DOCSLIB.ORG

Type N Amphenol®

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Type N Amphenol® Type N Amphenol® Description Named for Paul Neill of Bell Labs and developed in the 1940’s. The Type N offered the first true microwave performance. Type N connector was developed to satisfy the need for a durable, weatherproof medium size RF connector with consistent performance through 11 GHz. There are two families of Type N connectors: • Standard N (Coaxial Cable) • Helical N (Corrugated Cable) Primary applications are the termination of medium to miniature size coaxial cable: RG-8 and RG-225 RG-58 and RG-141 Type N Specifications 226 Features/Benefits • Accommodates a wide range of medium to Cable Plugs 227 miniature sized RG coaxial cables in a rugged Right Angle Plugs 228 medium size design. Provides customer flexibility Jacks 229-232 in their design and manufacturing with a durable Receptacles, Accessories 234-235 connector. Adapters 236 • Broad line of Military (M39012 prefix), Industrial (UG prefix), and Commercial Grade (RFX suffix) products available. Gives customer choices in Helical N Corrugated weighing cost versus performance benefits. Cable Connectors N Type • Available in many styles: Plugs (Straight and Specifications 239 Right Angle) and Jacks (Panel Mount, Bulkhead Plugs 240-241 Mount, Receptacle). Meets many customer application demands. Jacks 242-243 Application • Antennas • Radar • Base Stations • Radios • Broadcast • Satcom • Cable Assemblies • Surge Protection • Components • WLAN • Instrumentation • Mil-Aero Amphenol Corporation Tel: 800-627-7100 www.amphenolrf.com 225 Type N Amphenol® Specifications ELECTRICAL MECHANICAL ENVIRONMENTAL Impedance 50 ohms Mating 5/8-24 threaded Temperature range TFE -65°C to + 165°C Frequency range 0-11 GHz coupling Copolymer of Styrene: - 55°C to + 85°C Voltage rating 1,500 volts peak Cable affixment All crimps: hex braid (braid or jacket) crimp. Weatherproof All series N with gaskets Dielectric 2,500 volts rms. Clamps: screw- are weatherproof withstanding voltage thread nut and braid Hermetic seals Pass helium leak test of VSWR (MIL-C-39012 M39012 straight clamp 2 X 10-8 cc/sec cable connectors) connectors: Cable affixment Crimp: crimp or solder 1.3 max. 0-11 GHz Pressurized Compression seal (center conductor) All others: solder only Shock MIL-Std. 202 method M39012 right angle: Captivated All crimps. Others, 213 1.35 max. 0-11 GHz contact where specified. Vibration MIL-Std. 202 method Other Contact resistance: Cable retention Crimps: 60-120 lbs. 204 (test cond. B) center contact 1.0 Clamps: 30-70 lbs. milliohm Moisture resistance MIL-Std. 202 method 106 outer contact 0.2 MATERIAL milliohm Corrosion MIL-Std. 202 method 101 (test cond. B) RF leakage: -90 dB Contacts Male: brass; Female: minimum at 3 GHz phosphor bronze or Temperature MIL-Std. 202 method cycling 102 (test cond. C) Insertion loss: .15 dB beryllium copper. Silver maximum at 10 GHz or gold plated Altitude MIL-Std. 202 method 105 (test cond. C) Insulation resistance: Other metal parts Brass: 