Cisco BWX360 WiMAX Outdoor / engbt / 253306943 / Cover_front.fm / 07.04.2010

Cisco BWX360 WiMAX Outdoor Modem Template 2006_02_28 Template

Installation Guide

This device works in a frequency band for which a general licence might have to be obtained. Please contact your service provider or your National Authority for Frequency Management about licensing before putting this device into service.

Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / SE680WiMAXIVZ.fm / 07.04.2010

Contents Contents For your safety ...... 2 Safety precautions ...... 2 Notes on assembly instructions ...... 3 The Cisco BWX360 WiMAX Outdoor Modem ...... 4 Scope of delivery ...... 4 Schablone 2006_02_28 Connectors and LEDs ...... 6 Installing the Cisco BWX360 WiMAX Outdoor Modem . . . . 8 Choosing locations ...... 9 Setting up the antenna mast ...... 10 Protecting the mast against lightning ...... 10 Assembling the outdoor modem ...... 12 Connecting the indoor unit ...... 15 Preparing to use the Cisco BWX360 WiMAX Outdoor Modem ...... 17 Launching the user interface ...... 18 Connecting to the WiMAX network and the Internet ...... 19 Precisely aligning the antenna ...... 21 Finishing off the assembly ...... 22 Appendix ...... 23 Troubleshooting ...... 23 Specifications ...... 23 Sources ...... 24 Federal Communications Commission (FCC) Statements ...... 26 Index ...... 27

1 Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Safety.fm / 07.04.2010

For your safety For your safety

Please read the safety instructions carefully before assembly and before putting into service. Safety precautions

General safety instructions

Template 2006_02_28 Template ◆ Only pass on the Cisco BWX360 WiMAX Outdoor Modem to third parties with this user guide and the assembly instructions. ◆ The Cisco BWX360 WiMAX Outdoor Modem must only be installed and put into use by a qualified electrician in accordance with the supplied installation instructions. ◆ National laws and regulations must be considered before putting the device into service. ◆ These devices are professional IT equipment. Keep the devices beyond the reach of children.

Safety instructions for connection ◆ Only use undamaged original accessories. ◆ The outdoor modem must only be installed by a qualified electrician in accordance with the assembly instructions.

Safety precautions for the Cisco BWX360 WiMAX Outdoor Modem ◆ The operation of medical appliances may be affected. Be aware of the technical conditions in your particular environment, e.g. doctor's surgery. ◆ The Cisco BWX360 WiMAX Outdoor Modem can interfere with the functioning of medical devices such as pacemakers. Keep at least 20 cm between the devices and the pacemaker. For more information consult your doctor. ◆ Do not operate the indoor unit under the influence of direct heat sources (e.g. directly in the sun). ◆ The Cisco BWX360 WiMAX Outdoor Modem complies with the regulations on lim- iting the effect of electromagnetic fields on the general population. ◆ Do not use the devices in environments with a potential explosion hazard, e.g. auto paint shops or in a humid environment (bathroom etc.). ◆ Only clean the Cisco BWX360 WiMAX Outdoor Modem with a soft anti-static cloth.

2 Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Safety.fm / 07.04.2010

Notes on assembly instructions Notes on assembly instructions

These assembly instructions describe the assembly and operation of the individual components of the Cisco BWX360 WiMAX Outdoor Modem. The configuration of the fully installed system is discussed in the user guide that you received with the Cisco BWX360 WiMAX Outdoor Modem. ◆ Please read the assembly instructions carefully before using the devices for the first time. Template 2006_02_28 Template

3 Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Product_intro.fm / 07.04.2010

The Cisco BWX360 WiMAX Outdoor Modem The Cisco BWX360 WiMAX Outdoor Modem

Scope of delivery

◆ 1 outdoor modem with integrated antennas ◆ Assembly equipment: – Distance piece for elevation setting

Template 2006_02_28 Template – Mast bracket with fastening clamps, fastening screws and brackets ◆ Assembly accessories: – 1 RJ45 plug (Phoenix connector VS-08-RJ45-5-Q/IP67 BK) to connect the cable to the outdoor modem ◆ 1 indoor unit – 1 Ethernet cable for the internal connection to the PC, 1.8 m – 1 power supply unit ◆ 1 assembly instructions ◆ 1 user guide Depending on the installation conditions and customer requirements, you can also connect the Ethernet cable from the IN connector of the indoor unit to a standard LAN socket, and RJ45 plug (e.g. Phoenix connector VS- 08-RJ45-5-Q/IP20 BK, see "Sources" on page 24) or a patch panel.

