DOCSLIB.ORG

USESI 691453 Catalog.Pdf

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
USESI 691453 Catalog.Pdf Tech at-a-Glance Flammability Ratings for Copper Cables Cable jacket ratings for copper cabling combine a wide range of terms, some of which may be more common than others depending upon location: CMX, CM, CMG, CMR and CMP. Jacket Types Per NFPA-70, the National Electric Code (NEC article 500), identifies the location where each cable type is to be used. • CMP (PLENUM): Suitable for use in ducts, plenums, and other spaces used for environmental air and shall also be listed as having adequate fire-resistant and low smoke-producing characteristics. These cables are also referenced in Canadian Standards as CSA FT6. • CMR (RISER): Suitable for use in a vertical run in a shaft or from floor to floor and shall also be listed as having fire-resistant characteristics capable of preventing the carrying of fire from floor to floor. • CMG (GENERAL PURPOSE): Suitable for general-purpose communications use, with the exception of risers and plenums, and shall also be listed as being resistant to the spread of fire. These cables are also referenced in Canadian Standards as CSA FT4. • CM (GENERAL PURPOSE): Suitable for general-purpose communications use, with the exception of risers and plenums, and shall also be listed as being resistant to the spread of fire. These cables are also referenced in Canadian Standards as CSA FT4. • CMX (LIMITED USE): Suitable for use in dwellings and for use in raceway and shall also be listed as being resistant to flame spread. As the flammability and smoke requirements for cables become more rigorous from CMX to CMP, the NEC also offers a cable substitution hierarchy (see Figure 1) to allow the use of more stringent requirement cables in place of a less rigid cable. For instance, a CMR or CMP cable could be replaced for a CM or CMG cable. DESCRIPTION TYPE TEST METHOD Plenum CMP NFPA 262-2007 Riser CMR UL 1666-2002 General Purpose CMG/CM UL 1685-2000* or CSA C22.2 No. 0.3-M-2001 *UL1685-2000 applies to CM cable only Limited Use CMX UL1581-2001 (VW-1 Flame Test) A Cable A shall be permitted to be used in place of cable B Figure 1: NEC Cable Substitution Hierarchy B 2 www.vericomsolutions.com Table of Contents Bulk Wire Installation Supplies Category Cable 4-13 Boots & Connectors 50,51 Coaxial Cable 14-18 Mounting & Hardware 51 Fire Alarm Cable 19,20 Tools & Testers 52 Irrigation & Control Wire 21,22 Wire Management 53 Media Cable 23,24 Security Cable 25-29 Power Products Speaker Cable 30 Power Adapters 54,55 Thermostat Cable 31-33 Power Cords 56 Cables & Adapters Surge Protectors 56 Audio / Video Cables 34 Racks, Cabinets & Accessories Coaxial Cables 35 Relay Racks 57-59 Ethernet Cables 36-38 Wall Mount Cabinets 60,61 USB Cables 39 Floor Cabinets 62-64 HDMI Cables 40,41 Cabinet & Rack Feature Comparison 65 Adapters 42,43 Cabinet & Rack Accessories 66-76 Flat Panel TV Mounts Splitters Low Profile TV Mounts 44 Splitters 900 MHz 77 Tilting TV Mounts 45 Splitters 3000 MHz 77 Full Motion TV Mounts 46,47 Desk & Ceiling Mounts 48 Wall Plates Grounding Products Decora Style Wall Plates & Kits 78 Keystone Wall Plates & Inserts 79 Ground Wire 49 Keystone Inserts 80 Grounding Supplies 49 Standard Wall Plates 81 Midsize Wall Plates 82 Surface Mounts 83 Although Vericom makes every reasonable effort to ensure their accuracy at the time of this publication, information, images and specifications herein are subject to error or omission and to change without notice, and the listing of such information and specifications does not ensure product availability. 