5000 megohms ASTROplate® finish minimum except M39012 silver. MILITARY SPECIFICATIONS Insulators TFE, copolymer of styrene or glass-TFE MIL-C-39012 & Where applicable (hermetic seal) MIL-A-55339 Weatherproof Silicone rubber or gaskets synthetic rubber NOTE: These characteristics are typical and may not apply to all connectors. Crimp ferrule Copper PLUG JACK REF PLANE .412/.398 .362/.356 .060/.016 REF PLANE .207/.187 .230/.210 .625-24UNEF-2A .210 MIN Å.827 MAX Å.330 MAX Å.630 MIN Å.344/.336 Å.627 MAX Å.320/.316 "N" SOCKET (FILE: NSOC.DWG) .077/.047 .077/.047 SEALING GASKET .168/.158 .202/.172 FULL THD. .625-24UNEF-2B .177 MIN FULL THD. .422 MIN "N" PIN .210 REF PLANE (FILE: NPIN.DWG) MIN .140/.110 .003 MIN .066/.063 Amphenol Corporation Tel: 800-627-7100 www.amphenolrf.com 226 Type N Amphenol® Cable Attachment Method Fig. 1 Fig. 2 a I c• a c• b b Crimp-Crimp N Plugs Clamp N Plugs 82-332 82-4425-1003 82-5370 82-202 34025 82-340 82-4426 82-5375 82-202-RFX 34025-RFX 82-340-1052 82-4426-11RFX 82-5375-RFX 82-3202 82-202-1006 82-340-1054 82-4427 82-5380-RFX 82-4425 82-4427-1006 82-6152 82-312 82-6034 Fig. 3 a Fig. 4 a c• b c b Solder-Solder N Plugs Crimp-Crimp N Plugs 82-5955-RFX 82-6142-1000 82-6106 82-5956-RFX 82-5993 82-6010 82-6124 N CABLE PLUGS N Type Cable Attachment Dimensions, inches (millimeters) Construction Notes Military Amphenol Cable RG-/U Fig. Outer Inner a b c G CAI Plt. Ins. Number Number 8, 213 Crimp Crimp 1.48(37.7)I .827(21.0) .418(10.6) C11 P33 D1 Lockwire Holes M39012/01B0007 82-340 1 L 8, 9, 144, 165, 213 Clamp Solder 1.50(38.1) .827(21.0) .444(11.3) C8 P1 D9 Lockwire HolesUG-21E/U 82-3202 2 Clamp Solder 1.50(38.1) .827(21.0) .444(11.3) C8 P1 D1 Captivated Cont. UG-1185/U 82-312 2 L 8, 9, 144, 165, 213, Clamp Solder 1.50(38.1) .827(21.0) .444(11.2) C8 P1 D1 Lockwire Holes UG-21D/U 82-202 2 L 214, 216, 225 Clamp Solder 1.50(38.1) .827(21.0) .437(11.1) C8 P7 D1 — 82-202-RFX 2 L 9, 214 Crimp Crimp 1.48(37.7)I .827(21.0) .438(11.1) C11 P34 D1 Lockwire Holes M39012/01B0008 82-332 1 9, 214, 225, 393 Crimp Crimp 1.54(39.1)I .827(21.0) .438(11.1) C11 P15 D1 — — 82-4425-1003 1 55, 142, 223 Crimp Crimp 1.37(34.9)I .827(21.0) .220(5.6) C11 P15 D1 Lockwire Holes — 82-5370 1 L 58, 141 Crimp Crimp 1.48(37.7)I .827(21.0) .206(5.2) C11 P17 D1 Lockwire Holes — 82-5375 1 L Crimp Crimp 1.36(34.6)I .827(21.0) .210(5.3) C11 P7 D1 — — 82-5375-RFX 1 L N Type 58, 141, 142A, 400 Clamp Solder 1.38(34.9) .827(21.0) .219(5.4) C8 P1 D1 Lockwire Holes UG-536B/U 34025 2 L Clamp Solder 1.31(33.2) .827(21.0) .212(6.4) C8 P7 D1 — — 34025-RFX 2 L 142, 142B, 400 Crimp Crimp 1.38(35.0)I .827(21.0) .220(5.6) C11 P15 D1 — — 82-4427-1006 1 142, 400 Crimp Crimp 1.45(36.9)I .827(21.0) .220(5.6) C11 P34 D1 Lockwire Holes M39012/01-0503 82-4427 1 L 213 Crimp Crimp 1.45(36.9)I .827(21.0) .418(10.6) C11 P34 D1 Lockwire Holes M39012/01-0502 82-4426 1 214, 225, 393 Crimp Crimp 1.45(36.9)I .827(21.0) .438(11.1) C11 P33 D1 Lockwire Holes M39012/01-0501 82-4425 1 L Belden 9913, 9914 Crimp Crimp 1.48(37.7)I .827(21.0) .418(10.6) C11 P15 D1 — — 