Sodium Aluminate 38 Specification USALCO

Total Page：16

File Type：pdf, Size：1020Kb

Sodium Aluminate 38 Specification USALCO

Technical Data Sheet USALCO 38 Sodium Aluminate Solution, 38% Solids USALCO 38 is an economical source of highly reactive alumina manufactured by dissolving alumina tri-hydrate (ATH) into sodium hydroxide and water. USALCO 38 is also stabilized to prevent alumina from precipitating. The use of only stringently selected raw materials and state- of-the-art manufacturing practices ensure that USALCO 38 is of the highest quality. USALCO 38 meets the specifications of the American Water Works Association Standard B405-00 and complies with the requirements of NSF/ANSI Standard 60: Drinking Water Treatment Chemicals – Health Effects at a maximum dosage of 105 mg/L. PROPERTIES SAFETY / HANDLING Chemical Formula: Na2Al2O4 Observe caution when handling Appearance: Amber Liquid corrosive materials. Please consult Specific Gravity @60°F: 1.461 – 1.491 the material safety data sheet (MSDS) Product Weight:: 12.18 – 12.43 Lbs/US for safety and handling precautions. Gallon pH (neat): 14 pH (1% solution): > 11.5 DELIVERY Viscosity (cps): 155 @ 25°C 80 @ 45°C 55-gallon drums, 330-gallon totes, bulk tank trucks and railcars SPECIFICATIONS Sodium aluminate, solution, 8, UN1819, % Al2O3: 19.5 – 20.5 PG II % Na2O: 17.9 – 19.1 % Na2Al2O4: 31.4 – 33.0 Molar Ratio (Na2O / Al2O3): 1.48 – 1.54 PRODUCTION Iron: 200 ppm, max Silica: 225 ppm, max USALCO has production facilities in: PRINCIPAL USES Ashtabula, Ohio Fairfield, Ohio Drinking water / wastewater treatment – removal Michigan City, Indiana of suspended matter and phosphorus CUSTOMER SERVICE Catalyst, zeolite, molecular sieve manufacturing If you have any questions concerning Coating for titanium dioxide pigments this material, please contact our Inside Sales Department at: Pulp and paper manufacturing – pitch control and sizing agent. 410-918-2230 or [email protected] 2601 Cannery Avenue • Baltimore, MD 21226 • 410-918-2230 • FAX: 410-918-2240 • www.usalco.com .

Copy Link

Recommended publications

This Dissertation Has Been 62—2136 M Icrofilm Ed Exactly As Received GIELISSE, Peter Jacob M., 1934- INVESTIGATION of PHASE EQ
This dissertation has been 62—2136 microfilmed exactly as received GIELISSE, Peter Jacob M., 1934- INVESTIGATION OF PHASE EQUILIBRIA IN THE SYSTEM ALUMINA-BORON OXIDE-SILICA. The Ohio State University, Ph.D., 1961 M ineralogy University Microfilms, Inc., Ann Arbor, Michigan INVESTIGATION OP PHASE EQUILIBRIA IN THE SYSTEM ALUMINA-BORON OXIDE-SILICA DISSERTATION Presented in Partial Fulfillment of the Requirements for the Degree Doctor of Philosophy in the Graduate School of the Ohio State University By Peter Jacob M. Gielisse, M. S. The Ohio State University 1961 Approved by Adviser Department of Mineralogy ACKNOWLEDGMENTS The writer wishes to extend his sincere thanks to the many people without whose help the preparation of this dissertation would have been impossible. He is indebted in particular to his adviser, Dr. Wilfrid R. Foster, for his invaluable aid, advice and many kindnesses; to the other members of the faculty of the Department of Mineral ogy, Drs. Ernest G. Ehlers, Henry E. Wenden, and Rodney T Tettenhorst; and to his friend and colleague, Thomas J. Rockett. Acknowledgment is also made for financial support re ceived under contract No. AF 33(616)-3189, sponsored by Aeronautical Research Laboratories, Air Force Research Division, Wright Patterson Air Force Base, Ohio; as well as for aid received through a Mershon National Graduate Fellowship awarded to the writer by the Mershon Committee on Education in National Security for 1960-‘61'. It goes without saying that he is also most grate ful to his wife, Anna, for her excellent help and encour agement over the years. TABLE OF CONTENTS Page INTRODUCTION ......................................
