off the machine and unplug it. a CAUTION
Put 2 to 3 drops of oil at each of the points ● Unplug the power supply cord before b indicated below. changing the bulb, otherwise injuries or an Be sure to wipe any excess oil off the electric shock may occur. machine. Turn off the machine and unplug it. a 4
Loosen the face plate screw. b
Remove the face plate from the machine. c
After oiling, run the machine for a short time c at a fast speed without thread.
Memo ● Make sure to oil the machine once a week if Note you use it more than an hour a day. If you ● Hold the face plate securely while removing use it more often, oil every day. or attaching it. ● Sewing machine oil is available at your local sewing machine dealer or service center. ● Do not apply too much oil as it may soil the thread and fabric.
45 LS2125.book Page 46 Tuesday, February 26, 2008 1:43 PM
APPENDIX ——————————————————————————————————————————————————————————
Replace the sewing light bulb. d Cleaning the shuttle race
CAUTION
● Be sure to unplug the machine before cleaning it, otherwise injuries or an electric shock may occur.
Turn off the machine and unplug it. a
Raise the needle and the presser foot, and b a bulb then remove the presser foot and the needle. b Loosen c Tighten Remove the flat bed attachment and open the c shuttle cover at the front of the free arm. Attach the face plate and fasten the screw e again. Remove the bobbin case by pulling its latch d toward you and pulling it out from the shuttle race.
Cleaning the machine surface a Bobbin case latch If the surface of the machine is dirty, lightly soak a cloth in neutral detergent, squeeze it out firmly, and Slide the latch levers out from the retaining e then wipe the surface of the machine. After cleaning ring to remove it. it once with a wet cloth, wipe it again with a dry cloth. CAUTION
● Unplug the power supply cord before cleaning the machine, otherwise injuries or an electric shock may occur. a Retaining ring b Latch lever
46 LS2125.book Page 47 Tuesday, February 26, 2008 1:43 PM
Remove the hook by grasping its center post Attach the bobbin case, the presser foot and f and pulling it out. k the needle before using the machine.
Cleaning the feed dogs
CAUTION
● Make sure you unplug the machine before you clean it. Otherwise, you may get an electric shock or be injured. a Retaining ring b Hook Turn off the machine and unplug it. c Hook center post a
Use a brush to remove any accumulated lint Raise the needle and the presser foot, and g and thread from the retaining ring, hook, b then remove the presser foot and the needle. driver and race body. Remove the flat bed attachment and open the c shuttle cover at the front of the free arm. 4 Remove the needle plate by using a coin or d screwdriver to remove the screws.
a Retaining ring b Driver c Race body
Use a cloth dampened with machine oil to h wipe the shuttle race in order to remove any lint. Use a brush to clean the lint from the upper Clean the lint from the shuttle hook in the e part of the feed dogs and shuttle race body.
i same manner as described in step h.
Reassemble the hook and the retaining ring, j and push the latch levers back into position.
Attach the needle plate by using a coin or f screwdriver.
a Retaining ring b Hook c Latch lever
47 LS2125_Appendix.fm Page 48 Thursday, February 28, 2008 11:09 AM
APPENDIX ——————————————————————————————————————————————————————————
Repacking the machine Note ● Remember to return the screw to its original Keep the carton and packing materials for future use. setting before starting your next project. When packing up the machine again, pack it properly as described below. ■ If it is not packed properly, damage may occur Bobbin tension is too loose during shipping. Loops appear on the surface of the fabric. 1
a Wrong side b Surface 2 c Upper thread d Lower thread e Loops appear on 3 5 surface of fabric 4 Solution Reduce the tension by turning the upper tension- control dial to a lower number.
Note ● If the loops still appear on the surface of the fabric after you adjust the upper tension, the bobbin thread may be too loose. In this case, turn the screw clockwise, being careful not to over-tighten the screw, approximately 30-45 degrees to increase bobbin tension. After you adjust the bobbin thread, adjust the upper thread to match the bobbin thread.
IMPORTANT
● This packing material is designed to prevent damage in transit. ● Save this packing material in case it is needed to transport this sewing machine. a Screw Bobbin case tension adjustment The bobbin thread tension has already been adjusted at the factory for general use. For most sewing applications, no adjustment is needed. When sewing with thin thread on thin fabrics, the thread tension may not be adjusted adequately with the upper tension control dial. Therefore, the thread tension must be adjusted according to the procedure described below.
48 LS2125_Appendix.fm Page 49 Thursday, February 28, 2008 11:09 AM
■ Bobbin tension is too tight Loops appear on the wrong side of the fabric. 5 1
a Wrong side b Surface 2 c Upper thread d Lower thread e Loops appear on 3 wrong side of fabric 4 Solution Increase the tension by turning the upper tension- control dial to a higher number.
