DOCSLIB.ORG

SDS US 2EP Version #: 02 Revision Date: 02-10-2020 Issue Date: 01-15-2018 1 / 8 Response If Swallowed: Rinse Mouth

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
SDS US 2EP Version #: 02 Revision Date: 02-10-2020 Issue Date: 01-15-2018 1 / 8 Response If Swallowed: Rinse Mouth SAFETY DATA SHEET 1. Identification Product identifier Antimony Chloride (SbCl3) Other means of identification SDS number 2EP Materion Code 2EP CAS number 10025-91-9 Synonyms ANTIMONY(III) TRICHLORIDE * Antimony chloride Manufacturer/Importer/Supplier/Distributor information Manufacturer Company name Materion Advanced Chemicals Inc. Address 407 N 13th Street 1316 W. St. Paul Avenue Milwaukee, WI 53233 United States Telephone 414.212.0257 E-mail [email protected] Contact person Laura Hamilton Emergency phone number Chemtrec 800.424.9300 2. Hazard(s) identification Physical hazards Not classified. Health hazards Skin corrosion/irritation Category 1B Serious eye damage/eye irritation Category 1 Specific target organ toxicity, single exposure Category 3 respiratory tract irritation Environmental hazards Hazardous to the aquatic environment, acute Category 2 hazard Hazardous to the aquatic environment, Category 2 long-term hazard OSHA defined hazards Not classified. Label elements Signal word Danger Hazard statement Harmful if swallowed. Causes severe skin burns and eye damage. Causes serious eye damage. May cause respiratory irritation. Suspected of causing genetic defects. Suspected of damaging fertility or the unborn child. May cause damage to organs (). Very toxic to aquatic life. Very toxic to aquatic life with long lasting effects. Precautionary statement Prevention Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Avoid breathing dust/fume/gas/mist/vapors/spray. Wash thoroughly after handling. Do not eat, drink or smoke when using this product. Use only outdoors or in a well-ventilated area. Avoid release to the environment. Wear protective gloves/protective clothing/eye protection/face protection. Material name: Antimony Chloride (SbCl3) SDS US 2EP Version #: 02 Revision date: 02-10-2020 Issue date: 01-15-2018 1 / 8 Response If swallowed: Rinse mouth. Do NOT induce vomiting. If on skin (or hair): Take off immediately all contaminated clothing. Rinse skin with water/shower. If inhaled: Remove person to fresh air and keep comfortable for breathing. If in eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately call a poison center/doctor. Take off contaminated clothing and wash it before reuse. Collect spillage. Storage Store in a well-ventilated place. Keep container tightly closed. Store locked up. Disposal Dispose of contents/container in accordance with local/regional/national/international regulations. Hazard(s) not otherwise None known. classified (HNOC) Supplemental information 100% of the substance consists of component(s) of unknown acute dermal toxicity. For further information, please contact the Product Stewardship Department at +1.800.862.4118. 3. Composition/information on ingredients Substances Chemical name Common name and synonyms CAS number % Antimony Chloride (SbCl3) ANTIMONY(III) TRICHLORIDE 10025-91-9 100 Antimony chloride 4. First-aid measures Inhalation Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a physician or poison control center immediately. Skin contact Take off immediately all contaminated clothing. Take off immediately all contaminated clothing. Rinse skin with water/shower. Call a physician or poison control center immediately. Chemical burns must be treated by a physician. For minor skin contact, avoid spreading material on unaffected skin. Wash contaminated clothing before reuse. Eye contact Immediately flush eyes with plenty of water for at least 15 minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Call a physician or poison control center immediately. Ingestion Call a physician or poison control center immediately. Rinse mouth. Do not induce vomiting. If vomiting occurs, keep head low so that stomach content doesn't get into the lungs. Most important May cause temporary blindness and severe eye damage. Burning pain and severe corrosive skin symptoms/effects, acute and damage. Causes serious eye damage. Corrosive effects. Symptoms may include stinging, tearing, delayed redness, swelling, and blurred vision. Permanent eye damage including blindness could result. May cause respiratory irritation. Indication of immediate medical Provide general supportive measures and treat symptomatically. Chemical burns: Flush with water attention and special treatment immediately. While flushing, remove clothes which do not adhere to affected area. Call an needed ambulance. Continue flushing during transport to hospital. Keep victim warm. Keep victim under observation. Symptoms may be delayed. General information In the case of accident or if you feel unwell, seek medical advice immediately (show the label where possible). IF exposed or concerned: Get medical advice/attention. Ensure that medical personnel are aware of the material(s) involved, and take precautions to protect themselves. Wash contaminated clothing before reuse. 