ARISAKA Harris Bipod Mount Installation

Total Page：16

File Type：pdf, Size：1020Kb

ARISAKA LOW PROFILE HARRIS BIPOD MOUNT INSTALLATION Installation of the Arisaka Low Profile Bipod Mount involves disassembling your Harris S-series bipod to remove the stock sling swivel mount. 1. Use a 1/4" socket wrench to loosen and remove the nut inside the thumbscrew on the rear of the bipod. 2. Unthread and remove the thumbscrew from the rear of the bipod. 3. Gently slide the entire sling swivel mount off the front of the bipod. The center screw, cross pin, and thick slotted brass washer will also come off. A second thin washer should be left on the main shaft of the bipod. Be careful not to lose any pieces! 4. Next is reassembly. Place the Arisaka Low Profile Bipod Mount onto the center shaft, followed by the thick slotted brass washer with the tapered side facing forward (Or up as shown in the below picture). Orientation of the mount does not matter except for side preference of the clamping screw. 5. Insert the cross pin into the long main screw, and carefully insert it into the center shaft of the bipod. The cross pin should engage the thick slotted brass washer and center shaft as shown below. 6. Hold the center screw, cross pin, and brass washer in place while threading the thumbscrew onto the center screw protruding from the rear of the bipod. The thumbscrew should be snugged down until finger tight. The nut can then be threaded on using the 1/4" socket wrench. Do not tighten the nut all the way; you want to leave enough room so the thumbscrew can be slightly loosened to allow the bipod to cant. 7. If you use a Locking Lever System such as CORETAC SOLUTIONS CoreLock™ (which is highly recommended) then it can be installed instead of the thumbscrew and nut. 8. Install the bipod onto a rifle by removing the clamping cross screw with a 5/32" Allen wrench, sliding it onto a Picatinny rail, and then replacing the cross screw. The screw should be tightened until the mount slightly flexes and securely grabs the rail, approximately 55-65 inch lbs. .

Copy Link

Recommended publications

Instruction for Vector Optics Tactical Bipod Mounts ATTENTION: Make Sure Firearm Is Unloaded Universal Picatinny Style
Instruction for Vector Optics Tactical Bipod Mounts ATTENTION: Make sure firearm is unloaded Universal Picatinny Style Fit 21mm weaver and picatinny rail Press down the lockable button to open or folder the bipod Turn and release the leg sleeve, the spring loaded leg will be extended, then fasten the leg sleeve again To retract the leg, loosen the leg sleeve, push back the leg to the end, retighten the leg sleeve again Solid rubber feet avoid slipping With barrel mount adapter Stud Connection Style Stud connection mount for sling attachment Press the button to release the spring loaded leg If need to retract the extendable leg, just press the button again and push the leg back Solid rubber feet avoid slipping With weaver picatinny mount adapter. To use the adapter, remove the bipod tiny rubber sleeve, clamp into the adapter stud hole. Fasten the bottom nut. Swivel Stud Connection Style Swivel stud connection mount for sling swivel attachment Press the button to release the spring loaded leg 15 inch bipod, press first button and pull the extendable legs, press last button to release the spring loaded leg If need to retract the extendable leg, just press the button again and push the leg back Solid rubber feet avoid slipping Weaver picatinny mount adapter. To use the adapter, remove the bipod tiny rubber sleeve, clamp into the adapter stud hole. Fasten the bottom nut. Swing-able design for leveling on uneven ground. Select proper angle and fasten thumb nut to lock the position www.scvector.biz www.scvector.com .
