3M™ Simply Interactive System, Version 2 English

3M™ Simply Interactive English System, Version 2 Product No. 78-6972-0051-3 For use with the 3M™ Super Close Projection Systems SCP716/ SCP725/SCP716W/SCP725W Installation and Use Instructions

April 2011 78-6971-1595-0-B

Book.indb 1 9/16/11 3:44 PM 3M™ Simply Interactive System, Version 2 English

Book.indb 2 9/16/11 3:44 PM 3M™ Simply Interactive System Contents English Safety Information...... 4 Introduction ...... 5 Package Contents...... 6 Installing the 3M Simply Interactive System ...... 7 Installing the 3M Simply Interactive Camera...... 8 Installing the Pen Batteries ...... 11 Installing the Software for Computers Running Microsoft® Windows® ...... 12 Installing the Software for Computers Running Mac OS® X ...... 14 Installing the Software for Computers Running Linux® Operating System...... 15 Operating the 3M™ Simply Interactive System...... 17 Troubleshooting ...... 19 Product Speciﬁcations...... 20 Warranty; Limited Remedy; Limited Liability...... 21 Notices ...... 23

Book.indb 3 9/16/11 3:44 PM 3M™ Simply Interactive System, Version 2 Safety Information Please read, understand, and follow all safety information contained in these instructions prior to the

English use of this product. Retain these instructions for future reference. Intended Use The 3M™ Simply Interactive System, Version 2 (SIv2) is designed and tested for use with the 3M SCP Wall Mounts and SCP716/SCP725/SCP716W/SCP725W Projectors. 3M has not tested this product with other projectors or mounts. This product is not intended for the home market.

Explanation of Signal Word Consequences m Warning: Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury and/or property damage. m Caution: Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury and/or property damage. c Warning: Hazardous voltage.

m Warning To reduce the risks associated with choking: t Keep the 3M Simply Interactive pen and its small parts away from children under three years of age.

m Caution To reduce the risks associated with environmental contamination: t Dispose of components in accordance with applicable federal, state and local regulations. To reduce the risks associated with battery hazards: t Use only type AAA alkaline batteries. t Avoid ﬁre and heat sources. t Do not attempt to recharge batteries. t Do not break or disassemble batteries. t Avoid eye and skin contact with battery chemicals. t Avoid ingesting and inhaling battery chemicals. t Remove battery when not used for an extended period of time SAVE THESE INSTRUCTIONS

Book.indb 4 9/16/11 3:44 PM 3M™ Simply Interactive System, Version 2 Introduction English THANK YOU FOR CHOOSING 3M This product has been produced in accordance with 3M’s quality and safety standards to provide smooth and trouble free use in the years to come. For optimum performance, please follow the operating instructions carefully. We hope you will enjoy using this high performance product in your classroom, meetings, presentations, and training sessions. PRODUCT FEATURES The 3M Simply Interactive System when combined with a 3M SCP716/SCP725/SCP716W/ SCP725W projector and ﬁxed or folding wall mount, will transform a whiteboard or similar smooth wall surface into an interactive computer display. Simply touch the stylus pen to the whiteboard surface to control computer mouse functions. You can also use annotation software available from third party vendors to annotate projected images. The 3M Simply Interactive System works with computers running Microsoft® Windows®, Mac OS® X or Linux®. The key features are: t Easy to install and use t Compatible with computers running Microsoft® Windows®, Mac OS® X or Linux® t Run application from the USB ﬂash memory drive or optionally install onto the computer hard drive t Application will auto-run (computers running Microsoft® Windows® only) when computer is connected to system t Set and forget, no mechanical adjustments required after initial installation t Intended for whiteboard surfaces, may work on other wall surfaces

Book.indb 5 9/16/11 3:44 PM 3M™ Simply Interactive System, Version 2 Package Contents 1 Camera

English 2 Mounting Screw 3 3M Simply Interactive Pen

4 2x AAA Type Batteries 2 5 4.5 m (14.8 ft) USB Cable 1

4.5 m (14.8 ft)