5. Fire-fighting measures Suitable extinguishing media Water fog. Foam. Dry chemical powder. Carbon dioxide (CO2). Unsuitable extinguishing media Do not use water jet as an extinguisher, as this will spread the fire. Specific hazards arising from During fire, gases hazardous to health may be formed. the chemical Special protective equipment Wear suitable protective equipment. and precautions for firefighters Fire fighting Water runoff can cause environmental damage. equipment/instructions Specific methods Use standard firefighting procedures and consider the hazards of other involved materials. General fire hazards No unusual fire or explosion hazards noted. Material name: Antimony Chloride (SbCl3) SDS US 2EP Version #: 02 Revision date: 02-10-2020 Issue date: 01-15-2018 2 / 8 6. Accidental release measures Personal precautions, protective Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Wear equipment and emergency appropriate protective equipment and clothing during clean-up. Do not touch damaged containers procedures or spilled material unless wearing appropriate protective clothing. Ensure adequate ventilation. Local authorities should be advised if significant spillages cannot be contained. For personal protection, see section 8 of the SDS. Methods and materials for Prevent entry into waterways, sewer, basements or confined areas. containment and cleaning up Large Spills: Stop the flow of material, if this is without risk. Dike the spilled material, where this is possible. Absorb in vermiculite, dry sand or earth and place into containers. Following product recovery, flush area with water. Small Spills: Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to remove residual contamination. Never return spills to original containers for re-use. For waste disposal, see section 13 of the SDS. Environmental precautions Avoid release to the environment. Inform appropriate managerial or supervisory personnel of all environmental releases. Do not contaminate water. Avoid discharge into drains, water courses or onto the ground. 7. Handling and storage Precautions for safe handling Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Do not get in eyes, on skin, or on clothing. Do not taste or swallow. Do not get this material on clothing. Avoid contact during pregnancy/while nursing. Avoid prolonged exposure. When using, do not eat, drink or smoke. Provide adequate ventilation. Wear appropriate personal protective equipment. Wash hands thoroughly after handling. Avoid release to the environment. Do not empty into drains. Observe good industrial hygiene practices. Conditions for safe storage, Store locked up. Store in a cool, dry place out of direct sunlight. Store in tightly closed container. including any incompatibilities Store away from incompatible materials (see Section 10 of the SDS). 8. Exposure controls/personal protection Occupational exposure limits The following constituents are the only constituents of the product which have a PEL, TLV or other recommended exposure limit. At this time, the other constituents have no known exposure limits. US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000) Material Type Value Antimony Chloride (SbCl3) PEL 0.5 mg/m3 (CAS 10025-91-9) US. ACGIH Threshold Limit Values Material Type Value Antimony Chloride (SbCl3) TWA 0.5 mg/m3 (CAS 10025-91-9) US. NIOSH: Pocket Guide to Chemical Hazards Material Type Value Antimony Chloride (SbCl3) TWA 0.5 mg/m3 (CAS 10025-91-9) US. California Code of Regulations, Title 8, Section 5155. Airborne Contaminants Material Type Value Antimony Chloride (SbCl3) PEL 0.5 mg/m3 (CAS 10025-91-9) Biological limit values No biological exposure limits noted for the ingredient(s). Material name: Antimony Chloride (SbCl3) SDS US 2EP Version #: 02 Revision date: 02-10-2020 Issue date: 01-15-2018 3 / 8 Appropriate engineering controls Good general ventilation should be used. Ventilation rates should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation, or other engineering controls to maintain airborne levels below recommended exposure limits. If exposure limits have not been established, maintain airborne levels to an acceptable level. Eye wash facilities and emergency shower must be available when handling this product. Individual protection measures, such as personal protective equipment Eye/face protection Wear eye/face protection.