865.671.4455 3 Category Cable CAT3 2P Unshielded CM Premise Cable P1 White-Blue / Blue P2 White-Orange / Orange Available Put-Ups ∙1000’ Pull Box Available Colors Applications • 10BASE-T Networks • Telecommunications • Indoor *Colors are for representative purposes only. Actual product hues may vary. • Commercial/Residential SPECIFICATIONS Compliances Cable Construction 24 AWG U/UTP x 2P Jacket Type CM • RoHS Compliant Conductor Material SBC Overall Temp. Rating 75° C • ISO/IEC 11801 Insulation Material HDPE Voltage Rating 300 V • TIA/EIA-568-C.2 Ripcord Yes Impedence 1-16 MHz 100 ± 15 Ω Features Jacket Material PVC • Tested To 100 MHz STANDARDS COMPLIANCE • Twisted Pairs To Reduce Crosstalk RoHS Compliant ISO/IEC 11801 TIA/EIA 568-C.2 Category 3 Cable • Easy to Use Pull Box AVAILABILITY • Footage Markers on Cable Jacket ITEM # AVAILABLE COLOR • Colors: Gray and Beige MBW3U-01633 Gray MBW3U-03580 Beige BULK WIRE CAT3 3P Unshielded CM Premise Cable P1 White-Blue / Blue P2 White-Orange / Orange P3 White-Green / Green Available Put-Ups ∙1000’ Pull Box Available Colors Applications • 10BASE-T Networks • Telecommunications • Indoor *Colors are for representative purposes only. Actual product hues may vary. • Commercial/Residential SPECIFICATIONS Compliances Cable Construction 24 AWG U/UTP x 3P Jacket Type CM • RoHS Compliant Conductor Material SBC Overall Temp. Rating 75° C • ISO/IEC 11801 Insulation Material HDPE Voltage Rating 300 V • TIA/EIA-568-C.2 Ripcord Yes Impedence 1-16 MHz 100 ± 15 Ω Features Jacket Material PVC • Tested To 100 MHz STANDARDS COMPLIANCE • Twisted Pairs To Reduce Crosstalk RoHS Compliant ISO/IEC 11801 TIA/EIA 568-C.2 Category 3 Cable • Easy to Use Pull Box AVAILABILITY • Footage Markers on Cable Jacket ITEM # AVAILABLE COLOR • Color: Gray MBW3U-04141 Gray 4 www.vericomsolutions.com Category Cable CAT5e Unshielded CM Premise Cable P1 White-Blue / Blue P2 White-Orange / Orange P3 White-Green / Green P4 White-Brown / Brown Available Put-Ups ∙1000’ Pull Box Applications Available Colors • 10/100/1000BASE-T Networks • Telecommunications • LAN *Colors are for representative purposes only. • Indoor Actual product hues may vary. • Commercial/Residential SPECIFICATIONS Compliances Cable Construction 24 AWG U/UTP x 4P Jacket Type CM • c(UL)us Listed Conductor Material SBC Overall Temp. Rating 75° C • RoHS Compliant Insulation Material HDPE Voltage Rating 300 V • ISO/IEC 11801 Ripcord Yes Impedence 1-350 MHz 100 ± 15 Ω • TIA/EIA-568-C.2 Jacket Material PVC Features STANDARDS COMPLIANCE • Tested to 350 MHz c(UL)us Listed RoHS Compliant ISO/IEC 11801 TIA/EIA 568-C.2 Category 5e Cable • Twisted Pairs to Reduce Crosstalk AVAILABILITY • Easy to Use Pull Box ITEM # AVAILABLE COLOR • Footage Markers on Cable Jacket MBW5U-01531 Blue • Colors: Blue CAT5e Unshielded ETL Listed CMR Premise Cable P1 White-Blue / Blue P2 White-Orange / Orange BULK WIRE P3 White-Green / Green P4 White-Brown / Brown Available Put-Ups ∙1000’ Pull Box Applications Available Colors • 10/100/1000BASE-T Networks • Telecommunications • LAN *Colors are