Tools and equipment required

You will require the following tools and equipment for assembly: ◆ Antenna mast with assembly equipment (for mounting on a mast); the antenna mast must have a diameter of 2–3 inches (50.8 mm–76.2 mm) and be designed for assembling this kind of antenna. ◆ Sealing material for the wall, window or roof duct ◆ Ethernet cable (non-assembled) for the Ethernet connection to the indoor unit. For the connection of the outdoor modem to the indoor unit only use a round Ethernet cable (Ø 6.0-8.5 mm), which is approved for the outdoor use. We recommend to contact one of the manufacturers which are mentioned in the chapter "Ethernet cable" on page 24. ◆ RJ45 plug (Phoenix) for the connections required indoors. Also a standard CAT5e Ethernet cable for connecting indoor units to the PC or . ◆ LSA+ wall connection socket, feeder tool and standard CAT5e Ethernet cable, if you wish to connect the Ethernet cable from outside to a wall connection socket. ◆ Cable clamps and cable ties for attaching the Ethernet cable to the antenna mast, the wall bracket and other outdoor and indoor areas ◆ Ground cable for earthing (grounding) the metal casing of the outdoor modem (wire: stranded, green, #6 AWG, ROHS; lug: CONN, one-hole #6, ROHS)

4 Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Product_intro.fm / 07.04.2010

The Cisco BWX360 WiMAX Outdoor Modem

Product overview

The Cisco BWX360 WiMAX Outdoor Modem is the WiMAX solution that provides pri- vate and business users with cost-effective access. The Cisco BWX360 WiMAX Outdoor Modem employs non-line-of-sight OFDM technology according to the IEEE 802.16e standard. It provides a standard-based means for offer- ing new forms of voice, video and data services. With the Cisco BWX360 WiMAX Out- door Modem , you can enjoy high-speed , Voice-over-IP telephony (VoIP), video streaming and a range of other services. Template 2006_02_28 Template The Cisco BWX360 WiMAX Outdoor Modem works in the 2.6 and 3.5 GHz frequency range respectively. Due to its architecture, interfaces and simple network integration, the Cisco BWX360 WiMAX Outdoor Modem is designed to deliver high-speed Internet access, including data streaming services. This solution represents a cost-effective, wireless alternative to wired xDSL systems. It provides you with high performance broadband services – with low costs for coverage and high for capacity – and advanced radio resource management. The outdoor modem holds the integrated antennas and is intended for mounting on a wall or a mast. The power is supplied via the Ethernet port (, PoE). The indoor unit is only designed for indoor use and supplies the power to the outdoor modem. It is also the connection point for the terminal (e.g. PC or router).

5 Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Product_intro.fm / 07.04.2010

The Cisco BWX360 WiMAX Outdoor Modem

Connectors and LEDs

Outdoor modem Template 2006_02_28 Template

Outdoor antennas (integrated)

Ethernet socket

6 Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Product_intro.fm / 07.04.2010

The Cisco BWX360 WiMAX Outdoor Modem

Indoor unit

1 2

3

4 Template 2006_02_28 Template 5

6

7

1 Connector for the power supply unit, see "Preparing the power supply" on page 17. 2 CONNECT The LED shows whether or not the indoor unit is properly con- nected to the outdoor modem. ◆ Green: The indoor unit is properly connected to the outdoor modem. 3 FAULT The LED shows whether or not the indoor unit is properly con- nected to the outdoor modem. ◆ Red: The connection between the indoor unit and the out- door modem is faulty. 4ON The LED shows that power is being supplied. ◆ Green: The Cisco BWX360 WiMAX Outdoor Modem is powered correctly. 5IN Ethernet socket for data exchange with a PC or network (RJ45, 10/100 Base T), see "Connecting the PC or laptop" on page 16. 6OUT Ethernet socket for connection with the outdoor modem (RJ45, power supply and data transmission), see "Connecting the indoor unit" on page 15. 7 Clips for wall mounting

You can check the status of the startup procedure on the LEDs, see "Preparing to use the Cisco BWX360 WiMAX Outdoor Modem" on page 17.