Note ● If the loops still appear on the wrong side of the fabric after you adjust the upper tension, 4 the bobbin thread may be too tight. In this case, turn the screw counterclockwise being careful not to over-loosen the screw, approximately 30-45 degrees to decrease bobbin tension. After you adjust the bobbin thread, adjust the upper thread to match the bobbin thread.
a Screw
49 LS2125_Appendix.fm Page 50 Tuesday, February 26, 2008 2:59 PM
APPENDIX ——————————————————————————————————————————————————————————
TROUBLESHOOTING
If the machine stops operating correctly, check the following possible problems before requesting service. You can solve most problems by yourself. If you need additional help, the Brother Solutions Center offers the latest FAQs and troubleshooting tips. Visit us at [http://solutions.brother.com]. If the problem persists, contact your dealer or the nearest authorized service center.
Symptom Possible cause How to put it right Reference The machine is not plugged in. Plug the machine in. page 10 The main power switch is turned off. Turn on the main power switch. page 10 The sewing machine does The bobbin winder shaft is pushed to Move the bobbin winder shaft to the page 13 not work. the right. left.
You have not used the foot control- Use the foot controller properly. page 11 ler properly.
You have not inserted the needle Insert the needle properly. page 20 properly.
The needle clamp screw is loose. Use the screwdriver to firmly tighten page 21 the screw. The needle is bent or blunt. Replace the needle. page 20
You have not used the right combi- Choose a thread and needle that are page 19 nation of fabric, thread and needle. appropriate for the type of fabric.
The presser foot you are using is not Attach the presser foot that is correct page 35, 36, appropriate for the type of stitch that for the type of stitch that you want to 38, 40, 41 you want to sew. sew. The upper thread tension is too tight. Loosen the upper thread tension. page 28 The needle breaks. You are pulling the fabric too much. Lightly guide the fabric. – The area around the hole in the nee- Replace the needle plate. dle plate is scratched. Contact your retailer or the nearest – authorized service center.
The area around the hole in the Replace the presser foot. Contact your retailer or the nearest – presser foot is scratched. authorized service center. Replace the bobbin case. The bobbin case is scratched. Contact your retailer or the nearest – authorized service center.
You have not used a bobbin that has Incorrect bobbins will not work been designed for this machine. properly. Only use a bobbin that has page 12 been designed for this machine. You have not threaded the upper thread properly. (for example, you have not fitted the spool properly, or Correct the upper threading. page 16 the thread has come out of the guide above the needle.)
There are knots or tangles in the Remove any knots or tangles. – The upper thread. thread breaks. The needle is not appropriate for the Choose a needle that is appropriate page 19 thread you are using. for the type of stitch. The upper thread tension is too tight. Loosen the upper thread tension. page 28 Remove the tangle thread. If the The thread is tangled, for example, thread is tangled in the shuttle race, page 46 in the shuttle race. clean the shuttle race.
50 LS2125_Appendix.fm Page 51 Friday, February 29, 2008 10:20 AM
Symptom Possible cause How to put it right Reference The needle is bent or blunt. Replace the needle. page 20
You have not inserted the needle Insert the needle properly. page 20 properly.
The area around the hole in the nee- Replace the needle plate. dle plate is scratched. Contact your retailer or the nearest – authorised service center.
The upper The area around the hole in the Replace the presser foot. thread breaks. Contact your retailer or the nearest – presser foot is scratched. authorised service center.
The bobbin case is scratched, or has Replace the bobbin case. a burr on it. Contact your retailer or the nearest – authorised service center. Incorrect bobbins will not work You have not used a bobbin that has properly. Only use a bobbin that has page 12 been designed for this machine. been designed for this machine. You have not wound the bobbin thread properly. Wind the bobbin thread properly. page 12 The bobbin is scratched or does not turn smoothly. Replace the bobbin. – 4 The lower Remove the tangled thread and thread is tangled The thread is tangled. clean the shuttle race. page 46 or breaks. Incorrect bobbins will not work You have not used a bobbin that has been designed for this machine. properly. Only use a bobbin that has page 12 been designed for this machine. Bobbin is set incorrectly. Reset the bobbin thread correctly. page 14 The thread is tangled on the The upper thread was not threaded wrong side of correctly. Correct the upper threading. page 16 the fabric. You have not threaded the upper thread properly. Correct the upper threading. page 16 You have not wound the bobbin thread properly. Wind the bobbin thread properly. page 12 You have not used the right combination of fabric, thread and Choose a thread and needle that are page 19 needle. appropriate for the type of fabric. The thread ten- You have not attached the presser- Attach the presser-foot holder prop- sion is incorrect. foot holder properly. erly. page 24 Adjust the tension of the upper The thread tension is incorrect. thread. page 28 Incorrect bobbins will not work You have not used a bobbin that has been designed for this machine. properly. Only use a bobbin that has page 12 been designed for this machine. Bobbin is set incorrectly. Reset the bobbin thread correctly. page 14
The upper The bobbin thread is incorrectly thread is too installed. Correctly install the bobbin thread. page 14 tight.