82-340-1052 1 B9913, Amph TWB 4001 Clamp Solder 1.50(38.1) .827(21.0) .443(11.2) C8 P1 D1 — — 82-202-1006 2 L LMR400, TWB 4001 Crimp Crimp 1.49(37.8)I .850(21.6) .418(10.6) C11 P1 D9 Hex Coupling — 82-6142-1000 3 LMR600, TWB 6001 Crimp Crimp 1.98(50.3)I .930(23.6) .625(15.9) C11 P34 D9 Hex Coupling — 82-5993 3 LMR240, TWB 2401 Crimp Crimp 1.41(35.8)I .850(21.6) .261(6.6) C11 P15 D1 Hex Coupling — 82-6106 3 LMR240, TWB 2401 Crimp Preassy 1.41(35.8)I .850(21.6) .261(6.6) C11 P34 D1 Hex Coupling — 82-6010 3 59, 62 Crimp Crimp 1.36(34.6)I .827(21.0) .261(6.6) C11 P7 D1 — — 82-5380-RFX 1 174, 188, 316 Crimp Crimp 1.41(35.8)I .827(21.0) .125(3.2) C11 P7 D1 — — 82-6034 3 LMR 240, TWB2401 Crimp Crimp 1.17(29.8) .827(21.0) .220(5.6) C11 P7 D1 — — 82-6152 1 402 (.141 S/R) Solder Solder 1.19(30.3) .826(21.0) .141(3.6) C9 P7 D1 — — 82-5955-RFX 4 405 (.086 S/R) Solder Solder 1.19(30.3) .826(21.0) .086(2.2) C9 P7 D1 — — 82-5956-RFX 4 401 (.250 S/R) Solder Solder 1.19(30.3) .826(21.0) .250(6.35) C9 P7 D1 — — 82-6124 4 Ethernet®M Cables Times AA4478(FEP), AA4479(PVC); Belden Crimp Crimp 1.48(37.7)I .827(21.0) .437(11.1) C11 P7 D1 — — 82-4426-11RFX 1 89880(FEP), 9880(PVC) G accommodates cable diameter includes outer ferrule Ethernet = Xerox Trademark Distributor stocked Amphenol Corporation Tel: 800-627-7100 www.amphenolrf.com 227 Type N Amphenol® Right Angle Plugs Fig. 1 c• d a b Crimp N Angle Plugs 82-4440-1001 82-5995 82-5374 82-4440 Fig. 2 Fig. 3 a d a b d c• b c Crimp N Angle Plug Cubic Body 82-6048-1000 Clamp N Angle Plug 82-5989-1004 Cubic Body 82-6157 18750 82-6165 82-5988-1000 82-6166 N RIGHT ANGLE PLUGS Cable Attachment Dimensions, inches (millimeters) Notes Military Amphenol Cable RG-/U Fig. Outer Inner a b c G d CAI Plt. Ins. Number Number 9, 214, 225, 393 Crimp Crimp 1.40(35.5) .827(21.0) .437(11.1) 1.95(49.5)I C11 P28 D1 — 82-4440-1001 1 55, 142, 223 Crimp Crimp 1.41(35.7) .827(21.0) .220(5.6) 1.98(50.2)I C11 P11 D1 — 82-5374 1 L 58, 141, 142 Clamp Solder 1.63(41.3) .827(21.0) .210(5.3) 1.22(31.0) C8 P1 D1 — 18750 2 214, 225, 393 Crimp Crimp 1.40(35.5) .827(21.0) .438(11.1) 1.95(49.5)I C11 P33 D1 M39012/05-0501 82-4440 1 L 214, 393 Crimp Solder 1.195(30.4) .827(21.0) .438(11.1) 1.62(4.1)I C11 P33 D9 — 82-5988-1000 2 214, 393 Crimp Solder 1.195(30.4) .850(21.6) .438(11.1) 1.62(4.1)I C11 P33 D9 Hex Coupling 82-5988-1004 3 LMR 600, TWB 6001 Crimp Solder 1.32(33.5) .850(21.6) .625(15.9) 1.61(40.9)I C11 P34 D9 Hex Coupling 82-5995 1 Amph TWB 4001, Crimp Solder 1.291(32.8) .850(21.6) .298(7.57) 1.594(40.5)I C11 P33 D9 — 82-6048-1000 3 LMR 400, Belden 9913 LMR 240, 8X Crimp Crimp 1.43(36.5) .827(21.0) .259(6.6) 1.07(27.2) C11 P7 D1 Nickel Body 82-6157 3 LMR 240, 8X Crimp Crimp 1.43(36.5) .827(21.0) .259(6.6) 1.07(27.2) C11 P7 D1 Nickel Body 82-6165 3 LMR 240, 8X Crimp Crimp 1.43(36.5) .827(21.0) .259(6.6) 1.07(27.2) C11 P33 D1 Silver Body 82-6166 3 G accommodates cable diameter includes outer ferrule Distributor stocked Amphenol Corporation Tel: 800-627-7100 www.amphenolrf.com 228 Type N Amphenol® Straight Jacks Fig.