[Show full text]
Manson Precision Receiver Accurizing System
Manson Precision Receiver Accurizing System Rhomboidal and pavid Slim reinterred her sundries feign or municipalizes estimably. Bewhiskered and dorsiventral Shurlock often disorientates some suspiration jeopardously or gumshoe therapeutically. Toothsome Ned sometimes climb-downs any hypogyny objectivize thriftily. Austenite molecular structure in receiver accurizing your order to impact forging die was attached to It has a receiver accurizing and precision machined hand when needed. National Match Rifle, Serial No. Ups For Remington Centerfire Rifles MAGAZINE CLIP is best carrying cases for extra ammo; they spoke right knowledge the gun. Available in precision manufacturing, deeply serrated face! Winchester receiver accurizing system and precision receiver, butt plate screw only received and the systems, the barrel bore. Sold had designed by the receiver accurizing kit! If they are precision. Even directional change the receiver accurizing system for precise, fulton armory operating rod rail hand and flexibility. The replacement magazine followers should have three neat and evenly spaced spot welds attaching the stop to the follower. End to match category will enlarge due to. The magazines were rotated for even use and the rate of fire was measured during one of the twenty round bursts. It is precision receiver accurizing system was unable to do so you wont need to work was a manson. He fled to the jungle the same day. SPECS: Aluminum, anodized, red. The reamer has a FLOATING pilot that measures approx. Bush and receiver. SPECS: Stainless steel, belt finish. Tactical Forums discussion board www. Low maintenance, Parkerized finish resists corrosion and matches the rest of your rifle. This corn is therefore excellent turnover and fluctuate barely ever used.
[Show full text]
Art of Precision
2017 CATALOGUE ART OF PRECISION «Promtechnologia» (Industrial Technology) company directs careful attention to its products’ quality which allows it to gain some impressive results: Orsis rifles’ accuracy exceeds their most common counterparts’ results greatly. This reality is confirmed by the multiple winning scores of shooters participating in high-accuracy shooting international competitions with their Orsis rifles in hands. There is a parameter in ballistics called “minute of angle” (or MOA) which estimates accuracy of shooting and it is defined, as a rule, by a group of 3-5 shots. Rifles having MOA ratio less than 1 are called sniper rifles. «Promtechnologia» company guarantees that all Orsis rifles demonstrate accuracy not over 0.5 MOA and a number of models demonstrate even better performance. www.orsis.com 3 President’s Message 4 Orsis Special 6 Orsis SE T-5000 M 8 Orsis M-15 Carbine 12 Orsis AR-10 National Match 16 Orsis Hunting 20 Orsis 120/140 22 Orsis SE Hunter M 26 Orsis SE Alpine M 30 Marocchi Si12 / Walnut 34 T-5000 / 8-11 120/140 / 22-25 Varmint / 48-51 Marocchi Si12 / Plastic 36 Marocchi First-E 40 Marocchi First-E Deluxe 42 Orsis Sport 46 Orsis Varmint M 48 Orsis F-Class 52 Glock Pistols 54 M-15 / 12-15 Hunter / 26-29 F-Class / 52-53 Production 56 High-Technology Equipment 58 High-Precision Technologies 59 Exceptional Materials 60 Innovative Development 61 International Cooperation 61 AR-10 / 16-19 Alpine / 30-33 Glock / 54-55 Services 62 Rifle Barrels Replacement 63 Cerakote Coating Application 63 Technical Maintenance 64 Decoration & Engraving 65 Orsis Сustom 65 Dealer Network 66 Marocchi / 34-45 Contacts 66 HIGH-PRECISION FIREARMS SYSTEMS ORSIS 4 ORSIS ART OF PRECISION President’s Message 5 Dear friends! The first catalogue of «Promtechnologia» (Industrial Technology) We support our shooters’ aspiration to be the best hunters and company is now introduced for your kind attention and, as you will sportsmen.
[Show full text]
Summary Description Semi-Automatic Sporting Rifle SIG-AMT Cal
- Summary Description Semi-Automatic Sporting Rifle SIG-AMT cal. 7.62x51 mm (.308 Win.) Swiss Industrial Company CH- 8212 Neuhausen Rhine Falls/Switzerland Phone 053/81555 Telex 76156 sig ch - 3 - Contents l. Weapon theory Page l.l. Designation and purpose 5 1.2. Main components and accessories 6- 7 1.3. Dismantling and assembly 9 1.4. Cleaning and maintenance ll 1.5. Functional checks 12 2. Manipulation 2.1. Loading, reloading, unloading 13-14 2.2. Positions of firing, using normal ammunition 14 2.3. Sight adjustments 16 3. Technical data 17-18 - 4 - - 5 - l. Weapon theory 1.1. Designation and purpose The semi-automatic sporting rifle SIG-AMT is a delayed blow-back weapon with stationary barrel and semi-rigid breech. The cartridges are fed from magazines of 5, 10 or 20 rounds. A considerably reduced recoil and the bipod which lends the rifle a firm support, improves accuracy of aim in all types of fire. Next to the normal trigger, in latched neutral position, is a winter trigger. This can be un latched and shifted into engagement to allow firing in mittens. In the head of the breech casing is a loading indicator, affording a visual check as to whe ther the weapon is loaded or unloaded. - 6 - - 7 - 1.2. Main components Accessories The principal parts of the weapon are: - Magazines for 5, 10 or 20 rounds - Barrel, bolted firmly to the breech casing. - Sling Pull-through with string and wire brush Breech casing with 2 lock heads, carrying - Loading indicator holder handle, loading indicator, bolt, rear sight and cartridge ejector opening.