51 LS2125_Appendix.fm Page 52 Tuesday, February 26, 2008 2:59 PM
APPENDIX ——————————————————————————————————————————————————————————
Symptom Possible cause How to put it right Reference
You have not threaded the upper Thread the upper thread and wind thread properly or fitted the bobbin the bobbin thread properly. page 14, 16 properly.
You have not fitted the spool prop- Fit the spool properly. – erly. You have not used the right The fabric is Choose a thread and needle that are combination of fabric, thread and appropriate for the type of fabric. page 19 wrinkled. needle. The needle is bent or blunt. Replace the needle. page 20
If you are sewing thin fabric, the Sew with stabiliser material under page 31 stitch is too thick. the fabric.
The thread tension is incorrect. Adjust the tension of the upper page 28 thread.
You have not threaded the upper Correct the upper threading. page 16 thread properly.
You have not used the right combi- Choose a thread and needle that are page 19 nation of fabric, thread and needle. appropriate for the type of fabric. Stitches are skipped. The needle is bent or blunt. Replace the needle. page 20 You have not inserted the needle Insert the needle properly. properly.
Dust has accumulated under the Remove the needle plate cover and page 46, 47 needle plate or in the shuttle race. clean the plate and the shuttle race.
Dust has built up in the feed dogs or Clean the shuttle race. page 46 in the shuttle race.
You have not threaded the upper Correct the upper threading. page 16 thread properly. Replace the bobbin case. The bobbin case is scratched. Contact your retailer or the nearest – There is a high- authorized service center. pitched noise while sewing. Incorrect bobbins will not work You have not used bobbin that has properly. Only use a bobbin that has page 12 been designed for this machine. been designed for this machine. Make sure to oil the machine once a week if you use it more than an hour Insufficient oiling. page 45 a day. If you use it more often, oil every day.
The presser foot that you are using is Attach the presser foot that is correct page 33, 36, not correct for the type of stitch. for the type of stitch that you want to 38, 40, 41 sew.
The stitch is not The thread tension is incorrect. Adjust the tension of the upper page 28 sewn correctly. thread. Remove the tangle thread. If the The thread is tangled, for example, in the shuttle race. thread is tangled in the shuttle race, page 46 clean the shuttle race. You have not used the right combi- Choose a thread and needle that are nation of fabric, thread and needle. appropriate for the type of fabric. page 19 The fabric does Remove the tangle thread. If the not feed. The thread is tangled, for example, in the shuttle race. thread is tangled in the shuttle race, page 46 clean the shuttle race. The sewing light bulb does not The sewing lamp is damaged. Change the sewing light bulb. page 45 come on.
52 LS2125.book Page 53 Tuesday, February 26, 2008 1:43 PM
INDEX
A S accessories ...... 9 satin stitching ...... 32 appliqués ...... 41 seam ripper ...... 37 B sewing machine needles ...... 19 basic stitching ...... 33 shell tuck stitching ...... 43 shuttle hook removal ...... 47 blind hem stitching ...... 33 bobbin ...... 14 shuttle race cleaning ...... 47 , 16 bobbin case ...... 14 spool pin ...... 12 straight stitch ...... 33 bobbin winder ...... 12 stretch blind stitch ...... 33 button sewing ...... 38 stretch fabrics ...... 31 buttonhole foot ...... 36 buttonhole sewing ...... 36 T C thick fabrics ...... 30 thin fabrics ...... 31 cleaning ...... 46 thread cutter ...... 28 D thread guide ...... 16 darning ...... 35 thread tension ...... 28 E trial sewing ...... 30 embroidering ...... 41 troubleshooting ...... 50, extra spool pin ...... 22 twin needle ...... 21 22 U F , , feed dogs ...... 8, 47 upper tension-control dial ...... 28 29 48 flat bed attachment ...... 8, 31 upper threading ...... 16 foot controller ...... 27 W free-arm style ...... 31 winding the bobbin ...... 12 G Z gathering ...... 43 zigzag stitches ...... 30, 32, 41 H zipper foot ...... 40 handwheel ...... 7 zipper insertion ...... 40 J joining ...... 44 M main parts ...... 6 main power switch ...... 10 monogramming ...... 41 N needle ...... 19 needle bar thread guide ...... 8 needle clamp screw ...... 8, 21 needle plate ...... 8, 47 O oiling ...... 45 overcasting stitches ...... 32 P pattern selection dial ...... 6, 26 presser foot ...... 8, 23 presser foot holder ...... 8, 24 presser foot lever ...... 7, 16 pre-tension disk ...... 12 R relative chart of sewing fabrics, needles and threads .....19 repacking ...... 48 reverse sewing lever ...... 28
53 LS-2125_brother_cover_Eng K
KNOWING YOUR SEWING MACHINE
SEWING BASICS
UTILITY STITCHES
APPENDIX
Basic Sewing and Mending Machine Operation Manual English XE4592-001 Please visit us at http://solutions.brother.com where you can get product support and answers to frequently Printed in China asked questions (FAQs).