Load more

Recommended publications
  • Amphenol Connex
    Our Products ----------------------- Search Results for: Straight Crimp Jack - Captive Contact 7/16 Please note: Images are for reference only BNC D-Sub FME Part Number: 172207 Cable Group: 17 MCX Family/Series: Type N Coaxial Finish: Nickel MMCX Connectors Insulation: Teflon SMA Product Type: CRIMP/SOLDER Impedance: 50 ohms SMB ATTACHMENTS FOR FLEXIBLE AND Crimp Tool: .610 HEX SMC SEMI-RIGID CABLE TNC Description: Straight Crimp Jack - Twin BNC Captive Contact Cable: LMR 600 ** Type F Type N Add to Cart | Product Specs | Customer Drawing UHF ----------------------- Between-Series Adapters Shielded Terminations Strain-Relief Boots Tools ----------------------- View All Products Copyright © 2001 - 2008 Amphenol Connex. All rights reserved. Copyright | Terms & Conditions | Contact Us | Amphenol.com Our Products ----------------------- 7/16 Features & Benefits | Applications | Standard Specs | Corrugated Specs | Assembly Instructions BNC D-Sub Named after Paul Neill of Bell Labs after being developed in the 1940's, the FME Type N offered the first true microwave performance. The Type N connector MCX was developed to satisfy the need for a durable, weatherproof, medium-size MMCX RF connector with consistent performance through 11 GHz. SMA SMB There are two families of Type N connectors: Standard N (coaxial cable) and SMC Corrugated N (helical and annular cable). Their primary applications are the TNC termination of medium to miniature size coaxial cable, including RG-8, RG- Twin BNC 58, RG-141, and RG-225. RF coaxial connectors are the most important Type F element in the cable system. Corrugated copper coaxial cables have the Type N potential to deliver all the performance your system requires, but they are often limited by the UHF performance of the connectors.
    [Show full text]
  • Connectors, Air Lines and RF Impedance
    The IEE Measurement, Sensors, Instrumentation and NDT m Professional Network Connectors, Air Lines and RF Impedance N M Ridler, NPL 0 Crown Printed and published by the IEE, Michael Faraday House, Six Hills Way, Stevenage, Herts SG1 ZAY, UK Abstract This lecture will give information on -impedance considerations for measurements at RF and microwave frequencies. The subject matter is divided into three areas: m . Coaxial connectors used to perform precision transmission line measurements e Air lines used to define characteristic impedance in coaxial line Special considerations needed when defining impedance and using impedance concepts ai: RF-: I About the Speaker Nick Ridler graduated from King’s College, University of London, in 1981. He then spent seven years working in industry on high power microwave oscillators and amplifiers before joining the RF and Microwave Standards Division at the Royal Signals and Radar Establishment, Great Malvern. This Division later transferred to the National Physical Laboratory (NPL) in Teddington. Mr Ridler is currently responsible for NPL’s RF and microwave impedance activities, in the Division of Enabling Metrology, which includes managing the primary national standard facilities for vector network analyser measurements, His current research interests include: establishing impedance traceability at RF; millimetre-wave on-wafer measurements; uncertainty estimation techniques for vector measurements; and, using the Internet to provide traceability for measuring instruments at locations remote to NPL. Connectors, Air Lines and FtF Impedance R = series resistance, per unit length, for a coaxial line including conductor loss (l2.m-l). o = conductivity of an air line's conductors (S.m-'). v = speed of the electromagnetic wave in the air line N M Ridler (v = CA&, (m.s*')).