7 Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Installation.fm / 07.04.2010

Installing the Cisco BWX360 WiMAX Outdoor Modem Installing the Cisco BWX360 WiMAX Outdoor Modem

For installing the Cisco BWX360 WiMAX Outdoor Modem you have to perform the fol- lowing steps: 1. Choosing locations (see page 9)

Template 2006_02_28 Template 2. Setting up the antenna mast (see page 10). 3. Protecting the mast against lightning (see page 10) 4. Assembling the outdoor modem (see page 12) 5. Connecting the indoor unit (see page 15)

When the installation is completed you have to perform the following steps in order to put your Cisco BWX360 WiMAX Outdoor Modem into operation: 1. Preparing to use the Cisco BWX360 WiMAX Outdoor Modem (see page 17) 2. Launching the user interface (see page 18) 3. Connecting to the WiMAX network and the Internet (see page 19) 4. Precisely aligning the antenna (see page 21) 5. Finishing off the assembly (see page 22)

The Cisco BWX360 WiMAX Outdoor Modem must be assembled and put into service by a qualified electrician. ³ Only commence the outdoor work once you have taken all the neces- sary steps to make the location safe. Be sure to observe the safety precautions.

8 Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Installation.fm / 07.04.2010

Installing the Cisco BWX360 WiMAX Outdoor Modem

Choosing locations

When choosing locations, please note the following: 1. First choose the location for the indoor unit: – When choosing the location, note the specified temperature range of the indoor unit (see "Specifications" on page 23). – The indoor unit is only suitable for indoor use. – The indoor unit can be operated either on a horizontal surface or mounted on a Template 2006_02_28 Template wall. Always make sure the connections cannot become loose once the system has been put into service and check that the LEDs are clearly visible. – Power supply: Power is supplied to the Cisco BWX360 WiMAX Outdoor Modem via the indoor unit. Therefore, the location must be close to a suitable mains connection (cable length of the supplied power supply unit). – Wall duct: To connect to the outdoor modem, the corresponding Ethernet cable must be fed through the wall to the outside of the building. It must be possible to make a suit- able wall duct at or close to the indoor unit. Please note that the maximum permitted cable length is 50 m. – PC or network: Establishing a connection between the indoor unit and a PC or network-switch should ideally be possible from the location via the Ethernet cable. If the PC is moved from its original place, the indoor unit should still be able to be reached simply by using standard cable lengths. 2. Please note the following when setting up the antenna mast/modem: – There should not be any obstructions (walls, trees etc.) in front of the antenna. The best results will be obtained if the outdoor modem is in sight of the WiMAX . If necessary, you can also reflect the radio waves off neighbouring buildings. – The antenna mast must be structurally secure. Check how secure the various attachments are. – The antenna mast must be within reach of the cable. Ideally, the Ethernet cable should be protected outside (from frost, sun, unauthorised and mechanical influ- ences etc.). – The antenna mast should be positioned near a lightning conductor. A suitable lightning conductor must be installed where necessary.

9 Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Installation.fm / 07.04.2010

Installing the Cisco BWX360 WiMAX Outdoor Modem

Setting up the antenna mast

Information on how to install the antenna mast is not included in these installation instructions. Please observe all the safety provisions and other notes contained in the assembly instructions for the antenna mast. In particular, make sure the antenna mast has sufficient load capacity. If you are installing the mast on the roof, make sure the roof is fully sealed again afterwards. If necessary, you can attach the mast brackets to the mast when you install it. Template 2006_02_28 Template Protecting the mast against lightning

Preparation

◆ The outdoor modem is not designed to withstand being struck directly by lightning and must be protected accordingly. The antenna must therefore be installed in areas that are protected against lightning (Lightning Protection Zone 0B). The cor- responding separation distance (IEC 62305) must be complied with. Earthing (grounding) and lightning protection work may only be carried out by elec- tricians specifically qualified for such work. ◆ The appropriate earthing (grounding) clamps must be used to create an equipoten- tial bonding between a cable shield and an equipotential bonding bar that complies with regulations (for sources see "Earthing (gounding) clamps" on page 25).

10 Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Installation.fm / 07.04.2010

Installing the Cisco BWX360 WiMAX Outdoor Modem

Connecting the earthing (grounding) cable to the outdoor modem

Make sure you ground the metal casing of the outdoor modem according to the instruc- tions. 1. Undo or remove the M5 earthing (grounding) screw on the modem casing. 2. Attach the cable lug at the end of the earthing (grounding) cable. Make sure when you do this that the cable lug cannot come loose. You can ensure this, for example, by crimping it twice (once on the flex and again on the insulation) Template 2006_02_28 Template or by applying an appropriately designed shrink tubing which covers the cable lug and the insulation.