for representative purposes only. • Indoor Actual product hues may vary. • Commercial/Residential SPECIFICATIONS Compliances Cable Construction 24 AWG U/UTP x 4P Jacket Type CMR • ETL Listed Type CMR Conductor Material SBC Overall Temp. Rating 75° C • ETL Verified Insulation Material HDPE Voltage Rating 300 V • RoHS Compliant Ripcord Yes Impedence 1-350 MHz 100 ± 15 Ω • ISO/IEC 11801 Jacket Material FRPVC • TIA/EIA-568-C.2 STANDARDS COMPLIANCE Features ETL Listed / Verified RoHS Compliant ISO/IEC 11801 TIA/EIA 568-C.2 Category 5e Cable • Tested to 350 MHz AVAILABILITY • Twisted Pairs to Reduce Crosstalk ITEM # AVAILABLE COLOR • Easy to Use Pull Box XBW5U-03596 Blue • Footage Markers on Cable Jacket XBW5U-03597 White • Colors: Blue and White 865.671.4455 5 Category Cable CAT5e Unshielded CMR Premise Cable P1 White-Blue / Blue P2 White-Orange / Orange P3 White-Green / Green P4 White-Brown / Brown Available Put-Ups ∙1000’ Pull Box Available Colors Applications • 10/100/1000BASE-T Networks • Telecommunications • LAN *Colors are for representative purposes only. Actual product hues may vary. • Indoor • Commercial/Residential SPECIFICATIONS Cable Construction 24 AWG U/UTP x 4P Jacket Type CMR Compliances Conductor Material SBC Overall Temp. Rating 75° C • UL Listed Type CMR Insulation Material HDPE Voltage Rating 300 V • c(UL)us Listed • RoHS Compliant Ripcord Yes Impedence 1-350 MHz 100 ± 15 Ω • ISO/IEC 11801 Jacket Material FRPVC • TIA/EIA-568-C.2 STANDARDS COMPLIANCE c(UL)us Listed RoHS Compliant ISO/IEC 11801 TIA/EIA 568-C.2 Category 5e Cable Features AVAILABILITY • Tested to 350 MHz • Twisted Pairs to Reduce Crosstalk ITEM # AVAILABLE COLOR ITEM # AVAILABLE COLOR • Easy to Use Pull Box MBW5U-01440 Black MBW5U-03751 Orange • Footage Markers on Cable Jacket MBW5U-00932 Blue MBW5U-01554 Red • Colors: Multiple Available BULK WIRE MBW5U-01442 Gray MBW5U-01441 White MBW5U-01555 Green MBW5U-01443 Yellow CAT5e Shielded CMR Premise Cable P1 White-Blue / Blue P2 White-Orange / Orange P3 White-Green / Green P4 White-Brown / Brown Available Put-Ups ∙1000’ Pull Box Available Colors Applications • 10/100/1000BASE-T Networks • Telecommunications • LAN *Colors are for representative purposes only. Actual product hues may vary. • Indoor • Commercial/Residential SPECIFICATIONS Cable Construction 24 AWG U/UTP x 4P Ripcord Yes Compliances Conductor Material SBC Jacket Material FRPVC • UL Listed Type CMR Insulation Material HDPE Jacket Type CMR • c(UL)us Listed • RoHS Compliant Core Wrap PE Tape Overall Temp. Rating 75° C • ISO/IEC 11801 Shielding Material Aluminum Foil Voltage Rating 300 V • TIA/EIA-568-C.2 Drain Wire Diameter 0.40 mm Impedence 1-350 MHz 100 ± 15 Ω STANDARDS COMPLIANCE Features c(UL)us Listed RoHS Compliant ISO/IEC 11801 TIA/EIA 568-C.2 Category 5e Cable • Shielded to Reduce EMI • Tested to 350 MHz AVAILABILITY • Twisted Pairs to Reduce Crosstalk ITEM # AVAILABLE COLOR • Easy to Use Pull Box MBW5F-00933 Blue • Footage Markers on Cable Jacket • Color: Blue 6 www.vericomsolutions.com Category Cable CAT5e Unshielded CMX Indoor / Outdoor Premise Cable P1 White-Blue / Blue P2 White-Orange / Orange P3 White-Green / Green P4 White-Brown / Brown Available Put-Ups ∙1000’ Pull Box Applications Available Colors • 10/100/1000BASE-T Networks • Telecommunications • LAN *Colors are for representative purposes only.