[Show full text]
CASV Handguard for the FAL Rifle Note: the CASV-FAL System Will Not Fit on Rifles Using the G1 Or Similarly Profiled Barrels
CASV Handguard for the FAL Rifle Note: The CASV-FAL System will not fit on rifles using the G1 or similarly profiled barrels Improper installation can result in damage. Do not attempt installation if you are not familiar with the firearm, tools and techniques mentioned. You are responsible for any damage or READ injury resulting from the improper use THIS! or installation of this product. Ensure the rifle is CLEAR and SAFE! Before installation, read Instructions, Warnings and Notes. NOTE: Make sure that the firearm is unloaded and safe before proceeding – if you are unsure of how, or uncomfortable with the proper clearing and safe handling of the firearm, do not proceed! We recommend that the installation of this part be done only by a qualified gunsmith or agency armorer. 1. Before proceeding, please inspect the handguard assembly and hardware to ensure that you are familiar with all of the parts. 1 - Upper handguard Assembly 2 - Lower handguard Assembly 3 - Forward mounting screw retaining clip 4 - Forward mounting screw 5 - Rear mounting cross screw 6 - Rear mounting clamping nut 7 - Upper Handguard retaining screws (6 for FAS, 8 for FAL) 8 - Picatinny Accessory Rails & Screws 2. Install the lower handguard section by sliding it over the front sight gas block, and rearward over the handguard retainer. After the lower section is in place, install the forward mounting screw from the right side of the handguard, ensuring that it goes through the front sight gas block. Note: only snug the screw enough to hold the lower handguard section in place. 3.
[Show full text]
PM Crew Served Weapons Overview Small Arms Symposium & Exhibition
TheThe Soldier:Soldier: America’sAmerica’s MostMost DeployedDeployed CombatCombat SystemSystem PM Crew Served Weapons Overview for the Small Arms Symposium & Exhibition National Defense Industrial Association 16-19 May 2006 BG James R. Moran COL Carl A. Lipsit Mr. Peter Errante Program Executive Officer Soldier PM Soldier Weapons Deputy PM Crew Served Weapons Crew Served Weapons 2 PM Soldier Weapons Programs List DEVELOPMENT WEAPONS PROCUREMENT Objective Individual Combat Weapon (OICW) 37. M101, CROWS, Remote Mount 1. OICW Increment I 38. M151E1 & M151E2 Protector Remote Wpn System (RWS) 2. OICW Increment II - XM25 Air Burst Weapon 39. MK19 Advanced Crew Served Weapons (ACSW) 40. Mod Kit 3. Advanced Crew Served Weapon (ACSW) Programs 41. Lightweight Adjustable Sight Bracket 42. Tactical Engagement Simulator (TES) SOLDIER ENHANCEMENT PROGRAMS 43. M107 Semi Automatic Long Range Sniper Rifle 4. XM26 - 12 Gauge Modular Accessory Shotgun System 44. M240B, 7.62mm Medium MG (MASS) 45. M240B Collapsible Buttstock 5. Joint Combat Pistol 46. M192, Light Weight Ground Mount For MG 6. Family of Small Arms Suppressors 47. Improved Bipod 7. M68 Close Combat Optics (Dual Source Qualification) 48. Improved Flash Suppressor 8. XM1068, 12 Gauge Non-Lethal Extended Range Round 49. Combat Ammunition Pack 9. XM1022, Sniper Ammunition for M107 50. M240B Short Barrel 10. XM110 - 7.62 Semi-Automatic Sniper System (SASS) 51. M240B Improved Buttstock 11. Close Quarters Battle Kit 52. Sling Assembly for the M240B 12. XM1041/XM1042/XM1071 - Close Combat Mission 53. Short Barrel Capability Kit 54. M249, 5.56mm Squad Automatic Weapon 13. Advanced Sniper Accessory Kit (ASAK) 55. M192, Lightweight Ground Mount For MG 14.