    [Show full text]
  • Optimize Your RF/MW Coaxial Connections Dave Mcreynolds Director of Engineering RF Industries
    Optimize Your RF/MW Coaxial Connections Dave McReynolds Director of Engineering RF Industries /microwave connectors are small and often overlooked, but they serve as gateways for many RF electronic devices and systems, linking components and systems together to enable proper operation. Coaxial connectors are often taken for granted—until they fail. They are instrumental to the operation of many electronic devices and systems, from cellular telephones and wireless data networks to the most advanced radar and electronic-warfare (EW) systems. Whether designing or simply maintaining electronic devices and systems, understanding the role of the RF/microwave connector can help to boost both performance and reliability. Before exploring technical details about connectors, it might help to review some of their history. Connectors come in many shapes and sizes. They are used in a variety of electronic devices, from audio through millimeter-wave frequencies. The interface dimensions, machine tolerances, materials, even the plating and finish on those materials, all contribute to how well and how reliably a connector performs. Coaxial connectors are designed for mounting on the end of coaxial cables, on printed-circuit boards (PCBs), on panels, and on many different electronic component and device packages. Why there are so many different types of coaxial connectors and adapters is largely a matter of RF/microwave history and the evolution of high-frequency technology. With the evolving demands of higher-frequency applications, connector developers are pushed to achieve ever higher frequencies, smaller footprints, unique interfaces, and better performance with their designs. Anyone who has assembled a cable-television (CATV) system, with its F-type connector/cable assemblies, will appreciate the convenience of an electrical connector without necessarily being aware of its electrical and mechanical benefits.
    [Show full text]
  • Coaxial Connectors Adapters and Connectors
    Coaxial Connectors Adapters and Connectors Overview Many coaxial connector types are available in the RF and microwave industry, each designed for a specific purpose and application. For measurement applications, it is important to consider the number of connects/disconnects, which impact the connector’s useful life. The frequency range of any connector is limited by the excitation of the first circular waveguide propagation mode in the coaxial structure. Decreasing the diameter of the outer conductor increases the highest usable frequency; filling the air space with dielectric lowers the highest usable frequency and increases system loss. Performance of all connectors is affected by the quality of the interface for the mated pair. If the diameters of the inner and outer conductors vary from the nominal design, if plating quality is poor, or if contact separation at the junction is excessive, then the reflection coefficient and resistive loss at the interface will be degraded. A few connectors, such as the APC-7, are designed to be sexless. Most are female connectors that have slotted fingers. The fingers need to accommodate a male pin with diameter variations. As a result, it introduces contact point and impedance variations and hence reduced repeatability and reliability. Keysight Technologies, Inc. offers slotless versions of connectors in certain measuring products, that decrease impedance and contact point variations. Find us at www.keysight.com Page 1 The following is a brief review of common connectors used in test and measurement applications: APC-7 (7 mm) connector The APC-7 (Amphenol Precision Connector-7 mm) offers the lowest reflection coefficient and most repeatable measurement of all 18 GHz connectors.
    [Show full text]
  • Amphenolrf.Com
    ® Amphenol RF Military-Aerospace Market RF components perform vital functions in mission-critical systems for military aerospace. Such products require superior performance and reliability under conditions of stress and in hostile environments. High performance environmental connectors are generally used to interconnect electronic and fiber optic systems in sophisticated aerospace, military, commercial and industrial equipment. Amphenol RF is recognized as a leading supplier in the Military- Aerospace industry for its quality MIL-C-39012 interconnect products and innovative solutions. Applications: • Remote Control Systems • Antenna Systems • Aircraft Radio • Tactical Radio Programs • Communications Systems • Joint Strike Fighter • Interrogation Systems • Gang or Blind Mate high power systems Our Products: AFI The AFI connector interface utilizes a proprietary configuration that allows for industry leading “float” to compensate for the axial and radial misalignment due to packaging tolerances. This industry- leading float results in a maximum misalignment allowed by the system of .030” [0,8 mm] radial and .040” [1,0 mm] axial. The interface is available in both 75 Ω and 50 Ω configurations. Blind Mate Type-N Adapter (M/F) The Blind Mate Type-N Adapter allows for the blind mating of multiple “N” connectors in a rack and panel design. The floating mounting system compensates for axial and radial misalignment. This connector provides excellent electrical performance from 0 to 6 GHz. MCX While the MCX uses identical inner contact and insulator dimensions as the SMB, the outer diameter of the plug is .140 inches, which is 30% smaller than the SMB. This series provides designers with options where weight and physical space are limited.