Book.indb 6 9/16/11 3:44 PM 3M™ Simply Interactive System, Version 2 Installing the 3M Simply Interactive System English Pre-Installation The 3M Simply Interactive System comes with the hardware necessary to install onto a 3M™ SCP716/SCP725/SCP716W/SCP725W projector. Additionally, the system comes with software that is compatible with a computer running Microsoft® Windows®, Mac OS® X or Linux®. The hardware is a camera and pen tool. The software application receives the location of the pen from the USB camera to emulate a mouse interface or touch interface action. For best performance, please consider these items before you install the 3M Simply Interactive System: t Screen Surface: The pen requires a smooth and hard writing surface (whiteboard is recommended) to prevent damage to the pen tip or the screen surface. Note: Painted wood, wallpaper, sheetrock, cement or chalkboard surfaces are not recommended because they are typically too soft (pen will dent and scratch surface) or too coarse (rough surface will damage pen tip). t IR Interference: The 3M Simply Interactive System works in most ofﬁce and school lighting conditions except where infra-red (IR) light is present. The 3M Simply Interactive System uses IR for detecting the pen location. Other IR light sources can cause interference with the system. Some IR light sources are direct or indirect sunlight, IR remote controls, and IR Microphones. The illustration below shows the viewable area that is seen by the camera. To reduce the chance of IR interference, remove all direct and reﬂected IR light sources from this area.

2.5' (0.76 m)

5' 5' (1.5 m) (1.5 m)

2' (0.6 m)

Book.indb 7 9/16/11 3:44 PM 3M™ Simply Interactive System, Version 2 Installing the 3M Simply Interactive Camera The 3M Simply Interactive camera is installed directly onto the projector. It is not necessary to

English remove the projector from the 3M wall mount.

Important Note: If a ladder is needed during installation, read and understand all safety instructions printed on the ladder or its documentation.

Tools Required Philips screwdriver Attach the Camera to the Projector 1 Remove the indicated screw below the lens from the bottom of the projector.

2 Projector models SCP716W and SCP725W only: Remove the two screws shown, then remove the spacer from the camera housing and discard it.

3 Attach the camera to the projector as shown. The top of the camera bracket snaps into position behind the lens.

Book.indb 8 9/16/11 3:44 PM 3M™ Simply Interactive System, Version 2 4 Secure the camera to the projector with the provided mounting screw. English

Installing the USB Cable with the Folding Wall Mount Installation Tip: If a USB cable is already connected to the projector and you do not use the remote control’s mouse feature, you can switch the USB cable from the projector and to the Simply Interactive camera and skip the “Installing USB Cable...” section.

1 Remove the wall mount cover by removing the 3 screws.

Installing the USB Cable with the Fixed Wall Mount 1 Remove the wall mount from the wall.

Book.indb 9 9/16/11 3:44 PM 3M™ Simply Interactive System, Version 2 Routing and Securing the USB Cables 1 Route the 4.5 m (14.8 ft) USB cable through

English the wall mount arm.

2 Replace the folding wall mount cover or reinstall the ﬁxed mount. 3 Plug the USB cable into the port on the side of the camera. 4 Plug the other end of the USB cable into the 3M™ I/O Module SCPI/OV2 or your computer. The following diagram shows the USB cable connections.

Book.indb 10 9/16/11 3:45 PM 3M™ Simply Interactive System, Version 2 Installing the Pen Batteries English The 3M Simply Interactive Pen requires two new AAA-type batteries. 1 Remove the battery cap by turning it counter-clockwise. 2 Insert the battery negative post (–) ﬁrst into the pen. 3 Replace the battery cap by turning it clockwise.

Turn the pen on and off using the switch at the end.

Book.indb 11 9/16/11 3:45 PM 3M™ Simply Interactive System, Version 2 Installing the Software for Computers Running Microsoft® Windows® English Computer Requirements Description Requirement Computer and Processor 500 MHz or Faster Hard Disk 500 KB Available Disk Space Operating System Windows XP (SP2) (32-bit), Windows 7, Windows Vista Requirement Support Software Microsoft .NET Frameworks 2.0 or above

Run 3M Simply Interactive from USB Flash Drive Once you attach the 3M Simply Interactive camera to your computer, you can run the Simply Interactive System from the camera’s built-in USB drive without installing the software on your computer: 1 Open the camera’s built-in USB drive by opening Windows Explorer and then open the drive labeled 3M SI V2.