The cable lug is not provided. Only use tin-plated cable lugs with eyelet (available from your retailer).

3. Attach the cable lug to the casing with the M5 earthing (grounding) screw. Make sure that the screwed connection cannot come loose. To ensure this, use a toothed contact disc (not supplied), which you fit between the cable lug and the earthing (grounding) screw.

DO NOT screw the earthing (grounding) cable directly to the metal casing of the device, as this could lead to corrosion between the cable and the casing.

11 Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Installation.fm / 07.04.2010

Installing the Cisco BWX360 WiMAX Outdoor Modem

Assembling the outdoor modem

You basically have three options for installing the outdoor modem: ◆ Vertically on a mast (see below), or ◆ Tilted up or down on a mast with an angled bracket (see "Angled installation on a mast" on page 13). Choose the type of installation that allows the best alignment of modem to base station on your building. ◆ Directly attached to a wall Template 2006_02_28 Template Vertical installation on a mast

1. Take the four bolts with the welded-on nuts and screw them into the housing with the shorter end of the bolts, so that the nuts are resting on the housing.

2. Attach the housing to the mast using the clamps and secure the clamps with the nuts.

12 Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Installation.fm / 07.04.2010

Installing the Cisco BWX360 WiMAX Outdoor Modem

Angled installation on a mast

Installing the modem using the supplied bracket allows two possible directions of incli- nation (up or down) and four different tilt angles each, depending on how you attach the bracket to the housing. 1. Fasten the bracket to the housing with the nuts welded onto the bolts: Template 2006_02_28 Template

– To have the modem facing up, fasten the bracket to the bottom edge of the hous- ing; to have the modem facing down, fasten the bracket to the top edge of the housing. – Choose your preferred tilt angle: You get the largest tilt if you fit the bracket with the smaller notch facing inward, and you get the smallest tilt if you fit it with the larger notch facing outward.

2. Attach the housing to the mast using the clamps and secure it with the nuts.

13 Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Installation.fm / 07.04.2010

Installing the Cisco BWX360 WiMAX Outdoor Modem

Preparing to connect to the indoor unit

To connect the indoor unit to the outdoor modem you perform the following steps: 1. Making a wall duct. 2. Provisionally laying the Ethernet cable. 3. Checking connection options in the house. 4. Connecting an Ethernet cable to the outdoor modem. Template 2006_02_28 Template Local building codes must be followed when constructing a wall duct or whatever method of wall penetration is used to pass the ethernet cable into the building.

Making a wall duct 1. Note how close you are to the indoor unit. 2. Check what types of wall ducts are suitable (wall or window duct) and make one.

Provisionally laying the Ethernet cable The cable must satisfy the following conditions: ◆ For connecting the outdoor modem to the indoor unit, only use a round Ethernet cable which is approved for outdoor use. ◆ The outer diameter of the cable must correspond to the clamping area of the con- nector plug. This permitted diameter range is 5 mm to 8.5 mm. ◆ The cable must satisfy the requirements for cables used outdoors at the relevant installation location. The following influencing factors in particular must be taken into account: – Ambient temperature – Rain, water vapour or accumulation of water – Presence of corrosive, contaminative or other chemical substances – Mechanical stresses (e.g. compression stress, tensile loading, torsional load, bending stress, alternating stress etc.) – Animals (e.g. damage caused by rodents or insects) – Plants (e.g. mildew) – Radiation (e.g. UV radiation) ◆ The maximum permitted cable length is 50 m. ◆ To comply with regulations, it may be necessary to ground the cable shield. ◆ To protect the connected IT installation from power surges, you may need to use a surge protection box (see "Surge protection box" on page 24).

Proceede as follows: 1. Feed the non-assembled cable through the wall duct from inside to outside. 2. Lay the cable along the rough path it should take and, if possible, provisionally po- sition fixings.

14 Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Installation.fm / 07.04.2010

Installing the Cisco BWX360 WiMAX Outdoor Modem

Checking connection options in the house Choose one of the following options for connecting the Ethernet cable in the house: 1. Fix the wall connection socket (LSA+ technology) in place and connect the cable from outside to it. For this you will require a corresponding connection socket and possibly a feeder tool for the LSA+ terminal. Feed an Ethernet cable with RJ45 plugs from the wall connection socket to the indoor unit (standard CAT5e, available from your retailer in various lengths). 2. Connect the cable from outside directly to the indoor unit. For indoor use, you need Template 2006_02_28 Template an RJ45 plug, see "Sources" on page 24. Feed an Ethernet cable with an RJ45 plug from the indoor unit to a PC or router (standard CAT5e, available from your retailer in various lengths).