Load more

Recommended publications
  • How to Choose the Right Cable Category
    How to Choose the Right Cable Category Why do I need a different category of cable? Not too long ago, when local area networks were being designed, each work area outlet typically consisted of one Category 3 circuit for voice and one Category 5e circuit for data. Category 3 cables consisted of four loosely twisted pairs of copper conductor under an overall jacket and were tested to 16 megahertz. Category 5e cables, on the other hand, had its four pairs more tightly twisted than the Category 3 and were tested up to 100 megahertz. The design allowed for voice on one circuit and data on the other. As network equipment data rates increased and more network devices were finding their way onto the network, this design quickly became obsolete. Companies wisely began installing all Category 5e circuits with often three or more circuits per work area outlet. Often, all circuits, including voice, were fed off of patch panels. This design allowed information technology managers to use any circuit as either a voice or a data circuit. Overbuilding the system upfront, though it added costs to the original project, ultimately saved money since future cable additions or cable upgrades would cost significantly more after construction than during the original construction phase. By installing all Category 5e cables, they knew their infrastructure would accommodate all their network needs for a number of years and that they would be ready for the next generation of network technology coming down the road. Though a Category 5e cable infrastructure will safely accommodate the widely used 10 and 100 megabit-per-second (Mbits/sec) Ethernet protocols, 10Base-T and 100Base-T respectively, it may not satisfy the needs of the higher performing Ethernet protocol, gigabit Ethernet (1000 Mbits/sec), also referred to as 1000Base-T.
    [Show full text]
  • HLE-1 HDMI Extender System Installation Manual
    HLE-1 HDMI Extender System Installation Manual HDBaseT IR Out HDBaseT IR Out HLE-1 TX HDMI Extender with HDBaseT-Lite™ Transmitter HLE-1 RX HDMI Extender with HDBaseT-Lite™ Power In + 24VDC Only Power Receiver HDMI IR In HDMI In HDBT Power HDMI HDMI IR In Out HDBT HLE-1 Installation Manual Table of Contents Introduction . 3 Kit Contents . 4 Feature Set . 5 Specifications . 6 Transmitter Connections . 7 Reciever Connections . 8 Transmitter Functions . 9 Receiver Functions . 10 IR Connection Diagrams . 11 Troubleshooting . 12 Warranty . 12 2 HLE-1 Installation Manual Introduction INTRODUCTION Thank you for purchasing Transformative Engineering’s HLE-1 HDMI Extender Kit. This product incorporates many advanced technologies to accomplish 1.4a HDMI compliant extension of the High Definition MultiMedia Interface protocol over one length of Category 5e/6/7 wire. Among these is certified HDBase-T technology, licensed here. This unique conversion of HDMI signals provides for the most reliable, stable and predictable method to transfer all HDMI requirements. More information on this technology may be found at the HDBase-T website, www.hdbaset.org . We are proud to be an early Adopter Member of the Alliance. Proper connection and attention to limitations of this product will provide secure, reliable, and predictable results. The most important variable to success will depend on wire chosen as the interconnection between our Transmitter and Receiver. All Category wire is not created equal. It is vital that care is taken at all times to avoid kinks, crimps, nicks, and other abuse of the wire and jacket. Also, we highly recommend that all wire be sweep tested before and after installation to insure full bandwidth is not impaired.
    [Show full text]
  • KNOW the LINGO – WHAT IS Category CABLE?
    KNOW THE LINGO – WHAT IS CategoRY CABLE? By: Joseph D. Cornwall, CTS-D Technology Evangelist—Lastar, Inc. Technical lingo is a kind of shorthand that’s used to express concepts common to that specific topic or area of study. Technical lingo is important because it provides a very precise or unique “shorthand” description of a device, effect or concept. Unfortunately, if you aren’t comfortable and familiar with the lingo of a topic it can be a tall hurdle to communicate efficiently with folks who consider the jargon of their field to be “self-explanatory.” In this series of articles we’ll lift the veils of misunderstanding from the lingo of the A/V industry. WHAT IS A CAT CABLE? The concept of Category cables was first set forth by the Electronic Industries Alliance (EIA) and is now maintained by the Telecommunications Industry Association (TIA). In 1991 the TIA/EIA-568-A standard was released (now revised to TIA/EIA-568-C) in an effort to define standards for telecommunications installations. In particular, the standard worked to define elements of balanced twisted pair cabling, fiber optic cabling and coaxial cabling, along with the associated connectors. The Cat cables discussed here are of the unshielded twisted pair (UTP) variety. You can’t be in the A/V or IT industry and not have heard of Cat5e and Cat6 cables. The Cat, as you might know, is short for “Category.” The term “Category” refers to the different levels of performance in signal bandwidth, attenuation and crosstalk associated with each cable’s design.