Load more

Recommended publications
  • Material Safety Data Sheet
    Material Safety Data Sheet Antimony trichloride, reagent ACS, crystals, 99+% ACC# 00252 Section 1 - Chemical Product and Company Identification MSDS Name: Antimony trichloride, reagent ACS, crystals, 99+% Catalog Numbers: AC401370000, AC401370050, AC401371000, AC401375000 Synonyms: Trichlorostibine; Antimonous chloride; Antimony(III) chloride; Antimony trichloride. Company Identification: Acros Organics N.V. One Reagent Lane Fair Lawn, NJ 07410 For information in North America, call: 800-ACROS-01 For emergencies in the US, call CHEMTREC: 800-424-9300 Section 2 - Composition, Information on Ingredients CAS# Chemical Name Percent EINECS/ELINCS 10025-91-9 Antimony(III) chloride >99 233-047-2 Section 3 - Hazards Identification EMERGENCY OVERVIEW Appearance: white solid. Danger! Corrosive. Causes severe eye and skin burns. Causes severe digestive and respiratory tract burns. May be harmful if swallowed. Moisture sensitive. Hygroscopic (absorbs moisture from the air). Target Organs: Lungs, cardiovascular system, eyes, skin, mucous membranes. Potential Health Effects Eye: Causes eye burns. Skin: Causes skin burns. Ingestion: Causes gastrointestinal tract burns. May be harmful if swallowed. Inhalation: Causes chemical burns to the respiratory tract. May cause lung damage. May produce cardiovascular effects. Chronic: Chronic exposure may cause liver damage. Section 4 - First Aid Measures Eyes: In case of contact, immediately flush eyes with plenty of water for a t least 15 minutes. Get medical aid immediately. Skin: In case of contact, immediately flush skin with plenty of water for at least 15 minutes while removing contaminated clothing and shoes. Get medical aid immediately. Wash clothing before reuse. Ingestion: If swallowed, do NOT induce vomiting. Get medical aid immediately. If victim is fully conscious, give a cupful of water.
    [Show full text]
  • CAS No.) Screening Justification Is Public Comment Now Open? CAS No
    EGLE Air Quality Division (AQD) Air Toxics Screening Level Justifications (Numerically by CAS No.) Screening Justification Is Public Comment Now Open? CAS No. Chemical Name Level & Responses Info E-Mail AQD Deadline None ad acid View View Not Open for Public Comment None amyl acetate (mixture) View View Not Open for Public Comment None atlox 848 View View Not Open for Public Comment None biosam tp-1.5 View View Not Open for Public Comment None calcium chloride View View Not Open for Public Comment None epoxy resin solution View View Not Open for Public Comment None heptamethyl-1-vinyl-1,7-dichlorotetrasilazane View View Not Open for Public Comment None n-butylglucamine View View Not Open for Public Comment None n-chloro-2,6-difluorobenzamide View View Not Open for Public Comment None trichloroethylene View View Not Open for Public Comment None triethylammonium suleptanate View View Not Open for Public Comment 50-00-0 formaldehyde View View Not Open for Public Comment 50-03-3 hydrocortisone acetate View View Not Open for Public Comment 50-21-5 lactic acid View View Not Open for Public Comment 50-28-2 estradiol View View Not Open for Public Comment 50-29-3 ddt View View Not Open for Public Comment 50-32-8 benzo(a)pyrene View View Not Open for Public Comment 51-28-5 2,4-dinitrophenol View View Not Open for Public Comment 53-36-1 methyl predisolone acetate View View Not Open for Public Comment 53-70-3 dibenz(a,h)anthracene View View Not Open for Public Comment 56-23-5 carbon tetrachloride View View Not Open for Public Comment 56-49-5 3-methylcholanthrene View View Not Open for Public Comment 56-55-3 benz(a)anthracene View View Not Open for Public Comment 56-81-5 glycerol View View Not Open for Public Comment 57-11-4 stearic acid View View Not Open for Public Comment Revised Monday, September 27, 2021 Page 1 of 51 EGLE Air Quality Division (AQD) Air Toxics Screening Level Justifications (Numerically by CAS No.) Screening Justification Is Public Comment Now Open? CAS No.