Connecting an Ethernet cable to the outdoor modem 1. Slip the support sleeve over the unassembled cable to be screwed in later. 2. Attach a Phoenix connector to the end of the Ethernet cable that is outside. Please read the instructions that come with the plug. 3. Insert the RJ45 plug of the assembled cable into the Ethernet socket of the outdoor modem. 4. Slide the sleeve over the connected RJ45 plug and screw this into the Ethernet socket. Make sure the connection is water-tight. 5. Use cable clamps to attach the cable to the mast. Please note that the cable must be long enough to turn the antenna at a later stage. 6. Lay and attach the cable from the antenna mast along a path on which its function- ality is not affected by external influences.

Connecting the indoor unit

Wall mounting (optional)

The indoor unit is fitted with two clips for wall mounting. Wall mounting is not absolutely necessary, but is recommended to make the cable connections mechanically secure. ◆ Use screw fittings, anchor fittings and cable clamps to mount the indoor unit on a wall. ◆ Make sure the LEDs are easily visible.

15 Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Installation.fm / 07.04.2010

Installing the Cisco BWX360 WiMAX Outdoor Modem

Establishing the cable connections

The indoor unit should not be considered as an Ethernet terminal. The full length of the Ethernet cable from the outdoor modem to the Ethernet ter- minal (e.g. a router or a PC) must not exceed 100 m. The maximum per- mitted cable length between indoor unit and outdoor modem is 50 m. If you utilise this completely the cable length between Ethernet terminal and indoor unit must also not exceed 50 m. Template 2006_02_28 Template Connecting the outdoor modem 1. Shorten the cable to the length required for connecting it to the indoor unit: – If there is any surplus cable, pull this inside through the wall duct. – Lay the inside section of the cable up to the location of the indoor unit or the wall connection socket and attach the cable professionally. – Fit an Ethernet plug to the cable end. First shorten the cable to a length that allows the indoor unit or the wall connec- tion socket to be easily reached. 2. Connect the RJ45 plug of the Ethernet cable from the outdoor modem to the OUT connector of the indoor unit. Or 1. Connect the RJ45 plug of the Ethernet cable of the outdoor modem to the wall con- nection socket. 2. Connect the wall connection socket and the indoor unit using an Ethernet cable (CAT5e).

Connecting the PC or laptop

When the Cisco BWX360 WiMAX Outdoor Modem has been assembled and is put into service, it is connected to the PC or the customer's network via the IN connector of the indoor unit. When you first put the system into service, it is recommended that you first connect a laptop that has the appropriate settings for this purpose. For information on what settings to make on the laptop, please read the sup- plied user guide.

1. Connect the supplied, pre-assembled Ethernet cable to the IN connector on the in- door unit. 2. Then connect the Ethernet cable to the Ethernet socket on the PC or laptop that you are using for putting the system into service for the first time. The PC or laptop with the special settings can be on and ready for use, but this is not obligatory.

16 Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Installation.fm / 07.04.2010

Installing the Cisco BWX360 WiMAX Outdoor Modem

Preparing the power supply 1. Check that all of the assembly steps and connections up to this point have been made correctly and in full. 2. Connect the supplied power supply unit to the POWER connector of the indoor unit.

Only use the Cisco BWX360 WiMAX Outdoor Modem with the supplied power supply unit. Part number: C39280-Z4-C584

Template 2006_02_28 Template Input: 100-240 V, 0.95 A AC Output: 56 V, 0.55 A DC

3. Begin putting the system into service. As soon as you have connected the indoor unit to the mains power supply, the sys- tem is started up. Preparing to use the Cisco BWX360 WiMAX Outdoor Modem

1. Start up the connected PC or laptop and make any necessary settings. You will find the preconditions for the PC in the user guide for the Cisco BWX360 WiMAX Out- door Modem. 2. If you are sure you have connected everything up correctly, connect the indoor unit to a power socket that is ready for use via the power supply unit. The system starts up and performs a self-test.