    [Show full text]
  • University of Technology Principles of Computer Engineering And
    University of Technology Biomedical Engineering Department First year 2nd lecture Of Principles of computer engineering and Programming methodology Asst. Lect. Amar A. Mahawish Data Communication & Computer Network Data communications refers to the transmission of data between two or more computers. A computer network is a telecommunications network that allows computers to exchange data. The physical connection between networked computing devices is established using either cable media or wireless media. The best-known computer network is the Internet. 1. Computer Network Types Generally, networks are distinguished based on their geographical span. A network can be as small as distance between your mobile phone and its Bluetooth headphone and as large as the internet itself, covering the whole geographical world. 1) Personal Area Network A Personal Area Network (PAN) is smallest network which is very personal to a user. PAN has connectivity range up to 10 meters. PAN may include wireless computer keyboard and mouse, Bluetooth enabled headphones and wireless printers. 2) Local Area Network Local Access Network (LAN) is a short-distance network. It connects computers that are close together, usually within a room or a building. Very rarely, a LAN network will span a couple of buildings. An example of a LAN network is the network in a school or an office building. A LAN network doesn’t need a router to operate. 3) Wide Area Network Wide Area Network (WAN) cover a huge geographical area. A WAN is a collection of LAN networks. LANs connect to other LANs with the help of a router to create WAN. 2. Computer Network Topologies A Network Topology is the arrangement with which computer systems or network devices are connected to each other.
    [Show full text]
  • Lanmark-6 Cable Lanmark-6 F²/UTP LSZH 500M Reel Nexans Ref.: N100.662
    Contact LAN Systems (Nexans Cabling Solutions) Phone: +44 (0)1256 486640 [email protected] LANmark-6 Cable LANmark-6 F²/UTP LSZH 500m reel Nexans ref.: N100.662 • Complies to all Category 6 cable standards • Supports Class E applications • Central cross member maintains geometry and performance • Tested up to 350MHz Description Application Nexans LANmark-6 cables are the ideal solution for most of today’s network requirements in normal office environments. They are manufactured and tested to the latest Category 6 specifications defined in the International and American cable standards and are designed to meet the quality and performance criteria needed to support all applications up to 250 MHz. • 10baseT Ethernet • 100baseTX Fast Ethernet • 1000baseTX Gigabit Ethernet • 155 MBit ATM • 622 MBit ATM • 1.2 Gbit ATM • Future class E applications Design The LANmark-6 cables have AWG 23 solid copper wires and comply with IEC 60228. The PE central cross filler helps maintain the stability of the cable geometry and Standards reduces the risk of a reduction in performance when bending the cable. The cables are available with a Dark Grey PVC or an Orange LSZH sheath. Both International EN 50288; versions have flame retardant properties compliant with IEC 60332-1. IEC 61156-5; ISO/IEC 11801 National ANSI/TIA-568-C.2 Performance Tested to 350 MHz and with guaranteed performance to 250 MHz, Nexans LANmark-6 cables exceed the requirements of the International, European and American cable standards, including ISO/IEC 11801:2002, IEC 61156-5, EN 50173, EN 50288 and TIA/EIA 568-C.2.