    [Show full text]
  • RF Connectors 50 Ohm Catalog
    Electronic Components Customer Support Locations ASIA Tuopandun Industrial Area, Jinda Cheng, Xiner Village, Shajing Town, Baoan District, Shenzhen City, Guangdong, China 518125 Tel: +86 755 2726 7238 Cannon 50 Ohm Fax: +86 755 2726 7515 RF Connectors GERMANY Cannonstrasse 1 Weinstadt, 71364 Tel: +49.7151.699.0 Fax: +49.7151.699.217 ITALY Corso Europa 41/43 Lainate (MI), Italy 20020 Tel: +39.02938721 Fax: +39.0293872300 UK Jays Close, Viables Estate Basingstoke, Hants, RG22 4BA Tel: +44.1256.311200 Fax: +44.1256.323356 USA 100 New Wood Road Watertown, CT 06796 Tel: 860.945.0206 Toll Free: 800.683.7666 Fax: 860.645.0303 www.ittcannon.com ©2007 ITT Corporation. “Engineered for life” and “Cannon” are registered trademarks of ITT Corporation. Specification and other data are based on information available at the time of printing, and are subject to change without notice. 50 RF Apr-07 Over 90 year history ... ITT's Electronic Components business (www.ittcannon.com) is an international supplier of connectors, interconnects, cable assemblies, I/O card kits and smart ITT Electronic Components is an innovative and dynamic company with card systems. As a worldwide leader in connector technology for nearly a the in-depth experience of a 90 plus year industry leader. We are part of century, ITT offers one of the industry's broadest product offerings, ITT Corporation, a multi-disciplined, multi-national company engaged in manufacturing capability worldwide, fast time to market, high volume/high the design and manufacture of electronic components, defense products yield capacity, robust design and Value-Based Product Development and an and fluid handling controls.
    [Show full text]
  • Coaxial Cable
    ANALOG ELECTRICAL and DIGITAL VIDEO FORMATS and CONNECTORS Analog Electrical Formats/Connectors Component Video Component video is a type of video information that is transmitted or stored as two or more separate signals (as opposed to composite video, such as NTSC or PAL, which is a single signal). Most component video systems are variations of the red, green and blue signals that make up a television image. The simplest type, RGB, consists of the three discrete red, green and blue signals sent down three wires. This type is commonly used in Europe through SCART connectors. Outside Europe, it is generally used for computer monitors, but rarely for TV-type applications. Another type consists of R-Y, B-Y and Y, delivered the same way. This is the signal type that is usually meant when people talk of component video today. Y is the luminance channel, B-Y (also called U or Cb) is the blue component minus the luminance information, and R-Y (also called V or Cr) is the red component minus the luminance information. Variants of this format include YUV, YCbCr, YPbPr and YIQ. In component systems, the synchronization pulses can either be transmitted in one or usually two separate wires, or embedded in the blanking period of one or all of the components. In computing, the common standard is for two extra wires to carry the horizontal and vertical components, whereas in video applications it is more usual to embed the sync signal in the green or Y component. The former is known as sync-on-green.