The connection technology between the outdoor modem and the indoor unit complies with the "PoE" standard. This means the DC power is supplied via the Ethernet cable (Pins 4/5 = Power +, Pins 7/8 = Power - ) The DC voltage supplied to the indoor unit is 56 V with a maximum deviation of 4%. As part of the standard, a self-test is performed to check the voltage between the connected devices is correct. The indoor unit only releases its supply voltage once the outdoor modem and the indoor unit have accepted the correct voltage. ³ If the activation is not successful, check whether the connections have been correctly assembled.

After the self-test, the Cisco BWX360 WiMAX Outdoor Modem continually attempts to register with a base station. Registration with the base station may be successful immediately. If not, registration will take place when the Cisco BWX360 WiMAX Outdoor Modem is being configured (see "Connecting to the WiMAX network and the Internet" on page 19)

17 Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Installation.fm / 07.04.2010

Installing the Cisco BWX360 WiMAX Outdoor Modem

3. During the startup procedure, check the LED display on the indoor unit (see "Indoor unit" on page 7). The following signify a successful system start: –The ON power supply LED lights up green, and the Cisco BWX360 WiMAX Out- door Modem starts a self-test. –The FAULT LED (red) and the CONNECT LED (green) light up for approximately 1 second and then go out. – If the connection to the outdoor modem is then found to be free from errors, the CONNECT LED is continuously lit up green.

Template 2006_02_28 Template If an error occurs, the FAULT and CONNECT LEDs start to flash alternately at regular intervals. Launching the user interface

1. Open your Web browser. 2. Enter the IP address of the Cisco BWX360 WiMAX Outdoor Modem in the browser's address field: http://192.168.2.1 3. Press Enter (Return).

Login If a system password has been set up on the Cisco BWX360 WiMAX Outdoor Modem, the login screen will now open. 1. Enter the system password supplied by your provider in the text box and clickOk. The start page of the user interface opens, in which you can change the language if necessary. If no system password has been set up on your Cisco BWX360 WiMAX Outdoor Modem, a security warning will appear first. You should then assign a system pass- word as soon as possible. 2. Confirm the security warning with Ok. The user interface start page opens.

If the login screen does not open: ³ Check the connections and the PC configuration. For details, refer to the user guide for the Cisco BWX360 WiMAX Outdoor Modem. ³ If you use a firewall it must allow connection to the Cisco BWX360 WiMAX Outdoor Modem. For details, refer to the user guide for your firewall. If necessary, deactivate the firewall while you configure the Cisco BWX360 WiMAX Outdoor Modem.

18 Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Installation.fm / 07.04.2010

Installing the Cisco BWX360 WiMAX Outdoor Modem

Setting the language The user interface can be displayed in several languages, such as German, English, French and Spanish. If your provider has not preconfigured default settings, the lan- guage when you first call up the user interface is English. ³ If you wish to set your language, click on the Language button and select your lan- guage. Connecting to the WiMAX network and the Internet Template 2006_02_28 Template If there is a connection between the PC or laptop and the outdoor modem, the Internet connection must be configured and a radio connection must be established with the base station. You do this in the Basic Setup Wizard. 1. Click the Basic Setup Wizard tab. 2. Click Next. 3. If you need help for a particular page, click the question mark button.

Entering the access data for the WiMAX network

On this page you enter the data for authentication of your device on the WiMAX base station. You will need the access data supplied by your WiMAX operator for this. ³ Enter the access data and click Next.

Setting up Internet access

To allow users in your local network access to the Internet, set up the Internet connec- tion of your device using the information supplied by your Internet provider. ³ Enter the access data and click Next.

Adjusting the antenna

1. Turn your Cisco BWX360 WiMAX Outdoor Modem towards the base station. 2. Click Next.

Establishing a radio connection with a WiMAX base station

The Basic Setup Wizard now scans the frequencies. This establishes an initial radio connection with a WiMAX base station. The frequency scan starts automatically. A progress bar indicates how far the fre- quency scan has already progressed. In addition you will see in the Remaining time area roughly how much time is still needed for the complete scan. Depending on how the Cisco BWX360 WiMAX Outdoor Modem was preconfigured by the provider, the first scan to establish a radio connection can take several minutes.

During the scan, the antenna must not be moved; this is the only way to guarantee a complete scan with the current antenna alignment.

19 Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Installation.fm / 07.04.2010

Installing the Cisco BWX360 WiMAX Outdoor Modem

As soon as a radio connection has been established with a WiMAX base station, the scan will end. The progress bar is fully filled in and the display in the Remaining time area jumps to 0 seconds. ³ If the scan was successful, continue reading from "Precisely aligning the antenna" on page 21.