    [Show full text]
  • CATEGORY 5E/6 FLAT UTP PATCH CORDS
    ETHERNET CABLES NCB-5EUORGF1-5 NCB-C6UBLUF1-5 CATEGORY 5e/6 FLAT UTP PATCH CORDS ETHERNET CONNECTIVITY HIGH-SPEED PERFORMANCE ULTRA-PORTABLE Ideal for use with 10, 100Base-TX or Supports speeds of up to 1000 Mbps across distances of up Easy and flexible setup 1000Base-T networks to 100 feet RELIABLE CABLES FOR YOUR NETWORK D-Link Category 5e and Category 6 Ethernet cables are superior for transmitting data over local area networks (LANs). These CAT5e/CAT6 cables exceed performance requirements specified by the TIA/EIA-568B.2 and IEC 60603-7-4 standards (Category 5e Class D). The CAT5e/6 cables are made using four Unshielded Twisted Pairs (UTP) of 100 ohm impedance and are protected by a plastic outer jacket. CATEGORY 5e CABLE The Category 5e cable, an enhanced version of Category 5, adheres to more stringent standards specified by TIA/EIA-568B.2 and IEC 60603-7-4. These cables are made using 32 gauge (AWG) copper wires with about three twists per inch enabling them to transmit data at 1000 Mbps (~1 Gigabit per second) with a frequency of 100 MHz. The CAT5e cables are suitable for 10BASE-T and 100BASE-TX Fast Ethernet. CATEGORY 6 CABLE The Category 6 cable is backward compatible with Category 5/5e and Category 3 specifications. Compared to its predecessors, CAT6 cables reduce crosstalk and system noise. The superior insulation around the 32 gauge (AWG) copper wires attribute to its increased performance. The CAT6 cables can transmit data at 1000 Mbps (~1 Gigabit per second) with a frequency of 600 MHz.
    [Show full text]
  • CAT 6 Solutions Guide
    Copper Systems CAT 6 Solutions Copper Systems CAT 6 Solutions Introduction Vericom® Copper Systems Vericom’s Copper Systems are designed to provide the highest level of performance possible at the best value. For your convenience, we offer two separate alternatives to suit your specific application. VGS™ (Vericom Global Solutions) Our full project solutions line, designed with the future of your business in mind. This line has been tested and certified to meet or exceed the most current industry standards and is guaranteed to stand the test of time. VGC™ (Vericom Global Commodity) Our global commodity line provides an economical price savvy solution, designed, tested and certified to suit current light commercial or residential applications. Category 6 Solutions Our VGS6™ Category 6 Cable supports 10GBASE-T Ethernet based on limited distances per the standard, 1000BASE-T (Gigabit Ethernet), Brand Values & Philosophy 100BASE-T (Fast Ethernet), 155 Mb/s ATM, 622 Mb/s ATM, 1.2 Gb/s ATM, Digital video and We strive every day to make Vericom the world’s most desirable network infrastructure and connectivity broadband/baseband analog video, Voice over solutions provider to work for and partner with. Internet Protocol (VoIP). Category 6 is backwards Our desire to be the best in our field by offering compatible with Category 5e systems as well as quality products with integrity is a driving force to IEEE 802.3af/802.3at (48 cables in a bundle) and provide our customers with product offerings that 802.3bt type 3 and type 4 (24 cables in a bundle) remain relevant throughout the ever-changing data technologies and communications community.
    [Show full text]
  • TX6™ Category 6 U/UTP Copper Cable – North America Additional Specifications
    TX6™ Category 6 U/UTP Copper Cable – North America SPECIFICATION SHEET specifications Category 6 U/UTP Copper Cable Category 6 cable shall meet ANSI/TIA-568-C.2 Category 6 Plenum: PUP6C04**-ULP component standard. The conductors shall be 23 AWG construction with FEP/polyolefin insulation. The copper Cable Prep Tools conductors shall be twisted in pairs and covered by a low Wire snipping smoke, flame-retardant (CMP) PVC jacket. tool: CWST Wire stripping technical information tool: CJAST Electrical performance: **For standard cable colors, add suffix Certified channel performance in a 4-connector configuration up BU(Blue), WH (White), RD (Red), OR to 100 meters and meets ANSI/TIA-568-C.2 Category 6 (Orange),YL (Yellow), GR (Green), VL (Violet), standard at swept frequencies up to 250MHz IG(International Gray), or BL (Black). Cable available in a standard pallet configuration of Certified component performance up to 100 meters and meets 36 cartons per pallet. the component requirements of ANSI/TIA-568-C.2 Category 6 For other colors or pallet configurations, component standard at swept frequencies up to 250 MHz contact customer service. Standards compliance: UL Listed CMP-LP (0.5A) for Plenum Visit www.panduit.com for connectivity components. Conductors/insulators: Plenum – 23 AWG solid copper covered by FEP/polyolefin insulation Insulation diameter: .033 in. - .043 in. Flame rating: Plenum – NFPA 262 PoE compliance: Meets IEEE 802.3af, IEEE 802.3at and IEEE 802.3bt for PoE applications Installation tension: 25 lbf (110N) maximum Temperature rating: 32°F to 122°F (0°C to 50°C) during installation -4°F to 194°F (-20°C to 90°C) during operation (Plenum) Cable jacket: Plenum – low smoke, flame-retardant PVC Cable diameter: Plenum – 0.205 in.