    [Show full text]
  • MICROWAVE COAXIAL CONNECTOR TECHNOLOGY: a CONTINUING EVOLUTION Mario A
    MAURY MICROWAVE 13 Dec 2005 CORPORATION Originally published as a Feature Article in the Microwave Journal 1990 State of the Art Reference, September 1990; Updated December 2005 MICROWAVE COAXIAL CONNECTOR TECHNOLOGY: A CONTINUING EVOLUTION Mario A. Maury, Jr. Maury Microwave Corporation (a) Introduction Coaxial connectors are one of the fundamental tools of microwave technology and yet they appear to be taken for granted in many instances. Unfortunately, many engineers tend to overlook the lowly connec- tor with resulting performance compromises in their applications. A good understanding of connectors, both electrically and mechanically, is required to utilize them properly and derive their full benefit. It should be remembered that performance starts at the (b) connector. Figure 1: Precision coaxial connectors in use today; Coaxial connectors provide a means to connect and (a) 7mm and 14mm sexless connectors and (b) 3.5mm female disconnect transmission lines, components and sys- and male, type N female and male. tems at microwave frequencies. They allow accessing circuits, modularizing, testing, assembling, inter- This paper provides a brief history of coaxial connec- connecting and packaging components into systems. tors, gives an overview of coaxial connector technology today, cites sources of further informa- There is a broad variety of coaxial connectors avail- tion and takes a look into the future as connectors able today due to the various design trade-offs and continue to evolve. applications that exist at microwave frequencies, including impedance (usually 50 ohms), frequency IEEE P287 Committee of operation, power handling, insertion loss, reflec- tion performance, environmental requirements, size, In 1988, the sub-committee P287 for precision co- weight and cost.
    [Show full text]
  • Ethernet - Wikipedia, the Free Encyclopedia Página 1 De 12
    Ethernet - Wikipedia, the free encyclopedia Página 1 de 12 Ethernet From Wikipedia, the free encyclopedia The five-layer TCP/IP model Ethernet is a family of frame-based computer 5. Application layer networking technologies for local area networks (LANs). The name comes from the physical concept of DHCP · DNS · FTP · Gopher · HTTP · the ether. It defines a number of wiring and signaling IMAP4 · IRC · NNTP · XMPP · POP3 · standards for the physical layer, through means of SIP · SMTP · SNMP · SSH · TELNET · network access at the Media Access Control RPC · RTCP · RTSP · TLS · SDP · (MAC)/Data Link Layer, and a common addressing SOAP · GTP · STUN · NTP · (more) format. 4. Transport layer Ethernet is standardized as IEEE 802.3. The TCP · UDP · DCCP · SCTP · RTP · combination of the twisted pair versions of Ethernet for RSVP · IGMP · (more) connecting end systems to the network, along with the 3. Network/Internet layer fiber optic versions for site backbones, is the most IP (IPv4 · IPv6) · OSPF · IS-IS · BGP · widespread wired LAN technology. It has been in use IPsec · ARP · RARP · RIP · ICMP · from the 1990s to the present, largely replacing ICMPv6 · (more) competing LAN standards such as token ring, FDDI, 2. Data link layer and ARCNET. In recent years, Wi-Fi, the wireless LAN 802.11 · 802.16 · Wi-Fi · WiMAX · standardized by IEEE 802.11, is prevalent in home and ATM · DTM · Token ring · Ethernet · small office networks and augmenting Ethernet in FDDI · Frame Relay · GPRS · EVDO · larger installations. HSPA · HDLC · PPP · PPTP · L2TP · ISDN
    [Show full text]
  • RF Connector Solutions
    RFRF ConnectorConnector SolutionsSolutions Connecting Innovation to Application® Winchester Electronics was established in 1941 series. This long-trusted RF KINGS® Brand is and is today a global leader in the design, highly regarded by customers in the Broadcast, development, and deployment of interconnect Telecommunications, and Commercial and technology. Headquartered in Middlebury, Military Aviation industries. Connecticut, USA, Winchester operates With over 125 years of collective industry worldwide with modern, electronically linked experience, Winchester Electronics and the design, manufacturing, sales, and distribution KINGS® Brand create value for our customers facilities in the United States, Mexico, China, and by offering a proven combination of quality Malaysia. products, efficient manufacturing, dedicated Winchester’s competitive advantage is our ability service, and inventive design solutions. to solve even the most difficult interconnect In addition to the KINGS® Brand RF Connectors, problems, deploy design solutions globally to Winchester Electronics also manufactures a wide meet the customer’s manufacturing needs, variety of PCB and Power Connectors, as well as and offer true supply chain management value-added cable and electromechanical techniques to deliver value through our assemblies for customers in the Wireless high-mix, low-volume manufacturing Infrastructure, Computer, Industrial, and Medical model. Our global IT infrastructure Equipment industries. and worldwide communication capabilities allow for continuous Realizing its responsibility to the environment, information access in support of every Winchester Electronics facility is customer opportunities. The ISO Certified and all of our products are acquisition of Kings Electronics manufactured in compliance with the European expanded our technological Union RoHS directive. capabilities and broadened our market base and Providing superior products built to stringent product offering.