Note: In some case, the Autoplay window opens after the USB cable from the camera is connected to the computer. Click “Open folder to view ﬁ les” from the autoplay list and continue to step 2.

2 Run Launcher.exe. 3 The 3M Simply Interactive software will execute and an icon will appear in the system tray beside the system clock.

GREEN icon = camera is connected Red icon = camera not connected

4 Calibrate the system. See “Calibration” on page 18.

Book.indb 12 9/16/11 3:45 PM 3M™ Simply Interactive System, Version 2 Download and Install 3M Simply Interactive onto Your Computer You can install the 3M Simply Interactive software onto your computer after downloading it from the English camera’s built-in USB Drive or the 3M website.

Download from camera’s built-in USB Drive and install 1 Open the camera’s built-in USB drive in Windows Explorer and open the drive labeled 3M SI V2. 2 Open the Windows folder. 3 Double-click setup.exe and follow the install wizard instructions to install the 3M Simply Interactive software onto your computer.

Download from 3M website and install 1 Go to the 3M website: www.mmm.com/meetings. 2Click Product Software and select Simply Interactive. 3 Click the link to download the 3M Simply Interactive Version 2 software 4 After download is complete, launch the setup ﬁle and follow the install wizard instructions to install the 3M Simply Interactive software onto your computer.

Book.indb 13 9/16/11 3:45 PM 3M™ Simply Interactive System, Version 2 Installing the Software for Computers Running Mac OS® X English Computer Requirements Description Requirement Hard Disk 10 MB Available Disk Space Operating System Mac OS X 10.4.11, 10.5 or above, except 5.6

Download and Install 3M Simply Interactive Onto Your Computer You can install the 3M Simply Interactive software onto your computer after downloading it from the camera’s built-in USB Drive or the 3M website.

Download from camera’s built-in USB Drive and install 1 Open the camera’s built-in USB drive by opening Finder and opening the drive labeled 3M SI V2 2Copy mac.zip to the computer’s desktop. 3Open mac.zip and SI for Mac will appear on the computer’s desktop. 4Move SI for Mac to the Applications folder on your hard drive.

Download from 3M website and install 1 Go to the 3M website: www.mmm.com/meetings 2Click Product Software and select Simply Interactive 3 Click the link to download the 3M Simply Interactive software 4Copy mac.zip to the computer’s desktop. 5Open mac.zip and SI for Mac will appear on the computer’s desktop. 6Move SI for Mac to the Applications folder on your hard drive.

Book.indb 14 9/16/11 3:45 PM 3M™ Simply Interactive System, Version 2 Installing the Software for Computers Running Linux® Operating System English Linux is a free and open source software system that is released under the GNU General Public License version 2 (GPLv2). There are many different Linux distributions that have been released based upon the Linux kernel. 3M has only tested the compatibility of the 3M Simply Interactive application with the Ubuntu and SUSE distributions. Computer and OS Requirements Item Ubuntu SUSE OS Version 10.04 11.3 PC requirement 32-bit 32-bit Library gtk+-2.0 run time, X11 runtime, gtk+-2.0 run time, X11 runtime, libxﬁxes run time libxﬁxes run time 2 Note: The 3M Simply Interactive software is a 32-bit application. To run this application from a 64-bit machine, it is necessary to install the 32-bit (ia32) software libraries found in the Linux 64-bit software package.

The 3M Simply Interactive software application provides you the following installation options: Installing the Software for Computers Running Ubuntu Note: You must login as root user to install the Simply Interactive software.

1 Plug the USB cable from the Simply Interactive into your computer and the 3M SI VS disk will appear on the desktop. 2 Open the 3M SI V2 disk 3 Open the linux folder 4 Run 1-setup.exe to install Simply Interactive. Installing the Software for Computers Running SUSE Note: You must login as root user to install the Simply Interactive software.

Book.indb 15 9/16/11 3:45 PM 3M™ Simply Interactive System, Version 2 Troubleshooting Notes for openSUSE If you receive an error because there is no application installed that can open the ﬁle 1-Setup, the 1-Setup permissions needs to be updated. Here is a how to change the permissions for 1-Setup: English 1 Copy and paste the Linux folder onto your local drive. (The 3M SI V2 disk is read-only and will not allow you to change the permission.) 2Right-click 1-setup to open the contextual menu. 3Click Properties from the contextual menu. 4 Click the Permissions tab. 5 Conﬁrm that Is executable is checked.