If the scan was not successful: The integrated antenna is directional. This means it must be pointing roughly in the

Template 2006_02_28 Template direction of a WiMAX base station in order to establish a radio connection. The access data must also have been entered correctly. 1. First check your access data by going back to the WiMAX configuration page. 2. Turn the modem approx. 20° and restart the scan. You may need to turn the anten- na several times.

The best results will be obtained if the outdoor modem is in sight of the WiMAX base station.

If a line of sight is not possible, you can reflect the radio waves off neighbouring buildings. For this, direct the antenna at the building it is to reflect off and not at the base station.

20 Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Installation.fm / 07.04.2010

Installing the Cisco BWX360 WiMAX Outdoor Modem

Precisely aligning the antenna

Once you have established a wireless connection to a WiMAX base station, align the antenna precisely using the Basic Setup Wizard. For this it can be useful if an assistant follows the alignment on the PC. Please ask the customer for support. If this is not pos- sible, read "Aligning the antenna with the acoustic response" on page 21. 1. Turn the antenna step by step and have the assistant watch the connection status on the PC.

Template 2006_02_28 Template 2. When a connection to a WiMAX base station has been established, the assistant clicks on Next to make fine adjustments to the antenna. The quality of the radio connection can be seen in the Signal quality area. The signal quality bar graph indicates the quality of the connection. You will also see the signal quality shown as a percentage as well as an assessment of the connection quality:

Excellent The wireless connection is at the highest level. Very good The wireless connection is very good. You can attempt to improve the connection still further by turning the antenna slightly; however, this is not necessary. Good The wireless connection is already good. Turn the antenna slightly to further improve the connection. Sufficient The wireless connection has been established. Turn the antenna a little at a time to improve the connection. No connection If you have turned or moved the antenna too far the wireless con- nection to the WiMAX base station will break up. Return the antenna to the position it was in when the connection was suc- cessfully established. The wireless connection to the WiMAX base station will be restored immediately.

³ Turn the antenna a little at a time and have the assistant observe the signal strength display. Use this to move the antenna to the position with the best signal strength.

Aligning the antenna with the acoustic response If neither you nor the assistant are able to check the signal strength on screen while the antenna is being aligned, you can monitor it via a radio system. To do this you will need, for example, two cordless phones, mobile phones or radio devices: 1. Activate Audible feedback on the configuration PC. 2. Establish an internal connection between the two handsets and switch on the loudspeaker on both devices. 3. Leave one handset next to the configuration PC and carry the other with you (belt clip). You will now be informed of the signal strength by means of beeps. The closer together the sequence of beeps, the better the connection quality.

21 Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Installation.fm / 07.04.2010

Installing the Cisco BWX360 WiMAX Outdoor Modem

When the antenna is precisely aligned: ³ Click on End. Finishing off the assembly

1. Tighten the screw fixings. Please be aware of local laws. Installation should be performed by a qualified per- son.

Template 2006_02_28 Template 2. Attach the Ethernet cable with cable clamps and cable ties. Make sure the cable is protected against the effects of pressure. 3. Brief the user on what to do if they have any problems or if they need to upgrade the system etc.

22 Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Appendix.fm / 07.04.2010

Appendix Appendix

Troubleshooting

For troubleshooting notes, please refer to the user guide supplied. Specifications Template 2006_02_28 Template Model Cisco BWX360 WiMAX Outdoor Modem Dimensions Outdoor modem: approx. 228.5 x 208 x 101 mm indoor unit: approx. 140 x 65 x 36 mm Operating temperature Outdoor modem: –40 °C to +60 °C indoor unit: 0 °C to +40 °C Storage temperature –25 °C to +55 °C Network interface 1 Ethernet 10/100BaseT (RJ45, LAN) Frequency 2.3–2.4 / 2.5–2.7 / 3.4–3.6 GHz Output power up to 26 dBm at QAM-16 Power consumption 3-6 W on DC input depending on operational state optional 3.5 / 5.0 / 7.0 / 8.75 or 10.0 MHz Type of transmission TDD Modulation technique SOFDMA 512/1024 Subcarrier modulation QPSK, 16/64 QAM in up- and download Antenna type 2 internal antennae (2xRX, 1xTX) for MIMO Matrix A & B; Type DN1 (EN 302 326-3 V1.2.2) Antenna gain 7 / 11 dBi (2.6 / 3.5 GHz) Power supply unit Input: 100–240 V AC, Power over Ethernet (PoE)