    [Show full text]
  • UTP OUTDOOR with MESSENGER CATEGORY 6+ (600 Mhz)
    UTP OUTDOOR WITH MESSENGER CATEGORY 6+ (600 Mhz) BISMON Category6 4 Pair UTP OUTDOOR with Messenger Wire and Double Jacket 23AWG solid bare copper, Cable provides significant headroom above all TIA/EIA and ISO/IEC category 6/class E transmission performance specifications.comb ne our high performance category 6 connectivity with Category 6 cable and use for backbone ethernet lan gigabit network. It is designed for use in horizontal cabling situations and supplied in 305m (1,000ft) easy pull out reels. These category 6 systems exceed ANSI/TIA/EIA-568-B.2-1 Category 6 performance requirements, providing usable banwidth well beyond 600 Mhz. Applications Benefit 4Mbps Token Ring (IEEE 802.5) Provides cost effective solution 10Mbps 10Base-T Ethernet (IEEE 802.3u) Provides remaining length of cable on reel 16Mbps Token Ring (IEEE 802.5) Performance assurance for multiple high-bandwidth applica- 100Mbps Fast Ethernet (IEEE 802.3u, ANSI X3T9.5 TPDDI) tions (e.g., Fast Ethernet, ATM, Gigabit Ethernet) 100 VG ANYLAN (IEEE 802.12) Reduces tension on wire to ensure proper electrical 155 Mbps ATM performance after installation 622Mbps ATM Easily identifiable conductor mate 1000Mbps 1000Base-T Gigabit Ethernet (IEEE 802.3) Eliminates guess work of footage in box or reel 1 Broadband Video and voice, ISDN Offers flexibility in selection of connectivity solution Voice over internet Protocal (VoIP) Easily identifiable jacket color Power over Ethernet (PoE) - IEEE 802.3af, IEEE 802.3at Use Full high speed for IP Camera Standards Compliance Features 3P Third Party Testing 2nd:2002 Verified, ETL,TIA/EIA- - Complies with Category 6 cables exceed standards : 568A/B/C.2 Category 6, ISO/IEC-11801 2002 (Edition 2) Class ISO/IEC 11801 Class E, ANSI/TIA/EIA 568-B.2-1 E, CENELEC EN50173: 2002 (Edition 2), EN50288-3-1, ICEA Supports transmission of digital and analogue voice, data and S-102-700,EN 50173-1, ASTM D4566-98, IEC61156-5(2002), video signal.
    [Show full text]
  • Ethernet Twisted Pair Cable Categories
    Cabling Ethernet Twisted Pair Cable Categories. LPTPCATX_AN_ENB01W This Application Note explains the differences between twisted pair categories used for Structured Cabling. A Category 5 cable. Category 5 (CAT 5) cable is a multi-pair (usually 4 pair) high performance cable that consists of twisted pair conductors, used mainly for data transmission. Basic CAT 5 cable was designed for characteristics of up to 100 MHz. CAT 5 cable is typically used for LAN Ethernet networks running at 10 or 100 Mbps. Unshielded Twisted Pair (UTP) construction makes the cable highly cost-effective for data networks. B Category 5e Cable. Category 5e (CAT 5e) cable, also known as Enhanced Category 5, is designed to support full-duplex Fast Ethernet operation and Gigabit Ethernet. The main differences between CAT 5 and CAT 5e can be found in the specifications. The performance requirements have been raised slightly in the new standard. CAT 5e has stricter specifications for Power Sum Equal-Level Far-End Crosstalk (PS-ELFEXT), Near-End Crosstalk (NEXT), attenuation, and Return Loss (RL) than those for CAT 5. Like CAT 5, CAT 5e is a 100 MHz standard, but it has the capacity to handle bandwidth superior to that of CAT 5. C Category 6 Cable Category 6 (CAT 6) cable provides higher performance than CAT 5e and features more stringent specifications for crosstalk and system noise. The quality of the data transmission depends upon the performance of the components of the channel. To transmit according to CAT 6 specifications, jacks, patch cables, patch panels, cross-connects, and cabling must all meet CAT 6 standards.