    [Show full text]
  • The Colorimetric Reaction Between Vitamin A2 Aldehyde and Antimony Trichloride
    556 A. W. PHILLIPS AND P. A. GIBBS 1961 logical properties of peptides derived from casein The authors wish to thank Dr D. A. H. Hearfield for reflected more specific differences in chemical details of the assay and inoculum media, Dr A. J. Woiwod constitution. and Mr R. Knight for constructing the high-voltage power pack, and Miss E. M. Anderson for her able technical STMMARY assistance. 1. Columns of Sephadex G-25 have been used REFERENCES for the fractionation preliminary of tryptic digests Cole, S. W. & Onslow, H. (1916). Lancet, ii, 9. of casein. Gladstone, G. P. & Fildes, P. (1940). Brit. J. exp. Path. 21, 2. Fractions from Sephadex columns have been 161. examined for their ability to stimulate the growth Green, A. A. (1933). J. Amer. chem. Soc. 55, 2331. of a strain of Streptococcus equi8imili8. Maximum Hearfield, D. A. H. & Phillips, A. W. (1961). Nature, Lond., stimulatory activity appeared to be localized in a 190, 266. fairly narrow region of the total peptide material. Ingram, V. M. (1958). Biochim. biophys. Acta, 28, 546. 3. Further fractionation of peptides derived Katz, A. M., Dreyer, W. J. & Anfinsen, C. B. (1959). from casein has been achieved by subjecting frac- J. biol. Chem. 234, 2897. Merrifield, R. B. & Woolley, D. W. (1958). J. Amer. chem. tions from columns of Sephadex to two-dimensional Soc. 80, 6635. separations involving the successive use of paper Porath, J. (1960). Biochim. biophy8. Acta, 39, 193. chromatography and high-voltage electrophoresis. Woiwod, A. J. (1949). J. gen. Microbiol. 3, 312. Over one hundred spots due to peptides have been Woiwod, A.
    [Show full text]
  • Antimony Trioxide [CAS No. 1309-64-4]
    Antimony Trioxide [CAS No. 1309-64-4] Brief Review of Toxicological Literature Prepared for National Toxicology Program (NTP) National Institute of Environmental Health Sciences (NIEHS) National Institutes of Health U.S. Department of Health and Human Services Contract No. N01-ES-35515 Project Officer: Scott A. Masten, Ph.D. NTP/NIEHS Research Triangle Park, North Carolina Prepared by Integrated Laboratory Systems, Inc. Research Triangle Park, North Carolina July 2005 Chemical Name: Antimony Trioxide CAS RN: 1309-64-4 Formula: Sb2O3 Basis for Nomination: Antimony trioxide was nominated by the National Institute of Environmental Health Sciences for chronic toxicity, cardiotoxicity and carcinogenicity studies due to the potential for substantial human exposure in occupational settings and lack of adequate two-year exposure carcinogenicity studies. Additional studies of antimony trioxide are of interest, in lieu of studies with antimony trisulfide or another antimony compound, considering the higher volume of use and magnitude of human exposure, and the lack of two- year exposure carcinogenicity studies for any antimony compound by any route of administration. Antimony trisulfide was nominated to the NTP by the National Cancer Institute in 2002 for carcinogenicity studies (http://ntp.niehs.nih.gov/ntpweb/index.cfm?objectid=25BEBA08-BDB7-CEBA- FC56EAD78615ADCF). Subsequent to the nomination review process, the NTP concluded that antimony trisulfide should not be studied further at this time for the following reasons: 1) antimony trisulfide does not appear to represent a major form of antimony to which humans are exposed; 2) carcinogenicity studies of antimony trisulfide is unlikely to lead to a sufficient understanding of the carcinogenicity hazard for antimony compounds as a group; and 3) there is concern regarding the safe handling of pure antimony trisulfide in experimental settings due to its flammable/combustible nature.