    [Show full text]
  • RF and Microwave Connector Care
    Instruction Sheet RF and Microwave Connector Care Inspection and Cleaning Protection from ESD Pin Depth Measurement Proper Connecting Methods Protection from Over-power and Over-voltage Connector Torque Settings and Tools Anritsu Company Part Number: 10100-00031 490 Jarvis Drive Revision: C Morgan Hill, CA 95037-2809 Published: January 2021 USA Copyright 2018 Anritsu Company TRADEMARK ACKNOWLEDGMENTS Anritsu is a trademark of Anritsu Company. V Connector, K Connector, and W1 Connector are trademarks of Anritsu Company. Acrobat Reader is a registered trademark of Adobe Corporation. NOTICE Anritsu Company has prepared this manual for use by Anritsu Company personnel and customers as a guide for the proper installation, operation and maintenance of Anritsu Company equipment and computer programs. The drawings, specifications, and information contained herein are the property of Anritsu Company, and any unauthorized use or disclosure of these drawings, specifications, and information is prohibited; they shall not be reproduced, copied, or used in whole or in part as the basis for manufacture or sale of the equipment or software programs without the prior written consent of Anritsu Company. UPDATES Updates, if any, can be downloaded from the Documents area of the Anritsu web site at: http://www.anritsu.com For the latest service and sales information in your area, please visit: https://www.anritsu.com/en-US/Contact-US/ Safety Symbols To prevent the risk of personal injury or loss related to equipment malfunction, Anritsu Company uses the following symbols to indicate safety-related information. For your own safety, please read the information carefully before operating the equipment. Connectors RM PN: 10100-00031 Rev.
    [Show full text]
  • Microwave Connectors
    Microwave Measurements: Microwave connectors Dept. of Electrical, Computer and Biomedical Engineering, University of Pavia e-mail: [email protected] web: microwave.unipv.it Microwave Measurements, L. Silvestri 1 Outline • Why do use microwave connectors? • Why are there so many different connectors? • Characteristics of some connectors’ families • Connectors care • Connector mounting Microwave Measurements, L. Silvestri 2 Why do we use microwave connectors? Connectors are used to connect devices and circuits made separately through transmission lines. DUT They are an important (sometimes decisive) in repeatability and accuracy of the measurement. Microwave Measurements, L. Silvestri 3 Why are there so many different connectors? BNC, SMB, OSMT, OSX, MCX, PCX, MMCX, SMC, SMA, TNC, N, APC-7, 7mm, OSP, 3.5mm, OSSP, SSMA, 2.92mm, K, GPO, OSMP, SMP, OS-50P, 2.4mm, 1.85mm, V, 1mm, … From: www.microwave101.com Microwave Measurements, L. Silvestri 4 Why are there so many different connectors? BNC, SMB, OSMT, OSX, MCX, PCX, MMCX, SMC, SMA, TNC, N, APC-7, 7mm, OSP, 3.5mm, OSSP, SSMA, 2.92mm, K, GPO, OSMP, SMP, OS-50P, 2.4mm, 1.85mm, V, 1mm, … Each manufacturer may use proprietary interconnect standards (i.e., specifically designed by the manufacturer). However, to ensure compatibility with circuits made by others, universally accepted connector standards are generally used. The differences are in frequency range, environment of usage, history (when they have been designed and for which reasons) etc.. Microwave Measurements, L. Silvestri 5 Families From: www.microwave101.com (slide 6 and 7) Microwave Measurements, L. Silvestri 6 Families Microwave Measurements, L. Silvestri 7 BNC BNC is an acronym from "Bayonet Neil-Concelman" or "Bayonet Navy Connector" or "Baby Neil Connector“ (it depends on the source).
    [Show full text]