[Show full text]
Implementation of Mathematical Equation for Calculating Alumina Extraction from Bauxite Tailing Digestion
International Conference on Applied Mathematics, Simulation and Modelling (AMSM 2016) Implementation of Mathematical Equation for Calculating Alumina Extraction from Bauxite Tailing Digestion Saini Hu Mineral and Coal Technology Research and Development CenterJalan Jenderal Sudirman No. 623 Bandung-Indonesia Abstract—Research on bauxite digesting using pressurized Washing is one of methods that are usually used to upgrade reactor at a capacity of 86,66 kg of feed/batch had been alumina content of bauxite by separating primary mineral conducted. Bauxite with -150 mesh of particle size is reacted impurities like clay, silica, iron, and titanium that are with 42,15 kg of caustic soda with concentration of 433,49 g/l at attached on the surface of crude bauxite [3]. Trommol screen the temperature of 140oC for 1.0 to 2.5 hours using steam as is common equipment to wash and screen coarse bauxite heating media. Lime added are varied from 3 to 9 kg. After from very fine particles size by supporting pressurized spray processing for a certain period of time, slurry product is water. By using water spraying and screening, smaller transferred into a Mixer. To evaluate percent yield of Al2O3 particles attached on the surface of crude bauxite is easy to extraction from this process, measuring the height of slurry separate. Therefore, there are two products of washing, level in the Mixer, densities of the slurry, filtrate, and solid namely washed bauxite having +2mm of particle size with residue are conducted. Head sample of bauxite, filtrate and high content of alumina and tailing having –2mm of particle residue are analysed by using wet method to get Al2O3 content size with lower content of alumina.
[Show full text]
Investigation of Lime Usage Impacts on Bauxite Processability at ETI Aluminyum Plant
International Journal of Industrial Chemistry (2019) 10:57–66 https://doi.org/10.1007/s40090-019-0171-x RESEARCH Investigation of lime usage impacts on bauxite processability at ETI Aluminyum Plant Hüseyin Arıkan1 · Gökhan K. Demir2 · Sema Vural3 Received: 29 March 2018 / Accepted: 3 February 2019 / Published online: 11 February 2019 © The Author(s) 2019 Abstract ETI Aluminyum A.Ş., the primary aluminium manufacturer of Turkey, is also one of the major integrated plants of the world capable of performing production from mining until end product. The alumina refnery was designed on a certain boehmitic bauxite quality basis. However, bauxite properties have changed over the years, resulting in the urgent need for process opti- mization to not only keep the refnery cost efcient, but also prevent serious bottlenecks in the near future. Lime can be used to overcome problems when using bauxites with specifc and variable chemical and mineralogical characteristics. Although lime is extensively used when processing diasporic bauxites, the studies on boehmitic bauxites and the overall efects on the process are limited. In this paper, lime impact was investigated at all stages of the Bayer process including the efect on alumina quality, energy and raw material consumptions. The results showed signifcant improvements in the product quality as well as recordable savings on consumptions. Keywords Bayer process · Lime usage · Caustic consumption · Digestion · Alumina quality · Boehmitic bauxite Introduction crystalline structure to boehmite. Diferences in ore compo- sition and presence of iron, silicon and titanium impurities The Bayer process is used for producing alumina (Al2O3) infuence their subsequent processing [3, 4]. Thus, it is nec- from bauxite ore.
[Show full text]
Chemicals Used for Treatment of Water Intended for Human Consumption — Sodium Aluminate BS EN 882:2016 BRITISH STANDARD
BS EN 882:2016 BSI Standards Publication Chemicals used for treatment of water intended for human consumption — Sodium aluminate BS EN 882:2016 BRITISH STANDARD National foreword This British Standard is the UK implementation of EN 882:2016. It supersedes BS EN 882:2004 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee CII/59, Chemicals for drinking water treatment. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. © The British Standards Institution 2016. Published by BSI Standards Limited 2016 ISBN 978 0 580 90466 0 ICS 13.060.20; 71.100.80 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2016. Amendments issued since publication Date Text affected BS EN 882:2016 EUROPEAN STANDARD EN 882 NORME EUROPÉENNE EUROPÄISCHE NORM March 2016 ICS 71.100.80 Supersedes EN 882:2004 English Version Chemicals used for treatment of water intended for human consumption - Sodium aluminate Produits chimiques utilisés pour le traitement de l'eau Produkte zur Aufbereitung von Wasser für den destinée à la consommation humaine - Aluminate de menschlichen Gebrauch - Natriumaluminat sodium This European Standard was approved by CEN on 18 January 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
[Show full text]
Removal of Phosphate from Water by Alumina Prepared from Sodium Aluminate