    [Show full text]
  • Ionization of Some Inorganic Halides in Chlorosulphuric Acid Solvent System-Redox Reactions of Phosphorus, Arsenic & Antimony Halides in Chlorosulphuric Acid
    Indian Journal of Chemistry Vol. 20A, August 1981, pp. 773-776 Ionization of Some Inorganic Halides in Chlorosulphuric Acid Solvent System-Redox Reactions of Phosphorus, Arsenic & Antimony Halides in Chlorosulphuric Acid Z. A. SIDDIQI·, MOHAMMAD ASLAM, N. A. ANSARI, M. SHAKIR & S. A. A. ZAIDI Chemistry Department, Aligarh Muslim University, Aligarh 202 001 Received 13 October 1980; revised and accepted 29 November 1980 The behaviour of solutes, viz. phosphorus trichloride, tribromide, pentachloride, pentabromide and hexachloro- iodide in HS03CI has been investigated conductometrically. While the pentahalides and bexacbloroiodide ionise pro- ducing the stable cationic species PX~, tbe trihalides are oxidized producing ultimately the conjugate acid POH+X. in tbis solvent, The conductometric redox titrations of phosphorus trihalides with the appropriate halogens and inter- halogen (ICI) compounds indicate the formation of cationic species PCI3Br+ and PBr.CI+ as stable entities in solutions. Solutes like AsCI•• SbF. and SbCI. are only partially ionised whereas SbCI •• BiCI. and VCla remain insoluble in this solvent. The basic ionization constants ofthe partially ionizing solutes have also been evaluated. Tis quite well known- that the interaction of the sulphuric acid19 give fairly conducting solutions stoichiometric amount of the appropriate halogen (Fig. 1) in chlorosulphuric acid; the conductivity Iwith a few binary phosphorus(III) halides in gradually increases with time and attains a stable non-polar solvent like carbon tetrachloride increases value on standing for a few minutes. The average the oxidation state of phosphorus resulting in the y-values of the stable solutions have been found to formation of the corresponding mixed phosphorus(V) be 0.20 and 0.80 respectively indicating the formation halides.
    [Show full text]
  • List of Lists
    United States Office of Solid Waste EPA 550-B-10-001 Environmental Protection and Emergency Response May 2010 Agency www.epa.gov/emergencies LIST OF LISTS Consolidated List of Chemicals Subject to the Emergency Planning and Community Right- To-Know Act (EPCRA), Comprehensive Environmental Response, Compensation and Liability Act (CERCLA) and Section 112(r) of the Clean Air Act • EPCRA Section 302 Extremely Hazardous Substances • CERCLA Hazardous Substances • EPCRA Section 313 Toxic Chemicals • CAA 112(r) Regulated Chemicals For Accidental Release Prevention Office of Emergency Management This page intentionally left blank. TABLE OF CONTENTS Page Introduction................................................................................................................................................ i List of Lists – Conslidated List of Chemicals (by CAS #) Subject to the Emergency Planning and Community Right-to-Know Act (EPCRA), Comprehensive Environmental Response, Compensation and Liability Act (CERCLA) and Section 112(r) of the Clean Air Act ................................................. 1 Appendix A: Alphabetical Listing of Consolidated List ..................................................................... A-1 Appendix B: Radionuclides Listed Under CERCLA .......................................................................... B-1 Appendix C: RCRA Waste Streams and Unlisted Hazardous Wastes................................................ C-1 This page intentionally left blank. LIST OF LISTS Consolidated List of Chemicals