23 Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Appendix.fm / 07.04.2010

Appendix

Sources

Ethernet cable

◆ Phoenix Order address: http://www.phoenixcontact.com Phoenix Contact GmbH & Co. KG Template 2006_02_28 Template Flachsmarktstr. 8 32825 Blomberg Germany Phone: +49(0)5235-3 00 Fax: +49(0)5235-34 12 00 [email protected] ◆ Yamaichi Order address: http://www.yamaichi.de Yamaichi Electronics Deutschland GmbH Karl-Schmid-Straße 9 81829 München Germany Phone: +49(0)89 / 45109-0 (Fax: -110)

RJ45 Ethernet plug

Ethernet plug for outdoor use ◆ http://www.phoenixcontact.com VS-08-RJ45-5-Q/IP67-SHO, Item no.: 1657973, Colour: black

Ethernet plug for indoor use ◆ http://www.phoenixcontact.com VS-08-RJ45-5-Q/IP20, Item no.: 1656725

Surge protection box

◆ http://www.dehn.de DPA M CAT 6 RJ45S 48 ◆ http://www.citel.de Network protection – MJ8-505 ◆ http://www.hyperlinktech.com/web/cat5_data_line_surge_protectors.php

24 Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Appendix.fm / 07.04.2010

Appendix

Earthing (gounding) clamps

◆ Ground cable for earthing (grounding) the metal casing of the outdoor modem (wire: stranded, green, #6 AWG, ROHS; lug: CONN, one-hole #6, ROHS)

The cable shield can be connected to the equipotential bonding by means of a copper band. You must ensure the cable is sealed against moisture, e.g. with standard bitumen tape. Template 2006_02_28 Template Notes on putting into service

This device will only operate on Sprint or 's U.S. WiMAX network. It is not intended for use on any other network. Please observe the legal provisions and local restrictions when putting the device into service. Please ask your service provider for further information.

25 Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / Appendix.fm / 07.04.2010

Appendix

Federal Communications Commission (FCC) Statements

This device complies with Part 15 of the FCC Rules. Operation is subject to the follow- ing two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Template 2006_02_28 Template Radio Frequency Interference Statement

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to pro- vide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the fol- lowing measures: 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that to which the re- ceiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncon- trolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The installation of the base unit should allow at least 8 inches between the base and persons to be in compliance with FCC RF exposure guidelines.

Modifications

You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

26 Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / SE680WiMAXSIX.fm / 07.04.2010

Index Index

A Installation...... 8 Aligning the antenna ...... 19, 21 Installing Antenna mast ...... 10 aligning the antenna ...... 21 Appendix ...... 23 antenna mast ...... 10 CE declaration...... 26 assembling ...... 12

Schablone 2006_02_28 sources...... 24 choosing locations ...... 9 technical data ...... 23 connecting to indoor unit...... 14 troubleshooting ...... 23 earthing cable, grounding cable . . . 11 Assembling lightning protection ...... 10 outdoor modem ...... 12 Internet access Assembling outdoor modem ...... 12 setting up ...... 19

B L Basic settings LEDs during startup...... 18 setting up Internet access ...... 19 Lightning protection ...... 10 Basic Setup Wizard ...... 19 earthing cable, grounding cable . . . 11 starting ...... 19 BWX360 WiMAX Outdoor Modem M putting into service ...... 17 Mounting...... 10 modem with antenna ...... 15 C Choosing locations ...... 9 N Notes on assembly instructions ...... 3 E Earthing cable ...... 11 O Ethernet cable Outdoor modem ...... 6 connecting to outdoor modem . . . . 15 assembling ...... 12 provisionally laying ...... 14 P F Power over Ethernet, PoE ...... 5 FCC Statements ...... 26 S G Safety ...... 2 Grounding cable ...... 11 notes on assembly instructions . . . . .3 Grounding see Earthing Safety precautions...... 2 Setting the language ...... 19 I Setting up Internet access ...... 19 Indoor unit ...... 7 Sources ...... 24 cable connections ...... 16 Specifications ...... 23 connecting ...... 15 connecting PC or laptop...... 16 T power supply...... 17 Troubleshooting...... 23 wall bracket...... 15

27 Cisco BWX360 WiMAX Outdoor Modem / engbt / 253306943 / SE680WiMAXSIX.fm / 07.04.2010

Index

U W User interface, setting the language . 19 Web browser launching user interface ...... 18 WiMAX network access data ...... 19 Schablone 2006_02_28

28