Asian Journal of Applied Sciences (ISSN: 2321 – 0893) Volume 03 – Issue 06, December 2015 Removal of Phosphate from Water by Alumina Prepared from Sodium Aluminate Reham M. M. Aboelenin, Sohair A. Sayed Ahmed*, Ghada M. Mohamed and M.M.Selim Physical Chemistry Department, National Research Centre NRC, 33 Elbohouth St.- Dokki-Giza- Egypt - P.O. 12622 *Corresponding author' e-mail: sohairabdelaziz [AT] yahoo.com ____________________________________________________________________________________________ ABSTRACT--- A sample of sodium aluminate was prepared from aluminum waste by the reaction with sodium hydroxide. From sodium aluminate, aluminum hydroxide was precipitated by formalin solution. The prepared aluminum hydroxide was characterized using DTA , TGA and XRD. Aluminum oxide was obtained by heating aluminum hydroxide from which adsorbent was obtained and used for removal of phosphate from wastewater. The mechanism of adsorption was discussed. Keywords--- Sodium aluminate, potassium phosphate, adsorption, isotherms. _____________________________________________________________________________________________ 1. INTRODUCTION Pollution of water bodies by phosphorus, an essential macronutrient, is a wide-spread environmental problem, causing eutrophication in lakes and seas and posing a great threat to aquatic environments. In environmental systems, the interaction between phosphate and aluminum hydroxides has attracted considerable attention in two respects. The first concerns the reaction of phosphate with aluminum hydroxide minerals
[Show full text]
A Hundred Years of the Bayer Process for Alumina Production*
Essential Readings in Light Metals: Alumina and Bauxite. Edited by Don Donaldson and Benny E. Raahauge. 2013 The Minerals, Metals & Materials Society. Published 2013 by John Wiley & Sons, Inc. 2. BAYER PROCESS This section includes five significant areas: 1. Bayer Process Design. This first area includes the fundamental principles of Bayer process design as well as the history of the development of the Bayer pro- cess. The basic process has not changed but the development of its application for more than a century is truly remarkable. What is even more remarkable is that sig- nificant further improvement is feasible. 2. Physical Data. Contains much of the materials and liquor data needed to prepare flow sheets and heat and material balances. 3. Calcium Chemistry. Included are papers that discuss the effects and use of lime in the process as well as using lime to re-causticize (react) sodium carbonate back to sodium hydroxide. 4. Silica Chemistry. These papers discuss the dissolution of bauxite silica during digestion and the subsequent reaction that forms solid sodium aluminum silicate (desilication product). 5. Organic Removal. These papers deal with the important subject of removing accumulated sodium organates (originating from organic carbon compounds in the bauxite) from Bayer liquor to enhance alumina product quality and to improve pro- cess productivity of alumina. Equally good papers in the list of recommended readings could not be included as published papers because of the limitation on the size of the book. Fred Williams 83 Essential Readings in Light Metals: Alumina and Bauxite. Edited by Don Donaldson and Benny E.
[Show full text]
W. R. Grace & Co.-Conn. Sodium Aluminate Product Stewardship
W. R. Grace & Co.-Conn. Sodium Aluminate Product Stewardship Summary I. Overview W. R. Grace & Co.-Conn manufactures a limited amount of aqueous sodium aluminate for commercial customers and does not directly supply to the public. Sodium aluminate is produced when aluminum metal reacts with an aqueous solution of sodium hydroxide, creating a strong alkaline or basic liquid. Sodium aluminate, primarily in the liquid form, is used in a variety of controlled industrial uses. II. Chemical Identity – Physical and Chemical Properties Chemical Identity: CAS# (EC inventory): 1302-42-7 CAS Name: Sodium aluminate EC Number: 215-100-1 EC Name: Sodium aluminate RTECS Number: BD1600000 Molecular Formula: NaAlO2 Molecular Weight: 81.9701 Synonyms: aluminum sodium oxide, sodium aluminum dioxide, aluminum sodium dioxide Physical and Chemical Properties: Sodium aluminate is an inorganic chemical that in pure form is a white, hygroscopic and water soluble powder. It may generate heat when mixed with water and reacts exothermically with acids. It is corrosive in both solid and liquid forms. It is non-combustible however, if heated to decomposition it may produce corrosive and or toxic fumes. Most sodium aluminate placed onto the market is the aqueous form with typical concentrations of 25-50%. 1 grace.com Talent | Technology | Trust™ III. Applications Sodium aluminate has broad range of uses. Major applications include use in water and wastewater treatment applications, in papermaking, and as a raw material intermediate in commercial industries. In municipal drinking water and waste water treatment systems it serves as a clarifying aid and assists in the removal of phosphates and fluorides in municipal and industrial wastewater plants.