    [Show full text]
  • PROVISIONAL PEER REVIEWED TOXICITY VALUES for SOLUBLE ANTIMONY COMPOUNDS (VARIOUS Casrns)
    EPA/690/R-08/020F l Final 7-29-2008 Provisional Peer Reviewed Toxicity Values for Soluble Antimony Compounds (Various CASRNs) Superfund Health Risk Technical Support Center National Center for Environmental Assessment Office of Research and Development U.S. Environmental Protection Agency Cincinnati, OH 45268 Acronyms and Abbreviations bw body weight cc cubic centimeters CD Caesarean Delivered CERCLA Comprehensive Environmental Response, Compensation and Liability Act of 1980 CNS central nervous system cu.m cubic meter DWEL Drinking Water Equivalent Level FEL frank-effect level FIFRA Federal Insecticide, Fungicide, and Rodenticide Act g grams GI gastrointestinal HEC human equivalent concentration Hgb hemoglobin i.m. intramuscular i.p. intraperitoneal IRIS Integrated Risk Information System IUR inhalation unit risk i.v. intravenous kg kilogram L liter LEL lowest-effect level LOAEL lowest-observed-adverse-effect level LOAEL(ADJ) LOAEL adjusted to continuous exposure duration LOAEL(HEC) LOAEL adjusted for dosimetric differences across species to a human m meter MCL maximum contaminant level MCLG maximum contaminant level goal MF modifying factor mg milligram mg/kg milligrams per kilogram mg/L milligrams per liter MRL minimal risk level MTD maximum tolerated dose MTL median threshold limit NAAQS National Ambient Air Quality Standards NOAEL no-observed-adverse-effect level NOAEL(ADJ) NOAEL adjusted to continuous exposure duration NOAEL(HEC) NOAEL adjusted for dosimetric differences across species to a human NOEL no-observed-effect level OSF
    [Show full text]
  • Antimony Chloride.Pdf
    He alth 3 0 Fire 0 3 1 Re activity 1 Personal Protection J Material Safety Data Sheet Antimony trichloride MSDS Section 1: Chemical Product and Company Identification Product Name: Antimony trichloride Contact Information: Catalog Codes: SLA3439 Sciencelab.com, Inc. 14025 Smith Rd. CAS#: 10025-91-9 Houston, Texas 77396 RTECS: CC4900000 US Sales: 1-800-901-7247 International Sales: 1-281-441-4400 TSCA: TSCA 8(b) inventory: Antimony trichloride Order Online: ScienceLab.com CI#: Not available. CHEMTREC (24HR Emergency Telephone), call: Synonym: Antimonous Chloride; Antimony chloride; 1-800-424-9300 Antimony butter; Butter of antimony; Trichlorostibine International CHEMTREC, call: 1-703-527-3887 Chemical Name: Antimony (III) Chloride For non-emergency assistance, call: 1-281-441-4400 Chemical Formula: SbCl3 Section 2: Composition and Information on Ingredients Composition: Name CAS # % by Weight Antimony trichloride 10025-91-9 100 Toxicological Data on Ingredients: Antimony trichloride: ORAL (LD50): Acute: 525 mg/kg [Rat]. 574 mg/kg [Guinea pig]. Section 3: Hazards Identification Potential Acute Health Effects: Very hazardous in case of skin contact (irritant), of eye contact (irritant), of ingestion, of inhalation. Hazardous in case of skin contact (corrosive), of eye contact (corrosive). Slightly hazardous in case of skin contact (permeator). The amount of tissue damage depends on length of contact. Eye contact can result in corneal damage or blindness. Skin contact can produce inflammation and blistering. Inhalation of dust will produce irritation to gastro-intestinal or respiratory tract, characterized by burning, sneezing and coughing. Severe over-exposure can produce lung damage, choking, unconsciousness or death. Inflammation of the eye is characterized by redness, watering, and itching.