Book.indb 16 9/16/11 3:45 PM 3M™ Simply Interactive System, Version 2 Operating the 3M™ Simply Interactive System English The 3M Simply Interactive Menu 1 From the system tray (Windows), menu bar (Mac) or menu bar (Linux), click the Simply Interactive icon to launch the software.

Windows® Mac OS® X Linux® (Ubuntu) Linux® (SUSE)

Green icon = camera is connected Red icon = camera not connected

2 Select the desired menu option from the Simply Interactive menu, shown below, to launch that option.

Menu Option Description Help Open the online help Sensitivity Set the sensitivity of the pen to low, medium or high Language Set the display language for SI menus Calibration Start calibration About View system information for the SI application Exit Exit the SI application

Sensitivity The Pen Sensitivity setting controls the sensitivity of the camera to the pen. When the setting is increased, the camera requires less light from the pen while becoming more sensitive to other light sources. When the setting is decreased, the camera requires more light from the pen and can ﬁ lter out some light sources. 1 Select the Sensitivity option to display the pen sensitivity adjustment window. 2Click Low, Medium or High to set the sensitivity of the SI pen for best performance.

Book.indb 17 9/16/11 3:45 PM 3M™ Simply Interactive System, Version 2 Calibration The 3M Simply Interactive pen must be calibrated each time you start up the SI application. This option calibrates the pen movement to accurately reﬂect the computer mouse pointer. English 1 Select the Calibration option from the SI menu. 2 Tap the center of each calibration target with the 3M Simply Interactive Pen.

3 The computer screen will return after the calibration is complete.

Note: Press Esc (Windows only) to exit the calibration screen before calibration is complete.

Using the Simply Interactive Pen The 3M Simply Interactive Pen can perform most computer mouse functions like left and right mouse click and click and drag. In order for the pen to work properly, the projected computer image must be projected onto a rigid surface as mentioned in “Pre-Installation” on page 7.

Performing a Left Mouse Click with Pen Perform a left mouse click by tapping the image with the pen. For example, select an icon on the projected computer image by tapping it once with the pen.

Performing a Double Click with Pen Perform a double click by quickly tapping the image twice with the pen.

Performing a Right Mouse Click with Pen Perform a right click by pressing and holding the pen tip on the image and the right mouse click function will be executed.

Performing Click and Drag with Pen The click and drag function is used for selecting multiple items on the screen, drawing a line, or drag-and-drop items from one application to another. Perform a click and drag by pressing and holding the pen tip on the image and then move the pen to the desired location on the image.

Book.indb 18 9/16/11 3:45 PM 3M™ Simply Interactive System, Version 2 Troubleshooting English The USB flash drive is not available on my computer in Windows Explorer. t You can assign the USB flash drive to a drive letter not already used by another USB drive or network drive. Please refer to KB297694 on the Microsoft Support Website. The computer mouse pointer moves without using the 3M Simply Interactive pen or the computer’s mouse. t You can check for interference from sunlight reflections off of shiny or mirrored surfaces, Sometime the reflection is not visible from the audience’s viewpoint of the whiteboard surface. The camera may see reflections that the audience cannot see. t You can check for interference from infrared remote controls, infrared microphones or other IR devices. The computer mouse pointer will not move. t You can detach the 3M Simply Interactive System from the computer. This will confirm the 3M Simply Interactive System is the cause. t You can check for interference from sunlight reflections off of shiny or mirrored surfaces, Sometime the reflection is not visible from the audience’s viewpoint of the whiteboard surface. The camera may see reflections that the audience cannot see. t Remove all sunlight from the view of the camera. When writing with the pen, the marks are not continuous lines. t Change the Pen Sensitivity level. Try setting the pen sensitivity level to High. t Replace the batteries in the pen.