[Show full text]
Telchem Sodium Aluminate Solution
Issue Date: March 2018 SDS No: 781 Version: V.0.0.1 Telchem Sodium Aluminate Solution Telford Industries Safety Data Sheet according to WHS and ADG requirements SECTION 1 IDENTIFICATION OF THE SUBSTANCE / MIXTURE AND OF THE COMPANY / UNDERTAKING Product Identifier Product name Telchem Sodium Aluminate Solution Chemical Name Sodium Aluminate Synonyms Not Available Proper shipping name SODIUM ALUMINATE SOLUTION Chemical formula NaAlO2 Other means of identification Not Available Relevant identified uses of the substance or mixture and uses advised against Relevant Identified Uses Aluminium production, Cement additive, Process reagent, Water treatment Details of the supplier of the safety data sheet Company Name Telford Industries Address 7 Valentine Street Kewdale WA 6105 Australia Telephone +61 8 9353 2053 / 1800 835 115 Fax +61 8 9353 2054 Website https://www.telfordindustries.com.au/ Email [email protected] Emergency telephone number Association/Organisation Not Available Emergency telephone numbers 1800 774 557 Other Emergency telephone numbers 1800 SPILLS SECTION 2 HAZARDS IDENTIFICATION Classification of the substance or mixture HAZARDOUS CHEMICAL. DANGEROUS GOODS. According to the WHS Regulations and the ADG Code. Poisons Schedule S6 Classification Metal Corrosion Category 1, Skin Corrosion/Irritation Category 1B, Serious Eye Damage Category 1 Label Elements GHS label elements SIGNAL WORD DANGER Page 1 of 10 Issue Date: March 2018 SDS No: 781 Version: V.0.0.1 Hazard statement(s) H290 May be corrosive to metals. H314 Causes severe skin burns and eye damage. Precautionary statement(s) Prevention P260 Do not breathe dust/fume/gas/mist/vapours/spray. P280 Wear protective gloves/protective clothing/eye protection/face protection.
[Show full text]
Sodium Aluminate Solution MSDS No
Sodium Aluminate Solution MSDS No. 132 USALCO 38, USALCO 43, USALCO 45 1/14/2020 Safety Data Sheet 1. IDENTIFICATION Product Identifier Product Name Sodium Aluminate, solution Manufacturer Other means of identification USALCO, LLC SDS # 132 2601 Cannery Ave Baltimore, MD 21226 UN/ID No UN 1819 Synonyms USALCO 38, USALCO 43, USALCO 45 Emergency Telephone Number Company Phone Number 410-918-2230 Emergency Telephone (24 hr) 800- 282-5322 2. HAZARDS IDENTIFICATION Appearance: Viscous colorless to amber liquid. Physical State: Liquid . Odor: No or very mild odor. Classification Skin corrosion/irritation Category 1 Sub-category A Serious eye damage/eye irritation Category 1 Corrosive to Metals Category 1 Signal Word Danger Hazard Statements Causes severe skin burns and eye damage May be corrosive to metals. Precautionary Statements - Prevention Do not breathe fume/gas/mist/vapors/spray Wash face, hands and any exposed skin thoroughly after handling Wear protective gloves/protective clothing/eye protection/face protection Precautionary Statements - Response IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing Immediately call a POISON CENTER or doctor/physician IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower Wash contaminated clothing before reuse IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing Immediately call a POISON CENTER or doctor/physician Precautionary Statements - Storage Store in corrosive resistant container or a container with corrosive resistant inner liner. Precautionary Statements - Disposal Dispose of contents/container to an approved waste disposal facility.