    [Show full text]
  • Antimony(III) Chloride Creation Date 12
    SAFETY DATA SHEET according to Regulation (EC) No 1907/2006 (REACH) as amended Antimony(III) chloride Creation date 12. September 2019 Revision date Version 1.0 SECTION 1: Identification of the substance/mixture and of the company/undertaking 1.1. Product identifier Antimony(III) chloride Substance / mixture substance Chemical name antimony trichloride CAS number 10025-91-9 Index number 051-001-00-8 EC (EINECS) number 233-047-2 1.2. Relevant identified uses of the substance or mixture and uses advised against Substance's intended use Chemical production, analytical chemistry, laboratory synthesis, industrial applications. Substance uses advised against The product should not be used in ways other then those referred in Section 1. Chemical safety report 1.3. Details of the supplier of the safety data sheet Supplier Name or trade name Ing. Petr Švec - PENTA s.r.o. Address Radiová 1122/1, Praha 10, 102 00 Czech Republic Identification number (CRN) 02096013 VAT Reg No CZ02096013 Phone +420 226 060 681 E-mail [email protected] Web address www.pentachemicals.eu Competent person responsible for the safety data sheet Name Ing. Petr Švec - PENTA s.r.o. E-mail [email protected] 1.4. Emergency telephone number National Health Service (NHS) 111 National poisoning information centre Scotland, NHS 24: 111 SECTION 2: Hazards identification 2.1. Classification of the substance or mixture Classification of the substance in accordance with Regulation (EC) No 1272/2008 The substance is classified as dangerous. Skin Corr. 1B, H314 Aquatic Chronic 2, H411 Full text of all classifications and hazard statements is given in the section 16.
    [Show full text]
  • Data Sheet According to 1907/2006/EC, Article 31 Printing Date 21.07.2021 Revision: 21.07.2021
    Page 1/7 Safety data sheet according to 1907/2006/EC, Article 31 Printing date 21.07.2021 Revision: 21.07.2021 SECTION 1: Identification of the substance/mixture and of the company/undertaking · 1.1 Product identifier · Trade name: Antimony(III) chloride (99%-Sb) · Item number: 93-5131 · CAS Number: 10025-91-9 · EC number: 233-047-2 · Index number: 051-001-00-8 · 1.2 Relevant identified uses of the substance or mixture and uses advised against No further relevant information available. · 1.3 Details of the supplier of the safety data sheet · Manufacturer/Supplier: Strem Chemicals, Inc. 7 Mulliken Way NEWBURYPORT, MA 01950 USA [email protected] · Further information obtainable from: Technical Department · 1.4 Emergency telephone number: EMERGENCY: CHEMTREC: + 1 (800) 424-9300 During normal opening times: +1 (978) 499-1600 SECTION 2: Hazards identification · 2.1 Classification of the substance or mixture · Classification according to Regulation (EC) No 1272/2008 d~ GHS05 corrosion Skin Corr. 1B H314 Causes severe skin burns and eye damage. d~ GHS09 environment Aquatic Chronic 2 H411 Toxic to aquatic life with long lasting effects. · 2.2 Label elements · Labelling according to Regulation (EC) No 1272/2008 The substance is classified and labelled according to the CLP regulation. · Hazard pictograms d~d~ GHS05 GHS09 · Signal word Danger · Hazard-determining components of labelling: antimony trichloride · Hazard statements H314 Causes severe skin burns and eye damage. (Contd. on page 2) GB 44.1.1 Page 2/7 Safety data sheet according to 1907/2006/EC, Article 31 Printing date 21.07.2021 Revision: 21.07.2021 Trade name: Antimony(III) chloride (99%-Sb) (Contd.