[Show full text]
Orders: 800-741-0015
HOWARD LEIGHT 3M PELTOR TRI-FLANGE ACCESSORIES SHOOTING SHOOTING ACCESSORIES INDEX IMPACT BOLT MUFFS REUSABLE EARPLUGS Ammo Boxes & Range Gear ........ 361 Safety & Training Aids ........ 370-371 Impressivley FAST Electronic Sound Comfortable, Snug Fit To Seal Magazine Loaders ............ 367-368 Shooting Aids ............... 368-370 Suppression + Other Feature Upgrades Out The Noise - Full 26 NRR Howard Leight’s premium electronic Impact Soft, triple flanged plugs adapt Protective Gear ................ 359-360 Timers & Chronographs ....... 366-367 Bolt muffs turn the amplifier on and off about 250 to the shape of the ear canal for a times faster than typical electronic muffs. That custom fit that protects your hear- Rests & Bipods ............... 362-366 means, as soon as a gunshot-noise spike over 82 dB is detected, the ing from loud noises. Made of pliable, non-irritating polymer, these circuits shut down the audio in ½ millisecond. When the noise has earplugs have a plastic stem that lets you quickly and easily insert passed, the amplifier turns back on just as quickly. This speed keeps the plugs without touching the pre-molded tips. They're washable, you connected to your shooting environment by eliminating sound- ® Colors too, so you'll get plenty of range sessions out of the. Poly cord keeps SIMS VIBRATION LABORATORY LIMBSAVER clipping - the inadvertent blocking of ambient sounds just after a them together when in use or storage, and the bold, hi-viz fluores- HOWARD LEIGHT IMPACT SPORT gunshot. The result is you don’t experience that odd sense of “discon- cent green color makes them even harder to lose! ab PROTECTIVE SHOOTING PAD nection” common to electronic muffs, helping you hear range com- SPECS: Soft polymer, florescent green.
[Show full text]
Experimentation in Sling Weaponry: Effectiveness of and Archaeological Implications for a World-Wide Primitive Technology
University of Nebraska - Lincoln DigitalCommons@University of Nebraska - Lincoln Anthropology Department Theses and Dissertations Anthropology, Department of 4-2013 Experimentation in Sling Weaponry: Effectiveness of and Archaeological Implications for a World-Wide Primitive Technology Eric T. Skov University of Nebraska-Lincoln, [email protected] Follow this and additional works at: https://digitalcommons.unl.edu/anthrotheses Part of the Anthropology Commons Skov, Eric T., "Experimentation in Sling Weaponry: Effectiveness of and Archaeological Implications for a World-Wide Primitive Technology" (2013). Anthropology Department Theses and Dissertations. 30. https://digitalcommons.unl.edu/anthrotheses/30 This Article is brought to you for free and open access by the Anthropology, Department of at DigitalCommons@University of Nebraska - Lincoln. It has been accepted for inclusion in Anthropology Department Theses and Dissertations by an authorized administrator of DigitalCommons@University of Nebraska - Lincoln. Experimentation in Sling Weaponry: Effectiveness of and Archaeological Implications for a World-Wide Primitive Technology by Eric Skov A THESIS Presented to the Faculty of The Graduate College at the University of Nebraska In Partial Fulfillment of Requirements For the Degree of Master of Arts Major: Anthropology Under the Supervision of Professor LuAnn Wandsnider Lincoln, Nebraska May, 2013 EXPERIMENTATION IN SLING WEAPONRY: EFFECTIVENESS OF AND ARCHAEOLOGICAL IMPLICATIONS FOR A WORLD- WIDE PRIMITIVE TECHNOLOGY Eric Thomas Skov, M.A. University of Nebraska, 2013 Adviser: LuAnn Wandsnider The sling is a simple, cheap and effective weapon that was widely distributed among prehistoric and historic populations. Well-known archaeological and textual evidence attests to its widespread military usage in Europe, South America and Central America. However, ethnographic and archaeological evidence also suggest that the sling was widely distributed among Native American populations.