Book.indb 19 9/16/11 3:45 PM 3M™ Simply Interactive System, Version 2 Product Speciﬁcations Camera English Description Speciﬁcation Detection Technology Infrared Camera Throw Ratio 0.54 Electrical Interface USB-B port (USB 1.1/2.0) Power Consumption <500 mW Regulatory FCC Class B, CISPR Class B

Pen Description Speciﬁcation Light Output Infrared Power Requirement 2x AAA alkaline batteries

Software Application Requirements Description Requirement Operating System Microsoft® Windows XP, Windows Vista, and Windows 7 Mac OS® X 10.4.11, 10.5 or above, except 5.6 Linux® (Ubuntu 10.04, Suse 11.3), 32 Bit Processor Type Intel® Pentium® or above or equivalent Minimum Memory 512 MB RAM Minimum Hard Drive Space 30 MB Windows, 10 MB Mac, 1 MB Hardware Available USB 1.1 or 2.0 port

Book.indb 20 9/16/11 3:45 PM 3M™ Simply Interactive System, Version 2 Warranty; Limited Remedy; Limited Liability English This warranty applies to the continental US only. The warranty terms, conditions, remedy and limitation may vary in other countries. Contact your local 3M Company for warranty information. The 3M Simply Interactive is warranted to be free from defects in material or manufacture for a period of one (1) year from the date of purchase. THE WARRANTIES STATED ABOVE ARE EXCLUSIVE AND ARE MADE IN PLACE OF ANY AND ALL WARRANTIES, EXPRESS OR IMPLIED WARRANTIES OR CONDITIONS, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR ANY INDUSTRY PRACTICE OR CUSTOM OR TRADE USAGE. In the event the 3M Product fails to conform to the above stated warranties within the applicable warranty period, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M Product or to refund the purchase price of the 3M Product. All replaced parts or products become property of 3M. If the product is repaired, 3M will repair the defective part(s) with a new or used part(s). If the 3M Product is replaced, 3M will replace the 3M Product with the same or equivalent model and with a new or refurbished 3M Product. In the case of an approved warranty claim, the replacement 3M Product will carry only the remaining term of the original 3M Product’s warranty period as stated above. For warranty service, you must provide proof of the date of the original purchase else the manufacturing code date will be used to establish the start date of the warranty. The following are exclusions to the above listed warranty: a This warranty does not cover 3M Product that is modified or damaged through improper storage, misuse, abuse, accident, vandalism, improper installation, neglect, improper shipping, damage caused by acts of war, disasters such as fire, flood, and lightning, improper electrical current, software problems, interaction with non-3M products, or service other than by a 3M Authorized Service Provider, neglect or mishandling by any person. Normal wear and tear is not covered under warranty. b 3M Product is designed to operate in the typical indoor environment. This warranty does not cover 3M Product used outside of the following circumstances: t 100V-240V AC, 50/60 Hz t Office (or similar) environments with low levels of smoke or air born particulates. Altitude Temperature Humidity 0–6000 ft (normal fan speed) 5°C–35°C (41°F–95°F) 25% to 80% t Storage conditions: -20°C to 60°C, maximum 40,000 ft. c This warranty does not cover any additional costs including, but not limited to, those associated with removal, cleaning or installation of the 3M Product, adjustments, (mechanical or electronic) made to the 3M Product or replacing customer replaceable parts like lamps and air filters. d This warranty covers only normal use of the product. 24-hour-per-day or other excessive continual use causes strain and is not considered normal use. e This warranty does not cover consumables (e.g., fuses), other than lamps and only as set forth below. © 2011 3M. All Rights Reserved. 21