    [Show full text]
  • Views Concerning the Actual Transfer of the Electrons Have Been Advanced in Recent Years
    I [r L ACCELERATSC‘M (7F THE ELEC‘E‘RGH EXCHANGE REACHON EEH‘V‘EEN fit‘é‘i’EMGNY ":‘mcaémmsz AND AM'E‘tMONY PENTACHLGRWE EN $213213?! ‘E‘E‘E‘MxCHEQRE‘rE BY maa‘rzow $5: AMWDRGUS E’WDRQ‘GEN CHLGREEDE Thasis far {“515 Degree of M. S. MECHiGAN STATE 5.}.‘WERSETY Kamafh PM @rice E955 THESIS D QQ LIBRARY Michigan State University 1 ABSTRACT ACCELERATION OF THE ELECTRON EXCHANGE REACTION BETWEEN ANTINONY TRICHLORIDE AND ANTINONY PENTACHLORIDE IN CARBON TETRACHLORIDE BY ADDITION OF ANHYDROUS HYDROGEN CHLORIDE F". by Kenneth R. Price The electron exchange reaction between antimony tri- chloride and antimony pentachloride in anhydrous carbon tetrachloride has been studied in the presence of added 5 anhydrous hydrogen chloride. In the absence of hydrogen chloride, Barker and Kahn (1) found the exchange to proceed by two paths; one path depended only on the concentration of antimony pentachloride and the other depended on the concentration of antimony trichloride and the concentration of antimony pentachloride squared. The addition of hydrogen chloride waa found to acceler— ate the exchange reaction beyond 4L that yredicted from the Barker and Kahn paths. A complex rate law was found that indicated a contribution by the Barker and Katy paths plus a new path involving the hydrogen chloride. This third path involves antimony trichloride and hexachloroantimonic(V) acid. The rate law found was: 1F. B. Barker and M. Kahn, J. Am. Chem. 393., 78, 1317 (1956). Kenneth R. Price - ‘ ' -4 2 a = 1.6 x 10 7 [SbClR] + 1.8 x 10 [SbClB] [SbClR] + 2.5 x 10‘5 tSbCl3] [HSbCl6] The mechanism proposed involves the formation of a triply chloro—bridged diantimonate species consisting of two octahedra Joined face to face.
    [Show full text]
  • Chemical Compatibility Reference Guide
    TM QUICK REFERENCE GUIDE 1 Chemical Compatibility Chart for Helix® Acetal Blends www.helixlinear.com • 855-435-4958 Chemical Rating Chemical Rating Chemical Rating Chemical Rating Acetaldehyde A Aluminum Potassium Sulfate 10% C Antimony Trichloride N/A Butane A Acetamide A Aluminum Potassium Sulfate 100% C Aqua Regia (80% HCl, 20% HNO3) D Butanol (Butyl Alcohol) A Acetate Solvent N/A Aluminum Sulfate A1 Arochlor 1248 N/A Butter A Acetic Acid 5% C Alums N/A Aromatic Hydrocarbons A Buttermilk A Acetic Acid 20% D Amines D Arsenic Acid D Butyl Amine C1 Acetic Acid 80% D Ammonia 10% D Arsenic Salts N/A Butyl Ether D Acetic Acid, Glacial D Ammonia Nitrate C Asphalt B2 Butyl Phthalate N/A Acetic Anhydride D Ammonia, anhydrous D Barium Carbonate A Butylacetate A Acetone A Ammonia, liquid D Barium Chloride A Butylene A Acetyl Bromide N/A Ammonium Acetate N/A Barium Cyanide B Butyric Acid A Acetyl Chloride (dry) D Ammonium Bifluoride D Barium Hydroxide D Calcium Bisulfate N/A Acetylene A Ammonium Carbonate D Barium Nitrate B2 Calcium Bisulfide D Acrylonitrile N/A Ammonium Caseinate D Barium Sulfate B2 Calcium Bisulfite D Adipic Acid 5% A Ammonium Chloride B Barium Sulfide A Calcium Carbonate A Alcohols: Amyl A Ammonium Hydroxide D Beer A1 Calcium Chlorate A Alcohols: Benzyl A Ammonium Nitrate A2 Beet Sugar Liquids B Calcium Chloride D Alcohols: Butyl A Ammonium Oxalate B Benzaldehyde A Calcium Chloride 5% B1 Alcohols: Diacetone A Ammonium Persulfate D Benzene A Calcium Hydroxide D Alcohols: Ethyl A1 Ammonium Phosphate, Dibasic B2 Benzene Sulfonic
    [Show full text]