[Show full text]
USER MANUAL AR15 STYLE RIFLES Barnes Precision Machine A2-Style Muzzle Device
INNOVATIVE REFINEMENTS TO THE TACTICAL CARBINE www.USAmade-AR15parts.com USER MANUAL AR15 STYLE RIFLES Barnes Precision Machine A2-Style muzzle device. Reduces muzzle blast and felt recoil, complete with breaching tip. MADE IN THE USA All Barnes Precision Machine rifles come standard with a stainless steel match grade barrel. Available in your choice of .223 Wylde or 5.56 NATO chambers and 11.5 to 18 inch lengths. Picatinny Spec Free-Float Rail System. Available in 7, 9, 12.5, and 14.5 inch lengths, featuring our patent pending enhanced barrel nut to achieve unprecedented rigidity for the length of the rail. Each rail system features four steel reinforced interchangeable sling swivel inserts. 7075 Forged Mil-spec CNC machined-hard anodized lower receiver with accurizing screw and detent set screw. Barnes Precision Machine © Copyright 2013 Patent Pending, All Rights Reserved Congratulations, you have purchased one of the finest rifles in the industry. Mil-spec machine tolerances. Manufactured on state of the art CNC machinery. Top quality materials-coating. All performed to ISO9001 standard. USA made craftsmanship and pride by skilled machinists in our North Carolina Facility. Innovative refinements to the tactical carbine OPERATING INSTRUCTIONS For safe operation instructions including Proper /Safe usage and /or maintenance, cleaning, repair, BPM Inc. recommends completion of a class by certified instructor (NRA/ NSSF, etc.) for training /operational understanding-proper, safe use of weapon system for tactical/personal defense/target/hunting as well as all other applications requiring basic understanding of said product(s) for SAFE /RELIABLE use/application of a LETHAL WEAPON. WARRANTY Due to the many different requirements imposed by federal and state laws on consumer warranties, no express warranty, either “full” or “limited” is offered with this product.
[Show full text]
(12) United States Patent (10) Patent No.: US 7,121,034 B2 Keng (45) Date of Patent: Oct
USOO7121034B2 (12) United States Patent (10) Patent No.: US 7,121,034 B2 Keng (45) Date of Patent: Oct. 17, 2006 (54) BPOD MOUNT AND GRIPASSEMBLY 6,487,807 B1 * 12/2002 Kopman et al. ............... 42.94 2005/0241206 A1* 11/2005 Teetzel et al. ................. 42.72 (76) Inventor: Da Keng, 875 Wharton Dr. S.W., Atlanta, GA (US) 30336 FOREIGN PATENT DOCUMENTS (*) Notice: Subject to any disclaimer, the term of this DE 103.108O2 A1 * 9, 2004 patent is extended or adjusted under 35 U.S.C. 154(b) by 0 days. * cited by examiner Primary Examiner J. Woodrow Eldred (21) Appl. No.: 11/056,134 (74) Attorney, Agent, or Firm Jones Tullar & Cooper, PC (22) Filed: Feb. 14, 2005 (57) ABSTRACT (65) Prior Publication Data A grip and bipod mounting device for mounting a bipod US 2005/O188588 A1 Sep. 1, 2005 Supporting grip assembly to a "picatinny’ mounting rail structure as are often affixed below the forearm stock of a Related U.S. Application Data firearm such as a military rifle (e.g., as per standard MIL STD-1913). In particular, the present invention is directed to (60) Provisional application No. 60/543,571, filed on Feb. mounting a Parker-Hale style of firearm bipod on a bipod 12, 2004. Supporting grip assembly including a contoured mounting (51) Int. C. block segment inletted to cover and attach to a picatinny rail affixed beneath the forearm stock of the firearm. A grip or F4 IC 23/00 (2006.01) handle depends transversely from the mounting block seg (52) U.S.
