USB3.0 SD Card Reader

User’s Manual

Multi Card Reader User’s Manual

Safety Instructions

Always read the safety instructions carefully

„ Keep this User’s Manual for future reference

„ Keep this equipment away from humidity „ If any of the following situation arises, get the equipment checked by a service technician: • The equipment has been exposed to moisture. • The equipment has been dropped and damaged. • The equipment has obvious sign of breakage. • The equipment has not been working well or you cannot get it work according to User’s Manual.

Copyright Statement

No part of this publication may be reproduced in any form by any means without the prior written permission. Other trademarks or brand names mentioned herein are trademarks or registered trademarks of their respective companies.

Disclaimer

Information in this document is subject to change without notice. The manufacturer does not make any representations or warranties (implied or otherwise) regarding the accuracy and completeness of this document and shall in no event be liable for any loss of profit or any commercial damage, including but not limited to special, incidental, consequential, or other damage.

i Table of Contents Table of Contents

1. Introduction ...... 3 Features...... 3 Package Contents...... 3 System Requirements...... 3 LED Status...... 3

2 Specifications...... 4

3. Regulatory Compliance ...... 5 FCC Conditions ...... 5 CE...... 5 WEEE Information ...... 5

ii 1. Introduction

1. Introduction

This USB 3.0 SD card reader controller is based upon universal Serial Bus 3.0 specification, which integrates USB3.0 & USB2.0 Transceiver, MCU, SIE regulator and memory card access units into a single chip. It can link in Super speed, High Speed, or Full Speed operation and support USB2.0/USB3.0 power saving mode. Beside, this also supports both the internal MCU program ROM, and external serial flash memory interface. With the external serial flash memory interface, the firmware could be easily updated through USB link. This SD card reader integrate all regulator, clock generation circuitry and MOSFET components for switching card power, and also dramatically reduce the system cost.

Package Contents Before installation, please check the items of the package.

„ SD Card Reader x1 „ User Manual x1

System Requirements „ Support full USB 3.0 speed at Windows® 7, Windows Vista®, Windows® XP

3 Multi Card Reader User’s Manual

LED Status

LED Color Description

Power Green On: To confirm a proper connection.

4 2. Specifications

2. Specifications

„ USB compliance

- Comply with USB3.0

- Comply with USB2.0 rev 2.0

- Comply with USB Mass storage class specification rev 1.0

-Comply with SD part 1 Physical Layer specification Version 3.0

- Comply with Multimedia Card system Specification version 4.4

„ Memory card support

- Support Secure Digital (SD) Multi Media Card (MMC), Mini SD, Micro SD (T-Flash), SDHC, SDXC (up to 2TB), RS-MMC, Mobile MMC and MMC-Micro

„ Support SD card clock 208MHz (max.) forSDR104 mode.

„ Support SD card clock 100 MHz (Max.) for SDR50 Model.

„ Support SD card clock 50MHz (max.) for DDR50 model.

„ Support Hardware ECC (Error Correction Code)

„ Support Hardware CRC (Cyclic Redundancy Check) function

„ USB Bus power operation

„ Support USB2.0/USB3.0 power saving mode.

„ Support control, Bulk IN/OUT data pipes.

„ Integrated Fast 8051 processor.

„ External serial EEPROM 93C46 interface.

„ Support Spread Spectrum Clock for SD/MMC to reduce EMI effect.

„ Storage Temperature: -10 ℃ to +60℃

5 Multi Card Reader User’s Manual 3. Regulatory Compliance

FCC Conditions

This equipment has been tested and found to comply with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference

(2) This device must accept any interference received. Including interference that may cause undesired operation.

CE

This equipment is in compliance with the requirements of the following regulations: EN 55 022: CLASS B

WEEE Information

For EU (European Union) member users: According to the WEEE (Waste electrical and electronic equipment) Directive, do not dispose of this product as household waste or commercial waste. Waste electrical and electronic equipment should be appropriately collected and recycled as required by practices established for your country. For information on recycling of this product, please contact your local authorities, your household waste disposal service or the shop where you purchased the product.

6