[Show full text]
Carbonation of Sodium Aluminate/Sodium Carbonate Solutions for Precipitation of Alumina Hydrates—Avoiding Dawsonite Formation
crystals Article Carbonation of Sodium Aluminate/Sodium Carbonate Solutions for Precipitation of Alumina Hydrates—Avoiding Dawsonite Formation Danai Marinos 1,* , Dimitrios Kotsanis 1, Alexandra Alexandri 1 , Efthymios Balomenos 1,2 and Dimitrios Panias 1 1 Laboratory of Metallurgy, School of Mining and Metallurgical Engineering, National Technical University of Athens (NTUA), Heroon Polytechniou 9, 15780 Zografou, Greece; [email protected] (D.K.); [email protected] (A.A.); [email protected] (E.B.); [email protected] (D.P.) 2 MYTILINEOS S.A, METTALURGY BUSINESS, Agios Nikolaos, 32003 Voiotia, Greece * Correspondence: [email protected]; Tel.: +30-210-772-2299 Abstract: Experimental work has been performed to investigate the precipitation mechanism of aluminum hydroxide phases from sodium aluminate/sodium carbonate pregnant solutions by carbon dioxide gas purging. Such solutions result from leaching calcium aluminate slags with sodium carbonate solutions, in accordance with the Pedersen process, which is an alternative process for alumina production. The concentration of carbonate ions in the pregnant solution is revealed as a key factor in controlling the nature of the precipitating phase. Synthetic aluminate solutions of varying sodium carbonate concentrations, ranging from 20 to 160 g/L, were carbonated, and the resulting precipitating phases were characterized by X-ray diffraction analysis. Based on the results Citation: Marinos, D.; Kotsanis, D.; Alexandri, A.; Balomenos, E.; Panias, of the previous carbonation tests, a series of experiments were performed in which the duration of D. Carbonation of Sodium carbonation and the aging period of the precipitates varied. For this work, a synthetic aluminate Aluminate/Sodium Carbonate solution containing 20 g/L free Na2CO3 was used.
[Show full text]
Extraction of Alumina from Bauxite Residue for Preparation of Alums and Poly Aluminum Chloride
INDONESIAN MINING JOURNAL Vol. 13, No. 1, February 2010 : 16 - 25 EXTRACTION OF ALUMINA FROM BAUXITE RESIDUE FOR PREPARATION OF ALUMS AND POLY ALUMINUM CHLORIDE MUCHTAR AZIZ and AGUS WAHYUDI R&D Centre for Mineral and Coal Technology Jalan Jenderal Sudirman No. 623 Bandung 40211, Ph. 022 6030483, fax. 022 6003373 e-mail: [email protected] ABSTRACT The chemical composition of West Kalimantan bauxite is 45 pct Al2O3 and 16 pct Fe2O3 that has been extracted to produce alumina and bauxite residue (red mud). The residues contains Al2O3 20 pct and Fe2O3 about 37 pct, wich was furthermore processed by roasting or lime-soda sinterization at temperature of 800- 1100°C. The sintered product was leached with sodium carbonate solution to produce soluble sodium aluminate (2NaAlO2). The solution obtained was then precipitated to produce hydrated alumina (Al(OH)3. Hydrated alumina was then sulfateized by adding ammonium hydroxide, and followed by crystallization to produce high purity of ammonium aluminum sulfate crystals (alums). In addition, hydrated alumina was also chlorinated in stoichiometric amount at mol ratio of OH/Al = 0.5 – 1.5 to form polyaluminum chloride (PAC). The residue obtained from leaching was concentrated by 1000 gauss of magnetic separator to produce iron concentrate as a by product. As the results, sulfatation of hydrated alumina with addition of ammonium hydroxide results high grade of ammonium aluminum sulfate (NH4Al(SO4)2 .12H2O) crystals. Chlorination of hydrated alumina in stoichiometric amount at mol ratio of OH/Al = 1.0 results polyaluminum chloride (PAC) that quality is adjacent to the first type of PAC.
[Show full text]
The Story of Aluminum Experiment in 1827
Laval University From the SelectedWorks of Fathi Habashi 2016 The tS ory of Aluminum Fathi Habashi Available at: https://works.bepress.com/fathi_habashi/189/ METALL-FOMETALL-RUBRSCHUNGRIK Berlin he repeated successfully Oersted’s The Story of Aluminum experiment in 1827. In 1836 he moved to Göttingen to accept a position at the Uni- versity and in 1845 succeeded in making Habashi, F. (1) aluminum in slightly larger amounts from which he was able to show that aluminum Aluminum was first produced on a commercial scale in France in 1856 by reduction was a light metal. of alumina with sodium. At the same time aluminum bronze was manufactured. Bauxite played an important role in the production of the metal. The French process Aluminum production in France gave way to the electrolytic process invented in 1888. Aluminum became the chief competitor for copper regarding its use in the electrical industry. In the beginning it French chemists were also active in research was more expensive than copper but since the 1960s it became much cheaper. Its to produce aluminum. Henri Sainte-Claire position in the Periodic Table is also discussed. Deville (1818-1881) (Fig. 4) professor of chemistry at the École Normale in Paris produced aluminum in 1854 by electro- aturally-occurring alum used sium and few days later, sodium using this lyzing molten aluminum chloride-sodium by alchemists to enhance the battery. Once these two reactive metals chloride mixture since the mixture has a dyeing of textile was known were available they became the focus of low-melting eutectic of 107 °C.
[Show full text]