    [Show full text]
  • Wheatstone Corporation Technical Documentation
    Wheatstone Corporation Technical Documentation The Role of Wiring Integrity on WheatNet-IP Network Reliability A Review of Gigabit Ethernet Network Cabling Requirements and Common Installation Practices 600 Industrial Drive New Bern, NC 28562 252.638.7000 www.wheatstone.com Paul Picard – January 2010 v 1.0 Introduction Whether you are building a brand new gigabit network for audio transport, expanding a simple fast Ethernet network, or just making some patch cables for your current network the same general rules apply. By building and maintaining your network the “right way” you ensure the long term reliability of this fundamental but critical part of your IP based audio distribution system. This document will explain the process of selecting the components and building the cabling infrastructure that will be the backbone of your high speed audio data network. Network Speed Any discussion of building a wiring plant for an audio over IP system should start with a clear understanding of what will be connected to the system now and in the foreseeable future. The WheatNet IP Blade hardware was designed to utilize the 1000 Base T Gigabit Ethernet standard exclusively as the transport mechanism for all audio i/o and mix engine traffic. Certain mixing and routing control devices as well as general purpose PC’s on the network continue to use Fast Ethernet 100BASE–TX connectivity. With this in mind, the wiring plant we will discuss must support gigabit connectivity from end to end. Ethernet Wiring Standards While it is true that you could install a basic Ethernet network without knowing anything about standards – short of the RJ45 wiring scheme – installers of Ethernet networks for professional use in commercial spaces which are subject to official inspector review will find the standards information invaluable.
    [Show full text]
  • TX6™ Category 6 U/UTP Copper Cable
    TX6™ Category 6 U/UTP Copper Cable SPECIFICATION SHEET specifications Category 6 cable shall meet ANSI/TIA-568-C.2 Category 6 U/UTP Copper Cable Category 6 component standard. The conductors shall Plenum: PUP6C04*-U be 23 AWG construction with FEP/polyolefin (CMP) or Riser: PUR6C04*-U polyolefin (CMR) insulation. The copper conductors shall be twisted in pairs and covered by a low smoke, flame- Cable Prep Tools retardant (CMP) PVC jacket or a flame-retardant (CMR) Wire snipping PVC jacket. tool: CWST Wire stripping tool: CJAST technical information Electrical performance: Certified channel performance in a 4-connector configuration up to *For standard cable colors, add suffix BU (Blue), WH (White), RD (Red), OR (Orange), 100 meters and meets ANSI/TIA-568-C.2 Category 6 YL (Yellow), GR (Green), VL (Violet), IG standard at swept frequencies up to 250MHz (International Gray), or BL (Black). Cable avail- able in a standard pallet configuration of 36 car- Certified component performance up to 100 meters and meets the tons per pallet. component requirements of ANSI/TIA-568-C.2 Category 6 component For other colors or pallet configurations, contact customer service. standard at swept frequencies up to 250 MHz Visit www.panduit.com for connectivity Conductors/insulators: Plenum – 23 AWG solid copper covered by FEP/polyolefin insulation components. Riser – 23 AWG solid copper covered by polyolefin insulation Flame rating: Plenum – NFPA 262 Riser – UL1666 PoE compliance: Meets IEEE 802.3af and IEEE 802.3at for PoE applications Installation tension: 25 lbf (110N) maximum Temperature rating: 32°F to 122°F (0°C to 50°C) during installation -4°F to 167°F (-20°C to 75°C) during operation (Riser) -4°F to 167°F (-20°C to 75°C) during operation (Plenum) Cable jacket: Plenum – low smoke, flame-retardant PVC Riser – flame-retardant PVC Cable diameter: Plenum – 0.224 in.
    [Show full text]