Book.indb 21 9/16/11 3:45 PM 3M™ Simply Interactive System, Version 2 f This warranty is not transferable. g 3M is not responsible for warranty service should the 3M label or logo or the rating label or serial number be removed unless otherwise stated in writing for the purpose of private labeling English for partnership requirements. h This warranty does not cover postage, insurance, or shipping costs incurred in presenting your 3M Product for warranty service. Said costs are the customer’s responsibility. If a claimed defect cannot be identified or reproduced in service, the customer may be held responsible for cost incurred. Should your warranty upgrade include a “change out” service and the claimed defect cannot be identified or reproduced by the technician, the customer will be responsible for call out costs. FAILURE TO FOLLOW THE INSTRUCTIONS CONTAINED IN THE APPROPRIATE 3M PRODUCT MANUAL OR FAILURE TO USE THE 3M PRODUCT IN ACCORDANCE WITH 3M’S INTENDED USE STATEMENT, WILL VOID ALL WARRANTIES AND LIMITED REMEDIES. EXCEPT AS SPECIFICALLY STATED IN THE APPLICABLE 3M PRODUCT MANUAL, 3M SHALL NOT BE LIABLE FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS, REVENUE OR BUSINESS) RESULTING FROM, OR IN ANY WAY RELATED TO PERFORMANCE, USE OR INABILITY TO USE ANY OF THE 3M PRODUCT. This limitation applies regardless of the legal theory upon which damages are sought. For warranty support, please call or write your local 3M office or a 3M Authorized Service Provider to obtain RMA # (Return Material Authorization Number) before returning the product. If you are inside the Continental United States of America, please contact 3M Customer Service at 1-800-328-1371 or email [email protected]. What 3M Will Do To Correct Problems t If your 3M Product requires service, 3M will ask you to bring or send the 3M Product, securely packaged in its original container or equivalent, along with proof of the date of original purchase, to your 3M Service Dealer or 3M Service Center. t 3M will, at its option, repair or replace the defective unit without charge for parts or labor. Return of the 3M Product will be at 3M’s expense. t When warranty service involves the exchange of the 3M Product or of a part, the item replaced becomes 3M property. t The exchanged 3M Product or part may be new or previously refurbished to the 3M standard of quality, and at 3M’s option, the replacement may be another model of like kind and quality. t 3M’s liability for replacement of the warranted 3M Product or part will not exceed the original retail selling price of the 3M Product. Exchange or replacement products or parts assume the remaining warranty period of the product covered by this limited warranty. Trademarks and Copyrights The 3M logo and 3M are trademarks of 3M Company. All other trademarks or registered trademarks are property of their respective companies.

Book.indb 22 9/16/11 3:45 PM 3M™ Simply Interactive System, Version 2 Notices English Important Notice All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly set forth in a written agreement signed by an authorized officer of 3M. Regulatory Notices FCC STATEMENT - CLASS A This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Instructions to Users: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide a reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Notice: This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le materiel brouilleur du Canada. Instructions to Users: This equipment complies with the requirements of FCC equipment provided that the following conditions are met. The cables may have to be used with the core set to the projector side. Use the cables which are included with the projector or specified. Note: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. CE Statement Electromagnetic Compatibility Statement: Meets 2004/108/EC Directive WEEE STATEMENT: The following information is only for EU-members States: The mark shown to the right is in compliance with Waste Electrical and Electronic Equipment Directive 2002/96/EC (WEEE). The mark indicates the requirement NOT to dispose the equipment as unsorted municipal waste, but use the return and collection systems according to local law.

Book.indb 23 9/16/11 3:45 PM 3M™ Simply Interactive System, Version 2 RoHS STATEMENT: 3M Projection Systems can provide RoHS certiﬁcation for products meeting the RoHS directive.1 European (EU) Restriction of Hazardous Substances (RoHS) Directive, 2002/95/EC. 1RoHS compliant means that the product or part does not contain any of the substances in excess English of the following maximum concentration values in any homogeneous material, unless the substance is in an application that is exempt under RoHS, as amended:(a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. This information represents 3M’s knowledge and belief, which may be based on information provided by third party suppliers to 3M.

Book.indb 24 9/16/11 3:45 PM 3M is a trademark of 3M Company. Linux® is the registered trademark of Linus Torvalds in the U.S. and other countries. All other trademarks or registered trademarks are property of their respective companies. 1 Projection Systems 3M Austin Center 6801 River Place Blvd. 3M Mexico, 3M Europe 3M Canada Austin, TX 78726-9000 S.a. de C.V. Boulevard de l'Oise P.O. Box 5757 800-328-1371 Apartado Postal 14-139 95006 Cerge Pontoise London, Ontario www.3M.com/meetings Mexico, D.F. 07000 Cedex N6A 4TI [email protected] Mexico France Please Recycle. Printed in USA. © 3M 2011. All Rights Reserved. 78-6971-1595-0-B

Book.indb 25 9/16/11 3:45 PM