[Show full text]
Universal Featherweight Bipod
UNIVERSAL FEATHERWEIGHT BIPOD FitS: Any Firearm with a Sling Swivel Stud and AR-15 Types INSTALLATION INSTRUCTIONS PART# BIP0300 MAKE SURE YOUR FIREARM IS UNLOADED BEFORE STARTING! UNIVERSAL BIPOD ASSEMBLY: INSPECT EXISTING SLING SWIVEL STUD FOR TIGHTNESS! NON-SWIVEL SWIVEL Mounting O-Ring Bracket (Swivel Only) (See Step #9) Depress “Snap-n-Lock” button to fold Non-Swivel legs forward, OR IMPORTANT: Collar down or (See Step #10) Fits AR-15 with ROUND Mil Spec Yoke Assembly rearward Twist knurled knob Swivel Collar Handguards Without Modification. Halves to extend, retract M-4 Requires Additional Hole. or lock legs Fits any Rifle with Sling Swivel Stud OR Assemble Universal Bipod: Counterbore Washer Flat Top Washer 1. After deciding to build non-swivel or swivel bipod, position mounting bracket as shown in picture at right, install either the non-swivel collar or the swivel collar in the assembly. #10 x 3/4 Screws 2. Install non-swivel collar or swivel collar halves onto top side of mounting bracket with Thick Thick pins aligning with holes in mounting bracket. Washer Washer 3. If swivel collar halves were used, place o-ring into groove on top side of mounting bracket. Left Leg Right Leg 4. Install yoke assembly over post on mounting bracket and align (2) pins on bottom of yoke with holes in non-swivel collar or in open area between swivel collar halves. 5. Install washer over the post and secure with the pink pre-coated #10 x 3/4 screw using a Phillips screw driver. NOTE: Non-swivel Bipod will use the washer with the counterbore INSTALLING BIPOD TO RIFLE: top and Swivel Bipod will use the washer with the flat top.
[Show full text]
Fabdefence.Pdf
2012 2-15 grips 16-29 rail systems 30-33 K-pos 34-45 Buttstocks 46-53 TACTICAL FLASHLIGHT ADAPTORS 54-59 Magazine accessories 60-69 parts & upgrades 70-71 Self-Healing Targets 72 index gripsTarget Accuracy AG-43 AGF-43S AR15/M16 Pistol Grip Tactical Folding Pistol Grip for-M16-M4-AR15 Finger Swelts and a Backstrap Shape Designed to Enhance Transforms a Horizontal Positioned Grip to Vertical Position Grip, Even when Wet Weapon Fits Easier in Gun Case and on Weapon Rack Extended Beavertail for Better Control, Allowing a Higher Firmer Hold Provides Easier Maneuverability, more Convenient for Undercover Readily Accessible Storage Area with Securely Sealed Hinged Door Work and Concealment MIL-SPEC Reinforced Polymer Composite Easier and Faster Vehicular Deployment Available in Black and Two Camouflage Colors: Olive Drab Green and Desert Tan Quick Fold/Unfold Button Made From Reinforced Polymer Composite 04 Grips AG-47 AG-58 SG-1 Ergonomic Pistol Grip for AK-47/74 SA. VZ. 58 Pistol Grip Sniper Pistol Grip Advanced Ergonomic Design Prevents Unique Texture Prevents Slipping Replaces Standard Pistol Grip To Provide Wrist Fatigue and Ensures Secure Grip in When Wet Greater Comfort and Operational Control Wet Conditions Advanced Ergonomic Design Advanced Ergonomic Design Improves Trigger Operation Built-In Storage Compartment Adjustable Palm Swell Style Grip Built-In Storage with Removable Enhances Finger to Trigger Correspondence Adapts Easily To Various Sized Hands Cushioned Battery Holder Tough Material & Design Applies Pressure to the Palm of the Hand Manufactured with MIL-SPEC Reinforced Available in Black and Two Camouflage Allowing Deliberate and Measured Polymer Composite Colors: Olive Drab Green, and Desert Tan Trigger Pull Available in Black and Two Camouflage Tough Material & Design Colors: Olive Drab Green, and Desert Tan Available in Black 05 Grips agr-870 agm-500 wg-1911 Remington 870 Pistol Grip Mossberg 500 Pistol Grip 1911 Mag.
[Show full text]